Wiki source code of SDI-12-LB -- SDI-12 to LoRaWAN Converter User Manual

Version 28.1 by Xiaoling on 2023/02/01 09:27

version	line-number	content
2.2	1	(% style="text-align:center" %)
	2	[[image:image-20230131183542-1.jpeg\|\|height="694" width="694"]]
	3
	4	Table of Contents：
	5
	6
	7
	8
	9
	10
	11
	12
	13
	14
	15
	16
	17
	18
9.2	19	= 1. Introduction =
2.2	20
9.2	21	== 1.1 What is SDI-12 to LoRaWAN Converter ==
2.2	22
	23
9.2	24	The Dragino SDI-12-LB is a SDI-12 to LoRaWAN Converter designed for Smart Agriculture solution.
	25
2.2	26	SDI-12 (Serial Digital Interface at 1200 baud) is an asynchronous [[serial communications>>url:https://en.wikipedia.org/wiki/Serial_communication]] protocol for intelligent sensors that monitor environment data. SDI-12 protocol is widely used in Agriculture sensor and Weather Station sensors.
	27
	28	SDI-12-LB has SDI-12 interface and support 12v output to power external SDI-12 sensor. It can get the environment data from SDI-12 sensor and sends out the data via LoRaWAN wireless protocol.
	29
	30	The LoRa wireless technology used in SDI-12-LB allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
	31
	32	SDI-12-LB is powered by 8500mAh Li-SOCI2 battery, it is designed for long term use up to 5 years.
	33
	34	Each SDI-12-LB is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
	35
	36
9.2	37	[[image:image-20230201084414-1.png\|\|height="464" width="1108"]]
2.2	38
	39
	40
	41
	42
	43
9.2	44	== 1.2 Features ==
	45
	46
2.2	47	* LoRaWAN 1.0.3 Class A
	48	* Ultra-low power consumption
	49	* Controllable 5v and 12v output to power external sensor
	50	* SDI-12 Protocol to connect to SDI-12 Sensor
	51	* Monitor Battery Level
	52	* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
	53	* Support Bluetooth v5.1 and LoRaWAN remote configure.
	54	* Support wireless OTA update firmware
	55	* Uplink on periodically
	56	* Downlink to change configure
	57	* 8500mAh Battery for long term use
	58
9.2	59	== 1.3 Specification ==
2.2	60
	61
	62	Micro Controller:
	63
	64	* MCU: 48Mhz ARM
	65	* Flash: 256KB
	66	* RAM: 64KB
	67
	68	Common DC Characteristics:
	69
	70	* Supply Voltage: 2.5v ~~ 3.6v
	71	* Operating Temperature: -40 ~~ 85°C
	72
	73	LoRa Spec:
	74
	75	* Frequency Range, Band 1 (HF): 862 ~~ 1020 Mhz
	76	* Max +22 dBm constant RF output vs.
	77	* RX sensitivity: down to -139 dBm.
	78	* Excellent blocking immunity
	79
	80	Current Input Measuring :
	81
	82	* Range: 0 ~~ 20mA
	83	* Accuracy: 0.02mA
	84	* Resolution: 0.001mA
	85
	86	Voltage Input Measuring:
	87
	88	* Range: 0 ~~ 30v
	89	* Accuracy: 0.02v
	90	* Resolution: 0.001v
	91
	92	Battery:
	93
	94	* Li/SOCI2 un-chargeable battery
	95	* Capacity: 8500mAh
	96	* Self-Discharge: <1% / Year @ 25°C
	97	* Max continuously current: 130mA
	98	* Max boost current: 2A, 1 second
	99
	100	Power Consumption
	101
	102	* Sleep Mode: 5uA @ 3.3v
	103	* LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm
	104
9.2	105	== 1.4 Connect to SDI-12 Sensor ==
2.2	106
	107
	108
9.2	109	[[image:1675212538524-889.png]]
2.2	110
	111
9.2	112	== 1.5 Sleep mode and working mode ==
2.2	113
	114
9.2	115	Deep Sleep Mode: Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.
2.2	116
9.2	117	Working Mode: In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.
2.2	118
	119
9.2	120	== 1.6 Button & LEDs ==
2.2	121
	122
9.2	123	[[image:1675212633011-651.png]]
2.2	124
	125
	126
9.2	127	(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)
	128	\|=(% style="width: 167px;" %)Behavior on ACT\|=(% style="width: 117px;" %)Function\|=(% style="width: 225px;" %)Action
	129	\|(% style="width:167px" %)Pressing ACT between 1s < time < 3s\|(% style="width:117px" %)Send an uplink\|(% style="width:225px" %)(((
	130	If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, (% style="color:blue" %)blue led (%%)will blink once.
2.2	131	Meanwhile, BLE module will be active and user can connect via BLE to configure device.
	132	)))
9.2	133	\|(% style="width:167px" %)Pressing ACT for more than 3s\|(% style="width:117px" %)Active Device\|(% style="width:225px" %)(((
	134	(% style="color:green" %)Green led(%%) will fast blink 5 times, device will enter (% style="color:#037691" %)OTA mode(%%) for 3 seconds. And then start to JOIN LoRaWAN network.
	135	(% style="color:green" %)Green led(%%) will solidly turn on for 5 seconds after joined in network.
2.2	136	Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device join or not join LoRaWAN network.
	137	)))
9.2	138	\|(% style="width:167px" %)Fast press ACT 5 times.\|(% style="width:117px" %)Deactivate Device\|(% style="width:225px" %)(% style="color:red" %)Red led(%%) will solid on for 5 seconds. Means PS-LB is in Deep Sleep Mode.
