SN50v3-LB LoRaWAN Sensor Node User Manual

(% style="color:blue" %)**SN50V3-LB **(%%)LoRaWAN Sensor Node is a Long Range LoRa Sensor Node. It is designed for outdoor use and powered by (% style="color:blue" %)** 8500mA Li/SOCl2 battery**(%%) for long term use.SN50V3-LB is designed to facilitate developers to quickly deploy industrial level LoRa and IoT solutions. It help users to turn the idea into a practical application and make the Internet of Things a reality. It is easy to program, create and connect your things everywhere.

21

22

(% style="color:blue" %)**SN50V3-LB wireless part**(%%) is based on SX1262 allows the user to send data and reach extremely long ranges at low data-rates.It provides ultra-long range spread spectrum communication and high interference immunity whilst minimising current consumption.It targets professional wireless sensor network applications such as irrigation systems, smart metering, smart cities, smartphone detection, building automation, and so on.

23

24

(% style="color:blue" %)**SN50V3-LB **(%%)has a powerful 48Mhz ARM microcontroller with 256KB flash and 64KB RAM. It has multiplex I/O pins to connect to different sensors.

25

26

(% style="color:blue" %)**SN50V3-LB**(%%) has a built-in BLE module, user can configure the sensor remotely via Mobile Phone. It also support OTA upgrade via private LoRa protocol for easy maintaining.

27

28

SN50V3-LB is the 3^^rd^^ generation of LSN50 series generic sensor node from Dragino. It is an (% style="color:blue" %)**open source project**(%%) and has a mature LoRaWAN stack and application software. User can use the pre-load software for their IoT projects or easily customize the software for different requirements.

== 1.2 Features ==

* LoRaWAN 1.0.3 Class A

34

* Ultra-low power consumption

35

* Open-Source hardware/software

36

* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865

37

* Support Bluetooth v5.1 and LoRaWAN remote configure

38

* Support wireless OTA update firmware

39

* Uplink on periodically

40

* Downlink to change configure

41

* 8500mAh Battery for long term use

42

43

== 1.3 Specification ==

44

45

46

(% style="color:#037691" %)**Common DC Characteristics:**

47

48

* Supply Voltage: built in 8500mAh Li-SOCI2 battery , 2.5v ~~ 3.6v

49

* Operating Temperature: -40 ~~ 85°C

50

51

(% style="color:#037691" %)**I/O Interface:**

52

53

* Battery output (2.6v ~~ 3.6v depends on battery)

54

* +5v controllable output

55

* 3 x Interrupt or Digital IN/OUT pins

56

* 3 x one-wire interfaces

* 1 x UART Interface

* 1 x I2C Interface

(% style="color:#037691" %)**LoRa Spec:**

61

62

* Frequency Range, Band 1 (HF): 862 ~~ 1020 Mhz

63

* Max +22 dBm constant RF output vs.

64

* RX sensitivity: down to -139 dBm.

65

* Excellent blocking immunity

66

67

(% style="color:#037691" %)**Battery:**

68

69

* Li/SOCI2 un-chargeable battery

70

* Capacity: 8500mAh

71

* Self-Discharge: <1% / Year @ 25°C

72

* Max continuously current: 130mA

73

* Max boost current: 2A, 1 second

74

75

(% style="color:#037691" %)**Power Consumption**

76

77

* Sleep Mode: 5uA @ 3.3v

78

* LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm

79

80

== 1.4 Sleep mode and working mode ==

81

82

83

(% style="color:blue" %)**Deep Sleep Mode: **(%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.

84

85

(% style="color:blue" %)**Working Mode:** (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.

86

87

88

== 1.5 Button & LEDs ==

89

90

91

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675071855856-879.png]]

92

93

94

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

95

|=(% style="width: 167px;background-color:#D9E2F3;color:#0070C0" %)**Behavior on ACT**|=(% style="width: 117px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 225px;background-color:#D9E2F3;color:#0070C0" %)**Action**

96

|(% style="width:167px" %)Pressing ACT between 1s < time < 3s|(% style="width:117px" %)Send an uplink|(% style="width:225px" %)(((

97

If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, (% style="color:blue" %)**blue led** (%%)will blink once.

98

Meanwhile, BLE module will be active and user can connect via BLE to configure device.

99

)))

100

|(% style="width:167px" %)Pressing ACT for more than 3s|(% style="width:117px" %)Active Device|(% style="width:225px" %)(((

101

(% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:#037691" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network.

102

(% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.

103

Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device join or not join LoRaWAN network.

104

)))

105

|(% style="width:167px" %)Fast press ACT 5 times.|(% style="width:117px" %)Deactivate Device|(% style="width:225px" %)(% style="color:red" %)**Red led**(%%) will solid on for 5 seconds. Means device is in Deep Sleep Mode.

106

107

== 1.6 BLE connection ==

108

109

110

SN50v3-LB supports BLE remote configure.

111

112

113

BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:

114

115

* Press button to send an uplink

116

* Press button to active device.

117

* Device Power on or reset.

118

119

If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.

