Skip to Content
Last modified by Xiaoling on 2025/04/27 16:48
From version 66.4
edited by Xiaoling
on 2022/10/09 16:01
Change comment: There is no comment for this version
To version 43.1
edited by Xiaoling
on 2022/09/30 10:06
Change comment: Uploaded new attachment "1664503611848-385.png", version {1}

Summary

Details

Page properties
Content
... ... @@ -1,13 +7,6 @@
1 -(% style="text-align:center" %)
2 -[[image:1664505654417-133.png]]
3 -
4 -
5 -
6 -
7 7  (% class="wikigeneratedid" %)
8 8  **Table of Contents:**
9 9  
10 -{{toc/}}
11 11  
12 12  
13 13  
... ... @@ -14,10 +14,9 @@
14 14  
15 15  = 1.  Introduction =
16 16  
10 +== 1.1  OverView ==
17 17  
18 -== 1.1  What is TrackerD ==
19 19  
20 -
21 21  (((
22 22  TrackerD is an (% style="color:blue" %)**Open Source LoRaWAN Tracker**(%%) based on (% style="color:blue" %)**ESP32 MCU**(%%) and (% style="color:blue" %)**Semtech LoRa Wireless Chip**.
23 23  )))
... ... @@ -25,14 +25,10 @@
25 25  (((
26 26  In TrackerD, there are various sensors such as GPS, WiFi, BLE, Temperature, Humidity, Motion Detection, and Buzzer. User can use TrackerD for different tracking scenario.
27 27  
28 -(((
29 29  TrackerD is program friendly. Developers can use Arduino IDE to customize the software of TrackerD to fit their IoT solution.
30 -)))
31 31  
32 -(((
33 33  The LoRa wireless technology used in TrackerD allows the user to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption. It targets professional tracking services.
34 34  )))
35 -)))
36 36  
37 37  (((
38 38  TrackerD is equipped with a (% style="color:blue" %)**1000mAh Li-on rechargeable battery**(%%). Each TrackerD has a worldwide unique OTAA keys to join the LoRaWAN network.
... ... @@ -46,7 +46,6 @@
46 46  (% style="color:red" %)**Note: LoRaWAN server can be a general LoRaWAN server other than TTN.**
47 47  
48 48  
49 -
50 50  == 1.2 Specifications ==
51 51  
52 52  
... ... @@ -61,11 +61,13 @@
61 61  * EEPROM: 520 KB
62 62  * Clock Speed: 32Mhz
63 63  
51 +
64 64  (% style="color:blue" %)**Common DC Characteristics:**
65 65  
66 66  * Supply Voltage: 5V via USB port or Internal li-on battery
67 67  * Operating Temperature: -40 ~~ 60°C
68 68  
57 +
69 69  (% style="color:blue" %)**LoRa Spec:**
70 70  
71 71  * Frequency Range,
... ... @@ -87,10 +87,12 @@
87 87  * Packet engine up to 256 bytes with CRC.
88 88  * LoRaWAN 1.0.3 Specification
89 89  
79 +
90 90  (% style="color:blue" %)**Battery:**
91 91  
92 92  * 1000mA Li-on Battery power (for model TrackerD)
93 93  
84 +
94 94  (% style="color:blue" %)**Power Consumption**
95 95  
96 96  * Sleeping Mode: 200uA
... ... @@ -99,6 +99,7 @@
99 99  
100 100  
101 101  
93 +
102 102  == 1.3  Features ==
103 103  
104 104  
... ... @@ -105,7 +105,7 @@
105 105  * LoRaWAN 1.0.3 Class A
106 106  * ESP32 PICO D4
107 107  * SX1276/78 Wireless Chip
108 -* Arduino IDE Compatible
100 +* Arduino IDE Compatible
109 109  * Open source hardware / software
110 110  * Regular/ Real-time GPS,BLE,WIFI tracking
111 111  * Built-in3 axis accelerometer (LIS3DH)
... ... @@ -127,9 +127,9 @@
127 127  
128 128  
129 129  
122 +
130 130  = 2.1 Use TrackerD =
131 131  
132 -
133 133  == 2.1 How it works? ==
134 134  
135 135  
... ... @@ -136,618 +136,490 @@
136 136  TrackerD is configured as LoRaWAN OTAA Class A GPS tracker by default. It has OTAA keys to join LoRaWAN network. To connect a LoRaWAN network, user need to input the OTAA keys in the LoRaWAN IoT server and push reset button of TrackerD (next to USB port). TrackerD will wake up and auto join the network via OTAA.
137 137  
138 138  
139 -
140 140  == 2.2 Quick guide to connect to LoRaWAN server ==
141 141  
133 +Here is an example for how to join the [[TTNv3 LoRaWAN Network>>url:https://eu1.cloud.thethings.network]]. Below is the network structure, we use LPS8N as LoRaWAN gateway in this example.
142 142  
143 -Here is an example for how to join the [[TTNv3 LoRaWAN Network>>url:https://eu1.cloud.thethings.network]]. Below is the network structure, we use LPS8N as LoRaWAN gateway in this example. 
144 144  
136 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image001.png]]
145 145  
146 -[[image:1664501652064-326.png]]
147 147  
148 -
149 -
150 150  The LPS8N is already set to connect to [[TTN V3 network >>url:https://eu1.cloud.thethings.network/]]. What the rest need to is register this device in TTN V3:
151 151  
141 +**(% style="color:blue" %)Step 1**:(%%) Create a device in TTN V3 with the OTAA keys from TrackerD.
152 152  
153 -(% style="color:blue" %)**Step 1**:(%%) Create a device in TTN V3 with the OTAA keys from TrackerD.
154 -
155 155  Each TrackerD is shipped with a sticker with the default device EUI as below:
156 156  
145 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image002.png]]
157 157  
158 -[[image:1664501677253-891.png]]
159 159  
160 160  
149 +
161 161  Input these keys to their LoRaWAN Server portal. Below is TTN V3 screen shot:
162 162  
163 163  
164 -**__Add APP EUI in the application:__**
153 +Add APP EUI in the application
165 165  
155 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image003.png]]
166 166  
167 -[[image:1664501711466-918.png]]
157 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image004.png]]
168 168  
169 169  
160 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image005.png]]
170 170  
171 -[[image:1664501721248-725.png]]
172 172  
173 173  
174 -[[image:1664501734705-405.png]]
164 +Add APP KEY and DEV EUI
175 175  
166 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image006.png]]
176 176  
177 177  
178 -**__Add APP KEY and DEV EUI:__**
179 179  
180 180  
181 -[[image:1664501784668-703.png]]
171 +**(% style="color:blue" %)Step 2**:(%%) Power on TrackerD by using the on board switch.
182 182  
183 183  
174 +**(% style="color:blue" %)Step 3:**(%%) TrackerD will auto join to the LoRaWAN network. After join success, TrackerD will start to upload message to IoT server.
184 184  
185 185  
186 -(% style="color:blue" %)**Step 2**:(%%) Power on TrackerD by using the on board switch.
177 +**(% style="color:blue" %)Positioning Mode(SMOD):**
187 187  
179 +* **GPS ONLY(Factory Settings): **only get GPS location info.
180 +* **BLE ONLY: **Only obtain iBeacon info via BLE. Design for Indoor tracking.
181 +* **GPS/BLE Hybrid: **Combination for Indoor and Outdoor tracking.
188 188  
189 -(% style="color:blue" %)**Step 3:**(%%) TrackerD will auto join to the LoRaWAN network. After join success, TrackerD will start to upload message to IoT server.
183 +User can switch modes by [[changing SMOD>>path:#Positioning_Mode]].
190 190  
191 191  
192 -== 2.3  Positioning Mode(SMOD) ==
186 +== 2.3 Uplink Payload ~-~-~-~-~-~-~-~-~-~-~-~-~-~- ==
193 193  
194 194  
195 -Users can set TrackerD to different Positioning Mode for different applications. Below mod are supported.
189 +=== 2.3.1 Uplink FPORT=5, Device Status ===
196 196  
197 -* (% style="color:#037691" %)**GPS ONLY(Factory Settings):    **(%%)only get and uplink GPS location info.
198 -* (% style="color:#037691" %)**BLE ONLY:              **(%%)Only obtain iBeacon info via BLE and uplink. Design for Indoor tracking.