2.2	139
9.2	140	== 1.7 Pin Mapping ==
2.2	141
	142
9.2	143	[[image:1675213198663-754.png]]
2.2	144
	145
9.2	146	== 1.8 BLE connection ==
2.2	147
9.2	148
2.2	149	SDI-12-LB support BLE remote configure.
	150
	151	BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:
	152
	153	* Press button to send an uplink
	154	* Press button to active device.
	155	* Device Power on or reset.
	156
	157	If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.
	158
	159
9.2	160	== 1.9 Mechanical ==
2.2	161
	162
	163
	164
	165
9.2	166	[[image:image-20230201090139-2.png]]
2.2	167
9.2	168	[[image:image-20230201090139-3.png]]
2.2	169
9.2	170	[[image:image-20230201090139-4.png]]
2.2	171
	172
19.2	173	= 2. Configure SDI-12 to connect to LoRaWAN network =
9.2	174
19.2	175	== 2.1 How it works ==
9.2	176
	177
19.2	178	The SDI-12-LB is configured as LoRaWAN OTAA Class A mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and activate the SDI-12-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
9.2	179
2.2	180
19.2	181	== 2.2 Quick guide to connect to LoRaWAN server (OTAA) ==
2.2	182
	183
	184	Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.
	185
	186
19.2	187	[[image:image-20230201090528-5.png\|\|height="465" width="1111"]]
2.2	188
	189
	190	The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
	191
	192
	193	Step 1: Create a device in TTN with the OTAA keys from SDI-12-LB.
	194
	195	Each SDI-12-LB is shipped with a sticker with the default device EUI as below:
	196
	197
19.2	198	[[image:image-20230131134744-2.jpeg]]
2.2	199
	200
	201
	202
	203
	204	You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
	205
	206
	207	Register the device
	208
19.2	209	[[image:1675213652444-622.png]]
2.2	210
	211
	212	Add APP EUI and DEV EUI
	213
	214
19.2	215	[[image:1675213661769-223.png]]
2.2	216
	217
	218	Add APP EUI in the application
	219
	220
19.2	221	[[image:1675213675852-577.png]]
2.2	222
	223
	224	Add APP KEY
	225
19.2	226	[[image:1675213686734-883.png]]
2.2	227
	228
	229	Step 2: Activate on SDI-12-LB
	230
	231
	232	Press the button for 5 seconds to activate the SDI-12-LB.
	233
	234
	235	Green led will fast blink 5 times, device will enter OTA mode for 3 seconds. And then start to JOIN LoRaWAN network. Green led will solidly turn on for 5 seconds after joined in network.
	236
	237
19.2	238	[[image:1675213704414-644.png]]
2.2	239
	240
19.2	241	== 2.3 SDI-12 Related Commands ==
2.2	242
	243
19.2	244	User need to configure SDI-12-LB to communicate with SDI-12 sensors otherwise the uplink payload will only include a few bytes.
2.2	245
	246
27.2	247	=== 2.3.1 Basic SDI-12 debug command ===
2.2	248
	249
	250	User can run some basic SDI-12 command to debug the connection to the SDI-12 sensor. These commands can be sent via AT Command or LoRaWAN downlink command.
	251
	252	If SDI-12 sensor return value after get these commands, //SDI-12-LB// will uplink the return on FPORT=100, otherwise, if there is no response from SDI-12 sensor. //SDI-12-LB// will uplink NULL (0x 4E 55 4C 4C) to server.
	253
	254	The following is the display information on the serial port and the server.
	255
	256
	257
19.2	258	[[image:image-20230201091027-6.png]]
2.2	259
19.2	260
	261	[[image:image-20230201091027-7.png\|\|height="261" width="1179"]]
	262
	263
	264	==== al! ~-~- Get SDI-12 sensor Identification ====
	265
	266
2.2	267	* AT Command: AT+ADDRI=aa
	268	* LoRaWAN Downlink(prefix 0xAA00): AA 00 aa
	269
19.2	270	Parameter: aa: ASCII value of SDI-12 sensor address in downlink or HEX value in AT Command)
2.2	271
19.2	272	Example : AT+ADDRI=0 ( Equal to downlink: 0x AA 00 30)
2.2	273
	274
	275	The following is the display information on the serial port and the server.
	276
	277
19.2	278	[[image:image-20230201091257-8.png]]
2.2	279
	280
19.2	281	[[image:image-20230201091257-9.png\|\|height="225" width="1242"]]
	282
	283
27.2	284	==== aM!,aMC!, aM1!- aM9!, aMC1!- aMC9! ====
2.2	285
	286
27.2	287	aM! : Start Non-Concurrent Measurement
2.2	288
27.2	289	aMC! : Start Non-Concurrent Measurement – Request CRC
2.2	290
27.2	291	aM1!- aM9! : Additional Measurements
2.2	292
27.2	293	aMC1!- aMC9! : Additional Measurements – Request CRC
2.2	294
27.2	295
2.2	296	* AT Command : AT+ADDRM=0,1,0,1
	297	* LoRaWAN Downlink(prefix 0xAA01): 0xAA 01 30 01 00 01
	298
	299	Downlink：AA 01 aa bb cc dd
	300
27.2	301	aa: SDI-12 sensor address.
2.2	302
27.2	303	bb: 0: no CRC, 1: request CRC
2.2	304
27.2	305	cc: 1-9: Additional Measurement, 0: no additional measurement
2.2	306
27.2	307	dd: delay (in second) to send aD0! to get return.
