Changes for page wiki_test

Last modified by Mengting Qiu on 2024/09/05 17:35

From 82.7 to 82.6 From 82.14 to 82.13

From version 82.13

edited by Xiaoling
on 2023/08/19 14:12

Change comment: There is no comment for this version

To version 82.7

edited by Xiaoling
on 2023/08/19 13:56

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -299,6 +299,7 @@
  * Json entry 1 ~~ 8 are the last 1 ~~ 8 sampling data as specify by (% style="color:#037691" %)**AT+NOUD=8 ** (%%)Command. Each entry includes (from left to right): Temperature, Humidity, Sampling time.
++
  === 2.2.2 HEX format Payload(Type~=0) ===
@@ -400,7 +400,7 @@
  * (% style="color:#037691" %)**AT+TR=900**   (%%)     ~/~/ The unit is seconds, and the default is to record data once every 900 seconds (15 minutes, the minimum can be set to 180 seconds)
--* (% style="color:#037691" %)**AT+NOUD=8**     (%%)~/~/  The device uploads 8 sets of recorded data by default. Up to 32 sets of record data can be uploaded.
++* (% style="color:#037691" %)**AT+NOUD=8**     (%%)~/~/  The device uploads 8 sets of recorded data by default. Up to 32 sets of record data can be uploaded.
  The diagram below explains the relationship between TR, NOUD, and TDC more clearly:
@@ -432,6 +432,7 @@
  * If user only want to send only min or max, user can set the alarm to a value that device won’t reach. For example: (% style="color:#037691" %)**AT+SHTEMP=-80,0.**
++
  == 2.6 Trggier an uplink by external interrupt ==
@@ -449,6 +449,7 @@
  * (% style="color:#037691" %)**AT+INTMOD=3  **(%%)  ~/~/ Trigger by rising edge
++
  = 3. Configure S31x-NB =
  == 3.1 Configure Methods ==
@@ -460,108 +460,224 @@
  * AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].
--== 3.2 AT Commands Set ==
++* AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
++* AT Command via UART Connection : See [[UART Connection>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20NB%20ST-BC660K-GL%20base%20model%20%28for%20AT%20Commands%2C%20firmware%20upgrade%29/]].
++== 3.2 General Commands ==
--AT+<CMD>?           : Help on <CMD>
--AT+<CMD>                      : Run <CMD>
++These commands are to configure:
--AT+<CMD>=<value>      : Set the value
++* General system settings like: uplink interval.
++* LoRaWAN protocol & radio related command.
--AT+<CMD>=?          : Get the value
++They are same for all Dragino Devices which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:
++[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
--(% style="color:blue" %)**General Commands**
--AT                    : Attention
++== 3.3 Commands special design for S31x-LB ==
--AT?                  : Short Help
--ATZ                 : MCU Reset
++These commands only valid for S31x-LB, as below:
--AT+TDC          : Application Data Transmission Interval
--AT+CFG          : Print all configurations
++=== 3.3.1 Set Transmit Interval Time ===
--AT+CFGMOD           : Working mode selection
--AT+DEUI                  : Get or set the Device ID
++Feature: Change LoRaWAN End Node Transmit Interval.
--AT+INTMOD            : Set the trigger interrupt mode
++(% style="color:blue" %)**AT Command: AT+TDC**
--AT+5VT           : Set extend the time of 5V power
++(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
++|=(% style="width: 156px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 137px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="background-color:#D9E2F3;color:#0070C0" %)**Response**
++|(% style="width:156px" %)AT+TDC=?|(% style="width:137px" %)Show current transmit Interval|(((
++30000
++OK
++the interval is 30000ms = 30s
++)))
++|(% style="width:156px" %)AT+TDC=60000|(% style="width:137px" %)Set Transmit Interval|(((
++OK
++Set transmit interval to 60000ms = 60 seconds
