Wiki source code of Set uplinkdwell time
Last modified by Xiaoling on 2023/04/20 09:16
Hide last authors
author | version | line-number | content |
---|---|---|---|
2.2 | 1 | (% class="wikigeneratedid" %) | |
6.3 | 2 | **Table of** **Contents:** | |
2.2 | 3 | ||
4 | {{toc/}} | ||
5 | |||
6.2 | 6 | ||
7 | |||
8 | |||
1.2 | 9 | = 1. Introduction = | |
1.1 | 10 | ||
6.3 | 11 | ||
1.2 | 12 | This chapter introduces how users can change the uplinkdwell time. | |
1.1 | 13 | ||
3.2 | 14 | ||
1.2 | 15 | = 2. Default uplinkdwelltime = | |
1.1 | 16 | ||
6.3 | 17 | ||
1.2 | 18 | Take AS923 frequency band as an example. We can see the spread spectrum factor corresponding to the data rate. | |
1.1 | 19 | ||
6.3 | 20 | ||
3.2 | 21 | [[image:image-20220527091341-1.png]] | |
1.1 | 22 | ||
6.2 | 23 | ||
6.4 | 24 | The device default (% style="color:blue" %)**uplinkdwelltime=1**(%%), there are **SF7, SF8, SF9 and SF10**. | |
1.1 | 25 | ||
6.4 | 26 | If users want to ues **SF11 and SF12,** they need to set (% style="color:blue" %)**uplinkdwelltime=0**. | |
1.1 | 27 | ||
1.2 | 28 | Users can use AT commands to set uplinkdwell time. | |
1.1 | 29 | ||
6.3 | 30 | ||
5.2 | 31 | [[image:image-20220527091422-2.png]] | |
1.1 | 32 | ||
33 | |||
5.2 | 34 | [[image:image-20220527091503-3.png]] | |
35 | |||
36 | |||
1.2 | 37 | = 3. Use AT command to set uplinkdwell time = | |
1.1 | 38 | ||
6.3 | 39 | ||
1.2 | 40 | Since Dragino LoRaWAN Stack DR_LWS_005, user is able to set the uplink Dwelltime in AS923 and AU915 manual or use a application side downlink command to set it. | |
1.1 | 41 | ||
6.4 | 42 | * Use AT command: (% style="color:blue" %)**AT+DWELLT=0**(%%), set to Uplink Dwelltime=0. | |
1.1 | 43 | ||
6.4 | 44 | * Use AT command: (% style="color:blue" %)**AT+DWELLT=1**(%%), set to Uplink Dwelltime=1. | |
6.3 | 45 | ||
1.2 | 46 | Or via application downlink command: | |
1.1 | 47 | ||
6.4 | 48 | * Downlink Payload:** (% style="color:blue" %)0x2500(%%)**, Set AT+DWELLT=0 to uplink. | |
49 | |||
50 | * Downlink Payload: (% style="color:blue" %)**0x2501**(%%), Set AT+DWELLT=1 to uplink. |