120

121

122

== 1.7 Pin Definitions ==

123

124

125

[[image:image-20230513102034-2.png]]

== 1.8 Mechanical ==

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143884058-338.png]]

132

133

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143899218-599.png]]

134

135

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143909447-639.png]]

== Hole Option ==

SN50v3-LB has different hole size options for different size sensor cable. The options provided are M12, M16 and M20. The definition is as below:

142

143

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220627104757-1.png?rev=1.1||alt="image-20220627104757-1.png"]]

144

145

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656298089706-973.png?rev=1.1||alt="1656298089706-973.png"]]

146

147

148

= 2. Configure SN50v3-LB to connect to LoRaWAN network =

149

150

== 2.1 How it works ==

151

152

153

The SN50v3-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the S31x-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.

154

155

156

== 2.2 Quick guide to connect to LoRaWAN server (OTAA) ==

157

158

159

Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.

160

161

The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.

162

163

164

(% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from SN50v3-LB.

165

166

Each SN50v3-LB is shipped with a sticker with the default device EUI as below:

167

168

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/S31-LB_S31B-LB/WebHome/image-20230426084152-1.png?width=502&height=233&rev=1.1||alt="图片-20230426084152-1.png" height="233" width="502"]]

169

170

171

You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:

172

173

174

(% style="color:blue" %)**Register the device**

175

176

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/1654935135620-998.png?rev=1.1||alt="1654935135620-998.png"]]

177

178

179

(% style="color:blue" %)**Add APP EUI and DEV EUI**

180

181

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-4.png?width=753&height=551&rev=1.1||alt="图片-20220611161308-4.png"]]

182

183

184

(% style="color:blue" %)**Add APP EUI in the application**

185

186

187

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-5.png?width=742&height=601&rev=1.1||alt="图片-20220611161308-5.png"]]

188

189

190

(% style="color:blue" %)**Add APP KEY**

191

192

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-6.png?width=744&height=485&rev=1.1||alt="图片-20220611161308-6.png"]]

193

194

195

(% style="color:blue" %)**Step 2:**(%%) Activate SN50v3-LB

196

197

198

Press the button for 5 seconds to activate the SN50v3-LB.

199

200

(% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:blue" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.

201

202

After join success, it will start to upload messages to TTN and you can see the messages in the panel.

203

204

205

== 2.3 Uplink Payload ==

206

207

=== 2.3.1 Device Status, FPORT~=5 ===

208

209

210

Users can use the downlink command(**0x26 01**) to ask SN50v3 to send device configure detail, include device configure status. SN50v3 will uplink a payload via FPort=5 to server.

211

212

The Payload format is as below.

213

214

215

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

216

|(% colspan="6" style="background-color:#d9e2f3; color:#0070c0" %)**Device Status (FPORT=5)**

Example parse in TTNv3

221

222

223

(% style="color:#037691" %)**Sensor Model**(%%): For SN50v3, this value is 0x1C

224

225

(% style="color:#037691" %)**Firmware Version**(%%): 0x0100, Means: v1.0.0 version

226

227

(% style="color:#037691" %)**Frequency Band**:

*0x01: EU868

*0x02: US915

*0x03: IN865

*0x04: AU915

*0x05: KZ865

*0x06: RU864

*0x07: AS923

*0x08: AS923-1

*0x09: AS923-2

*0x0a: AS923-3

*0x0b: CN470

*0x0c: EU433

*0x0d: KR920

*0x0e: MA869

(% style="color:#037691" %)**Sub-Band**:

259

260

AU915 and US915:value 0x00 ~~ 0x08

261

262

CN470: value 0x0B ~~ 0x0C

263

264

Other Bands: Always 0x00

265

266

267

(% style="color:#037691" %)**Battery Info**:

268

269

Check the battery voltage.

Ex1: 0x0B45 = 2885mV

Ex2: 0x0B49 = 2889mV

=== 2.3.2 Working Modes & Sensor Data. Uplink via FPORT~=2 ===

277

278

279

SN50v3 has different working mode for the connections of different type of sensors. This section describes these modes. Use can use the AT Command AT+MOD to set SN50v3 to different working modes.

For example:

**AT+MOD=2 ** ~/~/ will set the SN50v3 to work in MOD=2 distance mode which target to measure distance via Ultrasonic Sensor.

284

285

286

(% style="color:red" %) **Important Notice:**

287

288

1. Some working modes has payload more than 12 bytes, The US915/AU915/AS923 frequency bands' definition has maximum 11 bytes in **DR0**. Server sides will see NULL payload while SN50v3 transmit in DR0 with 12 bytes payload.

289

1. All modes share the same Payload Explanation from HERE.

290

1. By default, the device will send an uplink message every 20 minutes.

291

292

==== 2.3.2.1 MOD~=1 (Default Mode) ====

293

294

295

In this mode, uplink payload includes in total 11 bytes. Uplink packets use FPORT=2.

