SN50v3-LB User Manual

(% style="color:blue" %)**SN50V3-LB **(%%)LoRaWAN Sensor Node is a Long Range LoRa Sensor Node. It is designed for outdoor use and powered by (% style="color:blue" %)** 8500mA Li/SOCl2 battery**(%%) for long term use.SN50V3-LB is designed to facilitate developers to quickly deploy industrial level LoRa and IoT solutions. It help users to turn the idea into a practical application and make the Internet of Things a reality. It is easy to program, create and connect your things everywhere.

19

20

21

(% style="color:blue" %)**SN50V3-LB wireless part**(%%) is based on SX1262 allows the user to send data and reach extremely long ranges at low data-rates.It provides ultra-long range spread spectrum communication and high interference immunity whilst minimising current consumption.It targets professional wireless sensor network applications such as irrigation systems, smart metering, smart cities, smartphone detection, building automation, and so on.

22

23

24

(% style="color:blue" %)**SN50V3-LB **(%%)has a powerful 48Mhz ARM microcontroller with 256KB flash and 64KB RAM. It has multiplex I/O pins to connect to different sensors.

25

26

27

(% style="color:blue" %)**SN50V3-LB**(%%) has a built-in BLE module, user can configure the sensor remotely via Mobile Phone. It also support OTA upgrade via private LoRa protocol for easy maintaining.

28

29

30

SN50V3-LB is the 3^^rd^^ generation of LSN50 series generic sensor node from Dragino. It is an (% style="color:blue" %)**open source project**(%%) and has a mature LoRaWAN stack and application software. User can use the pre-load software for their IoT projects or easily customize the software for different requirements.

== 1.2 Features ==

* LoRaWAN 1.0.3 Class A

36

* Ultra-low power consumption

37

* Open-Source hardware/software

38

* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865

39

* Support Bluetooth v5.1 and LoRaWAN remote configure

40

* Support wireless OTA update firmware

41

* Uplink on periodically

42

* Downlink to change configure

43

* 8500mAh Battery for long term use

44

45

== 1.3 Specification ==

46

47

(% style="color:#037691" %)**Common DC Characteristics:**

48

49

* Supply Voltage: built in 8500mAh Li-SOCI2 battery , 2.5v ~~ 3.6v

50

* Operating Temperature: -40 ~~ 85°C

51

52

(% style="color:#037691" %)**I/O Interface:**

53

54

* Battery output (2.6v ~~ 3.6v depends on battery)

55

* +5v controllable output

56

* 3 x Interrupt or Digital IN/OUT pins

57

* 3 x one-wire interfaces

* 1 x UART Interface

* 1 x I2C Interface

(% style="color:#037691" %)**LoRa Spec:**

62

63

* Frequency Range, Band 1 (HF): 862 ~~ 1020 Mhz

64

* Max +22 dBm constant RF output vs.

65

* RX sensitivity: down to -139 dBm.

66

* Excellent blocking immunity

67

68

(% style="color:#037691" %)**Battery:**

69

70

* Li/SOCI2 un-chargeable battery

71

* Capacity: 8500mAh

72

* Self-Discharge: <1% / Year @ 25°C

73

* Max continuously current: 130mA

74

* Max boost current: 2A, 1 second

75

76

(% style="color:#037691" %)**Power Consumption**

77

78

* Sleep Mode: 5uA @ 3.3v

79

* LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm

80

81

== 1.4 Sleep mode and working mode ==

82

83

(% style="color:blue" %)**Deep Sleep Mode: **(%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.

84

85

(% style="color:blue" %)**Working Mode:** (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.

86

87

88

== 1.5 Button & LEDs ==

89

90

91

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675071855856-879.png]]

92

93

94

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

95

|=(% style="width: 167px;background-color:#D9E2F3;color:#0070C0" %)**Behavior on ACT**|=(% style="width: 117px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 225px;background-color:#D9E2F3;color:#0070C0" %)**Action**

96

|(% style="width:167px" %)Pressing ACT between 1s < time < 3s|(% style="width:117px" %)Send an uplink|(% style="width:225px" %)(((

97

If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, (% style="color:blue" %)**blue led** (%%)will blink once.

98

Meanwhile, BLE module will be active and user can connect via BLE to configure device.

99

)))

100

|(% style="width:167px" %)Pressing ACT for more than 3s|(% style="width:117px" %)Active Device|(% style="width:225px" %)(((

101

(% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:#037691" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network.

102

(% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.

103

Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device join or not join LoRaWAN network.

104

)))

105

|(% style="width:167px" %)Fast press ACT 5 times.|(% style="width:117px" %)Deactivate Device|(% style="width:225px" %)(% style="color:red" %)**Red led**(%%) will solid on for 5 seconds. Means device is in Deep Sleep Mode.

106

107

== 1.6 BLE connection ==

108

109

110

SN50v3-LB supports BLE remote configure.

111

112

113

BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:

114

115

* Press button to send an uplink

116

* Press button to active device.

117

* Device Power on or reset.

118

119

If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.

