SN50v3-LB LoRaWAN Sensor Node User Manual

(% style="color:blue" %)**SN50V3-LB **(%%)LoRaWAN Sensor Node is a Long Range LoRa Sensor Node. It is designed for outdoor use and powered by (% style="color:blue" %)** 8500mA Li/SOCl2 battery**(%%) for long term use.SN50V3-LB is designed to facilitate developers to quickly deploy industrial level LoRa and IoT solutions. It help users to turn the idea into a practical application and make the Internet of Things a reality. It is easy to program, create and connect your things everywhere.

21

22

(% style="color:blue" %)**SN50V3-LB wireless part**(%%) is based on SX1262 allows the user to send data and reach extremely long ranges at low data-rates.It provides ultra-long range spread spectrum communication and high interference immunity whilst minimising current consumption.It targets professional wireless sensor network applications such as irrigation systems, smart metering, smart cities, smartphone detection, building automation, and so on.

23

24

(% style="color:blue" %)**SN50V3-LB **(%%)has a powerful 48Mhz ARM microcontroller with 256KB flash and 64KB RAM. It has multiplex I/O pins to connect to different sensors.

25

26

(% style="color:blue" %)**SN50V3-LB**(%%) has a built-in BLE module, user can configure the sensor remotely via Mobile Phone. It also support OTA upgrade via private LoRa protocol for easy maintaining.

27

28

SN50V3-LB is the 3^^rd^^ generation of LSN50 series generic sensor node from Dragino. It is an (% style="color:blue" %)**open source project**(%%) and has a mature LoRaWAN stack and application software. User can use the pre-load software for their IoT projects or easily customize the software for different requirements.

== 1.2 Features ==

* LoRaWAN 1.0.3 Class A

34

* Ultra-low power consumption

35

* Open-Source hardware/software

36

* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865

37

* Support Bluetooth v5.1 and LoRaWAN remote configure

38

* Support wireless OTA update firmware

39

* Uplink on periodically

40

* Downlink to change configure

41

* 8500mAh Battery for long term use

42

43

== 1.3 Specification ==

44

45

46

(% style="color:#037691" %)**Common DC Characteristics:**

47

48

* Supply Voltage: built in 8500mAh Li-SOCI2 battery , 2.5v ~~ 3.6v

49

* Operating Temperature: -40 ~~ 85°C

50

51

(% style="color:#037691" %)**I/O Interface:**

52

53

* Battery output (2.6v ~~ 3.6v depends on battery)

54

* +5v controllable output

55

* 3 x Interrupt or Digital IN/OUT pins

56

* 3 x one-wire interfaces

* 1 x UART Interface

* 1 x I2C Interface

(% style="color:#037691" %)**LoRa Spec:**

61

62

* Frequency Range, Band 1 (HF): 862 ~~ 1020 Mhz

63

* Max +22 dBm constant RF output vs.

64

* RX sensitivity: down to -139 dBm.

65

* Excellent blocking immunity

66

67

(% style="color:#037691" %)**Battery:**

68

69

* Li/SOCI2 un-chargeable battery

70

* Capacity: 8500mAh

71

* Self-Discharge: <1% / Year @ 25°C

72

* Max continuously current: 130mA

73

* Max boost current: 2A, 1 second

74

75

(% style="color:#037691" %)**Power Consumption**

76

77

* Sleep Mode: 5uA @ 3.3v

78

* LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm

79

80

== 1.4 Sleep mode and working mode ==

81

82

83

(% style="color:blue" %)**Deep Sleep Mode: **(%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.

84

85

(% style="color:blue" %)**Working Mode:** (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.

86

87

88

== 1.5 Button & LEDs ==

89

90

91

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675071855856-879.png]]

92

93

94

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

95

|=(% style="width: 167px;background-color:#D9E2F3;color:#0070C0" %)**Behavior on ACT**|=(% style="width: 117px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 225px;background-color:#D9E2F3;color:#0070C0" %)**Action**

96

|(% style="width:167px" %)Pressing ACT between 1s < time < 3s|(% style="width:117px" %)Send an uplink|(% style="width:225px" %)(((

97

If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, (% style="color:blue" %)**blue led** (%%)will blink once.

98

Meanwhile, BLE module will be active and user can connect via BLE to configure device.

99

)))

100

|(% style="width:167px" %)Pressing ACT for more than 3s|(% style="width:117px" %)Active Device|(% style="width:225px" %)(((

101

(% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:#037691" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network.

102

(% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.

103

Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device join or not join LoRaWAN network.

104

)))

105

|(% style="width:167px" %)Fast press ACT 5 times.|(% style="width:117px" %)Deactivate Device|(% style="width:225px" %)(% style="color:red" %)**Red led**(%%) will solid on for 5 seconds. Means device is in Deep Sleep Mode.

106

107

== 1.6 BLE connection ==

108

109

110

SN50v3-LB supports BLE remote configure.

111

112

113

BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:

114

115

* Press button to send an uplink

116

* Press button to active device.

117

* Device Power on or reset.

118

119

If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.

