SDI-12-LB -- SDI-12 to LoRaWAN Converter User Manual

SDI-12 (Serial Digital Interface at 1200 baud) is an asynchronous [[serial communications>>url:https://en.wikipedia.org/wiki/Serial_communication]] protocol for intelligent sensors that monitor environment data. SDI-12 protocol is widely used in Agriculture sensor and Weather Station sensors.

27

28

**SDI-12-LB** has SDI-12 interface and support 12v output to power external SDI-12 sensor. It can get the environment data from SDI-12 sensor and sends out the data via LoRaWAN wireless protocol.

29

30

The LoRa wireless technology used in **SDI-12-LB** allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.

31

32

**SDI-12-LB** is powered by **8500mAh Li-SOCI2 battery**, it is designed for long term use up to 5 years.

33

34

Each **SDI-12-LB** is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.

35

36

37

[[image:image-20230201084414-1.png||height="464" width="1108"]]

== 1.2 Features ==

* LoRaWAN 1.0.3 Class A

48

* Ultra-low power consumption

49

* Controllable 5v and 12v output to power external sensor

50

* SDI-12 Protocol to connect to SDI-12 Sensor

51

* Monitor Battery Level

52

* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865

53

* Support Bluetooth v5.1 and LoRaWAN remote configure.

54

* Support wireless OTA update firmware

55

* Uplink on periodically

56

* Downlink to change configure

57

* 8500mAh Battery for long term use

58

59

== 1.3 Specification ==

60

61

62

**Micro Controller:**

* MCU: 48Mhz ARM

* Flash: 256KB

* RAM: 64KB

**Common DC Characteristics:**

69

70

* Supply Voltage: 2.5v ~~ 3.6v

71

* Operating Temperature: -40 ~~ 85°C

**LoRa Spec:**

* Frequency Range, Band 1 (HF): 862 ~~ 1020 Mhz

76

* Max +22 dBm constant RF output vs.

77

* RX sensitivity: down to -139 dBm.

78

* Excellent blocking immunity

79

80

**Current Input Measuring :**

* Range: 0 ~~ 20mA

* Accuracy: 0.02mA

* Resolution: 0.001mA

85

86

**Voltage Input Measuring:**

* Range: 0 ~~ 30v

* Accuracy: 0.02v

* Resolution: 0.001v

**Battery:**

* Li/SOCI2 un-chargeable battery

95

* Capacity: 8500mAh

96

* Self-Discharge: <1% / Year @ 25°C

97

* Max continuously current: 130mA

98

* Max boost current: 2A, 1 second

99

100

**Power Consumption**

101

102

* Sleep Mode: 5uA @ 3.3v

103

* LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm

104

105

== 1.4 Connect to SDI-12 Sensor ==

[[image:1675212538524-889.png]]

110

111

112

== 1.5 Sleep mode and working mode ==

113

114

115

**Deep Sleep Mode: **Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.

116

117

**Working Mode: **In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.

118

119

120

== 1.6 Button & LEDs ==

121

122

123

[[image:1675212633011-651.png]]

(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)

128

|=(% style="width: 167px;" %)**Behavior on ACT**|=(% style="width: 117px;" %)**Function**|=(% style="width: 225px;" %)**Action**

129

|(% style="width:167px" %)Pressing ACT between 1s < time < 3s|(% style="width:117px" %)Send an uplink|(% style="width:225px" %)(((

130

If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, (% style="color:blue" %)**blue led** (%%)will blink once.

131

Meanwhile, BLE module will be active and user can connect via BLE to configure device.

132

)))

133

|(% style="width:167px" %)Pressing ACT for more than 3s|(% style="width:117px" %)Active Device|(% style="width:225px" %)(((

134

(% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:#037691" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network.

135

(% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.

136

Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device join or not join LoRaWAN network.

137

)))

138

|(% style="width:167px" %)Fast press ACT 5 times.|(% style="width:117px" %)Deactivate Device|(% style="width:225px" %)(% style="color:red" %)**Red led**(%%) will solid on for 5 seconds. Means PS-LB is in Deep Sleep Mode.

139

140

== 1.7 Pin Mapping ==

141

142

143

[[image:1675213198663-754.png]]

144

145

146

== 1.8 BLE connection ==

147

148

149

SDI-12-LB support BLE remote configure.

150

151

BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:

152

153

* Press button to send an uplink

154

* Press button to active device.

155

* Device Power on or reset.

156

157

If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.

