SN50v3-LB User Manual

(% style="color:blue" %)**SN50V3-LB **(%%)LoRaWAN Sensor Node is a Long Range LoRa Sensor Node. It is designed for outdoor use and powered by (% style="color:blue" %)** 8500mA Li/SOCl2 battery**(%%) for long term use.SN50V3-LB is designed to facilitate developers to quickly deploy industrial level LoRa and IoT solutions. It help users to turn the idea into a practical application and make the Internet of Things a reality. It is easy to program, create and connect your things everywhere.

19

20

21

(% style="color:blue" %)**SN50V3-LB wireless part**(%%) is based on SX1262 allows the user to send data and reach extremely long ranges at low data-rates.It provides ultra-long range spread spectrum communication and high interference immunity whilst minimising current consumption.It targets professional wireless sensor network applications such as irrigation systems, smart metering, smart cities, smartphone detection, building automation, and so on.

22

23

24

(% style="color:blue" %)**SN50V3-LB **(%%)has a powerful 48Mhz ARM microcontroller with 256KB flash and 64KB RAM. It has multiplex I/O pins to connect to different sensors.

25

26

27

(% style="color:blue" %)**SN50V3-LB**(%%) has a built-in BLE module, user can configure the sensor remotely via Mobile Phone. It also support OTA upgrade via private LoRa protocol for easy maintaining.

28

29

30

SN50V3-LB is the 3^^rd^^ generation of LSN50 series generic sensor node from Dragino. It is an (% style="color:blue" %)**open source project**(%%) and has a mature LoRaWAN stack and application software. User can use the pre-load software for their IoT projects or easily customize the software for different requirements.

== 1.2 Features ==

* LoRaWAN 1.0.3 Class A

36

* Ultra-low power consumption

37

* Open-Source hardware/software

38

* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865

39

* Support Bluetooth v5.1 and LoRaWAN remote configure

40

* Support wireless OTA update firmware

41

* Uplink on periodically

42

* Downlink to change configure

43

* 8500mAh Battery for long term use

44

45

== 1.3 Specification ==

46

47

(% style="color:#037691" %)**Common DC Characteristics:**

48

49

* Supply Voltage: built in 8500mAh Li-SOCI2 battery , 2.5v ~~ 3.6v

50

* Operating Temperature: -40 ~~ 85°C

51

52

(% style="color:#037691" %)**I/O Interface:**

53

54

* Battery output (2.6v ~~ 3.6v depends on battery)

55

* +5v controllable output

56

* 3 x Interrupt or Digital IN/OUT pins

57

* 3 x one-wire interfaces

* 1 x UART Interface

* 1 x I2C Interface

(% style="color:#037691" %)**LoRa Spec:**

62

63

* Frequency Range, Band 1 (HF): 862 ~~ 1020 Mhz

64

* Max +22 dBm constant RF output vs.

65

* RX sensitivity: down to -139 dBm.

66

* Excellent blocking immunity

67

68

(% style="color:#037691" %)**Battery:**

69

70

* Li/SOCI2 un-chargeable battery

71

* Capacity: 8500mAh

72

* Self-Discharge: <1% / Year @ 25°C

73

* Max continuously current: 130mA

74

* Max boost current: 2A, 1 second

75

76

(% style="color:#037691" %)**Power Consumption**

77

78

* Sleep Mode: 5uA @ 3.3v

79

* LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm

80

81

== 1.4 Sleep mode and working mode ==

82

83

(% style="color:blue" %)**Deep Sleep Mode: **(%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.

84

85

(% style="color:blue" %)**Working Mode:** (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.

86

87

88

== 1.5 Button & LEDs ==

89

90

91

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675071855856-879.png]]

92

93

94

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

95

|=(% style="width: 167px;background-color:#D9E2F3;color:#0070C0" %)**Behavior on ACT**|=(% style="width: 117px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 225px;background-color:#D9E2F3;color:#0070C0" %)**Action**

96

|(% style="width:167px" %)Pressing ACT between 1s < time < 3s|(% style="width:117px" %)Send an uplink|(% style="width:225px" %)(((

97

If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, (% style="color:blue" %)**blue led** (%%)will blink once.

98

Meanwhile, BLE module will be active and user can connect via BLE to configure device.

99

)))

100

|(% style="width:167px" %)Pressing ACT for more than 3s|(% style="width:117px" %)Active Device|(% style="width:225px" %)(((

101

(% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:#037691" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network.

102

(% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.

103

Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device join or not join LoRaWAN network.

104

)))

105

|(% style="width:167px" %)Fast press ACT 5 times.|(% style="width:117px" %)Deactivate Device|(% style="width:225px" %)(% style="color:red" %)**Red led**(%%) will solid on for 5 seconds. Means device is in Deep Sleep Mode.

106

107

== 1.6 BLE connection ==

108

109

110

SN50v3-LB supports BLE remote configure.

111

112

113

BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:

114

115

* Press button to send an uplink

116

* Press button to active device.

117

* Device Power on or reset.

118

119

If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.