199 -* (% style="color:#037691" %)**GPS/BLE Hybrid:   **(%%)Combination for Indoor and Outdoor tracking.Devices will try to search BLE iBeacon first. If device can't find the iBeacon, it will use GPS for positioning.
200 200  
201 -Users can switch modes by [[changing SMOD>>||anchor="H3.2.7SetPositioningMode"]].
202 202  
193 +=== 2.3.2 Uplink FPORT= , Realtime GNSS Positioning ===
203 203  
195 +The default uplink payload includes totally 11 bytes. (User can use AT+MOD=0 to enable the Temperature and humidity sensor to hum/tem info from accelerometer. When accelerometer info is enable, total payload will be 15 bytes, please note 15 bytes won’t work on DR0 on US915/AU915 frequency band. )
204 204  
205 -== 2.4  Uplink Payload ==
206 206  
198 +|(((
199 +**Size**
207 207  
208 -=== 2.4.1 Uplink FPORT~=5, Device Status ===
201 +**(bytes)**
202 +)))|4|4|2|1|(((
203 +2
209 209  
210 -
211 -Uplink the device configures with FPORT=5. Once LGT92 Joined the network, it will uplink this message to the server. After first uplink, LHT52 will uplink Device Status every 12 hours.
212 -
213 -
214 -(% border="1.5" style="background-color:#ffffcc; color:green; width:520px" %)
215 -|=(% scope="row" style="width: 108px;" %)**Size(bytes)**|=(% style="width: 82px;" %)**1**|=(% style="width: 83px;" %)**2**|=(% style="width: 94px;" %)**1**|=(% style="width: 84px;" %)**1**|=(% style="width: 44px;" %)2|=(% style="width: 63px;" %)**2**|=(% style="width: 60px;" %)1
216 -|=(% style="width: 108px;" %)**Value**|(% style="width:82px" %)Sensor Model|(% style="width:83px" %)Firmware Version|(% style="width:94px" %)Frequency Band|(% style="width:84px" %)Sub-band|(% style="width:44px" %)BAT|(% style="width:63px" %)SMOD|(% style="width:60px" %)Status
217 -
218 -[[image:1665301570342-765.png]]
219 -
220 -
221 -Example Payload (FPort=5):  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT52%20-%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220621105116-11.png?rev=1.1||alt="image-20220621105116-11.png"]]
222 -
223 -**Sensor Model**: For TrackerD, this value is 0x13.
224 -
225 -**Firmware Version**: 0x0100, Means: v1.0.0 version.
226 -
227 -**Frequency Band**:
228 -
229 -*0x01: EU868
230 -
231 -*0x02: US915
232 -
233 -*0x03: IN865
234 -
235 -*0x04: AU915
236 -
237 -*0x05: KZ865
238 -
239 -*0x06: RU864
240 -
241 -*0x07: AS923
242 -
243 -*0x08: AS923-1
244 -
245 -*0x09: AS923-2
246 -
247 -*0x0a: AS923-3
248 -
249 -**Sub-Band**: value 0x00 ~~ 0x08(only for CN470, AU915,US915. Others are0x00)
250 -
251 -**BAT**: shows the battery voltage for TrackerD.
252 -
253 -Ex1: 0x0B3A = 2874mV
254 -
255 -Use can also get the Device Status uplink through the downlink command:
256 -
257 -
258 -
259 -=== 2.4.2 Uplink FPORT~=2, Realtime GNSS Positioning + Temperature & Humidity ===
260 -
261 -
262 -User can use **AT+SMOD=1,0** to enable uploading on-board Temperature and humidity values, and the total payload will be 15 bytes, please note that 15 bytes won't work on DR0 on US915/AU915 frequency band.
263 -
264 -
265 -(% border="1.2" cellspacing="3" style="background-color:#ffffcc; color:green; width:480px" %)
266 -|=(% scope="row" style="width: 50px;" %)(((
267 -**Size(bytes)**
268 -)))|(% style="width:60px" %)4|(% style="width:70px" %)4|(% style="width:80px" %)2|(% style="width:73px" %)1|(% style="width:40px" %)(((
205 +(optional )
206 +)))|(((
269 269  2
270 -)))|(% style="width:87px" %)(((
271 -2
208 +
209 +(optional)
272 272  )))
273 -|=(% style="width: 69px;" %)**Value**|(% style="width:76px" %)[[Latitude>>||anchor="HLocationinfo:"]]|(% style="width:87px" %)[[Longitude>>||anchor="HLocationinfo:"]]|(% style="width:76px" %)(((
274 -[[Alarm & BAT>>||anchor="HAlarm26BAT:"]]
275 -)))|(% style="width:73px" %)[[FLAG>>||anchor="HFLAG:"]]|(% style="width:40px" %)[[Hum>>||anchor="HHum:"]]|(% style="width:87px" %)[[Tem>>||anchor="HTem:"]]
211 +|**Value**|[[Latitude>>path:#Location]]|[[Longitude>>path:#Location]]|(((
212 +[[Alarm &>>path:#Alarm]]
276 276  
277 -[[image:1665301636888-168.png]]
214 +[[BAT>>path:#Alarm]]
215 +)))|[[FLAG>>path:#Flag]]|Hum|[[Tem>>path:#Pitch]]
278 278  
279 279  
280 -==== (% style="color:blue" %)**Alarm & BAT:**(%%) ====
218 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image007.png]]
281 281  
282 -(% border="1.2" cellspacing="3" style="background-color:#ffffcc; color:green; width:250px" %)
283 -|=(% scope="row" style="width: 50px;" %)**Size(bit)**|(% style="width:50px" %)1 bit|(% style="width:80px" %)1bit|(% style="width:50px" %)14bits
284 -|=(% style="width: 72px;" %)**Value**|(% style="width:67px" %)reserve|(% style="width:118px" %)Alarm Indicate|(% style="width:63px" %)[[BAT>>||anchor="HBAT:"]] 
285 285  
286 -==== (% style="color:blue" %)**FLAG:**(%%) ====
221 +**Alarm & BAT:**
287 287  
288 -(% border="1.2" cellspacing="3" style="background-color:#ffffcc; color:green; width:250px" %)
289 -|=(% scope="row" style="width: 50px;" %)**Size(bit)**|(% style="width:50px" %)2bits|(% style="width:50px" %)1bit
290 -|=(% style="width: 79px;" %)**Value**|(% style="width:55px" %)[[MOD>>||anchor="H3.2.7SetPositioningMode"]]|(% style="width:47px" %)[[LON>>||anchor="HLON:"]]
223 +|**Size(bit)**|1 bit|1bit|14 bits
224 +|**Value**|reserve|Alarm Indicate|[[BAT>>path:#BAT]]
291 291  
292 -**Example:** Payload: 0x02863D68 FAC29BAF 4B45 60 0202 011A 
226 +**FLAG:**
293 293  
228 +|**Size(bit)**|2 bits|1bit|5 bits
229 +|**Value**|[[MOD>>path:#MD]]|[[LON>>path:#LON]]|Firmware version
294 294  
295 -==== (% style="color:blue" %)**Location info:**(%%) ====
296 296  
297 -* Latitude: 02863D68  ⇒  //if (0x//02863D68//& 0x80000000 = 0 )~://  //value = 02863D68 /1000000 = 42.351976//
298 -* Longitude: FAC29BAF  ⇒ //if (0x//FAC29BAF// & 0x80000000 = 1 )~://  //value = (0x//FAC29BAF// – 0x 100000000)/1000000 =//-87.9094//57//
299 299  
300 -(% style="color:red" %)**Important note:**
233 +**Example: Payload: 0x02863D68 FAC29BAF 4B45 60 0202 011A **
301 301  
302 -1.  When power is low (<2.84v), GPS won't be able to get location info and GPS feature will be disabled and the location field will be filled with 0x0FFFFFFF, 0x0FFFFFFF.