== 1.9 Mechanical ==

[[image:image-20230201090139-2.png]]

167

168

[[image:image-20230201090139-3.png]]

169

170

[[image:image-20230201090139-4.png]]

171

172

173

= 2. Configure SDI-12 to connect to LoRaWAN network =

174

175

== 2.1 How it works ==

176

177

178

The SDI-12-LB is configured as **LoRaWAN OTAA Class A** mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and activate the SDI-12-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.

179

180

181

== 2.2 Quick guide to connect to LoRaWAN server (OTAA) ==

182

183

184

Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.

185

186

187

[[image:image-20230201090528-5.png||height="465" width="1111"]]

188

189

190

The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.

191

192

193

**Step 1**: Create a device in TTN with the OTAA keys from SDI-12-LB.

194

195

Each SDI-12-LB is shipped with a sticker with the default device EUI as below:

196

197

198

[[image:image-20230131134744-2.jpeg]]

You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:

205

206

207

**Register the device**

208

209

[[image:1675213652444-622.png]]

210

211

212

**Add APP EUI and DEV EUI**

213

214

215

[[image:1675213661769-223.png]]

216

217

218

**Add APP EUI in the application**

219

220

221

[[image:1675213675852-577.png]]

**Add APP KEY**

[[image:1675213686734-883.png]]

227

228

229

**Step 2**: Activate on SDI-12-LB

230

231

232

Press the button for 5 seconds to activate the SDI-12-LB.

233

234

235

**Green led** will fast blink 5 times, device will enter **OTA mode** for 3 seconds. And then start to JOIN LoRaWAN network. **Green led** will solidly turn on for 5 seconds after joined in network.

236

237

238

[[image:1675213704414-644.png]]

239

240

241

== 2.3 SDI-12 Related Commands ==

242

243

244

User need to configure SDI-12-LB to communicate with SDI-12 sensors otherwise the uplink payload will only include a few bytes.

245

246

247

=== 2.3.1 Basic SDI-12 debug command ===

248

249

250

User can run some basic SDI-12 command to debug the connection to the SDI-12 sensor. These commands can be sent via AT Command or LoRaWAN downlink command.

251

252

If SDI-12 sensor return value after get these commands, //SDI-12-LB// will uplink the return on FPORT=100, otherwise, if there is no response from SDI-12 sensor. //SDI-12-LB// will uplink NULL (0x 4E 55 4C 4C) to server.

253

254

The following is the display information on the serial port and the server.

[[image:image-20230201091027-6.png]]

259

260

261

[[image:image-20230201091027-7.png||height="261" width="1179"]]

262

263

264

==== **al! ~-~- Get SDI-12 sensor Identification** ====

265

266

267

* AT Command: AT+ADDRI=aa

268

* LoRaWAN Downlink(prefix 0xAA00): AA 00 aa

269

270

**Parameter: **aa: ASCII value of SDI-12 sensor address in downlink or HEX value in AT Command)

271

272

**Example : **AT+ADDRI=0 ( Equal to downlink: 0x AA 00 30)

273

274

275

The following is the display information on the serial port and the server.

276

277

278

[[image:image-20230201091257-8.png]]

279

280

281

[[image:image-20230201091257-9.png||height="225" width="1242"]]

282

283

284

==== **aM!,aMC!, aM1!- aM9!, aMC1!- aMC9!** ====

285

286

287

**aM! **: Start Non-Concurrent Measurement

288

289

**aMC! **: Start Non-Concurrent Measurement – Request CRC

290

291

**aM1!- aM9! **: Additional Measurements

292

293

**aMC1!- aMC9!** : Additional Measurements – Request CRC

294

295

296

* AT Command : AT+ADDRM=0,1,0,1

297

* LoRaWAN Downlink(prefix 0xAA01): 0xAA 01 30 01 00 01

298

299

Downlink：AA 01 aa bb cc dd

300

301

**aa**: SDI-12 sensor address.

302

303

**bb**: 0: no CRC, 1: request CRC

304

305

**cc**: 1-9: Additional Measurement, 0: no additional measurement

306

307

**dd**: delay (in second) to send **aD0!** to get return.

308

309

310

The following is the display information on the serial port and the server.

311

312

313

[[image:image-20230201091630-10.png]]

314

315

316

[[image:image-20230201091630-11.png||height="247" width="1165"]]

==== **aC!, aCC!, aC1!- aC9!, aCC1!- aCC9! ** ====

321

322

323

**aC!** : Start Concurrent Measurement

324

325

**aCC!** : Start Concurrent Measurement – Request CRC

326

327

**aC1!- aC9!** : Start Additional Concurrent Measurements

328

329

**aCC1!- aCC9!** : Start Additional Concurrent Measurements – Request CRC

330

331

332

* AT Command : AT+ADDRC=0,1,0,1

333

334

* LoRaWAN Downlink(0xAA02): 0xAA 02 30 01 00 01

335

336

Downlink: AA 02 aa bb cc dd

337

338

**aa**: SDI-12 sensor address.

339

340

**bb**: 0: no CRC, 1: request CRC

341

342

**cc**: 1-9: Additional Measurement, 0: no additional measurement

343

344

**dd**: delay (in second) to send **aD0!** to get return.

345

346

347

The following is the display information on the serial port and the server.

