Skip to Content
Last modified by Xiaoling on 2023/12/27 09:15
From version 155.2
edited by Xiaoling
on 2022/11/24 17:00
Change comment: There is no comment for this version
To version 151.1
edited by Edwin Chen
on 2022/11/24 09:08
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Xiaoling
1 +XWiki.Edwin
Content
... ... @@ -421,7 +421,7 @@
421 421  === 2.4.4  Uplink FPORT~=4, History GNSS Positioning ===
422 422  
423 423  
424 -Set [[PNACKMD=1>>||anchor="H3.2.11A0A0AutoSendNone-ACKmessages"]], and TrackerD will wait for ACK for every uplink, when there is no LoRaWAN network, TrackerD will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
424 +Set [[PNACKMD=1>>||anchor="H3.2.10A0A0AutoSendNone-ACKmessages"]], and TrackerD will wait for ACK for every uplink, when there is no LoRaWAN network, TrackerD will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
425 425  
426 426  
427 427  (% style="color:red" %)**Note for this mode:**
... ... @@ -546,7 +546,7 @@
546 546  
547 547  total 273 entries,by default,
548 548  
549 -User can set [[PNACKMD=1>>||anchor="H3.2.11A0A0AutoSendNone-ACKmessages"]], to enable Datalog feature.
549 +User can set [[PNACKMD=1>>||anchor="H3.2.10A0A0AutoSendNone-ACKmessages"]], to enable Datalog feature.
550 550  
551 551  Example use case.
552 552  
... ... @@ -588,8 +588,9 @@
588 588  
589 589  * **[[MTDC>>||anchor="H3.2.3SetTransportModePackettransmissioninterval"]]** defines the Uplink Interval during transportation.
590 590  * **[[TDC>>||anchor="H3.2.1SetTransmitInterval"]]** defines the uplink interval when TrackerD is stactic.
591 -* **[[PT>>||anchor="H3.2.16GetorSetThresholdformotiondetectFF08Sincefirmware1.4.3FF09"]]** defines the threldhold to detect a motion.
591 +* **[[PT>>||anchor="H3.2.1SetTransmitInterval"]]** defines the threldhold to detect a motion.
592 592  
593 +
593 593  == 2.10 LED Status ==
594 594  
595 595  
... ... @@ -960,26 +960,6 @@
960 960  Example: 0x24 01 ~/~/ Same as AT+CHE=1
961 961  
962 962  
963 -=== 3.2.16 Get or Set Threshold for motion detect（Since firmware 1.4.3） ===
964 -
965 -User can set the motion detect thredhold for transportation mode. The smaller the value, the more sensitivity to trigger a motion event.
966 -
967 -(% style="color:blue" %)**AT Command:**
968 -
969 -(% style="color:#037691" %)**AT+PT=xx**
970 -
971 - Example:
972 -
973 - AT+PT=14    ~-~->    Set to detect car motion.
974 -
975 - AT+PT=41   ~-~->    set to detect walk motion.
976 -
977 -
978 -(% style="color:blue" %)**Downlink Payload:0xB4**(%%)
979 -0xB4 14          ~/~/  Same as AT+PT=14
980 -
981 -
982 -
983 983  = 4. Setting for Different Scenarios =
984 984  
985 985  
... ... @@ -1230,19 +1230,15 @@
1230 1230  
1231 1231  == 8.3  Problem after Upgrading Firmware ==
1232 1232  
1233 -=== 8.3.1 "rst: (0x3 SW_RESET)" and Continue Restart after upgrading ===
1214 +=== 8.3.1 Continue Restart after upgrading ===
1234 1234  
1235 -Error Output
1236 1236  
1237 -[[image:image-20221122100004-4.png||_mstalt="424606"]]
1238 -
1239 1239  (((
1240 -Some partition is missed during upgrade, please upgrade below four files as example:
1241 -
1242 -[[image:image-20221122100004-2.png||_mstalt="423878" height="619" width="389"]]
1218 +If it is V1.4.0 and the previous version, new partitions need to be loaded when upgrading. The new version of the software is stored in the partition package. The upgrade method is shown in the figure
1243 1243  )))
1244 1244  
1245 1245  
1222 +[[image:image-20221118105249-3.png||_mstalt="430664"]]
1246 1246  
1247 1247  
1248 1248  === 8.3.2 TrackerD's led light is always GREEN on after upgrading ===
... ... @@ -1300,6 +1300,12 @@
1300 1300  
1301 1301  
1302 1302  
1280 +=== 8.3.4  If there is a situation in Figure 1, and a new partition file needs to be added. Please refer to the operation steps in chapter 8.3.1 ===
1281 +
1282 +
1283 +[[image:image-20221122100004-4.png||_mstalt="424606"]]
1284 +
1285 +
1303 1303  == 8.4  When positioning, it will restart or the PDOP setting is unsuccessful ==
1304 1304  
1305 1305