120

121

122

== 1.7 Pin Definitions ==

123

124

125

[[image:image-20230513102034-2.png]]

== 1.8 Mechanical ==

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143884058-338.png]]

132

133

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143899218-599.png]]

134

135

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143909447-639.png]]

== Hole Option ==

SN50v3-LB has different hole size options for different size sensor cable. The options provided are M12, M16 and M20. The definition is as below:

141

142

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220627104757-1.png?rev=1.1||alt="image-20220627104757-1.png"]]

143

144

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656298089706-973.png?rev=1.1||alt="1656298089706-973.png"]]

145

146

147

= 2. Configure SN50v3-LB to connect to LoRaWAN network =

148

149

== 2.1 How it works ==

150

151

152

The SN50v3-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the S31x-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.

153

154

155

== 2.2 Quick guide to connect to LoRaWAN server (OTAA) ==

156

157

158

Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.

159

160

The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.

161

162

163

(% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from SN50v3-LB.

164

165

Each SN50v3-LB is shipped with a sticker with the default device EUI as below:

166

167

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/S31-LB_S31B-LB/WebHome/image-20230426084152-1.png?width=502&height=233&rev=1.1||alt="图片-20230426084152-1.png" height="233" width="502"]]

168

169

170

You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:

171

172

173

(% style="color:blue" %)**Register the device**

174

175

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/1654935135620-998.png?rev=1.1||alt="1654935135620-998.png"]]

176

177

178

(% style="color:blue" %)**Add APP EUI and DEV EUI**

179

180

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-4.png?width=753&height=551&rev=1.1||alt="图片-20220611161308-4.png"]]

181

182

183

(% style="color:blue" %)**Add APP EUI in the application**

184

185

186

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-5.png?width=742&height=601&rev=1.1||alt="图片-20220611161308-5.png"]]

187

188

189

(% style="color:blue" %)**Add APP KEY**

190

191

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-6.png?width=744&height=485&rev=1.1||alt="图片-20220611161308-6.png"]]

192

193

194

(% style="color:blue" %)**Step 2:**(%%) Activate SN50v3-LB

195

196

197

Press the button for 5 seconds to activate the SN50v3-LB.

198

199

(% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:blue" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.

200

201

After join success, it will start to upload messages to TTN and you can see the messages in the panel.

202

203

204

== 2.3 Uplink Payload ==

205

206

=== 2.3.1 Device Status, FPORT~=5 ===

207

208

209

Users can use the downlink command(**0x26 01**) to ask SN50v3 to send device configure detail, include device configure status. SN50v3 will uplink a payload via FPort=5 to server.

210

211

The Payload format is as below.

212

213

214

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

215

|(% colspan="6" style="background-color:#d9e2f3; color:#0070c0" %)**Device Status (FPORT=5)**

Example parse in TTNv3

220

221

222

(% style="color:#037691" %)**Sensor Model**(%%): For SN50v3, this value is 0x1C

223

224

(% style="color:#037691" %)**Firmware Version**(%%): 0x0100, Means: v1.0.0 version

225

226

(% style="color:#037691" %)**Frequency Band**:

*0x01: EU868

*0x02: US915

*0x03: IN865

*0x04: AU915

*0x05: KZ865

*0x06: RU864

*0x07: AS923

*0x08: AS923-1

*0x09: AS923-2

*0x0a: AS923-3

*0x0b: CN470

*0x0c: EU433

*0x0d: KR920

*0x0e: MA869

(% style="color:#037691" %)**Sub-Band**:

258

259

AU915 and US915:value 0x00 ~~ 0x08

260

261

CN470: value 0x0B ~~ 0x0C

262

263

Other Bands: Always 0x00

264

265

266

(% style="color:#037691" %)**Battery Info**:

267

268

Check the battery voltage.

Ex1: 0x0B45 = 2885mV

Ex2: 0x0B49 = 2889mV

=== 2.3.2 Working Modes & Sensor Data. Uplink via FPORT~=2 ===

276

277

278

SN50v3 has different working mode for the connections of different type of sensors. This section describes these modes. Use can use the AT Command AT+MOD to set SN50v3 to different working modes.

For example:

**AT+MOD=2 ** ~/~/ will set the SN50v3 to work in MOD=2 distance mode which target to measure distance via Ultrasonic Sensor.

283

284

285

(% style="color:red" %) **Important Notice:**

286

287

1. Some working modes has payload more than 12 bytes, The US915/AU915/AS923 frequency bands' definition has maximum 11 bytes in **DR0**. Server sides will see NULL payload while SN50v3 transmit in DR0 with 12 bytes payload.

288

1. All modes share the same Payload Explanation from HERE.

289

1. By default, the device will send an uplink message every 20 minutes.

290

291

==== 2.3.2.1 MOD~=1 (Default Mode) ====

292

293

In this mode, uplink payload includes in total 11 bytes. Uplink packets use FPORT=2.