120

121

122

== 1.7 Pin Definitions ==

123

124

125

[[image:image-20230513102034-2.png]]

== 1.8 Mechanical ==

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143884058-338.png]]

132

133

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143899218-599.png]]

134

135

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143909447-639.png]]

== Hole Option ==

SN50v3-LB has different hole size options for different size sensor cable. The options provided are M12, M16 and M20. The definition is as below:

141

142

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220627104757-1.png?rev=1.1||alt="image-20220627104757-1.png"]]

143

144

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656298089706-973.png?rev=1.1||alt="1656298089706-973.png"]]

145

146

147

= 2. Configure SN50v3-LB to connect to LoRaWAN network =

148

149

== 2.1 How it works ==

150

151

152

The SN50v3-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the S31x-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.

153

154

155

== 2.2 Quick guide to connect to LoRaWAN server (OTAA) ==

156

157

158

Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.

159

160

The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.

161

162

163

(% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from SN50v3-LB.

164

165

Each SN50v3-LB is shipped with a sticker with the default device EUI as below:

166

167

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/S31-LB_S31B-LB/WebHome/image-20230426084152-1.png?width=502&height=233&rev=1.1||alt="图片-20230426084152-1.png" height="233" width="502"]]

168

169

170

You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:

171

172

173

(% style="color:blue" %)**Register the device**

174

175

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/1654935135620-998.png?rev=1.1||alt="1654935135620-998.png"]]

176

177

178

(% style="color:blue" %)**Add APP EUI and DEV EUI**

179

180

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-4.png?width=753&height=551&rev=1.1||alt="图片-20220611161308-4.png"]]

181

182

183

(% style="color:blue" %)**Add APP EUI in the application**

184

185

186

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-5.png?width=742&height=601&rev=1.1||alt="图片-20220611161308-5.png"]]

187

188

189

(% style="color:blue" %)**Add APP KEY**

190

191

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-6.png?width=744&height=485&rev=1.1||alt="图片-20220611161308-6.png"]]

192

193

194

(% style="color:blue" %)**Step 2:**(%%) Activate SN50v3-LB

195

196

197

Press the button for 5 seconds to activate the SN50v3-LB.

198

199

(% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:blue" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.

200

201

After join success, it will start to upload messages to TTN and you can see the messages in the panel.

202

203

204

== 2.3 Uplink Payload ==

205

206

=== 2.3.1 Device Status, FPORT~=5 ===

207

208

209

Users can use the downlink command(**0x26 01**) to ask SN50v3 to send device configure detail, include device configure status. SN50v3 will uplink a payload via FPort=5 to server.

210

211

The Payload format is as below.

212

213

214

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

215

|(% colspan="6" style="background-color:#d9e2f3; color:#0070c0" %)**Device Status (FPORT=5)**

Example parse in TTNv3

220

221

222

(% style="color:#037691" %)**Sensor Model**(%%): For SN50v3, this value is 0x1C

223

224

(% style="color:#037691" %)**Firmware Version**(%%): 0x0100, Means: v1.0.0 version

225

226

(% style="color:#037691" %)**Frequency Band**:

*0x01: EU868

*0x02: US915

*0x03: IN865

*0x04: AU915

*0x05: KZ865

*0x06: RU864

*0x07: AS923

*0x08: AS923-1

*0x09: AS923-2

*0x0a: AS923-3

*0x0b: CN470

*0x0c: EU433

*0x0d: KR920

*0x0e: MA869

(% style="color:#037691" %)**Sub-Band**:

258

259

AU915 and US915:value 0x00 ~~ 0x08

260

261

CN470: value 0x0B ~~ 0x0C

262

263

Other Bands: Always 0x00

264

265

266

(% style="color:#037691" %)**Battery Info**:

267

268

Check the battery voltage.

Ex1: 0x0B45 = 2885mV

Ex2: 0x0B49 = 2889mV

=== 2.3.2 Working Modes & Sensor Data. Uplink via FPORT~=2 ===

276

277

278

SN50v3 has different working mode for the connections of different type of sensors. This section describes these modes. Use can use the AT Command AT+MOD to set SN50v3 to different working modes.

For example:

**AT+MOD=2 ** ~/~/ will set the SN50v3 to work in MOD=2 distance mode which target to measure distance via Ultrasonic Sensor.

283

284

285

(% style="color:red" %) **Important Notice:**

286

287

1. Some working modes has payload more than 12 bytes, The US915/AU915/AS923 frequency bands' definition has maximum 11 bytes in **DR0**. Server sides will see NULL payload while SN50v3 transmit in DR0 with 12 bytes payload.

288

1. All modes share the same Payload Explanation from HERE.

289

1. By default, the device will send an uplink message every 20 minutes.

290

291

==== 2.3.2.1 MOD~=1 (Default Mode) ====

292

293

In this mode, uplink payload includes in total 11 bytes. Uplink packets use FPORT=2.