120

121

122

== 1.7 Pin Definitions ==

123

124

125

[[image:image-20230513102034-2.png]]

== 1.8 Mechanical ==

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143884058-338.png]]

132

133

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143899218-599.png]]

134

135

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143909447-639.png]]

== Hole Option ==

SN50v3-LB has different hole size options for different size sensor cable. The options provided are M12, M16 and M20. The definition is as below:

142

143

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220627104757-1.png?rev=1.1||alt="image-20220627104757-1.png"]]

144

145

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656298089706-973.png?rev=1.1||alt="1656298089706-973.png"]]

146

147

148

= 2. Configure SN50v3-LB to connect to LoRaWAN network =

149

150

== 2.1 How it works ==

151

152

153

The SN50v3-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the S31x-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.

154

155

156

== 2.2 Quick guide to connect to LoRaWAN server (OTAA) ==

157

158

159

Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.

160

161

The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.

162

163

164

(% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from SN50v3-LB.

165

166

Each SN50v3-LB is shipped with a sticker with the default device EUI as below:

167

168

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/S31-LB_S31B-LB/WebHome/image-20230426084152-1.png?width=502&height=233&rev=1.1||alt="图片-20230426084152-1.png" height="233" width="502"]]

169

170

171

You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:

172

173

174

(% style="color:blue" %)**Register the device**

175

176

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/1654935135620-998.png?rev=1.1||alt="1654935135620-998.png"]]

177

178

179

(% style="color:blue" %)**Add APP EUI and DEV EUI**

180

181

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-4.png?width=753&height=551&rev=1.1||alt="图片-20220611161308-4.png"]]

182

183

184

(% style="color:blue" %)**Add APP EUI in the application**

185

186

187

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-5.png?width=742&height=601&rev=1.1||alt="图片-20220611161308-5.png"]]

188

189

190

(% style="color:blue" %)**Add APP KEY**

191

192

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-6.png?width=744&height=485&rev=1.1||alt="图片-20220611161308-6.png"]]

193

194

195

(% style="color:blue" %)**Step 2:**(%%) Activate SN50v3-LB

196

197

198

Press the button for 5 seconds to activate the SN50v3-LB.

199

200

(% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:blue" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.

201

202

After join success, it will start to upload messages to TTN and you can see the messages in the panel.

203

204

205

== 2.3 Uplink Payload ==

206

207

=== 2.3.1 Device Status, FPORT~=5 ===

208

209

210

Users can use the downlink command(**0x26 01**) to ask SN50v3 to send device configure detail, include device configure status. SN50v3 will uplink a payload via FPort=5 to server.

211

212

The Payload format is as below.

213

214

215

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

216

|(% colspan="6" style="background-color:#d9e2f3; color:#0070c0" %)**Device Status (FPORT=5)**

Example parse in TTNv3

221

222

223

(% style="color:#037691" %)**Sensor Model**(%%): For SN50v3, this value is 0x1C

224

225

(% style="color:#037691" %)**Firmware Version**(%%): 0x0100, Means: v1.0.0 version

226

227

(% style="color:#037691" %)**Frequency Band**:

*0x01: EU868

*0x02: US915

*0x03: IN865

*0x04: AU915

*0x05: KZ865

*0x06: RU864

*0x07: AS923

*0x08: AS923-1

*0x09: AS923-2

*0x0a: AS923-3

*0x0b: CN470

*0x0c: EU433

*0x0d: KR920

*0x0e: MA869

(% style="color:#037691" %)**Sub-Band**:

259

260

AU915 and US915:value 0x00 ~~ 0x08

261

262

CN470: value 0x0B ~~ 0x0C

263

264

Other Bands: Always 0x00

265

266

267

(% style="color:#037691" %)**Battery Info**:

268

269

Check the battery voltage.

Ex1: 0x0B45 = 2885mV

Ex2: 0x0B49 = 2889mV

=== 2.3.2 Working Modes & Sensor Data. Uplink via FPORT~=2 ===

277

278

279

SN50v3 has different working mode for the connections of different type of sensors. This section describes these modes. Use can use the AT Command AT+MOD to set SN50v3 to different working modes.

For example:

**AT+MOD=2 ** ~/~/ will set the SN50v3 to work in MOD=2 distance mode which target to measure distance via Ultrasonic Sensor.

284

285

286

(% style="color:red" %) **Important Notice:**

287

288

1. Some working modes has payload more than 12 bytes, The US915/AU915/AS923 frequency bands' definition has maximum 11 bytes in **DR0**. Server sides will see NULL payload while SN50v3 transmit in DR0 with 12 bytes payload.

289

1. All modes share the same Payload Explanation from HERE.

290

1. By default, the device will send an uplink message every 20 minutes.

291

292

==== 2.3.2.1 MOD~=1 (Default Mode) ====

293

294

295

In this mode, uplink payload includes in total 11 bytes. Uplink packets use FPORT=2.

296

297

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:520px" %)

298

|(% style="width:50px;background-color:#D9E2F3;color:#0070C0" %)**Size(bytes)**|(% style="width:20px;background-color:#D9E2F3;color:#0070C0" %)**2**|(% style="width:100px;background-color:#D9E2F3;color:#0070C0" %)**2**|(% style="width:35px;background-color:#D9E2F3;color:#0070C0" %)**2**|(% style="width:90px;background-color:#D9E2F3;color:#0070C0" %)**1**|(% style="width:120px;background-color:#D9E2F3;color:#0070C0" %)**2**|(% style="width:90px;background-color:#D9E2F3;color:#0070C0" %)**2**

299

|**Value**|Bat|(% style="width:191px" %)(((

300

Temperature(DS18B20)(PC13)

301

)))|(% style="width:78px" %)(((

302

ADC(PA4)

303

)))|(% style="width:216px" %)(((

304

Digital in(PB15)&Digital Interrupt(PA8)

305

)))|(% style="width:308px" %)(((

306

Temperature(SHT20 or SHT31 or BH1750 Illumination Sensor)

307

)))|(% style="width:154px" %)(((

308

Humidity(SHT20 or SHT31)

309

)))

310

311

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220627150949-6.png?rev=1.1||alt="image-20220627150949-6.png"]]

312

313

314

==== 2.3.2.2 MOD~=2 (Distance Mode) ====

315

316

This mode is target to measure the distance. The payload of this mode is totally 11 bytes. The 8^^th^^ and 9^^th^^ bytes is for the distance.