348

349

350

[[image:image-20230201091954-12.png]]

351

352

353

[[image:image-20230201091954-13.png||height="203" width="1117"]]

354

355

356

(% style="display:none" %) (%%)

357

358

==== **aR0!- aR9!, aRC0!- aRC9!** ====

359

360

361

Start Continuous Measurement

362

363

Start Continuous Measurement – Request CRC

364

365

366

* AT Command : AT+ADDRR=0,1,0,1

367

* LoRaWAN Downlink (0xAA 03): 0xAA 03 30 01 00 01

368

369

Downlink: AA 03 aa bb cc dd

370

371

**aa**: SDI-12 sensor address.

372

373

**bb**: 0: no CRC, 1: request CRC

374

375

**cc**: 1-9: Additional Measurement, 0: no additional measurement

376

377

**dd**: delay (in second) to send **aD0!** to get return.

378

379

380

The following is the display information on the serial port and the server.

[[image:image-20230201092208-14.png]]

385

386

387

[[image:image-20230201092208-15.png||height="214" width="1140"]]

388

389

390

=== 2.3.2 Advance SDI-12 Debug command ===

391

392

393

This command can be used to debug all SDI-12 command.

394

395

396

LoRaWAN Downlink: A8 aa xx xx xx xx bb cc

397

398

**aa **: total SDI-12 command length

399

400

**xx **: SDI-12 command

401

402

**bb **: Delay to wait for return

403

404

**cc **: 0: don't uplink return to LoRaWAN, 1: Uplink return to LoRaWAN on FPORT=100

405

406

407

**Example: **AT+CFGDEV =0RC0!,1

408

409

**0RC0! **: SDI-12 Command,

410

411

**1 **: Delay 1 second. ( 0: 810 mini-second)

412

413

Equal Downlink: 0xA8 05 30 52 43 30 21 01 01

414

415

416

The following is the display information on the serial port and the server.

417

418

419

[[image:image-20230201092355-16.png]]

420

421

422

[[image:image-20230201092355-17.png||height="426" width="1135"]]

=== 2.3.3 Convert ASCII to String ===

428

429

430

This command is used to convert between ASCII and String format.

431

432

AT+CONVFORM ( Max length: 80 bytes)

**Example:**

1) AT+CONVFORM=0, string Convert String from String to ASCII

438

439

[[image:1675214845056-885.png]]

440

441

442

2) AT+CONVFORM=1, ASCII Convert ASCII to String.

443

444

[[image:1675214856590-846.png]]

=== 2.3.4 Define periodically SDI-12 commands and uplink. ===

452

453

454

AT+COMMANDx & AT+DATACUTx

455

456

User can define max 15 SDI-12 Commands (AT+COMMAND1 ~~ AT+COMMANDF). On each uplink period (TDC time, default 20 minutes), SDI-12-LB will send these SDI-12 commands and wait for return from SDI-12 sensors. SDI-12-LB will then combine these returns and uplink via LoRaWAN.

* ** AT Command:**

**AT+COMMANDx=var1,var2,var3,var4.**

462

463

**var1**: SDI-12 command , for example: 0RC0!

464

465

**var2**: Wait timeout for return. (unit: second)

466

467

**var3**: Whether to send //addrD0!// to get return after var2 timeout. 0: Don't Send //addrD0! //; 1: Send //addrD0!//.

468

469

**var4**: validation check for return. If return invalid, SDI-12-LB will resend this command. Max 2 retries.

470

471

**0 ** No validation check;

472

473

**1** Check if return chars are printable char(0x20 ~~ 0x7E);

474

475

**2** Check if there is return from SDI-12 sensor

476

477

**3** Check if return pass CRC check ( SDI-12 command var1 must include CRC request);

478

479

480

Each AT+COMMANDx is followed by a **AT+DATACUT** command. AT+DATACUT command is used to take the useful string from the SDI-12 sensor so the final payload will have the minimum length to uplink.

