Skip to Content
Version 178.1 by Saxer Lin on 2025/06/30 15:11
Show last authors
1
2
3 [[image:image-20240103165259-3.png||data-xwiki-image-style-alignment="center" height="433" width="591"]]
4
5
6
7
8
9
10
11 **Table of Contents:**
12
13 {{toc/}}
14
15
16
17
18
19
20
21
22
23
24
25
26
27 = 1. Introduction =
28
29 == 1.1 ​What is SDI-12 to LoRaWAN Converter ==
30
31
32 (((
33 The Dragino (% style="color:blue" %)**SDI-12-LB/LS**(%%) is a (% style="color:blue" %)**SDI-12 to LoRaWAN Converter **(%%)designed for Smart Agriculture solution.
34 )))
35
36 (((
37 SDI-12 (Serial Digital Interface at 1200 baud) is an asynchronous [[serial communications>>url:https://en.wikipedia.org/wiki/Serial_communication]] protocol for intelligent sensors that monitor environment data. SDI-12 protocol is widely used in Agriculture sensor and Weather Station sensors.
38 )))
39
40 (((
41 SDI-12-LB/LS has SDI-12 interface and support 12v output to power external SDI-12 sensor. It can get the environment data from SDI-12 sensor and sends out the data via LoRaWAN wireless protocol.
42 )))
43
44 (((
45 The LoRa wireless technology used in SDI-12-LB/LS allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
46 )))
47
48 (((
49 SDI-12-LB/LS is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%) or (% style="color:blue" %)**solar powered + Li-ion battery,**(%%) it is designed for long term use up to 5 years.
50 )))
51
52 (((
53 Each SDI-12-LB/LS is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
54 )))
55
56
57 == ​1.2 Features ==
58
59
60 * LoRaWAN 1.0.3 Class A
61 * Ultra-low power consumption
62 * Controllable 3.3v, 5v and 12v output to power external sensor
63 * SDI-12 Protocol to connect to SDI-12 Sensor
64 * Monitor Battery Level
65 * Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
66 * Support Bluetooth v5.1 and LoRaWAN remote configure.
67 * Support wireless OTA update firmware
68 * Uplink on periodically
69 * Downlink to change configure
70 * 8500mAh Li/SOCl2 Battery (SDI-12-LB)
71 * Solar panel + 3000mAh Li-ion battery (SDI-12-LS)
72
73 == 1.3 Specification ==
74
75
76 (% style="color:#037691" %)**Micro Controller:**
77
78 * MCU: 48Mhz ARM
79 * Flash: 256KB
80 * RAM: 64KB
81
82 (% style="color:#037691" %)**Common DC Characteristics:**
83
84 * Supply Voltage: Built-in Battery, 2.5v ~~ 3.6v
85 * Support current: 5V 300mA, 12V 100mA
86 * Operating Temperature: -40 ~~ 85°C
87
88 (% style="color:#037691" %)**LoRa Spec:**
89
90 * Frequency Range,  Band 1 (HF): 862 ~~ 1020 Mhz
91 * Max +22 dBm constant RF output vs.
92 * RX sensitivity: down to -139 dBm.
93 * Excellent blocking immunity
94
95 (% style="color:#037691" %)**Current Input Measuring :**
96
97 * Range: 0 ~~ 20mA
98 * Accuracy: 0.02mA
99 * Resolution: 0.001mA
100
101 (% style="color:#037691" %)**Voltage Input Measuring:**
102
103 * Range: 0 ~~ 30v
104 * Accuracy: 0.02v
105 * Resolution: 0.001v
106
107 (% style="color:#037691" %)**Battery:**
108
109 * Li/SOCI2 un-chargeable battery
110 * Capacity: 8500mAh
111 * Self-Discharge: <1% / Year @ 25°C
112 * Max continuously current: 130mA
113 * Max boost current: 2A, 1 second
114
115 (% style="color:#037691" %)**Power Consumption**
116
117 * Sleep Mode: 5uA @ 3.3v
118 * LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm
119
120 == 1.4 Connect to SDI-12 Sensor ==
121
122
123 [[image:1675212538524-889.png||_mstalt="298272"]]
124
125
126 == 1.5 Sleep mode and working mode ==
127
128
129 (% style="color:blue" %)**Deep Sleep Mode: **(%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.