303 303  
304 -2.  In this mode, the total payload will be 15 bytes, while US915/AU915 DR0 accepts only 11 bytes payload. In this case, the payload on server will be ignore and shows as below:
236 +**Location info:**
305 305  
238 +* Latitude: 02863D68⇒ //if (0x//02863D68//& 0x80000000 = 0 )~://
306 306  
307 -[[image:1664502116362-706.png]]
240 +//value = 02863D68 /1000000 = 42.351976//
308 308  
242 +* Longitude: FAC29BAF ⇒ //if (0x//FAC29BAF// & 0x80000000 = 1 )~://
309 309  
310 -3.  While GPS can't get location info after timeout(FTIME Parameter), the latitude and longitude will be filled with all 0x00:
244 +//value = (0x//FAC29BAF// – 0x 100000000)/1000000 =//-87.9094//57//
311 311  
312 -[[image:1664502166010-515.png]]
313 313  
247 +Important note:
314 314  
249 +1. When power is low (<2.84v), GPS won’t be able to get location info and GPS feature will be disabled and the location field will be filled with 0x0FFFFFFF, 0x0FFFFFFF.
250 +1. In firmware version v1.5, Roll & Pitch is disabled by default.
251 +1. When enable 9-axis motion sensor, the total payload will be 15 bytes, while US915/AU915 DR0 accept only 11 bytes payload. In this case, the payload on server will be ignore and shows as below:
315 315  
316 -==== (% style="color:blue" %)**Alarm:**(%%) ====
253 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image008.png]]
317 317  
318 -Example:  0x4B & 0x40 >> 6 = 0x01
319 319  
256 +1. While GPS can’t get location info after timeout(FTIME Parameter), the latitude and longitude will be filled with all 0x00:
320 320  
321 -==== (% style="color:blue" %)**BAT:**(%%) ====
258 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image009.png]]
322 322  
323 -Example:  0x0CDD & 0x3FFF ⇒ 3293 (mV).
260 +* **Alarm**: Example: 0x4B & 0x40 >> 6 = 0x01
261 +* **BAT**: Example: 0x0CDD & 0x3FFF ⇒ 3293 (mV).
324 324  
325 -(((
326 -The battery info shows the battery voltage, User can use the below mapping to indicate the battery in percentage: \
327 -)))
263 +The battery info shows the current voltage, for **TrackerD** version which powered by li-on battery. User can use below mapping to indicate the battery in percentage: \
328 328  
329 -* > 4.0v :  80% ~~ 100%
330 -* 3.85v ~~3.99v:  60% ~~ 80%
331 -* 3.70v ~~ 3.84v:  40% ~~ 60%
332 -* 3.40v ~~ 3.69v:  20% ~~ 40%
333 -* < 3.39v:  0~~20%
334 334  
335 -==== (% style="color:blue" %)**LON:**(%%) ====
266 +* > 4.0v : 80% ~~ 100%
267 +* 3.85v ~~3.99v: 60% ~~ 80%
268 +* 3.70v ~~ 3.84v: 40% ~~ 60%
269 +* 3.40v ~~ 3.69v: 20% ~~ 40%
270 +* < 3.39v: 0~~20%
336 336  
337 -Enable/Disable LED activity for uplink
338 338  
339 -(((
340 -0x00:  Disable LED indicator.
341 -)))
273 +* **LON: **Enable/Disable LED activity for uplink
342 342  
343 -(((
344 -0x01:  Enable LED indicator (Default Value)
345 -)))
275 +0x00: Disable LED indicator.
346 346  
277 +0x01: Enable LED indicator (Default Value)
347 347  
348 -==== (% style="color:blue" %)**Hum:**(%%) ====
349 349  
350 -0202 = //if (0x0202 & 0x8000 = 0 ):  value =// 0x0202 / 100 = +514 ⇒ 51.4 degree
280 +* **Hum**: 0202 = //if (0x0202 & 0x8000 = 0 ): value =// 0x0202 / 100 = +514 ⇒ 51.4 degree
281 +* **//Tem//**//: 011A =if (0x011A & 0x8000 = 1 ): value =( 0x011A - 0x10000)/10(dec) ⇒ -//28.2 degree
351 351  
352 352  
353 -==== (% style="color:blue" %)**Tem:**(%%) ====
354 354  
355 -011A =if (0x011A & 0x8000 = 1 ):  value =( 0x011A - 0x10000)/10(dec) ⇒ -//28.2 degree//
285 +=== 2.3.3 Uplink FPORT= , History GNSS Positioning ===
356 356  
357 357  
358 358  
359 -=== 2.4.3  Uplink FPORT~=3, Realtime GNSS Positioning (Default Mode) ===
289 +=== 2.3.4 BLE positioning Payload(Fport=2) ===
360 360  
291 +Different MODE has different payload:
361 361  
362 -The default uplink payload includes totally 11 bytes. The payload is the first 11 bytes of Uplink FPORT=2, real-time GNSS positioning, (remove the temp and humidity)
293 +**MODE=2**
363 363  
295 +|(((
296 +**Size**
364 364  
365 -(% border="1.2" cellspacing="3" style="background-color:#ffffcc; color:green; width:480px" %)
366 -|=(% scope="row" style="width: 50px;" %)(((
367 -**Size(bytes)**
368 -)))|(% style="width:60px" %)4|(% style="width:70px" %)4|(% style="width:80px" %)2|(% style="width:73px" %)1
369 -|=(% style="width: 69px;" %)**Value**|(% style="width:76px" %)[[Latitude>>||anchor="HLocationinfo:"]]|(% style="width:87px" %)[[Longitude>>||anchor="HLocationinfo:"]]|(% style="width:76px" %)(((
370 -[[Alarm & BAT>>||anchor="HAlarm26BAT:"]]
371 -)))|(% style="width:73px" %)[[FLAG>>||anchor="HFLAG:"]]
298 +**(bytes)**
299 +)))|16|4|4|2|4|2|1
300 +|**Value**|[[UUID>>path:#Location]]|(((
301 +iBeacon
372 372  
373 -(% class="wikigeneratedid" %)
374 -[[image:1665301687277-443.png]]
303 +MAJOR
304 +)))|(((
305 +iBeacon
375 375  
307 +MINOR
308 +)))|(((
309 +iBeacon Measured
376 376  
311 +Power
312 +)))|(((
313 +iBeacon
377 377  
378 -=== 2.4.4  Uplink FPORT~=4, History GNSS Positioning ===
315 +RSSI
316 +)))|(((
317 +[[Alarm &>>path:#Alarm]]
379 379  
319 +[[BAT>>path:#Alarm]]
320 +)))|[[FLAG>>path:#Flag]]
380 380  
381 -Set [[PNACKMD=1>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/#H4.13AutoSendNone-ACKmessages]], and TrackerD will wait for ACK for every uplink, when there is no LoRaWAN network, TrackerD will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
382 382  
323 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image010.png]]
383 383  
384 -(% style="color:red" %)**Note for this mode:**
385 385  
386 -* a) TrackerD will do an ACK check for data records sending to make sure every data arrive server.
387 -* b) TrackerD will send data in (% style="color:blue" %)**CONFIRMED Mode**(%%) when PNACKMD=1, but TrackerD won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink, if TrackerD gets an ACK, TrackerD will consider there is a network connection and resend all NONE-ACK Messages.
326 +* **BAT**: Ex1: 0x4B45 & 0x3FFF ⇒ 3901 (mV).
327 +* **MODE: **Define the payload format.
328 +* **UUID: **The uuid from the strongest iBeacon.
329 +* **MAJOR**: The MAJOR from the strongest iBeacon.
330 +* **MINOR**: The MAJOR from the strongest iBeacon.
331 +* **Measured** **Power**: The Measured Power from the strongest iBeacon.
332 +* **RSSI**: The RSSI from the strongest iBeacon.
388 388  
389 -The payload is 15 bytes, as below.
