Skip to Content

Changes for page wiki_test

Last modified by Mengting Qiu on 2024/09/05 17:35
From version 66.1
edited by Bei Jinggeng
on 2023/08/02 10:43
Change comment: There is no comment for this version
To version 80.10
edited by Xiaoling
on 2023/08/19 13:41
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -S31-LB / S31B-LB LoRaWAN Outdoor Temperature & Humidity Sensor User Manual
1 +S31-NB/S31B-NB_BN-IoT Outdoor Temperature & Humidity Sensor User Manual
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Bei
1 +XWiki.Xiaoling
Content
... ... @@ -1,9 +1,8 @@
1 1  (% style="text-align:center" %)
2 -[[image:S31-B.jpg]]
2 +[[image:image-20230819102136-3.png]]
3 3  
4 4  
5 5  
6 -
7 7  **Table of Contents：**
8 8  
9 9  {{toc/}}
... ... @@ -15,38 +15,37 @@
15 15  
16 16  = 1. Introduction =
17 17  
18 -== 1.1 What is S31x-LB LoRaWAN Temperature & Humidity Sensor ==
17 +== 1.1 What is S31x-NB NB-IoT Temperature & Humidity Sensor ==
19 19  
20 20  
21 -The Dragino S31x-LB is a (% style="color:blue" %)**LoRaWAN Temperature and Humidity Sensor**(%%) for Internet of Things solution. It is used to measure the (% style="color:blue" %)**surrounding environment temperature and relative air humidity precisely**(%%), and then upload to IoT server via LoRaWAN wireless protocol.
20 +The Dragino S31-NB and S31B-NB are (% style="color:blue" %)**NB-IoT Temperature and Humidity Sensor**(%%) for Internet of Things solution. It is used to measure the surrounding (% style="color:blue" %)**environment temperature and relative air humidity precisely**(%%), and then upload to IoT server via NB-IoT network*.
22 22  
23 -The temperature & humidity sensor used in S31x-LB is SHT31, which is fully calibrated, linearized, and temperature compensated digital output from Sensirion, it provides a strong reliability and long-term stability. The SHT31 is fixed in a (% style="color:blue" %)**waterproof anti-condensation casing**(%%) for long term use.
22 +The temperature & humidity sensor used in S31-NB is SHT31, which is fully calibrated, linearized, and temperature compensated digital output from Sensirion, it provides a strong reliability and long-term stability. The SHT31 is fixed in a (% style="color:blue" %)**waterproof anti-condensation casing**(%%) for long term use.
24 24  
25 -The LoRa wireless technology used in S31x-LB allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
24 +S31-NB supports different uplink methods include (% style="color:blue" %)**TCP, MQTT, UDP** for different application requirement. and Support Uplinks to various IoT Servers.
26 26  
27 -S31x-LB supports (% style="color:blue" %)**Temperature & Humdity alarm feature**(%%), user can set temperature alarm for instant notice. S31x-LB supports Datalog feature, it can save the data when there is no LoRaWAN network and uplink when network recover.
26 +S31-NB is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), It is designed for long term use up to several years. (Real-world battery life depends on the use environment, update period and uplink method. Please check related Power Analyze report).
28 28  
29 -S31x-LB (% style="color:blue" %)**supports BLE configure**(%%) and (% style="color:blue" %)**wireless OTA update**(%%) which make user easy to use.
28 +*make sure you have NB-IoT coverage locally.
30 30  
31 -S31x-LB is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), it is designed for long term use up to 5 years.
32 32  
33 -Each S31x-LB is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
31 +[[image:1692411831805-116.png]]
34 34  
35 35  
36 36  == 1.2 ​Features ==
37 37  
38 38  
39 -* LoRaWAN 1.0.3 Class A
37 +* NB-IoT Bands: B1/B2/B3/B4/B5/B8/B12/B13/B17/B18/B19/B20/B25/B28/B66/B70/B85 @H-FDD
40 40  * Ultra-low power consumption
41 -* External 3 meters SHT31 probe (For S31-LB)
42 -* Measure range -55°C ~~ 125°C
39 +* External 3 meters SHT31 probe (For S31-NB)
40 +* Measure range -40°C ~~ 85°C
43 43  * Temperature & Humidity alarm
44 -* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
45 -* Support Bluetooth v5.1 and LoRaWAN remote configure
46 -* Support wireless OTA update firmware
42 +* Multiply Sampling and one uplink
43 +* Support Bluetooth v5.1 remote configure and update firmware
47 47  * Uplink on periodically
48 48  * Downlink to change configure
49 49  * 8500mAh Battery for long term use
47 +* Nano SIM card slot for NB-IoT SIM
50 50  
51 51  == 1.3 Specification ==
52 52  
... ... @@ -53,7 +53,7 @@
53 53  
54 54  (% style="color:#037691" %)**Common DC Characteristics:**
55 55  
56 -* Supply Voltage: built in 8500mAh Li-SOCI2 battery , 2.5v ~~ 3.6v
54 +* Supply Voltage: 2.1v ~~ 3.6v
57 57  * Operating Temperature: -40 ~~ 85°C
58 58  
59 59  (% style="color:#037691" %)**Temperature Sensor:**
... ... @@ -70,37 +70,66 @@
70 70  * Resolution: 0.01% RH
71 71  * Long Term Shift: <0.25 %RH/yr
72 72  
73 -(% style="color:#037691" %)**LoRa Spec:**
71 +(% style="color:#037691" %)**NB-IoT Spec:**
74 74  
75 -* Frequency Range,  Band 1 (HF): 862 ~~ 1020 Mhz
76 -* Max +22 dBm constant RF output vs.
