Changes for page wiki_test

Last modified by Mengting Qiu on 2024/09/05 17:35

From 107.1 to 106.2 From 107.10 to 107.9

From version 107.9

edited by Xiaoling
on 2023/10/11 11:18

Change comment: There is no comment for this version

To version 107.1

edited by Xiaoling
on 2023/10/11 09:38

Change comment: Uploaded new attachment "image-20231011093807-6.png", version {1}

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -15,19 +15,15 @@
  = 1. Introduction =
--== 1.1 What is DS03A-NB NB-IoT Door Sensor ==
++== 1.1 What is SW3L-NB NB-IoT Flow Sensor ==
--The Dragino DS03A-NB is a (% style="color:blue" %) **NB-IoT Door Sensor**(%%) for Internet of Things solution. It (% style="color:blue" %)**detects door open/close status**(%%) and uplinks to IoT server via NB-IoT network. user can see the door status, open duration, open counts in the IoT Server.
++The Dragino SW3L-NB is a (% style="color:blue" %)**NB-IoT Flow Sensor**(%%). It detects water flow volume and uplink to IoT server via NB-IoT network. User can use this to (% style="color:blue" %)**monitor the water usage for buildings**.
--The DS03A-NB will send periodically data every 2 hours as well as for each door open/close action. It also counts the door open times and calculates the last door open duration. Users can also disable the uplink for each open/close event, instead, DS03A-NB can count each open event and uplink periodically.
++The SW3L-NB will send water flow volume every 20 minutes. It can also detect the (% style="color:blue" %)**water flow status and send Alarm**(%%), to avoid the waste for water usage such as broken toilet case.
--DS03A-LB supports (% style="color:blue" %)**Datalog Feature,** (%%)it can save the data when there is no NB-IoT network and uplink when network recover.
++SW3L-NB is designed for both indoor and outdoor use. It has a weatherproof enclosure and industrial level battery to (% style="color:blue" %)**work in low to high temperatures**.
--DS03A-LB has the (% style="color:blue" %)**Open Alarm Feature**,(%%) user can set this feature so the device will send an alarm if the door has been open for a certain time.
--
--DS03A-LB is designed for outdoor use. It has a weatherproof enclosure and industrial level battery to work in low to high temperatures
--
  SW3L-NB supports different uplink methods including (% style="color:blue" %)**MQTT, MQTTs, UDP & TCP**(%%) for different application requirement, and support uplinks to various IoT Servers.
  SW3L-NB (% style="color:blue" %)**supports BLE configure **(%%)and(% style="color:blue" %)** OTA update**(%%) which make user easy to use.
@@ -36,7 +36,7 @@
  SW3L-NB has optional built-in SIM card and default IoT server connection version. Which makes it works with simple configuration.
--[[image:image-20231011093807-6.png||height="278" width="879"]]
++[[image:image-20231010091546-2.png||height="348" width="909"]]
  == 1.2 Features ==
@@ -45,10 +45,7 @@
  * NB-IoT Bands: B1/B2/B3/B4/B5/B8/B12/B13/B17/B18/B19/B20/B25/B28/B66/B70/B85 @H-FDD
  * Ultra-low power consumption
  * Upload water flow volume
--* Door Open/Close detect
--* Door open/close statistics
--* Datalog Feature
--* Open Alarm Feature
++* Monitor water waste
  * Multiply Sampling and one uplink
  * Support Bluetooth v5.1 remote configure and update firmware
  * Uplink on periodically
@@ -56,6 +56,7 @@
  * 8500mAh Battery for long term use
  * Nano SIM card slot for NB-IoT SIM
++
  == 1.3 Specification ==
@@ -105,21 +105,37 @@
  (% style="display:none" %) (%%)
--== 1.4 Applications ==
++== 1.4 Flow Sensor Spec ==
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/1654741400370-813.png?rev=1.1||alt="1654741400370-813.png"]]
++(((
++(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)
++|=(% style="width: 80px;background-color:#4F81BD;color:white" %)**Model**|=(% style="width: 80px;background-color:#4F81BD;color:white" %)**Probe**|=(% style="width: 80px;background-color:#4F81BD;color:white" %)**Diameter**|=(% style="width: 80px;background-color:#4F81BD;color:white" %)**Range**|=(% style="width: 80px;background-color:#4F81BD;color:white" %)**Max Pressure**|=(% style="width: 110px;background-color:#4F81BD;color:white" %)**Measure**
++|(% style="width:88px" %)SW3L-004|(% style="width:75px" %)DW-004|(% style="width:107px" %)G1/2" /DN15|(% style="width:101px" %)1~~30L/min|(% style="width:116px" %)≤ 2.0Mpa|(% style="width:124px" %)450 pulse = 1 L
++|(% style="width:88px" %)SW3L-006|(% style="width:75px" %)DW-006|(% style="width:107px" %)G3/4" /DN20|(% style="width:101px" %)1~~60L/min|(% style="width:116px" %)≤ 1.2Mpa|(% style="width:124px" %)390 pulse = 1 L
++|(% style="width:88px" %)SW3L-010|(% style="width:75px" %)DW-010|(% style="width:107px" %)G 1" /DN25|(% style="width:101px" %)2~~100L/min|(% style="width:116px" %)≤ 2.0Mpa|(% style="width:124px" %)64 pulse = 1 L
++)))
--== 1.5 Sleep mode and working mode ==
++== 1.5 Applications ==
++
++* Flow Sensor application
++* Water Control
++* Toilet Flow Sensor
++* Monitor Waste water
++
++
++== 1.6 Sleep mode and working mode ==
++
++
  (% style="color:blue" %)**Deep Sleep Mode: **(%%)Sensor doesn't have any NB-IoT activate. This mode is used for storage and shipping to save battery life.
