Version 78.1 by Mengting Qiu on 2023/12/13 10:24
Show last authors
1 (% style="text-align:center" %)
2 [[image:image-20230515135611-1.jpeg||height="589" width="589"]]
3
4
5
6 **Table of Contents：**
7
8 {{toc/}}
9
10
11
12
13
14
15 = 1. Introduction =
16
17 == 1.1 What is SN50v3-LB LoRaWAN Generic Node ==
18
19
20 (% style="color:blue" %)**SN50V3-LB **(%%)LoRaWAN Sensor Node is a Long Range LoRa Sensor Node. It is designed for outdoor use and powered by (% style="color:blue" %)** 8500mA Li/SOCl2 battery**(%%) for long term use.SN50V3-LB is designed to facilitate developers to quickly deploy industrial level LoRa and IoT solutions. It help users to turn the idea into a practical application and make the Internet of Things a reality. It is easy to program, create and connect your things everywhere.
21
22 (% style="color:blue" %)**SN50V3-LB wireless part**(%%) is based on SX1262 allows the user to send data and reach extremely long ranges at low data-rates.It provides ultra-long range spread spectrum communication and high interference immunity whilst minimising current consumption.It targets professional wireless sensor network applications such as irrigation systems, smart metering, smart cities, and so on.
23
24 (% style="color:blue" %)**SN50V3-LB **(%%)has a powerful 48Mhz ARM microcontroller with 256KB flash and 64KB RAM. It has multiplex I/O pins to connect to different sensors.
25
26 (% style="color:blue" %)**SN50V3-LB**(%%) has a built-in BLE module, user can configure the sensor remotely via Mobile Phone. It also support OTA upgrade via private LoRa protocol for easy maintaining.
27
28 SN50V3-LB is the 3^^rd^^ generation of LSN50 series generic sensor node from Dragino. It is an (% style="color:blue" %)**open source project**(%%) and has a mature LoRaWAN stack and application software. User can use the pre-load software for their IoT projects or easily customize the software for different requirements.
29
30 == 1.2 ​Features ==
31
32
33 * LoRaWAN 1.0.3 Class A
34 * Ultra-low power consumption
35 * Open-Source hardware/software
36 * Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
37 * Support Bluetooth v5.1 and LoRaWAN remote configure
38 * Support wireless OTA update firmware
39 * Uplink on periodically
40 * Downlink to change configure
41 * 8500mAh Battery for long term use
42
43 == 1.3 Specification ==
44
45
46 (% style="color:#037691" %)**Common DC Characteristics:**
47
48 * Supply Voltage: built in 8500mAh Li-SOCI2 battery , 2.5v ~~ 3.6v
49 * Operating Temperature: -40 ~~ 85°C
50
51 (% style="color:#037691" %)**I/O Interface:**
52
53 * Battery output (2.6v ~~ 3.6v depends on battery)
54 * +5v controllable output
55 * 3 x Interrupt or Digital IN/OUT pins
56 * 3 x one-wire interfaces
57 * 1 x UART Interface
58 * 1 x I2C Interface
59
60 (% style="color:#037691" %)**LoRa Spec:**
61
62 * Frequency Range,  Band 1 (HF): 862 ~~ 1020 Mhz
63 * Max +22 dBm constant RF output vs.
64 * RX sensitivity: down to -139 dBm.
65 * Excellent blocking immunity
66
67 (% style="color:#037691" %)**Battery:**
68
69 * Li/SOCI2 un-chargeable battery
70 * Capacity: 8500mAh
71 * Self-Discharge: <1% / Year @ 25°C
72 * Max continuously current: 130mA
73 * Max boost current: 2A, 1 second
74
75 (% style="color:#037691" %)**Power Consumption**
76
77 * Sleep Mode: 5uA @ 3.3v
78 * LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm
79
80 == 1.4 Sleep mode and working mode ==
81
82
83 (% style="color:blue" %)**Deep Sleep Mode: **(%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.
84
85 (% style="color:blue" %)**Working Mode:** (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.
86
87
88 == 1.5 Button & LEDs ==
89
90
91 [[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675071855856-879.png]]
92
93
94 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
95 |=(% style="width: 167px;background-color:#D9E2F3;color:#0070C0" %)**Behavior on ACT**|=(% style="width: 117px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 225px;background-color:#D9E2F3;color:#0070C0" %)**Action**
96 |(% style="width:167px" %)Pressing ACT between 1s < time < 3s|(% style="width:117px" %)Send an uplink|(% style="width:225px" %)(((
97 If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, (% style="color:blue" %)**blue led** (%%)will blink once.
98 Meanwhile, BLE module will be active and user can connect via BLE to configure device.
99 )))
100 |(% style="width:167px" %)Pressing ACT for more than 3s|(% style="width:117px" %)Active Device|(% style="width:225px" %)(((
101 (% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:#037691" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network.
102 (% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.
103 Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device join or not join LoRaWAN network.
104 )))
105 |(% style="width:167px" %)Fast press ACT 5 times.|(% style="width:117px" %)Deactivate Device|(% style="width:225px" %)(% style="color:red" %)**Red led**(%%) will solid on for 5 seconds. Means device is in Deep Sleep Mode.
106
107 == 1.6 BLE connection ==
108
109
110 SN50v3-LB supports BLE remote configure.
111
112
113 BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:
114
115 * Press button to send an uplink
116 * Press button to active device.
117 * Device Power on or reset.
118
119 If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.
120
121
122 == 1.7 Pin Definitions ==
123
124
125 [[image:image-20230610163213-1.png||height="404" width="699"]]
126
127
128 == 1.8 Mechanical ==
129
130
131 [[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143884058-338.png]]
132
133 [[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143899218-599.png]]
134
135 [[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143909447-639.png]]
136
137
138 == 1.9 Hole Option ==
139
140
141 SN50v3-LB has different hole size options for different size sensor cable. The options provided are M12, M16 and M20. The definition is as below:
142
143 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220627104757-1.png?rev=1.1||alt="image-20220627104757-1.png"]]
144
145 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656298089706-973.png?rev=1.1||alt="1656298089706-973.png"]]
146
147
148 = 2. Configure SN50v3-LB to connect to LoRaWAN network =
149
150 == 2.1 How it works ==
151
152
153 The SN50v3-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the SN50v3-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
154
155
156 == 2.2 ​Quick guide to connect to LoRaWAN server (OTAA) ==
157
158
159 Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.
160
161 The LPS8v2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
162
163
164 (% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from SN50v3-LB.
165
166 Each SN50v3-LB is shipped with a sticker with the default device EUI as below:
167
168 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/S31-LB_S31B-LB/WebHome/image-20230426084152-1.png?width=502&height=233&rev=1.1||alt="图片-20230426084152-1.png" height="233" width="502"]]
169
170
171 You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
172
173
174 (% style="color:blue" %)**Register the device**
175
176 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/1654935135620-998.png?rev=1.1||alt="1654935135620-998.png"]]
177
178
179 (% style="color:blue" %)**Add APP EUI and DEV EUI**
180
181 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-4.png?width=753&height=551&rev=1.1||alt="图片-20220611161308-4.png"]]
182
183
184 (% style="color:blue" %)**Add APP EUI in the application**
185
186
187 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-5.png?width=742&height=601&rev=1.1||alt="图片-20220611161308-5.png"]]
188
189
190 (% style="color:blue" %)**Add APP KEY**
191
192 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-6.png?width=744&height=485&rev=1.1||alt="图片-20220611161308-6.png"]]
193
194
195 (% style="color:blue" %)**Step 2:**(%%) Activate SN50v3-LB
196
197
198 Press the button for 5 seconds to activate the SN50v3-LB.
199
200 (% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:blue" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.