317

318

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:520px" %)

319

|(% style="width:40px;background-color:#D9E2F3;color:#0070C0" %)**Size(bytes)**|(% style="width:40px;background-color:#D9E2F3;color:#0070C0" %)**2**|(% style="width:110px;background-color:#D9E2F3;color:#0070C0" %)**2**|(% style="width:40px;background-color:#D9E2F3;color:#0070C0" %)**2**|(% style="width:110px;background-color:#D9E2F3;color:#0070C0" %)**1**|(% style="width:140px;background-color:#D9E2F3;color:#0070C0" %)**2**|(% style="width:40px;background-color:#D9E2F3;color:#0070C0" %)**2**

320

|**Value**|BAT|(% style="width:196px" %)(((

321

Temperature(DS18B20)(PC13)

322

)))|(% style="width:87px" %)(((

323

ADC(PA4)

324

)))|(% style="width:189px" %)(((

325

Digital in(PB15) & Digital Interrupt(PA8)

326

)))|(% style="width:208px" %)(((

327

Distance measure by:1) LIDAR-Lite V3HP

328

Or 2) Ultrasonic Sensor

329

)))|(% style="width:117px" %)Reserved

330

331

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656324539647-568.png?rev=1.1||alt="1656324539647-568.png"]]

332

333

**Connection of LIDAR-Lite V3HP:**

334

335

[[image:image-20230512173758-5.png||height="563" width="712"]]

336

337

**Connection to Ultrasonic Sensor:**

338

339

Need to remove R1 and R2 resistors to get low power,otherwise there will be 240uA standby current.

340

341

[[image:image-20230512173903-6.png||height="596" width="715"]]

342

343

For the connection to TF-Mini or TF-Luna , MOD2 payload is as below:

344

345

(% style="width:1113px" %)

346

347

|**Value**|BAT|(% style="width:183px" %)(((

348

Temperature(DS18B20)

349

(PC13)

350

)))|(% style="width:173px" %)(((

351

Digital in(PB15) &

352

Digital Interrupt(PA8)

353

)))|(% style="width:84px" %)(((

354

ADC

355

(PA4)

356

)))|(% style="width:323px" %)(((

357

Distance measure by:1)TF-Mini plus LiDAR

358

Or

359

2) TF-Luna LiDAR

360

)))|(% style="width:188px" %)Distance signal strength

361

362

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656376779088-686.png?rev=1.1||alt="1656376779088-686.png"]]

363

364

**Connection to [[TF-Mini plus>>url:http://en.benewake.com/product/detail/5c345cd0e5b3a844c472329b.html]] LiDAR(UART version):**

365

366

Need to remove R3 and R4 resistors to get low power,otherwise there will be 400uA standby current.

367

368

[[image:image-20230512180609-7.png||height="555" width="802"]]

369

370

**Connection to [[TF-Luna>>url:http://en.benewake.com/product/detail/5e1c1fd04d839408076b6255.html]] LiDAR (UART version):**

371

372

Need to remove R3 and R4 resistors to get low power,otherwise there will be 400uA standby current.

373

374

[[image:image-20230513105207-4.png||height="469" width="802"]]

375

376

377

==== 2.3.2.3 MOD~=3 (3 ADC + I2C) ====

378

379

This mode has total 12 bytes. Include 3 x ADC + 1x I2C

380

381

(% style="width:1031px" %)

|=(((

**Size(bytes)**

|**Value**|(% style="width:68px" %)(((

386

ADC1

387

(PA4)

388

)))|(% style="width:75px" %)(((

ADC2

(PA5)

)))|(((

ADC3

(PA8)

)))|(((

Digital Interrupt(PB15)

396

)))|(% style="width:304px" %)(((

397

Temperature

398

(SHT20 or SHT31 or BH1750 Illumination Sensor)

399

)))|(% style="width:163px" %)(((

400

Humidity

401

(SHT20 or SHT31)

402

)))|(% style="width:53px" %)Bat

403

404

[[image:image-20230513110214-6.png]]

405

406

407

==== 2.3.2.4 MOD~=4 (3 x DS18B20) ====

408

409

410

This mode has total 11 bytes. As shown below:

411

412

(% style="width:1017px" %)

413

414

|**Value**|BAT|(% style="width:186px" %)(((

415

Temperature1(DS18B20)

416

(PC13)

417

)))|(% style="width:82px" %)(((

418

ADC

419

(PA4)

420

)))|(% style="width:210px" %)(((

421

Digital in(PB15) &

422

Digital Interrupt(PA8)

423

)))|(% style="width:191px" %)Temperature2(DS18B20)

424

(PB9)|(% style="width:183px" %)Temperature3(DS18B20)

425

(PB8)

426

427

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656377606181-607.png?rev=1.1||alt="1656377606181-607.png"]]

428

429

[[image:image-20230513134006-1.png||height="559" width="736"]]

430

431

432

==== 2.3.2.5 MOD~=5(Weight Measurement by HX711) ====

433

434

[[image:image-20230512164658-2.png||height="532" width="729"]]

435

436

Each HX711 need to be calibrated before used. User need to do below two steps:

437

438

1. Zero calibration. Don't put anything on load cell and run **AT+WEIGRE** to calibrate to Zero gram.

439

1. Adjust calibration factor (default value 400): Put a known weight thing on load cell and run **AT+WEIGAP** to adjust the Calibration Factor.

