Changes for page wiki_test

Last modified by Mengting Qiu on 2024/09/05 17:35

From 86.5 to 86.4 From 88.2 to 88.1

From version 88.1

edited by Mengting Qiu
on 2023/09/20 17:33

Change comment: Uploaded new attachment "image-20230920173352-2.png", version {1}

To version 86.5

edited by Xiaoling
on 2023/09/12 10:52

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (2 modified, 0 added, 0 removed)
Attachments (0 modified, 0 added, 2 removed)
- image-20230920172200-1.png
- image-20230920173352-2.png

Details

Page properties

Author

@@ -1,1 +1,1 @@
--XWiki.ting
++XWiki.Xiaoling

Content

@@ -55,7 +55,6 @@
  * 8500mAh Battery for long term use
  * Nano SIM card slot for NB-IoT SIM
--
  == 1.3 Specification ==
@@ -101,7 +101,6 @@
  * STOP Mode: 10uA @ 3.3v
  * Max transmit power: 350mA@3.3v
--
  == 1.4 Rated environmental conditions ==
@@ -178,13 +178,12 @@
  )))
  |(% style="width:167px" %)Fast press ACT 5 times.|(% style="width:117px" %)Deactivate Device|(% style="width:225px" %)(% style="color:red" %)**Red led**(%%) will solid on for 5 seconds. Means device is in Deep Sleep Mode.
++== 1.10 BLE connection ==
--== 1.9 BLE connection ==
++DDS20-NB support BLE remote configure and firmware update.
--DDS45-NB support BLE remote configure and firmware update.
--
  BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:
  * Press button to send an uplink
@@ -194,19 +194,19 @@
  If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.
--== 1.10 Pin Definitions & Switch ==
++== 1.11 Pin Definitions & Switch ==
  [[image:image-20230819104805-5.png]]
--=== 1.10.1 Jumper JP2 ===
++=== 1.11.1 Jumper JP2 ===
  Power on Device when put this jumper.
--=== 1.10.2 BOOT MODE / SW1 ===
++=== 1.11.2 BOOT MODE / SW1 ===
  **1)** (% style="color:blue" %)**ISP**(%%): upgrade mode, device won't have any signal in this mode. but ready for upgrade firmware. LED won't work. Firmware won't run.
@@ -214,7 +214,7 @@
  **2)** (% style="color:blue" %)**Flash**(%%): work mode, device starts to work and send out console output for further debug
--=== 1.10.3 Reset Button ===
++=== 1.11.3 Reset Button ===
  Press to reboot the device.
@@ -222,8 +222,9 @@
  (% style="display:none" %)
--== 1.11 Mechanical ==
++== 1.12 Mechanical ==
++
  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual/WebHome/1675143884058-338.png?rev=1.1||alt="1675143884058-338.png"]]
  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual/WebHome/1675143899218-599.png?rev=1.1||alt="1675143899218-599.png"]]
@@ -233,16 +233,17 @@
  (% style="color:blue" %)**Probe Mechanical:**
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS45%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/1654915562090-396.png?rev=1.1||alt="1654915562090-396.png"]]
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS20%20-%20LoRaWAN%20Liquid%20Level%20Sensor%20User%20Manual/WebHome/image-20220615090910-1.png?rev=1.1||alt="image-20220615090910-1.png"]]
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS20%20-%20LoRaWAN%20Liquid%20Level%20Sensor%20User%20Manual/WebHome/image-20220615090910-2.png?rev=1.1||alt="image-20220615090910-2.png"]]
--= 2. Use DDS45-NB to communicate with IoT Server =
++= 2. Use DDS20-NB to communicate with IoT Server =
  == 2.1 Send data to IoT server via NB-IoT network ==
--The DDS45-NB is equipped with a NB-IoT module, the pre-loaded firmware in DDS45-NB will get environment data from sensors and send the value to local NB-IoT network via the NB-IoT module.  The NB-IoT network will forward this value to IoT server via the protocol defined by DDS45-NB.