130
131 (% style="color:blue" %)**Working Mode: **(%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.
132
133
134 == 1.6 Button & LEDs ==
135
136
137 [[image:image-20250416151419-4.jpeg]]
138
139 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
140 |=(% style="width: 167px;background-color:#4F81BD;color:white" %)**Behavior on ACT**|=(% style="width: 117px;background-color:#4F81BD;color:white" %)**Function**|=(% style="width: 226px;background-color:#4F81BD;color:white" %)**Action**
141 |[[image:1749523850351-927.png]] 1~~3s|(% style="background-color:#f2f2f2; width:117px" %)Send an uplink|(% style="background-color:#f2f2f2; width:225px" %)(((
142 If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, (% style="color:blue" %)**blue led** (%%)will blink once.
143 Meanwhile, BLE module will be active and user can connect via BLE to configure device.
144 )))
145 |[[image:1749523852387-583.png]] >3s|(% style="background-color:#f2f2f2; width:117px" %)Active Device|(% style="background-color:#f2f2f2; width:225px" %)(((
146 (% style="background-color:#f2f2f2; color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:#037691" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network.
147 (% style="background-color:#f2f2f2; color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.
148 Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device join or not join LoRaWAN network.
149 )))
150 |[[image:1749523825515-716.png]] x5|(% style="background-color:#f2f2f2; width:117px" %)Deactivate Device|(% style="background-color:#f2f2f2; width:225px" %)(% style="color:red" %)**Red led**(%%) will solid on for 5 seconds. Means SDI-12-LB/LS is in Deep Sleep Mode.
151
152 == 1.7 Pin Mapping ==
153
154
155 [[image:1675213198663-754.png||_mstalt="297167"]]
156
157
158 == 1.8 BLE connection ==
159
160
161 SDI-12-LB/LS support BLE remote configure.
162
163 BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:
164
165 * Press button to send an uplink
166 * Press button to active device.
167 * Device Power on or reset.
168
169 If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.
170
171
172 == 1.9 Mechanical ==
173
174 === 1.9.1 for LB version ===
175
176
177 [[image:image-20250416151406-3.jpeg]]
178
179
180 === 1.9.2 for LS version ===
181
182
183 [[image:image-20250329133856-1.jpeg]]
184
185
186 = 2. Configure SDI-12 to connect to LoRaWAN network =
187
188 == 2.1 How it works ==
189
190
191 The SDI-12-LB/LS is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and activate the SDI-12-LB/LS. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
192
193
194 == 2.2 Quick guide to connect to LoRaWAN server (OTAA) ==
195
196
197 Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.
198
199 [[image:image-20250416151346-2.png]]
200
201
202 The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
203
204
205 (% style="color:blue" %)**Step 1**(%%): Create a device in TTN with the OTAA keys from SDI-12-LB/LS.
206
207 Each SDI-12-LB/LS is shipped with a sticker with the default device EUI as below:
208
209 [[image:image-20230426084456-1.png||height="241" width="519"]]
210
211
212 You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
213
214 **Create the application.**
215
216 [[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SAC01L_LoRaWAN_Temperature%26Humidity_Sensor_User_Manual/WebHome/image-20250423093843-1.png?width=756&height=264&rev=1.1||alt="image-20250423093843-1.png"]]
217
218 [[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LTC2-LB--LoRaWAN_Temperature_Transmitter_User_Manual/WebHome/image-20240907111305-2.png?width=1000&height=572&rev=1.1||alt="image-20240907111305-2.png"]]
219
220
221 **Add devices to the created Application.**
222
223 [[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LTC2-LB--LoRaWAN_Temperature_Transmitter_User_Manual/WebHome/image-20240907111659-3.png?width=977&height=185&rev=1.1||alt="image-20240907111659-3.png"]]
224
225 [[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LTC2-LB--LoRaWAN_Temperature_Transmitter_User_Manual/WebHome/image-20240907111820-5.png?width=975&height=377&rev=1.1||alt="image-20240907111820-5.png"]]
226
227
228 **Enter end device specifics manually.**
229
230 [[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LTC2-LB--LoRaWAN_Temperature_Transmitter_User_Manual/WebHome/image-20240907112136-6.png?width=697&height=687&rev=1.1||alt="image-20240907112136-6.png"]]
231
232
233 **Add DevEUI and AppKey.**
234
235 **Customize a platform ID for the device.**
236
237 [[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LTC2-LB--LoRaWAN_Temperature_Transmitter_User_Manual/WebHome/image-20240907112427-7.png?rev=1.1||alt="image-20240907112427-7.png"]]