440

1. (((

441

Weight has 4 bytes, the unit is g.

)))

For example:

**AT+GETSENSORVALUE =0**

447

448

Response: Weight is 401 g

449

450

Check the response of this command and adjust the value to match the real value for thing.

451

452

(% style="width:767px" %)

|=(((

**Size(bytes)**

|**Value**|BAT|(% style="width:193px" %)(((

457

Temperature(DS18B20)

458

(PC13)

459

)))|(% style="width:85px" %)(((

460

ADC

461

(PA4)

462

)))|(% style="width:186px" %)(((

463

Digital in(PB15) &

464

Digital Interrupt(PA8)

465

)))|(% style="width:100px" %)Weight

466

467

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220820120036-2.png?width=1003&height=469&rev=1.1||alt="image-20220820120036-2.png" height="469" width="1003"]]

468

469

470

==== 2.3.2.6 MOD~=6 (Counting Mode) ====

471

472

In this mode, the device will work in counting mode. It counts the interrupt on the interrupt pins and sends the count on TDC time.

473

474

Connection is as below. The PIR sensor is a count sensor, it will generate interrupt when people come close or go away. User can replace the PIR sensor with other counting sensors.

475

476

[[image:image-20230512181814-9.png||height="543" width="697"]]

477

478

**Note:** LoRaWAN wireless transmission will infect the PIR sensor. Which cause the counting value increase +1 for every uplink. User can change PIR sensor or put sensor away of the SN50_v3 to avoid this happen.

479

480

(% style="width:961px" %)

481

482

|**Value**|BAT|(% style="width:256px" %)(((

Temperature(DS18B20)

(PC13)

)))|(% style="width:108px" %)(((

487

ADC

488

(PA4)

489

)))|(% style="width:126px" %)(((

490

Digital in

491

(PB15)

492

)))|(% style="width:145px" %)(((

Count

(PA8)

)))

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656378441509-171.png?rev=1.1||alt="1656378441509-171.png"]]

498

499

500

==== 2.3.2.7 MOD~=7 (Three interrupt contact modes) ====

501

502

(% style="width:1108px" %)

|=(((

**Size(bytes)**

|**Value**|BAT|(% style="width:188px" %)(((

507

Temperature(DS18B20)

508

(PC13)

509

)))|(% style="width:83px" %)(((

510

ADC

511

(PA5)

512

)))|(% style="width:184px" %)(((

513

Digital Interrupt1(PA8)

514

)))|(% style="width:186px" %)Digital Interrupt2(PA4)|(% style="width:197px" %)Digital Interrupt3(PB15)|(% style="width:100px" %)Reserved

515

516

[[image:image-20230513111203-7.png||height="324" width="975"]]

517

518

==== 2.3.2.8 MOD~=8 （3ADC+1DS18B20） ====

519

520

(% style="width:922px" %)

|=(((

**Size(bytes)**

|**Value**|BAT|(% style="width:207px" %)(((

525

Temperature(DS18B20)

526

(PC13)

527

)))|(% style="width:94px" %)(((

528

ADC1

529

(PA4)

530

)))|(% style="width:198px" %)(((

531

Digital Interrupt(PB15)

532

)))|(% style="width:84px" %)(((

533

ADC2

534

(PA5)

535

)))|(% style="width:82px" %)(((

ADC3

(PA8)

)))

[[image:image-20230513111231-8.png||height="335" width="900"]]

541

542

543

==== 2.3.2.9 MOD~=9 (3DS18B20+ two Interrupt count mode) ====

544

545

(% style="width:1010px" %)

546

|=(((

547

**Size(bytes)**

548

)))|=**2**|=**2**|=**2**|=**1**|=(% style="width: 193px;" %)**2**|=(% style="width: 78px;" %)4|=(% style="width: 78px;" %)4

549

|**Value**|BAT|(((

550

Temperature1(DS18B20)

551

(PC13)

552

)))|(((

553

Temperature2(DS18B20)

(PB9)

)))|(((

Digital Interrupt

(PB15)

)))|(% style="width:193px" %)(((

559

Temperature3(DS18B20)

560

(PB8)

561

)))|(% style="width:78px" %)(((

562

Count1

563

(PA8)

564

)))|(% style="width:78px" %)(((

Count2

(PA4)

)))

[[image:image-20230513111255-9.png||height="341" width="899"]]

570

571

**The newly added AT command is issued correspondingly:**

572

573

**~ AT+INTMOD1** ** PA8** pin： Corresponding downlink: **06 00 00 xx**

574

575

**~ AT+INTMOD2** **PA4** pin： Corresponding downlink:** 06 00 01 xx**

576

577

**~ AT+INTMOD3** **PB15** pin： Corresponding downlink: ** 06 00 02 xx**

**AT+SETCNT=aa,bb**

When AA is 1, set the count of PA8 pin to BB Corresponding downlink：09 01 bb bb bb bb

582

583

When AA is 2, set the count of PA4 pin to BB Corresponding downlink：09 02 bb bb bb bb

=== 2.3.3 Decode payload ===

588

589

While using TTN V3 network, you can add the payload format to decode the payload.