294

295

|**Size(bytes)**|**2**|**2**|**2**|(% style="width:216px" %)**1**|(% style="width:342px" %)**2**|(% style="width:171px" %)**2**

|**Value**|Bat|(((

Temperature(DS18B20)

(PC13)

)))|(((

ADC

(PA4)

)))|(% style="width:216px" %)(((

305

Digital in(PB15) &

306

307

Digital Interrupt(PA8)

308

309

310

)))|(% style="width:342px" %)(((

311

Temperature

312

313

(SHT20 or SHT31 or BH1750 Illumination Sensor)

314

)))|(% style="width:171px" %)(((

Humidity

(SHT20 or SHT31)

)))

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220627150949-6.png?rev=1.1||alt="image-20220627150949-6.png"]]

321

322

323

==== 2.3.2.2 MOD~=2 (Distance Mode) ====

324

325

This mode is target to measure the distance. The payload of this mode is totally 11 bytes. The 8^^th^^ and 9^^th^^ bytes is for the distance.

326

327

|**Size(bytes)**|**2**|**2**|**2**|**1**|**2**|**2**

|**Value**|BAT|(((

Temperature(DS18B20)

(PC13)

)))|(((

ADC

(PA4)

)))|(((

Digital in(PB15) &

Digital Interrupt(PA8)

)))|(((

Distance measure by:

1) LIDAR-Lite V3HP

Or

2) Ultrasonic Sensor

)))|Reserved

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656324539647-568.png?rev=1.1||alt="1656324539647-568.png"]]

348

349

**Connection of LIDAR-Lite V3HP:**

350

351

[[image:image-20230512173758-5.png||height="563" width="712"]]

352

353

**Connection to Ultrasonic Sensor:**

354

355

Need to remove R1 and R2 resistors to get low power,otherwise there will be 240uA standby current.

356

357

[[image:image-20230512173903-6.png||height="596" width="715"]]

358

359

For the connection to TF-Mini or TF-Luna , MOD2 payload is as below:

360

361

|**Size(bytes)**|**2**|**2**|**1**|**2**|**2**|**2**

|**Value**|BAT|(((

Temperature(DS18B20)

(PC13)

)))|(((

Digital in(PB15) &

Digital Interrupt(PA8)

)))|(((

ADC

(PA4)

)))|(((

Distance measure by:1)TF-Mini plus LiDAR

376

Or

377

2) TF-Luna LiDAR

378

)))|Distance signal strength

379

380

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656376779088-686.png?rev=1.1||alt="1656376779088-686.png"]]

381

382

**Connection to [[TF-Mini plus>>url:http://en.benewake.com/product/detail/5c345cd0e5b3a844c472329b.html]] LiDAR(UART version):**

383

384

Need to remove R3 and R4 resistors to get low power,otherwise there will be 400uA standby current.

385

386

[[image:image-20230512180609-7.png||height="555" width="802"]]

387

388

**Connection to [[TF-Luna>>url:http://en.benewake.com/product/detail/5e1c1fd04d839408076b6255.html]] LiDAR (UART version):**

389

390

Need to remove R3 and R4 resistors to get low power,otherwise there will be 400uA standby current.

391

392

[[image:image-20230513105207-4.png||height="469" width="802"]]

393

394

395

==== 2.3.2.3 MOD~=3 (3 ADC + I2C) ====

396

397

This mode has total 12 bytes. Include 3 x ADC + 1x I2C

398

399

(% style="width:1031px" %)

|=(((

**Size(bytes)**

|**Value**|(% style="width:68px" %)(((

ADC1

(PA4)

)))|(% style="width:75px" %)(((

ADC2

(PA5)

)))|(((

ADC3

(PA8)

)))|(((

Digital Interrupt(PB15)

417

)))|(% style="width:304px" %)(((

418

Temperature

419

420

(SHT20 or SHT31 or BH1750 Illumination Sensor)

421

)))|(% style="width:163px" %)(((

Humidity

(SHT20 or SHT31)

)))|(% style="width:53px" %)Bat

426

427

[[image:image-20230513110214-6.png]]

428

429

430

==== 2.3.2.4 MOD~=4 (3 x DS18B20) ====

431

432

433

This mode has total 11 bytes. As shown below:

434

435

(% style="width:1017px" %)

436

437

|**Value**|BAT|(% style="width:186px" %)(((

438

Temperature1(DS18B20)

439

(PC13)

440

)))|(% style="width:82px" %)(((

ADC

(PA4)

)))|(% style="width:210px" %)(((

445

Digital in(PB15) &

446

447

Digital Interrupt(PA8)

448

)))|(% style="width:191px" %)Temperature2(DS18B20)

449

(PB9)|(% style="width:183px" %)Temperature3(DS18B20)

450

(PB8)

451

452

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656377606181-607.png?rev=1.1||alt="1656377606181-607.png"]]

453

454

[[image:image-20230513134006-1.png||height="559" width="736"]]

455

456

457

==== 2.3.2.5 MOD~=5(Weight Measurement by HX711) ====

458

459

[[image:image-20230512164658-2.png||height="532" width="729"]]

460

461

Each HX711 need to be calibrated before used. User need to do below two steps:

462

463

1. Zero calibration. Don't put anything on load cell and run **AT+WEIGRE** to calibrate to Zero gram.

464

1. Adjust calibration factor (default value 400): Put a known weight thing on load cell and run **AT+WEIGAP** to adjust the Calibration Factor.

465

1. (((

466

Weight has 4 bytes, the unit is g.