201
202 After join success, it will start to upload messages to TTN and you can see the messages in the panel.
203
204
205 == 2.3 ​Uplink Payload ==
206
207 === 2.3.1 Device Status, FPORT~=5 ===
208
209
210 Users can use the downlink command(**0x26 01**) to ask SN50v3-LB to send device configure detail, include device configure status. SN50v3-LB will uplink a payload via FPort=5 to server.
211
212 The Payload format is as below.
213
214
215 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
216 |(% colspan="6" style="background-color:#d9e2f3; color:#0070c0" %)**Device Status (FPORT=5)**
217 |(% style="width:103px" %)**Size (bytes)**|(% style="width:72px" %)**1**|**2**|(% style="width:91px" %)**1**|(% style="width:86px" %)**1**|(% style="width:44px" %)**2**
218 |(% style="width:103px" %)Value|(% style="width:72px" %)Sensor Model|Firmware Version|(% style="width:91px" %)Frequency Band|(% style="width:86px" %)Sub-band|(% style="width:44px" %)BAT
219
220 Example parse in TTNv3
221
222
223 (% style="color:#037691" %)**Sensor Model**(%%): For SN50v3-LB, this value is 0x1C
224
225 (% style="color:#037691" %)**Firmware Version**(%%): 0x0100, Means: v1.0.0 version
226
227 (% style="color:#037691" %)**Frequency Band**:
228
229 0x01: EU868
230
231 0x02: US915
232
233 0x03: IN865
234
235 0x04: AU915
236
237 0x05: KZ865
238
239 0x06: RU864
240
241 0x07: AS923
242
243 0x08: AS923-1
244
245 0x09: AS923-2
246
247 0x0a: AS923-3
248
249 0x0b: CN470
250
251 0x0c: EU433
252
253 0x0d: KR920
254
255 0x0e: MA869
256
257
258 (% style="color:#037691" %)**Sub-Band**:
259
260 AU915 and US915:value 0x00 ~~ 0x08
261
262 CN470: value 0x0B ~~ 0x0C
263
264 Other Bands: Always 0x00
265
266
267 (% style="color:#037691" %)**Battery Info**:
268
269 Check the battery voltage.
270
271 Ex1: 0x0B45 = 2885mV
272
273 Ex2: 0x0B49 = 2889mV
274
275
276 === 2.3.2 Working Modes & Sensor Data. Uplink via FPORT~=2 ===
277
278
279 SN50v3-LB has different working mode for the connections of different type of sensors. This section describes these modes. Use can use the AT Command (% style="color:blue" %)**AT+MOD**(%%) to set SN50v3-LB to different working modes.
280
281 For example:
282
283 (% style="color:blue" %)**AT+MOD=2  ** (%%) ~/~/ will set the SN50v3 to work in MOD=2 distance mode which target to measure distance via Ultrasonic Sensor.
284
285
286 (% style="color:red" %) **Important Notice:**
287
288 ~1. Some working modes has payload more than 12 bytes, The US915/AU915/AS923 frequency bands' definition has maximum 11 bytes in (% style="color:blue" %)**DR0**(%%). Server sides will see NULL payload while SN50v3-LB transmit in DR0 with 12 bytes payload.
289
290 2. All modes share the same Payload Explanation from HERE.
291
292 3. By default, the device will send an uplink message every 20 minutes.
293
294
295 ==== 2.3.2.1  MOD~=1 (Default Mode) ====
296
297
298 In this mode, uplink payload includes in total 11 bytes. Uplink packets use FPORT=2.
299
300 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:520px" %)
301 |(% style="background-color:#d9e2f3; color:#0070c0; width:50px" %)**Size(bytes)**|(% style="background-color:#d9e2f3; color:#0070c0; width:20px" %)**2**|(% style="background-color:#d9e2f3; color:#0070c0; width:100px" %)**2**|(% style="background-color:#d9e2f3; color:#0070c0; width:50px" %)**2**|(% style="background-color:#d9e2f3; color:#0070c0; width:90px" %)**1**|(% style="background-color:#d9e2f3; color:#0070c0; width:130px" %)**2**|(% style="background-color:#d9e2f3; color:#0070c0; width:80px" %)**2**
302 |Value|Bat|(% style="width:191px" %)(((
303 Temperature(DS18B20)(PC13)
304 )))|(% style="width:78px" %)(((
305 ADC(PA4)
306 )))|(% style="width:216px" %)(((
307 Digital in(PB15)&Digital Interrupt(PA8)
308 )))|(% style="width:308px" %)(((
309 Temperature(SHT20 or SHT31 or BH1750 Illumination Sensor)
310 )))|(% style="width:154px" %)(((
311 Humidity(SHT20 or SHT31)
312 )))
313
314 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220627150949-6.png?rev=1.1||alt="image-20220627150949-6.png"]]
315
316
317 ==== 2.3.2.2  MOD~=2 (Distance Mode) ====
318
319
320 This mode is target to measure the distance. The payload of this mode is totally 11 bytes. The 8^^th^^ and 9^^th^^ bytes is for the distance.
321
322 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:520px" %)
323 |(% style="background-color:#d9e2f3; color:#0070c0; width:50px" %)**Size(bytes)**|(% style="background-color:#d9e2f3; color:#0070c0; width:30px" %)**2**|(% style="background-color:#d9e2f3; color:#0070c0; width:110px" %)**2**|(% style="background-color:#d9e2f3; color:#0070c0; width:40px" %)**2**|(% style="background-color:#d9e2f3; color:#0070c0; width:110px" %)**1**|(% style="background-color:#d9e2f3; color:#0070c0; width:140px" %)**2**|(% style="background-color:#d9e2f3; color:#0070c0; width:40px" %)**2**
324 |Value|BAT|(% style="width:196px" %)(((
325 Temperature(DS18B20)(PC13)
326 )))|(% style="width:87px" %)(((
327 ADC(PA4)
328 )))|(% style="width:189px" %)(((
329 Digital in(PB15) & Digital Interrupt(PA8)
330 )))|(% style="width:208px" %)(((
331 Distance measure by: 1) LIDAR-Lite V3HP
332 Or 2) Ultrasonic Sensor
333 )))|(% style="width:117px" %)Reserved
334
335 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656324539647-568.png?rev=1.1||alt="1656324539647-568.png"]]
336
337
338 (% style="color:blue" %)**Connection of LIDAR-Lite V3HP:**
339
340 [[image:image-20230512173758-5.png||height="563" width="712"]]
341
342
343 (% style="color:blue" %)**Connection to Ultrasonic Sensor:**
344
345 (% style="color:red" %)**Need to remove R1 and R2 resistors to get low power,otherwise there will be 240uA standby current.**
346
347 [[image:image-20230512173903-6.png||height="596" width="715"]]
348
349
350 For the connection to TF-Mini or TF-Luna , MOD2 payload is as below:
351
352 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:520px" %)