++)))
--AT+PRO          : Choose agreement
++(% style="color:blue" %)**Downlink Command: 0x01**
--AT+RXDL        : Extend the sending and receiving time
++Format: Command Code (0x01) followed by 3 bytes time value.
--AT+DNSCFG   : Get or Set DNS Server
++If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
--AT+GETSENSORVALUE   : Returns the current sensor measurement
++* Example 1: Downlink Payload: 0100001E       ~/~/  Set Transmit Interval (TDC) = 30 seconds
++* Example 2: Downlink Payload: 0100003C       ~/~/  Set Transmit Interval (TDC) = 60 seconds
--AT+NOUD  : Get or Set the number of data to be uploaded
++=== 3.3.2 Get Device Status ===
--AT+CDP     : Read or Clear cached data
--AT+SHTEMP:   Get or Set alarm of temp
++Send a LoRaWAN downlink to ask device send Alarm settings.
--AT+SHHUM:   Get or Set alarm of moisture
++(% style="color:blue" %)**Downlink Payload:  **(%%)0x26 01
--AT+SERVADDR :   Server Address
++Sensor will upload Device Status via FPORT=5. See payload section for detail.
--(% style="color:blue" %)**UDP Management**
++=== 3.3.3 Set Temperature Alarm Threshold ===
--AT+CFM  :    Upload confirmation mode (only valid for UDP)
++* (% style="color:blue" %)**AT Command:**
--(% style="color:blue" %)**MQTT Management**
++(% style="color:#037691" %)**AT+SHTEMP=min,max**
--AT+CLIENT               : Get or Set MQTT client
++* When min=0, and max≠0, Alarm higher than max
++* When min≠0, and max=0, Alarm lower than min
++* When min≠0 and max≠0, Alarm higher than max or lower than min
--AT+UNAME              : Get or Set MQTT Username
++Example:
--AT+PWD                  : Get or Set MQTT password
++   AT+SHTEMP=0,30   ~/~/ Alarm when temperature higher than 30.
--AT+PUBTOPIC          : Get or Set MQTT publish topic
++* (% style="color:blue" %)**Downlink Payload:**
--AT+SUBTOPIC          : Get or Set MQTT subscription topic
++(% style="color:#037691" %)**0x(0C 01 00 1E)**  (%%)     ~/~/ Set AT+SHTEMP=0,30
++(% style="color:red" %)**(note: 3^^rd^^ byte= 0x00 for low limit(not set), 4^^th^^ byte = 0x1E for high limit: 30)**
--(% style="color:blue" %)**Information**
--AT+FDR              : Factory Data Reset
++=== 3.3.4 Set Humidity Alarm Threshold ===
--AT+PWORD        : Serial Access Password
--AT+LDATA           : Get the last upload data
++* (% style="color:blue" %)**AT Command:**
--AT+CDP               : Read or Clear cached data
++(% style="color:#037691" %)**AT+SHHUM=min,max**
++* When min=0, and max≠0, Alarm higher than max
++* When min≠0, and max=0, Alarm lower than min
++* When min≠0 and max≠0, Alarm higher than max or lower than min
++Example:
++
++   AT+SHHUM=70,0      ~/~/ Alarm when humidity lower than 70%.
++
++* (% style="color:blue" %)**Downlink Payload:**
++
++(% style="color:#037691" %)**0x(0C 02 46 00)**(%%)         ~/~/ Set AT+SHTHUM=70,0
++
++(% style="color:red" %)**(note: 3^^rd^^ byte= 0x46 for low limit (70%), 4^^th^^ byte = 0x00 for high limit (not set))**
++
++
++=== 3.3.5 Set Alarm Interval ===
++
++
++The shortest time of two Alarm packet. (unit: min)
++
++* (% style="color:blue" %)**AT Command:**
++
++(% style="color:#037691" %)**AT+ATDC=30** (%%)      ~/~/ The shortest interval of two Alarm packets is 30 minutes, Means is there is an alarm packet uplink, there won't be another one in the next 30 minutes.
++
++* (% style="color:blue" %)**Downlink Payload:**
++
++(% style="color:#037691" %)**0x(0D 00 1E)**(%%)     **~-~--> ** Set AT+ATDC=0x 00 1E = 30 minutes
++
++
++=== 3.3.6 Get Alarm settings ===
++
++
++Send a LoRaWAN downlink to ask device send Alarm settings.
++
++* (% style="color:#037691" %)**Downlink Payload:  **(%%)0x0E 01
++
++**Example:**
++
++[[image:image-20230524110211-4.png]]
++
++**Explain:**
++