481

482

483

**AT+DATACUTx** : This command defines how to handle the return from AT+COMMANDx, max return length is 100 bytes.

484

485

(% border="1" style="background-color:#f7faff; width:436px" %)

486

|(% style="width:433px" %)(((

487

**AT+DATACUTx=a,b,c**

488

489

**a**: length for the return of AT+COMMAND

490

491

**b**: 1: grab valid value by byte, max 6 bytes. 2: grab valid value by bytes section, max 3 sections.

492

493

**c**: define the position for valid value.

494

)))

495

496

For example, if return from AT+COMMAND1 is “013METER TER12 112T12-00024895” , Below AT+DATACUT1 will get different result to combine payload:

497

498

499

(% border="1" cellspacing="4" style="background-color:#f7faff; width:510px" %)

500

|(% style="width:170px" %)**AT+DATACUT1 value**|(% style="width:338px" %)**Final Result to combine Payload**

501

|(% style="width:170px" %)34,1,1+2+3|(% style="width:338px" %)0D 00 01 30 31 33

502

|(% style="width:170px" %)34,2,1~~8+12~~16|(% style="width:338px" %)0D 00 01 30 31 33 4D 45 54 45 52 54 45 52 31 32

503

|(% style="width:170px" %)34,2,1~~34|(% style="width:338px" %)0D 00 01 30 31 33 4D 45 54 45 52 20 20 20 54 45 52 31 32 20 31 31 32 54 31 32 2D 30 30 30 32 34 38 39 35 0D 0A

504

505

* ** Downlink Payload:**

506

507

**0xAF** downlink command can be used to set AT+COMMANDx or AT+DATACUTx.

508

509

510

**Note : if user use AT+COMMANDx to add a new command, he also need to send AT+DATACUTx downlink.**

511

512

513

Format: ** AF MM NN LL XX XX XX XX YY**

Where:

* **MM **: the AT+COMMAND or AT+DATACUT to be set. Value from 01 ~~ 0F,

518

* **NN **: 1: set the AT+DATACUT value ; 2: set the AT+DATACUT value.

519

* **LL **: The length of AT+COMMAND or AT+DATACUT command

520

* **XX XX XX XX **: AT+COMMAND or AT+DATACUT command

521

* **YY **: If YY=0, RS485-LN will execute the downlink command without uplink; if YY=1, RS485-LN will execute an uplink after got this command.

**Example:**

[[image:image-20230201094129-18.png]]

527

528

529

**Clear SDI12 Command**

530

531

The AT+COMMANDx and AT+DATACUTx settings are stored in special location, user can use below command to clear them.

* ** AT Command:**

**~ AT+CMDEAR=mm,nn** mm: start position of erase ,nn: stop position of erase

537

538

539

Etc. AT+CMDEAR=1,10 means erase AT+COMMAND1/AT+DATACUT1 to AT+COMMAND10/AT+DATACUT10

540

541

542

* ** Downlink Payload:**

543

544

**~ 0x09 aa bb** same as AT+CMDEAR=aa,bb

**command combination**

549

550

Below shows a screen shot how the results combines together to a uplink payload.

551

552

[[image:1675215745275-920.png]]

553

554

555

If user don't want to use DATACUT for some command, he simply want to uplink all returns. AT+ALLDATAMOD can be set to 1.

556

557

**AT+ALLDATAMOD** will simply get all return and don’t do CRC check as result for SDI-12 command. AT+DATACUTx command has higher priority, if AT+DATACUTx has been set, AT+ALLDATAMOD will be ignore for this SDI-12 command.

558

559

560

**For example: ** as below photo, AT+ALLDATAMOD=1, but AT+DATACUT1 has been set, AT+DATACUT1 will be still effect the result.

561

562

563

[[image:1675215782925-448.png]]

564

565

566

If AT+ALLDATAMOD=1, **FX,X** will be added in the payload, FX specify which command is used and X specify the length of return. for example in above screen, F1 05 means the return is from AT+COMMAND1 and the return is 5 bytes.

**Compose Uplink**

**AT+DATAUP=0**

Compose the uplink payload with value returns in sequence and send with A SIGNLE UPLINK.

575

576

Final Payload is Battery Info+PAYVER + VALID Value from RETURN1 + Valid Value from RETURN2 + … + RETURNx

577

578

Where PAYVER is defined by AT+PAYVER, below is an example screen shot.

579

580

581

[[image:1675215828102-844.png]]

**AT+DATAUP=1**

Compose the uplink payload with value returns in sequence and send with Multiply UPLINKs.