238
239
240 (% style="color:blue" %)**Step 2: **(%%)Add decoder
241
242 While using TTN network, you can add the payload format to decode the payload.
243
244 There is no fix payload decoder in LoRaWAN server because the SDI-12 sensors returns are different. User need to write the decoder themselves for their case.
245
246 SDI-12-LB/LS TTN Payload Decoder: [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>url:https://github.com/dragino/dragino-end-node-decoder]]
247
248 Below is TTN screen shot:
249
250 [[image:image-20241118165746-3.png||height="470" width="869"]]
251
252 [[image:image-20241118165832-4.png||height="336" width="724"]]
253
254
255 (% style="color:blue" %)**Step 3**(%%): Activate on SDI-12-LB/LS
256
257 Press the button for 5 seconds to activate the SDI-12-LB/LS.
258
259 (% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:blue" %)**OTA mode** (%%)for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.
260
261 [[image:1675213704414-644.png||_mstalt="293748"]]
262
263
264 == ​2.3 SDI-12 Related Commands ==
265
266
267 User need to configure SDI-12-LB/LS to communicate with SDI-12 sensors otherwise the uplink payload will only include a few bytes.
268
269 If you use UART to connect a computer, refer to the following connection methods:
270
271 [[image:image-20240823165402-1.jpeg||height="488" width="678"]]
272
273 Screenshot example:
274
275 [[image:image-20240823165526-2.png||height="489" width="690"]]
276
277
278
279 === 2.3.1 Basic SDI-12 debug command ===
280
281
282 User can run some basic SDI-12 command to debug the connection to the SDI-12 sensor. These commands can be sent via AT Command or LoRaWAN downlink command.
283
284 If SDI-12 sensor return value after get these commands, //SDI-12-LB/LS// will uplink the return on FPORT=100, otherwise, if there is no response from SDI-12 sensor. //SDI-12-LB/LS// will uplink NULL (0x 4E 55 4C 4C) to server.
285
286 The following is the display information on the serial port and the server.
287
288
289 [[image:image-20230201091027-6.png||_mstalt="429065"]]
290
291
292 [[image:image-20230201091027-7.png||_mstalt="429429" height="261" width="1179"]]
293
294
295
296 ==== (% style="color:blue" %)**al!  ~-~- Get SDI-12 sensor Identification**(%%) ====
297
298
299 * AT Command: AT+ADDRI=aa
300 * LoRaWAN Downlink(prefix 0xAA00): AA 00 aa
301
302 (% style="color:#037691" %)**Parameter:  **(%%)aa: ASCII value of SDI-12 sensor address in downlink or HEX value in AT Command)
303
304 (% style="color:blue" %)**Example :   **(%%)AT+ADDRI=0 ( Equal to downlink: 0x AA 00 30)
305
306
307 The following is the display information on the serial port and the server.
308
309
310 [[image:image-20230201091257-8.png||_mstalt="431392"]]
311
312
313 [[image:image-20230201091257-9.png||_mstalt="431756" height="225" width="1242"]]
314
315
316 ==== (% style="color:blue" %)**aM!,aMC!, aM1!- aM9!, aMC1!- aMC9!**(%%) ====
317
318
319 (% style="color:red" %)**aM! **(%%): Start Non-Concurrent Measurement
320
321 (% style="color:red" %)**aMC! **(%%): Start Non-Concurrent Measurement – Request CRC
322
323 (% style="color:red" %)**aM1!- aM9! **(%%): Additional Measurements
324
325 (% style="color:red" %)**aMC1!- aMC9!**(%%) : Additional Measurements – Request CRC
326
327
328 * AT Command : AT+ADDRM=0,1,0,1
329
330 * LoRaWAN Downlink(prefix 0xAA01): 0xAA 01 30 01 00 01
331
332 Downlink：AA 01 aa bb cc dd
333
334 (% style="color:#037691" %)**aa**(%%): SDI-12 sensor address.
