Skip to Content
Last modified by Xiaoling on 2025/04/23 15:57
From version 30.8
edited by Xiaoling
on 2022/06/02 09:37
Change comment: There is no comment for this version
To version 32.3
edited by Xiaoling
on 2022/06/02 09:39
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -906,7 +906,7 @@
906 906  
907 907  
908 908  
909 -==== Fast command to handle MODBUS device ====
909 +==== **Fast command to handle MODBUS device** ====
910 910  
911 911  AT+MBFUN is valid since v1.3 firmware version. The command is for fast configure to read Modbus devices. It is only valid for the devices which follow the [[MODBUS-RTU protocol>>url:https://www.modbustools.com/modbus.html]].
912 912  
... ... @@ -913,31 +913,33 @@
913 913  This command is valid since v1.3 firmware version
914 914  
915 915  
916 -AT+MBFUN has only two value:
916 +**AT+MBFUN has only two value:**
917 917  
918 -* AT+MBFUN=1: Enable Modbus reading. And get response base on the MODBUS return
918 +* **AT+MBFUN=1**: Enable Modbus reading. And get response base on the MODBUS return
919 919  
920 920  AT+MBFUN=1, device can auto read the Modbus function code: 01, 02, 03 or 04. AT+MBFUN has lower priority vs AT+DATACUT command. If AT+DATACUT command is configured, AT+MBFUN will be ignore.
921 921  
922 -* AT+MBFUN=0: Disable Modbus fast reading.
922 +* **AT+MBFUN=0**: Disable Modbus fast reading.
923 923  
924 -Example:
925 925  
925 +**Example:**
926 +
926 926  * AT+MBFUN=1 and AT+DATACUT1/AT+DATACUT2 are not configure (0,0,0).
927 927  * AT+COMMAND1= 01 03 00 10 00 08,1 ~-~-> read slave address 01 , function code 03, start address 00 01, quantity of registers 00 08.
928 928  * AT+COMMAND2= 01 02 00 40 00 10,1 ~-~-> read slave address 01 , function code 02, start address 00 40, quantity of inputs 00 10.
929 929  
930 -[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image025.png]]
931 +[[image:1654133913295-597.png]]
931 931  
932 932  
933 -[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image026.png]]
934 +[[image:1654133954153-643.png]]
934 934  
935 935  
936 -* Downlink Commands:
937 +* **Downlink Commands:**
937 937  
938 -A9 aa -à Same as AT+MBFUN=aa
939 +**A9 aa** ~-~-> Same as AT+MBFUN=aa
939 939  
940 940  
942 +
941 941  ==== RS485 command timeout ====
942 942  
943 943  Some Modbus device has slow action to send replies. This command is used to configure the RS485-BL to use longer time to wait for their action.
1654133913295-597.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +116.2 KB
Content
1654133954153-643.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +91.2 KB
Content