590

591

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656378466788-734.png?rev=1.1||alt="1656378466788-734.png"]]

592

593

The payload decoder function for TTN V3 are here:

594

595

SN50v3 TTN V3 Payload Decoder: [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>url:https://github.com/dragino/dragino-end-node-decoder]]

596

597

598

==== 2.3.3.1 Battery Info ====

599

600

Check the battery voltage for SN50v3.

Ex1: 0x0B45 = 2885mV

Ex2: 0x0B49 = 2889mV

==== 2.3.3.2 Temperature (DS18B20) ====

608

609

If there is a DS18B20 connected to PC13 pin. The temperature will be uploaded in the payload.

610

611

More DS18B20 can check the [[3 DS18B20 mode>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#2.3.4MOD3D4283xDS18B2029]]

**Connection:**

[[image:image-20230512180718-8.png||height="538" width="647"]]

**Example**:

If payload is: 0105H: (0105 & 8000 == 0), temp = 0105H /10 = 26.1 degree

620

621

If payload is: FF3FH : (FF3F & 8000 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.

622

623

（FF3F & 8000：Judge whether the highest bit is 1, when the highest bit is 1, it is negative）

624

625

626

==== 2.3.3.3 Digital Input ====

627

628

The digital input for pin PB15,

629

630

* When PB15 is high, the bit 1 of payload byte 6 is 1.

631

* When PB15 is low, the bit 1 of payload byte 6 is 0.

632

633

(% class="wikigeneratedid" id="H2.3.3.4A0AnalogueDigitalConverter28ADC29" %)

634

(((

635

When the digital interrupt pin is set to AT+INTMODx=0, this pin is used as a digital input pin.

636

637

(% style="color:red" %)**Note:**The maximum voltage input supports 3.6V.

638

)))

639

640

==== 2.3.3.4 Analogue Digital Converter (ADC) ====

641

642

The measuring range of the ADC is only about 0V to 1.1V The voltage resolution is about 0.24mv.

643

644

When the measured output voltage of the sensor is not within the range of 0V and 1.1V, the output voltage terminal of the sensor shall be divided The example in the following figure is to reduce the output voltage of the sensor by three times If it is necessary to reduce more times, calculate according to the formula in the figure and connect the corresponding resistance in series.

645

646

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220628150112-1.png?width=285&height=241&rev=1.1||alt="image-20220628150112-1.png" height="241" width="285"]]

647

648

(% style="color:red" %)**Note:**If the ADC type sensor needs to be powered by SN50_v3, it is recommended to use +5V to control its switch.Only sensors with low power consumption can be powered with VDD.

649

650

651

==== 2.3.3.5 Digital Interrupt ====

652

653

Digital Interrupt refers to pin PA8, and there are different trigger methods. When there is a trigger, the SN50v3 will send a packet to the server.

654

655

(% style="color:blue" %)**~ Interrupt connection method:**

656

657

[[image:image-20230513105351-5.png||height="147" width="485"]]

658

659

(% style="color:blue" %)**Example to use with door sensor :**

660

661

The door sensor is shown at right. It is a two wire magnetic contact switch used for detecting the open/close status of doors or windows.

662

663

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379210849-860.png?rev=1.1||alt="1656379210849-860.png"]]

664

665

When the two pieces are close to each other, the 2 wire output will be short or open (depending on the type), while if the two pieces are away from each other, the 2 wire output will be the opposite status. So we can use SN50_v3 interrupt interface to detect the status for the door or window.

666

667

(% style="color:blue" %)**~ Below is the installation example:**

668

669

Fix one piece of the magnetic sensor to the door and connect the two pins to SN50_v3 as follows:

670

671

* (((

672

One pin to SN50_v3's PA8 pin

673

)))

674

* (((

675

The other pin to SN50_v3's VDD pin

676

)))

677

678

Install the other piece to the door. Find a place where the two pieces will be close to each other when the door is closed. For this particular magnetic sensor, when the door is closed, the output will be short, and PA8 will be at the VCC voltage.

679

680

Door sensors have two types: ** NC (Normal close)** and **NO (normal open)**. The connection for both type sensors are the same. But the decoding for payload are reverse, user need to modify this in the IoT Server decoder.

681

682

When door sensor is shorted, there will extra power consumption in the circuit, the extra current is 3v3/R14 = 3v3/1Mohm = 3uA which can be ignored.

683

684

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379283019-229.png?rev=1.1||alt="1656379283019-229.png"]]

685

686

The above photos shows the two parts of the magnetic switch fitted to a door.

687

688

The software by default uses the falling edge on the signal line as an interrupt. We need to modify it to accept both the rising edge (0v ~-~-> VCC , door close) and the falling edge (VCC ~-~-> 0v , door open) as the interrupt.

