Changes for page wiki_test

Last modified by Mengting Qiu on 2024/09/05 17:35

From 107.19 to 107.18 From 108.1 to 107.31

From version 107.31

edited by Xiaoling
on 2023/10/13 09:39

Change comment: There is no comment for this version

To version 107.19

edited by Xiaoling
on 2023/10/11 14:49

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -44,6 +44,7 @@
  * NB-IoT Bands: B1/B2/B3/B4/B5/B8/B12/B13/B17/B18/B19/B20/B25/B28/B66/B70/B85 @H-FDD
  * Ultra-low power consumption
++* Upload water flow volume
  * Door Open/Close detect
  * Door open/close statistics
  * Datalog Feature
@@ -137,9 +137,6 @@
  )))
  |(% style="width:167px" %)Fast press ACT 5 times.|(% style="width:117px" %)Deactivate Device|(% style="width:225px" %)(% style="color:red" %)**Red led**(%%) will solid on for 5 seconds. Means device is in Deep Sleep Mode.
--(% style="color:red" %)**Note: When the device is executing a program, the buttons may become invalid. It is best to press the buttons after the device has completed the program execution.**
--
--
  == 1.7 BLE connection ==
@@ -206,6 +206,7 @@
  * Wood Door: 10mm ~~ 30mm
  * Iron Door: 30 ~~ 45mm
++
  = 2. Use DS03A-NB to communicate with IoT Server =
  == 2.1 Send data to IoT server via NB-IoT network ==
@@ -359,6 +359,7 @@
  [[image:image-20230922094043-2.png||height="558" width="851"]]
++
  === 2.2.4 ThingSpeak Payload(Type~=1) ===
@@ -413,6 +413,7 @@
   **If Disalarm = 0**, DS03A-NB will send uplink at every TDC periodically and send data on each open/close event. This is useful for the application user need to monitor the open/close event in real-time.
++
  (% style="color:red" %)** Note: When Disalarm=0, a high frequently open/close event will cause lots of uplink and drain battery very fast. **
@@ -420,9 +420,10 @@
  (% style="color:blue" %)**Keep Status1 & Keep Time1 & Keep Status2 & Keep Time2**
  )))
--Shows the configure value of [[Alarm Base on Timeout Feature>>||anchor="H2.9AlarmBaseonTimeout"]]
++Shows the configure value of [[Alarm Base on Timeout Feature>>||anchor="H2.9A0AlarmBaseonTimeout"]]
++
  * (((
  (% style="color:blue" %)**Alarm interval(default: 0)**
  )))
@@ -435,7 +435,7 @@
  DS03A-NB will send this uplink **after** Device Status once join the LoRaWAN network successfully. And DS03A-NB will send uplinks when:
--* Every 2 hours, this interval [[can be changed>>||anchor="H2.7SetTransmitIntervalTime"]].
++* Every 2 hours, this interval [[can be changed>>||anchor="H2.7A0SetTransmitIntervalTime"]].
  * There is an Open/Close event.  (This info can be disabled by AT+DISALARM=1)
  **1) When (% style="color:blue" %)AT+TTRCHANNEL=1(%%), Uplink Payload totals (% style="color:blue" %)11 bytes. (Default mode)(%%)**
@@ -444,7 +444,7 @@
  |=(% colspan="5" style="background-color:#4F81BD;color:white;width:515px" %)**Real-Time Open/Close Status, FPORT=2**
  |(% style="width:94px" %)**Size(bytes)**|(% style="width:97px" %)**1**|(% style="width:95px" %)**3**|(% style="width:119px" %)**3**|(% style="width:107px" %)**4**
  |(% style="width:95px" %)**Value**|(% style="width:97px" %)(((
--Status & [[Alarm>>||anchor="2.10TTRIG126TTRIG2timeoutstatusalarm"]]
++Status & [[Alarm>>||anchor="H3.3.4A0TTRIG126TTRIG2timeoutstatusalarm"]]
  )))|(% style="width:95px" %)Total open door events|(% style="width:119px" %)(((
  The last door open duration (unit: sec)
  )))|(% style="width:108px" %)Unix TimeStamp
@@ -576,7 +576,7 @@
  (% style="color:#0000ff" %)**Alarm1 or Alarm2**
  )))
--See [[Alarm Base on Timeout>>||anchor="H2.9AlarmBaseonTimeout"]]
++See [[Alarm Base on Timeout>>||anchor="H2.9A0AlarmBaseonTimeout"]]
  * (((
@@ -603,7 +603,7 @@
  Unit: sec.
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/DS03A-LB/WebHome/image-20230701094042-1.png?width=763&height=154&rev=1.1||alt="image-20230701094042-1.png"]]
++[[image:image-20230701094042-1.png||height="154" width="763"]]
  === 2.3.3  Historical Door Open/Close Event, FPORT~=3 ===
@@ -660,7 +660,7 @@
  If DS03A-NB doesn't have any data in the polling time. It will uplink 11 bytes of 0
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/DS03A-LB/WebHome/image-20230630155556-4.png?width=938&height=146&rev=1.1||alt="image-20230630155556-4.png"]]
++[[image:image-20230630155556-4.png||height="146" width="938"]]
  **Downlink:**
@@ -691,9 +691,10 @@
  [PART,NO,TRUE,OPEN, 3,31,2023-06-30 07:04:11],
--[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/DS03A-LB/WebHome/image-20230630172740-1.png?width=868&height=199&rev=1.1||alt="image-20230630172740-1.png"]]