  (% style="color:blue" %)**Working Mode:** (%%)In this mode, Sensor will work as NB-IoT Sensor to Join NB-IoT network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.
--== 1.6 Button & LEDs ==
++== 1.7 Button & LEDs ==
  [[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675071855856-879.png]]
@@ -138,9 +138,10 @@
  )))
  |(% style="width:167px" %)Fast press ACT 5 times.|(% style="width:117px" %)Deactivate Device|(% style="width:225px" %)(% style="color:red" %)**Red led**(%%) will solid on for 5 seconds. Means device is in Deep Sleep Mode.
--== 1.7 BLE connection ==
++== 1.8 BLE connection ==
++
  SW3L-NB support BLE remote configure and firmware update.
@@ -153,19 +153,19 @@
  If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.
--== 1.8 Pin Definitions & Switch ==
++== 1.9 Pin Definitions & Switch ==
  [[image:image-20230819104805-5.png]]
--=== 1.8.1 Jumper JP2 ===
++=== 1.9.1 Jumper JP2 ===
  Power on Device when put this jumper.
--=== 1.8.2 BOOT MODE / SW1 ===
++=== 1.9.2 BOOT MODE / SW1 ===
  **1)** (% style="color:blue" %)**ISP**(%%): upgrade mode, device won't have any signal in this mode. but ready for upgrade firmware. LED won't work. Firmware won't run.
@@ -173,7 +173,7 @@
  **2)** (% style="color:blue" %)**Flash**(%%): work mode, device starts to work and send out console output for further debug
--=== 1.8.3 Reset Button ===
++=== 1.9.3 Reset Button ===
  Press to reboot the device.
@@ -181,7 +181,7 @@
  (% style="display:none" %)
--== 1.9 Mechanical ==
++== 1.10 Mechanical ==
  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual/WebHome/1675143884058-338.png?rev=1.1||alt="1675143884058-338.png"]]
@@ -194,20 +194,23 @@
  **Probe Mechanical:**
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LDS03A%20-%20Outdoor%20LoRaWAN%20OpenClose%20Door%20Sensor%20Manual/WebHome/1654741444887-479.png?width=513&height=399&rev=1.1||alt="1654741444887-479.png"]]
++(% style="color:blue" %)**DW-004 Flow Sensor: diameter: G1/2” / DN15.  450 pulse = 1 L**
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/image-20220519091350-1.png?width=722&height=385&rev=1.1||alt="image-20220519091350-1.png"]]
--== 1.10 Magnet Distance ==
++(% style="color:blue" %)**006: DW-006 Flow Sensor: diameter: G3/4” / DN20.  390 pulse = 1 L**
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/image-20220519091423-2.png?width=723&height=258&rev=1.1||alt="image-20220519091423-2.png"]]
--* Wood Door: 10mm ~~ 30mm
--* Iron Door: 30 ~~ 45mm
++(% style="color:blue" %)**010: DW-010 Flow Sensor: diameter: G 1” / DN25.   64 pulse = 1 L**
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/image-20220519091423-3.png?width=724&height=448&rev=1.1||alt="image-20220519091423-3.png"]]
--= 2. Use DS03A-NB to communicate with IoT Server =
++= 2. Use SW3L-NB to communicate with IoT Server =
++
  == 2.1 Send data to IoT server via NB-IoT network ==
@@ -216,7 +216,7 @@
  Below shows the network structure:
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/DS03A-NB_NB-IoT_Door_Sensor_User_Manual/WebHome/image-20231011093807-6.png?width=879&height=278&rev=1.1||alt="image-20231011093807-6.png"]]
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L-NB_NB-IoT_Flow_Sensor_User_Manual/WebHome/image-20231010091546-2.png?width=909&height=348&rev=1.1||alt="image-20231010091546-2.png"]]
  There are two version: (% style="color:blue" %)**-GE**(%%) and (% style="color:blue" %)**-1D**(%%) version of SW3L-NB.
@@ -296,6 +296,7 @@
  * Json entry 1 ~~ 8 are the last 1 ~~ 8 sampling data as specify by (% style="color:#037691" %)**AT+NOUD=8 ** (%%)Command. Each entry includes (from left to right): Water Flow, Sampling time.
++
  === 2.2.2 HEX format Payload(Type~=0) ===
@@ -376,328 +376,326 @@
  == 2.3  Uplink Payload ==
--=== 2.3.2  Sensor Configuration, FPORT~=4 ===
++=== 2.3.1 Sensor Configuration, FPORT~=4 ===
--DS03A-LB will only send this command after getting the downlink command **(0x26 02)** from the server.
++SW3L-NB will only send this command after getting the downlink command **(0x26 02)** from the server.
