Wiki source code of SN50v3-LB/LS -- LoRaWAN Sensor Node User Manual

Version 97.1 by Saxer Lin on 2024/07/25 18:52

version	line-number	content
87.2	1
	2
41.2	3	(% style="text-align:center" %)
87.2	4	[[image:image-20240103095714-2.png]]
2.1	5
	6
	7
87.2	8
	9
	10
79.3	11	Table of Contents:
2.1	12
	13	{{toc/}}
	14
	15
	16
	17
	18
	19
	20	= 1. Introduction =
	21
87.3	22	== 1.1 What is SN50v3-LB/LS LoRaWAN Generic Node ==
2.1	23
43.2	24
87.4	25	(% style="color:blue" %)SN50V3-LB/LS (%%)LoRaWAN Sensor Node is a Long Range LoRa Sensor Node. It is designed for outdoor use and powered by (% style="color:blue" %) 8500mAh Li/SOCl2 battery(%%) or (% style="color:blue" %)solar powered + li-on battery(%%) for long term use.SN50V3-LB/LS is designed to facilitate developers to quickly deploy industrial level LoRa and IoT solutions. It help users to turn the idea into a practical application and make the Internet of Things a reality. It is easy to program, create and connect your things everywhere.
2.1	26
87.3	27	(% style="color:blue" %)SN50V3-LB/LS wireless part(%%) is based on SX1262 allows the user to send data and reach extremely long ranges at low data-rates.It provides ultra-long range spread spectrum communication and high interference immunity whilst minimising current consumption.It targets professional wireless sensor network applications such as irrigation systems, smart metering, smart cities, and so on.
2.1	28
87.3	29	SN50V3-LB/LS has a powerful (% style="color:blue" %)48Mhz ARM microcontroller with 256KB flash and 64KB RAM(%%). It has (% style="color:blue" %)multiplex I/O pins(%%) to connect to different sensors.
2.1	30
87.3	31	SN50V3-LB/LS has a (% style="color:blue" %)built-in BLE module(%%), user can configure the sensor remotely via Mobile Phone. It also support (% style="color:blue" %)OTA upgrade(%%) via private LoRa protocol for easy maintaining.
2.1	32
87.3	33	SN50V3-LB/LS is the 3^^rd^^ generation of LSN50 series generic sensor node from Dragino. It is an (% style="color:blue" %)open source project(%%) and has a mature LoRaWAN stack and application software. User can use the pre-load software for their IoT projects or easily customize the software for different requirements.
2.1	34
	35	== 1.2 Features ==
	36
43.44	37
2.1	38	* LoRaWAN 1.0.3 Class A
	39	* Ultra-low power consumption
5.1	40	* Open-Source hardware/software
2.1	41	* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
	42	* Support Bluetooth v5.1 and LoRaWAN remote configure
	43	* Support wireless OTA update firmware
	44	* Uplink on periodically
	45	* Downlink to change configure
87.26	46	* 8500mAh Li/SOCl2 Battery (SN50v3-LB)
87.5	47	* Solar panel + 3000mAh Li-on battery (SN50v3-LS)
2.1	48
	49	== 1.3 Specification ==
	50
43.4	51
2.1	52	(% style="color:#037691" %)Common DC Characteristics:
	53
87.28	54	* Supply Voltage: Built-in Battery , 2.5v ~~ 3.6v
2.1	55	* Operating Temperature: -40 ~~ 85°C
	56
5.1	57	(% style="color:#037691" %)I/O Interface:
2.1	58
5.1	59	* Battery output (2.6v ~~ 3.6v depends on battery)
	60	* +5v controllable output
	61	* 3 x Interrupt or Digital IN/OUT pins
	62	* 3 x one-wire interfaces
	63	* 1 x UART Interface
	64	* 1 x I2C Interface
2.1	65
	66	(% style="color:#037691" %)LoRa Spec:
	67
	68	* Frequency Range, Band 1 (HF): 862 ~~ 1020 Mhz
	69	* Max +22 dBm constant RF output vs.
	70	* RX sensitivity: down to -139 dBm.
	71	* Excellent blocking immunity
	72
	73	(% style="color:#037691" %)Battery:
	74
	75	* Li/SOCI2 un-chargeable battery
	76	* Capacity: 8500mAh
	77	* Self-Discharge: <1% / Year @ 25°C
	78	* Max continuously current: 130mA
	79	* Max boost current: 2A, 1 second
	80
	81	(% style="color:#037691" %)Power Consumption
	82
	83	* Sleep Mode: 5uA @ 3.3v
	84	* LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm
	85
	86	== 1.4 Sleep mode and working mode ==
	87
43.4	88
2.1	89	(% style="color:blue" %)Deep Sleep Mode: (%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.
	90
	91	(% style="color:blue" %)Working Mode: (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.
	92
	93
	94	== 1.5 Button & LEDs ==
	95
	96
87.29	97	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/RS485-LB_Waterproof_RS485UART_to_LoRaWAN_Converter/WebHome/image-20240103160425-4.png?rev=1.1\|\|alt="image-20240103160425-4.png"]]
2.1	98
87.41	99	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
87.31	100	\|=(% style="width: 167px;background-color:#4F81BD;color:white" %)Behavior on ACT\|=(% style="width: 117px;background-color:#4F81BD;color:white" %)Function\|=(% style="width: 226px;background-color:#4F81BD;color:white" %)Action
2.1	101	\|(% style="width:167px" %)Pressing ACT between 1s < time < 3s\|(% style="width:117px" %)Send an uplink\|(% style="width:225px" %)(((
	102	If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, (% style="color:blue" %)blue led (%%)will blink once.
	103	Meanwhile, BLE module will be active and user can connect via BLE to configure device.
	104	)))
	105	\|(% style="width:167px" %)Pressing ACT for more than 3s\|(% style="width:117px" %)Active Device\|(% style="width:225px" %)(((
	106	(% style="color:green" %)Green led(%%) will fast blink 5 times, device will enter (% style="color:#037691" %)OTA mode(%%) for 3 seconds. And then start to JOIN LoRaWAN network.
	107	(% style="color:green" %)Green led(%%) will solidly turn on for 5 seconds after joined in network.
	108	Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device join or not join LoRaWAN network.
	109	)))
	110	\|(% style="width:167px" %)Fast press ACT 5 times.\|(% style="width:117px" %)Deactivate Device\|(% style="width:225px" %)(% style="color:red" %)Red led(%%) will solid on for 5 seconds. Means device is in Deep Sleep Mode.
	111
	112	== 1.6 BLE connection ==
	113
	114
87.4	115	SN50v3-LB/LS supports BLE remote configure.
2.1	116
	117
	118	BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:
	119
	120	* Press button to send an uplink
	121	* Press button to active device.
	122	* Device Power on or reset.
	123
	124	If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.
	125
	126
6.1	127	== 1.7 Pin Definitions ==
2.1	128
	129
49.1	130	[[image:image-20230610163213-1.png\|\|height="404" width="699"]]
2.1	131
	132
	133	== 1.8 Mechanical ==
	134
85.1	135	=== 1.8.1 for LB version ===
2.1	136
	137
84.1	138	[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143884058-338.png]][[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143899218-599.png]]
2.1	139
84.1	140
2.1	141	[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143909447-639.png]]
	142
85.1	143	=== 1.8.2 for LS version ===
2.1	144
84.1	145	[[image:image-20231231203439-3.png\|\|height="385" width="886"]]
	146
	147
44.5	148	== 1.9 Hole Option ==
5.1	149
43.4	150
87.4	151	SN50v3-LB/LS has different hole size options for different size sensor cable. The options provided are M12, M16 and M20. The definition is as below:
5.1	152
	153	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220627104757-1.png?rev=1.1\|\|alt="image-20220627104757-1.png"]]
	154
	155	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656298089706-973.png?rev=1.1\|\|alt="1656298089706-973.png"]]
	156
	157
87.4	158	= 2. Configure SN50v3-LB/LS to connect to LoRaWAN network =
2.1	159
	160	== 2.1 How it works ==
	161
	162
87.4	163	The SN50v3-LB/LS is configured as (% style="color:#037691" %)LoRaWAN OTAA Class A(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the SN50v3-LB/LS. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
2.1	164
	165
	166	== 2.2 Quick guide to connect to LoRaWAN server (OTAA) ==
	167
	168
	169	Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.
	170
44.3	171	The LPS8v2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
2.1	172
	173
87.4	174	(% style="color:blue" %)Step 1:(%%) Create a device in TTN with the OTAA keys from SN50v3-LB/LS.
2.1	175
87.4	176	Each SN50v3-LB/LS is shipped with a sticker with the default device EUI as below:
2.1	177
11.2	178	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/S31-LB_S31B-LB/WebHome/image-20230426084152-1.png?width=502&height=233&rev=1.1\|\|alt="图片-20230426084152-1.png" height="233" width="502"]]
2.1	179
	180
	181	You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
	182
	183
	184	(% style="color:blue" %)Register the device
	185
	186	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/1654935135620-998.png?rev=1.1\|\|alt="1654935135620-998.png"]]
	187
	188
	189	(% style="color:blue" %)Add APP EUI and DEV EUI
	190
	191	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-4.png?width=753&height=551&rev=1.1\|\|alt="图片-20220611161308-4.png"]]
	192
	193
	194	(% style="color:blue" %)Add APP EUI in the application
	195
	196
	197	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-5.png?width=742&height=601&rev=1.1\|\|alt="图片-20220611161308-5.png"]]
	198
	199
	200	(% style="color:blue" %)Add APP KEY
	201
	202	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-6.png?width=744&height=485&rev=1.1\|\|alt="图片-20220611161308-6.png"]]
	203
87.4	204	(% style="color:blue" %)Step 2:(%%) Activate SN50v3-LB/LS
2.1	205
87.4	206	Press the button for 5 seconds to activate the SN50v3-LB/LS.