353 |(% style="background-color:#d9e2f3; color:#0070c0; width:50px" %)**Size(bytes)**|(% style="background-color:#d9e2f3; color:#0070c0; width:20px" %)**2**|(% style="background-color:#d9e2f3; color:#0070c0; width:100px" %)**2**|(% style="background-color:#d9e2f3; color:#0070c0; width:100px" %)**1**|(% style="background-color:#d9e2f3; color:#0070c0; width:50px" %)**2**|(% style="background-color:#d9e2f3; color:#0070c0; width:120px" %)**2**|(% style="background-color:#d9e2f3; color:#0070c0; width:80px" %)**2**
354 |Value|BAT|(% style="width:183px" %)(((
355 Temperature(DS18B20)(PC13)
356 )))|(% style="width:173px" %)(((
357 Digital in(PB15) & Digital Interrupt(PA8)
358 )))|(% style="width:84px" %)(((
359 ADC(PA4)
360 )))|(% style="width:323px" %)(((
361 Distance measure by:1)TF-Mini plus LiDAR
362 Or 2) TF-Luna LiDAR
363 )))|(% style="width:188px" %)Distance signal  strength
364
365 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656376779088-686.png?rev=1.1||alt="1656376779088-686.png"]]
366
367
368 **Connection to [[TF-Mini plus>>url:http://en.benewake.com/product/detail/5c345cd0e5b3a844c472329b.html]] LiDAR(UART version):**
369
370 (% style="color:red" %)**Need to remove R3 and R4 resistors to get low power,otherwise there will be 400uA standby current.**
371
372 [[image:image-20230512180609-7.png||height="555" width="802"]]
373
374
375 **Connection to [[TF-Luna>>url:http://en.benewake.com/product/detail/5e1c1fd04d839408076b6255.html]] LiDAR (UART version):**
376
377 (% style="color:red" %)**Need to remove R3 and R4 resistors to get low power,otherwise there will be 400uA standby current.**
378
379 [[image:image-20230610170047-1.png||height="452" width="799"]]
380
381
382 ==== 2.3.2.3  MOD~=3 (3 ADC + I2C) ====
383
384
385 This mode has total 12 bytes. Include 3 x ADC + 1x I2C
386
387 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:520px" %)
388 |=(% style="width: 50px;background-color:#D9E2F3;color:#0070C0" %)(((
389 **Size(bytes)**
390 )))|=(% style="width: 50px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 50px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 50px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 90px;background-color:#D9E2F3;color:#0070C0" %)**1**|=(% style="width: 110px;background-color:#D9E2F3;color:#0070C0" %)2|=(% style="width: 100px;background-color:#D9E2F3;color:#0070C0" %)2|=(% style="width: 20px;background-color:#D9E2F3;color:#0070C0" %)1
391 |Value|(% style="width:68px" %)(((
392 ADC1(PA4)
393 )))|(% style="width:75px" %)(((
394 ADC2(PA5)
395 )))|(((
396 ADC3(PA8)
397 )))|(((
398 Digital Interrupt(PB15)
399 )))|(% style="width:304px" %)(((
400 Temperature(SHT20 or SHT31 or BH1750 Illumination Sensor)
401 )))|(% style="width:163px" %)(((
402 Humidity(SHT20 or SHT31)
403 )))|(% style="width:53px" %)Bat
404
405 [[image:image-20230513110214-6.png]]
406
407
408 ==== 2.3.2.4 MOD~=4 (3 x DS18B20) ====
409
410
411 This mode has total 11 bytes. As shown below:
412
413 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:520px" %)
414 |(% style="background-color:#d9e2f3; color:#0070c0; width:50px" %)**Size(bytes)**|(% style="background-color:#d9e2f3; color:#0070c0; width:20px" %)**2**|(% style="background-color:#d9e2f3; color:#0070c0; width:100px" %)**2**|(% style="background-color:#d9e2f3; color:#0070c0; width:50px" %)**2**|(% style="background-color:#d9e2f3; color:#0070c0; width:100px" %)**1**|(% style="background-color:#d9e2f3; color:#0070c0; width:100px" %)**2**|(% style="background-color:#d9e2f3; color:#0070c0; width:100px" %)**2**
415 |Value|BAT|(% style="width:186px" %)(((
416 Temperature1(DS18B20)(PC13)
417 )))|(% style="width:82px" %)(((
418 ADC(PA4)
419 )))|(% style="width:210px" %)(((
420 Digital in(PB15) & Digital Interrupt(PA8) 
421 )))|(% style="width:191px" %)Temperature2(DS18B20)
422 (PB9)|(% style="width:183px" %)Temperature3(DS18B20)(PB8)
423
424 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656377606181-607.png?rev=1.1||alt="1656377606181-607.png"]]
425
426
427 [[image:image-20230513134006-1.png||height="559" width="736"]]
428
429
430 ==== 2.3.2.5  MOD~=5(Weight Measurement by HX711) ====
431
432
433 [[image:image-20230512164658-2.png||height="532" width="729"]]
434
435 Each HX711 need to be calibrated before used. User need to do below two steps:
436
437 1. Zero calibration. Don't put anything on load cell and run (% style="color:blue" %)**AT+WEIGRE**(%%) to calibrate to Zero gram.
438 1. Adjust calibration factor (default value 400): Put a known weight thing on load cell and run (% style="color:blue" %)**AT+WEIGAP**(%%) to adjust the Calibration Factor.
439 1. (((
440 Weight has 4 bytes, the unit is g.
441
442
443
444 )))
445
446 For example:
447
448 (% style="color:blue" %)**AT+GETSENSORVALUE =0**
449
450 Response:  Weight is 401 g
451
452 Check the response of this command and adjust the value to match the real value for thing.
453
454 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:520px" %)
455 |=(% style="width: 50px;background-color:#D9E2F3;color:#0070C0" %)(((
456 **Size(bytes)**
457 )))|=(% style="width: 20px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 150px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 50px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 200px;background-color:#D9E2F3;color:#0070C0" %)**1**|=(% style="width: 50px;background-color:#D9E2F3;color:#0070C0" %)**4**
458 |Value|BAT|(% style="width:193px" %)(((
459 Temperature(DS18B20)(PC13)
460 )))|(% style="width:85px" %)(((
461 ADC(PA4)
462 )))|(% style="width:186px" %)(((
463 Digital in(PB15) & Digital Interrupt(PA8)
464 )))|(% style="width:100px" %)Weight
465
466 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220820120036-2.png?width=1003&height=469&rev=1.1||alt="image-20220820120036-2.png" height="469" width="1003"]]
467
468
469 ==== 2.3.2.6  MOD~=6 (Counting Mode) ====
470
471
472 In this mode, the device will work in counting mode. It counts the interrupt on the interrupt pins and sends the count on TDC time.
473
474 Connection is as below. The PIR sensor is a count sensor, it will generate interrupt when people come close or go away. User can replace the PIR sensor with other counting sensors.