--(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:515px" %)
--|(% colspan="8" style="background-color:#d9e2f3; color:#0070c0; width:515px" %)**Sensor Configuration FPORT=4**
--|**Size(bytes)**|(% style="width:75px" %)**3**|(% style="width:50px" %)**1**|(% style="width:100px" %)**1**|(% style="width:90px" %)**2**|(% style="width:100px" %)**1**|(% style="width:100px" %)**2**|(% style="width:98px" %)**1**
--|**Value**|(% style="width:75px" %)TDC (unit:sec)|(% style="width:77px" %)Disalarm|(% style="width:96px" %)(((
--Keep status1
--)))|(% style="width:99px" %)(((
--Keep time1(unit: sec)
--)))|(% style="width:87px" %)Keep status2|(% style="width:97px" %)(((
--Keep time2(unit: sec)
--)))|(% style="width:98px" %)(((
--Alarm interval(unit: min)
--)))
++(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
++|(% style="background-color:#4f81bd; color:white; width:70px" %) **Size(bytes)**|(% style="background-color:#4f81bd; color:white; width:105px" %)**3**|(% style="background-color:#4f81bd; color:white; width:60px" %)**1**|(% style="background-color:#4f81bd; color:white; width:96px" %)**1**|(% style="background-color:#4f81bd; color:white; width:105px" %)**2**|(% style="background-color:#4f81bd; color:white; width:74px" %)**1**
++|**Value**|(% style="width:104px" %)TDC(unit:sec)|(% style="width:43px" %)N/A|(% style="width:91px" %)Stop Timer|(% style="width:100px" %)Alarm Timer|(% style="width:69px" %)Reserve
  Example parse in TTNv3
--[[image:image-20230630155527-3.png||height="146" width="902"]]
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L-LB_LoRaWAN_Flow_Sensor_User_Manual/WebHome/image-20230614172555-4.png?width=853&height=151&rev=1.1||alt="image-20230614172555-4.png"]]
--* (((
--(% style="color:blue" %)**TDC: (default: 0x001C20)**
--)))
++* (% style="color:blue" %)**TDC: (default: 0x0004B0)**
--Uplink interval for the Open/Close Event, default value is 0x001C20 which is 7200 seconds = 2 hours.
++Uplink interval for the total pulse count, default value is 0x0004B0 which is 1200 seconds = 20 minutes.
--* (((
--(% style="color:blue" %)**Disalarm: (default: 0)**
--)))
++* (% style="color:blue" %)**STOP Duration & Alarm Timer**
-- **If Disalarm = 1**, DS03A-LB will only send uplink at every TDC periodically. This is normally use for pulse meter application, in this application, there are many open/close event, and platform only care about the total number of pulse.
++Shows the configure value of [[Alarm for continuously water flow>>||anchor="H2.7Alarmforcontinuouslywaterflow"]]
-- **If Disalarm = 0**, DS03A-LB will send uplink at every TDC periodically and send data on each open/close event. This is useful for the application user need to monitor the open/close event in real-time.
++=== 2.3.2 Water Flow Value, Uplink FPORT~=2 ===
--(% style="color:red" %)** Note: When Disalarm=0, a high frequently open/close event will cause lots of uplink and drain battery very fast. **
++(((
++SW3L-NB will send this uplink **after** Device Status once join the NB-IoT network successfully. And SW3L-NB will:
++)))
--* (((
--(% style="color:blue" %)**Keep Status1 & Keep Time1 & Keep Status2 & Keep Time2**
++(((
++periodically send this uplink every 20 minutes, this interval [[can be changed>>||anchor="H2.10SetTransmitIntervalTime"]].
  )))
--Shows the configure value of [[Alarm Base on Timeout Feature>>||anchor="H3.3.3A0AlarmBaseonTimeout"]]
--
--
--
--* (((
--(% style="color:blue" %)**Alarm interval(default: 0)**
++(((
++Uplink Payload totals 11 bytes.
  )))
--When the state of the door sensor has not been changed after the timeout alarm, the device will send a uplink every alarm interval. It will stop the alarm until the state of the door sensor is changed after the timeout alarm.
++(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:515px" %)
++|=(% colspan="6" style="width: 515px; background-color:#4F81BD;color:white" %)**Water Flow Value,  FPORT=2**
++|(% style="width:50px" %)**Size(bytes)**|(% style="width:110px" %)**1**|(% style="width:120px" %)**4**|(% style="width:110px" %)**1**|(% style="width:55px" %)**1**|(% style="width:70px" %)**4**
++|(% style="width:110px" %)**Value**|(% style="width:81px" %)Calculate Flag  & [[Alarm>>||anchor="H2.7Alarmforcontinuouslywaterflow"]]|(% style="width:95px" %)(((
++Total pulse Or Last Pulse
++)))|(% style="width:78px" %)(((
++MOD & PA4_status & PB15_status
++)))|(% style="width:92px" %)Reserve(0x01)|(% style="width:134px" %)Unix TimeStamp
++**Calculate Flag & Alarm:**
--=== 2.3.3  Real-Time Open/Close Status, Uplink FPORT~=2 ===
++(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:500px" %)
++|(% style="background-color:#4f81bd; color:white; width:70px" %)**Size(bit)**|(% style="background-color:#4f81bd; color:white; width:70px" %)**[bit7:bit6]**|(% style="background-color:#4f81bd; color:white; width:90px" %)**[bit5:bit2]**|(% style="background-color:#4f81bd; color:white; width:140px" %)**bit1**|(% style="background-color:#4f81bd; color:white; width:130px" %)**bit0**
++|(% style="width:88px" %)**Value**|(% style="width:117px" %)Reserve|(% style="width:117px" %)Calculate Flag|(% style="width:169px" %)Alarm: 0: No Alarm; 1: Alarm|(% style="width:150px" %)TDC flag 0:No;1:Yes
++**MOD & PA4_status & PB15_status:**
--DS03A-LB will send this uplink **after** Device Status once join the LoRaWAN network successfully. And DS03A-LB will send uplinks when:
++(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:230px" %)
++|(% style="background-color:#4f81bd; color:white; width:50px" %)**Size(bit)**|(% style="background-color:#4f81bd; color:white; width:60px" %)**bit7**|(% style="background-color:#4f81bd; color:white; width:60px" %)**bit6**|(% style="background-color:#4f81bd; color:white; width:60px" %)**[bit5:bit0]**
++|(% style="width:88px" %)**Value**|(% style="width:117px" %)PA4_status|(% style="width:117px" %)PB15_status|(% style="width:118px" %)MOD
--* Every 2 hours, this interval [[can be changed>>||anchor="H3.3.1A0SetTransmitIntervalTime"]].
