Skip to Content
Last modified by Xiaoling on 2025/04/27 16:48
From version 153.1
edited by Edwin Chen
on 2022/11/24 09:16
Change comment: There is no comment for this version
To version 155.2
edited by Xiaoling
on 2022/11/24 17:00
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Edwin
1 +XWiki.Xiaoling
Content
... ... @@ -421,7 +421,7 @@
421 421  === 2.4.4  Uplink FPORT~=4, History GNSS Positioning ===
422 422  
423 423  
424 -Set [[PNACKMD=1>>||anchor="H3.2.10A0A0AutoSendNone-ACKmessages"]], and TrackerD will wait for ACK for every uplink, when there is no LoRaWAN network, TrackerD will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
424 +Set [[PNACKMD=1>>||anchor="H3.2.11A0A0AutoSendNone-ACKmessages"]], and TrackerD will wait for ACK for every uplink, when there is no LoRaWAN network, TrackerD will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
425 425  
426 426  
427 427  (% style="color:red" %)**Note for this mode:**
... ... @@ -546,7 +546,7 @@
546 546  
547 547  total 273 entries,by default,
548 548  
549 -User can set [[PNACKMD=1>>||anchor="H3.2.10A0A0AutoSendNone-ACKmessages"]], to enable Datalog feature.
549 +User can set [[PNACKMD=1>>||anchor="H3.2.11A0A0AutoSendNone-ACKmessages"]], to enable Datalog feature.
550 550  
551 551  Example use case.
552 552  
... ... @@ -590,7 +590,6 @@
590 590  * **[[TDC>>||anchor="H3.2.1SetTransmitInterval"]]** defines the uplink interval when TrackerD is stactic.
591 591  * **[[PT>>||anchor="H3.2.16GetorSetThresholdformotiondetectFF08Sincefirmware1.4.3FF09"]]** defines the threldhold to detect a motion.
592 592  
593 -
594 594  == 2.10 LED Status ==
595 595  
596 596  
... ... @@ -1231,15 +1231,19 @@
1231 1231  
1232 1232  == 8.3  Problem after Upgrading Firmware ==
1233 1233  
1234 -=== 8.3.1 Continue Restart after upgrading ===
1233 +=== 8.3.1 "rst: (0x3 SW_RESET)" and Continue Restart after upgrading ===
1235 1235  
1235 +Error Output
1236 1236  
1237 +[[image:image-20221122100004-4.png||_mstalt="424606"]]
1238 +
1237 1237  (((
1238 -If it is V1.4.0 and the previous version, new partitions need to be loaded when upgrading. The new version of the software is stored in the partition package. The upgrade method is shown in the figure
1240 +Some partition is missed during upgrade, please upgrade below four files as example:
1241 +
1242 +[[image:image-20221122100004-2.png||_mstalt="423878" height="619" width="389"]]
1239 1239  )))
1240 1240  
1241 1241  
1242 -[[image:image-20221118105249-3.png||_mstalt="430664"]]
1243 1243  
1244 1244  
1245 1245  === 8.3.2 TrackerD's led light is always GREEN on after upgrading ===
... ... @@ -1297,12 +1297,6 @@
1297 1297  
1298 1298  
1299 1299  
1300 -=== 8.3.4  If there is a situation in Figure 1, and a new partition file needs to be added. Please refer to the operation steps in chapter 8.3.1 ===
1301 -
1302 -
1303 -[[image:image-20221122100004-4.png||_mstalt="424606"]]
1304 -
1305 -
1306 1306  == 8.4  When positioning, it will restart or the PDOP setting is unsuccessful ==
1307 1307  
1308 1308