2.2	308
	309
	310	The following is the display information on the serial port and the server.
	311
	312
27.2	313	[[image:image-20230201091630-10.png]]
2.2	314
	315
27.2	316	[[image:image-20230201091630-11.png\|\|height="247" width="1165"]]
2.2	317
	318
	319
27.2	320	==== aC!, aCC!, aC1!- aC9!, aCC1!- aCC9! ====
2.2	321
	322
27.2	323	aC! : Start Concurrent Measurement
2.2	324
27.2	325	aCC! : Start Concurrent Measurement – Request CRC
2.2	326
27.2	327	aC1!- aC9! : Start Additional Concurrent Measurements
	328
	329	aCC1!- aCC9! : Start Additional Concurrent Measurements – Request CRC
	330
	331
2.2	332	* AT Command : AT+ADDRC=0,1,0,1
	333
	334	* LoRaWAN Downlink(0xAA02): 0xAA 02 30 01 00 01
	335
	336	Downlink: AA 02 aa bb cc dd
	337
27.2	338	aa: SDI-12 sensor address.
2.2	339
27.2	340	bb: 0: no CRC, 1: request CRC
2.2	341
27.2	342	cc: 1-9: Additional Measurement, 0: no additional measurement
2.2	343
27.2	344	dd: delay (in second) to send aD0! to get return.
2.2	345
	346
	347	The following is the display information on the serial port and the server.
	348
	349
27.2	350	[[image:image-20230201091954-12.png]]
2.2	351
	352
27.2	353	[[image:image-20230201091954-13.png\|\|height="203" width="1117"]]
2.2	354
27.2	355
	356	(% style="display:none" %) (%%)
	357
	358	==== aR0!- aR9!, aRC0!- aRC9! ====
	359
	360
2.2	361	Start Continuous Measurement
	362
	363	Start Continuous Measurement – Request CRC
	364
	365
	366	* AT Command : AT+ADDRR=0,1,0,1
	367	* LoRaWAN Downlink (0xAA 03): 0xAA 03 30 01 00 01
	368
	369	Downlink: AA 03 aa bb cc dd
	370
27.2	371	aa: SDI-12 sensor address.
2.2	372
27.2	373	bb: 0: no CRC, 1: request CRC
2.2	374
27.2	375	cc: 1-9: Additional Measurement, 0: no additional measurement
2.2	376
27.2	377	dd: delay (in second) to send aD0! to get return.
2.2	378
	379
	380	The following is the display information on the serial port and the server.
	381
	382
	383
27.2	384	[[image:image-20230201092208-14.png]]
2.2	385
27.2	386
	387	[[image:image-20230201092208-15.png\|\|height="214" width="1140"]]
	388
	389
	390	=== 2.3.2 Advance SDI-12 Debug command ===
	391
	392
2.2	393	This command can be used to debug all SDI-12 command.
	394
	395
	396	LoRaWAN Downlink: A8 aa xx xx xx xx bb cc
	397
27.2	398	aa : total SDI-12 command length
2.2	399
27.2	400	xx : SDI-12 command
2.2	401
27.2	402	bb : Delay to wait for return
2.2	403
27.2	404	cc : 0: don't uplink return to LoRaWAN, 1: Uplink return to LoRaWAN on FPORT=100
2.2	405
	406
27.2	407	Example: AT+CFGDEV =0RC0!,1
2.2	408
27.2	409	0RC0! : SDI-12 Command,
2.2	410
27.2	411	1 : Delay 1 second. ( 0: 810 mini-second)
2.2	412
	413	Equal Downlink: 0xA8 05 30 52 43 30 21 01 01
	414
	415
	416	The following is the display information on the serial port and the server.
	417
	418
27.2	419	[[image:image-20230201092355-16.png]]
2.2	420
	421
27.2	422	[[image:image-20230201092355-17.png\|\|height="426" width="1135"]]
	423
9.2	424	1.
2.2	425	11.
	426	111. Convert ASCII to String
	427
	428	This command is used to convert between ASCII and String format.
	429
	430
	431	AT+CONVFORM ( Max length: 80 bytes)
	432
	433	Example:
	434
	435	1)AT+CONVFORM=0,string Convert String from String to ASCII
	436
	437	[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image027.png]]
	438
	439
	440	2)AT+CONVFORM=1,ASCII Convert ASCII to String.
	441
	442	[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image028.png]]
	443
	444
	445
9.2	446	1.
2.2	447	11.
	448	111. Define periodically SDI-12 commands and uplink.
	449
	450	AT+COMMANDx & AT+DATACUTx
	451
	452	User can define max 15 SDI-12 Commands (AT+COMMAND1 ~~ AT+COMMANDF). On each uplink period (TDC time, default 20 minutes), SDI-12-LB will send these SDI-12 commands and wait for return from SDI-12 sensors. SDI-12-LB will then combine these returns and uplink via LoRaWAN.
	453
	454
	455	* AT Command:
	456
	457	AT+COMMANDx=var1,var2,var3,var4.
	458
	459	var1: SDI-12 command , for example: 0RC0!
	460
	461	var2: Wait timeout for return. (unit: second)
	462
	463	var3: Whether to send //addrD0!// to get return after var2 timeout. 0: Don’t Send //addrD0!//; 1: Send //addrD0!//.
	464
	465	var4: validation check for return. If return invalid, SDI-12-LB will resend this command. Max 2 retries.
	466
	467	0 No validation check;
	468
	469	1 Check if return chars are printable char(0x20 ~~ 0x7E);
	470
	471	2 Check if there is return from SDI-12 sensor
	472
	473	3 Check if return pass CRC check ( SDI-12 command var1 must include CRC request);
	474
	475
	476	Each AT+COMMANDx is followed by a AT+DATACUT command. AT+DATACUT command is used to take the useful string from the SDI-12 sensor so the final payload will have the minimum length to uplink.