77 -* RX sensitivity: down to -139 dBm.
78 -* Excellent blocking immunity
73 +**NB-IoT Module: BC660K-GL**
79 79  
75 +Support Bands:
76 +
77 +* B1 @H-FDD: 2100MHz
78 +* B2 @H-FDD: 1900MHz
79 +* B3 @H-FDD: 1800MHz
80 +* B4 @H-FDD: 2100MHz
81 +* B5 @H-FDD: 860MHz
82 +* B8 @H-FDD: 900MHz
83 +* B12 @H-FDD: 720MHz
84 +* B13 @H-FDD: 740MHz
85 +* B17 @H-FDD: 730MHz
86 +* B18 @H-FDD: 870MHz
87 +* B19 @H-FDD: 870MHz
88 +* B20 @H-FDD: 790MHz
89 +* B25 @H-FDD: 1900MHz
90 +* B28 @H-FDD: 750MHz
91 +* B66 @H-FDD: 2000MHz
92 +* B70 @H-FDD: 2000MHz
93 +* B85 @H-FDD: 700MHz
94 +
80 80  (% style="color:#037691" %)**Battery:**
81 81  
82 82  * Li/SOCI2 un-chargeable battery
83 83  * Capacity: 8500mAh
84 -* Self-Discharge: <1% / Year @ 25°C
99 +* Self Discharge: <1% / Year @ 25°C
85 85  * Max continuously current: 130mA
86 86  * Max boost current: 2A, 1 second
87 87  
88 88  (% style="color:#037691" %)**Power Consumption**
89 89  
90 -* Sleep Mode: 5uA @ 3.3v
91 -* LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm
105 +* STOP Mode: 10uA @ 3.3v
106 +* Max transmit power: 350mA@3.3v
92 92  
93 -== 1.4 Sleep mode and working mode ==
108 +== 1.4 Applications ==
94 94  
95 95  
111 +* Smart Buildings & Home Automation
112 +* Logistics and Supply Chain Management
113 +* Smart Metering
114 +* Smart Agriculture
115 +* Smart Cities
116 +* Smart Factory
117 +
118 +
119 +== 1.5 Sleep mode and working mode ==
120 +
121 +
96 96  (% style="color:blue" %)**Deep Sleep Mode: **(%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.
97 97  
98 98  (% style="color:blue" %)**Working Mode:** (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.
99 99  
100 100  
101 -== 1.5 Button & LEDs ==
102 102  
128 +== 1.6 Button & LEDs ==
103 103  
130 +
104 104  [[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675071855856-879.png]]
105 105  
106 106  
... ... @@ -107,20 +107,20 @@
107 107  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
108 108  |=(% style="width: 167px;background-color:#D9E2F3;color:#0070C0" %)**Behavior on ACT**|=(% style="width: 117px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 225px;background-color:#D9E2F3;color:#0070C0" %)**Action**
109 109  |(% style="width:167px" %)Pressing ACT between 1s < time < 3s|(% style="width:117px" %)Send an uplink|(% style="width:225px" %)(((
110 -If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, (% style="color:blue" %)**blue led** (%%)will blink once.
137 +If sensor has already attached to NB-IoT network, sensor will send an uplink packet, (% style="color:blue" %)**blue led** (%%)will blink once.
111 111  Meanwhile, BLE module will be active and user can connect via BLE to configure device.
112 112  )))
113 113  |(% style="width:167px" %)Pressing ACT for more than 3s|(% style="width:117px" %)Active Device|(% style="width:225px" %)(((
114 -(% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:#037691" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network.
141 +(% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:#037691" %)**OTA mode**(%%) for 3 seconds. And then start to attach NB-IoT network.
115 115  (% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.
116 -Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device join or not join LoRaWAN network.
143 +Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device attach NB-IoT network or not.
117 117  )))
118 118  |(% style="width:167px" %)Fast press ACT 5 times.|(% style="width:117px" %)Deactivate Device|(% style="width:225px" %)(% style="color:red" %)**Red led**(%%) will solid on for 5 seconds. Means device is in Deep Sleep Mode.
119 119  
120 -== 1.6 BLE connection ==
147 +== 1.7 BLE connection ==
121 121  
122 122  
123 -S31x-LB support BLE remote configure.
150 +S31x-NB support BLE remote configure and firmware update.
124 124  
125 125  
126 126  BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:
... ... @@ -132,443 +132,336 @@
132 132  If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.
133 133  
134 134  
135 -== 1.7 Pin Definitions ==
162 +== 1.8 Pin Definitions & Switch ==
136 136  
137 -[[image:http://8.211.40.43/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SN50v3-LB/WebHome/image-20230610163213-1.png?width=699&height=404&rev=1.1||alt="image-20230610163213-1.png"]]
138 138  
165 +S31x-NB use the mother board from S31-NB which as below.
139 139  
140 -== 1.8 Hardware Variant ==
167 +[[image:image-20230819104805-5.png]]
141 141  
142 142  
143 -(% border="1" cellspacing="5" style="width:472px" %)
144 -|=(% style="width: 102px;background-color:#D9E2F3;color:#0070C0" %)Model|=(% style="width: 190px;background-color:#D9E2F3;color:#0070C0" %)Photo|=(% style="width: 187px; background-color:#D9E2F3;color:#0070C0" %)Probe Info
145 -|(% style="width:102px" %)(((
146 -S31-LB
147 -)))|(% style="width:190px" %)[[image:image-20230527093214-2.jpeg]]|(% style="width:187px" %)(((
148 -1 x SHT31 Probe
149 149  
150 -Cable Length : 2 meters
171 +=== 1.8.1 Jumper JP2 ===
151 151  
152 -
153 -)))
154 -|(% style="width:102px" %)(((
155 -S31B-LB
156 -)))|(% style="width:190px" %)[[image:image-20230527093155-1.jpeg]]|(% style="width:187px" %)(((
157 -1 x SHT31 Probe
158 158  
159 -Installed in device.