296

297

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:520px" %)

298

|(% style="background-color:#D9E2F3;color:#0070C0" %)**Size(bytes)**|(% style="background-color:#D9E2F3;color:#0070C0" %)**2**|(% style="width:191px;background-color:#D9E2F3;color:#0070C0" %)**2**|(% style="width:78px;background-color:#D9E2F3;color:#0070C0" %)**2**|(% style="width:216px;background-color:#D9E2F3;color:#0070C0" %)**1**|(% style="width:308px;background-color:#D9E2F3;color:#0070C0" %)**2**|(% style="width:154px;background-color:#D9E2F3;color:#0070C0" %)**2**

299

|**Value**|Bat|(% style="width:191px" %)(((

300

Temperature(DS18B20)

301

(PC13)

302

)))|(% style="width:78px" %)(((

303

ADC

304

(PA4)

305

)))|(% style="width:216px" %)(((

306

Digital in(PB15) &

307

Digital Interrupt(PA8)

308

)))|(% style="width:308px" %)(((

309

Temperature

310

(SHT20 or SHT31 or BH1750 Illumination Sensor)

311

)))|(% style="width:154px" %)(((

Humidity

(SHT20 or SHT31)

)))

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220627150949-6.png?rev=1.1||alt="image-20220627150949-6.png"]]

317

318

319

==== 2.3.2.2 MOD~=2 (Distance Mode) ====

320

321

This mode is target to measure the distance. The payload of this mode is totally 11 bytes. The 8^^th^^ and 9^^th^^ bytes is for the distance.

322

323

(% style="width:1011px" %)

324

325

|**Value**|BAT|(% style="width:196px" %)(((

Temperature(DS18B20)

(PC13)

)))|(% style="width:87px" %)(((

ADC

(PA4)

)))|(% style="width:189px" %)(((

334

Digital in(PB15) &

335

336

Digital Interrupt(PA8)

337

)))|(% style="width:208px" %)(((

Distance measure by:

1) LIDAR-Lite V3HP

Or

2) Ultrasonic Sensor

)))|(% style="width:117px" %)Reserved

343

344

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656324539647-568.png?rev=1.1||alt="1656324539647-568.png"]]

345

346

**Connection of LIDAR-Lite V3HP:**

347

348

[[image:image-20230512173758-5.png||height="563" width="712"]]

349

350

**Connection to Ultrasonic Sensor:**

351

352

Need to remove R1 and R2 resistors to get low power,otherwise there will be 240uA standby current.

353

354

[[image:image-20230512173903-6.png||height="596" width="715"]]

355

356

For the connection to TF-Mini or TF-Luna , MOD2 payload is as below:

357

358

(% style="width:1113px" %)

359

360

|**Value**|BAT|(% style="width:183px" %)(((

Temperature(DS18B20)

(PC13)

)))|(% style="width:173px" %)(((

365

Digital in(PB15) &

366

367

Digital Interrupt(PA8)

368

)))|(% style="width:84px" %)(((

ADC

(PA4)

)))|(% style="width:323px" %)(((

373

Distance measure by:1)TF-Mini plus LiDAR

374

Or

375

2) TF-Luna LiDAR

376

)))|(% style="width:188px" %)Distance signal strength

377

378

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656376779088-686.png?rev=1.1||alt="1656376779088-686.png"]]

379

380

**Connection to [[TF-Mini plus>>url:http://en.benewake.com/product/detail/5c345cd0e5b3a844c472329b.html]] LiDAR(UART version):**

381

382

Need to remove R3 and R4 resistors to get low power,otherwise there will be 400uA standby current.

383

384

[[image:image-20230512180609-7.png||height="555" width="802"]]

385

386

**Connection to [[TF-Luna>>url:http://en.benewake.com/product/detail/5e1c1fd04d839408076b6255.html]] LiDAR (UART version):**

387

388

Need to remove R3 and R4 resistors to get low power,otherwise there will be 400uA standby current.

389

390

[[image:image-20230513105207-4.png||height="469" width="802"]]

391

392

393

==== 2.3.2.3 MOD~=3 (3 ADC + I2C) ====

394

395

This mode has total 12 bytes. Include 3 x ADC + 1x I2C

396

397

(% style="width:1031px" %)

|=(((

**Size(bytes)**

|**Value**|(% style="width:68px" %)(((

ADC1

(PA4)

)))|(% style="width:75px" %)(((

ADC2

(PA5)

)))|(((

ADC3

(PA8)

)))|(((

Digital Interrupt(PB15)

415

)))|(% style="width:304px" %)(((

416

Temperature

417

418

(SHT20 or SHT31 or BH1750 Illumination Sensor)

419

)))|(% style="width:163px" %)(((

Humidity

(SHT20 or SHT31)

)))|(% style="width:53px" %)Bat

424

425

[[image:image-20230513110214-6.png]]

426

427

428

==== 2.3.2.4 MOD~=4 (3 x DS18B20) ====

429

430

431

This mode has total 11 bytes. As shown below:

432

433

(% style="width:1017px" %)

434

435

|**Value**|BAT|(% style="width:186px" %)(((

436

Temperature1(DS18B20)

437

(PC13)

438

)))|(% style="width:82px" %)(((

ADC

(PA4)

)))|(% style="width:210px" %)(((

443

Digital in(PB15) &

444

445

Digital Interrupt(PA8)

446

)))|(% style="width:191px" %)Temperature2(DS18B20)

447

(PB9)|(% style="width:183px" %)Temperature3(DS18B20)

448

(PB8)

449

450

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656377606181-607.png?rev=1.1||alt="1656377606181-607.png"]]

451

452

[[image:image-20230513134006-1.png||height="559" width="736"]]

453

454

455

==== 2.3.2.5 MOD~=5(Weight Measurement by HX711) ====

456

457

[[image:image-20230512164658-2.png||height="532" width="729"]]

458

459

Each HX711 need to be calibrated before used. User need to do below two steps:

460

461

1. Zero calibration. Don't put anything on load cell and run **AT+WEIGRE** to calibrate to Zero gram.

462

1. Adjust calibration factor (default value 400): Put a known weight thing on load cell and run **AT+WEIGAP** to adjust the Calibration Factor.