--* There is an Open/Close event.  (This info can be disabled by AT+DISALARM=1)
++(% style="color:#037691" %)**  **[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L-LB_LoRaWAN_Flow_Sensor_User_Manual/WebHome/image-20230626093242-1.png?width=892&height=276&rev=1.1||alt="image-20230626093242-1.png"]]
--**1) When (% style="color:blue" %)AT+TTRCHANNEL=1(%%), Uplink Payload totals (% style="color:blue" %)11 bytes. (Default mode)(%%)**
--(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:515px" %)
--|=(% colspan="5" style="background-color:#D9E2F3;color:#0070C0;width:515px" %)**Real-Time Open/Close Status, FPORT=2**
--|(% style="width:94px" %)**Size(bytes)**|(% style="width:97px" %)**1**|(% style="width:95px" %)**3**|(% style="width:119px" %)**3**|(% style="width:107px" %)**4**
--|(% style="width:95px" %)**Value**|(% style="width:97px" %)(((
--Status & [[Alarm>>||anchor="H3.3.4A0TTRIG126TTRIG2timeoutstatusalarm"]]
--)))|(% style="width:95px" %)Total open door events|(% style="width:119px" %)(((
--The last door open duration (unit: sec)
--)))|(% style="width:108px" %)[[Unix TimeStamp>>||anchor="H2.5.2UnixTimeStamp"]]
++* (((
++(% style="color:blue" %)**Calculate Flag**
++)))
--**Status & Alarm:**
++(((
++The calculate flag is a user defined field, IoT server can use this flag to handle different meters with different pulse factors. For example, if there are 100 Flow Sensors, meters 1 ~~50 are 1 liter/pulse and meters 51 ~~ 100 has 1.5 liter/pulse.
++)))
--(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:515px" %)
--|(% style="background-color:#d9e2f3; color:#0070c0; width:50px" %)**Size(bit)**|(% style="background-color:#d9e2f3; color:#0070c0; width:60px" %)**[bit7:bit4]**|(% style="background-color:#d9e2f3; color:#0070c0; width:80px" %)**bit3**|(% style="background-color:#d9e2f3; color:#0070c0; width:100px" %)**bit2**|(% style="background-color:#d9e2f3; color:#0070c0; width:120px" %)**bit1**|(% style="background-color:#d9e2f3; color:#0070c0; width:105px" %)**bit0**
--|(% style="width:76px" %)**Value**|(% style="width:96px" %)Reserve|(% style="width:110px" %)(((
--Count mod
--)))|(% style="width:106px" %)TDC flag 0:No;1:Yes|(% style="width:148px" %)(((
--Alarm 0: No Alarm; 1: Alarm
--)))|(% style="width:131px" %)(((
--Status 0: Close; 1: Open
++(((
++**Example: in the default payload:**
  )))
--[[image:image-20230630155451-2.png||height="246" width="928"]]
--
--
  * (((
--(% style="color:blue" %)**Count mod:Default=0**
++calculate flag=0: for SW3L-004 Flow Sensor: 450 pulse = 1 L
  )))
--
--0: Uplink total open door times since factory
--
--1: Uplink total open door times since last FPORT=2 uplink.
--
--
--* (% style="color:blue" %)**TDC flag**
--
--When the flag is 1, it means sending packets at normal time intervals.
--
--Otherwise, it is a packet sent at non-TDC time.
--
--
  * (((
--(% style="color:#0000ff" %)**Alarm**
++calculate flag=1: for SW3L-006 Flow Sensor: 390 pulse = 1 L
  )))
--
--See [[Alarm Base on Timeout>>||anchor="H3.3.3A0AlarmBaseonTimeout"]]
--
--
  * (((
--(% style="color:blue" %)**Status**
++calculate flag=2: for SW3L-010 Flow Sensor: 64 pulse = 1 L
  )))
--This bit is 1 when the door sensor is open and 0 when it is close.
--
--
--* (((
--(% style="color:blue" %)**Total open door events**
++(((
++Default value: 0.
  )))
--Total pulse/counting base on open door.
++(((
++Range (4 bits): (b)0000 ~~ (b) 1111
--Range (3 Bytes) : 0x000000 ~~ 0xFFFFFF . Max: 16777215
++If user use with a meter for example is 0.02L/pulse. To proper decode the correct value in server,
++1) User can set the Calculate Flag of this sensor to 3.
--* (((
--(% style="color:blue" %)**The last door open duration**
++2) In server side, when a sensor data arrive, the decoder will check the value of Calculate Flag, It the value is 3, the total volume = 0.02 x Pulse Count.
  )))
--Door sensor last open duration.
++(((
++(% style="color:red" %)**NOTE: User need to set Calculate Flag to proper value before use Flow Sensor. Downlink or AT Command see: **(%%)Refer: [[Set Calculate Flag>>||anchor="H2.8Setthecalculateflag"]]
--Unit: sec.
++(((
++
++)))
++)))
--[[image:image-20230701094042-1.png||height="154" width="763"]]
++* (((
++(% style="color:blue" %)**Alarm**
++)))
--**2) When (% style="color:blue" %)AT+TTRCHANNEL=2(%%), Uplink Payload totals (% style="color:blue" %)18 bytes(%%)**(% style="color:blue" %).
