SN50v3-LB LoRaWAN Sensor Node User Manual

(% style="color:blue" %)**SN50V3-LB **(%%)LoRaWAN Sensor Node is a Long Range LoRa Sensor Node. It is designed for outdoor use and powered by (% style="color:blue" %)** 8500mA Li/SOCl2 battery**(%%) for long term use.SN50V3-LB is designed to facilitate developers to quickly deploy industrial level LoRa and IoT solutions. It help users to turn the idea into a practical application and make the Internet of Things a reality. It is easy to program, create and connect your things everywhere.

21

22

(% style="color:blue" %)**SN50V3-LB wireless part**(%%) is based on SX1262 allows the user to send data and reach extremely long ranges at low data-rates.It provides ultra-long range spread spectrum communication and high interference immunity whilst minimising current consumption.It targets professional wireless sensor network applications such as irrigation systems, smart metering, smart cities, smartphone detection, building automation, and so on.

23

24

(% style="color:blue" %)**SN50V3-LB **(%%)has a powerful 48Mhz ARM microcontroller with 256KB flash and 64KB RAM. It has multiplex I/O pins to connect to different sensors.

25

26

(% style="color:blue" %)**SN50V3-LB**(%%) has a built-in BLE module, user can configure the sensor remotely via Mobile Phone. It also support OTA upgrade via private LoRa protocol for easy maintaining.

27

28

SN50V3-LB is the 3^^rd^^ generation of LSN50 series generic sensor node from Dragino. It is an (% style="color:blue" %)**open source project**(%%) and has a mature LoRaWAN stack and application software. User can use the pre-load software for their IoT projects or easily customize the software for different requirements.

== 1.2 Features ==

* LoRaWAN 1.0.3 Class A

34

* Ultra-low power consumption

35

* Open-Source hardware/software

36

* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865

37

* Support Bluetooth v5.1 and LoRaWAN remote configure

38

* Support wireless OTA update firmware

39

* Uplink on periodically

40

* Downlink to change configure

41

* 8500mAh Battery for long term use

42

43

== 1.3 Specification ==

44

45

(% style="color:#037691" %)**Common DC Characteristics:**

46

47

* Supply Voltage: built in 8500mAh Li-SOCI2 battery , 2.5v ~~ 3.6v

48

* Operating Temperature: -40 ~~ 85°C

49

50

(% style="color:#037691" %)**I/O Interface:**

51

52

* Battery output (2.6v ~~ 3.6v depends on battery)

53

* +5v controllable output

54

* 3 x Interrupt or Digital IN/OUT pins

55

* 3 x one-wire interfaces

* 1 x UART Interface

* 1 x I2C Interface

(% style="color:#037691" %)**LoRa Spec:**

60

61

* Frequency Range, Band 1 (HF): 862 ~~ 1020 Mhz

62

* Max +22 dBm constant RF output vs.

63

* RX sensitivity: down to -139 dBm.

64

* Excellent blocking immunity

65

66

(% style="color:#037691" %)**Battery:**

67

68

* Li/SOCI2 un-chargeable battery

69

* Capacity: 8500mAh

70

* Self-Discharge: <1% / Year @ 25°C

71

* Max continuously current: 130mA

72

* Max boost current: 2A, 1 second

73

74

(% style="color:#037691" %)**Power Consumption**

75

76

* Sleep Mode: 5uA @ 3.3v

77

* LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm

78

79

== 1.4 Sleep mode and working mode ==

80

81

(% style="color:blue" %)**Deep Sleep Mode: **(%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.

82

83

(% style="color:blue" %)**Working Mode:** (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.

84

85

86

== 1.5 Button & LEDs ==

87

88

89

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675071855856-879.png]]

90

91

92

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

93

|=(% style="width: 167px;background-color:#D9E2F3;color:#0070C0" %)**Behavior on ACT**|=(% style="width: 117px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 225px;background-color:#D9E2F3;color:#0070C0" %)**Action**

94

|(% style="width:167px" %)Pressing ACT between 1s < time < 3s|(% style="width:117px" %)Send an uplink|(% style="width:225px" %)(((

95

If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, (% style="color:blue" %)**blue led** (%%)will blink once.

96

Meanwhile, BLE module will be active and user can connect via BLE to configure device.

97

)))

98

|(% style="width:167px" %)Pressing ACT for more than 3s|(% style="width:117px" %)Active Device|(% style="width:225px" %)(((

99

(% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:#037691" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network.

100

(% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.

101

Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device join or not join LoRaWAN network.

102

)))

103

|(% style="width:167px" %)Fast press ACT 5 times.|(% style="width:117px" %)Deactivate Device|(% style="width:225px" %)(% style="color:red" %)**Red led**(%%) will solid on for 5 seconds. Means device is in Deep Sleep Mode.

104

105

== 1.6 BLE connection ==

106

107

108

SN50v3-LB supports BLE remote configure.

109

110

111

BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:

112

113

* Press button to send an uplink

114

* Press button to active device.

115

* Device Power on or reset.

116

117

If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.