475
476 [[image:image-20230512181814-9.png||height="543" width="697"]]
477
478
479 (% style="color:red" %)**Note:** **LoRaWAN wireless transmission will infect the PIR sensor. Which cause the counting value increase +1 for every uplink. User can change PIR sensor or put sensor away of the SN50_v3 to avoid this happen.**
480
481 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:520px" %)
482 |=(% style="width: 60px;background-color:#D9E2F3;color:#0070C0" %)**Size(bytes)**|=(% style="width: 40px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 180px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 60px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 100px;background-color:#D9E2F3;color:#0070C0" %)**1**|=(% style="width: 80px;background-color:#D9E2F3;color:#0070C0" %)**4**
483 |Value|BAT|(% style="width:256px" %)(((
484 Temperature(DS18B20)(PC13)
485 )))|(% style="width:108px" %)(((
486 ADC(PA4)
487 )))|(% style="width:126px" %)(((
488 Digital in(PB15)
489 )))|(% style="width:145px" %)(((
490 Count(PA8)
491 )))
492
493 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656378441509-171.png?rev=1.1||alt="1656378441509-171.png"]]
494
495
496 ==== 2.3.2.7  MOD~=7 (Three interrupt contact modes) ====
497
498
499 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:520px" %)
500 |=(% style="width: 50px;background-color:#D9E2F3;color:#0070C0" %)(((
501 **Size(bytes)**
502 )))|=(% style="width: 20px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 90px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 50px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 90px;background-color:#D9E2F3;color:#0070C0" %)**1**|=(% style="width: 90px;background-color:#D9E2F3;color:#0070C0" %)**1**|=(% style="width: 90px;background-color:#D9E2F3;color:#0070C0" %)1|=(% style="width: 40px;background-color:#D9E2F3;color:#0070C0" %)2
503 |Value|BAT|(% style="width:188px" %)(((
504 Temperature(DS18B20)
505 (PC13)
506 )))|(% style="width:83px" %)(((
507 ADC(PA5)
508 )))|(% style="width:184px" %)(((
509 Digital Interrupt1(PA8)
510 )))|(% style="width:186px" %)Digital Interrupt2(PA4)|(% style="width:197px" %)Digital Interrupt3(PB15)|(% style="width:100px" %)Reserved
511
512 [[image:image-20230513111203-7.png||height="324" width="975"]]
513
514
515 ==== 2.3.2.8  MOD~=8 （3ADC+1DS18B20） ====
516
517
518 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:520px" %)
519 |=(% style="width: 50px;background-color:#D9E2F3;color:#0070C0" %)(((
520 **Size(bytes)**
521 )))|=(% style="width: 30px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 110px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 70px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 120px;background-color:#D9E2F3;color:#0070C0" %)**1**|=(% style="width: 70px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 70px;background-color:#D9E2F3;color:#0070C0" %)2
522 |Value|BAT|(% style="width:207px" %)(((
523 Temperature(DS18B20)
524 (PC13)
525 )))|(% style="width:94px" %)(((
526 ADC1(PA4)
527 )))|(% style="width:198px" %)(((
528 Digital Interrupt(PB15)
529 )))|(% style="width:84px" %)(((
530 ADC2(PA5)
531 )))|(% style="width:82px" %)(((
532 ADC3(PA8)
533 )))
534
535 [[image:image-20230513111231-8.png||height="335" width="900"]]
536
537
538 ==== 2.3.2.9  MOD~=9 (3DS18B20+ two Interrupt count mode) ====
539
540
541 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:520px" %)
542 |=(% style="width: 50px;background-color:#D9E2F3;color:#0070C0" %)(((
543 **Size(bytes)**
544 )))|=(% style="width: 20px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 90px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 90px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 60px;background-color:#D9E2F3;color:#0070C0" %)**1**|=(% style="width: 90px;background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 60px;background-color:#D9E2F3;color:#0070C0" %)4|=(% style="width: 60px;background-color:#D9E2F3;color:#0070C0" %)4
545 |Value|BAT|(((
546 Temperature
547 (DS18B20)(PC13)
548 )))|(((
549 Temperature2
550 (DS18B20)(PB9)
551 )))|(((
552 Digital Interrupt
553 (PB15)
554 )))|(% style="width:193px" %)(((
555 Temperature3
556 (DS18B20)(PB8)
557 )))|(% style="width:78px" %)(((
558 Count1(PA8)
559 )))|(% style="width:78px" %)(((
560 Count2(PA4)
561 )))
562
563 [[image:image-20230513111255-9.png||height="341" width="899"]]
564
565 (% style="color:blue" %)**The newly added AT command is issued correspondingly:**
566
567 (% style="color:#037691" %)** AT+INTMOD1 PA8**(%%)  pin：  Corresponding downlink:  (% style="color:#037691" %)**06 00 00 xx**
568
569 (% style="color:#037691" %)** AT+INTMOD2 PA4**(%%)  pin：  Corresponding downlink: (% style="color:#037691" %)**06 00 01 xx**
570
571 (% style="color:#037691" %)** AT+INTMOD3 PB15**(%%)  pin：  Corresponding downlink:  (% style="color:#037691" %)** 06 00 02 xx**
572
573
574 (% style="color:blue" %)**AT+SETCNT=aa,bb** 
575
576 When AA is 1, set the count of PA8 pin to BB Corresponding downlink：09 01 bb bb bb bb
577
578 When AA is 2, set the count of PA4 pin to BB Corresponding downlink：09 02 bb bb bb bb
579
580
581 ==== 2.3.2.10  MOD~=10 (PWM input capture and output mode，Since firmware v1.2) ====
582
583 (% style="color:red" %)**Note: Firmware not release, contact Dragino for testing.**
584
585 In this mode, the uplink can perform PWM input capture, and the downlink can perform PWM output.
586
587 [[It should be noted when using PWM mode.>>||anchor="H2.3.3.12A0PWMMOD"]]
588
589
590 ===== 2.3.2.10.a  Uplink, PWM input capture =====
591
592
593 [[image:image-20230817172209-2.png||height="439" width="683"]]
594
595 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:690px" %)
596 |(% style="background-color:#d9e2f3; color:#0070c0; width:50px" %)**Size(bytes)**|(% style="background-color:#d9e2f3; color:#0070c0; width:20px" %)**2**|(% style="background-color:#d9e2f3; color:#0070c0; width:100px" %)**2**|(% style="background-color:#d9e2f3; color:#0070c0; width:50px" %)**2**|(% style="background-color:#d9e2f3; color:#0070c0; width:135px" %)**1**|(% style="background-color:#d9e2f3; color:#0070c0; width:70px" %)**2**|(% style="background-color:#d9e2f3; color:#0070c0; width:89px" %)**2**
597 |Value|Bat|(% style="width:191px" %)(((
598 Temperature(DS18B20)(PC13)
599 )))|(% style="width:78px" %)(((
600 ADC(PA4)
601 )))|(% style="width:135px" %)(((
602 PWM_Setting
603
604 &Digital Interrupt(PA8)
605 )))|(% style="width:70px" %)(((
606 Pulse period
607 )))|(% style="width:89px" %)(((
608 Duration of high level
609 )))
610
611 [[image:image-20230817170702-1.png||height="161" width="1044"]]
612
613
614 When the device detects the following PWM signal ,decoder will converts the pulse period and high-level duration to frequency and duty cycle.
615
616 **Frequency：**
617
618 (% class="MsoNormal" %)
619 (% lang="EN-US" %)If (% style="background-attachment:initial; background-clip:initial; background-image:initial; background-origin:initial; background-position:initial; background-repeat:initial; background-size:initial; color:blue; font-family:Arial,sans-serif" %)**AT+PWMSET**(%%)**=0, **(% lang="EN-US" %)Frequency= 1000000/(%%)Pulse period（HZ）;
620
621 (% class="MsoNormal" %)
622 (% lang="EN-US" %)If (% style="background-attachment:initial; background-clip:initial; background-image:initial; background-origin:initial; background-position:initial; background-repeat:initial; background-size:initial; color:blue; font-family:Arial,sans-serif" %)**AT+PWMSET**(%%)**=1, **(% lang="EN-US" %)Frequency= 1000/(%%)Pulse period（HZ）;
623
624
625 (% class="MsoNormal" %)
626 **Duty cycle:**
627
628 Duty cycle= Duration of high level/ Pulse period*100 ~(%).
629
630 [[image:image-20230818092200-1.png||height="344" width="627"]]
631
632 ===== 2.3.2.10.b  Uplink, PWM output =====
633
634 [[image:image-20230817172209-2.png||height="439" width="683"]]
635
636
637
638
639
640
641 ===== 2.3.2.10.c  Downlink, PWM output =====
642
643
644 [[image:image-20230817173800-3.png||height="412" width="685"]]
645
646 Downlink:  (% style="color:#037691" %)**0B xx xx xx yy zz zz**
647
648 xx xx xx is the output frequency, the unit is HZ.
649
650 yy is the duty cycle of the output, the unit is %.
651
652 zz zz is the time delay of the output, the unit is ms.
653
654
655 For example, send a downlink command: 0B 00 61 A8 32 13 88, the frequency is 25KHZ, the duty cycle is 50, and the output time is 5 seconds.