++The DDS20-NB is equipped with a NB-IoT module, the pre-loaded firmware in DDS20-NB will get environment data from sensors and send the value to local NB-IoT network via the NB-IoT module.  The NB-IoT network will forward this value to IoT server via the protocol defined by DDS20-NB.
  Below shows the network structure:
@@ -253,7 +253,7 @@
  There are two version: (% style="color:blue" %)**-GE**(%%) and (% style="color:blue" %)**-1D**(%%) version of DDS45-NB.
--(% style="color:blue" %)**GE Version**(%%): This version doesn't include SIM card or point to any IoT server. User needs to use AT Commands to configure below two steps to set DDS45-NB send data to IoT server.
++(% style="color:blue" %)**GE Version**(%%): This version doesn't include SIM card or point to any IoT server. User needs to use AT Commands to configure below two steps to set DDS20-NB send data to IoT server.
  * Install NB-IoT SIM card and configure APN. See instruction of [[Attach Network>>url:http://wiki.dragino.com/xwiki/bin/view/Main/General%20Configure%20to%20Connect%20to%20IoT%20server%20for%20-NB%20%26%20-NS%20NB-IoT%20models/#H2.AttachNetwork]].
@@ -283,13 +283,13 @@
  [[image:image-20230819113244-11.png||height="141" width="367"]]
  )))|(% style="width:170px" %)
--(% style="color:blue" %)**1D Version**(%%): This version has 1NCE SIM card pre-installed and configure to send value to DataCake. User Just need to select the sensor type in DataCake and Activate DDS45-NB and user will be able to see data in DataCake. See here for [[DataCake Config Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/General%20Configure%20to%20Connect%20to%20IoT%20server%20for%20-NB%20%26%20-NS%20NB-IoT%20models/#H3.4Datacake]].
++(% style="color:blue" %)**1D Version**(%%): This version has 1NCE SIM card pre-installed and configure to send value to DataCake. User Just need to select the sensor type in DataCake and Activate DDS20-NB and user will be able to see data in DataCake. See here for [[DataCake Config Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/General%20Configure%20to%20Connect%20to%20IoT%20server%20for%20-NB%20%26%20-NS%20NB-IoT%20models/#H3.4Datacake]].
  == 2.2 Payload Types ==
--To meet different server requirement, DDS45-NB supports different payload type.
++To meet different server requirement, DDS20-NB supports different payload type.
  **Includes:**
@@ -315,7 +315,7 @@
  This is the General Json Format. As below:
--(% style="color:#4472c4" %)**{"IMEI":866207053462762,"temperature":29.2,"humidity":54.2,"battery":3.27,"signal":24,"Model":DDS45-NB, "1":{28.2,48.3,2023/08/10 08:00:37},"2":{28.1,49.1,2023/08/10 07:57:37},"3":{28.1,48.5,2023/08/10 07:54:37},"4":{28.2,48.6,2023/08/10 07:51:37},"5":{28.1,48.9,2023/08/10 07:48:37},"6":{28.2,48.8,2023/08/10 07:45:37},"7":{28.2,48.8,2023/08/10 07:42:37},"8":{28.0,48.8,2023/08/10 07:39:37}}**
++(% style="color:#4472c4" %)**{"IMEI":866207053462762,"temperature":29.2,"humidity":54.2,"battery":3.27,"signal":24,"Model":DDS20-NB, "1":{28.2,48.3,2023/08/10 08:00:37},"2":{28.1,49.1,2023/08/10 07:57:37},"3":{28.1,48.5,2023/08/10 07:54:37},"4":{28.2,48.6,2023/08/10 07:51:37},"5":{28.1,48.9,2023/08/10 07:48:37},"6":{28.2,48.8,2023/08/10 07:45:37},"7":{28.2,48.8,2023/08/10 07:42:37},"8":{28.0,48.8,2023/08/10 07:39:37}}**
  (% style="color:red" %)**Notice, from above payload:**
@@ -324,7 +324,6 @@
  * Json entry 1 ~~ 8 are the last 1 ~~ 8 sampling data as specify by (% style="color:#037691" %)**AT+NOUD=8 ** (%%)Command. Each entry includes (from left to right): Temperature, Humidity, Sampling time.
--
  === 2.2.2 HEX format Payload(Type~=0) ===
@@ -332,7 +332,7 @@