294

295

|**Size(bytes)**|**2**|**2**|**2**|(% style="width:216px" %)**1**|(% style="width:342px" %)**2**|(% style="width:171px" %)**2**

|**Value**|Bat|(((

Temperature(DS18B20)

(PC13)

)))|(((

ADC

(PA4)

)))|(% style="width:216px" %)(((

305

Digital in(PB15) &

306

307

Digital Interrupt(PA8)

308

309

310

)))|(% style="width:342px" %)(((

311

Temperature

312

313

(SHT20 or SHT31 or BH1750 Illumination Sensor)

314

)))|(% style="width:171px" %)(((

Humidity

(SHT20 or SHT31)

)))

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220627150949-6.png?rev=1.1||alt="image-20220627150949-6.png"]]

321

322

323

==== 2.3.2.2 MOD~=2 (Distance Mode) ====

324

325

This mode is target to measure the distance. The payload of this mode is totally 11 bytes. The 8^^th^^ and 9^^th^^ bytes is for the distance.

326

327

|**Size(bytes)**|**2**|**2**|**2**|**1**|**2**|**2**

|**Value**|BAT|(((

Temperature(DS18B20)

(PC13)

)))|(((

ADC

(PA4)

)))|(((

Digital in(PB15) &

Digital Interrupt(PA8)

)))|(((

Distance measure by:

1) LIDAR-Lite V3HP

Or

2) Ultrasonic Sensor

)))|Reserved

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656324539647-568.png?rev=1.1||alt="1656324539647-568.png"]]

348

349

**Connection of LIDAR-Lite V3HP:**

350

351

[[image:image-20230512173758-5.png||height="563" width="712"]]

352

353

**Connection to Ultrasonic Sensor:**

354

355

Need to remove R1 and R2 resistors to get low power,otherwise there will be 240uA standby current.

356

357

[[image:image-20230512173903-6.png||height="596" width="715"]]

358

359

For the connection to TF-Mini or TF-Luna , MOD2 payload is as below:

360

361

|**Size(bytes)**|**2**|**2**|**1**|**2**|**2**|**2**

|**Value**|BAT|(((

Temperature(DS18B20)

(PC13)

)))|(((

Digital in(PB15) &

Digital Interrupt(PA8)

)))|(((

ADC

(PA4)

)))|(((

Distance measure by:1)TF-Mini plus LiDAR

376

Or

377

2) TF-Luna LiDAR

378

)))|Distance signal strength

379

380

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656376779088-686.png?rev=1.1||alt="1656376779088-686.png"]]

381

382

**Connection to [[TF-Mini plus>>url:http://en.benewake.com/product/detail/5c345cd0e5b3a844c472329b.html]] LiDAR(UART version):**

383

384

Need to remove R3 and R4 resistors to get low power,otherwise there will be 400uA standby current.

385

386

[[image:image-20230512180609-7.png||height="555" width="802"]]

387

388

**Connection to [[TF-Luna>>url:http://en.benewake.com/product/detail/5e1c1fd04d839408076b6255.html]] LiDAR (UART version):**

389

390

Need to remove R3 and R4 resistors to get low power,otherwise there will be 400uA standby current.

391

392

[[image:image-20230513105207-4.png||height="469" width="802"]]

393

394

395

==== 2.3.2.3 MOD~=3 (3 ADC + I2C) ====

396

397

This mode has total 12 bytes. Include 3 x ADC + 1x I2C

398

399

(% style="width:1031px" %)

|=(((

**Size(bytes)**

|**Value**|(% style="width:68px" %)(((

ADC1

(PA4)

)))|(% style="width:75px" %)(((

ADC2

(PA5)

)))|(((

ADC3

(PA8)

)))|(((

Digital Interrupt(PB15)

417

)))|(% style="width:304px" %)(((

418

Temperature

419

420

(SHT20 or SHT31 or BH1750 Illumination Sensor)

421

)))|(% style="width:163px" %)(((

Humidity

(SHT20 or SHT31)

)))|(% style="width:53px" %)Bat

426

427

[[image:image-20230513110214-6.png]]

428

429

430

==== 2.3.2.4 MOD~=4 (3 x DS18B20) ====

431

432

[[image:image-20230512170701-3.png||height="565" width="743"]]

433

434

This mode has total 11 bytes. As shown below:

435

436

(% style="width:1017px" %)

437

438

|**Value**|BAT|(% style="width:186px" %)(((

439

Temperature1(DS18B20)

440

(PC13)

441

)))|(% style="width:82px" %)(((

ADC

(PA4)

)))|(% style="width:210px" %)(((

446

Digital in(PB15) &

447

448

Digital Interrupt(PA8)

449

)))|(% style="width:191px" %)Temperature2(DS18B20)

450

(PB9)|(% style="width:183px" %)Temperature3(DS18B20)

451

(PB8)

452

453

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656377606181-607.png?rev=1.1||alt="1656377606181-607.png"]]

454

455

456

==== 2.3.2.5 MOD~=5(Weight Measurement by HX711) ====

457

458

[[image:image-20230512164658-2.png||height="532" width="729"]]

459

460

Each HX711 need to be calibrated before used. User need to do below two steps:

461

462

1. Zero calibration. Don't put anything on load cell and run **AT+WEIGRE** to calibrate to Zero gram.

463

1. Adjust calibration factor (default value 400): Put a known weight thing on load cell and run **AT+WEIGAP** to adjust the Calibration Factor.

