Skip to Content

Changes for page wiki_test

Last modified by Mengting Qiu on 2024/09/05 17:35
From version 82.8
edited by Xiaoling
on 2023/08/19 14:00
Change comment: There is no comment for this version
To version 82.5
edited by Xiaoling
on 2023/08/19 13:53
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -399,9 +399,9 @@
399 399  
400 400  To save battery life, S31-NB will sample temperature & humidity data every 15 minutes and send one uplink every 2 hours. So each uplink it will include 8 stored data + 1 real-time data. They are defined by:
401 401  
402 -* (% style="color:#037691" %)**AT+TR=900**   (%%) ~/~/ The unit is seconds, and the default is to record data once every 900 seconds (15 minutes, the minimum can be set to 180 seconds)
402 +* (% style="color:#037691" %)**AT+TR=900**   (%%) ~/~/  The unit is seconds, and the default is to record data once every 900 seconds (15 minutes, the minimum can be set to 180 seconds)
403 403  
404 -* (% style="color:#037691" %)**AT+NOUD=8**  (%%)~/~/  The device uploads 8 sets of recorded data by default. Up to 32 sets of record data can be uploaded.
404 +* (% style="color:#037691" %)**AT+NOUD=8**  (%%)~/~/   The device uploads 8 sets of recorded data by default. Up to 32 sets of record data can be uploaded.
405 405  
406 406  The diagram below explains the relationship between TR, NOUD, and TDC more clearly:
407 407  
... ... @@ -418,12 +418,12 @@
418 418  
419 419  (% style="color:#037691" %)**AT+ SHHUM=min,max**
420 420  
421 -Example: AT+ SHHUM=50,80  ~/~/ Alarm when humidity lower than 50 or higher than 80.
421 +Example: AT+ SHHUM=50,80 ~/~/ Alarm when humidity lower than 50 or higher than 80.
422 422  
423 423  
424 424  (% style="color:#037691" %)**AT+ SHTEMP=min,max**
425 425  
426 -Example: AT+ SHTEMP=20,30  ~/~/ Alarm when temperature lower than 20 or higher than 30
426 +Example: AT+ SHTEMP=20,30 ~/~/ Alarm when temperature lower than 20 or higher than 30
427 427  
428 428  
429 429  (% style="color:red" %)**Notice:**
... ... @@ -441,15 +441,15 @@
441 441  
442 442  (% style="color:blue" %)**AT command:**
443 443  
444 -* (% style="color:#037691" %)**AT+INTMOD **(%%) ~/~/ Set the trigger interrupt mode
444 +* (% style="color:#037691" %)**AT+INTMOD **(%%) ~/~/ Set the trigger interrupt mode
445 445  
446 -* (% style="color:#037691" %)**AT+INTMOD=0 **(%%) ~/~/ Disable Interrupt
446 +* (% style="color:#037691" %)**AT+INTMOD=0 **(%%) ~/~/Disable Interrupt
447 447  
448 -* (% style="color:#037691" %)**AT+INTMOD=1 **(%%) ~/~/ Trigger by rising and falling edge
448 +* (% style="color:#037691" %)**AT+INTMOD=1 **(%%) ~/~/Trigger by rising and falling edge
449 449  
450 -* (% style="color:#037691" %)**AT+INTMOD=2 **(%%) ~/~/ Trigger by falling edge
450 +* (% style="color:#037691" %)**AT+INTMOD=2 **(%%) ~/~/Trigger by falling edge
451 451  
452 -* (% style="color:#037691" %)**AT+INTMOD=3  **(%%) ~/~/ Trigger by rising edge
452 +* (% style="color:#037691" %)**AT+INTMOD=3  **(%%) ~/~/Trigger by rising edge
453 453  
454 454  
455 455  = 3. Configure S31x-NB =
... ... @@ -463,84 +463,200 @@
463 463  
464 464  * AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].
465 465  
466 -== 3.2 AT Commands Set ==
466 +* LoRaWAN Downlink.  Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
467 467  
468 468  
469 -AT+<CMD>?        : Help on <CMD>
469 +== 3.2 General Commands ==
470 470  
471 -AT+<CMD>         : Run <CMD>
472 472  
473 -AT+<CMD>=<value> : Set the value
472 +These commands are to configure:
474 474  
475 -AT+<CMD>=?       : Get the value
474 +* General system settings like: uplink interval.
475 +* LoRaWAN protocol & radio related command.
