Firmware Upgrade Instruction -- ASR

author	version	line-number	content
		1	(% class="wikigeneratedid" %)
		2	~ Contents:
		3
		4	{{toc/}}
		5
		6
		7	= 1. Introduction =
		8
		9	This article shows the firmware upgrade method and troubleshooting for the below models Dragino sensors.
		10
		11	= 2. Model and Connection =
		12
		13	== 2.1 LDS01/LWL01 ==
		14
		15	[[Firmware Location>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LDS01/Firmware/]]
		16
		17	(((
		18	Pin Mapping:
		19	)))
		20
		21	[[image:https://wiki.dragino.com/images/thumb/e/e3/ASR_Upgrade_1.png/600px-ASR_Upgrade_1.png\|\|height="298" width="566"]]
		22
		23	LDS01/LWL01 Pin Mapping
		24
		25	DAP-Link Connection:
		26
		27	[[image:https://wiki.dragino.com/images/thumb/7/79/ASR_Upgrade_2.jpg/600px-ASR_Upgrade_2.jpg\|\|height="379" width="504"]]
		28
		29	Connect DAP-Link
		30
		31
		32	== 2.2 LDS02/LWL02 ==
		33
		34	[[Firmware Location(same as LDS01)>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LDS01/Firmware/]]
		35
		36	(((
		37	Pin Mapping:
		38	)))
		39
		40	[[image:https://wiki.dragino.com/images/thumb/8/8b/ASR_Upgrade_LDS02_1.png/600px-ASR_Upgrade_LDS02_1.png\|\|height="256" width="600"]]
		41
		42	LDS02/LDS02 v2.0 Pin Mapping
		43
		44	[[image:https://wiki.dragino.com/images/thumb/1/1c/ASR_Upgrade_LDS02_2.png/600px-ASR_Upgrade_LDS02_2.png\|\|height="246" width="547"]]
		45
		46	LDS02/LDS02 v2.2 Pin Mapping
		47
		48
		49	== 2.3 LHT52 ==
		50
		51	[[Firmware Location>>https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LHT52/firmware/]]
		52
		53	[[image:https://wiki.dragino.com/images/thumb/e/e0/ASR_Upgrade_LHT52_1.png/600px-ASR_Upgrade_LHT52_1.png\|\|height="401" width="553"]]
		54
		55	LHT52 Pin Mapping
		56
		57	= 3. How to Upgrade =
		58
		59	== 3.1 Use DAP-Link and Connect to the Device as above photos ==
		60
		61	We need to connect VDD，GND，SWCLK，SWDIO to DAP-Link.
		62
		63	* Connection method：
		64
		65	* GND-GND,
		66
		67	* VDD-3.3V,
		68
		69	* SWCLK-CLK,
		70
		71	* SWDIO-SWD
		72
		73	[[image:https://wiki.dragino.com/images/8/81/DAPlink.png\|\|alt="DAPlink.png" height="539" width="334"]]
		74
		75
		76	== 3.2 Install PSoCProgrammer 3.27.1 ==
		77
		78	(((
		79	Download Link: [[PSoCProgrammer3.27.1>>url:https://www.dragino.com/downloads/index.php?dir=tools/]]
		80	)))
		81
		82	(((
		83	And then use PSoCProgrammer to upgrade the firmware (must use this version: PSoCProgrammer3.27.1)
		84	)))
		85
		86	[[image:https://wiki.dragino.com/images/0/0f/Ppp1.png\|\|alt="Ppp1.png" height="68" width="318"]]
		87
		88
		89	== 3.3 Download Sensor Firmware ==
		90
		91	Downlink sensor firmware to prepare the update
		92
		93
		94	== 3.4 Upgrade Firmware ==
		95
		96	Open PSOC Programmer, select the default configuration, no need to modify
		97
		98	[[image:https://wiki.dragino.com/images/thumb/9/94/Ppp10.png/600px-Ppp10.png\|\|alt="Ppp10.png" height="198" width="600"]]
		99
		100	Click the file icon to select the software to be burned：
		101
		102	[[image:https://wiki.dragino.com/images/thumb/d/d0/Ppp11.png/600px-Ppp11.png\|\|alt="Ppp11.png" height="218" width="600"]]
		103
		104	[[image:https://wiki.dragino.com/images/thumb/e/ec/Ppp12.png/600px-Ppp12.png\|\|alt="Ppp12.png" height="265" width="600"]]
		105
		106
		107	(((
		108	Click the download icon, and the progress bar as shown in the figure below will appear. When PASS appears, it proves that the burning is successful.
		109	)))
		110
		111	[[image:https://wiki.dragino.com/images/thumb/e/e2/Ppp13.png/600px-Ppp13.png\|\|alt="Ppp13.png" height="337" width="600"]]
		112
		113	[[image:https://wiki.dragino.com/images/thumb/6/6f/Ppp14.png/600px-Ppp14.png\|\|alt="Ppp14.png" height="338" width="600"]]
		114
		115	(((
		116	It is very important to press the reset button after the upgrade., this is to set the device to work in Low Power mode
		117	)))
		118
		119	(((
		120	*If you change different LoRa Frequency Bands/Region, you need using AT+FDR command to restore factory data after program success
		121	)))
		122
		123	= 4. Trouble Shooting =
		124
		125	== 4.1 Unable to detect upgrade ==
		126
		127	* Try to shot the bootloader pin to GND and reset the device. So the device will runs in bootloader mode.
		128	* Or use AT+IREBOOT=7 to set the device to work in bootloader mode.