464

1. (((

465

Weight has 4 bytes, the unit is g.

)))

For example:

**AT+GETSENSORVALUE =0**

471

472

Response: Weight is 401 g

473

474

Check the response of this command and adjust the value to match the real value for thing.

475

476

(% style="width:982px" %)

|=(((

**Size(bytes)**

|**Value**|BAT|(% style="width:282px" %)(((

Temperature(DS18B20)

(PC13)

)))|(% style="width:119px" %)(((

ADC

(PA4)

)))|(% style="width:279px" %)(((

491

Digital in(PB15) &

492

493

Digital Interrupt(PA8)

494

)))|(% style="width:106px" %)Weight

495

496

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220820120036-2.png?width=1003&height=469&rev=1.1||alt="image-20220820120036-2.png" height="469" width="1003"]]

497

498

499

==== 2.3.2.6 MOD~=6 (Counting Mode) ====

500

501

In this mode, the device will work in counting mode. It counts the interrupt on the interrupt pins and sends the count on TDC time.

502

503

Connection is as below. The PIR sensor is a count sensor, it will generate interrupt when people come close or go away. User can replace the PIR sensor with other counting sensors.

504

505

[[image:image-20230512181814-9.png||height="543" width="697"]]

506

507

**Note:** LoRaWAN wireless transmission will infect the PIR sensor. Which cause the counting value increase +1 for every uplink. User can change PIR sensor or put sensor away of the SN50_v3 to avoid this happen.

508

509

(% style="width:961px" %)

510

511

|**Value**|BAT|(% style="width:256px" %)(((

Temperature(DS18B20)

(PC13)

)))|(% style="width:108px" %)(((

ADC

(PA4)

)))|(% style="width:126px" %)(((

Digital in

(PB15)

)))|(% style="width:145px" %)(((

Count

(PA8)

)))

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656378441509-171.png?rev=1.1||alt="1656378441509-171.png"]]

530

531

532

==== 2.3.2.7 MOD~=7 (Three interrupt contact modes) ====

|=(((

**Size(bytes)**

)))|=**2**|=**2**|=**2**|=**1**|=**1**|=1|=2

|**Value**|BAT|(((

Temperature(DS18B20)

(PC13)

)))|(((

ADC

(PA5)

)))|(((

Digital Interrupt1(PA8)

547

)))|Digital Interrupt2(PA4)|Digital Interrupt3(PB15)|Reserved

548

549

[[image:image-20230513111203-7.png||height="324" width="975"]]

550

551

==== 2.3.2.8 MOD~=8 （3ADC+1DS18B20） ====

552

553

(% style="width:917px" %)

|=(((

**Size(bytes)**

|**Value**|BAT|(% style="width:207px" %)(((

Temperature(DS18B20)

(PC13)

)))|(% style="width:94px" %)(((

ADC1

(PA4)

)))|(% style="width:198px" %)(((

566

Digital Interrupt(PB15)

567

)))|(% style="width:84px" %)(((

ADC2

(PA5)

)))|(% style="width:79px" %)(((

ADC3

(PA8)

)))

[[image:image-20230513111231-8.png||height="335" width="900"]]

578

579

580

==== 2.3.2.9 MOD~=9 (3DS18B20+ two Interrupt count mode) ====

581

582

(% style="width:1010px" %)

583

|=(((

584

**Size(bytes)**

585

)))|=**2**|=**2**|=**2**|=**1**|=(% style="width: 193px;" %)**2**|=(% style="width: 78px;" %)4|=(% style="width: 78px;" %)4

586

|**Value**|BAT|(((

587

Temperature1(DS18B20)

(PC13)

)))|(((

Temperature2(DS18B20)

(PB9)

)))|(((

Digital Interrupt

(PB15)

)))|(% style="width:193px" %)(((

599

Temperature3(DS18B20)

600

601

(PB8)

602

)))|(% style="width:78px" %)(((

Count1

(PA8)

)))|(% style="width:78px" %)(((

Count2

(PA4)

)))

[[image:image-20230513111255-9.png||height="341" width="899"]]

613

614

**The newly added AT command is issued correspondingly:**

615

616

**~ AT+INTMOD1** ** PA8** pin： Corresponding downlink: **06 00 00 xx**

617

618

**~ AT+INTMOD2** **PA4** pin： Corresponding downlink:** 06 00 01 xx**

619

620

**~ AT+INTMOD3** **PB15** pin： Corresponding downlink: ** 06 00 02 xx**

**AT+SETCNT=aa,bb**

When AA is 1, set the count of PA8 pin to BB Corresponding downlink：09 01 bb bb bb bb

625

626

When AA is 2, set the count of PA4 pin to BB Corresponding downlink：09 02 bb bb bb bb

=== 2.3.3 Decode payload ===

631

632

While using TTN V3 network, you can add the payload format to decode the payload.