)))

For example:

**AT+GETSENSORVALUE =0**

472

473

Response: Weight is 401 g

474

475

Check the response of this command and adjust the value to match the real value for thing.

476

477

(% style="width:982px" %)

|=(((

**Size(bytes)**

|**Value**|BAT|(% style="width:282px" %)(((

Temperature(DS18B20)

(PC13)

)))|(% style="width:119px" %)(((

ADC

(PA4)

)))|(% style="width:279px" %)(((

492

Digital in(PB15) &

493

494

Digital Interrupt(PA8)

495

)))|(% style="width:106px" %)Weight

496

497

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220820120036-2.png?width=1003&height=469&rev=1.1||alt="image-20220820120036-2.png" height="469" width="1003"]]

498

499

500

==== 2.3.2.6 MOD~=6 (Counting Mode) ====

501

502

In this mode, the device will work in counting mode. It counts the interrupt on the interrupt pins and sends the count on TDC time.

503

504

Connection is as below. The PIR sensor is a count sensor, it will generate interrupt when people come close or go away. User can replace the PIR sensor with other counting sensors.

505

506

[[image:image-20230512181814-9.png||height="543" width="697"]]

507

508

**Note:** LoRaWAN wireless transmission will infect the PIR sensor. Which cause the counting value increase +1 for every uplink. User can change PIR sensor or put sensor away of the SN50_v3 to avoid this happen.

509

510

(% style="width:961px" %)

511

512

|**Value**|BAT|(% style="width:256px" %)(((

Temperature(DS18B20)

(PC13)

)))|(% style="width:108px" %)(((

ADC

(PA4)

)))|(% style="width:126px" %)(((

Digital in

(PB15)

)))|(% style="width:145px" %)(((

Count

(PA8)

)))

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656378441509-171.png?rev=1.1||alt="1656378441509-171.png"]]

531

532

533

==== 2.3.2.7 MOD~=7 (Three interrupt contact modes) ====

|=(((

**Size(bytes)**

)))|=**2**|=**2**|=**2**|=**1**|=**1**|=1|=2

|**Value**|BAT|(((

Temperature(DS18B20)

(PC13)

)))|(((

ADC

(PA5)

)))|(((

Digital Interrupt1(PA8)

548

)))|Digital Interrupt2(PA4)|Digital Interrupt3(PB15)|Reserved

549

550

[[image:image-20230513111203-7.png||height="324" width="975"]]

551

552

==== 2.3.2.8 MOD~=8 （3ADC+1DS18B20） ====

553

554

(% style="width:917px" %)

|=(((

**Size(bytes)**

|**Value**|BAT|(% style="width:207px" %)(((

Temperature(DS18B20)

(PC13)

)))|(% style="width:94px" %)(((

ADC1

(PA4)

)))|(% style="width:198px" %)(((

567

Digital Interrupt(PB15)

568

)))|(% style="width:84px" %)(((

ADC2

(PA5)

)))|(% style="width:79px" %)(((

ADC3

(PA8)

)))

[[image:image-20230513111231-8.png||height="335" width="900"]]

579

580

581

==== 2.3.2.9 MOD~=9 (3DS18B20+ two Interrupt count mode) ====

582

583

(% style="width:1010px" %)

584

|=(((

585

**Size(bytes)**

586

)))|=**2**|=**2**|=**2**|=**1**|=(% style="width: 193px;" %)**2**|=(% style="width: 78px;" %)4|=(% style="width: 78px;" %)4

587

|**Value**|BAT|(((

588

Temperature1(DS18B20)

(PC13)

)))|(((

Temperature2(DS18B20)

(PB9)

)))|(((

Digital Interrupt

(PB15)

)))|(% style="width:193px" %)(((

600

Temperature3(DS18B20)

601

602

(PB8)

603

)))|(% style="width:78px" %)(((

Count1

(PA8)

)))|(% style="width:78px" %)(((

Count2

(PA4)

)))

[[image:image-20230513111255-9.png||height="341" width="899"]]

614

615

**The newly added AT command is issued correspondingly:**

616

617

**~ AT+INTMOD1** ** PA8** pin： Corresponding downlink: **06 00 00 xx**

618

619

**~ AT+INTMOD2** **PA4** pin： Corresponding downlink:** 06 00 01 xx**

620

621

**~ AT+INTMOD3** **PB15** pin： Corresponding downlink: ** 06 00 02 xx**

**AT+SETCNT=aa,bb**

When AA is 1, set the count of PA8 pin to BB Corresponding downlink：09 01 bb bb bb bb

626

627

When AA is 2, set the count of PA4 pin to BB Corresponding downlink：09 02 bb bb bb bb

=== 2.3.3 Decode payload ===

632

633

While using TTN V3 network, you can add the payload format to decode the payload.

634

635

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656378466788-734.png?rev=1.1||alt="1656378466788-734.png"]]

636

637

The payload decoder function for TTN V3 are here:

638

639

SN50v3 TTN V3 Payload Decoder: [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>url:https://github.com/dragino/dragino-end-node-decoder]]

640

641

642

==== 2.3.3.1 Battery Info ====

643

644

Check the battery voltage for SN50v3.