160 -)))
174 +Power on Device when put this jumper.
161 161  
162 -(% style="display:none" %)
163 163  
177 +=== 1.8.2 BOOT MODE / SW1 ===
164 164  
165 165  
166 -== 1.9 Mechanical ==
180 +1) (% style="color:blue" %)**ISP**(%%): upgrade mode, device won't have any signal in this mode. but ready for upgrade firmware. LED won't work. Firmware won't run.
167 167  
182 +2) (% style="color:blue" %)**Flash**(%%): work mode, device starts to work and send out console output for further debug
168 168  
169 -[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143884058-338.png]]
170 170  
185 +=== 1.8.3 Reset Button ===
171 171  
172 -[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143899218-599.png]]
173 173  
188 +Press to reboot the device.
174 174  
175 -[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143909447-639.png]]
176 176  
177 177  
178 -= 2. Configure S31x-LB to connect to LoRaWAN network =
192 +== 1.9 Hardware Variant ==
179 179  
180 -== 2.1 How it works ==
181 181  
195 +(% border="1" cellspacing="5" style="width:410px" %)
196 +|=(% style="width: 102px;background-color:#4F81BD;color:white" %)Model|=(% style="width: 126px; background-color:#4F81BD;color:white" %)Photo|=(% style="width: 179px;background-color:#4F81BD;color:white" %)Probe Info
197 +|(% style="width:102px" %)(((
198 +S31-LB
199 +)))|(% style="width:126px" %)(((
200 +(% style="text-align:center" %)
201 +[[image:image-20230819110632-6.png||height="130" width="104"]]
202 +)))|(% style="width:179px" %)(((
203 +1 x SHT31 Probe
182 182  
183 -The S31x-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the S31x-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
205 +Cable Length : 3 meters
184 184  
207 +
208 +)))
209 +|(% style="width:102px" %)(((
210 +S31B-LB
211 +)))|(% style="width:126px" %)(((
212 +(% style="text-align:center" %)
213 +[[image:image-20230819110702-7.png||height="164" width="90"]]
214 +)))|(% style="width:179px" %)(((
215 +1 x SHT31 Probe
185 185  
186 -== 2.2 ​Quick guide to connect to LoRaWAN server (OTAA) ==
217 +Installed in device.
218 +)))
187 187  
220 +(% style="display:none" %)
188 188  
189 -Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.
190 190  
191 -The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
192 192  
193 193  
194 -(% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from S31x-LB.
225 += 2. Use S31-NB to communicate with IoT Server =
195 195  
196 -Each S31x-LB is shipped with a sticker with the default device EUI as below:
227 +== 2.1 Send data to IoT server via NB-IoT network ==
197 197  
198 -[[image:image-20230426084152-1.png||alt="图片-20230426084152-1.png" height="233" width="502"]]
199 199  
230 +The S31-NB is equipped with a NB-IoT module, the pre-loaded firmware in S31-NB will get environment data from sensors and send the value to local NB-IoT network via the NB-IoT module.  The NB-IoT network will forward this value to IoT server via the protocol defined by S31-NB.
200 200  
201 -You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
202 202  
233 +Below shows the network structure:
203 203  
204 -(% style="color:blue" %)**Register the device**
235 +[[image:1692415924540-357.png]]
205 205  
206 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/1654935135620-998.png?rev=1.1||alt="1654935135620-998.png"]]
207 207  
238 +There are two version: (% style="color:blue" %)**-GE**(%%) and (% style="color:blue" %)**-1D**(%%) version of S31-NB.
208 208  
209 -(% style="color:blue" %)**Add APP EUI and DEV EUI**
210 210  
211 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-4.png?width=753&height=551&rev=1.1||alt="图片-20220611161308-4.png"]]
241 +(% style="color:blue" %)**GE Version**(%%): This version doesn’t include SIM card or point to any IoT server. User needs to use AT Commands to configure below two steps to set S31-NB send data to IoT server.
212 212  
243 +1. Install NB-IoT SIM card and configure APN. See instruction of [[Attach Network>>url:http://wiki.dragino.com/xwiki/bin/view/Main/General%20Configure%20to%20Connect%20to%20IoT%20server%20for%20-NB%20%26%20-NS%20NB-IoT%20models/#H2.AttachNetwork]].
213 213  
214 -(% style="color:blue" %)**Add APP EUI in the application**
245 +1. Set up sensor to point to IoT Server. See instruction of [[Configure to Connect Different Servers>>url:http://wiki.dragino.com/xwiki/bin/view/Main/General%20Configure%20to%20Connect%20to%20IoT%20server%20for%20-NB%20%26%20-NS%20NB-IoT%20models/#H3.Configuretoconnecttodifferentservers]]. 
215 215  
247 +Below shows result of different server as a glance.