118

119

120

== 1.7 Pin Definitions ==

121

122

123

[[image:image-20230513102034-2.png]]

== 1.8 Mechanical ==

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143884058-338.png]]

130

131

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143899218-599.png]]

132

133

[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143909447-639.png]]

== Hole Option ==

SN50v3-LB has different hole size options for different size sensor cable. The options provided are M12, M16 and M20. The definition is as below:

139

140

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220627104757-1.png?rev=1.1||alt="image-20220627104757-1.png"]]

141

142

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656298089706-973.png?rev=1.1||alt="1656298089706-973.png"]]

143

144

145

= 2. Configure SN50v3-LB to connect to LoRaWAN network =

146

147

== 2.1 How it works ==

148

149

150

The SN50v3-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the S31x-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.

151

152

153

== 2.2 Quick guide to connect to LoRaWAN server (OTAA) ==

154

155

156

Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.

157

158

The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.

159

160

161

(% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from SN50v3-LB.

162

163

Each SN50v3-LB is shipped with a sticker with the default device EUI as below:

164

165

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/S31-LB_S31B-LB/WebHome/image-20230426084152-1.png?width=502&height=233&rev=1.1||alt="图片-20230426084152-1.png" height="233" width="502"]]

166

167

168

You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:

169

170

171

(% style="color:blue" %)**Register the device**

172

173

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/1654935135620-998.png?rev=1.1||alt="1654935135620-998.png"]]

174

175

176

(% style="color:blue" %)**Add APP EUI and DEV EUI**

177

178

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-4.png?width=753&height=551&rev=1.1||alt="图片-20220611161308-4.png"]]

179

180

181

(% style="color:blue" %)**Add APP EUI in the application**

182

183

184

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-5.png?width=742&height=601&rev=1.1||alt="图片-20220611161308-5.png"]]

185

186

187

(% style="color:blue" %)**Add APP KEY**

188

189

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-6.png?width=744&height=485&rev=1.1||alt="图片-20220611161308-6.png"]]

190

191

192

(% style="color:blue" %)**Step 2:**(%%) Activate SN50v3-LB

193

194

195

Press the button for 5 seconds to activate the SN50v3-LB.

196

197

(% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:blue" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.

198

199

After join success, it will start to upload messages to TTN and you can see the messages in the panel.

200

201

202

== 2.3 Uplink Payload ==

203

204

=== 2.3.1 Device Status, FPORT~=5 ===

205

206

207

Users can use the downlink command(**0x26 01**) to ask SN50v3 to send device configure detail, include device configure status. SN50v3 will uplink a payload via FPort=5 to server.

208

209

The Payload format is as below.

210

211

212

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

213

|(% colspan="6" style="background-color:#d9e2f3; color:#0070c0" %)**Device Status (FPORT=5)**

Example parse in TTNv3

218

219

220

(% style="color:#037691" %)**Sensor Model**(%%): For SN50v3, this value is 0x1C

221

222

(% style="color:#037691" %)**Firmware Version**(%%): 0x0100, Means: v1.0.0 version

223

224

(% style="color:#037691" %)**Frequency Band**:

*0x01: EU868

*0x02: US915

*0x03: IN865

*0x04: AU915

*0x05: KZ865

*0x06: RU864

*0x07: AS923

*0x08: AS923-1

*0x09: AS923-2

*0x0a: AS923-3

*0x0b: CN470

*0x0c: EU433

*0x0d: KR920

*0x0e: MA869

(% style="color:#037691" %)**Sub-Band**:

256

257

AU915 and US915:value 0x00 ~~ 0x08

258

259

CN470: value 0x0B ~~ 0x0C

260

261

Other Bands: Always 0x00

262

263

264

(% style="color:#037691" %)**Battery Info**:

265

266

Check the battery voltage.

Ex1: 0x0B45 = 2885mV

Ex2: 0x0B49 = 2889mV

=== 2.3.2 Working Modes & Sensor Data. Uplink via FPORT~=2 ===

274

275

276

SN50v3 has different working mode for the connections of different type of sensors. This section describes these modes. Use can use the AT Command AT+MOD to set SN50v3 to different working modes.

For example:

**AT+MOD=2 ** ~/~/ will set the SN50v3 to work in MOD=2 distance mode which target to measure distance via Ultrasonic Sensor.

281

282

283

(% style="color:red" %) **Important Notice:**

284

285

1. Some working modes has payload more than 12 bytes, The US915/AU915/AS923 frequency bands' definition has maximum 11 bytes in **DR0**. Server sides will see NULL payload while SN50v3 transmit in DR0 with 12 bytes payload.

286

1. All modes share the same Payload Explanation from HERE.

287

1. By default, the device will send an uplink message every 20 minutes.

288

289

==== 2.3.2.1 MOD~=1 (Default Mode) ====

290

291

In this mode, uplink payload includes in total 11 bytes. Uplink packets use FPORT=2.

292

293

(% style="width:1110px" %)

294

295

|**Value**|Bat|(% style="width:191px" %)(((

Temperature(DS18B20)

(PC13)

)))|(% style="width:78px" %)(((

ADC

(PA4)

)))|(% style="width:216px" %)(((

304

Digital in(PB15) &

305

306

Digital Interrupt(PA8)

307

308

309

)))|(% style="width:308px" %)(((

310

Temperature

311

312

(SHT20 or SHT31 or BH1750 Illumination Sensor)

313

)))|(% style="width:154px" %)(((

Humidity

(SHT20 or SHT31)

)))

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220627150949-6.png?rev=1.1||alt="image-20220627150949-6.png"]]

320

321

322

==== 2.3.2.2 MOD~=2 (Distance Mode) ====

323

324

This mode is target to measure the distance. The payload of this mode is totally 11 bytes. The 8^^th^^ and 9^^th^^ bytes is for the distance.