Ex1: 0x0B45 = 2885mV

Ex2: 0x0B49 = 2889mV

==== 2.3.3.2 Temperature (DS18B20) ====

652

653

If there is a DS18B20 connected to PB3 pin. The temperature will be uploaded in the payload.

654

655

More DS18B20 can check the [[3 DS18B20 mode>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#2.3.4MOD3D4283xDS18B2029]]

**Connection:**

[[image:image-20230512180718-8.png||height="538" width="647"]]

**Example**:

If payload is: 0105H: (0105 & 8000 == 0), temp = 0105H /10 = 26.1 degree

664

665

If payload is: FF3FH : (FF3F & 8000 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.

666

667

（FF3F & 8000：Judge whether the highest bit is 1, when the highest bit is 1, it is negative）

668

669

670

==== 2.3.3.3 Digital Input ====

671

672

The digital input for pin PB15,

673

674

* When PB15 is high, the bit 1 of payload byte 6 is 1.

675

* When PB15 is low, the bit 1 of payload byte 6 is 0.

676

677

(% class="wikigeneratedid" id="H2.3.3.4A0AnalogueDigitalConverter28ADC29" %)

678

(((

679

When the digital interrupt pin is set to AT+INTMODx=0, this pin is used as a digital input pin.

680

681

**Note:**The maximum voltage input supports 3.6V.

682

)))

683

684

==== 2.3.3.4 Analogue Digital Converter (ADC) ====

685

686

The measuring range of the ADC is only about 0V to 1.1V The voltage resolution is about 0.24mv.

687

688

When the measured output voltage of the sensor is not within the range of 0V and 1.1V, the output voltage terminal of the sensor shall be divided The example in the following figure is to reduce the output voltage of the sensor by three times If it is necessary to reduce more times, calculate according to the formula in the figure and connect the corresponding resistance in series.

689

690

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220628150112-1.png?width=285&height=241&rev=1.1||alt="image-20220628150112-1.png" height="241" width="285"]]

691

692

**Note:**If the ADC type sensor needs to be powered by SN50_v3, it is recommended to use +5V to control its switch.Only sensors with low power consumption can be powered with VDD.

693

694

==== 2.3.3.5 Digital Interrupt ====

695

696

Digital Interrupt refers to pin PA8, and there are different trigger methods. When there is a trigger, the SN50v3 will send a packet to the server.

697

698

**~ Interrupt connection method:**

699

700

[[image:image-20230513105351-5.png||height="147" width="485"]]

701

702

**Example to use with door sensor :**

703

704

The door sensor is shown at right. It is a two wire magnetic contact switch used for detecting the open/close status of doors or windows.

705

706

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379210849-860.png?rev=1.1||alt="1656379210849-860.png"]]

707

708

When the two pieces are close to each other, the 2 wire output will be short or open (depending on the type), while if the two pieces are away from each other, the 2 wire output will be the opposite status. So we can use SN50_v3 interrupt interface to detect the status for the door or window.

709

710

**~ Below is the installation example:**

711

712

Fix one piece of the magnetic sensor to the door and connect the two pins to SN50_v3 as follows:

713

714

* (((

715

One pin to SN50_v3's PA8 pin

716

)))

717

* (((

718

The other pin to SN50_v3's VDD pin

719

)))

720

721

Install the other piece to the door. Find a place where the two pieces will be close to each other when the door is closed. For this particular magnetic sensor, when the door is closed, the output will be short, and PA8 will be at the VCC voltage.

722

723

Door sensors have two types: ** NC (Normal close)** and **NO (normal open)**. The connection for both type sensors are the same. But the decoding for payload are reverse, user need to modify this in the IoT Server decoder.

724

725

When door sensor is shorted, there will extra power consumption in the circuit, the extra current is 3v3/R14 = 3v3/1Mohm = 3uA which can be ignored.

726

727

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379283019-229.png?rev=1.1||alt="1656379283019-229.png"]]

728

729

The above photos shows the two parts of the magnetic switch fitted to a door.

730

731

The software by default uses the falling edge on the signal line as an interrupt. We need to modify it to accept both the rising edge (0v ~-~-> VCC , door close) and the falling edge (VCC ~-~-> 0v , door open) as the interrupt.

The command is:

**AT+INTMOD1=1 **~/~/(more info about INMOD please refer** **[[**AT Command Manual**>>url:http://www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/&file=DRAGINO_LSN50_AT_Commands_v1.5.1.pdf]]**. **)

736

737

Below shows some screen captures in TTN V3:

738

739

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379339508-835.png?rev=1.1||alt="1656379339508-835.png"]]

740

741

In MOD=1, user can use byte 6 to see the status for door open or close. TTN V3 decoder is as below:

742

743

door= (bytes[6] & 0x80)? "CLOSE":"OPEN";

744

745

746

==== 2.3.3.6 I2C Interface (SHT20 & SHT31) ====

747

748

The SDA and SCK are I2C interface lines. You can use these to connect to an I2C device and get the sensor data.

749

750

We have made an example to show how to use the I2C interface to connect to the SHT20 Temperature and Humidity Sensor.

751

752

Notice: Different I2C sensors have different I2C commands set and initiate process, if user want to use other I2C sensors, User need to re-write the source code to support those sensors. SHT20 code in SN50_v3 will be a good reference.