463

1. (((

464

Weight has 4 bytes, the unit is g.

)))

For example:

**AT+GETSENSORVALUE =0**

470

471

Response: Weight is 401 g

472

473

Check the response of this command and adjust the value to match the real value for thing.

474

475

(% style="width:767px" %)

|=(((

**Size(bytes)**

|**Value**|BAT|(% style="width:193px" %)(((

Temperature(DS18B20)

(PC13)

)))|(% style="width:85px" %)(((

ADC

(PA4)

)))|(% style="width:186px" %)(((

490

Digital in(PB15) &

491

492

Digital Interrupt(PA8)

493

)))|(% style="width:100px" %)Weight

494

495

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220820120036-2.png?width=1003&height=469&rev=1.1||alt="image-20220820120036-2.png" height="469" width="1003"]]

496

497

498

==== 2.3.2.6 MOD~=6 (Counting Mode) ====

499

500

In this mode, the device will work in counting mode. It counts the interrupt on the interrupt pins and sends the count on TDC time.

501

502

Connection is as below. The PIR sensor is a count sensor, it will generate interrupt when people come close or go away. User can replace the PIR sensor with other counting sensors.

503

504

[[image:image-20230512181814-9.png||height="543" width="697"]]

505

506

**Note:** LoRaWAN wireless transmission will infect the PIR sensor. Which cause the counting value increase +1 for every uplink. User can change PIR sensor or put sensor away of the SN50_v3 to avoid this happen.

507

508

(% style="width:961px" %)

509

510

|**Value**|BAT|(% style="width:256px" %)(((

Temperature(DS18B20)

(PC13)

)))|(% style="width:108px" %)(((

ADC

(PA4)

)))|(% style="width:126px" %)(((

Digital in

(PB15)

)))|(% style="width:145px" %)(((

Count

(PA8)

)))

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656378441509-171.png?rev=1.1||alt="1656378441509-171.png"]]

529

530

531

==== 2.3.2.7 MOD~=7 (Three interrupt contact modes) ====

532

533

(% style="width:1108px" %)

|=(((

**Size(bytes)**

|**Value**|BAT|(% style="width:188px" %)(((

Temperature(DS18B20)

(PC13)

)))|(% style="width:83px" %)(((

ADC

(PA5)

)))|(% style="width:184px" %)(((

546

Digital Interrupt1(PA8)

547

)))|(% style="width:186px" %)Digital Interrupt2(PA4)|(% style="width:197px" %)Digital Interrupt3(PB15)|(% style="width:100px" %)Reserved

548

549

[[image:image-20230513111203-7.png||height="324" width="975"]]

550

551

==== 2.3.2.8 MOD~=8 （3ADC+1DS18B20） ====

552

553

(% style="width:922px" %)

|=(((

**Size(bytes)**

|**Value**|BAT|(% style="width:207px" %)(((

Temperature(DS18B20)

(PC13)

)))|(% style="width:94px" %)(((

ADC1

(PA4)

)))|(% style="width:198px" %)(((

566

Digital Interrupt(PB15)

567

)))|(% style="width:84px" %)(((

ADC2

(PA5)

)))|(% style="width:82px" %)(((

ADC3

(PA8)

)))

[[image:image-20230513111231-8.png||height="335" width="900"]]

578

579

580

==== 2.3.2.9 MOD~=9 (3DS18B20+ two Interrupt count mode) ====

581

582

(% style="width:1010px" %)

583

|=(((

584

**Size(bytes)**

585

)))|=**2**|=**2**|=**2**|=**1**|=(% style="width: 193px;" %)**2**|=(% style="width: 78px;" %)4|=(% style="width: 78px;" %)4

586

|**Value**|BAT|(((

587

Temperature1(DS18B20)

(PC13)

)))|(((

Temperature2(DS18B20)

(PB9)

)))|(((

Digital Interrupt

(PB15)

)))|(% style="width:193px" %)(((

599

Temperature3(DS18B20)

600

601

(PB8)

602

)))|(% style="width:78px" %)(((

Count1

(PA8)

)))|(% style="width:78px" %)(((

Count2

(PA4)

)))

[[image:image-20230513111255-9.png||height="341" width="899"]]

613

614

**The newly added AT command is issued correspondingly:**

615

616

**~ AT+INTMOD1** ** PA8** pin： Corresponding downlink: **06 00 00 xx**

617

618

**~ AT+INTMOD2** **PA4** pin： Corresponding downlink:** 06 00 01 xx**

619

620

**~ AT+INTMOD3** **PB15** pin： Corresponding downlink: ** 06 00 02 xx**

**AT+SETCNT=aa,bb**

When AA is 1, set the count of PA8 pin to BB Corresponding downlink：09 01 bb bb bb bb

625

626

When AA is 2, set the count of PA4 pin to BB Corresponding downlink：09 02 bb bb bb bb

=== 2.3.3 Decode payload ===

631

632

While using TTN V3 network, you can add the payload format to decode the payload.