325

326

(% style="width:1011px" %)

327

328

|**Value**|BAT|(% style="width:196px" %)(((

Temperature(DS18B20)

(PC13)

)))|(% style="width:87px" %)(((

ADC

(PA4)

)))|(% style="width:189px" %)(((

337

Digital in(PB15) &

338

339

Digital Interrupt(PA8)

340

)))|(% style="width:208px" %)(((

Distance measure by:

1) LIDAR-Lite V3HP

Or

2) Ultrasonic Sensor

)))|(% style="width:117px" %)Reserved

346

347

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656324539647-568.png?rev=1.1||alt="1656324539647-568.png"]]

348

349

**Connection of LIDAR-Lite V3HP:**

350

351

[[image:image-20230512173758-5.png||height="563" width="712"]]

352

353

**Connection to Ultrasonic Sensor:**

354

355

Need to remove R1 and R2 resistors to get low power,otherwise there will be 240uA standby current.

356

357

[[image:image-20230512173903-6.png||height="596" width="715"]]

358

359

For the connection to TF-Mini or TF-Luna , MOD2 payload is as below:

360

361

(% style="width:1113px" %)

362

363

|**Value**|BAT|(% style="width:183px" %)(((

Temperature(DS18B20)

(PC13)

)))|(% style="width:173px" %)(((

368

Digital in(PB15) &

369

370

Digital Interrupt(PA8)

371

)))|(% style="width:84px" %)(((

ADC

(PA4)

)))|(% style="width:323px" %)(((

376

Distance measure by:1)TF-Mini plus LiDAR

377

Or

378

2) TF-Luna LiDAR

379

)))|(% style="width:188px" %)Distance signal strength

380

381

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656376779088-686.png?rev=1.1||alt="1656376779088-686.png"]]

382

383

**Connection to [[TF-Mini plus>>url:http://en.benewake.com/product/detail/5c345cd0e5b3a844c472329b.html]] LiDAR(UART version):**

384

385

Need to remove R3 and R4 resistors to get low power,otherwise there will be 400uA standby current.

386

387

[[image:image-20230512180609-7.png||height="555" width="802"]]

388

389

**Connection to [[TF-Luna>>url:http://en.benewake.com/product/detail/5e1c1fd04d839408076b6255.html]] LiDAR (UART version):**

390

391

Need to remove R3 and R4 resistors to get low power,otherwise there will be 400uA standby current.

392

393

[[image:image-20230513105207-4.png||height="469" width="802"]]

394

395

396

==== 2.3.2.3 MOD~=3 (3 ADC + I2C) ====

397

398

This mode has total 12 bytes. Include 3 x ADC + 1x I2C

399

400

(% style="width:1031px" %)

|=(((

**Size(bytes)**

|**Value**|(% style="width:68px" %)(((

ADC1

(PA4)

)))|(% style="width:75px" %)(((

ADC2

(PA5)

)))|(((

ADC3

(PA8)

)))|(((

Digital Interrupt(PB15)

418

)))|(% style="width:304px" %)(((

419

Temperature

420

421

(SHT20 or SHT31 or BH1750 Illumination Sensor)

422

)))|(% style="width:163px" %)(((

Humidity

(SHT20 or SHT31)

)))|(% style="width:53px" %)Bat

427

428

[[image:image-20230513110214-6.png]]

429

430

431

==== 2.3.2.4 MOD~=4 (3 x DS18B20) ====

432

433

434

This mode has total 11 bytes. As shown below:

435

436

(% style="width:1017px" %)

437

438

|**Value**|BAT|(% style="width:186px" %)(((

439

Temperature1(DS18B20)

440

(PC13)

441

)))|(% style="width:82px" %)(((

ADC

(PA4)

)))|(% style="width:210px" %)(((

446

Digital in(PB15) &

447

448

Digital Interrupt(PA8)

449

)))|(% style="width:191px" %)Temperature2(DS18B20)

450

(PB9)|(% style="width:183px" %)Temperature3(DS18B20)

451

(PB8)

452

453

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656377606181-607.png?rev=1.1||alt="1656377606181-607.png"]]

454

455

[[image:image-20230513134006-1.png||height="559" width="736"]]

456

457

458

==== 2.3.2.5 MOD~=5(Weight Measurement by HX711) ====

459

460

[[image:image-20230512164658-2.png||height="532" width="729"]]

461

462

Each HX711 need to be calibrated before used. User need to do below two steps:

463

464

1. Zero calibration. Don't put anything on load cell and run **AT+WEIGRE** to calibrate to Zero gram.

465

1. Adjust calibration factor (default value 400): Put a known weight thing on load cell and run **AT+WEIGAP** to adjust the Calibration Factor.

466

1. (((

467

Weight has 4 bytes, the unit is g.

)))

For example:

**AT+GETSENSORVALUE =0**

473

474

Response: Weight is 401 g

475

476

Check the response of this command and adjust the value to match the real value for thing.

