Skip to Content
Last modified by Xiaoling on 2023/12/27 09:15
From version 148.1
edited by Bei Jinggeng
on 2022/11/24 09:06
Change comment: There is no comment for this version
To version 155.2
edited by Xiaoling
on 2022/11/24 17:00
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Bei
1 +XWiki.Xiaoling
Content
... ... @@ -421,7 +421,7 @@
421 421  === 2.4.4  Uplink FPORT~=4, History GNSS Positioning ===
422 422  
423 423  
424 -Set [[PNACKMD=1>>||anchor="H3.2.10A0A0AutoSendNone-ACKmessages"]], and TrackerD will wait for ACK for every uplink, when there is no LoRaWAN network, TrackerD will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
424 +Set [[PNACKMD=1>>||anchor="H3.2.11A0A0AutoSendNone-ACKmessages"]], and TrackerD will wait for ACK for every uplink, when there is no LoRaWAN network, TrackerD will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
425 425  
426 426  
427 427  (% style="color:red" %)**Note for this mode:**
... ... @@ -546,7 +546,7 @@
546 546  
547 547  total 273 entries,by default,
548 548  
549 -User can set [[PNACKMD=1>>||anchor="H3.2.10A0A0AutoSendNone-ACKmessages"]], to enable Datalog feature.
549 +User can set [[PNACKMD=1>>||anchor="H3.2.11A0A0AutoSendNone-ACKmessages"]], to enable Datalog feature.
550 550  
551 551  Example use case.
552 552  
... ... @@ -586,6 +586,9 @@
586 586  
587 587  In Transport Mode, TrackerD will check if there is motion. If there is no motion, device will send uplinks every 20 minutes. If there is motion, device will send uplink every 5 minutes.
588 588  
589 +* **[[MTDC>>||anchor="H3.2.3SetTransportModePackettransmissioninterval"]]** defines the Uplink Interval during transportation.
590 +* **[[TDC>>||anchor="H3.2.1SetTransmitInterval"]]** defines the uplink interval when TrackerD is stactic.
591 +* **[[PT>>||anchor="H3.2.16GetorSetThresholdformotiondetectFF08Sincefirmware1.4.3FF09"]]** defines the threldhold to detect a motion.
589 589  
590 590  == 2.10 LED Status ==
591 591  
... ... @@ -957,6 +957,26 @@
957 957  Example: 0x24 01 ~/~/ Same as AT+CHE=1
958 958  
959 959  
963 +=== 3.2.16 Get or Set Threshold for motion detect（Since firmware 1.4.3） ===
964 +
965 +User can set the motion detect thredhold for transportation mode. The smaller the value, the more sensitivity to trigger a motion event.
966 +
967 +(% style="color:blue" %)**AT Command:**
968 +
969 +(% style="color:#037691" %)**AT+PT=xx**
970 +
971 + Example:
972 +
973 + AT+PT=14    ~-~->    Set to detect car motion.
974 +
975 + AT+PT=41   ~-~->    set to detect walk motion.
976 +
977 +
978 +(% style="color:blue" %)**Downlink Payload:0xB4**(%%)
979 +0xB4 14          ~/~/  Same as AT+PT=14
980 +
981 +
982 +
960 960  = 4. Setting for Different Scenarios =
961 961  
962 962  
... ... @@ -1207,15 +1207,19 @@
1207 1207  
1208 1208  == 8.3  Problem after Upgrading Firmware ==
1209 1209  
1210 -=== 8.3.1 Continue Restart after upgrading ===
1233 +=== 8.3.1 "rst: (0x3 SW_RESET)" and Continue Restart after upgrading ===
1211 1211  
1235 +Error Output
1212 1212  
1237 +[[image:image-20221122100004-4.png||_mstalt="424606"]]
1238 +
1213 1213  (((
1214 -If it is V1.4.0 and the previous version, new partitions need to be loaded when upgrading. The new version of the software is stored in the partition package. The upgrade method is shown in the figure
1240 +Some partition is missed during upgrade, please upgrade below four files as example:
1241 +
1242 +[[image:image-20221122100004-2.png||_mstalt="423878" height="619" width="389"]]
1215 1215  )))
1216 1216  
1217 1217  
1218 -[[image:image-20221118105249-3.png||_mstalt="430664"]]
1219 1219  
1220 1220  
1221 1221  === 8.3.2 TrackerD's led light is always GREEN on after upgrading ===
... ... @@ -1273,12 +1273,6 @@
1273 1273  
1274 1274  
1275 1275  
1276 -=== 8.3.4  If there is a situation in Figure 1, and a new partition file needs to be added. Please refer to the operation steps in chapter 8.3.1 ===
1277 -
1278 -
1279 -[[image:image-20221122100004-4.png||_mstalt="424606"]]
1280 -
1281 -
1282 1282  == 8.4  When positioning, it will restart or the PDOP setting is unsuccessful ==
1283 1283  
1284 1284