  (% style="color:#4472c4" %)**f86620705346276200640cba16010000000011011801e864d49c2d011a01e364d49925011901eb64d49871011901e564d497bd011a01e664d49709011901e964d49655011a01e864d495a1011a01e864d494ed011801e864d49439**
--[[image:image-20230920172200-1.png||height="198" width="1085"]]
++[[image:1692424009971-458.png]]
  (% style="color:blue" %)**Version:**
@@ -339,7 +339,7 @@
  These bytes include the hardware and software version.
--(% style="color:#037691" %)**Higher byte:**(%%) Specify Sensor Model: 0x00 for DDS45-NB
++(% style="color:#037691" %)**Higher byte:**(%%) Specify Sensor Model: 0x00 for DDS20-NB
  (% style="color:#037691" %)**Lower byte:**(%%) Specify the software version: 0x64=100, means firmware version 100
@@ -397,7 +397,7 @@
  (((
--DDS45-NB will uplink payload via LoRaWAN with below payload format:
++DDS20-NB will uplink payload via LoRaWAN with below payload format:
  )))
  (((
@@ -419,7 +419,7 @@
  === 2.3.1  Battery Info ===
--Check the battery voltage for DDS45-NB.
++Check the battery voltage for DDS20-NB.
  Ex1: 0x0B45 = 2885mV
@@ -430,20 +430,19 @@
  (((
--Get the distance. Flat object range 30mm - 4500mm.
++Get the distance. Flat object range 20mm - 2000mm.
  )))
  (((
--For example, if the data you get from the register is **0x0B 0x05**, the distance between the sensor and the measured object is(% style="color:#4472c4" %)** **
++For example, if the data you get from the register is **0x06 0x05**, the distance between the sensor and the measured object is(% style="color:#4472c4" %)** **
--(% style="color:blue" %)**0B05(H) = 2821 (D) = 2821 mm.**
++(% style="color:blue" %)**0605(H) = 1541 (D) = 1541 mm.**
  )))
  * If the sensor value is 0x0000, it means system doesn't detect ultrasonic sensor.
--* If the sensor value lower than 0x001E (30mm), the sensor value will be 0x00.
++* If the sensor value lower than 0x0014 (20mm), the sensor value will be invalid.
--
  === 2.3.3  Interrupt Pin ===
@@ -496,7 +496,7 @@
  == 2.5 Multi-Samplings and One uplink ==
--To save battery life, DDS45-NB will sample temperature & humidity data every 15 minutes and send one uplink every 2 hours. So each uplink it will include 8 stored data + 1 real-time data. They are defined by:
++To save battery life, DDS20-NB will sample temperature & humidity data every 15 minutes and send one uplink every 2 hours. So each uplink it will include 8 stored data + 1 real-time data. They are defined by:
  * (% style="color:#037691" %)**AT+TR=900**   (%%)     ~/~/ The unit is seconds, and the default is to record data once every 900 seconds (15 minutes, the minimum can be set to 180 seconds)
@@ -510,7 +510,7 @@
  == 2.6 Trggier an uplink by external interrupt ==
--DDS45-NB has an external trigger interrupt function. Users can use the PB15 pin to trigger the upload of data packets.
++DDS20-NB has an external trigger interrupt function. Users can use the PB15 pin to trigger the upload of data packets.
  (% style="color:blue" %)**AT command:**
@@ -524,19 +524,17 @@
  * (% style="color:#037691" %)**AT+INTMOD=3  **(%%)  ~/~/ Trigger by rising edge
++= 3. Configure DDS20-NB =
--= 3. Configure DDS45-NB =
--
  == 3.1 Configure Methods ==
--DDS45-NB supports below configure method:
++DDS20-NB supports below configure method:
  * AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
  * AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].
--
  == 3.2 AT Commands Set ==
@@ -620,7 +620,7 @@
  = 4. Battery & Power Consumption =
--DDS45-NB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
++DDS20-NB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