2.1	207
	208	(% style="color:green" %)Green led(%%) will fast blink 5 times, device will enter (% style="color:blue" %)OTA mode(%%) for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)Green led(%%) will solidly turn on for 5 seconds after joined in network.
	209
	210	After join success, it will start to upload messages to TTN and you can see the messages in the panel.
	211
	212
	213	== 2.3 Uplink Payload ==
	214
	215	=== 2.3.1 Device Status, FPORT~=5 ===
	216
	217
87.4	218	Users can use the downlink command(0x26 01) to ask SN50v3-LB/LS to send device configure detail, include device configure status. SN50v3-LB/LS will uplink a payload via FPort=5 to server.
2.1	219
	220	The Payload format is as below.
	221
	222
87.41	223	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
87.24	224	\|(% colspan="6" style="background-color:#4f81bd; color:white" %)Device Status (FPORT=5)
2.1	225	\|(% style="width:103px" %)Size (bytes)\|(% style="width:72px" %)1\|2\|(% style="width:91px" %)1\|(% style="width:86px" %)1\|(% style="width:44px" %)2
45.4	226	\|(% style="width:103px" %)Value\|(% style="width:72px" %)Sensor Model\|Firmware Version\|(% style="width:91px" %)Frequency Band\|(% style="width:86px" %)Sub-band\|(% style="width:44px" %)BAT
2.1	227
	228	Example parse in TTNv3
	229
	230
87.4	231	(% style="color:#037691" %)Sensor Model(%%): For SN50v3-LB/LS, this value is 0x1C
2.1	232
	233	(% style="color:#037691" %)Firmware Version(%%): 0x0100, Means: v1.0.0 version
	234
	235	(% style="color:#037691" %)Frequency Band:
	236
53.2	237	0x01: EU868
2.1	238
53.2	239	0x02: US915
2.1	240
53.2	241	0x03: IN865
2.1	242
53.2	243	0x04: AU915
2.1	244
53.2	245	0x05: KZ865
2.1	246
53.2	247	0x06: RU864
2.1	248
53.2	249	0x07: AS923
2.1	250
53.2	251	0x08: AS923-1
2.1	252
53.2	253	0x09: AS923-2
2.1	254
53.2	255	0x0a: AS923-3
2.1	256
53.2	257	0x0b: CN470
2.1	258
53.2	259	0x0c: EU433
2.1	260
53.2	261	0x0d: KR920
2.1	262
53.2	263	0x0e: MA869
2.1	264
	265
	266	(% style="color:#037691" %)Sub-Band:
	267
	268	AU915 and US915:value 0x00 ~~ 0x08
	269
	270	CN470: value 0x0B ~~ 0x0C
	271
	272	Other Bands: Always 0x00
	273
	274
	275	(% style="color:#037691" %)Battery Info:
	276
	277	Check the battery voltage.
	278
	279	Ex1: 0x0B45 = 2885mV
	280
	281	Ex2: 0x0B49 = 2889mV
	282
	283
12.1	284	=== 2.3.2 Working Modes & Sensor Data. Uplink via FPORT~=2 ===
2.1	285
	286
87.4	287	SN50v3-LB/LS has different working mode for the connections of different type of sensors. This section describes these modes. Use can use the AT Command (% style="color:blue" %)AT+MOD(%%) to set SN50v3-LB/LS to different working modes.
12.1	288
	289	For example:
	290
44.2	291	(% style="color:blue" %)AT+MOD=2 (%%) ~/~/ will set the SN50v3 to work in MOD=2 distance mode which target to measure distance via Ultrasonic Sensor.
12.1	292
	293
13.1	294	(% style="color:red" %) Important Notice:
12.1	295
87.4	296	~1. Some working modes has payload more than 12 bytes, The US915/AU915/AS923 frequency bands' definition has maximum 11 bytes in (% style="color:blue" %)DR0(%%). Server sides will see NULL payload while SN50v3-LB/LS transmit in DR0 with 12 bytes payload.
12.1	297
44.2	298	2. All modes share the same Payload Explanation from HERE.
43.53	299
44.2	300	3. By default, the device will send an uplink message every 20 minutes.
	301
	302
13.1	303	==== 2.3.2.1 MOD~=1 (Default Mode) ====
12.1	304
43.5	305
12.1	306	In this mode, uplink payload includes in total 11 bytes. Uplink packets use FPORT=2.
	307
87.32	308	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:517px" %)
	309	\|(% style="background-color:#4f81bd; color:white; width:50px" %)Size(bytes)\|(% style="background-color:#4f81bd; color:white; width:20px" %)2\|(% style="background-color:#4f81bd; color:white; width:100px" %)2\|(% style="background-color:#4f81bd; color:white; width:50px" %)2\|(% style="background-color:#4f81bd; color:white; width:90px" %)1\|(% style="background-color:#4f81bd; color:white; width:128px" %)2\|(% style="background-color:#4f81bd; color:white; width:79px" %)2
45.4	310	\|Value\|Bat\|(% style="width:191px" %)(((
43.12	311	Temperature(DS18B20)(PC13)
40.1	312	)))\|(% style="width:78px" %)(((
43.12	313	ADC(PA4)
26.2	314	)))\|(% style="width:216px" %)(((
43.13	315	Digital in(PB15)&Digital Interrupt(PA8)
40.1	316	)))\|(% style="width:308px" %)(((
43.12	317	Temperature(SHT20 or SHT31 or BH1750 Illumination Sensor)
40.1	318	)))\|(% style="width:154px" %)(((
43.12	319	Humidity(SHT20 or SHT31)
36.1	320	)))
	321
12.1	322	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220627150949-6.png?rev=1.1\|\|alt="image-20220627150949-6.png"]]
	323
	324
13.1	325	==== 2.3.2.2 MOD~=2 (Distance Mode) ====
	326
43.45	327
12.1	328	This mode is target to measure the distance. The payload of this mode is totally 11 bytes. The 8^^th^^ and 9^^th^^ bytes is for the distance.
	329
87.34	330	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:517px" %)
87.33	331	\|(% style="background-color:#4f81bd; color:white; width:50px" %)Size(bytes)\|(% style="background-color:#4f81bd; color:white; width:29px" %)2\|(% style="background-color:#4f81bd; color:white; width:108px" %)2\|(% style="background-color:#4f81bd; color:white; width:40px" %)2\|(% style="background-color:#4f81bd; color:white; width:110px" %)1\|(% style="background-color:#4f81bd; color:white; width:140px" %)2\|(% style="background-color:#4f81bd; color:white; width:40px" %)2
45.4	332	\|Value\|BAT\|(% style="width:196px" %)(((
43.16	333	Temperature(DS18B20)(PC13)
40.1	334	)))\|(% style="width:87px" %)(((
43.16	335	ADC(PA4)
40.1	336	)))\|(% style="width:189px" %)(((
43.16	337	Digital in(PB15) & Digital Interrupt(PA8)
40.1	338	)))\|(% style="width:208px" %)(((
53.2	339	Distance measure by: 1) LIDAR-Lite V3HP
	340	Or 2) Ultrasonic Sensor
40.1	341	)))\|(% style="width:117px" %)Reserved
12.1	342
	343	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656324539647-568.png?rev=1.1\|\|alt="1656324539647-568.png"]]
	344
43.45	345
43.17	346	(% style="color:blue" %)Connection of LIDAR-Lite V3HP:
12.1	347
26.2	348	[[image:image-20230512173758-5.png\|\|height="563" width="712"]]
12.1	349
43.45	350
43.17	351	(% style="color:blue" %)Connection to Ultrasonic Sensor:
12.1	352
44.1	353	(% style="color:red" %)Need to remove R1 and R2 resistors to get low power,otherwise there will be 240uA standby current.
36.1	354
26.2	355	[[image:image-20230512173903-6.png\|\|height="596" width="715"]]
12.1	356
43.45	357
12.1	358	For the connection to TF-Mini or TF-Luna , MOD2 payload is as below:
	359
87.34	360	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:517px" %)
	361	\|(% style="background-color:#4f81bd; color:white; width:50px" %)Size(bytes)\|(% style="background-color:#4f81bd; color:white; width:20px" %)2\|(% style="background-color:#4f81bd; color:white; width:100px" %)2\|(% style="background-color:#4f81bd; color:white; width:100px" %)1\|(% style="background-color:#4f81bd; color:white; width:50px" %)2\|(% style="background-color:#4f81bd; color:white; width:120px" %)2\|(% style="background-color:#4f81bd; color:white; width:77px" %)2
45.5	362	\|Value\|BAT\|(% style="width:183px" %)(((
43.19	363	Temperature(DS18B20)(PC13)
40.1	364	)))\|(% style="width:173px" %)(((
43.19	365	Digital in(PB15) & Digital Interrupt(PA8)
40.1	366	)))\|(% style="width:84px" %)(((
43.19	367	ADC(PA4)
40.1	368	)))\|(% style="width:323px" %)(((
12.1	369	Distance measure by:1)TF-Mini plus LiDAR
53.3	370	Or 2) TF-Luna LiDAR
40.1	371	)))\|(% style="width:188px" %)Distance signal strength
12.1	372
	373	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656376779088-686.png?rev=1.1\|\|alt="1656376779088-686.png"]]
	374
43.45	375
12.1	376	Connection to [[TF-Mini plus>>url:http://en.benewake.com/product/detail/5c345cd0e5b3a844c472329b.html]] LiDAR(UART version):
	377
44.1	378	(% style="color:red" %)Need to remove R3 and R4 resistors to get low power,otherwise there will be 400uA standby current.