	477
	478
	479	AT+DATACUTx : This command defines how to handle the return from AT+COMMANDx, max return length is 100 bytes.
	480
	481	\|(((
	482	AT+DATACUTx=a,b,c
	483
	484	a: length for the return of AT+COMMAND
	485
	486	b:1: grab valid value by byte, max 6 bytes. 2: grab valid value by bytes section, max 3 sections.
	487
	488	c: define the position for valid value.
	489	)))
	490
	491	For example, if return from AT+COMMAND1 is “013METER TER12 112T12-00024895” ,. Below AT+DATACUT1 will get different result to combine payload:
	492
	493
	494	\|AT+DATACUT1 value\|Final Result to combine Payload
	495	\|34,1,1+2+3\|0D 00 01 30 31 33
	496	\|34,2,1~~8+12~~16\|0D 00 01 30 31 33 4D 45 54 45 52 54 45 52 31 32
	497	\|34,2,1~~34\|0D 00 01 30 31 33 4D 45 54 45 52 20 20 20 54 45 52 31 32 20 31 31 32 54 31 32 2D 30 30 30 32 34 38 39 35 0D 0A
	498
	499	* Downlink Payload:
	500
	501	0xAF downlink command can be used to set AT+COMMANDx or AT+DATACUTx.
	502
	503
	504	Note : if user use AT+COMMANDx to add a new command, he also need to send AT+DATACUTx downlink.
	505
	506
	507	Format: AF MM NN LL XX XX XX XX YY
	508
	509	Where:
	510
	511	* MM: the AT+COMMAND or AT+DATACUT to be set. Value from 01 ~~ 0F,
	512	* NN: 1: set the AT+DATACUT value ; 2: set the AT+DATACUT value.
	513	* LL: The length of AT+COMMAND or AT+DATACUT command
	514	* XX XX XX XX: AT+COMMAND or AT+DATACUT command
	515	* YY: If YY=0, RS485-LN will execute the downlink command without uplink; if YY=1, RS485-LN will execute an uplink after got this command.
	516
	517	Example:
	518
9.2	519	AF 03 01 07 30 4D 43 21 01 01 01 00: Same as AT+COMMAND3=0MC!, 1, 1, 1
2.2	520
	521	AF 03 02 06 10 01 05 06 09 0A 00: Same as AT+DATACUT3=16,1,5+6+9+10
	522
	523	AF 03 02 06 0B 02 05 07 08 0A 00: Same as AT+DATACUT3=11,2,5~~7+8~~10
	524
	525
	526	Clear SDI12 Command
	527
	528	The AT+COMMANDx and AT+DATACUTx settings are stored in special location, user can use below command to clear them.
	529
	530
	531	* AT Command:
	532
	533	~ AT+CMDEAR=mm,nn mm: start position of erase ,nn: stop position of erase
	534
	535
	536	Etc. AT+CMDEAR=1,10 means erase AT+COMMAND1/AT+DATACUT1 to AT+COMMAND10/AT+DATACUT10
	537
	538
	539	* Downlink Payload:
	540
	541	~ 0x09 aa bb same as AT+CMDEAR=aa,bb
	542
	543
	544
	545
	546	command combination
	547
	548	Below shows a screen shot how the results combines together to a uplink payload.
	549
	550	[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image029.png]]
	551
	552
	553	If user don’t want to use DATACUT for some command, he simply want to uplink all returns. AT+ALLDATAMOD can be set to 1.
	554
	555	AT+ALLDATAMOD will simply get all return and don’t do CRC check as result for SDI-12 command. AT+DATACUTx command has higher priority, if AT+DATACUTx has been set, AT+ALLDATAMOD will be ignore for this SDI-12 command.
	556
	557
	558	For example: as below photo, AT+ALLDATAMOD=1, but AT+DATACUT1 has been set, AT+DATACUT1 will be still effect the result.
	559
	560
	561	[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image030.png]]
	562
	563
	564	If AT+ALLDATAMOD=1, FX,X will be added in the payload, FX specify which command is used and X specify the length of return. for example in above screen, F1 05 means the return is from AT+COMMAND1 and the return is 5 bytes.
	565
	566
	567
	568	Compose Uplink
	569
	570	AT+DATAUP=0
	571
	572	Compose the uplink payload with value returns in sequence and send with A SIGNLE UPLINK.
	573
	574	Final Payload is Battery Info+PAYVER + VALID Value from RETURN1 + Valid Value from RETURN2 + … + RETURNx
	575
	576	Where PAYVER is defined by AT+PAYVER, below is an example screen shot.
	577
	578
	579	[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image031.png]]
	580
	581
	582	AT+DATAUP=1
	583
	584	Compose the uplink payload with value returns in sequence and send with Multiply UPLINKs.
	585
	586	Final Payload is
	587
	588	Battery Info+PAYVER + PAYLOAD COUNT + PAYLOAD# + DATA
	589
	590	1. Battery Info (2 bytes): Battery voltage
	591	1. PAYVER (1 byte): Defined by AT+PAYVER
	592	1. PAYLOAD COUNT (1 byte): Total how many uplinks of this sampling.
	593	1. PAYLOAD# (1 byte): Number of this uplink. (from 0,1,2,3…,to PAYLOAD COUNT)
	594	1. DATA: Valid value: max 6 bytes(US915 version here, Notice*!) for each uplink so each uplink <= 11 bytes. For the last uplink, DATA will might less than 6 bytes
	595
	596	[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image032.png]]
	597
	598
	599	Notice: the Max bytes is according to the max support bytes in different Frequency Bands for lowest SF. As below:
	600
	601	~* For AU915/AS923 bands, if UplinkDwell time=0, max 51 bytes for each uplink ( so 51 -5 = 46 max valid date)
	602
	603	* For AU915/AS923 bands, if UplinkDwell time=1, max 11 bytes for each uplink ( so 11 -5 = 6 max valid date).