476 476  
477 +They are same for all Dragino Devices which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:
477 477  
478 -**General Commands**      
479 +[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
479 479  
480 -AT                    : Attention       
481 481  
482 -AT?                            : Short Help     
482 +== 3.3 Commands special design for S31x-LB ==
483 483  
484 -ATZ                            : MCU Reset    
485 485  
486 -AT+TDC           : Application Data Transmission Interval
485 +These commands only valid for S31x-LB, as below:
487 487  
488 -AT+CFG           : Print all configurations
489 489  
490 -AT+CFGMOD           : Working mode selection
488 +=== 3.3.1 Set Transmit Interval Time ===
491 491  
492 -AT+DEUI                             : Get or set the Device ID
493 493  
494 -AT+INTMOD            : Set the trigger interrupt mode
491 +Feature: Change LoRaWAN End Node Transmit Interval.
495 495  
496 -AT+5VT           : Set extend the time of 5V power  
493 +(% style="color:blue" %)**AT Command: AT+TDC**
497 497  
498 -AT+PRO          : Choose agreement
495 +(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
496 +|=(% style="width: 156px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 137px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="background-color:#D9E2F3;color:#0070C0" %)**Response**
497 +|(% style="width:156px" %)AT+TDC=?|(% style="width:137px" %)Show current transmit Interval|(((
498 +30000
499 +OK
500 +the interval is 30000ms = 30s
501 +)))
502 +|(% style="width:156px" %)AT+TDC=60000|(% style="width:137px" %)Set Transmit Interval|(((
503 +OK
504 +Set transmit interval to 60000ms = 60 seconds
505 +)))
499 499  
500 -AT+RXDL                  : Extend the sending and receiving time
507 +(% style="color:blue" %)**Downlink Command: 0x01**
501 501  
502 -AT+DNSCFG         :  Get or Set DNS Server
509 +Format: Command Code (0x01) followed by 3 bytes time value.
503 503  
504 -AT+GETSENSORVALUE   : Returns the current sensor measurement
511 +If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
505 505  
506 -AT+NOUD      : Get or Set the number of data to be uploaded
513 +* Example 1: Downlink Payload: 0100001E  ~/~/  Set Transmit Interval (TDC) = 30 seconds
514 +* Example 2: Downlink Payload: 0100003C  ~/~/  Set Transmit Interval (TDC) = 60 seconds
507 507  
508 -AT+CDP     : Read or Clear cached data
516 +=== 3.3.2 Get Device Status ===
509 509  
510 -AT+SHTEMP: Get or Set alarm of temp
511 511  
512 -AT+SHHUM: Get or Set alarm of moisture
519 +Send a LoRaWAN downlink to ask device send Alarm settings.
513 513  
514 -AT+SERVADDR                 : Server Address
521 +(% style="color:blue" %)**Downlink Payload:  **(%%)0x26 01
515 515  
516 -**UDP Management**
523 +Sensor will upload Device Status via FPORT=5. See payload section for detail.
517 517  
518 -AT+CFM          : Upload confirmation mode (only valid for UDP)
519 519  
526 +=== 3.3.3 Set Temperature Alarm Threshold ===
520 520  
521 -**MQTT Management**
522 522  
523 -AT+CLIENT               : Get or Set MQTT client
529 +* (% style="color:blue" %)**AT Command:**
524 524  
525 -AT+UNAME              : Get or Set MQTT Username
531 +(% style="color:#037691" %)**AT+SHTEMP=min,max**
526 526  
527 -AT+PWD                  : Get or Set MQTT password
533 +* When min=0, and max≠0, Alarm higher than max
534 +* When min≠0, and max=0, Alarm lower than min
535 +* When min≠0 and max≠0, Alarm higher than max or lower than min
528 528  
529 -AT+PUBTOPIC                   : Get or Set MQTT publish topic
537 +Example:
530 530  
531 -AT+SUBTOPIC                   : Get or Set MQTT subscription topic
539 + AT+SHTEMP=0,30   ~/~/ Alarm when temperature higher than 30.
532 532  
541 +* (% style="color:blue" %)**Downlink Payload:**
533 533  
534 -**Information**          
543 +(% style="color:#037691" %)**0x(0C 01 00 1E)**  (%%) ~/~/ Set AT+SHTEMP=0,30
535 535  
536 -AT+FDR           : Factory Data Reset
545 +(% style="color:red" %)**(note: 3^^rd^^ byte= 0x00 for low limit(not set), 4^^th^^ byte = 0x1E for high limit: 30)**
537 537  
538 -AT+PWORD             : Serial Access Password
539 539  
540 -AT+LDATA  : Get the last upload data
548 +=== 3.3.4 Set Humidity Alarm Threshold ===
541 541  
542 -AT+CDP                              : Read or Clear cached data
543 543  
551 +* (% style="color:blue" %)**AT Command:**
552 +
553 +(% style="color:#037691" %)**AT+SHHUM=min,max**
554 +
555 +* When min=0, and max≠0, Alarm higher than max
556 +* When min≠0, and max=0, Alarm lower than min
557 +* When min≠0 and max≠0, Alarm higher than max or lower than min
558 +
559 +Example:
560 +
561 + AT+SHHUM=70,0  ~/~/ Alarm when humidity lower than 70%.