12.1	379
26.2	380	[[image:image-20230512180609-7.png\|\|height="555" width="802"]]
12.1	381
43.45	382
12.1	383	Connection to [[TF-Luna>>url:http://en.benewake.com/product/detail/5e1c1fd04d839408076b6255.html]] LiDAR (UART version):
	384
44.1	385	(% style="color:red" %)Need to remove R3 and R4 resistors to get low power,otherwise there will be 400uA standby current.
12.1	386
52.1	387	[[image:image-20230610170047-1.png\|\|height="452" width="799"]]
12.1	388
	389
13.1	390	==== 2.3.2.3 MOD~=3 (3 ADC + I2C) ====
	391
43.45	392
12.1	393	This mode has total 12 bytes. Include 3 x ADC + 1x I2C
	394
87.35	395	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:517px" %)
87.11	396	\|=(% style="width: 50px;background-color:#4F81BD;color:white" %)(((
43.25	397	Size(bytes)
87.35	398	)))\|=(% style="width: 50px;background-color:#4F81BD;color:white" %)2\|=(% style="width: 50px;background-color:#4F81BD;color:white" %)2\|=(% style="width: 50px;background-color:#4F81BD;color:white" %)2\|=(% style="width: 90px;background-color:#4F81BD;color:white" %)1\|=(% style="width: 110px;background-color:#4F81BD;color:white" %)2\|=(% style="width: 97px;background-color:#4F81BD;color:white" %)2\|=(% style="width: 20px;background-color:#4F81BD;color:white" %)1
45.4	399	\|Value\|(% style="width:68px" %)(((
43.23	400	ADC1(PA4)
26.2	401	)))\|(% style="width:75px" %)(((
43.23	402	ADC2(PA5)
36.1	403	)))\|(((
43.23	404	ADC3(PA8)
36.1	405	)))\|(((
	406	Digital Interrupt(PB15)
	407	)))\|(% style="width:304px" %)(((
43.23	408	Temperature(SHT20 or SHT31 or BH1750 Illumination Sensor)
36.1	409	)))\|(% style="width:163px" %)(((
43.23	410	Humidity(SHT20 or SHT31)
36.1	411	)))\|(% style="width:53px" %)Bat
	412
	413	[[image:image-20230513110214-6.png]]
	414
	415
13.1	416	==== 2.3.2.4 MOD~=4 (3 x DS18B20) ====
	417
12.1	418
26.2	419	This mode has total 11 bytes. As shown below:
12.1	420
87.36	421	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:517px" %)
	422	\|(% style="background-color:#4f81bd; color:white; width:50px" %)Size(bytes)\|(% style="background-color:#4f81bd; color:white; width:20px" %)2\|(% style="background-color:#4f81bd; color:white; width:100px" %)2\|(% style="background-color:#4f81bd; color:white; width:50px" %)2\|(% style="background-color:#4f81bd; color:white; width:99px" %)1\|(% style="background-color:#4f81bd; color:white; width:99px" %)2\|(% style="background-color:#4f81bd; color:white; width:99px" %)2
45.4	423	\|Value\|BAT\|(% style="width:186px" %)(((
43.27	424	Temperature1(DS18B20)(PC13)
26.2	425	)))\|(% style="width:82px" %)(((
43.27	426	ADC(PA4)
26.2	427	)))\|(% style="width:210px" %)(((
43.27	428	Digital in(PB15) & Digital Interrupt(PA8)
26.2	429	)))\|(% style="width:191px" %)Temperature2(DS18B20)
43.27	430	(PB9)\|(% style="width:183px" %)Temperature3(DS18B20)(PB8)
12.1	431
	432	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656377606181-607.png?rev=1.1\|\|alt="1656377606181-607.png"]]
	433
44.4	434
39.2	435	[[image:image-20230513134006-1.png\|\|height="559" width="736"]]
12.1	436
39.1	437
13.1	438	==== 2.3.2.5 MOD~=5(Weight Measurement by HX711) ====
	439
43.45	440
26.2	441	[[image:image-20230512164658-2.png\|\|height="532" width="729"]]
12.1	442
	443	Each HX711 need to be calibrated before used. User need to do below two steps:
	444
44.2	445	1. Zero calibration. Don't put anything on load cell and run (% style="color:blue" %)AT+WEIGRE(%%) to calibrate to Zero gram.
	446	1. Adjust calibration factor (default value 400): Put a known weight thing on load cell and run (% style="color:blue" %)AT+WEIGAP(%%) to adjust the Calibration Factor.
12.1	447	1. (((
26.2	448	Weight has 4 bytes, the unit is g.
43.53	449
	450
	451
12.1	452	)))
	453
	454	For example:
	455
44.2	456	(% style="color:blue" %)AT+GETSENSORVALUE =0
12.1	457
	458	Response: Weight is 401 g
	459
	460	Check the response of this command and adjust the value to match the real value for thing.
	461
87.37	462	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:517px" %)
87.11	463	\|=(% style="width: 50px;background-color:#4F81BD;color:white" %)(((
12.1	464	Size(bytes)
87.37	465	)))\|=(% style="width: 20px;background-color:#4F81BD;color:white" %)2\|=(% style="width: 150px;background-color:#4F81BD;color:white" %)2\|=(% style="width: 50px;background-color:#4F81BD;color:white" %)2\|=(% style="width: 198px;background-color:#4F81BD;color:white" %)1\|=(% style="width: 49px;background-color:#4F81BD;color:white" %)4
45.4	466	\|Value\|BAT\|(% style="width:193px" %)(((
43.55	467	Temperature(DS18B20)(PC13)
40.1	468	)))\|(% style="width:85px" %)(((
43.31	469	ADC(PA4)
40.1	470	)))\|(% style="width:186px" %)(((
43.55	471	Digital in(PB15) & Digital Interrupt(PA8)
40.1	472	)))\|(% style="width:100px" %)Weight
26.2	473
12.1	474	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220820120036-2.png?width=1003&height=469&rev=1.1\|\|alt="image-20220820120036-2.png" height="469" width="1003"]]
	475
	476
13.1	477	==== 2.3.2.6 MOD~=6 (Counting Mode) ====
	478
43.45	479
12.1	480	In this mode, the device will work in counting mode. It counts the interrupt on the interrupt pins and sends the count on TDC time.
	481
	482	Connection is as below. The PIR sensor is a count sensor, it will generate interrupt when people come close or go away. User can replace the PIR sensor with other counting sensors.
	483
26.2	484	[[image:image-20230512181814-9.png\|\|height="543" width="697"]]
12.1	485
43.53	486
43.45	487	(% style="color:red" %)Note: LoRaWAN wireless transmission will infect the PIR sensor. Which cause the counting value increase +1 for every uplink. User can change PIR sensor or put sensor away of the SN50_v3 to avoid this happen.