633

634

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656378466788-734.png?rev=1.1||alt="1656378466788-734.png"]]

635

636

The payload decoder function for TTN V3 are here:

637

638

SN50v3 TTN V3 Payload Decoder: [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>url:https://github.com/dragino/dragino-end-node-decoder]]

639

640

641

==== 2.3.3.1 Battery Info ====

642

643

Check the battery voltage for SN50v3.

Ex1: 0x0B45 = 2885mV

Ex2: 0x0B49 = 2889mV

==== 2.3.3.2 Temperature (DS18B20) ====

651

652

If there is a DS18B20 connected to PC13 pin. The temperature will be uploaded in the payload.

653

654

More DS18B20 can check the [[3 DS18B20 mode>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#2.3.4MOD3D4283xDS18B2029]]

**Connection:**

[[image:image-20230512180718-8.png||height="538" width="647"]]

**Example**:

If payload is: 0105H: (0105 & 8000 == 0), temp = 0105H /10 = 26.1 degree

663

664

If payload is: FF3FH : (FF3F & 8000 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.

665

666

（FF3F & 8000：Judge whether the highest bit is 1, when the highest bit is 1, it is negative）

667

668

669

==== 2.3.3.3 Digital Input ====

670

671

The digital input for pin PB15,

672

673

* When PB15 is high, the bit 1 of payload byte 6 is 1.

674

* When PB15 is low, the bit 1 of payload byte 6 is 0.

675

676

(% class="wikigeneratedid" id="H2.3.3.4A0AnalogueDigitalConverter28ADC29" %)

677

(((

678

When the digital interrupt pin is set to AT+INTMODx=0, this pin is used as a digital input pin.

679

680

**Note:**The maximum voltage input supports 3.6V.

)))

==== 2.3.3.4 Analogue Digital Converter (ADC) ====

686

687

The measuring range of the ADC is only about 0V to 1.1V The voltage resolution is about 0.24mv.

688

689

When the measured output voltage of the sensor is not within the range of 0V and 1.1V, the output voltage terminal of the sensor shall be divided The example in the following figure is to reduce the output voltage of the sensor by three times If it is necessary to reduce more times, calculate according to the formula in the figure and connect the corresponding resistance in series.

690

691

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220628150112-1.png?width=285&height=241&rev=1.1||alt="image-20220628150112-1.png" height="241" width="285"]]

692

693

**Note:**If the ADC type sensor needs to be powered by SN50_v3, it is recommended to use +5V to control its switch.Only sensors with low power consumption can be powered with VDD.

694

695

696

==== 2.3.3.5 Digital Interrupt ====

697

698

Digital Interrupt refers to pin PA8, and there are different trigger methods. When there is a trigger, the SN50v3 will send a packet to the server.

699

700

**~ Interrupt connection method:**

701

702

[[image:image-20230513105351-5.png||height="147" width="485"]]

703

704

**Example to use with door sensor :**

705

706

The door sensor is shown at right. It is a two wire magnetic contact switch used for detecting the open/close status of doors or windows.

707

708

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379210849-860.png?rev=1.1||alt="1656379210849-860.png"]]

709

710

When the two pieces are close to each other, the 2 wire output will be short or open (depending on the type), while if the two pieces are away from each other, the 2 wire output will be the opposite status. So we can use SN50_v3 interrupt interface to detect the status for the door or window.

711

712

**~ Below is the installation example:**

713

714

Fix one piece of the magnetic sensor to the door and connect the two pins to SN50_v3 as follows:

715

716

* (((

717

One pin to SN50_v3's PA8 pin

718

)))

719

* (((

720

The other pin to SN50_v3's VDD pin

721

)))

722

723

Install the other piece to the door. Find a place where the two pieces will be close to each other when the door is closed. For this particular magnetic sensor, when the door is closed, the output will be short, and PA8 will be at the VCC voltage.

724

725

Door sensors have two types: ** NC (Normal close)** and **NO (normal open)**. The connection for both type sensors are the same. But the decoding for payload are reverse, user need to modify this in the IoT Server decoder.

726

727

When door sensor is shorted, there will extra power consumption in the circuit, the extra current is 3v3/R14 = 3v3/1Mohm = 3uA which can be ignored.

728

729

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379283019-229.png?rev=1.1||alt="1656379283019-229.png"]]

730

731

The above photos shows the two parts of the magnetic switch fitted to a door.

732

733

The software by default uses the falling edge on the signal line as an interrupt. We need to modify it to accept both the rising edge (0v ~-~-> VCC , door close) and the falling edge (VCC ~-~-> 0v , door open) as the interrupt.

The command is:

**AT+INTMOD1=1 **~/~/(more info about INMOD please refer** **[[**AT Command Manual**>>url:http://www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/&file=DRAGINO_LSN50_AT_Commands_v1.5.1.pdf]]**. **)

738

739

Below shows some screen captures in TTN V3:

740

741

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379339508-835.png?rev=1.1||alt="1656379339508-835.png"]]

742

743

In MOD=1, user can use byte 6 to see the status for door open or close. TTN V3 decoder is as below:

744

745

door= (bytes[6] & 0x80)? "CLOSE":"OPEN";

746

747

748

==== 2.3.3.6 I2C Interface (SHT20 & SHT31) ====

749

750

The SDA and SCK are I2C interface lines. You can use these to connect to an I2C device and get the sensor data.