Final Payload is

__**Battery Info+PAYVER + PAYLOAD COUNT + PAYLOAD# + DATA**__

591

592

1. Battery Info (2 bytes): Battery voltage

593

1. PAYVER (1 byte): Defined by AT+PAYVER

594

1. PAYLOAD COUNT (1 byte): Total how many uplinks of this sampling.

595

1. PAYLOAD# (1 byte): Number of this uplink. (from 0,1,2,3…,to PAYLOAD COUNT)

596

1. DATA: Valid value: max 6 bytes(US915 version here, Notice*!) for each uplink so each uplink <= 11 bytes. For the last uplink, DATA will might less than 6 bytes

597

598

[[image:1675215848113-696.png]]

599

600

601

**Notice: the Max bytes is according to the max support bytes in different Frequency Bands for lowest SF. As below:**

602

603

* For AU915/AS923 bands, if UplinkDwell time=0, max 51 bytes for each uplink ( so 51 -5 = 46 max valid date)

604

* For AU915/AS923 bands, if UplinkDwell time=1, max 11 bytes for each uplink ( so 11 -5 = 6 max valid date).

605

* For US915 band, max 11 bytes for each uplink ( so 11 -5 = 6 max valid date).

606

* For all other bands: max 51 bytes for each uplink ( so 51 -5 = 46 max valid date).

607

608

**~ When AT+DATAUP=1, the maximum number of segments is 15, and the maximum total number of bytes is 1500;**

609

610

**~ When AT+DATAUP=1 and AT+ADR=0, the maximum number of bytes of each payload is determined by the DR value.**

611

612

613

== 2.4 Uplink Payload ==

614

615

616

Uplink payloads have two types:

617

618

* Distance Value: Use FPORT=2

619

* Other control commands: Use other FPORT fields.

620

621

The application server should parse the correct value based on FPORT settings.

622

623

624

2.4.1 Device Payload, FPORT=5

625

626

Include device configure status. Once SDI-12-LB Joined the network, it will uplink this message to the server.

627

628

629

Users can also use the downlink command(0x26 01) to ask SDI-12-LB to resend this uplink.

630

631

632

(% border="1" cellspacing="4" style="background-color:#f7faff; width:437px" %)

633

|(% colspan="6" style="width:434px" %)**Device Status (FPORT=5)**

Example parse in TTNv3

638

639

[[image:1675215946738-635.png]]

640

641

**Sensor Model**: For SDI-12-LB, this value is 0x17

642

643

**Firmware Version**: 0x0100, Means: v1.0.0 version

**Frequency Band**:

*0x01: EU868

*0x02: US915

*0x03: IN865

*0x04: AU915

*0x05: KZ865

*0x06: RU864

*0x07: AS923

*0x08: AS923-1

*0x09: AS923-2

*0x0a: AS923-3

*0x0b: CN470

*0x0c: EU433

*0x0d: KR920

*0x0e: MA869

**Sub-Band**:

AU915 and US915:value 0x00 ~~ 0x08

679

680

CN470: value 0x0B ~~ 0x0C

681

682

Other Bands: Always 0x00

**Battery Info**:

Check the battery voltage.

Ex1: 0x0B45 = 2885mV

Ex2: 0x0B49 = 2889mV

1.

11.

111. Uplink Payload, FPORT=2

697

698

There are different cases for uplink. See below

699

700

* SDI-12 Debug Command return: FPORT=100

701

702

* Periodically Uplink: FPORT=2

|(((

**Size**

**(bytes)**

)))|**2**|**1**|**Length depends on the return from the commands**

|**Value**|(((

Battery(mV)

&

Interrupt_Flag

)))|[[PAYLOAD_VER>>path:#Probe_Model]]|(((

716

If the valid payload is too long and exceed the maximum support

717

718

Payload length in server,server will show payload not provided in the LoRaWAN server.

719

)))

720

721

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image034.png]]

1.

11.

111. Battery Info

Check the battery voltage for SDI-12-LB.

Ex1: 0x0B45 = 2885mV

Ex2: 0x0B49 = 2889mV

1.

11.

111. Interrupt Pin

This data field shows if this packet is generated by **Interrupt Pin** or not. [[Click here>>path:#Int_mod]] for the hardware and software set up. Note: The Internet Pin is a separate pin in the screw terminal. See [[pin mapping>>path:#pins]].

Example:

Ex1: 0x0B45:0x0B&0x80= 0x00 Normal uplink packet.

746

747

Ex2: 0x8B49:0x8B&0x80= 0x80 Interrupt Uplink Packet.

1.

11.

111. Payload version

1.

11.

111. Decode payload in The Things Network

761

762

While using TTN network, you can add the payload format to decode the payload.

763

764

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image035.png]]

765

766

767

There is no fix payload decoder in LoRaWAN server because the SDI-12 sensors returns are different. User need to write the decoder themselves for their case.