++(((
++See [[Alarm for continuously water flow>>||anchor="H2.7Alarmforcontinuouslywaterflow"]]
++)))
--(When the maximum DR of some frequencies is 11 bytes, it will cause the server to receive empty packets)
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/image-20220519095946-4.png?width=724&height=65&rev=1.1||alt="image-20220519095946-4.png"]]
--(% style="color:red" %)**Note:When using the AT+TTRCHANNEL=2 command, the Datalog function cannot be used.**
--(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:515px" %)
--|=(% colspan="8" style="background-color:#D9E2F3;color:#0070C0; width: 515px;" %)**Real-Time Open/Close Status, FPORT=2**
--|(% style="width:50px" %)**Size(bytes)**|(% style="width:97px" %)**1**|(% style="width:95px" %)**3**|(% style="width:125px" %)**3**|(% style="width:100px" %)**4**|(% style="width:86px" %)**1**|(% style="width:96px" %)**3**|(% style="width:126px" %)**3**
--|(% style="width:95px" %)**Value**|(% style="width:97px" %)(((
--Status1 & Alarm1
--)))|(% style="width:95px" %)Total open door events1|(% style="width:125px" %)(((
--The last door open duration1 (unit: sec)
--)))|(% style="width:100px" %)[[Unix TimeStamp>>||anchor="H2.5.2UnixTimeStamp"]]|(% style="width:86px" %)(((
--Status2 & Alarm2
--)))|(% style="width:96px" %)Total open door events2|(% style="width:126px" %)The last door open duration2 (unit: sec)
++(((
++* (% style="color:blue" %)**TDC flag**
--**Status1 & Alarm1:**
++When the flag is 1, it means sending packets at normal time intervals.
--(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:514px" %)
--|(% style="background-color:#d9e2f3; color:#0070c0; width:50px" %)**Size(bit)**|(% style="background-color:#d9e2f3; color:#0070c0; width:60px" %)**[bit7:bit4]**|(% style="background-color:#d9e2f3; color:#0070c0; width:70px" %)**bit3**|(% style="background-color:#d9e2f3; color:#0070c0; width:100px" %)**bit2**|(% style="background-color:#d9e2f3; color:#0070c0; width:117px" %)**bit1**|(% style="background-color:#d9e2f3; color:#0070c0; width:117px" %)**bit0**
--|(% style="width:76px" %)**Value**|(% style="width:96px" %)Reserve|(% style="width:99px" %)(((
--Count mod
--)))|(% style="width:103px" %)TDC flag 0:No;1:Yes|(% style="width:216px" %)(((
--Alarm1 0: No Alarm; 1: Alarm (PA8 of pin)
--)))|(% style="width:181px" %)(((
--Status1 0: Close; 1: Open (PA8 of pin)
++Otherwise, it is a packet sent at non-TDC time.
  )))
--**Status2 & Alarm2:**
++* (((
++(% style="color:blue" %)**Total pulse**
++)))
--(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
--|(% style="background-color:#d9e2f3; color:#0070c0; width:50px" %)**Size(bit)**|(% style="background-color:#d9e2f3; color:#0070c0; width:60px" %)**[bit7:bit2]**|(% style="background-color:#d9e2f3; color:#0070c0; width:200px" %)**bit1**|(% style="background-color:#d9e2f3; color:#0070c0; width:200px" %)**bit0**
--|(% style="width:76px" %)**Value**|(% style="width:113px" %)Reserve|(% style="width:219px" %)(((
--Alarm2 0: No Alarm; 1: Alarm (PA4 of pin)
--)))|(% style="width:181px" %)(((
--Status2 0: Close; 1: Open (PA4 of pin)
++(((
++Total pulse/counting since factory
  )))
--[[image:image-20230630155908-6.png||height="295" width="927"]]
++(((
++Range (4 Bytes) : 0x00000000~~ 0xFFFFFFFF .
++
++)))
  * (((
--(% style="color:blue" %)**Count mod:Default=0**
++(% style="color:blue" %)**Last Pulse**
  )))
--0: Uplink total open door times since factory
++(((
++Total pulse since last FPORT=2 uplink. (Default 20 minutes)
++)))
--1: Uplink total open door times since last FPORT=2 uplink.
++(((
++Range (4 Bytes) : 0x00000000~~ 0xFFFFFFFF .
--* (% style="color:blue" %)**TDC flag**
++* (((
++(% style="color:blue" %)**PA4_status: Support digital level input below 3.3V**
++)))
--When the flag is 1, it means sending packets at normal time intervals.
++(((
++0 ~-~-> PA4 is at low level.
++)))
--Otherwise, it is a packet sent at non-TDC time.
++(((
++1 ~-~-> PA4 is at high level.
  * (((
--(% style="color:#0000ff" %)**Alarm1 or Alarm2**
++(% style="color:blue" %)**PB15_status: Support digital level input below 3.3V**
  )))
--See [[Alarm Base on Timeout>>||anchor="H3.3.3A0AlarmBaseonTimeout"]]
++(((
++0 ~-~-> PB15 is at low level.
++)))
++(((
++1 ~-~-> PB15 is at high level..
++)))
++)))
++)))
  * (((
--(% style="color:blue" %)**Status1 **(% style="color:#0000ff" %)**or **(% style="color:blue" %)**Status2**
++(% style="color:blue" %)**MOD: Default =0**
  )))
--This bit is 1 when the door sensor is open and 0 when it is close.