751

752

We have made an example to show how to use the I2C interface to connect to the SHT20/ SHT31 Temperature and Humidity Sensor.

753

754

Notice: Different I2C sensors have different I2C commands set and initiate process, if user want to use other I2C sensors, User need to re-write the source code to support those sensors. SHT20/ SHT31 code in SN50_v3 will be a good reference.

755

756

Below is the connection to SHT20/ SHT31. The connection is as below:

757

758

759

[[image:image-20230513103633-3.png||height="448" width="716"]]

760

761

The device will be able to get the I2C sensor data now and upload to IoT Server.

762

763

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379664142-345.png?rev=1.1||alt="1656379664142-345.png"]]

764

765

Convert the read byte to decimal and divide it by ten.

**Example:**

Temperature: Read:0116(H) = 278(D) Value: 278 /10=27.8℃;

770

771

Humidity: Read:0248(H)=584(D) Value: 584 / 10=58.4, So 58.4%

772

773

If you want to use other I2C device, please refer the SHT20 part source code as reference.

774

775

776

==== 2.3.3.7 Distance Reading ====

777

778

Refer [[Ultrasonic Sensor section>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#H2.4.8UltrasonicSensor]].

779

780

781

==== 2.3.3.8 Ultrasonic Sensor ====

782

783

This Fundamental Principles of this sensor can be found at this link: [[https:~~/~~/wiki.dfrobot.com/Weather_-_proof_Ultrasonic_Sensor_with_Separate_Probe_SKU~~_~~__SEN0208>>url:https://wiki.dfrobot.com/Weather_-_proof_Ultrasonic_Sensor_with_Separate_Probe_SKU___SEN0208]]

784

785

The SN50_v3 detects the pulse width of the sensor and converts it to mm output. The accuracy will be within 1 centimeter. The usable range (the distance between the ultrasonic probe and the measured object) is between 24cm and 600cm.

786

787

The working principle of this sensor is similar to the **HC-SR04** ultrasonic sensor.

788

789

The picture below shows the connection:

790

791

[[image:image-20230512173903-6.png||height="596" width="715"]]

792

793

Connect to the SN50_v3 and run **AT+MOD=2** to switch to ultrasonic mode (ULT).

794

795

The ultrasonic sensor uses the 8^^th^^ and 9^^th^^ byte for the measurement value.

**Example:**

Distance: Read: 0C2D(Hex) = 3117(D) Value: 3117 mm=311.7 cm

==== 2.3.3.9 Battery Output - BAT pin ====

804

805

The BAT pin of SN50v3 is connected to the Battery directly. If users want to use BAT pin to power an external sensor. User need to make sure the external sensor is of low power consumption. Because the BAT pin is always open. If the external sensor is of high power consumption. the battery of SN50v3-LB will run out very soon.

806

807

808

==== 2.3.3.10 +5V Output ====

809

810

SN50v3 will enable +5V output before all sampling and disable the +5v after all sampling.

811

812

The 5V output time can be controlled by AT Command.

**AT+5VT=1000**

Means set 5V valid time to have 1000ms. So the real 5V output will actually have 1000ms + sampling time for other sensors.

817

818

By default the AT+5VT=500. If the external sensor which require 5v and require more time to get stable state, user can use this command to increase the power ON duration for this sensor.

==== 2.3.3.11 BH1750 Illumination Sensor ====

823

824

MOD=1 support this sensor. The sensor value is in the 8^^th^^ and 9^^th^^ bytes.

825

826

[[image:image-20230512172447-4.png||height="416" width="712"]]

827

828

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220628110012-12.png?rev=1.1||alt="image-20220628110012-12.png" height="361" width="953"]]

829

830

831

==== 2.3.3.12 Working MOD ====

832

833

The working MOD info is contained in the Digital in & Digital Interrupt byte (7^^th^^ Byte).

834

835

User can use the 3^^rd^^ ~~ 7^^th^^ bit of this byte to see the working mod:

836

837

Case 7^^th^^ Byte >> 2 & 0x1f:

* 0: MOD1

* 1: MOD2

* 2: MOD3

* 3: MOD4

* 4: MOD5

* 5: MOD6

* 6: MOD7

* 7: MOD8

* 8: MOD9

== ==

== 2.4 Payload Decoder file ==

852

853

854

In TTN, use can add a custom payload so it shows friendly reading

855

856

In the page (% style="color:#037691" %)**Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder**(%%) to add the decoder from:

857

858

[[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/SN50_v3-LB>>https://github.com/dragino/dragino-end-node-decoder/tree/main/SN50_v3-LB]]

== 2.5 Frequency Plans ==

863

864

865

The SN50v3-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.

866

867

[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]

868

869

870

= 3. Configure SN50v3-LB =

871

872

== 3.1 Configure Methods ==

873

874

875

SN50v3-LB supports below configure method:

876

877

* AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].

878

* AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].

879

* LoRaWAN Downlink. Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.

880

881

== 3.2 General Commands ==

882

883

884

These commands are to configure:

885

886

* General system settings like: uplink interval.

887

* LoRaWAN protocol & radio related command.