	604
	605	* For US915 band, max 11 bytes for each uplink ( so 11 -5 = 6 max valid date).
	606
	607	~* For all other bands: max 51 bytes for each uplink ( so 51 -5 = 46 max valid date).
	608
	609	* When AT+DATAUP=1, the maximum number of segments is 15, and the maximum total number of bytes is 1500;
	610
	611	~ When AT+DATAUP=1 and AT+ADR=0, the maximum number of bytes of each payload is determined by the DR value.
	612
	613	1.
	614	11. Uplink Payload
	615
	616	Uplink payloads have two types:
	617
	618	* Distance Value: Use FPORT=2
	619	* Other control commands: Use other FPORT fields.
	620
	621	The application server should parse the correct value based on FPORT settings.
	622
	623
	624	1.
	625	11.
	626	111. Device Payload, FPORT=5
	627
	628	Include device configure status. Once SDI-12-LB Joined the network, it will uplink this message to the server.
	629
	630
	631	Users can also use the downlink command(0x26 01) to ask SDI-12-LB to resend this uplink.
	632
	633
	634	\|(% colspan="6" %)Device Status (FPORT=5)
	635	\|Size (bytes)\|1\|2\|1\|1\|2
	636	\|Value\|Sensor Model\|Firmware Version\|Frequency Band\|Sub-band\|BAT
	637
	638	Example parse in TTNv3
	639
	640	[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image033.png]]
	641
	642	Sensor Model: For SDI-12-LB, this value is 0x17
	643
	644	Firmware Version: 0x0100, Means: v1.0.0 version
	645
	646	Frequency Band:
	647
	648	*0x01: EU868
	649
	650	*0x02: US915
	651
	652	*0x03: IN865
	653
	654	*0x04: AU915
	655
	656	*0x05: KZ865
	657
	658	*0x06: RU864
	659
	660	*0x07: AS923
	661
	662	*0x08: AS923-1
	663
	664	*0x09: AS923-2
	665
	666	*0x0a: AS923-3
	667
	668	*0x0b: CN470
	669
	670	*0x0c: EU433
	671
	672	*0x0d: KR920
	673
	674	*0x0e: MA869
	675
	676
	677	Sub-Band:
	678
	679	AU915 and US915:value 0x00 ~~ 0x08
	680
	681	CN470: value 0x0B ~~ 0x0C
	682
	683	Other Bands: Always 0x00
	684
	685
	686	Battery Info:
	687
	688	Check the battery voltage.
	689
	690	Ex1: 0x0B45 = 2885mV
	691
	692	Ex2: 0x0B49 = 2889mV
	693
	694
	695	1.
	696	11.
	697	111. Uplink Payload, FPORT=2
	698
	699	There are different cases for uplink. See below
	700
	701	* SDI-12 Debug Command return: FPORT=100
	702
	703	* Periodically Uplink: FPORT=2
	704
	705	\|(((
	706	Size
	707
	708	(bytes)
	709	)))\|2\|1\|Length depends on the return from the commands
	710	\|Value\|(((
	711	Battery(mV)
	712
	713	&
	714
	715	Interrupt_Flag
	716	)))\|[[PAYLOAD_VER>>path:#Probe_Model]]\|(((
	717	If the valid payload is too long and exceed the maximum support
	718
	719	Payload length in server,server will show payload not provided in the LoRaWAN server.
	720	)))
	721
	722	[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image034.png]]
	723
	724
	725
9.2	726	1.
2.2	727	11.
	728	111. Battery Info
	729
	730	Check the battery voltage for SDI-12-LB.
	731
	732	Ex1: 0x0B45 = 2885mV
	733
	734	Ex2: 0x0B49 = 2889mV
	735
	736
	737	1.
	738	11.
	739	111. Interrupt Pin
	740
	741	This data field shows if this packet is generated by Interrupt Pin or not. [[Click here>>path:#Int_mod]] for the hardware and software set up. Note: The Internet Pin is a separate pin in the screw terminal. See [[pin mapping>>path:#pins]].
	742
	743
	744	Example:
	745
	746	Ex1: 0x0B45:0x0B&0x80= 0x00 Normal uplink packet.
	747
	748	Ex2: 0x8B49:0x8B&0x80= 0x80 Interrupt Uplink Packet.
	749
	750
	751	1.
	752	11.
	753	111. Payload version
	754
	755
	756
	757
	758
	759	1.
	760	11.
	761	111. Decode payload in The Things Network
	762
	763	While using TTN network, you can add the payload format to decode the payload.
	764
	765	[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image035.png]]
	766
	767
	768	There is no fix payload decoder in LoRaWAN server because the SDI-12 sensors returns are different. User need to write the decoder themselves for their case.
	769
	770
	771	下面的解码生成超链接放进去.