12.1	488
87.38	489	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:517px" %)
	490	\|=(% style="width: 60px;background-color:#4F81BD;color:white" %)Size(bytes)\|=(% style="width: 40px;background-color:#4F81BD;color:white" %)2\|=(% style="width: 180px;background-color:#4F81BD;color:white" %)2\|=(% style="width: 60px;background-color:#4F81BD;color:white" %)2\|=(% style="width: 100px;background-color:#4F81BD;color:white" %)1\|=(% style="width: 77px;background-color:#4F81BD;color:white" %)4
45.4	491	\|Value\|BAT\|(% style="width:256px" %)(((
43.31	492	Temperature(DS18B20)(PC13)
36.1	493	)))\|(% style="width:108px" %)(((
43.31	494	ADC(PA4)
36.1	495	)))\|(% style="width:126px" %)(((
43.31	496	Digital in(PB15)
36.1	497	)))\|(% style="width:145px" %)(((
43.31	498	Count(PA8)
36.1	499	)))
	500
12.1	501	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656378441509-171.png?rev=1.1\|\|alt="1656378441509-171.png"]]
	502
	503
13.1	504	==== 2.3.2.7 MOD~=7 (Three interrupt contact modes) ====
	505
43.45	506
87.39	507	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:517px" %)
87.11	508	\|=(% style="width: 50px;background-color:#4F81BD;color:white" %)(((
12.1	509	Size(bytes)
87.39	510	)))\|=(% style="width: 20px;background-color:#4F81BD;color:white" %)2\|=(% style="width: 90px;background-color:#4F81BD;color:white" %)2\|=(% style="width: 50px;background-color:#4F81BD;color:white" %)2\|=(% style="width: 89px;background-color:#4F81BD;color:white" %)1\|=(% style="width: 89px;background-color:#4F81BD;color:white" %)1\|=(% style="width: 89px;background-color:#4F81BD;color:white" %)1\|=(% style="width: 40px;background-color:#4F81BD;color:white" %)2
45.4	511	\|Value\|BAT\|(% style="width:188px" %)(((
36.1	512	Temperature(DS18B20)
	513	(PC13)
40.1	514	)))\|(% style="width:83px" %)(((
43.35	515	ADC(PA5)
40.1	516	)))\|(% style="width:184px" %)(((
36.1	517	Digital Interrupt1(PA8)
40.1	518	)))\|(% style="width:186px" %)Digital Interrupt2(PA4)\|(% style="width:197px" %)Digital Interrupt3(PB15)\|(% style="width:100px" %)Reserved
36.1	519
	520	[[image:image-20230513111203-7.png\|\|height="324" width="975"]]
	521
43.45	522
13.1	523	==== 2.3.2.8 MOD~=8 （3ADC+1DS18B20） ====
	524
43.45	525
87.39	526	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:517px" %)
87.11	527	\|=(% style="width: 50px;background-color:#4F81BD;color:white" %)(((
12.1	528	Size(bytes)
87.39	529	)))\|=(% style="width: 30px;background-color:#4F81BD;color:white" %)2\|=(% style="width: 110px;background-color:#4F81BD;color:white" %)2\|=(% style="width: 70px;background-color:#4F81BD;color:white" %)2\|=(% style="width: 119px;background-color:#4F81BD;color:white" %)1\|=(% style="width: 69px;background-color:#4F81BD;color:white" %)2\|=(% style="width: 69px;background-color:#4F81BD;color:white" %)2
45.4	530	\|Value\|BAT\|(% style="width:207px" %)(((
36.1	531	Temperature(DS18B20)
	532	(PC13)
	533	)))\|(% style="width:94px" %)(((
43.36	534	ADC1(PA4)
36.1	535	)))\|(% style="width:198px" %)(((
	536	Digital Interrupt(PB15)
	537	)))\|(% style="width:84px" %)(((
43.36	538	ADC2(PA5)
40.1	539	)))\|(% style="width:82px" %)(((
43.36	540	ADC3(PA8)
12.1	541	)))
	542
36.1	543	[[image:image-20230513111231-8.png\|\|height="335" width="900"]]
12.1	544
	545
13.1	546	==== 2.3.2.9 MOD~=9 (3DS18B20+ two Interrupt count mode) ====
	547
43.45	548
87.40	549	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:517px" %)
87.11	550	\|=(% style="width: 50px;background-color:#4F81BD;color:white" %)(((
12.1	551	Size(bytes)
87.40	552	)))\|=(% style="width: 20px;background-color:#4F81BD;color:white" %)2\|=(% style="width: 90px;background-color:#4F81BD;color:white" %)2\|=(% style="width: 90px;background-color:#4F81BD;color:white" %)2\|=(% style="width: 60px;background-color:#4F81BD;color:white" %)1\|=(% style="width: 89px;background-color:#4F81BD;color:white" %)2\|=(% style="width: 59px;background-color:#4F81BD;color:white" %)4\|=(% style="width: 59px;background-color:#4F81BD;color:white" %)4
45.4	553	\|Value\|BAT\|(((
43.58	554	Temperature
	555	(DS18B20)(PC13)
12.1	556	)))\|(((
43.58	557	Temperature2
	558	(DS18B20)(PB9)
12.1	559	)))\|(((
36.1	560	Digital Interrupt
	561	(PB15)
	562	)))\|(% style="width:193px" %)(((
43.58	563	Temperature3
	564	(DS18B20)(PB8)
36.1	565	)))\|(% style="width:78px" %)(((
43.39	566	Count1(PA8)
36.1	567	)))\|(% style="width:78px" %)(((
43.39	568	Count2(PA4)
12.1	569	)))
	570
36.1	571	[[image:image-20230513111255-9.png\|\|height="341" width="899"]]
12.1	572
43.40	573	(% style="color:blue" %)The newly added AT command is issued correspondingly:
12.1	574
43.44	575	(% style="color:#037691" %) AT+INTMOD1 PA8(%%) pin： Corresponding downlink: (% style="color:#037691" %)06 00 00 xx
12.1	576
43.44	577	(% style="color:#037691" %) AT+INTMOD2 PA4(%%) pin： Corresponding downlink: (% style="color:#037691" %)06 00 01 xx
12.1	578
43.44	579	(% style="color:#037691" %) AT+INTMOD3 PB15(%%) pin： Corresponding downlink: (% style="color:#037691" %) 06 00 02 xx
12.1	580
	581
43.41	582	(% style="color:blue" %)AT+SETCNT=aa,bb
	583
36.1	584	When AA is 1, set the count of PA8 pin to BB Corresponding downlink：09 01 bb bb bb bb
12.1	585
36.1	586	When AA is 2, set the count of PA4 pin to BB Corresponding downlink：09 02 bb bb bb bb
12.1	587
	588
87.10	589	==== 2.3.2.10 MOD~=10 (PWM input capture and output mode，Since firmware v1.2)(% style="display:none" %) (%%) ====
65.1	590
87.10	591
74.8	592	(% style="color:red" %)Note: Firmware not release, contact Dragino for testing.
74.3	593
65.1	594	In this mode, the uplink can perform PWM input capture, and the downlink can perform PWM output.
	595
74.3	596	[[It should be noted when using PWM mode.>>\|\|anchor="H2.3.3.12A0PWMMOD"]]
65.1	597
69.1	598
65.1	599	===== 2.3.2.10.a Uplink, PWM input capture =====
	600
74.3	601
65.1	602	[[image:image-20230817172209-2.png\|\|height="439" width="683"]]
	603
87.40	604	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:515px" %)
87.24	605	\|(% style="background-color:#4f81bd; color:white; width:50px" %)Size(bytes)\|(% style="background-color:#4f81bd; color:white; width:20px" %)2\|(% style="background-color:#4f81bd; color:white; width:100px" %)2\|(% style="background-color:#4f81bd; color:white; width:50px" %)2\|(% style="background-color:#4f81bd; color:white; width:135px" %)1\|(% style="background-color:#4f81bd; color:white; width:70px" %)2\|(% style="background-color:#4f81bd; color:white; width:90px" %)2
65.1	606	\|Value\|Bat\|(% style="width:191px" %)(((
	607	Temperature(DS18B20)(PC13)
	608	)))\|(% style="width:78px" %)(((
	609	ADC(PA4)
	610	)))\|(% style="width:135px" %)(((
	611	PWM_Setting
	612	&Digital Interrupt(PA8)
	613	)))\|(% style="width:70px" %)(((
	614	Pulse period
	615	)))\|(% style="width:89px" %)(((
	616	Duration of high level
	617	)))
	618
	619	[[image:image-20230817170702-1.png\|\|height="161" width="1044"]]
	620
	621
72.1	622	When the device detects the following PWM signal ,decoder will converts the pulse period and high-level duration to frequency and duty cycle.
65.1	623
74.4	624	Frequency：
65.1	625
72.1	626	(% class="MsoNormal" %)
74.4	627	(% lang="EN-US" %)If (% style="background-attachment:initial; background-clip:initial; background-image:initial; background-origin:initial; background-position:initial; background-repeat:initial; background-size:initial; color:blue; font-family:Arial,sans-serif" %)AT+PWMSET(%%)=0, (% lang="EN-US" %)Frequency= 1000000/(%%)Pulse period（HZ）;
65.1	628
72.1	629	(% class="MsoNormal" %)
74.4	630	(% lang="EN-US" %)If (% style="background-attachment:initial; background-clip:initial; background-image:initial; background-origin:initial; background-position:initial; background-repeat:initial; background-size:initial; color:blue; font-family:Arial,sans-serif" %)AT+PWMSET(%%)=1, (% lang="EN-US" %)Frequency= 1000/(%%)Pulse period（HZ）;
72.1	631
74.4	632
72.1	633	(% class="MsoNormal" %)
74.4	634	Duty cycle:
72.1	635
	636	Duty cycle= Duration of high level/ Pulse period*100 ~(%).
	637
	638	[[image:image-20230818092200-1.png\|\|height="344" width="627"]]
	639
87.10	640
77.1	641	===== 2.3.2.10.b Uplink, PWM output =====
72.1	642
87.10	643
77.1	644	[[image:image-20230817172209-2.png\|\|height="439" width="683"]]
65.1	645
79.1	646	(% style="background-attachment:initial; background-clip:initial; background-image:initial; background-origin:initial; background-position:initial; background-repeat:initial; background-size:initial; color:blue; font-family:Arial,sans-serif" %)AT+PWMOUT=a,b,c
74.3	647
79.1	648	a is the time delay of the output, the unit is ms.
75.1	649
79.1	650	b is the output frequency, the unit is HZ.
75.1	651
79.1	652	c is the duty cycle of the output, the unit is %.
75.1	653
79.1	654	(% style="background-attachment:initial; background-clip:initial; background-image:initial; background-origin:initial; background-position:initial; background-repeat:initial; background-size:initial; color:blue; font-family:Arial,sans-serif" %)Downlink(%%): (% style="color:#037691" %)0B 01 bb cc aa
75.1	655
79.1	656	aa is the time delay of the output, the unit is ms.
	657
	658	bb is the output frequency, the unit is HZ.
	659
	660	cc is the duty cycle of the output, the unit is %.
	661
	662
	663	For example, send a AT command: AT+PWMOUT=65535,1000,50 The PWM is always out, the frequency is 1000HZ, and the duty cycle is 50.
	664
	665	The oscilloscope displays as follows:
	666
87.10	667	[[image:image-20231213102404-1.jpeg\|\|height="688" width="821"]]
79.1	668
	669
75.1	670	===== 2.3.2.10.c Downlink, PWM output =====
	671
	672
65.1	673	[[image:image-20230817173800-3.png\|\|height="412" width="685"]]
	674
	675	Downlink: (% style="color:#037691" %)0B xx xx xx yy zz zz
	676
	677	xx xx xx is the output frequency, the unit is HZ.
	678
	679	yy is the duty cycle of the output, the unit is %.
	680
	681	zz zz is the time delay of the output, the unit is ms.
	682
	683
	684	For example, send a downlink command: 0B 00 61 A8 32 13 88, the frequency is 25KHZ, the duty cycle is 50, and the output time is 5 seconds.