++(((
++MOD=0 ~-~-> Uplink Total Pulse since factory
++)))
++(((
++MOD=1 ~-~-> Uplink total pulse since last FPORT=2 uplink.
++
++)))
++
  * (((
--(% style="color:blue" %)**Total open door events1 **(% style="color:#0000ff" %)**or**(% style="color:blue" %)** Total open door events2**
++(% style="color:blue" %)**Water Flow Value**
  )))
--Total pulse/counting base on open door.
++(((
++**Total Water Flow Volume = (Calculate Flag) x (Total Pulse)=9597/450=21.3L**
++)))
--Range (3 Bytes) : 0x000000 ~~ 0xFFFFFF . Max: 16777215
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/image-20220519095946-5.png?width=727&height=50&rev=1.1||alt="image-20220519095946-5.png"]]
--* (((
--(% style="color:blue" %)**The last door open duration1 **(% style="color:#0000ff" %)**or**(% style="color:blue" %)** The last door open duration2**
++(((
++**Total Water Flow for TDC timer = (Calculate Flag) x (Last Pulse)=79/450=0.2L**
  )))
--Door sensor last open duration.
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L%20LoRaWAN%20Outdoor%20Flow%20Sensor/WebHome/image-20220519095946-6.png?width=733&height=43&rev=1.1||alt="image-20220519095946-6.png"]] **    **
--Unit: sec.
--[[image:image-20230701094042-1.png||height="154" width="763"]]
++=== 2.3.3 Historical Water Flow Status, FPORT~=3 ===
--=== 2.3.4  Historical Door Open/Close Event, FPORT~=3 ===
++(((
++SW3L-NB stores sensor values and users can retrieve these history values via the downlink command.
++)))
++(((
++The historical payload includes one or multiplies entries and every entry has the same payload as Real-Time water flow status.
--DS03A-LB stores sensor values and users can retrieve these history values via the [[downlink command>>||anchor="H2.5DatalogFeature"]].
++(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:515px" %)
++|=(% colspan="6" style="width: 515px; background-color:#4F81BD;color:white" %)**Water Flow Value,  FPORT=3**
++|(% style="width:50px" %)**Size(bytes)**|(% style="width:110px" %)**1**|(% style="width:120px" %)**4**|(% style="width:110px" %)**1**|(% style="width:55px" %)**1**|(% style="width:70px" %)**4**
++|(% style="width:110px" %)**Value**|(% style="width:81px" %)Calculate Flag  & [[Alarm>>||anchor="H2.7Alarmforcontinuouslywaterflow"]]|(% style="width:95px" %)(((
++Total pulse Or Last Pulse
++)))|(% style="width:78px" %)(((
++MOD & PA4_status & PB15_status
++)))|(% style="width:92px" %)Reserve(0x01)|(% style="width:134px" %)Unix TimeStamp
--The historical payload includes one or multiplies entries and every entry has the same payload as Real-Time open/close status.
++**Calculate Flag & Alarm:**
--(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
--|=(% colspan="5" style="background-color:#D9E2F3;color:#0070C0;width:515px" %)**Real-Time Open/Close Status, FPORT=3**
--|(% style="width:60px" %)**Size(bytes)**|(% style="width:80px" %)**1**|(% style="width:120px" %)**3**|(% style="width:150px" %)**3**|(% style="width:90px" %)**4**
--|(% style="width:95px" %)**Value**|(% style="width:97px" %)(((
--Status & [[Alarm>>||anchor="H3.3.3A0AlarmBaseonTimeout"]]
--)))|(% style="width:95px" %)Total open door events|(% style="width:119px" %)(((
--The last door open duration (unit: sec)
--)))|(% style="width:108px" %)[[Unix TimeStamp>>||anchor="H2.5.2UnixTimeStamp"]]
++(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:515px" %)
++|(% style="background-color:#4f81bd; color:white; width:50px" %)**Size(bit)**|(% style="background-color:#4f81bd; color:white; width:89px" %)**bit7**|(% style="background-color:#4f81bd; color:white; width:89px" %)**bit6**|(% style="background-color:#4f81bd; color:white; width:69px" %)**[bit5:bit2]**|(% style="background-color:#4f81bd; color:white; width:129px" %)**bit1**|(% style="background-color:#4f81bd; color:white; width:89px" %)**bit0**
++|(% style="width:88px" %)**Value**|(% style="width:96px" %)(((
++No ACK message
++)))|(% style="width:94px" %)Poll Message Flag|(% style="width:115px" %)Calculate Flag|(% style="width:136px" %)Alarm: 0: No Alarm; 1: Alarm|(% style="width:120px" %)TDC flag 0:No;1:Yes
--**Status & Alarm:**
++**MOD & PA4_status & PB15_status:**
--(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:515px" %)
--|(% style="background-color:#d9e2f3; color:#0070c0; width:50px" %)**Size(bit)**|(% style="background-color:#d9e2f3; color:#0070c0; width:75px" %)**bit7**|(% style="background-color:#d9e2f3; color:#0070c0; width:65px" %)**bit6**|(% style="background-color:#d9e2f3; color:#0070c0; width:50px" %)**[bit5:bit4]**|(% style="background-color:#d9e2f3; color:#0070c0; width:50px" %)**bit3**|(% style="background-color:#d9e2f3; color:#0070c0; width:70px" %)**bit2**|(% style="background-color:#d9e2f3; color:#0070c0; width:80px" %)**bit1**|(% style="background-color:#d9e2f3; color:#0070c0; width:75px" %)**bit0**
--|(% style="width:76px" %)**Value**|(% style="width:88px" %)No ACK message|(% style="width:92px" %)Poll Message Flag|(% style="width:89px" %)Reserve|(% style="width:90px" %)(((
--Count mod
--)))|(% style="width:95px" %)(((
--TDC flag 0:No; 1:Yes
--)))|(% style="width:116px" %)(((
--Alarm 0: No Alarm; 1: Alarm
--)))|(% style="width:112px" %)(((
--Status 0:Close; 1: Open
++(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:240px" %)
++|(% style="background-color:#4f81bd; color:white; width:60px" %)**Size(bit)**|(% style="background-color:#4f81bd; color:white; width:60px" %)**bit7**|(% style="background-color:#4f81bd; color:white; width:60px" %)**bit6**|(% style="background-color:#4f81bd; color:white; width:60px" %)**[bit5:bit0]**
++|(% style="width:88px" %)**Value**|(% style="width:117px" %)PA4_status|(% style="width:117px" %)PB15_status|(% style="width:118px" %)MOD
  )))
  * (((
--Each data entry is 11 bytes and has the same structure as [[Real-Time open/close status>>||anchor="H2.3.3A0Real-TimeOpen2FCloseStatus2CUplinkFPORT3D2"]], to save airtime and battery, DS03A-LB will send max bytes according to the current DR and Frequency bands.