753

754

Below is the connection to SHT20/ SHT31. The connection is as below:

755

756

757

[[image:image-20230513103633-3.png||height="636" width="1017"]]

758

759

The device will be able to get the I2C sensor data now and upload to IoT Server.

760

761

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379664142-345.png?rev=1.1||alt="1656379664142-345.png"]]

762

763

Convert the read byte to decimal and divide it by ten.

**Example:**

Temperature: Read:0116(H) = 278(D) Value: 278 /10=27.8℃;

768

769

Humidity: Read:0248(H)=584(D) Value: 584 / 10=58.4, So 58.4%

770

771

If you want to use other I2C device, please refer the SHT20 part source code as reference.

772

773

774

==== 2.3.3.7 Distance Reading ====

775

776

Refer [[Ultrasonic Sensor section>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#H2.4.8UltrasonicSensor]].

777

778

779

==== 2.3.3.8 Ultrasonic Sensor ====

780

781

This Fundamental Principles of this sensor can be found at this link: [[https:~~/~~/wiki.dfrobot.com/Weather_-_proof_Ultrasonic_Sensor_with_Separate_Probe_SKU~~_~~__SEN0208>>url:https://wiki.dfrobot.com/Weather_-_proof_Ultrasonic_Sensor_with_Separate_Probe_SKU___SEN0208]]

782

783

The SN50_v3 detects the pulse width of the sensor and converts it to mm output. The accuracy will be within 1 centimeter. The usable range (the distance between the ultrasonic probe and the measured object) is between 24cm and 600cm.

784

785

The working principle of this sensor is similar to the **HC-SR04** ultrasonic sensor.

786

787

The picture below shows the connection:

788

789

[[image:image-20230512173903-6.png||height="596" width="715"]]

790

791

Connect to the SN50_v3 and run **AT+MOD=2** to switch to ultrasonic mode (ULT).

792

793

The ultrasonic sensor uses the 8^^th^^ and 9^^th^^ byte for the measurement value.

**Example:**

Distance: Read: 0C2D(Hex) = 3117(D) Value: 3117 mm=311.7 cm

==== 2.3.3.9 Battery Output - BAT pin ====

802

803

The BAT pin of SN50v3 is connected to the Battery directly. If users want to use BAT pin to power an external sensor. User need to make sure the external sensor is of low power consumption. Because the BAT pin is always open. If the external sensor is of high power consumption. the battery of SN50v3-LB will run out very soon.

804

805

806

==== 2.3.3.10 +5V Output ====

807

808

SN50v3 will enable +5V output before all sampling and disable the +5v after all sampling.

809

810

The 5V output time can be controlled by AT Command.

**AT+5VT=1000**

Means set 5V valid time to have 1000ms. So the real 5V output will actually have 1000ms + sampling time for other sensors.

815

816

By default the AT+5VT=500. If the external sensor which require 5v and require more time to get stable state, user can use this command to increase the power ON duration for this sensor.

==== 2.3.3.11 BH1750 Illumination Sensor ====

821

822

MOD=1 support this sensor. The sensor value is in the 8^^th^^ and 9^^th^^ bytes.

823

824

[[image:image-20230512172447-4.png||height="593" width="1015"]]

825

826

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220628110012-12.png?rev=1.1||alt="image-20220628110012-12.png"]]

827

828

829

==== 2.3.3.12 Working MOD ====

830

831

The working MOD info is contained in the Digital in & Digital Interrupt byte (7^^th^^ Byte).

832

833

User can use the 3^^rd^^ ~~ 7^^th^^ bit of this byte to see the working mod:

834

835

Case 7^^th^^ Byte >> 2 & 0x1f:

* 0: MOD1

* 1: MOD2

* 2: MOD3

* 3: MOD4

* 4: MOD5

* 5: MOD6

* 6: MOD7

* 7: MOD8

* 8: MOD9

== 2.4 Payload Decoder file ==

848

849

850

In TTN, use can add a custom payload so it shows friendly reading

851

852

In the page (% style="color:#037691" %)**Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder**(%%) to add the decoder from:

853

854

[[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/LSN50v2-S31%26S31B >>https://github.com/dragino/dragino-end-node-decoder/tree/main/LSN50v2-S31%26S31B]]

== 2.5 Frequency Plans ==

859

860

861

The SN50v3-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.

862

863

[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]

864

865

866

= 3. Configure SN50v3-LB =

867

868

== 3.1 Configure Methods ==

869

870

871

SN50v3-LB supports below configure method:

872

873

* AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].

874

* AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].

875

* LoRaWAN Downlink. Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.

876

877

== 3.2 General Commands ==

878

879

880

These commands are to configure:

881

882

* General system settings like: uplink interval.

883

* LoRaWAN protocol & radio related command.

884

885

They are same for all Dragino Devices which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:

886

887

[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]

888

889

890

== 3.3 Commands special design for SN50v3-LB ==

891

892

893

These commands only valid for S31x-LB, as below:

894

895

896

=== 3.3.1 Set Transmit Interval Time ===

897

898

899

Feature: Change LoRaWAN End Node Transmit Interval.