++[[image:image-20230630172740-1.png||height="199" width="868"]]
++
  == 2.4 Test Uplink and Change Update Interval ==
@@ -737,6 +737,7 @@
  * (% style="color:#037691" %)**AT+INTMOD=3  **(%%)  ~/~/ Trigger by rising edge
++
  == 2.7 Set Transmit Interval Time ==
@@ -777,9 +777,6 @@
  )))
  * (((
  Example 2: Downlink Payload: 0100003C      ~/~/ Set Transmit Interval (TDC) = 60 seconds
--
--
--
  )))
  == 2.8 Enable / Disable Alarm ==
@@ -801,7 +801,7 @@
 xA7 00     ~/~/ Same As AT+DISALARM=0
--== 2.9 Alarm Base on Timeout ==
++== 2.9  Alarm Base on Timeout ==
  DS03A-NB can monitor the timeout for a status change, this feature can be used to monitor some events such as door opening too long etc. Related Parameters are:
@@ -854,6 +854,7 @@
  * (((
  (% style="color:#037691" %)**AT+TTRIG1=0,0**  (%%)  **~-~-> ** Default Value, disable timeout Alarm.
++
  )))
@@ -875,6 +875,7 @@
  * (((
  (% style="color:#037691" %)**AT+TTRIG2=0,0**  (%%)  **~-~-> ** Default Value, disable timeout Alarm.
++
  )))
@@ -970,11 +970,49 @@
  Example:  0D aa => AT+TTRCHANNEL = second byte
--== 2.13  Clear the open door times and the duration of the last open door ==
++== 2.13 Set Time Sync Mode ==
++Feature: Enable/Disable Sync system time via LoRaWAN MAC Command (DeviceTimeReq), LoRaWAN server must support v1.0.3 protocol to reply to this command.
++
++SYNCMOD is set to 1 by default. If user wants to set a different time from the LoRaWAN server, the user needs to set this to 0.
++
  (% style="color:blue" %)**AT Command:**
++(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:500px" %)
++|=(% style="width: 155px;background-color:#4F81BD;color:white" %)**Command Example**|=(% style="width: 288px; background-color:#4F81BD;color:white" %)**Function**|=(% style="width: 57px;background-color:#4F81BD;color:white" %)**Response**
++|(% style="width:155px" %)(((
++AT+SYNCMOD=1
++)))|(% style="width:259px" %)(((
++Enable Sync system time via LoRaWAN MAC Command (DeviceTimeReq) The default is zero time zone.
++)))|(% style="width:44px" %)(((
++OK
++)))
++|(% style="width:155px" %)(((
++AT+SYNCMOD=1,8
++)))|(% style="width:259px" %)(((
++Enable Sync system time via LoRaWAN MAC Command (DeviceTimeReq) Set to East eight time zone.
++)))|(% style="width:44px" %)(((
++OK
++)))
++|(% style="width:155px" %)AT+SYNCMOD=1,-12|(% style="width:259px" %)Enable Sync system time via LoRaWAN MAC Command (DeviceTimeReq) Set to West Twelve Time Zone.|(% style="width:44px" %)OK
++
++(% style="color:blue" %)**Downlink Command:**
++
++0x28 01           ~/~/ Same As AT+SYNCMOD=1
++
++0x28 01 08      ~/~/ Same As AT+SYNCMOD=1,8
++
++0x28 01 F4      ~/~/ Same As AT+SYNCMOD=1,-12
++
++0x28 00           ~/~/ Same As AT+SYNCMOD=0
++
++
++== 2.14  Clear the open door times and the duration of the last open door ==
++
++
++(% style="color:blue" %)**AT Command:**
++
  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
  |=(% style="width: 163px;background-color:#4F81BD;color:white" %)**Command Example**|=(% style="width: 290px; background-color:#4F81BD;color:white" %)**Function**|=(% style="width: 57px;background-color:#4F81BD;color:white" %)**Response**
  |(% style="width:155px" %)AT+CLRC|(% style="width:259px" %)clear the open door times and the duration of the last open door.|(% style="width:44px" %)(((
@@ -986,7 +986,7 @@
  The sensor will clear the open door times and the duration of the last open door.
--== 2.14  Set the count value of the number of open door ==
++== 2.15  Set the count value of the number of open door ==
  (% style="color:blue" %)**AT Command:**
@@ -1126,7 +1126,7 @@
  * Fix bugs.
--Firmware and changelog can be downloaded from : **[[Firmware download link>>https://www.dropbox.com/sh/zbsm9p4coksqwd5/AADy2ZJc39KsvfbhTMCUGmz1a?dl=0]]**
++Firmware and changelog can be downloaded from : **[[Firmware download link>>https://www.dropbox.com/sh/l0bszumyrmil3yv/AAAg8LYGeAgDsD_ycCnweD72a?dl=0]]**
  Methods to Update Firmware:
@@ -1158,6 +1158,7 @@
  (% style="color:#037691" %)**1NCE SIM Card NB-IoT network coverage**(%%): Austria, Belgium, Bulgaria, Croatia, Czech Republic, Denmark, Finland, Germany, Great Britain, Greece, Hungary, Ireland, Italy, Latvia, Malta, Netherlands, Norway, Puerto Rico, Russia, Slovak , Republic, Slovenia, Spain, Sweden, Switzerland, Taiwan, USA, US Virgin Islands
++
  = 8. Packing Info =

Changes for page wiki_test

Summary

Details

Applications

Navigation