656
657 The oscilloscope displays as follows:
658
659 [[image:image-20230817173858-5.png||height="694" width="921"]]
660
661
662 === 2.3.3  ​Decode payload ===
663
664
665 While using TTN V3 network, you can add the payload format to decode the payload.
666
667 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656378466788-734.png?rev=1.1||alt="1656378466788-734.png"]]
668
669 The payload decoder function for TTN V3 are here:
670
671 SN50v3-LB TTN V3 Payload Decoder:  [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>url:https://github.com/dragino/dragino-end-node-decoder]]
672
673
674 ==== 2.3.3.1 Battery Info ====
675
676
677 Check the battery voltage for SN50v3-LB.
678
679 Ex1: 0x0B45 = 2885mV
680
681 Ex2: 0x0B49 = 2889mV
682
683
684 ==== 2.3.3.2  Temperature (DS18B20) ====
685
686
687 If there is a DS18B20 connected to PC13 pin. The temperature will be uploaded in the payload.
688
689 More DS18B20 can check the [[3 DS18B20 mode>>||anchor="H2.3.2.4MOD3D4283xDS18B2029"]]
690
691 (% style="color:blue" %)**Connection:**
692
693 [[image:image-20230512180718-8.png||height="538" width="647"]]
694
695
696 (% style="color:blue" %)**Example**:
697
698 If payload is: 0105H:  (0105 & 8000 == 0), temp = 0105H /10 = 26.1 degree
699
700 If payload is: FF3FH :  (FF3F & 8000 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.
701
702 （FF3F & 8000：Judge whether the highest bit is 1, when the highest bit is 1, it is negative）
703
704
705 ==== 2.3.3.3 Digital Input ====
706
707
708 The digital input for pin PB15,
709
710 * When PB15 is high, the bit 1 of payload byte 6 is 1.
711 * When PB15 is low, the bit 1 of payload byte 6 is 0.
712
713 (% class="wikigeneratedid" id="H2.3.3.4A0AnalogueDigitalConverter28ADC29" %)
714 (((
715 When the digital interrupt pin is set to AT+INTMODx=0, this pin is used as a digital input pin.
716
717 (% style="color:red" %)**Note: The maximum voltage input supports 3.6V.**
718
719
720 )))
721
722 ==== 2.3.3.4  Analogue Digital Converter (ADC) ====
723
724
725 The measuring range of the ADC is only about 0.1V to 1.1V The voltage resolution is about 0.24mv.
726
727 When the measured output voltage of the sensor is not within the range of 0.1V and 1.1V, the output voltage terminal of the sensor shall be divided The example in the following figure is to reduce the output voltage of the sensor by three times If it is necessary to reduce more times, calculate according to the formula in the figure and connect the corresponding resistance in series.
728
729 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220628150112-1.png?width=285&height=241&rev=1.1||alt="image-20220628150112-1.png" height="241" width="285"]]
730
731
732 (% style="color:red" %)**Note: If the ADC type sensor needs to be powered by SN50_v3, it is recommended to use +5V to control its switch.Only sensors with low power consumption can be powered with VDD.**
733
734
735 The position of PA5 on the hardware after **LSN50 v3.3** is changed to the position shown in the figure below, and the collected voltage becomes one-sixth of the original.
736
737 [[image:image-20230811113449-1.png||height="370" width="608"]]
738
739 ==== 2.3.3.5 Digital Interrupt ====
740
741
742 Digital Interrupt refers to pin PA8, and there are different trigger methods. When there is a trigger, the SN50v3-LB will send a packet to the server.
743
744 (% style="color:blue" %)** Interrupt connection method:**
745
746 [[image:image-20230513105351-5.png||height="147" width="485"]]
747
748
749 (% style="color:blue" %)**Example to use with door sensor :**
750
751 The door sensor is shown at right. It is a two wire magnetic contact switch used for detecting the open/close status of doors or windows.
752
753 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379210849-860.png?rev=1.1||alt="1656379210849-860.png"]]
754
755 When the two pieces are close to each other, the 2 wire output will be short or open (depending on the type), while if the two pieces are away from each other, the 2 wire output will be the opposite status. So we can use SN50v3-LB interrupt interface to detect the status for the door or window.
756
757
758 (% style="color:blue" %)**Below is the installation example:**
759
760 Fix one piece of the magnetic sensor to the door and connect the two pins to SN50v3-LB as follows:
761
762 * (((
763 One pin to SN50v3-LB's PA8 pin
764 )))
765 * (((
766 The other pin to SN50v3-LB's VDD pin
767 )))
768
769 Install the other piece to the door. Find a place where the two pieces will be close to each other when the door is closed. For this particular magnetic sensor, when the door is closed, the output will be short, and PA8 will be at the VCC voltage.
770
771 Door sensors have two types: (% style="color:blue" %)** NC (Normal close)**(%%) and (% style="color:blue" %)**NO (normal open)**(%%). The connection for both type sensors are the same. But the decoding for payload are reverse, user need to modify this in the IoT Server decoder.
772
773 When door sensor is shorted, there will extra power consumption in the circuit, the extra current is 3v3/R14 = 3v3/1Mohm = 3uA which can be ignored.
774
775 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379283019-229.png?rev=1.1||alt="1656379283019-229.png"]]
776
777 The above photos shows the two parts of the magnetic switch fitted to a door.
778
779 The software by default uses the falling edge on the signal line as an interrupt. We need to modify it to accept both the rising edge (0v ~-~-> VCC , door close) and the falling edge (VCC ~-~-> 0v , door open) as the interrupt.
780
781 The command is:
782
783 (% style="color:blue" %)**AT+INTMOD1=1   ** (%%) ~/~/  (more info about INMOD please refer** **[[**AT Command Manual**>>url:http://www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/&file=DRAGINO_LSN50_AT_Commands_v1.5.1.pdf]]**. **)
784
785 Below shows some screen captures in TTN V3:
786
787 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379339508-835.png?rev=1.1||alt="1656379339508-835.png"]]
788
789
790 In **MOD=1**, user can use byte 6 to see the status for door open or close. TTN V3 decoder is as below:
791
792 door= (bytes[6] & 0x80)? "CLOSE":"OPEN";
793
794
795 ==== 2.3.3.6 I2C Interface (SHT20 & SHT31) ====
796
797
798 The SDA and SCK are I2C interface lines. You can use these to connect to an I2C device and get the sensor data.
799
800 We have made an example to show how to use the I2C interface to connect to the SHT20/ SHT31 Temperature and Humidity Sensor.
801
802 (% style="color:red" %)**Notice: Different I2C sensors have different I2C commands set and initiate process, if user want to use other I2C sensors, User need to re-write the source code to support those sensors. SHT20/ SHT31 code in SN50v3-LB will be a good reference.**
803
804
805 Below is the connection to SHT20/ SHT31. The connection is as below:
806
807 [[image:image-20230610170152-2.png||height="501" width="846"]]
808
809
810 The device will be able to get the I2C sensor data now and upload to IoT Server.
811
812 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379664142-345.png?rev=1.1||alt="1656379664142-345.png"]]
813
814 Convert the read byte to decimal and divide it by ten.
815
816 **Example:**
817
818 Temperature:  Read:0116(H) = 278(D)  Value:  278 /10=27.8℃;
819
820 Humidity:    Read:0248(H)=584(D)  Value:  584 / 10=58.4, So 58.4%
821
822 If you want to use other I2C device, please refer the SHT20 part source code as reference.
823
824
825 ==== 2.3.3.7  ​Distance Reading ====
826
827
828 Refer [[Ultrasonic Sensor section>>||anchor="H2.3.3.8UltrasonicSensor"]].
829
830
831 ==== 2.3.3.8 Ultrasonic Sensor ====
832
833
834 This Fundamental Principles of this sensor can be found at this link: [[https:~~/~~/wiki.dfrobot.com/Weather_-_proof_Ultrasonic_Sensor_with_Separate_Probe_SKU~~_~~__SEN0208>>url:https://wiki.dfrobot.com/Weather_-_proof_Ultrasonic_Sensor_with_Separate_Probe_SKU___SEN0208]]
835
836 The SN50v3-LB detects the pulse width of the sensor and converts it to mm output. The accuracy will be within 1 centimeter. The usable range (the distance between the ultrasonic probe and the measured object) is between 24cm and 600cm.