216 216  
217 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-5.png?width=742&height=601&rev=1.1||alt="图片-20220611161308-5.png"]]
218 218  
250 +(% border="1" cellspacing="4" style="width:515px" %)
251 +|(% style="width:100px;background-color:#4F81BD;color:white" %)**Servers**|(% style="width:300px;background-color:#4F81BD;color:white" %)**Dash Board**|(% style="width:115px;background-color:#4F81BD;color:white" %)**Comments**
252 +|(% style="width:127px" %)[[Node-Red>>url:http://wiki.dragino.com/xwiki/bin/view/Main/General%20Configure%20to%20Connect%20to%20IoT%20server%20for%20-NB%20%26%20-NS%20NB-IoT%20models/#H3.5A0Node-RedA028viaA0MQTT29]]|(% style="width:385px" %)[[image:image-20230819113244-8.png||height="183" width="367"]]|(% style="width:170px" %)
253 +|(% style="width:127px" %)[[DataCake>>url:http://wiki.dragino.com/xwiki/bin/view/Main/General%20Configure%20to%20Connect%20to%20IoT%20server%20for%20-NB%20%26%20-NS%20NB-IoT%20models/#H3.4Datacake]]|(% style="width:385px" %)[[image:image-20230819113244-9.png||height="120" width="369"]]|(% style="width:170px" %)
254 +|(% style="width:127px" %)[[Tago.IO>>url:http://wiki.dragino.com/xwiki/bin/view/Main/General%20Configure%20to%20Connect%20to%20IoT%20server%20for%20-NB%20%26%20-NS%20NB-IoT%20models/#H3.7A0Tago.ioA028viaA0MQTT29]]|(% style="width:385px" %) |(% style="width:170px" %)
255 +|(% style="width:127px" %)[[General UDP>>url:http://wiki.dragino.com/xwiki/bin/view/Main/General%20Configure%20to%20Connect%20to%20IoT%20server%20for%20-NB%20%26%20-NS%20NB-IoT%20models/#H3.1GeneralA0UDPA0Connection]]|(% style="width:385px" %)Raw Payload. Need Developer to design Dash Board|(% style="width:170px" %)
256 +|(% style="width:127px" %)[[General MQTT>>url:http://wiki.dragino.com/xwiki/bin/view/Main/General%20Configure%20to%20Connect%20to%20IoT%20server%20for%20-NB%20%26%20-NS%20NB-IoT%20models/#H3.2GeneralA0MQTTA0Connection]]|(% style="width:385px" %)Raw Payload. Need Developer to design Dash Board|(% style="width:170px" %)
257 +|(% style="width:127px" %)[[ThingSpeak>>url:http://wiki.dragino.com/xwiki/bin/view/Main/General%20Configure%20to%20Connect%20to%20IoT%20server%20for%20-NB%20%26%20-NS%20NB-IoT%20models/#H3.3A0ThingSpeakA028viaA0MQTT29]]|(% style="width:385px" %)[[image:image-20230819113244-10.png||height="82" width="291"]]|(% style="width:170px" %)
258 +|(% style="width:127px" %)[[ThingsBoard>>url:http://wiki.dragino.com/xwiki/bin/view/Main/General%20Configure%20to%20Connect%20to%20IoT%20server%20for%20-NB%20%26%20-NS%20NB-IoT%20models/#H3.6A0ThingsBoard.CloudA028viaA0MQTT29]]|(% style="width:385px" %)[[image:image-20230819113244-11.png||height="113" width="293"]]|(% style="width:170px" %)
259 +|(% style="width:127px" %) |(% style="width:385px" %) |(% style="width:170px" %)
219 219  
220 -(% style="color:blue" %)**Add APP KEY**
221 221  
222 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-6.png?width=744&height=485&rev=1.1||alt="图片-20220611161308-6.png"]]
262 +(% style="color:blue" %)**1D Version**(%%): This version has 1NCE SIM card pre-installed and configure to send value to DataCake. User Just need to select the sensor type in DataCake and Activate S31-NB and user will be able to see data in DataCake. See here for [[DataCake Config Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/General%20Configure%20to%20Connect%20to%20IoT%20server%20for%20-NB%20%26%20-NS%20NB-IoT%20models/#H3.4Datacake]].
223 223  
224 224  
225 -(% style="color:blue" %)**Step 2:**(%%) Activate on S31x-LB
265 +== 2.2 ​Payload Types ==
226 226  
227 227  
228 -Press the button for 5 seconds to activate the S31x-LB.
268 +To meet different server requirement, S31-NB supports different payload type.
229 229  
230 -(% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:blue" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.
270 +Includes:
231 231  
232 -After join success, it will start to upload messages to TTN and you can see the messages in the panel.
272 +* [[General JSON format payload>>path:#General_Json]]. (Type=5)
233 233  
274 +* [[HEX format Payload>>path:#HEX_Payload]]. (Type=0)
234 234  
235 -== 2.3 ​Uplink Payload ==
276 +* [[ThingSpeak Format>>path:#ThingSpeak_Payload]]. (Type=1)
236 236  
237 -=== 2.3.1 Device Status, FPORT~=5 ===
278 +* [[ThingsBoard Format>>path:#ThingsBoard_Payload]]. (Type=3)
238 238  
280 +User can specify the payload type when choose the connection protocol. Example:
239 239  
240 -Users can use the downlink command(**0x26 01**) to ask S31x-LB to send device configure detail, include device configure status. S31x-LB will uplink a payload via FPort=5 to server.
282 +(% style="color:#037691" %)**AT+PRO=2,0**  (%%) ~/~/Use UDP Connection & hex Payload
241 241  
242 -The Payload format is as below.