390 390  
391 -(% border="1.5" style="background-color:#ffffcc; color:green; width:520px" %)
392 -|=(% scope="row" %)(((
393 -**Size(bytes)**
394 -)))|4|4|2|1|1|1|1|1
395 -|=**Value**|Latitude|Longitude|Year|Month|Day|Hous|Min|Sen
396 396  
397 -[[image:1665301786397-168.png]]
336 +=== 2.3.5 Add Payload format in TTN V3 ===
398 398  
399 -
400 -
401 -=== 2.4.5  Uplink FPORT~=6, BLE Positioning with Strongest iBeacon ===
402 -
403 -
404 -(% border="1.5" cellspacing="3" style="background-color:#ffffcc; color:green; width:450px" %)
405 -|=(% scope="row" style="width: 60px;" %)(((
406 -**Size(bytes)**
407 -)))|(% style="width:30px" %)16|(% style="width:50px" %)4|(% style="width:50px" %)4|(% style="width:120px" %)2|(% style="width:50px" %)4|(% style="width:50px" %)2|(% style="width:30px" %)1
408 -|=(% style="width: 50px;" %)**Value**|(% style="width:44px" %)[[UUID>>||anchor="HLocationinfo:"]]|(% style="width:61px" %)(((
409 -iBeacon MAJOR
410 -)))|(% style="width:63px" %)(((
411 -iBeacon MINOR
412 -)))|(% style="width:71px" %)(((
413 -iBeacon Measured Power
414 -)))|(% style="width:50px" %)(((
415 -iBeacon RSSI
416 -)))|(% style="width:47px" %)(((
417 -[[Alarm & BAT>>||anchor="HAlarm26BAT:"]]
418 -)))|(% style="width:15px" %)[[FLAG>>||anchor="HFLAG:"]]
419 -
420 -[[image:1664502425687-834.png]]
421 -
422 -
423 -* (% style="color:#037691" %)**BAT: ** (%%) Ex1: 0x4B45 & 0x3FFF ⇒ 3901 (mV).
424 -* (% style="color:#037691" %)**MODE:   **(%%)Define the payload format.
425 -* (% style="color:#037691" %)**UUID:     **(%%)The uuid from the strongest iBeacon.
426 -* (% style="color:#037691" %)**MAJOR:** (%%) The MAJOR from the strongest iBeacon.
427 -* (% style="color:#037691" %)**MINOR:**  (%%)The MAJOR from the strongest iBeacon.
428 -* (% style="color:#037691" %)**Measured Power: ** (%%) The Measured Power from the strongest iBeacon.
429 -* (% style="color:#037691" %)**RSSI:  ** (%%) The RSSI from the strongest iBeacon.
430 -
431 -=== 2.4.5 Add Payload format in TTN V3 ===
432 -
433 -
434 434  In TTN V3, use can add a custom payload so it shows friendly.
435 435  
436 -In the page (% style="color:#037691" %)**Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder**
340 +In the page Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder
437 437  
342 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image011.png]]
438 438  
439 -[[image:1664502649601-895.png]]
440 -
441 -
442 442  Add the decoder from this link:
443 443  
444 444  
445 445  Save the change the uplink message will be parsed. As below:
446 446  
447 -[[image:1664502676891-606.png]]
349 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image012.png]]
448 448  
449 449  
450 450  
451 -== 2.5 Integrate with Datacake ==
452 452  
453 453  
454 -(((
455 -After TrackerD sends data to LoRaWAN server such as TTN, use can pass the data to Datacake and plot out, currently only support GPS plot.
456 -)))
355 +== 2.4 Integrate with Datacake ==
457 457  
458 -(((
459 -Instruction is here:  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20Data%20Cake/#H7.Example~~-~~-AddTrackerDGPSTrackingInDataCake>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20Data%20Cake/#H7.Example--AddTrackerDGPSTrackingInDataCake]]
460 -)))
461 461  
358 +After TrackerD sends data to LoRaWAN server such as TTN, use can pass the data to Datacake and plot out, currently only support GPS plot.
462 462  
463 -[[image:1664502695771-538.png]]
360 +Instruction is here: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20Data%20Cake/#H7.Example~~-~~-AddTrackerDGPSTrackingInDataCake>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20Data%20Cake/#H7.Example--AddTrackerDGPSTrackingInDataCake]]
464 464  
362 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image013.png]]
465 465  
466 466  
467 -== 2.6 Integrate with Tago ==
365 +== 2.5 Integrate with Tago ==
468 468  
469 469  
470 -(((
471 471  After TrackerD sends data to LoRaWAN server such as TTN, use can pass the data to Datacake and plot out, currently only support GPS plot.
472 -)))
473 473  
474 -(((
475 475  Instruction is here: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Tago.IO/#H3.A0Example-CreateTrackerD2FLGT92positioningwidget>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Tago.IO/#H3.A0Example-CreateTrackerD2FLGT92positioningwidget]]
476 -)))
477 477  
372 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image014.png]]
478 478  
479 -[[image:1664502715371-321.png]]
480 480  
481 481  
482 482  
483 -== 2.7 Datalog Feature ==
377 +== 2.6 Alarm Mode ==
484 484  
485 -total 273 entries,by default disable
486 486  
487 -== 2.8 Alarm Mode ==
380 +User can push the **RED button** by more than 5 seconds to enter Alarm Mode.
488 488  
489 489  
490 -(((
491 -User can push the (% style="color:red" %)**RED button**(%%) by more than 5 seconds to enter Alarm Mode.
492 -)))
383 +Once enter Alarm mode, the **GREEN LED** will flash 3 times, the buzzer will alarm for 5 seconds, then TrackerD will immediately send a packet without location info and then send a data packet with GPS positioning information. After that, the device will send 60 packets at 1-minute intervals. The Alarm flag in the payload will be set for the next 60 packets unless exit alert mode.
493 493  
494 494  
495 -(((
496 -Once enter Alarm mode, the (% style="color:green" %)**GREEN LED**(%%) will flash 3 times, the buzzer will alarm for 5 seconds, then TrackerD will immediately send a packet without location info and then send a data packet with GPS positioning information. After that, the device will send 60 packets at 1-minute intervals. The Alarm flag in the payload will be set for the next 60 packets unless exit alert mode.
497 -)))
498 -
499 -
500 -(((
501 501  Two ways to exit alarm mode:
502 -)))
503 503  
504 504  * Server send a downlink command to exit.
505 505  * User fast press the RED button 10 times.
506 506  
507 -(((
508 -When exit alarm mode, (% style="color:red" %)**RED LED**(%%) will light up for 5 seconds, indicating that the alarm mode is exited. And the alert flag will be set to false.
509 -)))
391 +When exit alarm mode, **RED LED** will light up for 5 seconds, indicating that the alarm mode is exited. And the alert flag will be set to false.
510 510  
511 511  
394 +== 2.7 Sports Mode ~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-- ==
512 512  
513 -== 2.9 Transport Mode ==
514 514  
515 515  
516 -In Transport Mode, TrackerD will check if there is motion. If there is no motion, device will send uplinks every 20 minutes. If there is motion, device will send uplink every 5 minutes.
398 +== 2.8 LED Status ==
517 517  
518 518  
519 -== 2.10 LED Status ==
401 +|**Event**|**Action**|**AT+LON to control on/off**
402 +|**Power On**|**BLUE, RED , Green** flash once|N/A
403 +|**Join request**|**Green** led fast blink once (200ms)|Yes
404 +|**Join Success**|**Green** led on 5 second|N/A
405 +|**Fixing Location**|**BLUE **blinks 200ms per second|Yes
406 +|**Fixed and uplink**|**GREEN **blinks twice (200ms per blink)|Yes
407 +|**Fail Fix and uplink**|**RED **blinks twice (200ms per blink)|Yes
408 +|**Enter Alarm mode**|**RED **on for 3 seconds|Yes
409 +|**Uplink under Alarm**|**RED **on for 1 second|Yes
410 +|**Exit Alarm**|**BLUE **led on 5 second|Yes
411 +|**Get Downlink**|**GREEN** led on 1 second|Yes
412 +|**Movement Detect**|**RED **on 500ms|N/A
520 520  
521 521  
522 -(% border="1.5" style="background-color:#ffffcc; color:green; width:500px" %)
523 -|=(% style="width: 150px;" %)**Event**|=(% style="width: 200px;" %)**Action**|=(% style="width: 150px;" %)**AT+LON to control on/off**
524 -|(% style="width:157px" %)**Power On**|(% style="width:271px" %)(% style="color:blue" %)**BLUE, **(% style="color:red" %)**RED , **(% style="color:green" %)**Green** flash once|(% style="width:202px" %)N/A
525 -|(% style="width:157px" %)**Join request**|(% style="width:271px" %)(% style="color:green" %)**Green** (%%)led fast blink once (200ms)|(% style="width:202px" %)Yes
526 -|(% style="width:157px" %)**Join Success**|(% style="width:271px" %)(% style="color:green" %)**Green**(%%) led on 5 second|(% style="width:202px" %)N/A
527 -|(% style="width:157px" %)**Fixing Location**|(% style="width:271px" %)(% style="color:blue" %)**BLUE **(%%)blinks 200ms per second|(% style="width:202px" %)Yes
528 -|(% style="width:157px" %)**Fixed and uplink**|(% style="width:271px" %)(% style="color:green" %)**GREEN ***(%%)***blinks twice (200ms per blink)**|(% style="width:202px" %)Yes
529 -|(% style="width:157px" %)**Fail Fix and uplink**|(% style="width:271px" %)(% style="color:red" %)**RED **(%%)blinks twice (200ms per blink)|(% style="width:202px" %)Yes
530 -|(% style="width:157px" %)**Enter Alarm mode**|(% style="width:271px" %)(% style="color:red" %)**RED **(%%)on for 3 seconds|(% style="width:202px" %)Yes
531 -|(% style="width:157px" %)**Uplink under Alarm**|(% style="width:271px" %)(% style="color:red" %)**RED **(%%)on for 1 second|(% style="width:202px" %)Yes
532 -|(% style="width:157px" %)**Exit Alarm**|(% style="width:271px" %)(% style="color:blue" %)**BLUE **(%%)led on 5 second|(% style="width:202px" %)Yes
533 -|(% style="width:157px" %)**Get Downlink**|(% style="width:271px" %)(% style="color:green" %)**GREEN**(%%) led on 1 second|(% style="width:202px" %)Yes
534 -|(% style="width:157px" %)**Movement Detect**|(% style="width:271px" %)(% style="color:red" %)**RED **(%%)led on 500ms|(% style="width:202px" %)N/A
535 535  
536 -== 2.11 Button Function ==
537 537  
538 538  
539 -(% style="color:blue" %)**RESET button:**
418 +== 2.9 Button Function ==
540 540  
541 -[[image:1664502835802-546.png]]
420 +**RESET button:**
542 542  
422 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image015.png]]
423 +
543 543  Push this button will reboot the device. Device will exit alarm mode and re-join to LoRaWAN server.