837
838 The working principle of this sensor is similar to the (% style="color:blue" %)**HC-SR04**(%%) ultrasonic sensor.
839
840 The picture below shows the connection:
841
842 [[image:image-20230512173903-6.png||height="596" width="715"]]
843
844
845 Connect to the SN50v3-LB and run (% style="color:blue" %)**AT+MOD=2**(%%) to switch to ultrasonic mode (ULT).
846
847 The ultrasonic sensor uses the 8^^th^^ and 9^^th^^ byte for the measurement value.
848
849 **Example:**
850
851 Distance:  Read: 0C2D(Hex) = 3117(D)  Value:  3117 mm=311.7 cm
852
853
854 ==== 2.3.3.9  Battery Output - BAT pin ====
855
856
857 The BAT pin of SN50v3-LB is connected to the Battery directly. If users want to use BAT pin to power an external sensor. User need to make sure the external sensor is of low power consumption. Because the BAT pin is always open. If the external sensor is of high power consumption. the battery of SN50v3-LB will run out very soon.
858
859
860 ==== 2.3.3.10  +5V Output ====
861
862
863 SN50v3-LB will enable +5V output before all sampling and disable the +5v after all sampling. 
864
865 The 5V output time can be controlled by AT Command.
866
867 (% style="color:blue" %)**AT+5VT=1000**
868
869 Means set 5V valid time to have 1000ms. So the real 5V output will actually have 1000ms + sampling time for other sensors.
870
871 By default the **AT+5VT=500**. If the external sensor which require 5v and require more time to get stable state, user can use this command to increase the power ON duration for this sensor.
872
873
874 ==== 2.3.3.11  BH1750 Illumination Sensor ====
875
876
877 MOD=1 support this sensor. The sensor value is in the 8^^th^^ and 9^^th^^ bytes.
878
879 [[image:image-20230512172447-4.png||height="416" width="712"]]
880
881
882 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220628110012-12.png?rev=1.1||alt="image-20220628110012-12.png" height="361" width="953"]]
883
884
885 ==== 2.3.3.12  PWM MOD ====
886
887
888 * (((
889 The maximum voltage that the SDA pin of SN50v3 can withstand is 3.6V, and it cannot exceed this voltage value, otherwise the chip may be burned.
890 )))
891 * (((
892 If the PWM pin connected to the SDA pin cannot maintain a high level when it is not working, you need to remove the resistor R2 or replace it with a resistor with a larger resistance, otherwise a sleep current of about 360uA will be generated. The position of the resistor is shown in the figure below:
893 )))
894
895 [[image:image-20230817183249-3.png||height="320" width="417"]]
896
897 * (((
898 The signal captured by the input should preferably be processed by hardware filtering and then connected in. The software processing method is to capture four values, discard the first captured value, and then take the middle value of the second, third, and fourth captured values.
899 )))
900 * (((
901 Since the device can only detect a pulse period of 50ms when [[AT+PWMSET=0>>||anchor="H3.3.8PWMsetting"]] (counting in microseconds), it is necessary to change the value of PWMSET according to the frequency of input capture.
902 )))
903 * (((
904 PWM Input allows low power consumption. PWM Output to achieve real-time control, you need to go to class C. Power consumption will not be low.
905
906 For PWM Output Feature, there are two consideration to see if the device can be powered by battery or have to be powered by external DC.
907
908 a) If real-time control output is required, the SN50v3-LB is already operating in class C and an external power supply must be used.
909
910 b) If the output duration is more than 30 seconds, better to use external power source. 
911
912
913
914 )))
915
916 ==== 2.3.3.13  Working MOD ====
917
918
919 The working MOD info is contained in the Digital in & Digital Interrupt byte (7^^th^^ Byte).
920
921 User can use the 3^^rd^^ ~~ 7^^th^^  bit of this byte to see the working mod:
922
923 Case 7^^th^^ Byte >> 2 & 0x1f:
924
925 * 0: MOD1
926 * 1: MOD2
927 * 2: MOD3
928 * 3: MOD4
929 * 4: MOD5
930 * 5: MOD6
931 * 6: MOD7
932 * 7: MOD8
933 * 8: MOD9
934 * 9: MOD10
935
936 == 2.4 Payload Decoder file ==
937
938
939 In TTN, use can add a custom payload so it shows friendly reading
940
941 In the page (% style="color:#037691" %)**Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder**(%%) to add the decoder from:
942
943 [[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/SN50_v3-LB>>https://github.com/dragino/dragino-end-node-decoder/tree/main/SN50_v3-LB]]
944
945
946 == 2.5 Frequency Plans ==
947
948
949 The SN50v3-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
950
951 [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]
952
953
954 = 3. Configure SN50v3-LB =
955
956 == 3.1 Configure Methods ==
957
958
959 SN50v3-LB supports below configure method:
960
961 * AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
962 * AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].
963 * LoRaWAN Downlink.  Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
964
965 == 3.2 General Commands ==
966
967
968 These commands are to configure:
969
970 * General system settings like: uplink interval.
971 * LoRaWAN protocol & radio related command.
972
973 They are same for all Dragino Devices which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:
974
975 [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
976
977
978 == 3.3 Commands special design for SN50v3-LB ==
979
980
981 These commands only valid for SN50v3-LB, as below:
982
983
984 === 3.3.1 Set Transmit Interval Time ===
985
986
987 Feature: Change LoRaWAN End Node Transmit Interval.
988
989 (% style="color:blue" %)**AT Command: AT+TDC**
990
991 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
992 |=(% style="width: 156px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 137px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="background-color:#D9E2F3;color:#0070C0" %)**Response**
993 |(% style="width:156px" %)AT+TDC=?|(% style="width:137px" %)Show current transmit Interval|(((
994 30000
995 OK
996 the interval is 30000ms = 30s
997 )))
998 |(% style="width:156px" %)AT+TDC=60000|(% style="width:137px" %)Set Transmit Interval|(((
999 OK
1000 Set transmit interval to 60000ms = 60 seconds
1001 )))
1002
1003 (% style="color:blue" %)**Downlink Command: 0x01**
1004
1005 Format: Command Code (0x01) followed by 3 bytes time value.
1006
1007 If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
1008
1009 * Example 1: Downlink Payload: 0100001E  ~/~/  Set Transmit Interval (TDC) = 30 seconds
1010 * Example 2: Downlink Payload: 0100003C  ~/~/  Set Transmit Interval (TDC) = 60 seconds
1011
1012 === 3.3.2 Get Device Status ===
1013
1014
1015 Send a LoRaWAN downlink to ask the device to send its status.
1016
1017 (% style="color:blue" %)**Downlink Payload: 0x26 01**
1018
1019 Sensor will upload Device Status via **FPORT=5**. See payload section for detail.
1020
1021
1022 === 3.3.3 Set Interrupt Mode ===
1023
1024
1025 Feature, Set Interrupt mode for GPIO_EXIT.
1026
1027 (% style="color:blue" %)**AT Command: AT+INTMOD1，AT+INTMOD2，AT+INTMOD3**
1028
1029 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
1030 |=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 197px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 158px;background-color:#D9E2F3;color:#0070C0" %)**Response**
1031 |(% style="width:154px" %)AT+INTMOD1=?|(% style="width:196px" %)Show current interrupt mode|(% style="width:157px" %)(((
1032 0
1033 OK
1034 the mode is 0 =Disable Interrupt
1035 )))
1036 |(% style="width:154px" %)AT+INTMOD1=2|(% style="width:196px" %)(((
1037 Set Transmit Interval
1038 0. (Disable Interrupt),
1039 ~1. (Trigger by rising and falling edge)
1040 2. (Trigger by falling edge)
1041 3. (Trigger by rising edge)
1042 )))|(% style="width:157px" %)OK
1043 |(% style="width:154px" %)AT+INTMOD2=3|(% style="width:196px" %)(((
1044 Set Transmit Interval
1045 trigger by rising edge.