633

634

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656378466788-734.png?rev=1.1||alt="1656378466788-734.png"]]

635

636

The payload decoder function for TTN V3 are here:

637

638

SN50v3 TTN V3 Payload Decoder: [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>url:https://github.com/dragino/dragino-end-node-decoder]]

639

640

641

==== 2.3.3.1 Battery Info ====

642

643

Check the battery voltage for SN50v3.

Ex1: 0x0B45 = 2885mV

Ex2: 0x0B49 = 2889mV

==== 2.3.3.2 Temperature (DS18B20) ====

651

652

If there is a DS18B20 connected to PB3 pin. The temperature will be uploaded in the payload.

653

654

More DS18B20 can check the [[3 DS18B20 mode>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#2.3.4MOD3D4283xDS18B2029]]

**Connection:**

[[image:image-20230512180718-8.png||height="538" width="647"]]

**Example**:

If payload is: 0105H: (0105 & 8000 == 0), temp = 0105H /10 = 26.1 degree

663

664

If payload is: FF3FH : (FF3F & 8000 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.

665

666

（FF3F & 8000：Judge whether the highest bit is 1, when the highest bit is 1, it is negative）

667

668

669

==== 2.3.3.3 Digital Input ====

670

671

The digital input for pin PB15,

672

673

* When PB15 is high, the bit 1 of payload byte 6 is 1.

674

* When PB15 is low, the bit 1 of payload byte 6 is 0.

675

676

(% class="wikigeneratedid" id="H2.3.3.4A0AnalogueDigitalConverter28ADC29" %)

677

(((

678

When the digital interrupt pin is set to AT+INTMODx=0, this pin is used as a digital input pin.

679

680

**Note:**The maximum voltage input supports 3.6V.

681

)))

682

683

==== 2.3.3.4 Analogue Digital Converter (ADC) ====

684

685

The measuring range of the ADC is only about 0V to 1.1V The voltage resolution is about 0.24mv.

686

687

When the measured output voltage of the sensor is not within the range of 0V and 1.1V, the output voltage terminal of the sensor shall be divided The example in the following figure is to reduce the output voltage of the sensor by three times If it is necessary to reduce more times, calculate according to the formula in the figure and connect the corresponding resistance in series.

688

689

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220628150112-1.png?width=285&height=241&rev=1.1||alt="image-20220628150112-1.png" height="241" width="285"]]

690

691

**Note:**If the ADC type sensor needs to be powered by SN50_v3, it is recommended to use +5V to control its switch.Only sensors with low power consumption can be powered with VDD.

692

693

==== 2.3.3.5 Digital Interrupt ====

694

695

Digital Interrupt refers to pin PA8, and there are different trigger methods. When there is a trigger, the SN50v3 will send a packet to the server.

696

697

**~ Interrupt connection method:**

698

699

[[image:image-20230513105351-5.png||height="147" width="485"]]

700

701

**Example to use with door sensor :**

702

703

The door sensor is shown at right. It is a two wire magnetic contact switch used for detecting the open/close status of doors or windows.

704

705

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379210849-860.png?rev=1.1||alt="1656379210849-860.png"]]

706

707

When the two pieces are close to each other, the 2 wire output will be short or open (depending on the type), while if the two pieces are away from each other, the 2 wire output will be the opposite status. So we can use SN50_v3 interrupt interface to detect the status for the door or window.

708

709

**~ Below is the installation example:**

710

711

Fix one piece of the magnetic sensor to the door and connect the two pins to SN50_v3 as follows:

712

713

* (((

714

One pin to SN50_v3's PA8 pin

715

)))

716

* (((

717

The other pin to SN50_v3's VDD pin

718

)))

719

720

Install the other piece to the door. Find a place where the two pieces will be close to each other when the door is closed. For this particular magnetic sensor, when the door is closed, the output will be short, and PA8 will be at the VCC voltage.

721

722

Door sensors have two types: ** NC (Normal close)** and **NO (normal open)**. The connection for both type sensors are the same. But the decoding for payload are reverse, user need to modify this in the IoT Server decoder.

723

724

When door sensor is shorted, there will extra power consumption in the circuit, the extra current is 3v3/R14 = 3v3/1Mohm = 3uA which can be ignored.

725

726

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379283019-229.png?rev=1.1||alt="1656379283019-229.png"]]

727

728

The above photos shows the two parts of the magnetic switch fitted to a door.

729

730

The software by default uses the falling edge on the signal line as an interrupt. We need to modify it to accept both the rising edge (0v ~-~-> VCC , door close) and the falling edge (VCC ~-~-> 0v , door open) as the interrupt.

The command is:

**AT+INTMOD1=1 **~/~/(more info about INMOD please refer** **[[**AT Command Manual**>>url:http://www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/&file=DRAGINO_LSN50_AT_Commands_v1.5.1.pdf]]**. **)

735

736

Below shows some screen captures in TTN V3:

737

738

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379339508-835.png?rev=1.1||alt="1656379339508-835.png"]]

739

740

In MOD=1, user can use byte 6 to see the status for door open or close. TTN V3 decoder is as below:

741

742

door= (bytes[6] & 0x80)? "CLOSE":"OPEN";

743

744

745

==== 2.3.3.6 I2C Interface (SHT20 & SHT31) ====

746

747

The SDA and SCK are I2C interface lines. You can use these to connect to an I2C device and get the sensor data.