284 +(% style="color:#037691" %)**AT+PRO=2,5**   (%%) ~/~/ Use UDP Connection & Json Payload
243 243  
286 +(% style="color:#037691" %)**AT+PRO=3,5 ** (%%) ~/~/ Use MQTT Connection & Json Payload
244 244  
245 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
246 -|(% colspan="6" style="background-color:#d9e2f3; color:#0070c0" %)**Device Status (FPORT=5)**
247 -|(% style="width:103px" %)**Size (bytes)**|(% style="width:72px" %)**1**|**2**|(% style="width:91px" %)**1**|(% style="width:86px" %)**1**|(% style="width:44px" %)**2**
248 -|(% style="width:103px" %)**Value**|(% style="width:72px" %)Sensor Model|Firmware Version|(% style="width:91px" %)Frequency Band|(% style="width:86px" %)Sub-band|(% style="width:44px" %)BAT
249 249  
250 -Example parse in TTNv3
289 +=== 2.2.1 General Json Format (Type ===
251 251  
252 -[[image:image-20230524144422-1.png||height="174" width="1080"]]
291 +5) ===
253 253  
293 +This is the General Json Format. As below:
254 254  
255 -(% style="color:#037691" %)**Sensor Model**(%%): For S31x-LB, this value is 0x0A
256 256  
257 -(% style="color:#037691" %)**Firmware Version**(%%): 0x0100, Means: v1.0.0 version
296 +(% style="color:#4472c4" %)**{"IMEI":866207053462762,"temperature":29.2,"humidity":54.2,"battery":3.27,"signal":24,"Model":S31x-NB, "1":{28.2,48.3,2023/08/10 08:00:37},"2":{28.1,49.1,2023/08/10 07:57:37},"3":{28.1,48.5,2023/08/10 07:54:37},"4":{28.2,48.6,2023/08/10 07:51:37},"5":{28.1,48.9,2023/08/10 07:48:37},"6":{28.2,48.8,2023/08/10 07:45:37},"7":{28.2,48.8,2023/08/10 07:42:37},"8":{28.0,48.8,2023/08/10 07:39:37}}**
258 258  
259 -(% style="color:#037691" %)**Frequency Band**:
260 260  
261 -0x01: EU868
262 262  
263 -0x02: US915
300 +(% style="color:red" %)Notice, from above payload:
264 264  
265 -0x03: IN865
302 +* Temperature , Humidity , Battery & Signal are the value at uplink time.
266 266  
267 -0x04: AU915
304 +* Json entry 1 ~~ 8 are the last 1 ~~ 8 sampling data as specify by (% style="color:#037691" %)**AT+NOUD=8 ** (%%)Command. Each entry includes (from left to right): Temperature, Humidity, Sampling time.
268 268  
269 -0x05: KZ865
270 270  
271 -0x06: RU864
272 272  
273 -0x07: AS923
308 +=== 2.2.2 HEX format Payload(Type ===
274 274  
275 -0x08: AS923-1
310 +0) ===
276 276  
277 -0x09: AS923-2
278 278  
279 -0x0a: AS923-3
313 +This is the HEX Format. As below:
280 280  
281 -0x0b: CN470
315 +(% style="color:#4472c4" %)**f86620705346276200640cba16010000000011011801e864d49c2d011a01e364d49925011901eb64d49871011901e564d497bd011a01e664d49709011901e964d49655011a01e864d495a1011a01e864d494ed011801e864d49439**
282 282  
283 -0x0c: EU433
284 284  
285 -0x0d: KR920
318 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image001.png]]
286 286  
287 -0x0e: MA869
288 288  
321 +(% style="color:blue" %)**Version:**
289 289  
290 -(% style="color:#037691" %)**Sub-Band**:
323 +These bytes include the hardware and software version.
291 291  
292 -AU915 and US915:value 0x00 ~~ 0x08
325 +(% style="color:#037691" %)**Higher byte:**(%%) Specify Sensor Model: 0x00 for S31B-NB & S31-NB
293 293  
294 -CN470: value 0x0B ~~ 0x0C
327 +(% style="color:#037691" %)**Lower byte:**(%%) Specify the software version: 0x64=100, means firmware version 100
295 295  
296 -Other Bands: Always 0x00
297 297  
330 +(% style="color:#037691" %)**BAT (Battery Info):**
298 298  
299 -(% style="color:#037691" %)**Battery Info**:
332 +Ex1: 0x0CBA = 3258mV
300 300  
301 -Check the battery voltage.
302 302  
303 -Ex1: 0x0B45 = 2885mV
335 +(% style="color:blue" %)**Signal Strength:**
304 304  
305 -Ex2: 0x0B49 = 2889mV
337 +NB-IoT Network signal Strength.
306 306  
339 +**Ex1: 0x16 = 22**
307 307  
308 -=== 2.3.2  Sensor Data. FPORT~=2 ===
341 +**0**  -113dBm or less
309 309  
343 +**1**  -111dBm
310 310  
311 -Sensor Data is uplink via FPORT=2
345 +**2...30** -109dBm... -53dBm
312 312  
313 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
314 -|=(% style="width: 60px;background-color:#D9E2F3;color:#0070C0" %)(((
315 -**Size(bytes)**
316 -)))|=(% style="width: 40px;background-color:#D9E2F3;color:#0070C0" %)2|=(% style="width: 90px;background-color:#D9E2F3;color:#0070C0" %)4|=(% style="width: 150px; background-color: #D9E2F3;color:#0070C0" %)1|=(% style="width: 80px; background-color: #D9E2F3;color:#0070C0" %)**2**|=(% style="width: 80px; background-color: #D9E2F3;color:#0070C0" %)2
317 -|(% style="width:99px" %)Value|(% style="width:69px" %)(((
318 -Battery
319 -)))|(% style="width:130px" %)(((
320 -Unix TimeStamp
321 -)))|(% style="width:194px" %)(((
322 -Alarm Flag & MOD& Level of PA8
323 -)))|(% style="width:106px" %)(((
324 -Temperature
325 -)))|(% style="width:97px" %)(((
326 -Humidity
327 -)))
347 +**31**   -51dBm or greater
328 328  
329 -[[image:image-20230524144456-2.png||height="180" width="1142"]]
349 +**99**    Not known or not detectable
330 330  
331 331  
332 -==== (% style="color:#4472c4" %)**Battery**(%%) ====
352 +(% style="color:blue" %)**Temperature: **
333 333  
334 -Sensor Battery Level.
