Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -60,7 +60,7 @@
60	60	If the sender does not get the ACK reply from the receiver, it will retransmit up to 4 times, each interval is 6 seconds, and the UplinkCounter of the retransmission will not increase.
61	61
62	62
63		-== 2.2  Point To Mult-Point ==
	63	+== 2.2  Point To Mult-Point ==
64	64
65	65	=== 2.2.1 Overview ===
66	66
...	...	@@ -375,11 +375,11 @@
375	375	=== 2.3.1 TRIG command is configured in the transmit LT. (LT1)(Since firmware 1.3) ===
376	376
377	377
378		-**AT+TRIGx=a  **Trigger transmit directly without triggering time
	378	+**AT+TRIGx=a          **Trigger transmit directly without triggering time
379	379
380	380	**AT+TRIGx=a,b**  Trigger transmit with triggering time threshold
381	381
382		-**AT+TRIGx=a,b,c  **Trigger transmit with triggering time threshold, and continue to transmit every xx seconds if DI status no change.
	382	+**AT+TRIGx=a,b,c    **Trigger transmit with triggering time threshold, and continue to transmit every xx seconds if DI status no change.
383	383
384	384
385	385	**a=0:** falling edge;
...	...	@@ -439,12 +439,12 @@
439	439
440	440	(% style="color:blue" %)**Case1**:
441	441
442		-AT+DI1TODO1=1 ~/~/ LT2 DO1 will follow LT1 DI1 trigger command, if DI1 of LT1 is trigger high, DO1 of LT2 will output low, if DI1 of LT1 is trigger low, DO2 of LT2 will output high.
	442	+AT+DI1TODO1=1  ~/~/ LT2 DO1 will follow LT1 DI1 trigger command, if DI1 of LT1 is trigger high, DO1 of LT2 will output low, if DI1 of LT1 is trigger low, DO2 of LT2 will output high.
443	443
444	444
445	445	(% style="color:blue" %)**Case2**:
446	446
447		-AT+DI1TODO1=1,60 ~/~/ LT2 DO1 will follow LT1 DI1 trigger command, DO1 will keep the status 60 seconds and then go back to original state.
	447	+AT+DI1TODO1=1,60  ~/~/ LT2 DO1 will follow LT1 DI1 trigger command, DO1 will keep the status 60 seconds and then go back to original state.
448	448
449	449
450	450	=== 2.3.3 Save the RO/DO status during power off(Since firmware 1.3) ===
...	...	@@ -452,19 +452,19 @@
452	452
453	453	Enable/Disbale retain Digital Output/Relay Output after power off / Power On
454	454
455		-AT+DOROSAVE=0  ~/~/ Disable Retain after power off/on
	455	+**AT+DOROSAVE=0**  ~/~/ Disable Retain after power off/on
456	456
457		-AT+DOROSAVE=1  ~/~/ Enable Retain after power off/on
	457	+**AT+DOROSAVE=1**  ~/~/ Enable Retain after power off/on
458	458
459		-AT+DOROSAVE=2,a,b,c,d  ~/~/ set DO/RO port to default state after power on.
	459	+**AT+DOROSAVE=2,a,b,c,d**  ~/~/ set DO/RO port to default state after power on.
460	460
461		-a: for DO1
	461	+**a: **for DO1
462	462
463		-b: for DO2
	463	+**b:** for DO2
464	464
465		-c: for RO1
	465	+**c: **for RO1
466	466
467		-d: for RO2.
	467	+**d:** for RO2.
468	468
469	469
470	470	**Example:**
...	...	@@ -477,9 +477,9 @@
477	477
478	478	DI2 can be used to set LT into sleep mode.
479	479
480		-AT+DI2SLEEP=1  ~/~/  Enable DI2 as Sleep pin
	480	+**AT+DI2SLEEP=1**  ~/~/  Enable DI2 as Sleep pin
481	481
482		-AT+DI2SLEEP=0  ~/~/  Disable DI2 as Sleep pin
	482	+**AT+DI2SLEEP=0**  ~/~/  Disable DI2 as Sleep pin
483	483
484	484	When DI2 is enabled as sleep pin, a falling trigger (with 500ms pulse) will set LT into sleep mode. A raising trigger will wake up it again.
485	485