++* Alarm & MOD bit is 0x7C, 0x7C >> 2 = 0x31: Means this message is the Alarm settings message.
++
++=== 3.3.7 Set Interrupt Mode ===
++
++
++Feature, Set Interrupt mode for PA8 of pin.
++
++When AT+INTMOD=0 is set, PA8 is used as a digital input port.
++
++(% style="color:blue" %)**AT Command: AT+INTMOD**
++
++(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
++|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 197px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 158px;background-color:#D9E2F3;color:#0070C0" %)**Response**
++|(% style="width:154px" %)AT+INTMOD=?|(% style="width:196px" %)Show current interrupt mode|(% style="width:157px" %)(((
++0
++OK
++the mode is 0 =Disable Interrupt
++)))
++|(% style="width:154px" %)AT+INTMOD=2|(% style="width:196px" %)(((
++Set Transmit Interval
++0. (Disable Interrupt),
++~1. (Trigger by rising and falling edge)
++2. (Trigger by falling edge)
++3. (Trigger by rising edge)
++)))|(% style="width:157px" %)OK
++
++(% style="color:blue" %)**Downlink Command: 0x06**
++
++Format: Command Code (0x06) followed by 3 bytes.
++
++This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
++
++* Example 1: Downlink Payload: 06000000       ~/~/  Turn off interrupt mode
++* Example 2: Downlink Payload: 06000003      ~/~/   Set the interrupt mode to rising edge trigger
++
++=== 3.3.8 Set Power Output Duration ===
++
++
++Control the output duration 5V . Before each sampling, device will
++
++~1. first enable the power output to external sensor,
++
++2. keep it on as per duration, read sensor value and construct uplink payload
++
++3. final, close the power output.
++
++(% style="color:blue" %)**AT Command: AT+5VT**
++
++(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
++|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 197px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 158px;background-color:#D9E2F3;color:#0070C0" %)**Response**
++|(% style="width:154px" %)AT+5VT=?|(% style="width:196px" %)Show 5V open time.|(% style="width:157px" %)0 (default)
++OK
++|(% style="width:154px" %)AT+5VT=1000|(% style="width:196px" %)Close after a delay of 1000 milliseconds.|(% style="width:157px" %)OK
++
++(% style="color:blue" %)**Downlink Command: 0x07**
++
++Format: Command Code (0x07) followed by 2 bytes.
++
++The first and second bytes are the time to turn on.
++
++* Example 1: Downlink Payload: 070000     **~-~-->**   AT+5VT=0
++* Example 2: Downlink Payload: 0701F4      **~-~-->**  AT+5VT=500
++
  = 4. Battery & Power Consumption =
--S31x-NB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
++S31x-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
  [[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
--= 5. Firmware update =
++= 5. OTA Firmware update =
--User can change device firmware to::
++(% class="wikigeneratedid" %)
++User can change firmware S31x-LB to:
++* Change Frequency band/ region.
  * Update with new features.
--
  * Fix bugs.
--Firmware and changelog can be downloaded from : **[[Firmware download link>>https://www.dropbox.com/sh/fhb3uyl4gt6clru/AAAiZVTFcxrfE1JOOyfcgO9ha?dl=0]]**
++Firmware and changelog can be downloaded from : **[[Firmware download link>>https://www.dropbox.com/sh/fis3g6nmhv0eokg/AAC6BcCZaX4BdqZkduUvZ3jIa?dl=0]]**
++
  Methods to Update Firmware:
--* (Recommended way) OTA firmware update via BLE: [[**Instruction**>>url:http://wiki.dragino.com/xwiki/bin/view/Main/BLE_Firmware_Update_NB_Sensors_BC660K-GL/]].
++* (Recommanded way) OTA firmware update via wireless : **[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]**
  * Update through UART TTL interface : **[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.
  = 6. FAQ =

Changes for page wiki_test

Summary

Details

Applications

Navigation