544 544  
545 545  
546 -(% style="color:red" %)**RED button:**
427 +**RED button:**
547 547  
548 -[[image:1664502854406-763.png]]
429 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image016.png]]
549 549  
431 +|**Function**|**Action**|**Description**
432 +|Send Alarm|Keep Pressing **RED** button for more than 5 seconds|Enter Alarm Mode.  See [[Alarm Mode>>path:#Alarm_Mode]]
433 +|Exit Alarm Mode|Fast press the **RED** button 10 times|Exit Alarm Mode
434 +|Enter Deep Sleep Mode|Press and hold the button for 10 seconds, then quickly press the device 3 times to enter deep sleep|This is the mode ship out from factory. CPU will be complete in sleep mode and no LoRa activity, only use before deploy.
550 550  
551 -(% border="1.5" style="background-color:#ffffcc; color:green; width:520px" %)
552 -|=(% style="width: 100px;" %)**Function**|=(% style="width: 210px;" %)**Action**|=(% style="width: 210px;" %)**Description**
553 -|(% style="width:135px" %)Send Alarm|(% style="width:220px" %)Keep Pressing (% style="color:red" %)**RED**(%%) button for more than 5 seconds|(% style="width:265px" %)Enter Alarm Mode.  See [[Alarm Mode>>||anchor="H2.6AlarmMode"]]
554 -|(% style="width:135px" %)Exit Alarm Mode|(% style="width:220px" %)Fast press the (% style="color:red" %)**RED** (%%)button 10 times|(% style="width:265px" %)Exit Alarm Mode
555 -|(% style="width:135px" %)Enter Deep Sleep Mode|(% style="width:220px" %)Press and hold the button for 10 seconds, then quickly press the device 3 times to enter deep sleep|(% style="width:265px" %)This is the mode ship out from factory. CPU will be complete in sleep mode and no LoRa activity, only use before deploy.
556 556  
557 -== 2.12 USB Port Function ==
558 558  
559 559  
439 +== 2.10 USB Port Function ==
440 +
560 560  The USB interface of TrackerD has below functions:
561 561  
562 562  * Power on the device
563 563  * Recharge the battery
564 -* [[Configure Device>>||anchor="H3.ConfigureTrackerDviaATcommandorLoRaWANdownlink"]]
565 -* [[Upgrade Firmware>>||anchor="H5.UploadFirmware"]]
445 +* [[Configure Device>>path:#AT_Command]]
446 +* [[Upgrade Firmware>>path:#upgrade_image]]
566 566  
567 -= 3. Configure TrackerD via AT command or LoRaWAN downlink =
568 568  
569 569  
570 -User can configure TrackerD via AT Command or LoRaWAN Downlink.
571 571  
572 -LoRaWAN Downlink instruction for different platforms:  [[IoT LoRaWAN Server>>doc:Main.WebHome]]
573 573  
452 += 3. Configure TrackerD via AT command or LoRaWAN downlink =
574 574  
575 575  
576 -== 3.1 Access AT Command ==
455 +User can configure TrackerD via AT Command or LoRaWAN Downlink.
577 577  
457 +LoRaWAN Downlink instruction for different platforms: [[IoT LoRaWAN Server>>url:http://wiki.dragino.com/xwiki/bin/view/Main/]]
578 578  
579 -TrackerD supports the AT command set in stock firmware. User can connect to TrackerD with TYPE-C cable to use AT commands as shown below.
580 580  
460 +== 3.1 Access AT Command ==
581 581  
582 -[[image:1664502999401-486.png]]
462 +TrackerD supports the AT command set in stock firmware. User can connect to TrackerD with TYPE-C cable to use AT commands as shown below. ...
583 583  
464 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image017.png]]
584 584  
585 -In PC, User needs to set serial tool baud rate to (% style="color:green" %)**115200**(%%) to access serial console for TrackerD. TrackerD will output system info once power on and user will be able to send AT commands:
586 586  
467 +In PC, User needs to set serial tool baud rate to **115200** to access serial console for TrackerD. TrackerD will output system info once power on and user will be able to send AT commands:
587 587  
588 -[[image:1664503022490-662.png]]
589 589  
470 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image018.png]]
590 590  
591 591  
592 -[[image:1664503035713-500.png]]
593 593  
474 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image019.png]]
594 594  
476 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image020.png]]
595 595  
596 -[[image:1664503047675-651.png]]
597 597  
598 -
599 -
600 600  == 3.2 Command Set ==
601 601  
602 602  
603 603  === 3.2.1 Set Transmit Interval ===
604 604  
605 -
606 606  Set device uplink interval.
607 607  
608 -* (% style="color:blue" %)**AT Command:**
486 +* AT Command:
609 609  
610 -(% style="color:#037691" %)**AT+TDC=xxx **
488 +AT+TDC=xxx
611 611  
612 -Example:  AT+TDC=300000. Means set interval to 5 minutes(300 seconds)
490 +Example: AT+TDC=300000. Means set interval to 5 minutes(300 seconds)
613 613  
614 614  
615 -* (% style="color:blue" %)**Downlink Payload (prefix 0x01):**
493 +* Downlink Payload (prefix 0x01):
616 616  
617 -(% style="color:#037691" %)**0x01 00 01 2C**  (%%) ~/~/  Same as AT+TDC=300000
495 +0x01 00 01 2C     ~/~/ Same as AT+TDC=300000
618 618  
619 619  
620 -
621 621  === 3.2.2 Set Alarm Packet transmission interval ===
622 622  
623 -
624 624  Set alarm packet transmit interval
625 625  
626 -* (% style="color:blue" %)**AT Command:**
502 +* AT Command:
627 627  
628 -(% style="color:#037691" %)**AT+ATDC=xx. **
504 +AT+ATDC=xx.
629 629  
630 -Example:  AT+ATDC=60000  **~-~->    ** Set Alarm Packet Interval to 60 seconds. TrackerD will send every 60 seconds in Alarm mode, Default Value: 60000
506 +Example: AT+ATDC=60000  à Set Alarm Packet Interval to 60 seconds. TrackerD will send every 60 seconds in Alarm mode, Default Value: 60000
631 631  
632 632  
633 -* (% style="color:blue" %)**Downlink Payload (prefix 0xB1):**
509 +* Downlink Payload (prefix 0xB1):
634 634  
635 -(% style="color:#037691" %)**0xB1 00 00 3C ** (%%) ~/~/  Same as AT+ATDC=60000
511 +0xB1 00 00 3C    ~/~/Same as AT+ATDC=60000
636 636  
637 637  
514 +=== 3.3.3 Set Sports Mode Packet transmission interval ===
638 638  
639 -=== 3.2.3 Set Transport Mode Packet transmission interval ===
516 +Set sports packet transmit interval
640 640  
518 +* AT Command:
641 641  
642 -Set Transport Mode packet transmit interval
520 +AT+MTDC=xx.