900

901

(% style="color:blue" %)**AT Command: AT+TDC**

902

903

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

904

|=(% style="width: 156px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 137px;background-color:#D9E2F3" %)**Function**|=(% style="background-color:#D9E2F3" %)**Response**

905

|(% style="width:156px" %)AT+TDC=?|(% style="width:137px" %)Show current transmit Interval|(((

906

30000

907

OK

908

the interval is 30000ms = 30s

909

)))

910

|(% style="width:156px" %)AT+TDC=60000|(% style="width:137px" %)Set Transmit Interval|(((

911

OK

912

Set transmit interval to 60000ms = 60 seconds

913

)))

914

915

(% style="color:blue" %)**Downlink Command: 0x01**

916

917

Format: Command Code (0x01) followed by 3 bytes time value.

918

919

If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.

920

921

* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds

922

* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds

923

924

=== 3.3.2 Get Device Status ===

925

926

Send a LoRaWAN downlink to ask device send Alarm settings.

927

928

(% style="color:blue" %)**Downlink Payload: **(%%)0x26 01

929

930

Sensor will upload Device Status via FPORT=5. See payload section for detail.

931

932

933

=== 3.3.3 Set Interrupt Mode ===

934

935

936

Feature, Set Interrupt mode for GPIO_EXIT.

937

938

(% style="color:blue" %)**AT Command: AT+INTMOD1，AT+INTMOD2，AT+INTMOD3**

939

940

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

941

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

942

|(% style="width:154px" %)AT+INTMOD1=?|(% style="width:196px" %)Show current interrupt mode|(% style="width:157px" %)(((

943

0

944

OK

945

the mode is 0 =Disable Interrupt

946

)))

947

|(% style="width:154px" %)AT+INTMOD1=2|(% style="width:196px" %)(((

948

Set Transmit Interval

949

0. (Disable Interrupt),

950

~1. (Trigger by rising and falling edge)

951

2. (Trigger by falling edge)

952

3. (Trigger by rising edge)

953

)))|(% style="width:157px" %)OK

954

|(% style="width:154px" %)AT+INTMOD2=3|(% style="width:196px" %)(((

955

Set Transmit Interval

956

957

trigger by rising edge.

958

)))|(% style="width:157px" %)OK

959

|(% style="width:154px" %)AT+INTMOD3=0|(% style="width:196px" %)Disable Interrupt|(% style="width:157px" %)OK

960

961

(% style="color:blue" %)**Downlink Command: 0x06**

962

963

Format: Command Code (0x06) followed by 3 bytes.

964

965

This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.

966

967

* Example 1: Downlink Payload: 06000000 **~-~-->** AT+INTMOD1=0

968

* Example 2: Downlink Payload: 06000003 **~-~-->** AT+INTMOD1=3

969

* Example 3: Downlink Payload: 06000102 **~-~-->** AT+INTMOD2=2

970

* Example 4: Downlink Payload: 06000201 **~-~-->** AT+INTMOD3=1

971

972

=== 3.3.4 Set Power Output Duration ===

973

974

Control the output duration 5V . Before each sampling, device will

975

976

~1. first enable the power output to external sensor,

977

978

2. keep it on as per duration, read sensor value and construct uplink payload

979

980

3. final, close the power output.

981

982

(% style="color:blue" %)**AT Command: AT+5VT**

983

984

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

985

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

986

|(% style="width:154px" %)AT+5VT=?|(% style="width:196px" %)Show 5V open time.|(% style="width:157px" %)(((

500(default)

OK

)))

|(% style="width:154px" %)AT+5VT=1000|(% style="width:196px" %)(((

992

Close after a delay of 1000 milliseconds.

993

)))|(% style="width:157px" %)OK

994

995

(% style="color:blue" %)**Downlink Command: 0x07**

996

997

Format: Command Code (0x07) followed by 2 bytes.

998

999

The first and second bytes are the time to turn on.

1000

1001

* Example 1: Downlink Payload: 070000 **~-~-->** AT+5VT=0

1002

* Example 2: Downlink Payload: 0701F4 **~-~-->** AT+5VT=500

1003

1004

=== 3.3.5 Set Weighing parameters ===

1005

1006

Feature: Working mode 5 is effective, weight initialization and weight factor setting of HX711.

1007

1008

(% style="color:blue" %)**AT Command: AT+WEIGRE,AT+WEIGAP**

1009

1010

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

1011

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

1012

|(% style="width:154px" %)AT+WEIGRE|(% style="width:196px" %)Weight is initialized to 0.|(% style="width:157px" %)OK

1013

|(% style="width:154px" %)AT+WEIGAP=？|(% style="width:196px" %)400.0|(% style="width:157px" %)OK(default)

1014

|(% style="width:154px" %)AT+WEIGAP=400.3|(% style="width:196px" %)Set the factor to 400.3.|(% style="width:157px" %)OK

1015

1016

(% style="color:blue" %)**Downlink Command: 0x08**

1017

1018

1019

Format: Command Code (0x08) followed by 2 bytes or 4 bytes.

1020

1021

Use AT+WEIGRE when the first byte is 1, only 1 byte. When it is 2, use AT+WEIGAP, there are 3 bytes.