335
336 (% style="color:#037691" %)**bb**(%%): 0: no CRC, 1: request CRC
337
338 (% style="color:#037691" %)**cc**(%%): 1-9: Additional Measurement, 0: no additional measurement
339
340 (% style="color:#037691" %)**dd**(%%): delay (in second) to send (% style="color:#037691" %)__**aD0!**__(%%) to get return.
341
342
343 The following is the display information on the serial port and the server.
344
345
346 [[image:image-20230201091630-10.png||_mstalt="449995"]]
347
348
349 [[image:image-20230201091630-11.png||_mstalt="450372" height="247" width="1165"]]
350
351
352
353 ==== (% style="color:blue" %)**aC!, aCC!,  aC1!- aC9!,  aCC1!- aCC9! **(%%) ====
354
355
356 (% style="color:red" %)**aC!**(%%) : Start Concurrent Measurement
357
358 (% style="color:red" %)**aCC!** (%%): Start Concurrent Measurement – Request CRC
359
360 (% style="color:red" %)**aC1!- aC9!**(%%) : Start Additional Concurrent Measurements
361
362 (% style="color:red" %)**aCC1!- aCC9!**(%%) : Start Additional Concurrent Measurements – Request CRC
363
364
365 * AT Command : AT+ADDRC=0,1,0,1 
366
367 * LoRaWAN Downlink(0xAA02): 0xAA 02 30 01 00 01
368
369 Downlink: AA 02 aa bb cc dd
370
371 (% style="color:#037691" %)**aa**(%%): SDI-12 sensor address.
372
373 (% style="color:#037691" %)**bb**(%%): 0: no CRC, 1: request CRC
374
375 (% style="color:#037691" %)**cc**(%%): 1-9: Additional Measurement, 0: no additional measurement
376
377 (% style="color:#037691" %)**dd**(%%): delay (in second) to send (% style="color:#037691" %)__**aD0!**__(%%)__ __to get return.
378
379
380 The following is the display information on the serial port and the server.
381
382
383 [[image:image-20230201091954-12.png||_mstalt="453687"]]
384
385
386 [[image:image-20230201091954-13.png||_mstalt="454064" height="203" width="1117"]]
387
388
389
390 ==== (% style="color:blue" %)**aR0!- aR9!,  aRC0!- aRC9!**(%%) ====
391
392
393 Start Continuous Measurement
394
395 Start Continuous Measurement – Request CRC
396
397
398 * AT Command : AT+ADDRR=0,1,0,1 
399 * LoRaWAN Downlink (0xAA 03): 0xAA 03 30 01 00 01
400
401 Downlink: AA 03 aa bb cc dd
402
403 (% style="color:#037691" %)**aa**(%%): SDI-12 sensor address.
404
405 (% style="color:#037691" %)**bb**(%%): 0: no CRC, 1: request CRC
406
407 (% style="color:#037691" %)**cc**(%%): 1-9: Additional Measurement, 0: no additional measurement
408
409 (% style="color:#037691" %)**dd**(%%): delay (in second) to send (% style="color:#037691" %)__**aD0!**__(%%) to get return.
410
411
412 The following is the display information on the serial port and the server.
413
414
415 [[image:image-20230201092208-14.png||_mstalt="452283"]]
416
417
418 [[image:image-20230201092208-15.png||_mstalt="452660" height="214" width="1140"]]
419
420
421 === 2.3.2 Advance SDI-12 Debug command ===
422
423
424 This command can be used to debug all SDI-12 command.
425
426
427 LoRaWAN Downlink: A8 aa xx xx xx xx bb cc dd
428
429 (% style="color:#037691" %)**aa **(%%): total SDI-12 command length
430
431 (% style="color:#037691" %)**xx **(%%): SDI-12 command
432
433 (% style="color:#037691" %)**bb **(%%): Delay to wait for return
434
435 (% style="color:#037691" %)**cc **(%%): 0: don't uplink return to LoRaWAN, 1: Uplink return to LoRaWAN on FPORT=100
436
437 (% style="color:#037691" %)**dd: **(%%) 0: Do not use aD0! command access, 1: use aD0! command access.
