Skip to Content
Last modified by Bei Jinggeng on 2025/09/03 16:12
From version 252.2
edited by Mengting Qiu
on 2025/01/20 13:40
Change comment: There is no comment for this version
To version 252.3
edited by Mengting Qiu
on 2025/01/20 13:42
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -671,7 +671,7 @@
671 671  
672 672  * AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
673 673  
674 -* AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].
674 +* AT Command via UART Connection : See [[UART Connection>>https://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.4UARTConnectionforRS485-BLbasemotherboard]].
675 675  
676 676  * NB-Iot Downlink.  Instruction for different platforms: See [[NB-Iot downlink>>https://wiki.dragino.com/xwiki/bin/view/Main/General%20Configure%20to%20Connect%20to%20IoT%20server%20for%20-NB%20%26%20-NS%20NB-IoT%20models/#H4.A0MQTT2FUDP2FTCPdownlink]] section.
677 677  
... ... @@ -709,6 +709,8 @@
709 709  * Example 1: Downlink Payload: 0100001E  ~/~/  Set Transmit Interval (TDC) = 30 seconds
710 710  * Example 2: Downlink Payload: 0100003C  ~/~/  Set Transmit Interval (TDC) = 60 seconds
711 711  
712 +
713 +
712 712  === 3.3.2 Set the CO2 or PM mode ===
713 713  
714 714  
... ... @@ -733,6 +733,8 @@
733 733  * 0xE101     Same as: AT+PMMOD=1
734 734  * 0xE100     Same as: AT+PMMOD=0
735 735  
738 +
739 +
736 736  === 3.3.3 Add or Delete RS485 Sensor ===
737 737  
738 738  
... ... @@ -828,6 +828,8 @@
828 828  
829 829  * 0xE5FF  
830 830  
835 +
836 +
831 831  === 3.3.4 RS485 Test Command ===
832 832  
833 833  
... ... @@ -848,6 +848,8 @@
848 848  
849 849  * 0xE20103000001840A     Same as: AT+RSWRITE=0103000001840A
850 850  
857 +
858 +
851 851  === 3.3.5 RS485 response timeout ===
852 852  
853 853  
... ... @@ -870,6 +870,8 @@
870 870  * Example 1: Downlink Payload: E0000005  ~/~/  Set Transmit Interval (DTR) = 5 seconds
871 871  * Example 2: Downlink Payload: E000000A  ~/~/  Set Transmit Interval (DTR) = 10 seconds
872 872  
881 +
882 +
873 873  === 3.3.6 Set or get the total count value ===
874 874  
875 875  
... ... @@ -889,6 +889,8 @@
889 889  
890 890  * Example 1: Downlink Payload: 09000003E8  ~/~/  Set the value to start counting from 1000 = 1000 (times)
891 891  
902 +
903 +
892 892  === 3.3.7  Set interrupt or counting mode ===
893 893  
894 894  
... ... @@ -911,6 +911,8 @@
911 911  
912 912  * Example 1: Downlink Payload: 10 00  ~/~/  Same as: AT+COUNTMOD=0  set to interrupt mode
913 913  
926 +
927 +
914 914  === 3.3.8 Domain name resolution settings ===
915 915  
916 916