477

478

(% style="width:767px" %)

|=(((

**Size(bytes)**

|**Value**|BAT|(% style="width:193px" %)(((

Temperature(DS18B20)

(PC13)

)))|(% style="width:85px" %)(((

ADC

(PA4)

)))|(% style="width:186px" %)(((

493

Digital in(PB15) &

494

495

Digital Interrupt(PA8)

496

)))|(% style="width:100px" %)Weight

497

498

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220820120036-2.png?width=1003&height=469&rev=1.1||alt="image-20220820120036-2.png" height="469" width="1003"]]

499

500

501

==== 2.3.2.6 MOD~=6 (Counting Mode) ====

502

503

In this mode, the device will work in counting mode. It counts the interrupt on the interrupt pins and sends the count on TDC time.

504

505

Connection is as below. The PIR sensor is a count sensor, it will generate interrupt when people come close or go away. User can replace the PIR sensor with other counting sensors.

506

507

[[image:image-20230512181814-9.png||height="543" width="697"]]

508

509

**Note:** LoRaWAN wireless transmission will infect the PIR sensor. Which cause the counting value increase +1 for every uplink. User can change PIR sensor or put sensor away of the SN50_v3 to avoid this happen.

510

511

(% style="width:961px" %)

512

513

|**Value**|BAT|(% style="width:256px" %)(((

Temperature(DS18B20)

(PC13)

)))|(% style="width:108px" %)(((

ADC

(PA4)

)))|(% style="width:126px" %)(((

Digital in

(PB15)

)))|(% style="width:145px" %)(((

Count

(PA8)

)))

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656378441509-171.png?rev=1.1||alt="1656378441509-171.png"]]

532

533

534

==== 2.3.2.7 MOD~=7 (Three interrupt contact modes) ====

535

536

(% style="width:1108px" %)

|=(((

**Size(bytes)**

|**Value**|BAT|(% style="width:188px" %)(((

Temperature(DS18B20)

(PC13)

)))|(% style="width:83px" %)(((

ADC

(PA5)

)))|(% style="width:184px" %)(((

549

Digital Interrupt1(PA8)

550

)))|(% style="width:186px" %)Digital Interrupt2(PA4)|(% style="width:197px" %)Digital Interrupt3(PB15)|(% style="width:100px" %)Reserved

551

552

[[image:image-20230513111203-7.png||height="324" width="975"]]

553

554

==== 2.3.2.8 MOD~=8 （3ADC+1DS18B20） ====

555

556

(% style="width:922px" %)

|=(((

**Size(bytes)**

|**Value**|BAT|(% style="width:207px" %)(((

Temperature(DS18B20)

(PC13)

)))|(% style="width:94px" %)(((

ADC1

(PA4)

)))|(% style="width:198px" %)(((

569

Digital Interrupt(PB15)

570

)))|(% style="width:84px" %)(((

ADC2

(PA5)

)))|(% style="width:82px" %)(((

ADC3

(PA8)

)))

[[image:image-20230513111231-8.png||height="335" width="900"]]

581

582

583

==== 2.3.2.9 MOD~=9 (3DS18B20+ two Interrupt count mode) ====

584

585

(% style="width:1010px" %)

586

|=(((

587

**Size(bytes)**

588

)))|=**2**|=**2**|=**2**|=**1**|=(% style="width: 193px;" %)**2**|=(% style="width: 78px;" %)4|=(% style="width: 78px;" %)4

589

|**Value**|BAT|(((

590

Temperature1(DS18B20)

(PC13)

)))|(((

Temperature2(DS18B20)

(PB9)

)))|(((

Digital Interrupt

(PB15)

)))|(% style="width:193px" %)(((

602

Temperature3(DS18B20)

603

604

(PB8)

605

)))|(% style="width:78px" %)(((

Count1

(PA8)

)))|(% style="width:78px" %)(((

Count2

(PA4)

)))

[[image:image-20230513111255-9.png||height="341" width="899"]]

616

617

**The newly added AT command is issued correspondingly:**

618

619

**~ AT+INTMOD1** ** PA8** pin： Corresponding downlink: **06 00 00 xx**

620

621

**~ AT+INTMOD2** **PA4** pin： Corresponding downlink:** 06 00 01 xx**

622

623

**~ AT+INTMOD3** **PB15** pin： Corresponding downlink: ** 06 00 02 xx**

**AT+SETCNT=aa,bb**

When AA is 1, set the count of PA8 pin to BB Corresponding downlink：09 01 bb bb bb bb

628

629

When AA is 2, set the count of PA4 pin to BB Corresponding downlink：09 02 bb bb bb bb

=== 2.3.3 Decode payload ===

634

635

While using TTN V3 network, you can add the payload format to decode the payload.

636

637

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656378466788-734.png?rev=1.1||alt="1656378466788-734.png"]]

638

639

The payload decoder function for TTN V3 are here:

640

641

SN50v3 TTN V3 Payload Decoder: [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>url:https://github.com/dragino/dragino-end-node-decoder]]

642

643

644

==== 2.3.3.1 Battery Info ====

645

646

Check the battery voltage for SN50v3.