下面的解码生成超链接放进去.

function Decoder(bytes, port) {

if(port==5)

{

var freq_band;

var sub_band;

var sensor;

if(bytes[0]==0x17)

sensor= "SDI12-LB";

var firm_ver= (bytes[1]&0x0f)+'.'+(bytes[2]>>4&0x0f)+'.'+(bytes[2]&0x0f);

if(bytes[3]==0x01)

freq_band="EU868";

else if(bytes[3]==0x02)

freq_band="US915";

else if(bytes[3]==0x03)

freq_band="IN865";

else if(bytes[3]==0x04)

freq_band="AU915";

else if(bytes[3]==0x05)

freq_band="KZ865";

else if(bytes[3]==0x06)

freq_band="RU864";

else if(bytes[3]==0x07)

freq_band="AS923";

else if(bytes[3]==0x08)

freq_band="AS923_1";

else if(bytes[3]==0x09)

freq_band="AS923_2";

else if(bytes[3]==0x0A)

freq_band="AS923_3";

else if(bytes[3]==0x0F)

freq_band="AS923_4";

else if(bytes[3]==0x0B)

freq_band="CN470";

else if(bytes[3]==0x0C)

freq_band="EU433";

else if(bytes[3]==0x0D)

freq_band="KR920";

else if(bytes[3]==0x0E)

freq_band="MA869";

if(bytes[4]==0xff)

sub_band="NULL";

else

sub_band=bytes[4];

var bat= (bytes[5]<<8 | bytes[6])/1000;

return {

SENSOR_MODEL:sensor,

FIRMWARE_VERSION:firm_ver,

871

872

FREQUENCY_BAND:freq_band,

SUB_BAND:sub_band,

BAT:bat,

}

}

else if(port==100)

{

var datas_sum={};

for(var j=0;j<bytes.length;j++)

{

var datas= String.fromCharCode(bytes[j]);

if(j=='0')

datas_sum.datas_sum=datas;

else

datas_sum.datas_sum+=datas;

}

return datas_sum;

}

else

{

var decode={};

decode.EXTI_Trigger= (bytes[0] & 0x80)? "TRUE":"FALSE";

916

917

decode.BatV= ((bytes[0]<<8 | bytes[1])&0x7FFF)/1000;

918

919

decode.Payver= bytes[2];

920

921

for(var i=3;i<bytes.length;i++)

{

var data= String.fromCharCode(bytes[i]);

if(i=='3')

decode.data_sum=data;

else

decode.data_sum+=data;

}

return decode;

}

}

1.

11. Uplink Interval

The SDI-12-LB by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link:

949

950

[[http:~~/~~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands#Change_Uplink_Interval>>url:http://wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands#Change_Uplink_Interval]]

1.

11. Frequency Plans

The SDI12-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.

958

959

960

[[https:~~/~~/wiki.dragino.com/index.php?title=End_Device_Frequency_Band>>url:https://wiki.dragino.com/index.php?title=End_Device_Frequency_Band]]

1.

11. Firmware Change Log

966

967

**Firmware download link:**

968

969

[[https:~~/~~/www.dropbox.com/sh/gf1glloczbzz19h/AABbuYI4WY6VdAmpXo6o1V2Ka?dl=0>>url:https://www.dropbox.com/sh/gf1glloczbzz19h/AABbuYI4WY6VdAmpXo6o1V2Ka?dl=0]]

1. Configure SDI-12-LB via AT Command or LoRaWAN Downlink

974

975

Use can configure SDI-12-LB via AT Command or LoRaWAN Downlink.

976

977

* AT Command Connection: See [[FAQ>>path:#AT_COMMAND]].

978

* LoRaWAN Downlink instruction for different platforms:

979

980

[[http:~~/~~/wiki.dragino.com/index.php?title=Main_Page#Use_Note_for_Server>>url:http://wiki.dragino.com/index.php?title=Main_Page#Use_Note_for_Server]]

981

982

983

There are two kinds of commands to configure SDI-12-LB, they are:

984

985

* **General Commands**.

986

987

These commands are to configure:

988

989

* General system settings like: uplink interval.

990

* LoRaWAN protocol & radio related command.

991

992

They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:

993

994

[[http:~~/~~/wiki.dragino.com/index.php?title=End_Device_Downlink_Command>>url:http://wiki.dragino.com/index.php?title=End_Device_Downlink_Command]]

995

996

997

* **Commands special design for SDI-12-LB**

998

999

These commands only valid for SDI-12-LB, as below:

1.