643 643  
644 -* (% style="color:blue" %)**AT Command:**
522 + Example: AT+MTDC=300000  à Set Sports Mode Packet Interval to 300 seconds. TrackerD will send every 300 seconds in Sports mode, Default Value: 300000
645 645  
646 -(% style="color:#037691" %)**AT+MTDC=xx. **
647 647  
648 -Example:  AT+MTDC=300000  **~-~->    ** Set Transport Mode Packet Interval to 300 seconds. TrackerD will send every 300 seconds in Transport mode, Default Value: 300000
525 +* Downlink Payload (prefix 0x03):
649 649  
527 +0x03 00 01 2C    ~/~/Same as AT+ MTDC=3000000
650 650  
651 -* (% style="color:blue" %)**Downlink Payload (prefix 0x03):**
652 652  
653 -(% style="color:#037691" %)**0x03 00 01 2C**  (%%) ~/~/  Same as AT+ MTDC=3000000
654 654  
531 +=== 3.3.4 Exit Alarm ===
655 655  
656 -
657 -=== 3.2.4 Exit Alarm ===
658 -
659 -
660 660  Server send downlink command to exit Alarm mode
661 661  
662 -* (% style="color:blue" %)**AT Command: No AT Command**
535 +* AT Command:
663 663  
664 -* (% style="color:blue" %)**Downlink Payload (prefix 0x02):**
537 +No AT Command
665 665  
666 -(% style="color:#037691" %)**0x02 01**    (%%) ~/~/  Exit Alarm Mode
667 667  
540 +* Downlink Payload (prefix 0x02):
668 668  
542 +0x02 01     ~/~/ Exit Alarm Mode
669 669  
670 -=== 3.2.5 Disable/Enable LED flash ===
671 671  
545 +=== 3.3.5 Disable/Enable LED flash ===
672 672  
673 673  Disable/Enable LED for position, downlink and uplink
674 674  
675 -* (% style="color:blue" %)**AT Command:**
549 +* AT Command:
676 676  
677 -(% style="color:#037691" %)**AT+LON=xx.  (Disable (0), Enable (1), default:1)**
551 +AT+LON=xx.  (Disable (0), Enable (1), default:1)
678 678  
679 -Example: AT+LON=0  **~-~-> ** Disable LED for position, downlink and uplink.
553 + Example: AT+LON=0 à Disable LED for position, downlink and uplink.
680 680  
681 681  
682 -* (% style="color:blue" %)**Downlink Payload (prefix 0xAE):**
556 +* Downlink Payload (prefix 0xAE):
683 683  
684 -(% style="color:#037691" %)**0xAE 00 ** (%%) ~/~/  Same as AT+LON=0
558 +0xAE 00    ~/~/Same as AT+LON=0
685 685  
686 686  
687 687  
688 -=== 3.2.6 Disable/Enable Transport Mode ===
689 689  
563 +=== 3.3.6 Disable/Enable movement detect (Debug Only) ===
690 690  
691 -Users can use this feature to enable/disable Transport Mode.
565 +User can use this feature to check and set thread hole of movement detect
692 692  
693 -* (% style="color:blue" %)**AT Command:**
567 +* AT Command:
694 694  
695 -(% style="color:#037691" %)**AT+INTWK=xx.  (Disable (0), Enable (1), default:0)**
569 +AT+INTWK=xx.  (Disable (0), Enable (1), default:0)
696 696  
697 -Example:  AT+ INTWK =1  **~-~->   ** Enable Transport Mode.
571 + Example: AT+ INTWK =1 à Enable detect movement.
698 698  
699 699  
700 -* (% style="color:blue" %)**Downlink Payload (prefix 0xAF):**
574 +* Downlink Payload (prefix 0xAF):
701 701  
702 -(% style="color:#037691" %)**0xAF 01 ** (%%) ~/~/  Same as AT+ INTWK =1
576 +0xAF 01    ~/~/Same as AT+ INTWK =1
703 703  
704 704  
705 705  
706 -=== 3.2.7 Set Positioning Mode ===
580 +=== 3.3.7 Set Positioning Mode ===
707 707  
582 +SMOD define the how TrackerD scan and uplink date.
708 708  
709 -SMOD define the how TrackerD scan and uplink data:
584 +GPS室外定位模式：设备默认模式，设备入网后会发送device当前模式下的信息，随后立即定位发送数据包（默认是3分钟定位，超过将发送无效数据），如果出现意外情况下，快速按键3下，将会发出报警消息（默认每分钟发送一次）。GPS还有一种logdata模式，在断网的情况下将数据存储下来，等到有网的时候，一次将数据以每10秒上报。
710 710  
586 + BLE室内定位模式：设备入网后会发送device当前模式下的信息，随后立即定位发送数据包（默认是5秒，超过将发送无效数据），如果出现意外情况下，快速按键3下，将会发出报警消息（默认每3分钟发送一次）。
711 711  
712 -* (% style="color:blue" %)**AT Command:**
588 + GPS和BLE混动模式：设备入网后会发送device当前模式下的信息，随后立即判断是否在室内，如果是就进行BLE定位，不是就GPS定位。如果出现意外情况下，快速按键3下，将会发出报警消息（默认每分钟发送一次）。
713 713  
714 -(% style="color:#037691" %)**AT+SMOD=aa,bb**
590 +运动模式：设备入网后会发送device当前模式下的信息，随后发送GPS定位数据，设备判断是否在运动，没有运动传感器没有检测到动作，立即进入静止状态（默认20分钟），如果产生运动，将每5分钟发送一次数据，再第五分钟后检测设备有误运动，无将切换到静止状态，有立即发送数据。
715 715  
716 -(% style="color:#037691" %)** aa:**
717 717  
718 -* (% style="color:#037691" %)**1: GPS ONLY(Factory Settings):    **(%%)only get and uplink GPS location info.
719 -* (% style="color:#037691" %)**2: BLE ONLY:              **(%%)Only obtain iBeacon info via BLE and uplink. Design for Indoor tracking.
720 -* (% style="color:#037691" %)**3: GPS/BLE Hybrid:   **(%%)Combination for Indoor and Outdoor tracking.Devices will try to search BLE iBeacon first. If device can't find the iBeacon, it will use GPS for positioning
721 721  
722 -(% style="color:#037691" %)**bb:**
723 723  
724 -(% style="color:#037691" %)** if aa = 1: **
595 +* AT Command:
725 725  
726 -* (% style="color:#037691" %)**0 :  **(%%)GPS+ BAT+ State+Tem&Hum
727 -* (% style="color:#037691" %)**1 :**(%%)  GPS +BAT State
597 +AT+SMOD=xx.
728 728  
729 -(% style="color:#037691" %)** if aa = 2: **
599 + Example:
730 730  
731 -* (% style="color:#037691" %)**3 :  **(%%)(iBeacon)UUID+ Major + Minor+Power+Rssi+BAT+State
601 + AT+ SMOD =1,0    à GPS+ BAT+ State+Tem&Hum
732 732  
733 - **Example:**
603 + AT+ SMOD =1,1    à GPS +BAT State
734 734  
735 - AT+ SMOD =1,0  **~-~-> ** GPS+ BAT+ State+Tem&Hum
605 + AT+ SMOD =2,3    à (iBeacon)UUID+ Major + Minor+Power+Rssi+BAT+State。
736 736  
737 - AT+ SMOD =1,1    **~-~->**  GPS +BAT State
738 738  
739 - AT+ SMOD =2,3    **~-~->**  (iBeacon)UUID+ Major + Minor+Power+Rssi+BAT+State
608 +* Downlink Payload (prefix 0xA5):
740 740  
610 +0xA5 01 00     ~/~/ Same as AT+ SMOD =1,0
741 741  
742 -* (% style="color:blue" %)**Downlink Payload (prefix 0xA5):**
743 743  
744 -(% style="color:#037691" %)**0xA5 01 00**    (%%) ~/~/  Same as AT+ SMOD =1,0
613 +=== 3.3.8 Set MAX GPS position time ===
745 745  
746 -
747 -
748 -=== 3.2.8 Set MAX GPS position time ===
749 -
750 -
751 751  Set max positioning time, default is 150 seconds. TrackerD will try to get location info within this period. If fail to get position data within this time, TrackerD will use 000000 for latitude and longitude.