	772
	773	function Decoder(bytes, port) {
	774
	775	if(port==5)
	776
	777	{
	778
	779	var freq_band;
	780
	781	var sub_band;
	782
	783	var sensor;
	784
	785
	786	if(bytes[0]==0x17)
	787
	788	sensor= "SDI12-LB";
	789
	790
	791	var firm_ver= (bytes[1]&0x0f)+'.'+(bytes[2]>>4&0x0f)+'.'+(bytes[2]&0x0f);
	792
	793
	794	if(bytes[3]==0x01)
	795
	796	freq_band="EU868";
	797
	798	else if(bytes[3]==0x02)
	799
	800	freq_band="US915";
	801
	802	else if(bytes[3]==0x03)
	803
	804	freq_band="IN865";
	805
	806	else if(bytes[3]==0x04)
	807
	808	freq_band="AU915";
	809
	810	else if(bytes[3]==0x05)
	811
	812	freq_band="KZ865";
	813
	814	else if(bytes[3]==0x06)
	815
	816	freq_band="RU864";
	817
	818	else if(bytes[3]==0x07)
	819
	820	freq_band="AS923";
	821
	822	else if(bytes[3]==0x08)
	823
	824	freq_band="AS923_1";
	825
	826	else if(bytes[3]==0x09)
	827
	828	freq_band="AS923_2";
	829
	830	else if(bytes[3]==0x0A)
	831
	832	freq_band="AS923_3";
	833
	834	else if(bytes[3]==0x0F)
	835
	836	freq_band="AS923_4";
	837
	838	else if(bytes[3]==0x0B)
	839
	840	freq_band="CN470";
	841
	842	else if(bytes[3]==0x0C)
	843
	844	freq_band="EU433";
	845
	846	else if(bytes[3]==0x0D)
	847
	848	freq_band="KR920";
	849
	850	else if(bytes[3]==0x0E)
	851
	852	freq_band="MA869";
	853
	854
	855	if(bytes[4]==0xff)
	856
	857	sub_band="NULL";
	858
	859	else
	860
	861	sub_band=bytes[4];
	862
	863
	864	var bat= (bytes[5]<<8 \| bytes[6])/1000;
	865
	866
	867	return {
	868
	869	SENSOR_MODEL:sensor,
	870
	871	FIRMWARE_VERSION:firm_ver,
	872
	873	FREQUENCY_BAND:freq_band,
	874
	875	SUB_BAND:sub_band,
	876
	877	BAT:bat,
	878
	879	}
	880
	881	}
	882
	883	else if(port==100)
	884
	885	{
	886
	887	var datas_sum={};
	888
	889	for(var j=0;j<bytes.length;j++)
	890
	891	{
	892
	893	var datas= String.fromCharCode(bytes[j]);
	894
	895	if(j=='0')
	896
	897	datas_sum.datas_sum=datas;
	898
	899	else
	900
	901	datas_sum.datas_sum+=datas;
	902
	903	}
	904
	905
	906	return datas_sum;
	907
	908	}
	909
	910	else
	911
	912	{
	913
	914	var decode={};
	915
	916	decode.EXTI_Trigger= (bytes[0] & 0x80)? "TRUE":"FALSE";
	917
	918	decode.BatV= ((bytes[0]<<8 \| bytes[1])&0x7FFF)/1000;
	919
	920	decode.Payver= bytes[2];
	921
	922	for(var i=3;i<bytes.length;i++)
	923
	924	{
	925
	926	var data= String.fromCharCode(bytes[i]);
	927
	928	if(i=='3')
	929
	930	decode.data_sum=data;
	931
	932	else
	933
	934	decode.data_sum+=data;
	935
	936	}
	937
	938	return decode;
	939
	940	}
	941
	942
	943	}
	944
	945
	946	1.
	947	11. Uplink Interval
	948
	949	The SDI-12-LB by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link:
	950
	951	[[http:~~/~~/wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands#Change_Uplink_Interval>>url:http://wiki.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands#Change_Uplink_Interval]]
	952
	953
	954
	955	1.
	956	11. Frequency Plans
	957
	958	The SDI12-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
	959
	960
	961	[[https:~~/~~/wiki.dragino.com/index.php?title=End_Device_Frequency_Band>>url:https://wiki.dragino.com/index.php?title=End_Device_Frequency_Band]]
	962
	963
	964
	965	1.
	966	11. Firmware Change Log
	967
	968	Firmware download link:
	969
	970	[[https:~~/~~/www.dropbox.com/sh/gf1glloczbzz19h/AABbuYI4WY6VdAmpXo6o1V2Ka?dl=0>>url:https://www.dropbox.com/sh/gf1glloczbzz19h/AABbuYI4WY6VdAmpXo6o1V2Ka?dl=0]]
	971
	972
	973
	974	1. Configure SDI-12-LB via AT Command or LoRaWAN Downlink
	975
	976	Use can configure SDI-12-LB via AT Command or LoRaWAN Downlink.
	977
	978	* AT Command Connection: See [[FAQ>>path:#AT_COMMAND]].
	979	* LoRaWAN Downlink instruction for different platforms:
	980
	981	[[http:~~/~~/wiki.dragino.com/index.php?title=Main_Page#Use_Note_for_Server>>url:http://wiki.dragino.com/index.php?title=Main_Page#Use_Note_for_Server]]
	982
	983
	984	There are two kinds of commands to configure SDI-12-LB, they are:
	985
	986	* General Commands.
	987
	988	These commands are to configure:
	989
	990	* General system settings like: uplink interval.
	991	* LoRaWAN protocol & radio related command.
	992
	993	They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:
	994
	995	[[http:~~/~~/wiki.dragino.com/index.php?title=End_Device_Downlink_Command>>url:http://wiki.dragino.com/index.php?title=End_Device_Downlink_Command]]
	996
	997
	998	* Commands special design for SDI-12-LB
	999
	1000	These commands only valid for SDI-12-LB, as below:
	1001
	1002
	1003
	1004	1.