	685
	686	The oscilloscope displays as follows:
	687
87.10	688	[[image:image-20230817173858-5.png\|\|height="634" width="843"]]
65.1	689
	690
89.1	691
	692	==== 2.3.2.11 MOD~=11 (TEMP117) ====
	693
	694
	695	In this mode, uplink payload includes in total 11 bytes. Uplink packets use FPORT=2.
	696
	697	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:517px" %)
	698	\|(% style="background-color:#4f81bd; color:white; width:50px" %)Size(bytes)\|(% style="background-color:#4f81bd; color:white; width:20px" %)2\|(% style="background-color:#4f81bd; color:white; width:100px" %)2\|(% style="background-color:#4f81bd; color:white; width:50px" %)2\|(% style="background-color:#4f81bd; color:white; width:90px" %)1\|(% style="background-color:#4f81bd; color:white; width:128px" %)2\|(% style="background-color:#4f81bd; color:white; width:79px" %)2
	699	\|Value\|Bat\|(% style="width:191px" %)(((
	700	Temperature(DS18B20)(PC13)
	701	)))\|(% style="width:78px" %)(((
	702	ADC(PA4)
	703	)))\|(% style="width:216px" %)(((
	704	Digital in(PB15)&Digital Interrupt(PA8)
	705	)))\|(% style="width:308px" %)(((
96.1	706	Temperature
	707
	708	(TEMP117)
89.1	709	)))\|(% style="width:154px" %)(((
96.1	710	Reserved position, meaningless
	711
	712	(0x0000)
89.1	713	)))
	714
96.1	715	[[image:image-20240717113113-1.png\|\|height="352" width="793"]]
89.1	716
96.1	717	Connection:
89.1	718
96.1	719	[[image:image-20240717141528-2.jpeg\|\|height="430" width="654"]]
89.1	720
	721
96.1	722	==== 2.3.2.12 MOD~=12 (Count+SHT31) ====
89.1	723
	724
96.1	725	This mode has total 11 bytes. As shown below:
	726
	727	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:517px" %)
	728	\|=(% style="width: 86px; background-color: rgb(79, 129, 189); color: white;" %)Size(bytes)\|=(% style="width: 86px; background-color: rgb(79, 129, 189); color: white;" %)2\|=(% style="width: 86px; background-color: rgb(79, 129, 189); color: white;" %)2\|=(% style="width: 86px; background-color: rgb(79, 129, 189); color: white;" %)2\|=(% style="width: 86px; background-color: rgb(79, 129, 189); color: white;" %)1\|=(% style="width: 86px; background-color: rgb(79, 129, 189); color: white;" %)4
	729	\|Value\|BAT\|(% style="width:86px" %)(((
97.1	730	Temperature_SHT31
96.1	731	)))\|(% style="width:86px" %)(((
97.1	732	Humidity_SHT31
96.1	733	)))\|(% style="width:86px" %)(((
	734	Digital in(PB15)
	735	)))\|(% style="width:86px" %)(((
	736	Count(PA8)
	737	)))
	738
	739	[[image:image-20240717150948-5.png\|\|height="389" width="979"]]
	740
	741	Wiring example:
	742
	743	[[image:image-20240717152224-6.jpeg\|\|height="359" width="680"]]
	744
	745
14.1	746	=== 2.3.3 Decode payload ===
	747
43.45	748
12.1	749	While using TTN V3 network, you can add the payload format to decode the payload.
	750
	751	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656378466788-734.png?rev=1.1\|\|alt="1656378466788-734.png"]]
	752
	753	The payload decoder function for TTN V3 are here:
	754
87.4	755	SN50v3-LB/LS TTN V3 Payload Decoder: [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>url:https://github.com/dragino/dragino-end-node-decoder]]
12.1	756
	757
14.1	758	==== 2.3.3.1 Battery Info ====
2.1	759
43.45	760
87.4	761	Check the battery voltage for SN50v3-LB/LS.
2.1	762
	763	Ex1: 0x0B45 = 2885mV
	764
	765	Ex2: 0x0B49 = 2889mV
	766
	767
14.1	768	==== 2.3.3.2 Temperature (DS18B20) ====
2.1	769
43.45	770
42.1	771	If there is a DS18B20 connected to PC13 pin. The temperature will be uploaded in the payload.
2.1	772
43.45	773	More DS18B20 can check the [[3 DS18B20 mode>>\|\|anchor="H2.3.2.4MOD3D4283xDS18B2029"]]
14.1	774
43.41	775	(% style="color:blue" %)Connection:
14.1	776
26.2	777	[[image:image-20230512180718-8.png\|\|height="538" width="647"]]
14.1	778
43.46	779
43.41	780	(% style="color:blue" %)Example:
2.1	781
	782	If payload is: 0105H: (0105 & 8000 == 0), temp = 0105H /10 = 26.1 degree
	783
	784	If payload is: FF3FH : (FF3F & 8000 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.
	785
	786	（FF3F & 8000：Judge whether the highest bit is 1, when the highest bit is 1, it is negative）
	787
	788
14.1	789	==== 2.3.3.3 Digital Input ====
2.1	790
43.46	791
26.2	792	The digital input for pin PB15,
2.1	793
26.2	794	* When PB15 is high, the bit 1 of payload byte 6 is 1.
	795	* When PB15 is low, the bit 1 of payload byte 6 is 0.
2.1	796
26.2	797	(% class="wikigeneratedid" id="H2.3.3.4A0AnalogueDigitalConverter28ADC29" %)
	798	(((
36.1	799	When the digital interrupt pin is set to AT+INTMODx=0, this pin is used as a digital input pin.
	800
43.46	801	(% style="color:red" %)Note: The maximum voltage input supports 3.6V.
	802
	803
26.2	804	)))
	805
14.1	806	==== 2.3.3.4 Analogue Digital Converter (ADC) ====
2.1	807
43.46	808
53.1	809	The measuring range of the ADC is only about 0.1V to 1.1V The voltage resolution is about 0.24mv.
2.1	810
53.1	811	When the measured output voltage of the sensor is not within the range of 0.1V and 1.1V, the output voltage terminal of the sensor shall be divided The example in the following figure is to reduce the output voltage of the sensor by three times If it is necessary to reduce more times, calculate according to the formula in the figure and connect the corresponding resistance in series.
14.1	812
26.2	813	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220628150112-1.png?width=285&height=241&rev=1.1\|\|alt="image-20220628150112-1.png" height="241" width="285"]]
14.1	814
44.2	815
43.46	816	(% style="color:red" %)Note: If the ADC type sensor needs to be powered by SN50_v3, it is recommended to use +5V to control its switch.Only sensors with low power consumption can be powered with VDD.
14.1	817
43.1	818
59.1	819	The position of PA5 on the hardware after LSN50 v3.3 is changed to the position shown in the figure below, and the collected voltage becomes one-sixth of the original.
	820
	821	[[image:image-20230811113449-1.png\|\|height="370" width="608"]]
	822
87.10	823
	824
14.1	825	==== 2.3.3.5 Digital Interrupt ====
	826
43.46	827
87.4	828	Digital Interrupt refers to pin PA8, and there are different trigger methods. When there is a trigger, the SN50v3-LB/LS will send a packet to the server.
14.1	829
43.44	830	(% style="color:blue" %) Interrupt connection method:
14.1	831
36.1	832	[[image:image-20230513105351-5.png\|\|height="147" width="485"]]
14.1	833
43.46	834
43.8	835	(% style="color:blue" %)Example to use with door sensor :
14.1	836
	837	The door sensor is shown at right. It is a two wire magnetic contact switch used for detecting the open/close status of doors or windows.
	838
	839	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379210849-860.png?rev=1.1\|\|alt="1656379210849-860.png"]]
	840
87.4	841	When the two pieces are close to each other, the 2 wire output will be short or open (depending on the type), while if the two pieces are away from each other, the 2 wire output will be the opposite status. So we can use SN50v3-LB/LS interrupt interface to detect the status for the door or window.
14.1	842
	843
43.46	844	(% style="color:blue" %)Below is the installation example:
	845
87.4	846	Fix one piece of the magnetic sensor to the door and connect the two pins to SN50v3-LB/LS as follows:
14.1	847
	848	* (((
87.4	849	One pin to SN50v3-LB/LS's PA8 pin
14.1	850	)))
	851	* (((
87.4	852	The other pin to SN50v3-LB/LS's VDD pin
14.1	853	)))
	854
36.1	855	Install the other piece to the door. Find a place where the two pieces will be close to each other when the door is closed. For this particular magnetic sensor, when the door is closed, the output will be short, and PA8 will be at the VCC voltage.
14.1	856
43.46	857	Door sensors have two types: (% style="color:blue" %) NC (Normal close)(%%) and (% style="color:blue" %)NO (normal open)(%%). The connection for both type sensors are the same. But the decoding for payload are reverse, user need to modify this in the IoT Server decoder.
14.1	858
36.1	859	When door sensor is shorted, there will extra power consumption in the circuit, the extra current is 3v3/R14 = 3v3/1Mohm = 3uA which can be ignored.
14.1	860
	861	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379283019-229.png?rev=1.1\|\|alt="1656379283019-229.png"]]
	862
	863	The above photos shows the two parts of the magnetic switch fitted to a door.
	864
	865	The software by default uses the falling edge on the signal line as an interrupt. We need to modify it to accept both the rising edge (0v ~-~-> VCC , door close) and the falling edge (VCC ~-~-> 0v , door open) as the interrupt.
	866
	867	The command is:
	868
44.2	869	(% style="color:blue" %)AT+INTMOD1=1 (%%) ~/~/ (more info about INMOD please refer [[AT Command Manual>>url:http://www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/&file=DRAGINO_LSN50_AT_Commands_v1.5.1.pdf]]. )
14.1	870
	871	Below shows some screen captures in TTN V3:
	872
	873	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379339508-835.png?rev=1.1\|\|alt="1656379339508-835.png"]]
	874
43.47	875
44.4	876	In MOD=1, user can use byte 6 to see the status for door open or close. TTN V3 decoder is as below:
14.1	877
	878	door= (bytes[6] & 0x80)? "CLOSE":"OPEN";
	879
	880
26.2	881	==== 2.3.3.6 I2C Interface (SHT20 & SHT31) ====
14.1	882
43.47	883
26.2	884	The SDA and SCK are I2C interface lines. You can use these to connect to an I2C device and get the sensor data.