748

749

We have made an example to show how to use the I2C interface to connect to the SHT20 Temperature and Humidity Sensor.

750

751

Notice: Different I2C sensors have different I2C commands set and initiate process, if user want to use other I2C sensors, User need to re-write the source code to support those sensors. SHT20 code in SN50_v3 will be a good reference.

752

753

Below is the connection to SHT20/ SHT31. The connection is as below:

754

755

756

[[image:image-20230513103633-3.png||height="636" width="1017"]]

757

758

The device will be able to get the I2C sensor data now and upload to IoT Server.

759

760

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379664142-345.png?rev=1.1||alt="1656379664142-345.png"]]

761

762

Convert the read byte to decimal and divide it by ten.

**Example:**

Temperature: Read:0116(H) = 278(D) Value: 278 /10=27.8℃;

767

768

Humidity: Read:0248(H)=584(D) Value: 584 / 10=58.4, So 58.4%

769

770

If you want to use other I2C device, please refer the SHT20 part source code as reference.

771

772

773

==== 2.3.3.7 Distance Reading ====

774

775

Refer [[Ultrasonic Sensor section>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#H2.4.8UltrasonicSensor]].

776

777

778

==== 2.3.3.8 Ultrasonic Sensor ====

779

780

This Fundamental Principles of this sensor can be found at this link: [[https:~~/~~/wiki.dfrobot.com/Weather_-_proof_Ultrasonic_Sensor_with_Separate_Probe_SKU~~_~~__SEN0208>>url:https://wiki.dfrobot.com/Weather_-_proof_Ultrasonic_Sensor_with_Separate_Probe_SKU___SEN0208]]

781

782

The SN50_v3 detects the pulse width of the sensor and converts it to mm output. The accuracy will be within 1 centimeter. The usable range (the distance between the ultrasonic probe and the measured object) is between 24cm and 600cm.

783

784

The working principle of this sensor is similar to the **HC-SR04** ultrasonic sensor.

785

786

The picture below shows the connection:

787

788

[[image:image-20230512173903-6.png||height="596" width="715"]]

789

790

Connect to the SN50_v3 and run **AT+MOD=2** to switch to ultrasonic mode (ULT).

791

792

The ultrasonic sensor uses the 8^^th^^ and 9^^th^^ byte for the measurement value.

**Example:**

Distance: Read: 0C2D(Hex) = 3117(D) Value: 3117 mm=311.7 cm

==== 2.3.3.9 Battery Output - BAT pin ====

801

802

The BAT pin of SN50v3 is connected to the Battery directly. If users want to use BAT pin to power an external sensor. User need to make sure the external sensor is of low power consumption. Because the BAT pin is always open. If the external sensor is of high power consumption. the battery of SN50v3-LB will run out very soon.

803

804

805

==== 2.3.3.10 +5V Output ====

806

807

SN50v3 will enable +5V output before all sampling and disable the +5v after all sampling.

808

809

The 5V output time can be controlled by AT Command.

**AT+5VT=1000**

Means set 5V valid time to have 1000ms. So the real 5V output will actually have 1000ms + sampling time for other sensors.

814

815

By default the AT+5VT=500. If the external sensor which require 5v and require more time to get stable state, user can use this command to increase the power ON duration for this sensor.

==== 2.3.3.11 BH1750 Illumination Sensor ====

820

821

MOD=1 support this sensor. The sensor value is in the 8^^th^^ and 9^^th^^ bytes.

822

823

[[image:image-20230512172447-4.png||height="593" width="1015"]]

824

825

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220628110012-12.png?rev=1.1||alt="image-20220628110012-12.png"]]

826

827

828

==== 2.3.3.12 Working MOD ====

829

830

The working MOD info is contained in the Digital in & Digital Interrupt byte (7^^th^^ Byte).

831

832

User can use the 3^^rd^^ ~~ 7^^th^^ bit of this byte to see the working mod:

833

834

Case 7^^th^^ Byte >> 2 & 0x1f:

* 0: MOD1

* 1: MOD2

* 2: MOD3

* 3: MOD4

* 4: MOD5

* 5: MOD6

* 6: MOD7

* 7: MOD8

* 8: MOD9

== 2.4 Payload Decoder file ==

847

848

849

In TTN, use can add a custom payload so it shows friendly reading

850

851

In the page (% style="color:#037691" %)**Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder**(%%) to add the decoder from:

852

853

[[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/LSN50v2-S31%26S31B >>https://github.com/dragino/dragino-end-node-decoder/tree/main/LSN50v2-S31%26S31B]]

== 2.5 Frequency Plans ==

858

859

860

The SN50v3-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.

861

862

[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]

863

864

865

= 3. Configure SN50v3-LB =

866

867

== 3.1 Configure Methods ==

868

869

870

SN50v3-LB supports below configure method:

871

872

* AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].