	1005	11. Set Transmit Interval Time
	1006
	1007	Feature: Change LoRaWAN End Node Transmit Interval.
	1008
	1009	AT Command: AT+TDC
	1010
	1011	\|Command Example\|Function\|Response
	1012	\|AT+TDC=?\|Show current transmit Interval\|(((
	1013	30000
	1014
	1015	OK
	1016
	1017	the interval is 30000ms = 30s
	1018	)))
	1019	\|AT+TDC=60000\|Set Transmit Interval\|(((
	1020	OK
	1021
	1022	Set transmit interval to 60000ms = 60 seconds
	1023	)))
	1024
	1025	Downlink Command: 0x01
	1026
	1027	Format: Command Code (0x01) followed by 3 bytes time value.
	1028
	1029	If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
	1030
	1031	* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
	1032	* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
	1033
	1034	1.
	1035	11. Set Interrupt Mode
	1036
	1037	Feature, Set Interrupt mode for GPIO_EXIT.
	1038
	1039	AT Command: AT+INTMOD
	1040
	1041	\|Command Example\|Function\|Response
	1042	\|AT+INTMOD=?\|Show current interrupt mode\|(((
	1043	0
	1044
	1045	OK
	1046
	1047	the mode is 0 = No interruption
	1048	)))
	1049	\|AT+INTMOD=2\|(((
	1050	Set Transmit Interval
	1051
	1052	1. (Disable Interrupt),
	1053	1. (Trigger by rising and falling edge),
	1054	1. (Trigger by falling edge)
	1055	1. (Trigger by rising edge)
	1056	)))\|OK
	1057
	1058	Downlink Command: 0x06
	1059
	1060	Format: Command Code (0x06) followed by 3 bytes.
	1061
	1062	This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
	1063
	1064	* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
	1065	* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
	1066
	1067	1.
	1068	11. Set the output time
	1069
	1070	Feature, Control the output 3V3 , 5V or 12V.
	1071
	1072	AT Command: AT+3V3T
	1073
	1074	\|Command Example\|Function\|Response
	1075	\|AT+3V3T=?\|Show 3V3 open time.\|(((
	1076	0
	1077
	1078	OK
	1079	)))
	1080	\|AT+3V3T=0\|Normally open 3V3 power supply.\|(((
	1081	OK
	1082
	1083	default setting
	1084	)))
	1085	\|AT+3V3T=1000\|Close after a delay of 1000 milliseconds.\|(((
	1086	OK
	1087
	1088
	1089	)))
	1090	\|AT+3V3T=65535\|Normally closed 3V3 power supply.\|(((
	1091	OK
	1092
	1093
	1094	)))
	1095
	1096	AT Command: AT+5VT
	1097
	1098	\|Command Example\|Function\|Response
	1099	\|AT+5VT=?\|Show 5V open time.\|(((
	1100	0
	1101
	1102	OK
	1103	)))
	1104	\|AT+5VT=0\|Normally closed 5V power supply.\|(((
	1105	OK
	1106
	1107	default setting
	1108	)))
	1109	\|AT+5VT=1000\|Close after a delay of 1000 milliseconds.\|(((
	1110	OK
	1111
	1112
	1113	)))
	1114	\|AT+5VT=65535\|Normally open 5V power supply.\|(((
	1115	OK
	1116
	1117
	1118	)))
	1119
	1120	AT Command: AT+12VT
	1121
	1122	\|Command Example\|Function\|Response
	1123	\|AT+12VT=?\|Show 12V open time.\|(((
	1124	0
	1125
	1126	OK
	1127	)))
	1128	\|AT+12VT=0\|Normally closed 12V power supply.\|OK
	1129	\|AT+12VT=500\|Close after a delay of 500 milliseconds.\|(((
	1130	OK
	1131
	1132
	1133	)))
	1134
	1135	Downlink Command: 0x07
	1136
	1137	Format: Command Code (0x07) followed by 3 bytes.
	1138
	1139	The first byte is which power, the second and third bytes are the time to turn on.
	1140
	1141	* Example 1: Downlink Payload: 070101F4 -> AT+3V3T=500
	1142	* Example 2: Downlink Payload: 0701FFFF -> AT+3V3T=65535
	1143	* Example 3: Downlink Payload: 070203E8 -> AT+5VT=1000
	1144	* Example 4: Downlink Payload: 07020000 -> AT+5VT=0
	1145	* Example 5: Downlink Payload: 070301F4 -> AT+12VT=500
	1146	* Example 6: Downlink Payload: 07030000 -> AT+12VT=0
	1147
	1148	1.
	1149	11. Set the all data mode
	1150
	1151	Feature, Set the all data mode.
	1152
	1153	AT Command: AT+ALLDATAMOD
	1154
	1155	\|Command Example\|Function\|Response
	1156	\|AT+ALLDATAMOD=?\|Show current all data mode\|(((
	1157	0
	1158
	1159
	1160	OK
	1161	)))
	1162	\|AT+ALLDATAMOD=1\|Set all data mode is 1.\|OK
	1163
	1164	Downlink Command: 0xAB
	1165
	1166	Format: Command Code (0xAB) followed by 1 bytes.
	1167
	1168	* Example 1: Downlink Payload: AB 00 ~/~/ AT+ALLDATAMOD=0
	1169	* Example 2: Downlink Payload: AB 01 ~/~/ AT+ALLDATAMOD=1
	1170
	1171	1.