11. Set Transmit Interval Time

1005

1006

Feature: Change LoRaWAN End Node Transmit Interval.

1007

1008

**AT Command: AT+TDC**

1009

1010

|**Command Example**|**Function**|**Response**

1011

|AT+TDC=?|Show current transmit Interval|(((

30000

OK

the interval is 30000ms = 30s

1017

)))

1018

|AT+TDC=60000|Set Transmit Interval|(((

1019

OK

1020

1021

Set transmit interval to 60000ms = 60 seconds

1022

)))

1023

1024

**Downlink Command: 0x01**

1025

1026

Format: Command Code (0x01) followed by 3 bytes time value.

1027

1028

If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.

1029

1030

* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds

1031

* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds

1032

1033

1.

1034

11. Set Interrupt Mode

1035

1036

Feature, Set Interrupt mode for GPIO_EXIT.

1037

1038

**AT Command: AT+INTMOD**

1039

1040

|**Command Example**|**Function**|**Response**

1041

|AT+INTMOD=?|Show current interrupt mode|(((

0

OK

the mode is 0 = No interruption

1047

)))

1048

|AT+INTMOD=2|(((

1049

Set Transmit Interval

1050

1051

1. (Disable Interrupt),

1052

1. (Trigger by rising and falling edge),

1053

1. (Trigger by falling edge)

1054

1. (Trigger by rising edge)

1055

)))|OK

1056

1057

**Downlink Command: 0x06**

1058

1059

Format: Command Code (0x06) followed by 3 bytes.

1060

1061

This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.

1062

1063

* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode

1064

* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger

1065

1066

1.

1067

11. Set the output time

1068

1069

Feature, Control the output 3V3 , 5V or 12V.

1070

1071

**AT Command: AT+3V3T**

1072

1073

|**Command Example**|**Function**|**Response**

1074

|AT+3V3T=?|Show 3V3 open time.|(((

0

OK

)))

|AT+3V3T=0|Normally open 3V3 power supply.|(((

OK

default setting

)))

|AT+3V3T=1000|Close after a delay of 1000 milliseconds.|(((

OK

)))

|AT+3V3T=65535|Normally closed 3V3 power supply.|(((

OK

)))

**AT Command: AT+5VT**

1096

1097

|**Command Example**|**Function**|**Response**

1098

|AT+5VT=?|Show 5V open time.|(((

0

OK

)))

|AT+5VT=0|Normally closed 5V power supply.|(((

OK

default setting

)))

|AT+5VT=1000|Close after a delay of 1000 milliseconds.|(((

OK

)))

|AT+5VT=65535|Normally open 5V power supply.|(((

OK

)))

**AT Command: AT+12VT**

1120

1121

|**Command Example**|**Function**|**Response**

1122

|AT+12VT=?|Show 12V open time.|(((

0

OK

)))

|AT+12VT=0|Normally closed 12V power supply.|OK

1128

|AT+12VT=500|Close after a delay of 500 milliseconds.|(((

OK

)))

**Downlink Command: 0x07**

1135

1136

Format: Command Code (0x07) followed by 3 bytes.

1137

1138

The first byte is which power, the second and third bytes are the time to turn on.

1139

1140

* Example 1: Downlink Payload: 070101F4 -> AT+3V3T=500

1141

* Example 2: Downlink Payload: 0701FFFF -> AT+3V3T=65535

1142

* Example 3: Downlink Payload: 070203E8 -> AT+5VT=1000

1143

* Example 4: Downlink Payload: 07020000 -> AT+5VT=0

1144

* Example 5: Downlink Payload: 070301F4 -> AT+12VT=500

1145

* Example 6: Downlink Payload: 07030000 -> AT+12VT=0

1146

1147

1.

1148

11. Set the all data mode

1149

1150

Feature, Set the all data mode.

1151

1152

**AT Command: AT+ALLDATAMOD**

1153

1154

|**Command Example**|**Function**|**Response**

1155

|AT+ALLDATAMOD=?|Show current all data mode|(((

0

OK

)))

|AT+ALLDATAMOD=1|Set all data mode is 1.|OK

1162

1163

**Downlink Command: 0xAB**

1164

1165

Format: Command Code (0xAB) followed by 1 bytes.

1166

1167

* Example 1: Downlink Payload: AB 00 ~/~/ AT+ALLDATAMOD=0

1168

* Example 2: Downlink Payload: AB 01 ~/~/ AT+ALLDATAMOD=1

1169

1170

1.

1171

11. Set the splicing payload for uplink

1172

1173

Feature, splicing payload for uplink.