14.1	885
40.1	886	We have made an example to show how to use the I2C interface to connect to the SHT20/ SHT31 Temperature and Humidity Sensor.
14.1	887
87.4	888	(% style="color:red" %)Notice: Different I2C sensors have different I2C commands set and initiate process, if user want to use other I2C sensors, User need to re-write the source code to support those sensors. SHT20/ SHT31 code in SN50v3-LB/LS will be a good reference.
14.1	889
44.2	890
14.1	891	Below is the connection to SHT20/ SHT31. The connection is as below:
	892
52.1	893	[[image:image-20230610170152-2.png\|\|height="501" width="846"]]
36.1	894
44.4	895
14.1	896	The device will be able to get the I2C sensor data now and upload to IoT Server.
	897
	898	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379664142-345.png?rev=1.1\|\|alt="1656379664142-345.png"]]
	899
	900	Convert the read byte to decimal and divide it by ten.
	901
2.1	902	Example:
	903
14.1	904	Temperature: Read:0116(H) = 278(D) Value: 278 /10=27.8℃;
2.1	905
14.1	906	Humidity: Read:0248(H)=584(D) Value: 584 / 10=58.4, So 58.4%
2.1	907
14.1	908	If you want to use other I2C device, please refer the SHT20 part source code as reference.
2.1	909
	910
14.1	911	==== 2.3.3.7 Distance Reading ====
2.1	912
43.48	913
43.42	914	Refer [[Ultrasonic Sensor section>>\|\|anchor="H2.3.3.8UltrasonicSensor"]].
14.1	915
	916
	917	==== 2.3.3.8 Ultrasonic Sensor ====
	918
43.48	919
26.2	920	This Fundamental Principles of this sensor can be found at this link: [[https:~~/~~/wiki.dfrobot.com/Weather_-_proof_Ultrasonic_Sensor_with_Separate_Probe_SKU~~_~~__SEN0208>>url:https://wiki.dfrobot.com/Weather_-_proof_Ultrasonic_Sensor_with_Separate_Probe_SKU___SEN0208]]
14.1	921
87.4	922	The SN50v3-LB/LS detects the pulse width of the sensor and converts it to mm output. The accuracy will be within 1 centimeter. The usable range (the distance between the ultrasonic probe and the measured object) is between 24cm and 600cm.
14.1	923
43.44	924	The working principle of this sensor is similar to the (% style="color:blue" %)HC-SR04(%%) ultrasonic sensor.
36.1	925
14.1	926	The picture below shows the connection:
	927
36.1	928	[[image:image-20230512173903-6.png\|\|height="596" width="715"]]
14.1	929
43.50	930
87.4	931	Connect to the SN50v3-LB/LS and run (% style="color:blue" %)AT+MOD=2(%%) to switch to ultrasonic mode (ULT).
14.1	932
	933	The ultrasonic sensor uses the 8^^th^^ and 9^^th^^ byte for the measurement value.
	934
	935	Example:
	936
	937	Distance: Read: 0C2D(Hex) = 3117(D) Value: 3117 mm=311.7 cm
	938
	939
	940	==== 2.3.3.9 Battery Output - BAT pin ====
	941
43.50	942
87.4	943	The BAT pin of SN50v3-LB/LS is connected to the Battery directly. If users want to use BAT pin to power an external sensor. User need to make sure the external sensor is of low power consumption. Because the BAT pin is always open. If the external sensor is of high power consumption. the battery of SN50v3-LB/LS will run out very soon.
14.1	944
	945
	946	==== 2.3.3.10 +5V Output ====
	947
43.50	948
87.4	949	SN50v3-LB/LS will enable +5V output before all sampling and disable the +5v after all sampling.
14.1	950
	951	The 5V output time can be controlled by AT Command.
	952
43.9	953	(% style="color:blue" %)AT+5VT=1000
14.1	954
	955	Means set 5V valid time to have 1000ms. So the real 5V output will actually have 1000ms + sampling time for other sensors.
	956
44.4	957	By default the AT+5VT=500. If the external sensor which require 5v and require more time to get stable state, user can use this command to increase the power ON duration for this sensor.
14.1	958
	959
	960	==== 2.3.3.11 BH1750 Illumination Sensor ====
	961
43.50	962
14.1	963	MOD=1 support this sensor. The sensor value is in the 8^^th^^ and 9^^th^^ bytes.
	964
40.1	965	[[image:image-20230512172447-4.png\|\|height="416" width="712"]]
14.1	966
43.51	967
40.1	968	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220628110012-12.png?rev=1.1\|\|alt="image-20220628110012-12.png" height="361" width="953"]]
14.1	969
	970
65.1	971	==== 2.3.3.12 PWM MOD ====
14.1	972
43.51	973
69.1	974	* (((
	975	The maximum voltage that the SDA pin of SN50v3 can withstand is 3.6V, and it cannot exceed this voltage value, otherwise the chip may be burned.
	976	)))
	977	* (((
	978	If the PWM pin connected to the SDA pin cannot maintain a high level when it is not working, you need to remove the resistor R2 or replace it with a resistor with a larger resistance, otherwise a sleep current of about 360uA will be generated. The position of the resistor is shown in the figure below:
	979	)))
	980
	981	[[image:image-20230817183249-3.png\|\|height="320" width="417"]]
	982
	983	* (((
	984	The signal captured by the input should preferably be processed by hardware filtering and then connected in. The software processing method is to capture four values, discard the first captured value, and then take the middle value of the second, third, and fourth captured values.
	985	)))
	986	* (((
74.2	987	Since the device can only detect a pulse period of 50ms when [[AT+PWMSET=0>>\|\|anchor="H3.3.8PWMsetting"]] (counting in microseconds), it is necessary to change the value of PWMSET according to the frequency of input capture.
74.8	988	)))
	989	* (((
76.1	990	PWM Input allows low power consumption. PWM Output to achieve real-time control, you need to go to class C. Power consumption will not be low.
70.1	991
74.8	992	For PWM Output Feature, there are two consideration to see if the device can be powered by battery or have to be powered by external DC.
74.5	993
87.4	994	a) If real-time control output is required, the SN50v3-LB/LS is already operating in class C and an external power supply must be used.
74.8	995
76.1	996	b) If the output duration is more than 30 seconds, better to use external power source.
87.4	997	)))
74.8	998
65.1	999	==== 2.3.3.13 Working MOD ====
	1000
	1001
14.1	1002	The working MOD info is contained in the Digital in & Digital Interrupt byte (7^^th^^ Byte).
	1003
	1004	User can use the 3^^rd^^ ~~ 7^^th^^ bit of this byte to see the working mod:
	1005
	1006	Case 7^^th^^ Byte >> 2 & 0x1f:
	1007
	1008	* 0: MOD1
	1009	* 1: MOD2
	1010	* 2: MOD3
	1011	* 3: MOD4
	1012	* 4: MOD5
	1013	* 5: MOD6
36.1	1014	* 6: MOD7
	1015	* 7: MOD8
	1016	* 8: MOD9
65.1	1017	* 9: MOD10
14.1	1018
2.1	1019	== 2.4 Payload Decoder file ==
	1020
	1021
	1022	In TTN, use can add a custom payload so it shows friendly reading
	1023
	1024	In the page (% style="color:#037691" %)Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder(%%) to add the decoder from:
	1025
40.1	1026	[[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/SN50_v3-LB>>https://github.com/dragino/dragino-end-node-decoder/tree/main/SN50_v3-LB]]
2.1	1027
	1028
15.1	1029	== 2.5 Frequency Plans ==
2.1	1030
	1031
87.30	1032	The SN50v3-LB/LS uses OTAA mode and below frequency plans by default. Each frequency band use different firmware, user update the firmware to the corresponding band for their country.
2.1	1033
	1034	[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]
	1035
	1036
87.4	1037	= 3. Configure SN50v3-LB/LS =
2.1	1038
	1039	== 3.1 Configure Methods ==
	1040
	1041
87.4	1042	SN50v3-LB/LS supports below configure method:
2.1	1043
	1044	* AT Command via Bluetooth Connection (Recommended): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
	1045	* AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].
	1046	* LoRaWAN Downlink. Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
	1047
	1048	== 3.2 General Commands ==
	1049
	1050
	1051	These commands are to configure:
	1052
	1053	* General system settings like: uplink interval.
	1054	* LoRaWAN protocol & radio related command.
	1055
	1056	They are same for all Dragino Devices which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:
	1057
	1058	[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
	1059
	1060
87.4	1061	== 3.3 Commands special design for SN50v3-LB/LS ==
2.1	1062
	1063
87.4	1064	These commands only valid for SN50v3-LB/LS, as below:
2.1	1065
	1066
	1067	=== 3.3.1 Set Transmit Interval Time ===
	1068
43.51	1069
2.1	1070	Feature: Change LoRaWAN End Node Transmit Interval.