752 752  
753 753  
... ... @@ -754,60 +754,60 @@
754 754  If AT+FTIME=0. The GPS module will be always powered and positioning. This will highly increase the power consumption (up to 50mA). When AT+FTIME=0, it will improve fix accuracy and shorten the acquire time for next uplink.
755 755  
756 756  
757 -* (% style="color:blue" %)**AT Command:**
621 +* AT Command:
758 758  
759 -(% style="color:#037691" %)**AT+FTIME=xx**  (%%) **~-~-> ** Set to use xx as max fix time.
623 +AT+FTIME=xx  à Set to use xx as max fix time.
760 760  
761 -Example:  AT+FTIME=150
625 +Example: AT+FTIME=150
762 762  
763 763  
764 -* (% style="color:blue" %)**Downlink Payload (prefix 0xAA):**
628 +* Downlink Payload (prefix 0xAA):
765 765  
766 -(% style="color:#037691" %)**0xAA 00 96 ** (%%) ~/~/  Set AT+FTIME=150
630 +0xAA 00 96      ~/~/Set AT+FTIME=150
767 767  
768 768  
769 769  
634 +
770 770  === 3.3.9 Set PDOP value for GPS fix accuracy ===
771 771  
637 +PDOP(Position Dilution of Precision) filter, TrackerD will only accept GPS data with a lower PDOP value than pre-configure PDOP value. If device can’t get a valid GPS packet within FTIME timeout, it will use the GPS data with lowest PDOP value to server.
772 772  
773 -PDOP(Position Dilution of Precision) filter, TrackerD will only accept GPS data with a lower PDOP value than pre-configure PDOP value. If device can't get a valid GPS packet within FTIME timeout, it will use the GPS data with lowest PDOP value to server.
774 774  
775 -
776 776  A GPS packet with lower PDOP has higher accuracy. PDOP default value is 2.0
777 777  
778 778  
779 -* (% style="color:blue" %)**AT Command:**
643 +* AT Command:
780 780  
781 -(% style="color:#037691" %)**AT+PDOP=2.5 ** (%%) **~-~->  ** Set PDOP to 2.5
645 +AT+PDOP=2.5  à Set PDOP to 2.5
782 782  
783 783  
784 -* (% style="color:blue" %)**Downlink Payload (prefix 0xAD):**
648 +* Downlink Payload (prefix 0xAD):
785 785  
786 -(% style="color:#037691" %)**0xAD 00 0A**   (%%) ~/~/  Set AT+PDOP=1  (0x0A / 10 =1)
650 +0xAD 00 0A    ~/~/Set AT+PDOP=1    (0x0A / 10 =1)
787 787  
788 -(% style="color:#037691" %)**0xAD 00 19**   (%%) ~/~/  Set AT+PDOP=2.5    (0x19 / 10 =2.5)
652 +0xAD 00 19    ~/~/Set AT+PDOP=2.5    (0x19 / 10 =2.5)
789 789  
790 -(% style="color:#037691" %)**0xAD 00 46**    (%%) ~/~/  Set AT+PDOP=7  (0x46 / 10 =7)
654 +0xAD 00 46    ~/~/Set AT+PDOP=7     (0x46 / 10 =7)
791 791  
656 +Disable/Enable the confirmation mode
792 792  
658 +* AT Command:
793 793  
794 -Disable/Enable the confirmation mode
660 +AT+CFM=xx.
795 795  
796 -* (% style="color:blue" %)**AT Command:**
662 + Example:
797 797  
798 -(% style="color:#037691" %)**AT+CFM=xx. **
664 + AT+ CFM=0    à Disable confirmation
799 799  
666 + AT+ CFM=1    à Enable confirmation
800 800  
801 -**~ Example:**
802 802  
803 - AT+ CFM=0    **~-~->   ** Disable confirmation
669 +* Downlink Payload (prefix 0x05):
804 804  
805 - AT+ CFM=1    **~-~->  ** Enable confirmation
671 +0x05 01      ~/~/ Same as AT+ SMOD =1
806 806  
807 807  
808 -* (% style="color:blue" %)**Downlink Payload (prefix 0x05):**
809 809  
810 -(% style="color:#037691" %)**0x05 01 **(%%) ~/~/  Same as AT+ SMOD =1
811 811  
812 812  
813 813  
... ... @@ -820,39 +820,35 @@
820 820  
821 821  == 5.1 Firmware Change Log ==
822 822  
823 -
824 824  **[[See this link>>url:https://github.com/dragino/TrackerD]]**
825 825  
826 826  
827 -
828 828  == 5.2 How to upgrade firmware ==
829 829  
692 +User can use the TrackerD ’s USB port to upgrade firmware into it. The hardware connection for upgrade firmware is as below:
830 830  
831 -User can use the TrackerD's USB port to upgrade firmware into it. The hardware connection for upgrade firmware is as below:
832 832  
695 +**(% style="color:blue" %)Step1:  **(%%)Connect TrackerD and PC via USB cable shipped with TrackerD.
833 833  
834 -(% style="color:blue" %)**Step1:  **(%%)Connect TrackerD and PC via USB cable shipped with TrackerD.
697 +**(% style="color:blue" %)Step2:** (%%) Install CH9102 driver in the PC.
835 835  
836 -
837 -(% style="color:blue" %)**Step2:** (%%) Install CH9102 driver in the PC.
838 -
839 839  After installation of the driver and plug in TrackerD, user should be able to see com port in PC's device manager.
840 840  
841 841  
842 -(% style="color:blue" %)**Step3:  **(%%)Download and Install Flash Tool:  [[https:~~/~~/www.espressif.com.cn/en/support/download/other-tools?keys=Flash%2BDownload%2BTools>>url:https://www.espressif.com.cn/en/support/download/other-tools?keys=Flash%2BDownload%2BTools]]
702 +**(% style="color:blue" %)Step3：**(%%) Download and Install Flash Tool:
843 843  
704 +[[https:~~/~~/www.espressif.com.cn/en/support/download/other-tools?keys=Flash%2BDownload%2BTools>>url:https://www.espressif.com.cn/en/support/download/other-tools?keys=Flash%2BDownload%2BTools]]
844 844  
845 -(% style="color:blue" %)**Step4:** (%%) Run Flash Download Tool and configure chip type to ESP32
706 +**(% style="color:blue" %)Step4:** (%%) Run Flash Download Tool and configure chip type to ESP32
846 846  
847 847  
848 -[[image:1664503563660-578.png]]
709 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image021.png||alt="image-20220712083115-1.png"]]
849 849  
711 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image022.png||alt="image-20220712083115-2.png"]]
850 850  
851 -[[image:1664503574618-659.png]]
852 852  
714 +**(% style="color:blue" %)Step5:** (%%) Select the firmware file (.bin format), com port and proper SPI configure. Clink Start. Bin file location:
853 853  
854 -(% style="color:blue" %)**Step5:** (%%) Select the firmware file (.bin format), com port and proper SPI configure. Clink Start. Bin file location:
855 -
856 856  [[https:~~/~~/www.dropbox.com/sh/733s8xlwahhqg1d/AABxDz80lBVX_to8zNuUQWFja?dl=0>>url:https://www.dropbox.com/sh/733s8xlwahhqg1d/AABxDz80lBVX_to8zNuUQWFja?dl=0]]
857 857  
858 858  
... ... @@ -862,17 +862,16 @@
862 862  
863 863  ESP_LORA-eeprom-class.bin @ 0x10000
864 864  
725 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image023.png||alt="image-20220712083115-3.png"]]
865 865  
866 -[[image:1664503593459-435.png]]
727 +After upgrade finish, it will show finish as below:
867 867  
729 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image024.png||alt="image-20220712083115-4.png"]]
868 868  
869 869  
870 -After upgrade finish, it will show finish as below:
871 871  
872 -[[image:1664503611848-385.png]]
873 873  
874 874  
875 -
876 876  = 6. Developer Guide =
877 877  
878 878  
... ... @@ -882,26 +882,28 @@
882 882  === 6.1.1 Set up ARDUINO compile environment ===
883 883  
884 884  
885 -* **Download the latest Arduino software (IDE) from the Arduino official website:  [[https:~~/~~/www.arduino.cc/en/Main/Software>>url:https://www.arduino.cc/en/Main/Software]]**
744 +* Download the latest Arduino software (IDE) from the Arduino official website
886 886  
887 -Install IDE on PC, open and click (% style="color:#037691" %)**File ~-~-> Preference**,(%%) add the following URL:  [[https:~~/~~/dl.espressif.com/dl/package_esp32_index.json>>url:https://links.jianshu.com/go?to=https%3A%2F%2Fdl.espressif.com%2Fdl%2Fpackage_esp32_index.json]]
746 +[[https:~~/~~/www.arduino.cc/en/Main/Software>>url:https://www.arduino.cc/en/Main/Software]]
888 888  
748 +Install IDE on PC, open and click File ~-~-> Preference, add the following URL [[https:~~/~~/dl.espressif.com/dl/package_esp32_index.json>>url:https://links.jianshu.com/go?to=https%3A%2F%2Fdl.espressif.com%2Fdl%2Fpackage_esp32_index.json]]
889 889  
890 -[[image:1664503635019-941.png]]
750 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image025.png]]
891 891  
752 +* Go to tools ~-~-> Boards ~-~-> Boards Manager, find the esp32 information and install it.