1174

1175

**AT Command: AT+DATAUP**

1176

1177

|**Command Example**|**Function**|**Response**

1178

|AT+DATAUP =?|Show current splicing payload for uplink mode|(((

0

OK

)))

|AT+DATAUP =0|(((

Set splicing payload for uplink mode is 0.

)))|(((

OK

)))

|AT+DATAUP =1|Set splicing payload for uplink mode is 1 , and the each splice uplink is sent sequentially.|OK

1194

|AT+DATAUP =1,20000|(((

1195

Set splicing payload for uplink mode is 1, and the uplink interval of each splice to 20000 milliseconds.

)))|OK

**Downlink Command: 0xAD**

1201

1202

Format: Command Code (0xAD) followed by 1 bytes or 5 bytes.

1203

1204

* Example 1: Downlink Payload: AD 00 ~/~/ AT+DATAUP=0

1205

* Example 2: Downlink Payload: AD 01 ~/~/ AT+DATAUP =1

1206

* Example 3: Downlink Payload: AD 01 00 00 14~/~/ AT+DATAUP =1,20000

1207

1208

This means that the interval is set to 0x000014=20S

1.

11. Set the payload version

1213

1214

Feature, Set the payload version.

1215

1216

**AT Command: AT+PAYVER**

1217

1218

|**Command Example**|**Function**|**Response**

1219

|AT+PAYVER=?|Show current payload version|(((

1

OK

)))

|AT+PAYVER=5|Set payload version is 5.|OK

1226

1227

**Downlink Command: 0xAE**

1228

1229

Format: Command Code (0xAE) followed by 1 bytes.

1230

1231

* Example 1: Downlink Payload: AE 01 ~/~/ AT+PAYVER=1

1232

* Example 2: Downlink Payload: AE 05 ~/~/ AT+PAYVER=5

1233

1234

1. Battery & how to replace

1235

11. Battery Type

1236

1237

SDI-12-LB is equipped with a [[8500mAH ER26500 Li-SOCI2 battery>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]. The battery is un-rechargeable battery with low discharge rate targeting for 8~~10 years use. This type of battery is commonly used in IoT target for long-term running, such as water meter.

1238

1239

1240

The discharge curve is not linear so can’t simply use percentage to show the battery level. Below is the battery performance.

1241

1242

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image036.png]]

1243

1244

1245

Minimum Working Voltage for the SDI-12-LB:

1246

1247

SDI-12-LB: 2.45v ~~ 3.6v

1.

11. Replace Battery

Any battery with range 2.45 ~~ 3.6v can be a replacement. We recommend to use Li-SOCl2 Battery.

1254

1255

And make sure the positive and negative pins match.

1.

11. Power Consumption Analyze

1261

1262

Dragino Battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.

1263

1264

1265

Instruction to use as below:

1266

1267

1268

Step 1: Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from:

1269

1270

[[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/]]

1271

1272

1273

Step 2: Open it and choose

* Product Model

* Uplink Interval

* Working Mode

And the Life expectation in difference case will be shown on the right.

1280

1281

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image037.png]]

1282

1283

1284

The battery related documents as below:

1285

1286

* [[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/&file=LSN50-Battery-Dimension.pdf]],

1287

* [[Lithium-Thionyl Chloride Battery>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/ER18505_datasheet-EN.pdf]] datasheet, [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/ER18505_datasheet_PM-ER18505-S-02-LF_EN.pdf]]

1288

* [[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC_1520_datasheet.jpg]], [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC1520%20Technical%20Specification20171123.pdf]]

|(((

JST-XH-2P connector

)))

[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image038.png]]

1.

11.

111. Battery Note

The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.

1.

11.

111. Replace the battery

1308

1309

You can change the battery in the SDI-12-LB.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.

1310

1311

1312

The default battery pack of SDI-12-LB includes a ER26500 plus super capacitor. If user can’t find this pack locally, they can find ER26500 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)

1. Remote Configure device

1320

11. Connect via BLE

1321

1322

Please see this instruction for how to configure via BLE:

1323

1324

[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]]

1.

11. AT Command Set

1. OTA firmware update

1331

1332

Please see this link for how to do OTA firmware update.

1333

1334

[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]

1. Order Info

**Package Includes**:

1349

1350

* SDI-12-LB SDI-12 to LoRaWAN Converter

1351

1352

**Dimension and weight**:

* Device Size: cm

* Device Weight: g

* Package Size / pcs : cm

* Weight / pcs : g

1. Support

* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.

1364

* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to

1365

1366

[[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]

1367

1368

Wiki source code of SDI-12-LB -- SDI-12 to LoRaWAN Converter User Manual