The command is:

(% style="color:blue" %)**AT+INTMOD1=1 ** (%%) ~/~/(more info about INMOD please refer** **[[**AT Command Manual**>>url:http://www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/&file=DRAGINO_LSN50_AT_Commands_v1.5.1.pdf]]**. **)

693

694

Below shows some screen captures in TTN V3:

695

696

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379339508-835.png?rev=1.1||alt="1656379339508-835.png"]]

697

698

In MOD=1, user can use byte 6 to see the status for door open or close. TTN V3 decoder is as below:

699

700

door= (bytes[6] & 0x80)? "CLOSE":"OPEN";

701

702

703

==== 2.3.3.6 I2C Interface (SHT20 & SHT31) ====

704

705

The SDA and SCK are I2C interface lines. You can use these to connect to an I2C device and get the sensor data.

706

707

We have made an example to show how to use the I2C interface to connect to the SHT20/ SHT31 Temperature and Humidity Sensor.

708

709

Notice: Different I2C sensors have different I2C commands set and initiate process, if user want to use other I2C sensors, User need to re-write the source code to support those sensors. SHT20/ SHT31 code in SN50_v3 will be a good reference.

710

711

Below is the connection to SHT20/ SHT31. The connection is as below:

712

713

714

[[image:image-20230513103633-3.png||height="448" width="716"]]

715

716

The device will be able to get the I2C sensor data now and upload to IoT Server.

717

718

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379664142-345.png?rev=1.1||alt="1656379664142-345.png"]]

719

720

Convert the read byte to decimal and divide it by ten.

**Example:**

Temperature: Read:0116(H) = 278(D) Value: 278 /10=27.8℃;

725

726

Humidity: Read:0248(H)=584(D) Value: 584 / 10=58.4, So 58.4%

727

728

If you want to use other I2C device, please refer the SHT20 part source code as reference.

729

730

731

==== 2.3.3.7 Distance Reading ====

732

733

Refer [[Ultrasonic Sensor section>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#H2.4.8UltrasonicSensor]].

734

735

736

==== 2.3.3.8 Ultrasonic Sensor ====

737

738

This Fundamental Principles of this sensor can be found at this link: [[https:~~/~~/wiki.dfrobot.com/Weather_-_proof_Ultrasonic_Sensor_with_Separate_Probe_SKU~~_~~__SEN0208>>url:https://wiki.dfrobot.com/Weather_-_proof_Ultrasonic_Sensor_with_Separate_Probe_SKU___SEN0208]]

739

740

The SN50_v3 detects the pulse width of the sensor and converts it to mm output. The accuracy will be within 1 centimeter. The usable range (the distance between the ultrasonic probe and the measured object) is between 24cm and 600cm.

741

742

The working principle of this sensor is similar to the **HC-SR04** ultrasonic sensor.

743

744

The picture below shows the connection:

745

746

[[image:image-20230512173903-6.png||height="596" width="715"]]

747

748

Connect to the SN50_v3 and run **AT+MOD=2** to switch to ultrasonic mode (ULT).

749

750

The ultrasonic sensor uses the 8^^th^^ and 9^^th^^ byte for the measurement value.

**Example:**

Distance: Read: 0C2D(Hex) = 3117(D) Value: 3117 mm=311.7 cm

==== 2.3.3.9 Battery Output - BAT pin ====

759

760

The BAT pin of SN50v3 is connected to the Battery directly. If users want to use BAT pin to power an external sensor. User need to make sure the external sensor is of low power consumption. Because the BAT pin is always open. If the external sensor is of high power consumption. the battery of SN50v3-LB will run out very soon.

761

762

763

==== 2.3.3.10 +5V Output ====

764

765

SN50v3 will enable +5V output before all sampling and disable the +5v after all sampling.

766

767

The 5V output time can be controlled by AT Command.

768

769

(% style="color:blue" %)**AT+5VT=1000**

770

771

Means set 5V valid time to have 1000ms. So the real 5V output will actually have 1000ms + sampling time for other sensors.

772

773

By default the AT+5VT=500. If the external sensor which require 5v and require more time to get stable state, user can use this command to increase the power ON duration for this sensor.

==== 2.3.3.11 BH1750 Illumination Sensor ====

778

779

MOD=1 support this sensor. The sensor value is in the 8^^th^^ and 9^^th^^ bytes.

780

781

[[image:image-20230512172447-4.png||height="416" width="712"]]

782

783

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220628110012-12.png?rev=1.1||alt="image-20220628110012-12.png" height="361" width="953"]]

784

785

786

==== 2.3.3.12 Working MOD ====

787

788

The working MOD info is contained in the Digital in & Digital Interrupt byte (7^^th^^ Byte).

789

790

User can use the 3^^rd^^ ~~ 7^^th^^ bit of this byte to see the working mod:

791

792

Case 7^^th^^ Byte >> 2 & 0x1f:

* 0: MOD1

* 1: MOD2

* 2: MOD3

* 3: MOD4

* 4: MOD5

* 5: MOD6

* 6: MOD7

* 7: MOD8

* 8: MOD9

== 2.4 Payload Decoder file ==

807

808

809

In TTN, use can add a custom payload so it shows friendly reading

810

811

In the page (% style="color:#037691" %)**Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder**(%%) to add the decoder from:

812

813

[[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/SN50_v3-LB>>https://github.com/dragino/dragino-end-node-decoder/tree/main/SN50_v3-LB]]

== 2.5 Frequency Plans ==

818

819

820

The SN50v3-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.

821

822

[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]

823

824

825

= 3. Configure SN50v3-LB =

826

827

== 3.1 Configure Methods ==

828

829

830

SN50v3-LB supports below configure method:

831

832

* AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].