335 -
336 -Ex1: 0x0B45 = 2885mV
337 -
338 -Ex2: 0x0B49 = 2889mV
339 -
340 -
341 -==== (% style="color:#4472c4" %)**Temperature**(%%) ====
342 -
343 -**Example**:
344 -
345 345  If payload is: 0105H:  (0105 & 8000 == 0), temp = 0105H /10 = 26.1 degree
346 346  
347 347  If payload is: FF3FH :  (FF3F & 8000 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.
348 348  
349 -（FF3F & 8000：Judge whether the highest bit is 1, when the highest bit is 1, it is negative）
358 +(FF3F & 8000：Judge whether the highest bit is 1, when the highest bit is 1, it is negative)
350 350  
351 351  
352 -==== (% style="color:#4472c4" %)**Humidity**(%%) ====
353 353  
362 +(% style="color:blue" %)**Humidity:   **
354 354  
355 -Read:0x(0197)=412    Value:  412 / 10=41.2, So 41.2%
364 +Read:0295(H)=661(D)    Value:  661 / 10=66.1, So 66.1%
356 356  
357 357  
358 -==== (% style="color:#4472c4" %)**Alarm Flag & MOD & Level of PA8**(%%) ====
367 +(% style="color:blue" %)**TimeStamp:   **
359 359  
369 +Unit TimeStamp Example: 64d49439(H) = 1691653177(D)
360 360  
361 -**Example:**
371 +Put the decimal value into this link(https:~/~/www.epochconverter.com/) to get the time.
362 362  
363 -If payload & 0x01 = 0x01  **~-~->** This is an Alarm Message.It means that the temperature and humidity exceed the alarm value or trigger an interrupt.
364 364  
365 -If payload & 0x01 = 0x00  **~-~->** This is a normal uplink message, no alarm.
374 +=== 2.2.3 ThingsBoard Payload(Type ===
366 366  
367 -If payload & 0x80>>7 = 0x01  **~-~->** The PA8 is low level.
376 +3) ===
368 368  
369 -If payload & 0x80>>7 =0x00  **~-~->** The PA8 is high level.
378 +Type3 payload special design for ThingsBoard, it will also configure other default server to ThingsBoard.
370 370  
371 -If payload >> 2 = 0x00  **~-~->**  means MOD=1, This is a sampling uplink message.
372 372  
373 -If payload >> 2 = 0x31  **~-~->**  means MOD=31, this message is a reply message for polling, this message contains the alarm settings. see [[this link>>path:#HPolltheAlarmsettings:]] for detail. 
381 +(% style="color:#4472c4" %)**{"IMEI":866207053462762,"temperature":29.2,"humidity":54.2,"battery":3.27,"signal":24}**
374 374  
375 375  
376 -== 2.4 Payload Decoder file ==
384 +=== 2.2.4 ThingSpeak Payload(Type ===
377 377  
386 +1) ===
378 378  
379 -In TTN, use can add a custom payload so it shows friendly reading
388 +This payload meets ThingSpeak platform requirement. It includes only four fields. Form 1~~4 are:
380 380  
381 -In the page (% style="color:#037691" %)**Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder**(%%) to add the decoder from:
390 +Temperature, Humidity, Battery & Signal. This payload type only valid for ThingsSpeak Platform
382 382  
383 -[[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/S31-LB%26S31B-LB>>https://github.com/dragino/dragino-end-node-decoder/tree/main/S31-LB%26S31B-LB]]
384 384  
393 +As below:
385 385  
386 -== 2.5 Datalog Feature ==
395 +(% style="color:#4472c4" %)**field1=27.9&field2=49.9&field3=3.23&field4=28**
387 387  
388 388  
389 -Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, S31x-LB will store the reading for future retrieving purposes.
398 +== 2.3 Test Uplink and Change Update Interval ==
390 390  
391 391  
392 -=== 2.5.1 Ways to get datalog via LoRaWAN ===
401 +By default, Sensor will send uplinks (% style="color:blue" %)**every 2 hours**(%%) & AT+NOUD=8
393 393  
394 394  
395 -Set [[PNACKMD=1>>||anchor="H2.5.4DatalogUplinkpayload28FPORT3D329"]], S31x-LB will wait for ACK for every uplink, when there is no LoRaWAN network,S31x-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
404 +User can use below commands to change the (% style="color:blue" %)**uplink interval**.
396 396  
397 -* (((
398 -a) S31x-LB will do an ACK check for data records sending to make sure every data arrive server.
399 -)))
400 -* (((
401 -b) S31x-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but S31x-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if S31x-LB gets a ACK, S31x-LB will consider there is a network connection and resend all NONE-ACK messages.