	1071
	1072	(% style="color:blue" %)AT Command: AT+TDC
	1073
	1074	(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
87.11	1075	\|=(% style="width: 156px;background-color:#4F81BD;color:white" %)Command Example\|=(% style="width: 137px;background-color:#4F81BD;color:white" %)Function\|=(% style="background-color:#4F81BD;color:white" %)Response
2.1	1076	\|(% style="width:156px" %)AT+TDC=?\|(% style="width:137px" %)Show current transmit Interval\|(((
	1077	30000
	1078	OK
	1079	the interval is 30000ms = 30s
	1080	)))
	1081	\|(% style="width:156px" %)AT+TDC=60000\|(% style="width:137px" %)Set Transmit Interval\|(((
	1082	OK
	1083	Set transmit interval to 60000ms = 60 seconds
	1084	)))
	1085
	1086	(% style="color:blue" %)Downlink Command: 0x01
	1087
	1088	Format: Command Code (0x01) followed by 3 bytes time value.
	1089
	1090	If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
	1091
	1092	* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
	1093	* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
	1094
	1095	=== 3.3.2 Get Device Status ===
	1096
43.52	1097
40.1	1098	Send a LoRaWAN downlink to ask the device to send its status.
2.1	1099
44.4	1100	(% style="color:blue" %)Downlink Payload: 0x26 01
2.1	1101
44.4	1102	Sensor will upload Device Status via FPORT=5. See payload section for detail.
2.1	1103
	1104
36.1	1105	=== 3.3.3 Set Interrupt Mode ===
2.1	1106
43.52	1107
2.1	1108	Feature, Set Interrupt mode for GPIO_EXIT.
	1109
87.15	1110	(% style="color:blue" %)AT Command: AT+INTMOD1,AT+INTMOD2,AT+INTMOD3
2.1	1111
	1112	(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
87.11	1113	\|=(% style="width: 155px;background-color:#4F81BD;color:white" %)Command Example\|=(% style="width: 197px;background-color:#4F81BD;color:white" %)Function\|=(% style="width: 158px;background-color:#4F81BD;color:white" %)Response
36.1	1114	\|(% style="width:154px" %)AT+INTMOD1=?\|(% style="width:196px" %)Show current interrupt mode\|(% style="width:157px" %)(((
2.1	1115	0
	1116	OK
	1117	the mode is 0 =Disable Interrupt
	1118	)))
36.1	1119	\|(% style="width:154px" %)AT+INTMOD1=2\|(% style="width:196px" %)(((
2.1	1120	Set Transmit Interval
	1121	0. (Disable Interrupt),
	1122	~1. (Trigger by rising and falling edge)
	1123	2. (Trigger by falling edge)
	1124	3. (Trigger by rising edge)
	1125	)))\|(% style="width:157px" %)OK
36.1	1126	\|(% style="width:154px" %)AT+INTMOD2=3\|(% style="width:196px" %)(((
	1127	Set Transmit Interval
	1128	trigger by rising edge.
	1129	)))\|(% style="width:157px" %)OK
	1130	\|(% style="width:154px" %)AT+INTMOD3=0\|(% style="width:196px" %)Disable Interrupt\|(% style="width:157px" %)OK
	1131
2.1	1132	(% style="color:blue" %)Downlink Command: 0x06
	1133
	1134	Format: Command Code (0x06) followed by 3 bytes.
	1135
	1136	This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
	1137
36.1	1138	* Example 1: Downlink Payload: 06000000 ~-~--> AT+INTMOD1=0
	1139	* Example 2: Downlink Payload: 06000003 ~-~--> AT+INTMOD1=3
	1140	* Example 3: Downlink Payload: 06000102 ~-~--> AT+INTMOD2=2
	1141	* Example 4: Downlink Payload: 06000201 ~-~--> AT+INTMOD3=1
2.1	1142
36.1	1143	=== 3.3.4 Set Power Output Duration ===
	1144
43.52	1145
36.1	1146	Control the output duration 5V . Before each sampling, device will
	1147
	1148	~1. first enable the power output to external sensor,
	1149
	1150	2. keep it on as per duration, read sensor value and construct uplink payload
	1151
	1152	3. final, close the power output.
	1153
	1154	(% style="color:blue" %)AT Command: AT+5VT
	1155
	1156	(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
87.11	1157	\|=(% style="width: 155px;background-color:#4F81BD;color:white" %)Command Example\|=(% style="width: 197px;background-color:#4F81BD;color:white" %)Function\|=(% style="width: 158px;background-color:#4F81BD;color:white" %)Response
36.1	1158	\|(% style="width:154px" %)AT+5VT=?\|(% style="width:196px" %)Show 5V open time.\|(% style="width:157px" %)(((
	1159	500(default)
	1160	OK
	1161	)))
	1162	\|(% style="width:154px" %)AT+5VT=1000\|(% style="width:196px" %)(((
	1163	Close after a delay of 1000 milliseconds.
	1164	)))\|(% style="width:157px" %)OK
	1165
	1166	(% style="color:blue" %)Downlink Command: 0x07
	1167
	1168	Format: Command Code (0x07) followed by 2 bytes.
	1169
	1170	The first and second bytes are the time to turn on.
	1171
40.1	1172	* Example 1: Downlink Payload: 070000 ~-~--> AT+5VT=0
	1173	* Example 2: Downlink Payload: 0701F4 ~-~--> AT+5VT=500
36.1	1174
	1175	=== 3.3.5 Set Weighing parameters ===
	1176
43.52	1177
37.1	1178	Feature: Working mode 5 is effective, weight initialization and weight factor setting of HX711.
36.1	1179
	1180	(% style="color:blue" %)AT Command: AT+WEIGRE,AT+WEIGAP
	1181
	1182	(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
87.11	1183	\|=(% style="width: 155px;background-color:#4F81BD;color:white" %)Command Example\|=(% style="width: 197px;background-color:#4F81BD;color:white" %)Function\|=(% style="width: 158px;background-color:#4F81BD;color:white" %)Response
37.1	1184	\|(% style="width:154px" %)AT+WEIGRE\|(% style="width:196px" %)Weight is initialized to 0.\|(% style="width:157px" %)OK
87.16	1185	\|(% style="width:154px" %)AT+WEIGAP=?\|(% style="width:196px" %)400.0\|(% style="width:157px" %)OK(default)
37.1	1186	\|(% style="width:154px" %)AT+WEIGAP=400.3\|(% style="width:196px" %)Set the factor to 400.3.\|(% style="width:157px" %)OK
36.1	1187
	1188	(% style="color:blue" %)Downlink Command: 0x08
	1189
37.1	1190	Format: Command Code (0x08) followed by 2 bytes or 4 bytes.
36.1	1191
37.1	1192	Use AT+WEIGRE when the first byte is 1, only 1 byte. When it is 2, use AT+WEIGAP, there are 3 bytes.
36.1	1193
37.1	1194	The second and third bytes are multiplied by 10 times to be the AT+WEIGAP value.
36.1	1195
37.1	1196	* Example 1: Downlink Payload: 0801 ~-~--> AT+WEIGRE
	1197	* Example 2: Downlink Payload: 08020FA3 ~-~--> AT+WEIGAP=400.3
	1198	* Example 3: Downlink Payload: 08020FA0 ~-~--> AT+WEIGAP=400.0
	1199
36.1	1200	=== 3.3.6 Set Digital pulse count value ===
	1201
43.52	1202
36.1	1203	Feature: Set the pulse count value.
	1204
37.1	1205	Count 1 is PA8 pin of mode 6 and mode 9. Count 2 is PA4 pin of mode 9.
	1206
36.1	1207	(% style="color:blue" %)AT Command: AT+SETCNT
	1208
87.41	1209	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
87.11	1210	\|=(% style="width: 155px;background-color:#4F81BD;color:white" %)Command Example\|=(% style="width: 197px;background-color:#4F81BD;color:white" %)Function\|=(% style="width: 158px;background-color:#4F81BD;color:white" %)Response
36.1	1211	\|(% style="width:154px" %)AT+SETCNT=1,100\|(% style="width:196px" %)Initialize the count value 1 to 100.\|(% style="width:157px" %)OK
	1212	\|(% style="width:154px" %)AT+SETCNT=2,0\|(% style="width:196px" %)Initialize the count value 2 to 0.\|(% style="width:157px" %)OK
	1213
	1214	(% style="color:blue" %)Downlink Command: 0x09
	1215
	1216	Format: Command Code (0x09) followed by 5 bytes.
	1217
	1218	The first byte is to select which count value to initialize, and the next four bytes are the count value to be initialized.
	1219
	1220	* Example 1: Downlink Payload: 090100000000 ~-~--> AT+SETCNT=1,0
37.1	1221	* Example 2: Downlink Payload: 0902000003E8 ~-~--> AT+SETCNT=2,1000
36.1	1222
	1223	=== 3.3.7 Set Workmode ===
	1224
43.52	1225
37.1	1226	Feature: Switch working mode.
36.1	1227
	1228	(% style="color:blue" %)AT Command: AT+MOD
	1229
87.41	1230	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
87.11	1231	\|=(% style="width: 155px;background-color:#4F81BD;color:white" %)Command Example\|=(% style="width: 197px;background-color:#4F81BD;color:white" %)Function\|=(% style="width: 158px;background-color:#4F81BD;color:white" %)Response
36.1	1232	\|(% style="width:154px" %)AT+MOD=?\|(% style="width:196px" %)Get the current working mode.\|(% style="width:157px" %)(((
	1233	OK
	1234	)))
	1235	\|(% style="width:154px" %)AT+MOD=4\|(% style="width:196px" %)Set the working mode to 3DS18B20s.\|(% style="width:157px" %)(((
	1236	OK
	1237	Attention:Take effect after ATZ
	1238	)))
	1239
	1240	(% style="color:blue" %)Downlink Command: 0x0A
	1241
	1242	Format: Command Code (0x0A) followed by 1 bytes.
	1243
	1244	* Example 1: Downlink Payload: 0A01 ~-~--> AT+MOD=1
	1245	* Example 2: Downlink Payload: 0A04 ~-~--> AT+MOD=4
	1246
72.1	1247	=== 3.3.8 PWM setting ===
	1248
74.5	1249
87.24	1250	Feature: Set the time acquisition unit for PWM input capture.