1046 )))|(% style="width:157px" %)OK
1047 |(% style="width:154px" %)AT+INTMOD3=0|(% style="width:196px" %)Disable Interrupt|(% style="width:157px" %)OK
1048
1049 (% style="color:blue" %)**Downlink Command: 0x06**
1050
1051 Format: Command Code (0x06) followed by 3 bytes.
1052
1053 This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
1054
1055 * Example 1: Downlink Payload: 06000000  **~-~-->**  AT+INTMOD1=0
1056 * Example 2: Downlink Payload: 06000003  **~-~-->**  AT+INTMOD1=3
1057 * Example 3: Downlink Payload: 06000102  **~-~-->**  AT+INTMOD2=2
1058 * Example 4: Downlink Payload: 06000201  **~-~-->**  AT+INTMOD3=1
1059
1060 === 3.3.4 Set Power Output Duration ===
1061
1062
1063 Control the output duration 5V . Before each sampling, device will
1064
1065 ~1. first enable the power output to external sensor,
1066
1067 2. keep it on as per duration, read sensor value and construct uplink payload
1068
1069 3. final, close the power output.
1070
1071 (% style="color:blue" %)**AT Command: AT+5VT**
1072
1073 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
1074 |=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 197px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 158px;background-color:#D9E2F3;color:#0070C0" %)**Response**
1075 |(% style="width:154px" %)AT+5VT=?|(% style="width:196px" %)Show 5V open time.|(% style="width:157px" %)(((
1076 500(default)
1077 OK
1078 )))
1079 |(% style="width:154px" %)AT+5VT=1000|(% style="width:196px" %)(((
1080 Close after a delay of 1000 milliseconds.
1081 )))|(% style="width:157px" %)OK
1082
1083 (% style="color:blue" %)**Downlink Command: 0x07**
1084
1085 Format: Command Code (0x07) followed by 2 bytes.
1086
1087 The first and second bytes are the time to turn on.
1088
1089 * Example 1: Downlink Payload: 070000  **~-~-->**  AT+5VT=0
1090 * Example 2: Downlink Payload: 0701F4  **~-~-->**  AT+5VT=500
1091
1092 === 3.3.5 Set Weighing parameters ===
1093
1094
1095 Feature: Working mode 5 is effective, weight initialization and weight factor setting of HX711.
1096
1097 (% style="color:blue" %)**AT Command: AT+WEIGRE,AT+WEIGAP**
1098
1099 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
1100 |=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 197px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 158px;background-color:#D9E2F3;color:#0070C0" %)**Response**
1101 |(% style="width:154px" %)AT+WEIGRE|(% style="width:196px" %)Weight is initialized to 0.|(% style="width:157px" %)OK
1102 |(% style="width:154px" %)AT+WEIGAP=？|(% style="width:196px" %)400.0|(% style="width:157px" %)OK(default)
1103 |(% style="width:154px" %)AT+WEIGAP=400.3|(% style="width:196px" %)Set the factor to 400.3.|(% style="width:157px" %)OK
1104
1105 (% style="color:blue" %)**Downlink Command: 0x08**
1106
1107 Format: Command Code (0x08) followed by 2 bytes or 4 bytes.
1108
1109 Use AT+WEIGRE when the first byte is 1, only 1 byte. When it is 2, use AT+WEIGAP, there are 3 bytes.
1110
1111 The second and third bytes are multiplied by 10 times to be the AT+WEIGAP value.
1112
1113 * Example 1: Downlink Payload: 0801  **~-~-->**  AT+WEIGRE
1114 * Example 2: Downlink Payload: 08020FA3  **~-~-->**  AT+WEIGAP=400.3
1115 * Example 3: Downlink Payload: 08020FA0  **~-~-->**  AT+WEIGAP=400.0
1116
1117 === 3.3.6 Set Digital pulse count value ===
1118
1119
1120 Feature: Set the pulse count value.
1121
1122 Count 1 is PA8 pin of mode 6 and mode 9. Count 2 is PA4 pin of mode 9.
1123
1124 (% style="color:blue" %)**AT Command: AT+SETCNT**
1125
1126 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
1127 |=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 197px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 158px;background-color:#D9E2F3;color:#0070C0" %)**Response**
1128 |(% style="width:154px" %)AT+SETCNT=1,100|(% style="width:196px" %)Initialize the count value 1 to 100.|(% style="width:157px" %)OK
1129 |(% style="width:154px" %)AT+SETCNT=2,0|(% style="width:196px" %)Initialize the count value 2 to 0.|(% style="width:157px" %)OK
1130
1131 (% style="color:blue" %)**Downlink Command: 0x09**
1132
1133 Format: Command Code (0x09) followed by 5 bytes.
1134
1135 The first byte is to select which count value to initialize, and the next four bytes are the count value to be initialized.
1136
1137 * Example 1: Downlink Payload: 090100000000  **~-~-->**  AT+SETCNT=1,0
1138 * Example 2: Downlink Payload: 0902000003E8  **~-~-->**  AT+SETCNT=2,1000
1139
1140 === 3.3.7 Set Workmode ===
1141
1142
1143 Feature: Switch working mode.
1144
1145 (% style="color:blue" %)**AT Command: AT+MOD**
1146
1147 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
1148 |=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 197px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 158px;background-color:#D9E2F3;color:#0070C0" %)**Response**
1149 |(% style="width:154px" %)AT+MOD=?|(% style="width:196px" %)Get the current working mode.|(% style="width:157px" %)(((
1150 OK
1151 )))
1152 |(% style="width:154px" %)AT+MOD=4|(% style="width:196px" %)Set the working mode to 3DS18B20s.|(% style="width:157px" %)(((
1153 OK
1154 Attention:Take effect after ATZ
1155 )))
1156
1157 (% style="color:blue" %)**Downlink Command: 0x0A**
1158
1159 Format: Command Code (0x0A) followed by 1 bytes.
1160
1161 * Example 1: Downlink Payload: 0A01  **~-~-->**  AT+MOD=1
1162 * Example 2: Downlink Payload: 0A04  **~-~-->**  AT+MOD=4
1163
1164 (% id="H3.3.8PWMsetting" %)
1165 === 3.3.8 PWM setting ===
1166
1167
1168 (% class="mark" %)Feature: Set the time acquisition unit for PWM input capture.