Ex1: 0x0B45 = 2885mV

Ex2: 0x0B49 = 2889mV

==== 2.3.3.2 Temperature (DS18B20) ====

654

655

If there is a DS18B20 connected to PC13 pin. The temperature will be uploaded in the payload.

656

657

More DS18B20 can check the [[3 DS18B20 mode>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#2.3.4MOD3D4283xDS18B2029]]

**Connection:**

[[image:image-20230512180718-8.png||height="538" width="647"]]

**Example**:

If payload is: 0105H: (0105 & 8000 == 0), temp = 0105H /10 = 26.1 degree

666

667

If payload is: FF3FH : (FF3F & 8000 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.

668

669

（FF3F & 8000：Judge whether the highest bit is 1, when the highest bit is 1, it is negative）

670

671

672

==== 2.3.3.3 Digital Input ====

673

674

The digital input for pin PB15,

675

676

* When PB15 is high, the bit 1 of payload byte 6 is 1.

677

* When PB15 is low, the bit 1 of payload byte 6 is 0.

678

679

(% class="wikigeneratedid" id="H2.3.3.4A0AnalogueDigitalConverter28ADC29" %)

680

(((

681

When the digital interrupt pin is set to AT+INTMODx=0, this pin is used as a digital input pin.

682

683

**Note:**The maximum voltage input supports 3.6V.

)))

==== 2.3.3.4 Analogue Digital Converter (ADC) ====

689

690

The measuring range of the ADC is only about 0V to 1.1V The voltage resolution is about 0.24mv.

691

692

When the measured output voltage of the sensor is not within the range of 0V and 1.1V, the output voltage terminal of the sensor shall be divided The example in the following figure is to reduce the output voltage of the sensor by three times If it is necessary to reduce more times, calculate according to the formula in the figure and connect the corresponding resistance in series.

693

694

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220628150112-1.png?width=285&height=241&rev=1.1||alt="image-20220628150112-1.png" height="241" width="285"]]

695

696

**Note:**If the ADC type sensor needs to be powered by SN50_v3, it is recommended to use +5V to control its switch.Only sensors with low power consumption can be powered with VDD.

697

698

699

==== 2.3.3.5 Digital Interrupt ====

700

701

Digital Interrupt refers to pin PA8, and there are different trigger methods. When there is a trigger, the SN50v3 will send a packet to the server.

702

703

**~ Interrupt connection method:**

704

705

[[image:image-20230513105351-5.png||height="147" width="485"]]

706

707

**Example to use with door sensor :**

708

709

The door sensor is shown at right. It is a two wire magnetic contact switch used for detecting the open/close status of doors or windows.

710

711

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379210849-860.png?rev=1.1||alt="1656379210849-860.png"]]

712

713

When the two pieces are close to each other, the 2 wire output will be short or open (depending on the type), while if the two pieces are away from each other, the 2 wire output will be the opposite status. So we can use SN50_v3 interrupt interface to detect the status for the door or window.

714

715

**~ Below is the installation example:**

716

717

Fix one piece of the magnetic sensor to the door and connect the two pins to SN50_v3 as follows:

718

719

* (((

720

One pin to SN50_v3's PA8 pin

721

)))

722

* (((

723

The other pin to SN50_v3's VDD pin

724

)))

725

726

Install the other piece to the door. Find a place where the two pieces will be close to each other when the door is closed. For this particular magnetic sensor, when the door is closed, the output will be short, and PA8 will be at the VCC voltage.

727

728

Door sensors have two types: ** NC (Normal close)** and **NO (normal open)**. The connection for both type sensors are the same. But the decoding for payload are reverse, user need to modify this in the IoT Server decoder.

729

730

When door sensor is shorted, there will extra power consumption in the circuit, the extra current is 3v3/R14 = 3v3/1Mohm = 3uA which can be ignored.

731

732

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379283019-229.png?rev=1.1||alt="1656379283019-229.png"]]

733

734

The above photos shows the two parts of the magnetic switch fitted to a door.

735

736

The software by default uses the falling edge on the signal line as an interrupt. We need to modify it to accept both the rising edge (0v ~-~-> VCC , door close) and the falling edge (VCC ~-~-> 0v , door open) as the interrupt.

The command is:

**AT+INTMOD1=1 **~/~/(more info about INMOD please refer** **[[**AT Command Manual**>>url:http://www.dragino.com/downloads/index.php?dir=LSN50-LoRaST/&file=DRAGINO_LSN50_AT_Commands_v1.5.1.pdf]]**. **)

741

742

Below shows some screen captures in TTN V3:

743

744

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379339508-835.png?rev=1.1||alt="1656379339508-835.png"]]

745

746

In MOD=1, user can use byte 6 to see the status for door open or close. TTN V3 decoder is as below:

747

748

door= (bytes[6] & 0x80)? "CLOSE":"OPEN";

749

750

751

==== 2.3.3.6 I2C Interface (SHT20 & SHT31) ====

752

753

The SDA and SCK are I2C interface lines. You can use these to connect to an I2C device and get the sensor data.

754

755

We have made an example to show how to use the I2C interface to connect to the SHT20/ SHT31 Temperature and Humidity Sensor.

756

757

Notice: Different I2C sensors have different I2C commands set and initiate process, if user want to use other I2C sensors, User need to re-write the source code to support those sensors. SHT20/ SHT31 code in SN50_v3 will be a good reference.