888

889

They are same for all Dragino Devices which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:

890

891

[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]

892

893

894

== 3.3 Commands special design for SN50v3-LB ==

895

896

897

These commands only valid for S31x-LB, as below:

898

899

900

=== 3.3.1 Set Transmit Interval Time ===

901

902

Feature: Change LoRaWAN End Node Transmit Interval.

903

904

(% style="color:blue" %)**AT Command: AT+TDC**

905

906

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

907

|=(% style="width: 156px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 137px;background-color:#D9E2F3" %)**Function**|=(% style="background-color:#D9E2F3" %)**Response**

908

|(% style="width:156px" %)AT+TDC=?|(% style="width:137px" %)Show current transmit Interval|(((

909

30000

910

OK

911

the interval is 30000ms = 30s

912

)))

913

|(% style="width:156px" %)AT+TDC=60000|(% style="width:137px" %)Set Transmit Interval|(((

914

OK

915

Set transmit interval to 60000ms = 60 seconds

916

)))

917

918

(% style="color:blue" %)**Downlink Command: 0x01**

919

920

Format: Command Code (0x01) followed by 3 bytes time value.

921

922

If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.

923

924

* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds

925

* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds

=== ===

=== 3.3.2 Get Device Status ===

930

931

Send a LoRaWAN downlink to ask the device to send its status.

932

933

(% style="color:blue" %)**Downlink Payload: **(%%)0x26 01

934

935

Sensor will upload Device Status via FPORT=5. See payload section for detail.

936

937

938

=== 3.3.3 Set Interrupt Mode ===

939

940

Feature, Set Interrupt mode for GPIO_EXIT.

941

942

(% style="color:blue" %)**AT Command: AT+INTMOD1，AT+INTMOD2，AT+INTMOD3**

943

944

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

945

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

946

|(% style="width:154px" %)AT+INTMOD1=?|(% style="width:196px" %)Show current interrupt mode|(% style="width:157px" %)(((

947

0

948

OK

949

the mode is 0 =Disable Interrupt

950

)))

951

|(% style="width:154px" %)AT+INTMOD1=2|(% style="width:196px" %)(((

952

Set Transmit Interval

953

0. (Disable Interrupt),

954

~1. (Trigger by rising and falling edge)

955

2. (Trigger by falling edge)

956

3. (Trigger by rising edge)

957

)))|(% style="width:157px" %)OK

958

|(% style="width:154px" %)AT+INTMOD2=3|(% style="width:196px" %)(((

959

Set Transmit Interval

960

961

trigger by rising edge.

962

)))|(% style="width:157px" %)OK

963

|(% style="width:154px" %)AT+INTMOD3=0|(% style="width:196px" %)Disable Interrupt|(% style="width:157px" %)OK

964

965

(% style="color:blue" %)**Downlink Command: 0x06**

966

967

Format: Command Code (0x06) followed by 3 bytes.

968

969

This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.

970

971

* Example 1: Downlink Payload: 06000000 **~-~-->** AT+INTMOD1=0

972

* Example 2: Downlink Payload: 06000003 **~-~-->** AT+INTMOD1=3

973

* Example 3: Downlink Payload: 06000102 **~-~-->** AT+INTMOD2=2

974

* Example 4: Downlink Payload: 06000201 **~-~-->** AT+INTMOD3=1

=== ===

=== 3.3.4 Set Power Output Duration ===

979

980

Control the output duration 5V . Before each sampling, device will

981

982

~1. first enable the power output to external sensor,

983

984

2. keep it on as per duration, read sensor value and construct uplink payload

985

986

3. final, close the power output.

987

988

(% style="color:blue" %)**AT Command: AT+5VT**

989

990

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

991

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

992

|(% style="width:154px" %)AT+5VT=?|(% style="width:196px" %)Show 5V open time.|(% style="width:157px" %)(((

500(default)

OK

)))

|(% style="width:154px" %)AT+5VT=1000|(% style="width:196px" %)(((

998

Close after a delay of 1000 milliseconds.

999

)))|(% style="width:157px" %)OK

1000

1001

(% style="color:blue" %)**Downlink Command: 0x07**

1002

1003

Format: Command Code (0x07) followed by 2 bytes.

1004

1005

The first and second bytes are the time to turn on.

1006

1007

* Example 1: Downlink Payload: 070000 **~-~-->** AT+5VT=0

1008

* Example 2: Downlink Payload: 0701F4 **~-~-->** AT+5VT=500

=== ===

=== 3.3.5 Set Weighing parameters ===

1013

1014

Feature: Working mode 5 is effective, weight initialization and weight factor setting of HX711.

1015

1016

(% style="color:blue" %)**AT Command: AT+WEIGRE,AT+WEIGAP**

1017

1018

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

1019

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

1020

|(% style="width:154px" %)AT+WEIGRE|(% style="width:196px" %)Weight is initialized to 0.|(% style="width:157px" %)OK

1021

|(% style="width:154px" %)AT+WEIGAP=？|(% style="width:196px" %)400.0|(% style="width:157px" %)OK(default)

1022

|(% style="width:154px" %)AT+WEIGAP=400.3|(% style="width:196px" %)Set the factor to 400.3.|(% style="width:157px" %)OK

1023

1024

(% style="color:blue" %)**Downlink Command: 0x08**

1025

1026

Format: Command Code (0x08) followed by 2 bytes or 4 bytes.