562 +
563 +* (% style="color:blue" %)**Downlink Payload:**
564 +
565 +(% style="color:#037691" %)**0x(0C 02 46 00)**(%%)  ~/~/ Set AT+SHTHUM=70,0
566 +
567 +(% style="color:red" %)**(note: 3^^rd^^ byte= 0x46 for low limit (70%), 4^^th^^ byte = 0x00 for high limit (not set))**
568 +
569 +
570 +=== 3.3.5 Set Alarm Interval ===
571 +
572 +
573 +The shortest time of two Alarm packet. (unit: min)
574 +
575 +* (% style="color:blue" %)**AT Command:**
576 +
577 +(% style="color:#037691" %)**AT+ATDC=30** (%%) ~/~/ The shortest interval of two Alarm packets is 30 minutes, Means is there is an alarm packet uplink, there won't be another one in the next 30 minutes.
578 +
579 +* (% style="color:blue" %)**Downlink Payload:**
580 +
581 +(% style="color:#037691" %)**0x(0D 00 1E)**(%%)     **~-~--> ** Set AT+ATDC=0x 00 1E = 30 minutes
582 +
583 +
584 +=== 3.3.6 Get Alarm settings ===
585 +
586 +
587 +Send a LoRaWAN downlink to ask device send Alarm settings.
588 +
589 +* (% style="color:#037691" %)**Downlink Payload:  **(%%)0x0E 01
590 +
591 +**Example:**
592 +
593 +[[image:image-20230524110211-4.png]]
594 +
595 +**Explain:**
596 +
597 +* Alarm & MOD bit is 0x7C, 0x7C >> 2 = 0x31: Means this message is the Alarm settings message.
598 +
599 +=== 3.3.7 Set Interrupt Mode ===
600 +
601 +
602 +Feature, Set Interrupt mode for PA8 of pin.
603 +
604 +When AT+INTMOD=0 is set, PA8 is used as a digital input port.
605 +
606 +(% style="color:blue" %)**AT Command: AT+INTMOD**
607 +
608 +(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
609 +|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 197px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 158px;background-color:#D9E2F3;color:#0070C0" %)**Response**
610 +|(% style="width:154px" %)AT+INTMOD=?|(% style="width:196px" %)Show current interrupt mode|(% style="width:157px" %)(((
611 +0
612 +OK
613 +the mode is 0 =Disable Interrupt
614 +)))
615 +|(% style="width:154px" %)AT+INTMOD=2|(% style="width:196px" %)(((
616 +Set Transmit Interval
617 +0. (Disable Interrupt),
618 +~1. (Trigger by rising and falling edge)
619 +2. (Trigger by falling edge)
620 +3. (Trigger by rising edge)
621 +)))|(% style="width:157px" %)OK
622 +
623 +(% style="color:blue" %)**Downlink Command: 0x06**
624 +
625 +Format: Command Code (0x06) followed by 3 bytes.
626 +
627 +This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
628 +
629 +* Example 1: Downlink Payload: 06000000  ~/~/  Turn off interrupt mode
630 +* Example 2: Downlink Payload: 06000003  ~/~/  Set the interrupt mode to rising edge trigger
631 +
632 +=== 3.3.8 Set Power Output Duration ===
633 +
634 +
635 +Control the output duration 5V . Before each sampling, device will
636 +
637 +~1. first enable the power output to external sensor,
638 +
639 +2. keep it on as per duration, read sensor value and construct uplink payload
640 +
641 +3. final, close the power output.
642 +
643 +(% style="color:blue" %)**AT Command: AT+5VT**
644 +
645 +(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
646 +|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 197px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 158px;background-color:#D9E2F3;color:#0070C0" %)**Response**
647 +|(% style="width:154px" %)AT+5VT=?|(% style="width:196px" %)Show 5V open time.|(% style="width:157px" %)0 (default)
648 +OK
649 +|(% style="width:154px" %)AT+5VT=1000|(% style="width:196px" %)Close after a delay of 1000 milliseconds.|(% style="width:157px" %)OK
650 +
651 +(% style="color:blue" %)**Downlink Command: 0x07**
652 +
653 +Format: Command Code (0x07) followed by 2 bytes.
654 +
655 +The first and second bytes are the time to turn on.
656 +
657 +* Example 1: Downlink Payload: 070000  **~-~-->**  AT+5VT=0
658 +* Example 2: Downlink Payload: 0701F4  **~-~-->**  AT+5VT=500
659 +
544 544  = 4. Battery & Power Consumption =
545 545  
546 546