72.1	1251
	1252	(% style="color:blue" %)AT Command: AT+PWMSET
	1253
87.41	1254	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
87.17	1255	\|=(% style="width: 155px;background-color:#4F81BD;color:white" %)Command Example\|=(% style="width: 225px; background-color: #4F81BD;color:white" %)Function\|=(% style="width: 130px; background-color:#4F81BD;color:white" %)Response
77.1	1256	\|(% style="width:154px" %)AT+PWMSET=?\|(% style="width:223px" %)0\|(% style="width:130px" %)(((
72.1	1257	0(default)
	1258	OK
	1259	)))
77.1	1260	\|(% style="width:154px" %)AT+PWMSET=0\|(% style="width:223px" %)The unit of PWM capture time is microsecond. The capture frequency range is between 20HZ and 100000HZ. \|(% style="width:130px" %)(((
72.1	1261	OK
	1262
	1263	)))
77.1	1264	\|(% style="width:154px" %)AT+PWMSET=1\|(% style="width:223px" %)The unit of PWM capture time is millisecond. The capture frequency range is between 5HZ and 250HZ. \|(% style="width:130px" %)OK
72.1	1265
	1266	(% style="color:blue" %)Downlink Command: 0x0C
	1267
	1268	Format: Command Code (0x0C) followed by 1 bytes.
	1269
	1270	* Example 1: Downlink Payload: 0C00 ~-~--> AT+PWMSET=0
	1271	* Example 2: Downlink Payload: 0C01 ~-~--> AT+PWMSET=1
	1272
87.24	1273	Feature: Set PWM output time, output frequency and output duty cycle.
	1274
76.1	1275	(% style="color:blue" %)AT Command: AT+PWMOUT
75.1	1276
87.41	1277	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
87.21	1278	\|=(% style="width: 183px; background-color: #4F81BD;color:white" %)Command Example\|=(% style="width: 193px; background-color: #4F81BD;color:white" %)Function\|=(% style="width: 134px; background-color: #4F81BD;color:white" %)Response
77.1	1279	\|(% style="width:183px" %)AT+PWMOUT=?\|(% style="width:193px" %)0\|(% style="width:137px" %)(((
76.1	1280	0,0,0(default)
	1281	OK
	1282	)))
77.1	1283	\|(% style="width:183px" %)AT+PWMOUT=0,0,0\|(% style="width:193px" %)The default is PWM input detection\|(% style="width:137px" %)(((
76.1	1284	OK
	1285
	1286	)))
77.1	1287	\|(% style="width:183px" %)AT+PWMOUT=5,1000,50\|(% style="width:193px" %)(((
	1288	The PWM output time is 5ms, the output frequency is 1000HZ, and the output duty cycle is 50%.
75.1	1289
77.1	1290
	1291	)))\|(% style="width:137px" %)(((
	1292	OK
	1293	)))
	1294
87.41	1295	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
87.18	1296	\|=(% style="width: 155px; background-color:#4F81BD;color:white" %)Command Example\|=(% style="width: 112px; background-color:#4F81BD;color:white" %)Function\|=(% style="width: 242px; background-color:#4F81BD;color:white" %)parameters
77.1	1297	\|(% colspan="1" rowspan="3" style="width:155px" %)(((
	1298	AT+PWMOUT=a,b,c
	1299
	1300
	1301	)))\|(% colspan="1" rowspan="3" style="width:112px" %)(((
79.1	1302	Set PWM output time, output frequency and output duty cycle.
	1303
	1304	(((
77.1	1305
	1306	)))
	1307
	1308	(((
	1309
	1310	)))
	1311	)))\|(% style="width:242px" %)(((
76.1	1312	a: Output time (unit: seconds)
77.1	1313	The value ranges from 0 to 65535.
	1314	When a=65535, PWM will always output.
	1315	)))
	1316	\|(% style="width:242px" %)(((
76.1	1317	b: Output frequency (unit: HZ)
77.1	1318	)))
	1319	\|(% style="width:242px" %)(((
	1320	c: Output duty cycle (unit: %)
	1321	The value ranges from 0 to 100.
76.1	1322	)))
	1323
77.1	1324	(% style="color:blue" %)Downlink Command: 0x0B01
76.1	1325
77.1	1326	Format: Command Code (0x0B01) followed by 6 bytes.
76.1	1327
87.19	1328	Downlink payload:0B01 bb cc aa ~-~--> AT+PWMOUT=a,b,c
76.1	1329
77.1	1330	* Example 1: Downlink Payload: 0B01 03E8 0032 0005 ~-~--> AT+PWMSET=5,1000,50
	1331	* Example 2: Downlink Payload: 0B01 07D0 003C 000A ~-~--> AT+PWMSET=10,2000,60
76.1	1332
79.1	1333	= 4. Battery & Power Cons =
	1334
	1335
87.6	1336	SN50v3-LB use ER26500 + SPC1520 battery pack and SN50v3-LS use 3000mAh Recharable Battery with Solar Panel. See below link for detail information about the battery info and how to replace.
2.1	1337
	1338	[[Battery Info & Power Consumption Analyze>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
	1339
	1340
	1341	= 5. OTA Firmware update =
	1342
	1343
	1344	(% class="wikigeneratedid" %)
87.4	1345	User can change firmware SN50v3-LB/LS to:
2.1	1346
	1347	* Change Frequency band/ region.
	1348	* Update with new features.
	1349	* Fix bugs.
	1350
52.2	1351	Firmware and changelog can be downloaded from : [[Firmware download link>>https://www.dropbox.com/sh/4rov7bcp6u28exp/AACt-wAySd4si5AXi8DBmvSca?dl=0]]
2.1	1352
44.4	1353	Methods to Update Firmware:
2.1	1354
53.3	1355	* (Recommanded way) OTA firmware update via wireless: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]
	1356	* Update through UART TTL interface: [[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]].
2.1	1357
	1358	= 6. FAQ =
	1359
87.4	1360	== 6.1 Where can i find source code of SN50v3-LB/LS? ==
2.1	1361
43.52	1362
17.1	1363	* [[Hardware Source Files>>https://github.com/dragino/Lora/tree/master/LSN50/v3.0]].
	1364	* [[Software Source Code & Compile instruction>>https://github.com/dragino/SN50v3]].
2.1	1365
87.4	1366	== 6.2 How to generate PWM Output in SN50v3-LB/LS? ==
55.2	1367
	1368
55.1	1369	See this document: [[Generate PWM Output on SN50v3>>https://www.dropbox.com/scl/fi/r3trcet2knujg40w0mgyn/Generate-PWM-Output-on-SN50v3.pdf?rlkey=rxsgmrhhrv62iiiwjq9sv10bn&dl=0]].
	1370
	1371
87.4	1372	== 6.3 How to put several sensors to a SN50v3-LB/LS? ==
57.1	1373
57.2	1374
87.4	1375	When we want to put several sensors to A SN50v3-LB/LS, the waterproof at the grand connector will become an issue. User can try to exchange the grand connector to below type.
57.1	1376
	1377	[[Reference Supplier>>https://www.yscableglands.com/cable-glands/nylon-cable-glands/cable-gland-rubber-seal.html]].
	1378
	1379	[[image:image-20230810121434-1.png\|\|height="242" width="656"]]
	1380
	1381
2.1	1382	= 7. Order Info =
	1383
	1384
87.9	1385	Part Number: (% style="color:blue" %)SN50v3-LB-XX-YY(%%) or (% style="color:blue" %)SN50v3-LS-XX-YY
2.1	1386
	1387	(% style="color:red" %)XX(%%): The default frequency band
11.1	1388
2.1	1389	* (% style="color:red" %)AS923(%%): LoRaWAN AS923 band
	1390	* (% style="color:red" %)AU915(%%): LoRaWAN AU915 band
	1391	* (% style="color:red" %)EU433(%%): LoRaWAN EU433 band
	1392	* (% style="color:red" %)EU868(%%): LoRaWAN EU868 band
	1393	* (% style="color:red" %)KR920(%%): LoRaWAN KR920 band
	1394	* (% style="color:red" %)US915(%%): LoRaWAN US915 band
	1395	* (% style="color:red" %)IN865(%%): LoRaWAN IN865 band
	1396	* (% style="color:red" %)CN470(%%): LoRaWAN CN470 band
	1397
10.1	1398	(% style="color:red" %)YY: (%%)Hole Option
2.1	1399
10.1	1400	* (% style="color:red" %)12(%%): With M12 waterproof cable hole
	1401	* (% style="color:red" %)16(%%): With M16 waterproof cable hole
	1402	* (% style="color:red" %)20(%%): With M20 waterproof cable hole
	1403	* (% style="color:red" %)NH(%%): No Hole
	1404
2.1	1405	= 8. Packing Info =
	1406
43.52	1407
2.1	1408	(% style="color:#037691" %)Package Includes:
	1409
87.4	1410	* SN50v3-LB or SN50v3-LS LoRaWAN Generic Node
2.1	1411
	1412	(% style="color:#037691" %)Dimension and weight:
	1413
	1414	* Device Size: cm
	1415	* Device Weight: g
	1416	* Package Size / pcs : cm
	1417	* Weight / pcs : g
	1418
	1419	= 9. Support =
	1420
	1421
	1422	* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
43.10	1423
41.4	1424	* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.cc>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.cc]]

Wiki source code of SN50v3-LB/LS -- LoRaWAN Sensor Node User Manual

Applications