873

* AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].

874

* LoRaWAN Downlink. Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.

875

876

== 3.2 General Commands ==

877

878

879

These commands are to configure:

880

881

* General system settings like: uplink interval.

882

* LoRaWAN protocol & radio related command.

883

884

They are same for all Dragino Devices which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:

885

886

[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]

887

888

889

== 3.3 Commands special design for SN50v3-LB ==

890

891

892

These commands only valid for S31x-LB, as below:

893

894

895

=== 3.3.1 Set Transmit Interval Time ===

896

897

898

Feature: Change LoRaWAN End Node Transmit Interval.

899

900

(% style="color:blue" %)**AT Command: AT+TDC**

901

902

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

903

|=(% style="width: 156px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 137px;background-color:#D9E2F3" %)**Function**|=(% style="background-color:#D9E2F3" %)**Response**

904

|(% style="width:156px" %)AT+TDC=?|(% style="width:137px" %)Show current transmit Interval|(((

905

30000

906

OK

907

the interval is 30000ms = 30s

908

)))

909

|(% style="width:156px" %)AT+TDC=60000|(% style="width:137px" %)Set Transmit Interval|(((

910

OK

911

Set transmit interval to 60000ms = 60 seconds

912

)))

913

914

(% style="color:blue" %)**Downlink Command: 0x01**

915

916

Format: Command Code (0x01) followed by 3 bytes time value.

917

918

If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.

919

920

* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds

921

* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds

922

923

=== 3.3.2 Get Device Status ===

924

925

Send a LoRaWAN downlink to ask device send Alarm settings.

926

927

(% style="color:blue" %)**Downlink Payload: **(%%)0x26 01

928

929

Sensor will upload Device Status via FPORT=5. See payload section for detail.

930

931

932

=== 3.3.3 Set Interrupt Mode ===

933

934

935

Feature, Set Interrupt mode for GPIO_EXIT.

936

937

(% style="color:blue" %)**AT Command: AT+INTMOD1，AT+INTMOD2，AT+INTMOD3**

938

939

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

940

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

941

|(% style="width:154px" %)AT+INTMOD1=?|(% style="width:196px" %)Show current interrupt mode|(% style="width:157px" %)(((

942

0

943

OK

944

the mode is 0 =Disable Interrupt

945

)))

946

|(% style="width:154px" %)AT+INTMOD1=2|(% style="width:196px" %)(((

947

Set Transmit Interval

948

0. (Disable Interrupt),

949

~1. (Trigger by rising and falling edge)

950

2. (Trigger by falling edge)

951

3. (Trigger by rising edge)

952

)))|(% style="width:157px" %)OK

953

|(% style="width:154px" %)AT+INTMOD2=3|(% style="width:196px" %)(((

954

Set Transmit Interval

955

956

trigger by rising edge.

957

)))|(% style="width:157px" %)OK

958

|(% style="width:154px" %)AT+INTMOD3=0|(% style="width:196px" %)Disable Interrupt|(% style="width:157px" %)OK

959

960

(% style="color:blue" %)**Downlink Command: 0x06**

961

962

Format: Command Code (0x06) followed by 3 bytes.

963

964

This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.

965

966

* Example 1: Downlink Payload: 06000000 **~-~-->** AT+INTMOD1=0

967

* Example 2: Downlink Payload: 06000003 **~-~-->** AT+INTMOD1=3

968

* Example 3: Downlink Payload: 06000102 **~-~-->** AT+INTMOD2=2

969

* Example 4: Downlink Payload: 06000201 **~-~-->** AT+INTMOD3=1

970

971

(% class="wikigeneratedid" %)

972

=== 3.3.4 Set Power Output Duration ===

973

974

Control the output duration 5V . Before each sampling, device will

975

976

~1. first enable the power output to external sensor,

977

978

2. keep it on as per duration, read sensor value and construct uplink payload

979

980

3. final, close the power output.

981

982

(% style="color:blue" %)**AT Command: AT+5VT**

983

984

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

985

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

986

|(% style="width:154px" %)AT+5VT=?|(% style="width:196px" %)Show 5V open time.|(% style="width:157px" %)(((

500(default)

OK

)))

|(% style="width:154px" %)AT+5VT=1000|(% style="width:196px" %)(((

992

Close after a delay of 1000 milliseconds.

993

)))|(% style="width:157px" %)OK

994

995

(% style="color:blue" %)**Downlink Command: 0x07**

996

997

Format: Command Code (0x07) followed by 2 bytes.

998

999

The first and second bytes are the time to turn on.

1000

1001

* Example 1: Downlink Payload: 070000 **~-~-->** AT+5VT=0

1002

* Example 2: Downlink Payload: 0701F4 **~-~-->** AT+5VT=500

1003

1004

(% class="wikigeneratedid" %)

1005

=== 3.3.5 Set Weighing parameters ===

1006

1007

Feature: Working mode 5 is effective, hair removal and setting of weight factor of HX711.