758

759

Below is the connection to SHT20/ SHT31. The connection is as below:

760

761

762

[[image:image-20230513103633-3.png||height="448" width="716"]]

763

764

The device will be able to get the I2C sensor data now and upload to IoT Server.

765

766

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/1656379664142-345.png?rev=1.1||alt="1656379664142-345.png"]]

767

768

Convert the read byte to decimal and divide it by ten.

**Example:**

Temperature: Read:0116(H) = 278(D) Value: 278 /10=27.8℃;

773

774

Humidity: Read:0248(H)=584(D) Value: 584 / 10=58.4, So 58.4%

775

776

If you want to use other I2C device, please refer the SHT20 part source code as reference.

777

778

779

==== 2.3.3.7 Distance Reading ====

780

781

Refer [[Ultrasonic Sensor section>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/#H2.4.8UltrasonicSensor]].

782

783

784

==== 2.3.3.8 Ultrasonic Sensor ====

785

786

This Fundamental Principles of this sensor can be found at this link: [[https:~~/~~/wiki.dfrobot.com/Weather_-_proof_Ultrasonic_Sensor_with_Separate_Probe_SKU~~_~~__SEN0208>>url:https://wiki.dfrobot.com/Weather_-_proof_Ultrasonic_Sensor_with_Separate_Probe_SKU___SEN0208]]

787

788

The SN50_v3 detects the pulse width of the sensor and converts it to mm output. The accuracy will be within 1 centimeter. The usable range (the distance between the ultrasonic probe and the measured object) is between 24cm and 600cm.

789

790

The working principle of this sensor is similar to the **HC-SR04** ultrasonic sensor.

791

792

The picture below shows the connection:

793

794

[[image:image-20230512173903-6.png||height="596" width="715"]]

795

796

Connect to the SN50_v3 and run **AT+MOD=2** to switch to ultrasonic mode (ULT).

797

798

The ultrasonic sensor uses the 8^^th^^ and 9^^th^^ byte for the measurement value.

**Example:**

Distance: Read: 0C2D(Hex) = 3117(D) Value: 3117 mm=311.7 cm

==== 2.3.3.9 Battery Output - BAT pin ====

807

808

The BAT pin of SN50v3 is connected to the Battery directly. If users want to use BAT pin to power an external sensor. User need to make sure the external sensor is of low power consumption. Because the BAT pin is always open. If the external sensor is of high power consumption. the battery of SN50v3-LB will run out very soon.

809

810

811

==== 2.3.3.10 +5V Output ====

812

813

SN50v3 will enable +5V output before all sampling and disable the +5v after all sampling.

814

815

The 5V output time can be controlled by AT Command.

**AT+5VT=1000**

Means set 5V valid time to have 1000ms. So the real 5V output will actually have 1000ms + sampling time for other sensors.

820

821

By default the AT+5VT=500. If the external sensor which require 5v and require more time to get stable state, user can use this command to increase the power ON duration for this sensor.

==== 2.3.3.11 BH1750 Illumination Sensor ====

826

827

MOD=1 support this sensor. The sensor value is in the 8^^th^^ and 9^^th^^ bytes.

828

829

[[image:image-20230512172447-4.png||height="416" width="712"]]

830

831

[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50%20%26%20LSN50-V2%20-%20LoRaWAN%20Sensor%20Node%20User%20Manual/WebHome/image-20220628110012-12.png?rev=1.1||alt="image-20220628110012-12.png" height="361" width="953"]]

832

833

834

==== 2.3.3.12 Working MOD ====

835

836

The working MOD info is contained in the Digital in & Digital Interrupt byte (7^^th^^ Byte).

837

838

User can use the 3^^rd^^ ~~ 7^^th^^ bit of this byte to see the working mod:

839

840

Case 7^^th^^ Byte >> 2 & 0x1f:

* 0: MOD1

* 1: MOD2

* 2: MOD3

* 3: MOD4

* 4: MOD5

* 5: MOD6

* 6: MOD7

* 7: MOD8

* 8: MOD9

== ==

== 2.4 Payload Decoder file ==

855

856

857

In TTN, use can add a custom payload so it shows friendly reading

858

859

In the page (% style="color:#037691" %)**Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder**(%%) to add the decoder from:

860

861

[[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/SN50_v3-LB>>https://github.com/dragino/dragino-end-node-decoder/tree/main/SN50_v3-LB]]

== 2.5 Frequency Plans ==

866

867

868

The SN50v3-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.

869

870

[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]

871

872

873

= 3. Configure SN50v3-LB =

874

875

== 3.1 Configure Methods ==

876

877

878

SN50v3-LB supports below configure method:

879

880

* AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].

881

* AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].

882

* LoRaWAN Downlink. Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.

883

884

== 3.2 General Commands ==

885

886

887

These commands are to configure:

888

889

* General system settings like: uplink interval.

890

* LoRaWAN protocol & radio related command.

891

892

They are same for all Dragino Devices which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:

893

894

[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]

895

896

897

== 3.3 Commands special design for SN50v3-LB ==

898

899

900

These commands only valid for S31x-LB, as below:

901

902

903

=== 3.3.1 Set Transmit Interval Time ===

904

905

Feature: Change LoRaWAN End Node Transmit Interval.