402 -)))
406 +(% style="color:#037691" %)** AT+TDC=600      ** (%%) ~/~/ Set Update Interval to 600s
403 403  
404 -Below is the typical case for the auto-update datalog feature (Set PNACKMD=1)
405 405  
406 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220703111700-2.png?width=1119&height=381&rev=1.1||alt="图片-20220703111700-2.png" height="381" width="1119"]]
409 +User can also push the button for more than 1 seconds to activate an uplink.
407 407  
408 408  
409 -=== 2.5.2 Unix TimeStamp ===
410 410  
411 411  
412 -S31x-LB uses Unix TimeStamp format based on
414 +== 2.4 Multi-Samplings and One uplink ==
413 413  
414 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-11.png?width=627&height=97&rev=1.1||alt="图片-20220523001219-11.png" height="97" width="627"]]
415 415  
416 -User can get this time from link:  [[https:~~/~~/www.epochconverter.com/>>url:https://www.epochconverter.com/]] :
417 +To save battery life, S31-NB will sample temperature & humidity data every 15 minutes and send one uplink every 2 hours. So each uplink it will include 8 stored data + 1 real-time data. They are defined by:
417 417  
418 -Below is the converter example
419 +* (% style="color:#037691" %)**AT+TR=900**   (%%) ~/~/  The unit is seconds, and the default is to record data once every 900 seconds (15 minutes, the minimum can be set to 180 seconds)
419 419  
420 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-12.png?width=720&height=298&rev=1.1||alt="图片-20220523001219-12.png" height="298" width="720"]]
421 +* (% style="color:#037691" %)**AT+NOUD=8**  (%%)~/~/   The device uploads 8 sets of recorded data by default. Up to 32 sets of record data can be uploaded.
421 421  
423 +The diagram below explains the relationship between TR, NOUD, and TDC more clearly:
422 422  
423 -So, we can use AT+TIMESTAMP=1611889405 or downlink 3060137afd00 to set the current time 2021 – Jan ~-~- 29 Friday 03:03:25
425 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image001.png||alt="IMG_256"]]
424 424  
425 425  
426 -=== 2.5.3 Set Device Time ===
428 +== 2.5 Humidity and Temperature alarm function ==
427 427  
428 428  
429 -User need to set (% style="color:blue" %)**SYNCMOD=1**(%%) to enable sync time via MAC command.
431 +On each sampling define by AT+TR ( default 900s or 15 minutes), when the value exceed the range, it will trigger an Alarm and immediately sends a uplink.
430 430  
431 -Once S31x-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to S31x-LB. If S31x-LB fails to get the time from the server, S31x-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
432 432  
433 -(% style="color:red" %)**Note: LoRaWAN Server need to support LoRaWAN v1.0.3(MAC v1.0.3) or higher to support this MAC command feature, Chirpstack,TTN V3 v3 and loriot support but TTN V3 v2 doesn't support. If server doesn't support this command, it will through away uplink packet with this command, so user will lose the packet with time request for TTN V3 v2 if SYNCMOD=1.**
434 +(% style="color:blue" %)**AT Commands:**
434 434  
436 +(% style="color:#037691" %)**AT+ SHHUM=min,max**
435 435  
436 -=== 2.5.4 Datalog Uplink payload (FPORT~=3) ===
438 +Example: AT+ SHHUM=50,80 ~/~/ Alarm when humidity lower than 50 or higher than 80.
437 437  
438 438  
439 -The Datalog uplinks will use below payload format.
441 +(% style="color:#037691" %)**AT+ SHTEMP=min,max**
440 440  
441 -**Retrieval data payload:**
443 +Example: AT+ SHTEMP=20,30 ~/~/ Alarm when temperature lower than 20 or higher than 30
442 442  
443 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
444 -|=(% style="width: 60px;background-color:#D9E2F3;color:#0070C0" %)(((
445 -**Size(bytes)**
446 -)))|=(% style="width: 40px; background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 55px; background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 65px; background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 180px; background-color:#D9E2F3;color:#0070C0" %)**1**|=(% style="width: 100px; background-color:#D9E2F3;color:#0070C0" %)**4**
447 -|(% style="width:103px" %)Value|(% style="width:68px" %)(((
448 -ignore
449 -)))|(% style="width:104px" %)(((
450 -(((
451 -Humidity
452 -)))
453 453  
454 -(((
455 -
456 -)))
457 -)))|(% style="width:87px" %)(((
458 -Temperature
459 -)))|(% style="width:178px" %)(((
460 -Poll message flag & Alarm Flag& Level of PA8
461 -)))|(% style="width:137px" %)Unix Time Stamp
446 +(% style="color:red" %)**Notice:**
462 462  
463 -**Poll message flag & Alarm Flag & Level of PA8:**
448 +* To disable Alarm, user can set min and max to same value , such as (% style="color:#037691" %)**AT+SHTEMP=0,0.**
464 464  
465 -[[image:image-20230524114302-1.png||height="115" width="736"]]
450 +* If user only want to send only min or max, user can set the alarm to a value that device won’t reach. For example: (% style="color:#037691" %)**AT+SHTEMP=-80,0.**
466 466  
467 467  
468 -**No ACK Message**:  1: This message means this payload is fromn Uplink Message which doesn't get ACK from the server before ( for **PNACKMD=1** feature)
469 469  
470 -**Poll Message Flag**: 1: This message is a poll message reply.
471 471  
472 -* Poll Message Flag is set to 1.
473 473  
474 -* Each data entry is 11 bytes, to save airtime and battery, devices will send max bytes according to the current DR and Frequency bands.