1008

1009

(% style="color:blue" %)**AT Command: AT+WEIGRE,AT+WEIGAP**

1010

1011

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

1012

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

1013

|(% style="width:154px" %) |(% style="width:196px" %) |(% style="width:157px" %)

1014

|(% style="width:154px" %) |(% style="width:196px" %) |(% style="width:157px" %)

1015

1016

1017

(% style="color:blue" %)**Downlink Command: 0x08**

1018

1019

1020

Format: Command Code (0x07) followed by 2 bytes.

1021

1022

The first and second bytes are the time to turn on.

1023

1024

1025

=== 3.3.6 Set Digital pulse count value ===

1026

1027

Feature: Set the pulse count value.

1028

1029

(% style="color:blue" %)**AT Command: AT+SETCNT**

1030

1031

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

1032

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

1033

|(% style="width:154px" %)AT+SETCNT=1,100|(% style="width:196px" %)Initialize the count value 1 to 100.|(% style="width:157px" %)OK

1034

|(% style="width:154px" %)AT+SETCNT=2,0|(% style="width:196px" %)Initialize the count value 2 to 0.|(% style="width:157px" %)OK

1035

1036

1037

(% style="color:blue" %)**Downlink Command: 0x09**

1038

1039

1040

Format: Command Code (0x09) followed by 5 bytes.

1041

1042

The first byte is to select which count value to initialize, and the next four bytes are the count value to be initialized.

1043

1044

* Example 1: Downlink Payload: 090100000000 **~-~-->** AT+SETCNT=1,0

1045

* Example 2: Downlink Payload: 090200000000 **~-~-->** AT+5VT=500

1046

1047

=== 3.3.7 Set Workmode ===

1048

1049

Feature: switch working mode.

1050

1051

(% style="color:blue" %)**AT Command: AT+MOD**

1052

1053

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

1054

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

1055

|(% style="width:154px" %)AT+MOD=?|(% style="width:196px" %)Get the current working mode.|(% style="width:157px" %)(((

1056

OK

1057

)))

1058

|(% style="width:154px" %)AT+MOD=4|(% style="width:196px" %)Set the working mode to 3DS18B20s.|(% style="width:157px" %)(((

1059

OK

1060

1061

Attention:Take effect after ATZ

)))

(% style="color:blue" %)**Downlink Command: 0x0A**

1066

1067

1068

Format: Command Code (0x0A) followed by 1 bytes.

1069

1070

* Example 1: Downlink Payload: 0A01 **~-~-->** AT+MOD=1

1071

* Example 2: Downlink Payload: 0A04 **~-~-->** AT+MOD=4

1072

1073

= 4. Battery & Power Consumption =

1074

1075

1076

SN50v3-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.

1077

1078

[[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .

1079

1080

1081

= 5. OTA Firmware update =

1082

1083

1084

(% class="wikigeneratedid" %)

1085

User can change firmware SN50v3-LB to:

1086

1087

* Change Frequency band/ region.

1088

* Update with new features.

1089

* Fix bugs.

1090

1091

Firmware and changelog can be downloaded from : **[[Firmware download link>>url:https://www.dropbox.com/sh/kwqv57tp6pejias/AAAopYMATh1GM6fZ-VRCLrpDa?dl=0]]**

1092

1093

1094

Methods to Update Firmware:

1095

1096

* (Recommanded way) OTA firmware update via wireless: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]

1097

* Update through UART TTL interface.**[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.

= 6. FAQ =

== 6.1 Where can i find source code of SN50v3-LB? ==

1102

1103

* **[[Hardware Source Files>>https://github.com/dragino/Lora/tree/master/LSN50/v3.0]].**

1104

* **[[Software Source Code & Compile instruction>>https://github.com/dragino/SN50v3]].**

= 7. Order Info =

Part Number: (% style="color:blue" %)**SN50v3-LB-XX-YY**

1110

1111

(% style="color:red" %)**XX**(%%): The default frequency band

1112

1113

* (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band

1114

* (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band

1115

* (% style="color:red" %)**EU433**(%%): LoRaWAN EU433 band

1116

* (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band

1117

* (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band

1118

* (% style="color:red" %)**US915**(%%): LoRaWAN US915 band

1119

* (% style="color:red" %)**IN865**(%%): LoRaWAN IN865 band

1120

* (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band

1121

1122

(% style="color:red" %)**YY: ** (%%)Hole Option

1123

1124

* (% style="color:red" %)**12**(%%): With M12 waterproof cable hole

1125

* (% style="color:red" %)**16**(%%): With M16 waterproof cable hole

1126

* (% style="color:red" %)**20**(%%): With M20 waterproof cable hole

1127

* (% style="color:red" %)**NH**(%%): No Hole

= 8. Packing Info =

(% style="color:#037691" %)**Package Includes**:

1132

1133

* SN50v3-LB LoRaWAN Generic Node

1134

1135

(% style="color:#037691" %)**Dimension and weight**:

* Device Size: cm

* Device Weight: g

* Package Size / pcs : cm

* Weight / pcs : g

= 9. Support =

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

1146

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]

Wiki source code of SN50v3-LB User Manual

Applications

Navigation