1022

1023

The second and third bytes are multiplied by 10 times to be the AT+WEIGAP value.

1024

1025

* Example 1: Downlink Payload: 0801 **~-~-->** AT+WEIGRE

1026

* Example 2: Downlink Payload: 08020FA3 **~-~-->** AT+WEIGAP=400.3

1027

* Example 3: Downlink Payload: 08020FA0 **~-~-->** AT+WEIGAP=400.0

1028

1029

=== 3.3.6 Set Digital pulse count value ===

1030

1031

Feature: Set the pulse count value.

1032

1033

Count 1 is PA8 pin of mode 6 and mode 9. Count 2 is PA4 pin of mode 9.

1034

1035

(% style="color:blue" %)**AT Command: AT+SETCNT**

1036

1037

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

1038

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

1039

|(% style="width:154px" %)AT+SETCNT=1,100|(% style="width:196px" %)Initialize the count value 1 to 100.|(% style="width:157px" %)OK

1040

|(% style="width:154px" %)AT+SETCNT=2,0|(% style="width:196px" %)Initialize the count value 2 to 0.|(% style="width:157px" %)OK

1041

1042

(% style="color:blue" %)**Downlink Command: 0x09**

1043

1044

1045

Format: Command Code (0x09) followed by 5 bytes.

1046

1047

The first byte is to select which count value to initialize, and the next four bytes are the count value to be initialized.

1048

1049

* Example 1: Downlink Payload: 090100000000 **~-~-->** AT+SETCNT=1,0

1050

* Example 2: Downlink Payload: 0902000003E8 **~-~-->** AT+SETCNT=2,1000

1051

1052

=== 3.3.7 Set Workmode ===

1053

1054

Feature: Switch working mode.

1055

1056

(% style="color:blue" %)**AT Command: AT+MOD**

1057

1058

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

1059

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

1060

|(% style="width:154px" %)AT+MOD=?|(% style="width:196px" %)Get the current working mode.|(% style="width:157px" %)(((

1061

OK

1062

)))

1063

|(% style="width:154px" %)AT+MOD=4|(% style="width:196px" %)Set the working mode to 3DS18B20s.|(% style="width:157px" %)(((

1064

OK

1065

1066

Attention:Take effect after ATZ

1067

)))

1068

1069

(% style="color:blue" %)**Downlink Command: 0x0A**

1070

1071

1072

Format: Command Code (0x0A) followed by 1 bytes.

1073

1074

* Example 1: Downlink Payload: 0A01 **~-~-->** AT+MOD=1

1075

* Example 2: Downlink Payload: 0A04 **~-~-->** AT+MOD=4

1076

1077

= 4. Battery & Power Consumption =

1078

1079

1080

SN50v3-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.

1081

1082

[[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .

1083

1084

1085

= 5. OTA Firmware update =

1086

1087

1088

(% class="wikigeneratedid" %)

1089

User can change firmware SN50v3-LB to:

1090

1091

* Change Frequency band/ region.

1092

* Update with new features.

1093

* Fix bugs.

1094

1095

Firmware and changelog can be downloaded from : **[[Firmware download link>>url:https://www.dropbox.com/sh/kwqv57tp6pejias/AAAopYMATh1GM6fZ-VRCLrpDa?dl=0]]**

1096

1097

1098

Methods to Update Firmware:

1099

1100

* (Recommanded way) OTA firmware update via wireless: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]

1101

* Update through UART TTL interface.**[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.

= 6. FAQ =

== 6.1 Where can i find source code of SN50v3-LB? ==

1106

1107

* **[[Hardware Source Files>>https://github.com/dragino/Lora/tree/master/LSN50/v3.0]].**

1108

* **[[Software Source Code & Compile instruction>>https://github.com/dragino/SN50v3]].**

= 7. Order Info =

Part Number: (% style="color:blue" %)**SN50v3-LB-XX-YY**

1114

1115

(% style="color:red" %)**XX**(%%): The default frequency band

1116

1117

* (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band

1118

* (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band

1119

* (% style="color:red" %)**EU433**(%%): LoRaWAN EU433 band

1120

* (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band

1121

* (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band

1122

* (% style="color:red" %)**US915**(%%): LoRaWAN US915 band

1123

* (% style="color:red" %)**IN865**(%%): LoRaWAN IN865 band

1124

* (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band

1125

1126

(% style="color:red" %)**YY: ** (%%)Hole Option

1127

1128

* (% style="color:red" %)**12**(%%): With M12 waterproof cable hole

1129

* (% style="color:red" %)**16**(%%): With M16 waterproof cable hole

1130

* (% style="color:red" %)**20**(%%): With M20 waterproof cable hole

1131

* (% style="color:red" %)**NH**(%%): No Hole

= 8. Packing Info =

(% style="color:#037691" %)**Package Includes**:

1136

1137

* SN50v3-LB LoRaWAN Generic Node

1138

1139

(% style="color:#037691" %)**Dimension and weight**:

* Device Size: cm

* Device Weight: g

* Package Size / pcs : cm

* Weight / pcs : g

= 9. Support =

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

1150

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]

Wiki source code of SN50v3-LB User Manual

Applications

Navigation