833

* AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].

834

* LoRaWAN Downlink. Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.

835

836

== 3.2 General Commands ==

837

838

839

These commands are to configure:

840

841

* General system settings like: uplink interval.

842

* LoRaWAN protocol & radio related command.

843

844

They are same for all Dragino Devices which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:

845

846

[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]

847

848

849

== 3.3 Commands special design for SN50v3-LB ==

850

851

852

These commands only valid for S31x-LB, as below:

853

854

855

=== 3.3.1 Set Transmit Interval Time ===

856

857

Feature: Change LoRaWAN End Node Transmit Interval.

858

859

(% style="color:blue" %)**AT Command: AT+TDC**

860

861

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

862

|=(% style="width: 156px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 137px;background-color:#D9E2F3" %)**Function**|=(% style="background-color:#D9E2F3" %)**Response**

863

|(% style="width:156px" %)AT+TDC=?|(% style="width:137px" %)Show current transmit Interval|(((

864

30000

865

OK

866

the interval is 30000ms = 30s

867

)))

868

|(% style="width:156px" %)AT+TDC=60000|(% style="width:137px" %)Set Transmit Interval|(((

869

OK

870

Set transmit interval to 60000ms = 60 seconds

871

)))

872

873

(% style="color:blue" %)**Downlink Command: 0x01**

874

875

Format: Command Code (0x01) followed by 3 bytes time value.

876

877

If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.

878

879

* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds

880

* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds

=== 3.3.2 Get Device Status ===

885

886

Send a LoRaWAN downlink to ask the device to send its status.

887

888

(% style="color:blue" %)**Downlink Payload: **(%%)0x26 01

889

890

Sensor will upload Device Status via FPORT=5. See payload section for detail.

891

892

893

=== 3.3.3 Set Interrupt Mode ===

894

895

Feature, Set Interrupt mode for GPIO_EXIT.

896

897

(% style="color:blue" %)**AT Command: AT+INTMOD1，AT+INTMOD2，AT+INTMOD3**

898

899

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

900

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

901

|(% style="width:154px" %)AT+INTMOD1=?|(% style="width:196px" %)Show current interrupt mode|(% style="width:157px" %)(((

902

0

903

OK

904

the mode is 0 =Disable Interrupt

905

)))

906

|(% style="width:154px" %)AT+INTMOD1=2|(% style="width:196px" %)(((

907

Set Transmit Interval

908

0. (Disable Interrupt),

909

~1. (Trigger by rising and falling edge)

910

2. (Trigger by falling edge)

911

3. (Trigger by rising edge)

912

)))|(% style="width:157px" %)OK

913

|(% style="width:154px" %)AT+INTMOD2=3|(% style="width:196px" %)(((

914

Set Transmit Interval

915

916

trigger by rising edge.

917

)))|(% style="width:157px" %)OK

918

|(% style="width:154px" %)AT+INTMOD3=0|(% style="width:196px" %)Disable Interrupt|(% style="width:157px" %)OK

919

920

(% style="color:blue" %)**Downlink Command: 0x06**

921

922

Format: Command Code (0x06) followed by 3 bytes.

923

924

This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.

925

926

* Example 1: Downlink Payload: 06000000 **~-~-->** AT+INTMOD1=0

927

* Example 2: Downlink Payload: 06000003 **~-~-->** AT+INTMOD1=3

928

* Example 3: Downlink Payload: 06000102 **~-~-->** AT+INTMOD2=2

929

* Example 4: Downlink Payload: 06000201 **~-~-->** AT+INTMOD3=1

=== 3.3.4 Set Power Output Duration ===

934

935

Control the output duration 5V . Before each sampling, device will

936

937

~1. first enable the power output to external sensor,

938

939

2. keep it on as per duration, read sensor value and construct uplink payload

940

941

3. final, close the power output.

942

943

(% style="color:blue" %)**AT Command: AT+5VT**

944

945

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

946

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

947

|(% style="width:154px" %)AT+5VT=?|(% style="width:196px" %)Show 5V open time.|(% style="width:157px" %)(((

500(default)

OK

)))

|(% style="width:154px" %)AT+5VT=1000|(% style="width:196px" %)(((

952

Close after a delay of 1000 milliseconds.

953

)))|(% style="width:157px" %)OK

954

955

(% style="color:blue" %)**Downlink Command: 0x07**

956

957

Format: Command Code (0x07) followed by 2 bytes.

958

959

The first and second bytes are the time to turn on.

960

961

* Example 1: Downlink Payload: 070000 **~-~-->** AT+5VT=0

962

* Example 2: Downlink Payload: 0701F4 **~-~-->** AT+5VT=500

=== 3.3.5 Set Weighing parameters ===

967

968

Feature: Working mode 5 is effective, weight initialization and weight factor setting of HX711.

969

970

(% style="color:blue" %)**AT Command: AT+WEIGRE,AT+WEIGAP**

971

972

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

973

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

974

|(% style="width:154px" %)AT+WEIGRE|(% style="width:196px" %)Weight is initialized to 0.|(% style="width:157px" %)OK

975

|(% style="width:154px" %)AT+WEIGAP=？|(% style="width:196px" %)400.0|(% style="width:157px" %)OK(default)

976

|(% style="width:154px" %)AT+WEIGAP=400.3|(% style="width:196px" %)Set the factor to 400.3.|(% style="width:157px" %)OK

977

978

(% style="color:blue" %)**Downlink Command: 0x08**

979

980

Format: Command Code (0x08) followed by 2 bytes or 4 bytes.