892 892  
893 -* (% style="color:#037691" %)**Go to tools ~-~-> Boards ~-~-> Boards Manager**,(%%) **find the esp32 information and install it.**
754 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image026.png]]
894 894  
895 -[[image:1664503715811-892.png]]
896 896  
757 +* Download the latest TrackerD from the dragino github
897 897  
759 +[[https:~~/~~/github.com/dragino/TrackerD>>url:https://github.com/dragino/TrackerD]]
898 898  
899 -* **Download the latest TrackerD from the dragino github: [[https:~~/~~/github.com/dragino/TrackerD>>url:https://github.com/dragino/TrackerD]]**
900 900  
901 -Put the Library in the TrackerD directory into the libraries file in the Arduino directory:
762 +Put the Library in the TrackerD directory into the libraries file in the Arduino directory
902 902  
764 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image027.png]]
903 903  
904 -[[image:1664503752288-974.png]]
905 905  
906 906  
907 907  
... ... @@ -908,21 +908,21 @@
908 908  == 6.2 Source Code ==
909 909  
910 910  
911 -* (% style="color:blue" %)**Open the example in the TrackerD file, please select the correct port in the IDE, as shown below:**
772 +* Open the example in the TrackerD file, please select the correct port in the IDE, as shown below:
912 912  
913 -[[image:1664503794261-827.png]]
774 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image028.png]]
914 914  
776 +* Click to upload
915 915  
778 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image029.png]]
916 916  
917 -* (% style="color:blue" %)**Click to upload**
780 +* Check the result, if the upload is successful, as shown below, open the serial port to view the data
918 918  
919 -[[image:1664503808294-336.png]]
920 920  
783 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image030.png]] [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image031.png]]
921 921  
922 922  
923 -* (% style="color:blue" %)**Check the result, if the upload is successful, as shown below, open the serial port to view the data**
924 924  
925 -[[image:1664503824081-592.png]] [[image:1664503831430-500.png]]
926 926  
927 927  
928 928  
... ... @@ -929,10 +929,11 @@
929 929  = 7.  FAQ =
930 930  
931 931  
793 +
932 932  == 7.1 How to change the LoRa Frequency Bands/Region? ==
933 933  
934 934  
935 -User can follow the introduction for [[how to upgrade image>>||anchor="H5.UploadFirmware"]]. When download the images, choose the required image file for download.
797 +User can follow the introduction for [[how to upgrade image>>path:#upgrade_image]]. When download the images, choose the required image file for download.
936 936  
937 937  
938 938  
... ... @@ -943,8 +943,8 @@
943 943  
944 944  
945 945  
946 -(% border="1.5" cellspacing="3" style="background-color:#ffffcc; color:green; width:314px" %)
947 -|=(% style="width: 118px;" %)**Pin**|=(% style="width: 67px;" %)**Color**|=(% style="width: 123px;" %)**USB Pin**
808 +(% border="2" style="background-color:#ffffcc; color:green; width:314px" %)
809 +|(% style="width:118px" %)**Pin**|(% style="width:67px" %)**Color**|(% style="width:123px" %)**USB Pin**
948 948  |(% style="width:118px" %)A4,B4,A9,B9|(% style="width:67px" %)Red|(% style="width:123px" %)VCC
949 949  |(% style="width:118px" %)A7,B7|(% style="width:67px" %)White|(% style="width:123px" %)D- (N/A)
950 950  |(% style="width:118px" %)A6,B6|(% style="width:67px" %)Green|(% style="width:123px" %)D+(N/A)
... ... @@ -962,6 +962,7 @@
962 962  (% style="color:blue" %)**XXX**(%%): The default frequency band
963 963  
964 964  * (% style="color:red" %)**EU433**(%%): Default frequency band EU433
827 +* (% style="color:red" %)**CN470**(%%): Default frequency band CN470
965 965  * (% style="color:red" %)**EU868**(%%): Default frequency band EU868
966 966  * (% style="color:red" %)**IN865**(%%): Default frequency band IN865
967 967  * (% style="color:red" %)**KR920**(%%): Default frequency band KR920
... ... @@ -969,25 +969,33 @@
969 969  * (% style="color:red" %)**AU915**(%%): Default frequency band AU915
970 970  * (% style="color:red" %)**US915**(%%): Default frequency band US915
971 971  
835 +
972 972  = 9.  Packing Info =
973 973  
974 974  
975 -(% style="color:#037691" %)**Package Includes**:
839 +**Package Includes**:
976 976  
977 -* TrackerD LoRaWAN GPS/BLE Tracker x 1
978 -* USB recharge & program cable x 1
841 +* TrackerD x 1
842 +* Rechargeable cable x 1
843 +* Program Cable x 1
979 979  
980 -(% style="color:#037691" %)**Dimensions and Weight**:
845 +**Dimensions and Weight**:
981 981  
982 -* Device Size: 85 x 48 x 15 cm
983 -* Weight: 50g
847 +* Device Size: 85 x 48 x 15 mm/pcs
848 +* Weight: 55g/pcs
984 984  
985 -= 10. Support =
986 986  
987 987  
852 += 10. Support =
853 +
988 988  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
989 -* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]].
855 +* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to
990 990  
857 +[[support@dragino.com>>url:file:///D:/市场资料/说明书/LoRa/LT系列/support@dragino.com]]
858 +
859 +
860 +
861 +
991 991  = 11.  Reference =
992 992  
993 993  
... ... @@ -994,5 +994,3 @@
994 994  * [[**Firmware in Bin format**>>https://www.dropbox.com/sh/733s8xlwahhqg1d/AABxDz80lBVX_to8zNuUQWFja?dl=0]]
995 995  * **[[Source Code>>https://github.com/dragino/TrackerD]] **
996 996  * [[**Hardware Source**>>https://www.dropbox.com/sh/orwoy6cecb89m4e/AAD37sRuUrvKsHgAJxuVTkB5a?dl=0]]
997 -
998 -
1664503635019-941.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -161.8 KB
Content
1664503715811-892.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -36.6 KB
Content
1664503752288-974.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -112.6 KB
Content
1664503794261-827.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -119.5 KB
Content
1664503808294-336.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -161.6 KB
Content
1664503824081-592.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -77.4 KB
Content
1664503831430-500.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -147.8 KB
Content
1664505654417-133.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -27.5 KB
Content
1665301570342-765.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -31.6 KB
Content
1665301636888-168.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -36.6 KB
Content
1665301687277-443.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -22.6 KB
Content
1665301786397-168.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -22.6 KB
Content
image-20221006181316-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Edwin
Size
... ... @@ -1,1 +1,0 @@
1 -17.7 KB
Content
image-20221006181357-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Edwin
Size
... ... @@ -1,1 +1,0 @@
1 -88.0 KB
Content