	1172	11. Set the splicing payload for uplink
	1173
	1174	Feature, splicing payload for uplink.
	1175
	1176	AT Command: AT+DATAUP
	1177
	1178	\|Command Example\|Function\|Response
	1179	\|AT+DATAUP =?\|Show current splicing payload for uplink mode\|(((
	1180	0
	1181
	1182
	1183	OK
	1184	)))
	1185	\|AT+DATAUP =0\|(((
	1186	Set splicing payload for uplink mode is 0.
	1187
	1188
	1189	)))\|(((
	1190	OK
	1191
	1192
	1193	)))
	1194	\|AT+DATAUP =1\|Set splicing payload for uplink mode is 1 , and the each splice uplink is sent sequentially.\|OK
	1195	\|AT+DATAUP =1,20000\|(((
	1196	Set splicing payload for uplink mode is 1, and the uplink interval of each splice to 20000 milliseconds.
	1197
	1198
	1199	)))\|OK
	1200
	1201	Downlink Command: 0xAD
	1202
	1203	Format: Command Code (0xAD) followed by 1 bytes or 5 bytes.
	1204
	1205	* Example 1: Downlink Payload: AD 00 ~/~/ AT+DATAUP=0
	1206	* Example 2: Downlink Payload: AD 01 ~/~/ AT+DATAUP =1
	1207	* Example 3: Downlink Payload: AD 01 00 00 14~/~/ AT+DATAUP =1,20000
	1208
	1209	This means that the interval is set to 0x000014=20S
	1210
	1211
	1212	1.
	1213	11. Set the payload version
	1214
	1215	Feature, Set the payload version.
	1216
	1217	AT Command: AT+PAYVER
	1218
	1219	\|Command Example\|Function\|Response
	1220	\|AT+PAYVER=?\|Show current payload version\|(((
	1221	1
	1222
	1223
	1224	OK
	1225	)))
	1226	\|AT+PAYVER=5\|Set payload version is 5.\|OK
	1227
	1228	Downlink Command: 0xAE
	1229
	1230	Format: Command Code (0xAE) followed by 1 bytes.
	1231
	1232	* Example 1: Downlink Payload: AE 01 ~/~/ AT+PAYVER=1
	1233	* Example 2: Downlink Payload: AE 05 ~/~/ AT+PAYVER=5
	1234
	1235	1. Battery & how to replace
	1236	11. Battery Type
	1237
	1238	SDI-12-LB is equipped with a [[8500mAH ER26500 Li-SOCI2 battery>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]. The battery is un-rechargeable battery with low discharge rate targeting for 8~~10 years use. This type of battery is commonly used in IoT target for long-term running, such as water meter.
	1239
	1240
	1241	The discharge curve is not linear so can’t simply use percentage to show the battery level. Below is the battery performance.
	1242
	1243	[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image036.png]]
	1244
	1245
	1246	Minimum Working Voltage for the SDI-12-LB:
	1247
	1248	SDI-12-LB: 2.45v ~~ 3.6v
	1249
	1250
	1251	1.
	1252	11. Replace Battery
	1253
	1254	Any battery with range 2.45 ~~ 3.6v can be a replacement. We recommend to use Li-SOCl2 Battery.
	1255
	1256	And make sure the positive and negative pins match.
	1257
	1258
	1259
	1260	1.
	1261	11. Power Consumption Analyze
	1262
	1263	Dragino Battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
	1264
	1265
	1266	Instruction to use as below:
	1267
	1268
	1269	Step 1: Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from:
	1270
	1271	[[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/]]
	1272
	1273
	1274	Step 2: Open it and choose
	1275
	1276	* Product Model
	1277	* Uplink Interval
	1278	* Working Mode
	1279
	1280	And the Life expectation in difference case will be shown on the right.
	1281
	1282	[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image037.png]]
	1283
	1284
	1285	The battery related documents as below:
	1286
	1287	* [[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/&file=LSN50-Battery-Dimension.pdf]],
	1288	* [[Lithium-Thionyl Chloride Battery>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/ER18505_datasheet-EN.pdf]] datasheet, [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/ER18505_datasheet_PM-ER18505-S-02-LF_EN.pdf]]
	1289	* [[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC_1520_datasheet.jpg]], [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC1520%20Technical%20Specification20171123.pdf]]
	1290
	1291	\|(((
	1292	JST-XH-2P connector
	1293	)))
	1294
	1295	[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image038.png]]
	1296
	1297
	1298
9.2	1299	1.
2.2	1300	11.
	1301	111. Battery Note
	1302
	1303	The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
	1304
	1305
	1306	1.
	1307	11.
	1308	111. Replace the battery
	1309
	1310	You can change the battery in the SDI-12-LB.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
	1311
	1312
	1313	The default battery pack of SDI-12-LB includes a ER26500 plus super capacitor. If user can’t find this pack locally, they can find ER26500 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
	1314
	1315
	1316
	1317
	1318
	1319
	1320	1. Remote Configure device
	1321	11. Connect via BLE
	1322
	1323	Please see this instruction for how to configure via BLE:
	1324
	1325	[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]]
	1326
	1327
	1328	1.
	1329	11. AT Command Set
	1330
	1331	1. OTA firmware update
	1332
	1333	Please see this link for how to do OTA firmware update.
	1334
	1335	[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]
	1336
	1337
	1338
	1339
	1340
	1341
	1342
	1343
	1344
	1345
	1346
	1347	1. Order Info
	1348
	1349	Package Includes:
	1350
	1351	* SDI-12-LB SDI-12 to LoRaWAN Converter
	1352
	1353	Dimension and weight:
	1354
	1355	* Device Size: cm
	1356	* Device Weight: g
	1357	* Package Size / pcs : cm
	1358	* Weight / pcs : g
	1359
	1360
	1361
	1362	1. Support
	1363
	1364	* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
	1365	* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to
	1366
	1367	[[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]
	1368
	1369

Wiki source code of SDI-12-LB -- SDI-12 to LoRaWAN Converter User Manual

Applications

Navigation