906

907

(% style="color:blue" %)**AT Command: AT+TDC**

908

909

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

910

|=(% style="width: 156px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 137px;background-color:#D9E2F3" %)**Function**|=(% style="background-color:#D9E2F3" %)**Response**

911

|(% style="width:156px" %)AT+TDC=?|(% style="width:137px" %)Show current transmit Interval|(((

912

30000

913

OK

914

the interval is 30000ms = 30s

915

)))

916

|(% style="width:156px" %)AT+TDC=60000|(% style="width:137px" %)Set Transmit Interval|(((

917

OK

918

Set transmit interval to 60000ms = 60 seconds

919

)))

920

921

(% style="color:blue" %)**Downlink Command: 0x01**

922

923

Format: Command Code (0x01) followed by 3 bytes time value.

924

925

If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.

926

927

* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds

928

* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds

=== ===

=== 3.3.2 Get Device Status ===

933

934

Send a LoRaWAN downlink to ask the device to send its status.

935

936

(% style="color:blue" %)**Downlink Payload: **(%%)0x26 01

937

938

Sensor will upload Device Status via FPORT=5. See payload section for detail.

939

940

941

=== 3.3.3 Set Interrupt Mode ===

942

943

Feature, Set Interrupt mode for GPIO_EXIT.

944

945

(% style="color:blue" %)**AT Command: AT+INTMOD1，AT+INTMOD2，AT+INTMOD3**

946

947

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

948

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

949

|(% style="width:154px" %)AT+INTMOD1=?|(% style="width:196px" %)Show current interrupt mode|(% style="width:157px" %)(((

950

0

951

OK

952

the mode is 0 =Disable Interrupt

953

)))

954

|(% style="width:154px" %)AT+INTMOD1=2|(% style="width:196px" %)(((

955

Set Transmit Interval

956

0. (Disable Interrupt),

957

~1. (Trigger by rising and falling edge)

958

2. (Trigger by falling edge)

959

3. (Trigger by rising edge)

960

)))|(% style="width:157px" %)OK

961

|(% style="width:154px" %)AT+INTMOD2=3|(% style="width:196px" %)(((

962

Set Transmit Interval

963

964

trigger by rising edge.

965

)))|(% style="width:157px" %)OK

966

|(% style="width:154px" %)AT+INTMOD3=0|(% style="width:196px" %)Disable Interrupt|(% style="width:157px" %)OK

967

968

(% style="color:blue" %)**Downlink Command: 0x06**

969

970

Format: Command Code (0x06) followed by 3 bytes.

971

972

This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.

973

974

* Example 1: Downlink Payload: 06000000 **~-~-->** AT+INTMOD1=0

975

* Example 2: Downlink Payload: 06000003 **~-~-->** AT+INTMOD1=3

976

* Example 3: Downlink Payload: 06000102 **~-~-->** AT+INTMOD2=2

977

* Example 4: Downlink Payload: 06000201 **~-~-->** AT+INTMOD3=1

=== ===

=== 3.3.4 Set Power Output Duration ===

982

983

Control the output duration 5V . Before each sampling, device will

984

985

~1. first enable the power output to external sensor,

986

987

2. keep it on as per duration, read sensor value and construct uplink payload

988

989

3. final, close the power output.

990

991

(% style="color:blue" %)**AT Command: AT+5VT**

992

993

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

994

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

995

|(% style="width:154px" %)AT+5VT=?|(% style="width:196px" %)Show 5V open time.|(% style="width:157px" %)(((

500(default)

OK

)))

|(% style="width:154px" %)AT+5VT=1000|(% style="width:196px" %)(((

1001

Close after a delay of 1000 milliseconds.

1002

)))|(% style="width:157px" %)OK

1003

1004

(% style="color:blue" %)**Downlink Command: 0x07**

1005

1006

Format: Command Code (0x07) followed by 2 bytes.

1007

1008

The first and second bytes are the time to turn on.

1009

1010

* Example 1: Downlink Payload: 070000 **~-~-->** AT+5VT=0

1011

* Example 2: Downlink Payload: 0701F4 **~-~-->** AT+5VT=500

=== ===

=== 3.3.5 Set Weighing parameters ===

1016

1017

Feature: Working mode 5 is effective, weight initialization and weight factor setting of HX711.

1018

1019

(% style="color:blue" %)**AT Command: AT+WEIGRE,AT+WEIGAP**

1020

1021

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

1022

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

1023

|(% style="width:154px" %)AT+WEIGRE|(% style="width:196px" %)Weight is initialized to 0.|(% style="width:157px" %)OK

1024

|(% style="width:154px" %)AT+WEIGAP=？|(% style="width:196px" %)400.0|(% style="width:157px" %)OK(default)

1025

|(% style="width:154px" %)AT+WEIGAP=400.3|(% style="width:196px" %)Set the factor to 400.3.|(% style="width:157px" %)OK

1026

1027

(% style="color:blue" %)**Downlink Command: 0x08**

1028

1029

Format: Command Code (0x08) followed by 2 bytes or 4 bytes.

1030

1031

Use AT+WEIGRE when the first byte is 1, only 1 byte. When it is 2, use AT+WEIGAP, there are 3 bytes.