  [[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
@@ -634,7 +634,7 @@
  * Fix bugs.
--Firmware and changelog can be downloaded from : **[[Firmware download link>>https://www.dropbox.com/sh/l0bszumyrmil3yv/AAAg8LYGeAgDsD_ycCnweD72a?dl=0]]**
++Firmware and changelog can be downloaded from : **[[Firmware download link>>https://www.dropbox.com/sh/nyzeu0lf0amcaek/AAC6UZrqyTcAyJgXOH7l9F9Ka?dl=0]]**
  Methods to Update Firmware:
@@ -642,7 +642,6 @@
  * Update through UART TTL interface : **[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.
--
  = 6. FAQ =
  == 6.1 How can I access t BC660K-GL AT Commands? ==
@@ -653,49 +653,23 @@
  [[See BC660K-GL AT Command set>>url:https://www.dropbox.com/sh/5f6ssda5fum8rvs/AABT68l8ZzWOvZ5eg2qwOoFda?dl=0]]
--== 6.2 Can I use DDS45-NB in condensation environment? ==
++= 7.  Trouble Shooting =
++== 7.1  Why i always see 0x0000 or 0 for the distance value? ==
--DDS45-NB is not suitable to be used in condensation environment. Condensation on the DDS45-NB probe will affect the reading and always got 0.
++(((
++DDS20-NB has a strict [[**installation requirement**>>||anchor="H1.5A0InstallDDS20-NB"]]. Please make sure the installation method exactly follows up with the installation requirement. Otherwise, the reading might be always 0x00.
--= 7. Trouble Shooting =
++If you have followed the instruction requirement exactly but still see the 0x00 reading issue, please. please double-check the decoder, you can check the raw payload to verify.
--== 7.1 Why does the sensor reading show 0 or "No sensor" ==
++
++)))
--
--~1. The measurement object is very close to the sensor, but in the blind spot of the sensor.
--
--2. Sensor wiring is disconnected
--
--3. Not using the correct decoder
--
--
--== 7.2 Abnormal readings The gap between multiple readings is too large or the gap between the readings and the actual value is too large ==
--
--
--1) Please check if there is something on the probe affecting its measurement (condensed water, volatile oil, etc.)
--
--2) Does it change with temperature, temperature will affect its measurement
--
--3) If abnormal data occurs, you can turn on DEBUG mode, Please use downlink or AT COMMAN to enter DEBUG mode.
--
--downlink command: (% style="color:blue" %)**F1 01**(%%), AT command: (% style="color:blue" %)**AT+DDEBUG=1**
--
--4) After entering the debug mode, it will send 20 pieces of data at a time, and you can send its uplink to us for analysis
--
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDDS75%20-%20LoRaWAN%20Distance%20Detection%20Sensor%20User%20Manual/WebHome/image-20230113135125-2.png?width=1057&height=136&rev=1.1||alt="image-20230113135125-2.png"]]
--
--
--Its original payload will be longer than other data. Even though it is being parsed, it can be seen that it is abnormal data.
--
--Please send the data to us for check.
--
--
  = 8. Order Info =
--Part Number: (% style="color:blue" %)**DDS45-NB-XX**
++Part Number: (% style="color:blue" %)**DDS20-NB-XX**
  (% style="color:red" %)**XX**(%%):
@@ -711,7 +711,7 @@
  (% style="color:#037691" %)**Package Includes**:
--* DDS45-NB NB-IoT Distance Detection sensor x 1
++* DDS20-NB NB-IoT Ultrasonic liquid level sensor x 1
  * External antenna x 1
@@ -725,7 +725,6 @@
  * Weight / pcs : 180g
--
  = 10. Support =

image-20230920172200-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.ting

Size

...	...	@@ -1,1 +1,0 @@
1		-37.9 KB

Content

image-20230920173352-2.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.ting

Size

...	...	@@ -1,1 +1,0 @@
1		-63.7 KB

Content

Changes for page wiki_test

Summary

Details

Applications

Navigation