++Each data entry is 11 bytes and has the same structure as [[real time water flow status>>||anchor="H2.3.2A0WaterFlowValue2CUplinkFPORT3D2"]], to save airtime and battery, SW3L will send max bytes according to the current DR and Frequency bands.
  )))
++(((
  For example, in the US915 band, the max payload for different DR is:
++)))
  (((
--**~1. DR0**: max is 11 bytes so one entry of data
++(% style="color:blue" %)**a) DR0:**(%%) max is 11 bytes so one entry of data
  )))
  (((
--**2. DR1**: max is 53 bytes so devices will upload 4 entries of data (total 44 bytes)
++(% style="color:blue" %)**b) DR1:**(%%) max is 53 bytes so devices will upload 4 entries of data (total 44 bytes)
  )))
  (((
--**3. DR2**: total payload includes 11 entries of data
++(% style="color:blue" %)**c) DR2:**(%%) total payload includes 11 entries of data
  )))
  (((
--**4. DR3**: total payload includes 22 entries of data.
++(% style="color:blue" %)**d) DR3:**(%%) total payload includes 22 entries of data.
  )))
--If DS03A-LB doesn't have any data in the polling time. It will uplink 11 bytes of 0
++(((
++If SW3L-NB doesn't have any data in the polling time. It will uplink 11 bytes of 0
--[[image:image-20230630155556-4.png||height="146" width="938"]]
++
++)))
--**Downlink:**
++(((
++(% style="color:#037691" %)**Downlink:**
++)))
--0x31 64 9E 7D 34 64 9E 7E 9C 05
++(((
++0x31 64 92 C5 AC 64 92 C7 8C 05
++)))
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L-LB_LoRaWAN_Flow_Sensor_User_Manual/WebHome/image-20230626093440-2.png?width=890&height=160&rev=1.1||alt="image-20230626093440-2.png"]]
--**Uplink:**
--45 00 00 00 00 00 00 64 9E 7D 48 40 00 00 00 00 00 63 64 9E 7D 9C 41 00 00 01 00 00 63 64 9E 7D A4 40 00 00 01 00 00 8D 64 9E 7E 31 43 00 00 02 00 00 8D 64 9E 7E 44 48 00 00 02 00 00 1F 64 9E 7E 59 4B 00 00 03 00 00 1F 64 9E 7E 6B
++(((
++(% style="color:#037691" %)**Uplink:**
++)))
++(((
++41 00 01 00 00 00 08 64 92 C5 E4 40 00 01 00 00 00 08 64 92 C6 06 49 41 01 00 00 00 00 64 92 C6 8B 49 81 01 00 00 00 00 64 92 C7 34 4A 01 01 00 00 00 2D 64 92 C7 7C
--**Parsed Value:**
++
++)))
--[COUNTMOD, TDC_FLAG, ALARM,  DOOR_STATUS, OPEN_DOOR_TIMES, LAST_DOOR_OPEN_DURATION, TIME]
++(((
++(% style="color:#037691" %)**Parsed Value:**
++)))
++(((
++[TDC_flag, Alarm, Calculate Flag, PA4_status, PB15_status, MOD, Total pulse or Last Pulse,** **Water Flow Value, TIME]
++)))
--[SUM,YES,FALSE,OPEN,0,0,2023-06-30 06:59:20],
--[SUM,NO,FALSE,CLOSE,0,99,2023-06-30 07:00:44],
++(((
++[YES,FALSE,0,L,L, 0,8, 0.0,2023-06-21 09:41:56],
--[SUM,NO,FALSE,OPEN, 1,99,2023-06-30 07:00:52],
++[NO,FALSE,0,L,L, 0,8, 0.0,2023-06-21 09:42:30],
--[SUM,NO,FALSE,CLOSE,1,141,2023-06-30 07:03:13],
++[YES,FALSE,2,L,H,1,0, 0.0,2023-06-21 09:44:43],
--[SUM,NO,TRUE,OPEN, 2,141,2023-06-30 07:03:32],
++[YES,FALSE,2,H,L,1,0, 0.0,2023-06-21 09:47:32],
--[PART,NO,FALSE,CLOSE,2,31,2023-06-30 07:03:53],
++[NO,TRUE ,2, L,L,1,45,0.7,2023-06-21 09:48:44],
++)))
--[PART,NO,TRUE,OPEN, 3,31,2023-06-30 07:04:11],
++[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SW3L-LB_LoRaWAN_Flow_Sensor_User_Manual/WebHome/image-20230626093703-3.png?width=894&height=156&rev=1.1||alt="image-20230626093703-3.png"]]
--[[image:image-20230630172740-1.png||height="199" width="868"]]
--
--
  == 2.4 Test Uplink and Change Update Interval ==
@@ -713,7 +713,7 @@
  == 2.5 Multi-Samplings and One uplink ==
--To save battery life, DS03A-NB will sample Water Flow data every 15 minutes and send one uplink every 2 hours. So each uplink it will include 8 stored data + 1 real-time data. They are defined by:
++To save battery life, SW3L-NB will sample Water Flow data every 15 minutes and send one uplink every 2 hours. So each uplink it will include 8 stored data + 1 real-time data. They are defined by:
  * (% style="color:#037691" %)**AT+TR=900**   (%%)     ~/~/ The unit is seconds, and the default is to record data once every 900 seconds (15 minutes, the minimum can be set to 180 seconds)
@@ -727,7 +727,7 @@
  == 2.6 Trggier an uplink by external interrupt ==
--DS03A-NB has an external trigger interrupt function. Users can use the PB15 pin to trigger the upload of data packets.
