Wiki source code of Firmware Upgrade Instruction -- ASR
Last modified by Edwin Chen on 2024/01/08 09:07
Hide last authors
author | version | line-number | content |
---|---|---|---|
1.11 | 1 | (% class="wikigeneratedid" %) | |
14.2 | 2 | **~ Table of Contents:** | |
1.11 | 3 | ||
4 | {{toc/}} | ||
5 | |||
6 | |||
1.2 | 7 | = 1. Introduction = | |
1.1 | 8 | ||
14.2 | 9 | ||
1.2 | 10 | This article shows the firmware upgrade method and troubleshooting for the below models Dragino sensors. | |
1.1 | 11 | ||
3.2 | 12 | ||
1.2 | 13 | = 2. Model and Connection = | |
1.1 | 14 | ||
1.2 | 15 | == 2.1 LDS01/LWL01 == | |
1.1 | 16 | ||
14.2 | 17 | ||
1.2 | 18 | [[Firmware Location>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LDS01/Firmware/]] | |
1.1 | 19 | ||
14.2 | 20 | ||
1.12 | 21 | ((( | |
1.2 | 22 | Pin Mapping: | |
1.12 | 23 | ))) | |
1.1 | 24 | ||
6.2 | 25 | [[image:image-20220527083845-1.png||height="473" width="915"]] | |
1.1 | 26 | ||
1.2 | 27 | LDS01/LWL01 Pin Mapping | |
1.1 | 28 | ||
3.2 | 29 | ||
15.2 | 30 | **DAP-Link Connection:** | |
1.1 | 31 | ||
3.2 | 32 | [[image:image-20220527083959-2.png]] | |
1.1 | 33 | ||
1.2 | 34 | Connect DAP-Link | |
1.1 | 35 | ||
15.2 | 36 | ||
1.2 | 37 | == 2.2 LDS02/LWL02 == | |
1.1 | 38 | ||
14.2 | 39 | ||
16.3 | 40 | [[Firmware Location(same as LDS01)>>https://www.dropbox.com/sh/9j35mnsxnz0y3ye/AACj5gHGOURGEHCpj-E861Mua?dl=0]] | |
1.1 | 41 | ||
14.2 | 42 | ||
1.12 | 43 | ((( | |
1.2 | 44 | Pin Mapping: | |
1.12 | 45 | ))) | |
1.1 | 46 | ||
6.2 | 47 | [[image:image-20220527084041-3.png||height="378" width="907"]] | |
1.1 | 48 | ||
1.2 | 49 | ||
50 | |||
14.2 | 51 | ||
17.1 | 52 | **LDS02/LDS02 v2.0 Pin Mapping** | |
53 | |||
54 | Connector Type: 2.0mm pitch, 2 x 3 | ||
55 | |||
6.2 | 56 | [[image:image-20220527084230-4.png]] | |
57 | |||
1.2 | 58 | LDS02/LDS02 v2.2 Pin Mapping | |
59 | |||
60 | |||
61 | == 2.3 LHT52 == | ||
62 | |||
14.2 | 63 | ||
16.3 | 64 | [[Firmware Location>>https://www.dropbox.com/sh/ayxhuf5dihtfu6c/AABRe_suu54EdTSFZIbD7t-ea?dl=0]] | |
1.2 | 65 | ||
6.2 | 66 | [[image:image-20220527084401-5.png]] | |
1.2 | 67 | ||
68 | LHT52 Pin Mapping | ||
69 | |||
6.2 | 70 | ||
1.2 | 71 | = 3. How to Upgrade = | |
72 | |||
73 | == 3.1 Use DAP-Link and Connect to the Device as above photos == | ||
74 | |||
14.2 | 75 | ||
1.2 | 76 | We need to connect VDD,GND,SWCLK,SWDIO to DAP-Link. | |
77 | |||
78 | * Connection method: | ||
79 | |||
80 | * GND-GND, | ||
81 | |||
82 | * VDD-3.3V, | ||
83 | |||
84 | * SWCLK-CLK, | ||
85 | |||
86 | * SWDIO-SWD | ||
87 | |||
7.2 | 88 | [[image:image-20220527084505-6.png]] | |
1.2 | 89 | ||
90 | |||
15.2 | 91 | ||
1.2 | 92 | == 3.2 Install PSoCProgrammer 3.27.1 == | |
93 | |||
14.2 | 94 | ||
1.11 | 95 | ((( | |
1.2 | 96 | Download Link: [[PSoCProgrammer3.27.1>>url:https://www.dragino.com/downloads/index.php?dir=tools/]] | |
1.11 | 97 | ))) | |
1.2 | 98 | ||
1.11 | 99 | ((( | |
17.1 | 100 | And then use PSoCProgrammer to upgrade the firmware ( (% style="color:red" %)**must use this version: PSoCProgrammer3.27.1** (%%)) | |
1.11 | 101 | ))) | |
1.2 | 102 | ||
12.2 | 103 | [[image:image-20220527084537-7.png]] | |
1.2 | 104 | ||
105 | |||
106 | == 3.3 Download Sensor Firmware == | ||
107 | |||
14.2 | 108 | ||
16.3 | 109 | Downlink sensor firmware to prepare the update. | |
1.2 | 110 | ||
111 | |||
112 | == 3.4 Upgrade Firmware == | ||
113 | |||
14.2 | 114 | ||
1.2 | 115 | Open PSOC Programmer, select the default configuration, no need to modify | |
116 | |||
12.2 | 117 | [[image:image-20220527084612-8.png]] | |
1.2 | 118 | ||
12.2 | 119 | ||
1.2 | 120 | Click the file icon to select the software to be burned: | |
121 | |||
12.2 | 122 | [[image:image-20220527084705-9.png]] | |
1.2 | 123 | ||
124 | |||
12.2 | 125 | [[image:image-20220527084739-10.png||height="453" width="1034"]] | |
1.2 | 126 | ||
12.2 | 127 | ||
14.2 | 128 | ||
1.10 | 129 | ((( | |
1.2 | 130 | Click the download icon, and the progress bar as shown in the figure below will appear. When PASS appears, it proves that the burning is successful. | |
1.10 | 131 | ))) | |
1.2 | 132 | ||
12.2 | 133 | [[image:image-20220527084831-11.png]] | |
1.2 | 134 | ||
135 | |||
13.2 | 136 | [[image:image-20220527084907-12.png]] | |
137 | |||
16.3 | 138 | ||
1.9 | 139 | ((( | |
16.3 | 140 | (% style="color:red" %)**It is very important to press the reset button after the upgrade., this is to set the device to work in Low Power mode.** | |
1.9 | 141 | ))) | |
1.2 | 142 | ||
1.9 | 143 | ((( | |
16.3 | 144 | (% style="color:red" %)**If you change different LoRa Frequency Bands/Region, you need using **(% style="color:blue" %)**AT+FDR **(% style="color:red" %)**command to restore factory data after program success.** | |
16.2 | 145 | ))) | |
13.2 | 146 | ||
15.2 | 147 | ||
1.2 | 148 | = 4. Trouble Shooting = | |
149 | |||
150 | == 4.1 Unable to detect upgrade == | ||
151 | |||
14.2 | 152 | ||
1.2 | 153 | * Try to shot the bootloader pin to GND and reset the device. So the device will runs in bootloader mode. | |
16.2 | 154 | ||
16.3 | 155 | * Or use (% style="color:blue" %)**AT+IREBOOT=7**(%%) to set the device to work in bootloader mode. |