981

982

Use AT+WEIGRE when the first byte is 1, only 1 byte. When it is 2, use AT+WEIGAP, there are 3 bytes.

983

984

The second and third bytes are multiplied by 10 times to be the AT+WEIGAP value.

985

986

* Example 1: Downlink Payload: 0801 **~-~-->** AT+WEIGRE

987

* Example 2: Downlink Payload: 08020FA3 **~-~-->** AT+WEIGAP=400.3

988

* Example 3: Downlink Payload: 08020FA0 **~-~-->** AT+WEIGAP=400.0

=== 3.3.6 Set Digital pulse count value ===

993

994

Feature: Set the pulse count value.

995

996

Count 1 is PA8 pin of mode 6 and mode 9. Count 2 is PA4 pin of mode 9.

997

998

(% style="color:blue" %)**AT Command: AT+SETCNT**

999

1000

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

1001

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

1002

|(% style="width:154px" %)AT+SETCNT=1,100|(% style="width:196px" %)Initialize the count value 1 to 100.|(% style="width:157px" %)OK

1003

|(% style="width:154px" %)AT+SETCNT=2,0|(% style="width:196px" %)Initialize the count value 2 to 0.|(% style="width:157px" %)OK

1004

1005

(% style="color:blue" %)**Downlink Command: 0x09**

1006

1007

Format: Command Code (0x09) followed by 5 bytes.

1008

1009

The first byte is to select which count value to initialize, and the next four bytes are the count value to be initialized.

1010

1011

* Example 1: Downlink Payload: 090100000000 **~-~-->** AT+SETCNT=1,0

1012

* Example 2: Downlink Payload: 0902000003E8 **~-~-->** AT+SETCNT=2,1000

=== 3.3.7 Set Workmode ===

1017

1018

Feature: Switch working mode.

1019

1020

(% style="color:blue" %)**AT Command: AT+MOD**

1021

1022

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

1023

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

1024

|(% style="width:154px" %)AT+MOD=?|(% style="width:196px" %)Get the current working mode.|(% style="width:157px" %)(((

1025

OK

1026

)))

1027

|(% style="width:154px" %)AT+MOD=4|(% style="width:196px" %)Set the working mode to 3DS18B20s.|(% style="width:157px" %)(((

1028

OK

1029

Attention:Take effect after ATZ

1030

)))

1031

1032

(% style="color:blue" %)**Downlink Command: 0x0A**

1033

1034

Format: Command Code (0x0A) followed by 1 bytes.

1035

1036

* Example 1: Downlink Payload: 0A01 **~-~-->** AT+MOD=1

1037

* Example 2: Downlink Payload: 0A04 **~-~-->** AT+MOD=4

= 4. Battery & Power Consumption =

1042

1043

1044

SN50v3-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.

1045

1046

[[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .

1047

1048

1049

= 5. OTA Firmware update =

1050

1051

1052

(% class="wikigeneratedid" %)

1053

User can change firmware SN50v3-LB to:

1054

1055

* Change Frequency band/ region.

1056

* Update with new features.

1057

* Fix bugs.

1058

1059

Firmware and changelog can be downloaded from : **[[Firmware download link>>url:https://www.dropbox.com/sh/kwqv57tp6pejias/AAAopYMATh1GM6fZ-VRCLrpDa?dl=0]]**

1060

1061

1062

Methods to Update Firmware:

1063

1064

* (Recommanded way) OTA firmware update via wireless: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]

1065

* Update through UART TTL interface.**[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.

= 6. FAQ =

== 6.1 Where can i find source code of SN50v3-LB? ==

1070

1071

* **[[Hardware Source Files>>https://github.com/dragino/Lora/tree/master/LSN50/v3.0]].**

1072

* **[[Software Source Code & Compile instruction>>https://github.com/dragino/SN50v3]].**

= 7. Order Info =

Part Number: (% style="color:blue" %)**SN50v3-LB-XX-YY**

1078

1079

(% style="color:red" %)**XX**(%%): The default frequency band

1080

1081

* (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band

1082

* (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band

1083

* (% style="color:red" %)**EU433**(%%): LoRaWAN EU433 band

1084

* (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band

1085

* (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band

1086

* (% style="color:red" %)**US915**(%%): LoRaWAN US915 band

1087

* (% style="color:red" %)**IN865**(%%): LoRaWAN IN865 band

1088

* (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band

1089

1090

(% style="color:red" %)**YY: ** (%%)Hole Option

1091

1092

* (% style="color:red" %)**12**(%%): With M12 waterproof cable hole

1093

* (% style="color:red" %)**16**(%%): With M16 waterproof cable hole

1094

* (% style="color:red" %)**20**(%%): With M20 waterproof cable hole

1095

* (% style="color:red" %)**NH**(%%): No Hole

= 8. Packing Info =

(% style="color:#037691" %)**Package Includes**:

1100

1101

* SN50v3-LB LoRaWAN Generic Node

1102

1103

(% style="color:#037691" %)**Dimension and weight**:

* Device Size: cm

* Device Weight: g

* Package Size / pcs : cm

* Weight / pcs : g

= 9. Support =

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

1114

1115

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.cc>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.cc]]

Wiki source code of SN50v3-LB LoRaWAN Sensor Node User Manual

Applications

Navigation