1027

1028

Use AT+WEIGRE when the first byte is 1, only 1 byte. When it is 2, use AT+WEIGAP, there are 3 bytes.

1029

1030

The second and third bytes are multiplied by 10 times to be the AT+WEIGAP value.

1031

1032

* Example 1: Downlink Payload: 0801 **~-~-->** AT+WEIGRE

1033

* Example 2: Downlink Payload: 08020FA3 **~-~-->** AT+WEIGAP=400.3

1034

* Example 3: Downlink Payload: 08020FA0 **~-~-->** AT+WEIGAP=400.0

=== ===

=== 3.3.6 Set Digital pulse count value ===

1039

1040

Feature: Set the pulse count value.

1041

1042

Count 1 is PA8 pin of mode 6 and mode 9. Count 2 is PA4 pin of mode 9.

1043

1044

(% style="color:blue" %)**AT Command: AT+SETCNT**

1045

1046

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

1047

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

1048

|(% style="width:154px" %)AT+SETCNT=1,100|(% style="width:196px" %)Initialize the count value 1 to 100.|(% style="width:157px" %)OK

1049

|(% style="width:154px" %)AT+SETCNT=2,0|(% style="width:196px" %)Initialize the count value 2 to 0.|(% style="width:157px" %)OK

1050

1051

(% style="color:blue" %)**Downlink Command: 0x09**

1052

1053

Format: Command Code (0x09) followed by 5 bytes.

1054

1055

The first byte is to select which count value to initialize, and the next four bytes are the count value to be initialized.

1056

1057

* Example 1: Downlink Payload: 090100000000 **~-~-->** AT+SETCNT=1,0

1058

* Example 2: Downlink Payload: 0902000003E8 **~-~-->** AT+SETCNT=2,1000

=== ===

=== 3.3.7 Set Workmode ===

1063

1064

Feature: Switch working mode.

1065

1066

(% style="color:blue" %)**AT Command: AT+MOD**

1067

1068

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

1069

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

1070

|(% style="width:154px" %)AT+MOD=?|(% style="width:196px" %)Get the current working mode.|(% style="width:157px" %)(((

1071

OK

1072

)))

1073

|(% style="width:154px" %)AT+MOD=4|(% style="width:196px" %)Set the working mode to 3DS18B20s.|(% style="width:157px" %)(((

1074

OK

1075

1076

Attention:Take effect after ATZ

1077

)))

1078

1079

(% style="color:blue" %)**Downlink Command: 0x0A**

1080

1081

Format: Command Code (0x0A) followed by 1 bytes.

1082

1083

* Example 1: Downlink Payload: 0A01 **~-~-->** AT+MOD=1

1084

* Example 2: Downlink Payload: 0A04 **~-~-->** AT+MOD=4

= =

= 4. Battery & Power Consumption =

1089

1090

1091

SN50v3-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.

1092

1093

[[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .

1094

1095

1096

= 5. OTA Firmware update =

1097

1098

1099

(% class="wikigeneratedid" %)

1100

User can change firmware SN50v3-LB to:

1101

1102

* Change Frequency band/ region.

1103

* Update with new features.

1104

* Fix bugs.

1105

1106

Firmware and changelog can be downloaded from : **[[Firmware download link>>url:https://www.dropbox.com/sh/kwqv57tp6pejias/AAAopYMATh1GM6fZ-VRCLrpDa?dl=0]]**

1107

1108

1109

Methods to Update Firmware:

1110

1111

* (Recommanded way) OTA firmware update via wireless: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]

1112

* Update through UART TTL interface.**[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.

= 6. FAQ =

== 6.1 Where can i find source code of SN50v3-LB? ==

1117

1118

* **[[Hardware Source Files>>https://github.com/dragino/Lora/tree/master/LSN50/v3.0]].**

1119

* **[[Software Source Code & Compile instruction>>https://github.com/dragino/SN50v3]].**

= 7. Order Info =

Part Number: (% style="color:blue" %)**SN50v3-LB-XX-YY**

1125

1126

(% style="color:red" %)**XX**(%%): The default frequency band

1127

1128

* (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band

1129

* (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band

1130

* (% style="color:red" %)**EU433**(%%): LoRaWAN EU433 band

1131

* (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band

1132

* (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band

1133

* (% style="color:red" %)**US915**(%%): LoRaWAN US915 band

1134

* (% style="color:red" %)**IN865**(%%): LoRaWAN IN865 band

1135

* (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band

1136

1137

(% style="color:red" %)**YY: ** (%%)Hole Option

1138

1139

* (% style="color:red" %)**12**(%%): With M12 waterproof cable hole

1140

* (% style="color:red" %)**16**(%%): With M16 waterproof cable hole

1141

* (% style="color:red" %)**20**(%%): With M20 waterproof cable hole

1142

* (% style="color:red" %)**NH**(%%): No Hole

= 8. Packing Info =

(% style="color:#037691" %)**Package Includes**:

1147

1148

* SN50v3-LB LoRaWAN Generic Node

1149

1150

(% style="color:#037691" %)**Dimension and weight**:

* Device Size: cm

* Device Weight: g

* Package Size / pcs : cm

* Weight / pcs : g

= 9. Support =

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

1161

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.cc>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.cc]]

Wiki source code of SN50v3-LB LoRaWAN Sensor Node User Manual

Applications

Navigation