456 +== 2.6 Trggier an uplink by external interrupt ==
475 475  
476 -For example, in US915 band, the max payload for different DR is:
477 477  
478 -**a) DR0:** max is 11 bytes so one entry of data
459 +S31-NB has an external trigger interrupt function. Users can use the PB15 pin to trigger the upload of data packets.
479 479  
480 -**b) DR1:** max is 53 bytes so devices will upload 4 entries of data (total 44 bytes)
461 +(% style="color:blue" %)**AT command:**
481 481  
482 -**c) DR2:** total payload includes 11 entries of data
463 +* (% style="color:#037691" %)**AT+INTMOD **(%%) ~/~/ Set the trigger interrupt mode
483 483  
484 -**d) DR3: **total payload includes 22 entries of data.
465 +* (% style="color:#037691" %)**AT+INTMOD=0 **(%%) ~/~/Disable Interrupt
485 485  
486 -If devise doesn't have any data in the polling time. Device will uplink 11 bytes of 0   
467 +* (% style="color:#037691" %)**AT+INTMOD=1 **(%%) ~/~/Trigger by rising and falling edge
487 487  
488 -**Example:**
469 +* (% style="color:#037691" %)**AT+INTMOD=2 **(%%) ~/~/Trigger by falling edge
489 489  
490 -If S31x-LB has below data inside Flash:
471 +* (% style="color:#037691" %)**AT+INTMOD=3  **(%%) ~/~/Trigger by rising edge
491 491  
492 -[[image:image-20230524114654-2.png]]
493 493  
494 494  
495 -If user sends below downlink command: 31646D84E1646D856C05
496 496  
497 -Where : Start time: 646D84E1 = time 23/5/24 03:30:41
476 += 3. Configure S31x-NB =
498 498  
499 - Stop time: 646D856C= time 23/5/24 03:33:00
478 +== 3.1 Configure Methods ==
500 500  
501 501  
502 -**S31x-LB will uplink this payload.**
481 +S31x-NB supports below configure method:
503 503  
504 -[[image:image-20230524114826-3.png||height="448" width="1244"]]
483 +* AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
505 505  
506 -(((
507 -00 00 02 36 01 10 40 64 6D 84 E1 00 00 02 37 01 10 40 64 6D 84 F8 00 00 02 37 01 0F 40 64 6D 85 04 00 00 02 3A 01 0F 40 64 6D 85 18 00 00 02 3C 01 0F 40 64 6D 85 36 00 00 02 3D 01 0E 40 64 6D 85 3F 00 00 02 3F 01 0E 40 64 6D 85 60 00 00 02 40 01 0E 40 64 6D 85 6A
508 -)))
485 +* AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].
509 509  
510 -(((
511 -Where the first 11 bytes is for the first entry:
512 -)))
487 +* LoRaWAN Downlink.  Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
513 513  
514 -(((
515 -00 00 02 36 01 10 40 64 6D 84 E1
516 -)))
517 517  
518 -(((
519 -**Hum**=0x0236/10=56.6
520 -)))
521 521  
522 -(((
523 -**Temp**=0x0110/10=27.2
524 -)))
525 525  
526 -(((
527 -**poll message flag & Alarm Flag & Level of PA8**=0x40,means reply data,sampling uplink message,the PA8 is low level.
528 -)))
529 -
530 -(((
531 -**Unix time** is 0x646D84E1=1684899041s=23/5/24 03:30:41
532 -)))
533 -
534 -
535 -(% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的(% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的
536 -
537 -== 2.6 Temperature Alarm Feature ==
538 -
539 -
540 -S31x-LB work flow with Alarm feature.
541 -
542 -
543 -[[image:image-20230524110125-3.png||height="768" width="1115"]]
544 -
545 -
546 -
547 -== 2.7 Frequency Plans ==
548 -
549 -
550 -The S31x-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
551 -
552 -[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]
553 -
554 -
555 -== 2.8 ​Firmware Change Log ==
556 -
557 -
558 -**Firmware download link: **[[https:~~/~~/www.dropbox.com/sh/fis3g6nmhv0eokg/AAC6BcCZaX4BdqZkduUvZ3jIa?dl=0>>https://www.dropbox.com/sh/fis3g6nmhv0eokg/AAC6BcCZaX4BdqZkduUvZ3jIa?dl=0]]
559 -
560 -
561 -= 3. Configure S31x-LB =
562 -
563 -== 3.1 Configure Methods ==
564 -
565 -
566 -S31x-LB supports below configure method:
567 -
568 -* AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
569 -* AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].
570 -* LoRaWAN Downlink.  Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
571 -
572 572  == 3.2 General Commands ==
573 573  
574 574  
... ... @@ -836,3 +836,6 @@
836 836  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
837 837  
838 838  * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[Support@dragino.cc>>mailto:Support@dragino.cc]].
759 +
760 +
761 +(% style="display:none" %) (%%)
1692411831805-116.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +94.4 KB
Content
1692413185538-164.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +777.4 KB
Content
1692415924540-357.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +94.4 KB
Content
image-20230819102012-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +239.0 KB
Content
image-20230819102029-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +155.8 KB
Content
image-20230819102136-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +359.4 KB
Content
image-20230819104725-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +583.4 KB
Content
image-20230819104805-5.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +582.8 KB
Content
image-20230819110632-6.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +224.4 KB
Content
image-20230819110702-7.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +53.2 KB
Content
image-20230819113244-10.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +12.0 KB
Content
image-20230819113244-11.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +57.5 KB
Content
image-20230819113244-8.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +13.0 KB
Content
image-20230819113244-9.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +35.5 KB
Content