++SW3L-NB has an external trigger interrupt function. Users can use the PB15 pin to trigger the upload of data packets.
  (% style="color:blue" %)**AT command:**
@@ -741,6 +741,7 @@
  * (% style="color:#037691" %)**AT+INTMOD=3  **(%%)  ~/~/ Trigger by rising edge
++
  == 2.7 Alarm for continuously water flow ==
@@ -761,7 +761,7 @@
  )))
  (((
--Default: 15s, If DS03A-NB didn't see any water flow in 15s, DS03A-NB will consider stop of water flow event.
++Default: 15s, If SW3L-NB didn't see any water flow in 15s, SW3L-NB will consider stop of water flow event.
  )))
  * (((
@@ -769,7 +769,7 @@
  )))
  (((
--**Example:** 3 minutes, if DS03A-NB detect a start of water flow event and didn't detect a stop event within Alarm timer, DS03A-NB will send an Alarm to indicate a water flow abnormal alarm.
++**Example:** 3 minutes, if SW3L-NB detect a start of water flow event and didn't detect a stop event within Alarm timer, SW3L-NB will send an Alarm to indicate a water flow abnormal alarm.
  )))
  (((
@@ -833,6 +833,7 @@
  * **Example**: 0XA501         ~/~/  Same as AT+CALCFLAG =1
++
  == 2.9 Set count number ==
@@ -851,6 +851,7 @@
  * **Example**: 0xA6000064      ~/~/  Same as AT+ SETCNT =100
++
  == 2.10 Set Transmit Interval Time ==
@@ -896,17 +896,18 @@
  )))
--= 3. Configure DS03A-NB =
++= 3. Configure SW3L-NB =
  == 3.1 Configure Methods ==
--DS03A-NB supports below configure method:
++SW3L-NB supports below configure method:
  * AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
  * AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].
++
  == 3.2 AT Commands Set ==
@@ -990,7 +990,7 @@
  = 4. Battery & Power Consumption =
--DS03A-NB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
++SW3L-NB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
  [[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
@@ -1012,6 +1012,7 @@
  * Update through UART TTL interface : **[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.
++
  = 6. FAQ =
  == 6.1 How can I access t BC660K-GL AT Commands? ==
@@ -1025,7 +1025,7 @@
  = 7. Order Info =
--Part Number: (% style="color:blue" %)**DS03A-NB-XX**
++Part Number: (% style="color:blue" %)**SW3L-NB-XX-YY**
  (% style="color:red" %)**XX**(%%):
@@ -1035,14 +1035,43 @@
  (% style="color:#037691" %)**1NCE SIM Card NB-IoT network coverage**(%%): Austria, Belgium, Bulgaria, Croatia, Czech Republic, Denmark, Finland, Germany, Great Britain, Greece, Hungary, Ireland, Italy, Latvia, Malta, Netherlands, Norway, Puerto Rico, Russia, Slovak , Republic, Slovenia, Spain, Sweden, Switzerland, Taiwan, USA, US Virgin Islands
++(((
++(% style="color:blue" %)**YY**(%%): Flow Sensor Model:
++)))
++(((
++  **004:** DW-004 Flow Sensor: diameter: G1/2” / DN15.  450 pulse = 1 L
++)))
++(((
++  **006:** DW-006 Flow Sensor: diameter: G3/4” / DN20.  390 pulse = 1 L
++)))
++
++(((
++  **010:** DW-010 Flow Sensor: diameter: G 1” / DN25.   64 pulse = 1 L
++)))
++
++* (((
++calculate flag=0: for SW3L-004 Flow Sensor: 450 pulse = 1 L
++)))
++
++* (((
++calculate flag=1: for SW3L-006 Flow Sensor: 390 pulse = 1 L
++)))
++
++* (((
++calculate flag=2: for SW3L-010 Flow Sensor: 64   pulse = 1 L
++
++
++
++)))
++
  = 8. Packing Info =
  (% style="color:#037691" %)**Package Includes**:
--* DS03A-NB NB-IoT Door sensor x 1
++* SW3L-NB NB-IoT Distance Detection sensor x 1
  * External antenna x 1
@@ -1056,6 +1056,7 @@
  * Weight / pcs : 180g
++
  = 9. Support =