1032

1033

The second and third bytes are multiplied by 10 times to be the AT+WEIGAP value.

1034

1035

* Example 1: Downlink Payload: 0801 **~-~-->** AT+WEIGRE

1036

* Example 2: Downlink Payload: 08020FA3 **~-~-->** AT+WEIGAP=400.3

1037

* Example 3: Downlink Payload: 08020FA0 **~-~-->** AT+WEIGAP=400.0

=== ===

=== 3.3.6 Set Digital pulse count value ===

1042

1043

Feature: Set the pulse count value.

1044

1045

Count 1 is PA8 pin of mode 6 and mode 9. Count 2 is PA4 pin of mode 9.

1046

1047

(% style="color:blue" %)**AT Command: AT+SETCNT**

1048

1049

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

1050

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

1051

|(% style="width:154px" %)AT+SETCNT=1,100|(% style="width:196px" %)Initialize the count value 1 to 100.|(% style="width:157px" %)OK

1052

|(% style="width:154px" %)AT+SETCNT=2,0|(% style="width:196px" %)Initialize the count value 2 to 0.|(% style="width:157px" %)OK

1053

1054

(% style="color:blue" %)**Downlink Command: 0x09**

1055

1056

Format: Command Code (0x09) followed by 5 bytes.

1057

1058

The first byte is to select which count value to initialize, and the next four bytes are the count value to be initialized.

1059

1060

* Example 1: Downlink Payload: 090100000000 **~-~-->** AT+SETCNT=1,0

1061

* Example 2: Downlink Payload: 0902000003E8 **~-~-->** AT+SETCNT=2,1000

=== ===

=== 3.3.7 Set Workmode ===

1066

1067

Feature: Switch working mode.

1068

1069

(% style="color:blue" %)**AT Command: AT+MOD**

1070

1071

(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)

1072

|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**

1073

|(% style="width:154px" %)AT+MOD=?|(% style="width:196px" %)Get the current working mode.|(% style="width:157px" %)(((

1074

OK

1075

)))

1076

|(% style="width:154px" %)AT+MOD=4|(% style="width:196px" %)Set the working mode to 3DS18B20s.|(% style="width:157px" %)(((

1077

OK

1078

1079

Attention:Take effect after ATZ

1080

)))

1081

1082

(% style="color:blue" %)**Downlink Command: 0x0A**

1083

1084

Format: Command Code (0x0A) followed by 1 bytes.

1085

1086

* Example 1: Downlink Payload: 0A01 **~-~-->** AT+MOD=1

1087

* Example 2: Downlink Payload: 0A04 **~-~-->** AT+MOD=4

= =

= 4. Battery & Power Consumption =

1092

1093

1094

SN50v3-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.

1095

1096

[[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .

1097

1098

1099

= 5. OTA Firmware update =

1100

1101

1102

(% class="wikigeneratedid" %)

1103

User can change firmware SN50v3-LB to:

1104

1105

* Change Frequency band/ region.

1106

* Update with new features.

1107

* Fix bugs.

1108

1109

Firmware and changelog can be downloaded from : **[[Firmware download link>>url:https://www.dropbox.com/sh/kwqv57tp6pejias/AAAopYMATh1GM6fZ-VRCLrpDa?dl=0]]**

1110

1111

1112

Methods to Update Firmware:

1113

1114

* (Recommanded way) OTA firmware update via wireless: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]

1115

* Update through UART TTL interface.**[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.

= 6. FAQ =

== 6.1 Where can i find source code of SN50v3-LB? ==

1120

1121

* **[[Hardware Source Files>>https://github.com/dragino/Lora/tree/master/LSN50/v3.0]].**

1122

* **[[Software Source Code & Compile instruction>>https://github.com/dragino/SN50v3]].**

= 7. Order Info =

Part Number: (% style="color:blue" %)**SN50v3-LB-XX-YY**

1128

1129

(% style="color:red" %)**XX**(%%): The default frequency band

1130

1131

* (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band

1132

* (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band

1133

* (% style="color:red" %)**EU433**(%%): LoRaWAN EU433 band

1134

* (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band

1135

* (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band

1136

* (% style="color:red" %)**US915**(%%): LoRaWAN US915 band

1137

* (% style="color:red" %)**IN865**(%%): LoRaWAN IN865 band

1138

* (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band

1139

1140

(% style="color:red" %)**YY: ** (%%)Hole Option

1141

1142

* (% style="color:red" %)**12**(%%): With M12 waterproof cable hole

1143

* (% style="color:red" %)**16**(%%): With M16 waterproof cable hole

1144

* (% style="color:red" %)**20**(%%): With M20 waterproof cable hole

1145

* (% style="color:red" %)**NH**(%%): No Hole

= 8. Packing Info =

(% style="color:#037691" %)**Package Includes**:

1150

1151

* SN50v3-LB LoRaWAN Generic Node

1152

1153

(% style="color:#037691" %)**Dimension and weight**:

* Device Size: cm

* Device Weight: g

* Package Size / pcs : cm

* Weight / pcs : g

= 9. Support =

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

1164

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.cc>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.cc]]

Wiki source code of SN50v3-LB LoRaWAN Sensor Node User Manual

Applications

Navigation