1169
1170 (% style="color:blue" %)**AT Command: AT+PWMSET**
1171
1172 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
1173 |=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 223px; background-color: rgb(217, 226, 243); color: rgb(0, 112, 192);" %)**Function**|=(% style="width: 130px; background-color: rgb(217, 226, 243); color: rgb(0, 112, 192);" %)**Response**
1174 |(% style="width:154px" %)AT+PWMSET=?|(% style="width:223px" %)0|(% style="width:130px" %)(((
1175 0(default)
1176
1177 OK
1178 )))
1179 |(% style="width:154px" %)AT+PWMSET=0|(% style="width:223px" %)The unit of PWM capture time is microsecond. The capture frequency range is between 20HZ and 100000HZ.   |(% style="width:130px" %)(((
1180 OK
1181
1182 )))
1183 |(% style="width:154px" %)AT+PWMSET=1|(% style="width:223px" %)The unit of PWM capture time is millisecond.  The capture frequency range is between 5HZ and 250HZ. |(% style="width:130px" %)OK
1184
1185 (% style="color:blue" %)**Downlink Command: 0x0C**
1186
1187 Format: Command Code (0x0C) followed by 1 bytes.
1188
1189 * Example 1: Downlink Payload: 0C00  **~-~-->**  AT+PWMSET=0
1190 * Example 2: Downlink Payload: 0C01  **~-~-->**  AT+PWMSET=1
1191
1192
1193
1194 (% class="mark" %)Feature: Set the time acquisition unit for PWM output.
1195
1196 (% style="color:blue" %)**AT Command: AT+PWMOUT**
1197
1198 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
1199 |=(% style="width: 183px; background-color: rgb(217, 226, 243); color: rgb(0, 112, 192);" %)**Command Example**|=(% style="width: 193px; background-color: rgb(217, 226, 243); color: rgb(0, 112, 192);" %)**Function**|=(% style="width: 137px; background-color: rgb(217, 226, 243); color: rgb(0, 112, 192);" %)**Response**
1200 |(% style="width:183px" %)AT+PWMOUT=?|(% style="width:193px" %)0|(% style="width:137px" %)(((
1201 0,0,0(default)
1202
1203 OK
1204 )))
1205 |(% style="width:183px" %)AT+PWMOUT=0,0,0|(% style="width:193px" %)The default is PWM input detection|(% style="width:137px" %)(((
1206 OK
1207
1208 )))
1209 |(% style="width:183px" %)AT+PWMOUT=5,1000,50|(% style="width:193px" %)(((
1210 The PWM output time is 5ms, the output frequency is 1000HZ, and the output duty cycle is 50%.
1211
1212
1213 )))|(% style="width:137px" %)(((
1214 OK
1215 )))
1216
1217 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
1218 |=(% style="width: 155px; background-color: rgb(217, 226, 243); color: rgb(0, 112, 192);" %)**Command Example**|=(% style="width: 112px; background-color: rgb(217, 226, 243); color: rgb(0, 112, 192);" %)**Function**|=(% style="width: 242px; background-color: rgb(217, 226, 243); color: rgb(0, 112, 192);" %)**parameters**
1219 |(% colspan="1" rowspan="3" style="width:155px" %)(((
1220 AT+PWMOUT=a,b,c
1221
1222
1223 )))|(% colspan="1" rowspan="3" style="width:112px" %)(((
1224 Set PWM output time, output frequency and output duty cycle.(((
1225
1226 )))
1227
1228 (((
1229
1230 )))
1231 )))|(% style="width:242px" %)(((
1232 a: Output time (unit: seconds)
1233
1234 The value ranges from 0 to 65535.
1235
1236 When a=65535, PWM will always output.
1237 )))
1238 |(% style="width:242px" %)(((
1239 b: Output frequency (unit: HZ)
1240 )))
1241 |(% style="width:242px" %)(((
1242 c: Output duty cycle (unit: %)
1243
1244 The value ranges from 0 to 100.
1245 )))
1246
1247 (% style="color:blue" %)**Downlink Command: 0x0B01**
1248
1249 Format: Command Code (0x0B01) followed by 6 bytes.
1250
1251 Downlink payload：0B01 bb cc aa **~-~--> **AT+PWMOUT=a,b,c
1252
1253 * Example 1: Downlink Payload: 0B01 03E8 0032 0005 **~-~-->**  AT+PWMSET=5,1000,50
1254 * Example 2: Downlink Payload: 0B01 07D0 003C 000A **~-~-->**  AT+PWMSET=10,2000,60
1255
1256 = 4. Battery & Power Cons =
1257
1258
1259 SN50v3-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
1260
1261 [[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
1262
1263
1264 = 5. OTA Firmware update =
1265
1266
1267 (% class="wikigeneratedid" %)
1268 **User can change firmware SN50v3-LB to:**
1269
1270 * Change Frequency band/ region.
1271 * Update with new features.
1272 * Fix bugs.
1273
1274 **Firmware and changelog can be downloaded from :** **[[Firmware download link>>https://www.dropbox.com/sh/4rov7bcp6u28exp/AACt-wAySd4si5AXi8DBmvSca?dl=0]]**
1275
1276 **Methods to Update Firmware:**
1277
1278 * (Recommanded way) OTA firmware update via wireless: **[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]**
1279 * Update through UART TTL interface: **[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.
1280
1281 = 6. FAQ =
1282
1283 == 6.1 Where can i find source code of SN50v3-LB? ==
1284
1285
1286 * **[[Hardware Source Files>>https://github.com/dragino/Lora/tree/master/LSN50/v3.0]].**
1287 * **[[Software Source Code & Compile instruction>>https://github.com/dragino/SN50v3]].**
1288
1289 == 6.2 How to generate PWM Output in SN50v3-LB? ==
1290
1291
1292 See this document: **[[Generate PWM Output on SN50v3>>https://www.dropbox.com/scl/fi/r3trcet2knujg40w0mgyn/Generate-PWM-Output-on-SN50v3.pdf?rlkey=rxsgmrhhrv62iiiwjq9sv10bn&dl=0]]**.
1293
1294
1295 == 6.3 How to put several sensors to a SN50v3-LB? ==
1296
1297
1298 When we want to put several sensors to A SN50v3-LB, the waterproof at the grand connector will become an issue. User can try to exchange the grand connector to below type.
1299
1300 [[Reference Supplier>>https://www.yscableglands.com/cable-glands/nylon-cable-glands/cable-gland-rubber-seal.html]].
1301
1302 [[image:image-20230810121434-1.png||height="242" width="656"]]
1303
1304
1305 = 7. Order Info =
1306
1307
1308 Part Number: (% style="color:blue" %)**SN50v3-LB-XX-YY**
1309
1310 (% style="color:red" %)**XX**(%%): The default frequency band
1311
1312 * (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band
1313 * (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band
1314 * (% style="color:red" %)**EU433**(%%): LoRaWAN EU433 band
1315 * (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band
1316 * (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band
1317 * (% style="color:red" %)**US915**(%%): LoRaWAN US915 band
1318 * (% style="color:red" %)**IN865**(%%): LoRaWAN IN865 band
1319 * (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
1320
1321 (% style="color:red" %)**YY: ** (%%)Hole Option
1322
1323 * (% style="color:red" %)**12**(%%): With M12 waterproof cable hole
1324 * (% style="color:red" %)**16**(%%): With M16 waterproof cable hole
1325 * (% style="color:red" %)**20**(%%): With M20 waterproof cable hole
1326 * (% style="color:red" %)**NH**(%%): No Hole
1327
1328 = 8. ​Packing Info =
1329
1330
1331 (% style="color:#037691" %)**Package Includes**:
1332
1333 * SN50v3-LB LoRaWAN Generic Node
1334
1335 (% style="color:#037691" %)**Dimension and weight**:
1336
1337 * Device Size: cm
1338 * Device Weight: g
1339 * Package Size / pcs : cm
1340 * Weight / pcs : g
1341
1342 = 9. Support =
1343
1344
1345 * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
1346
1347 * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.cc>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.cc]]

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0