438
439
440 (% style="color:blue" %)**Example1: **(%%) AT+CFGDEV =0RC0!,1
441
442 (% style="color:#037691" %)**0RC0! **(%%): SDI-12 Command,
443
444 (% style="color:#037691" %)**1 **(%%): Delay 1 second.  ( 0: 810 mini-second)
445
446 Equal Downlink: 0xA8 05 30 52 43 30 21 01 01
447
448
449 The following is the display information on the serial port and the server.
450
451
452 [[image:image-20230201092355-16.png||_mstalt="453960"]]
453
454
455 [[image:image-20230201092355-17.png||_mstalt="454337" height="426" width="1135"]]
456
457
458 (% style="color:blue" %)**Example2: **(%%) AT+CFGDEV =0M!,1,1
459
460 (% style="color:#037691" %)**0M! **(%%): SDI-12 Command,
461
462 (% style="color:#037691" %)**1 **(%%): Delay 1 second.  ( 0: 810 mini-second)
463
464 (% style="color:#037691" %)**1 **(%%): Use aD0! command access.
465
466 Equal Downlink: 0xA8 03 30  4D 21 01 01 01
467
468
469 The following is the display information on the serial port and the server.
470
471
472 [[image:image-20230628091055-1.png||height="368" width="462"]]
473
474 [[image:image-20230628091130-2.png||height="258" width="879"]]
475
476
477 === 2.3.3 Convert ASCII to String ===
478
479
480 This command is used to convert between ASCII and String format.
481
482 AT+CONVFORM ( Max length: 80 bytes)
483
484
485 (% style="color:blue" %)**Example:**
486
487 1) AT+CONVFORM=0, string Convert String from String to ASCII
488
489 [[image:1675214845056-885.png||_mstalt="297622"]]
490
491
492 2) AT+CONVFORM=1, ASCII Convert ASCII to String.
493
494 [[image:1675214856590-846.png||_mstalt="297739"]]
495
496
497 === 2.3.4 Define periodically SDI-12 commands and uplink. ===
498
499
500 AT+COMMANDx & AT+DATACUTx**&AT+DATACONVx**
501
502 User can define max 15 SDI-12 Commands (AT+COMMAND1 ~~ AT+COMMANDF). On each uplink period (TDC time, default 20 minutes), SDI-12-LB/LS will send these SDI-12 commands and wait for return from SDI-12 sensors. SDI-12-LB/LS will then combine these returns and uplink via LoRaWAN.
503
504
505 * (% style="color:blue" %)**AT Command:**
506
507 (% style="color:#037691" %)**AT+COMMANDx=var1,var2,var3,var4.**
508
509 (% style="color:red" %)**var1**(%%): SDI-12 command , for example: 0RC0!
510
511 (% style="color:red" %)**var2**(%%): Wait timeout for return. (unit: second)
512
513 (% style="color:red" %)**var3**(%%): Whether to send //addrD0!// to get return after var2 timeout. 0: Don't Send //addrD0! //; 1: Send //addrD0!//. (% style="color:red" %)**2: When set to 2, AT+ALDATAMOD=1 does not intercept data returned by the current COMMAND command.(since v1.3.0)**
514
515 (% style="color:red" %)**(Function set to 2: When the device is connected to more than two sensors with different sampling addresses, concurrent measurement can be used to reduce data acquisition time and save battery power; for example, when a device is connected to two sensors with different addresses, and both sensors are to use concurrent measurements, then both sensors can be measured at the same time without the second one having to wait until after the first one.)**
516
517 (% style="color:red" %)**var4**(%%): validation check for return. If return invalid, SDI-12-LB/LS will resend this command. Max 3 retries.
518
519 (% style="color:red" %)**0 **(%%) No validation check;
520
521 (% style="color:red" %)**1** (%%) Check if return chars are printable char(0x20 ~~ 0x7E);
522
523 (% style="color:red" %)**2**(%%)  Check if there is return from SDI-12 sensor
524
525 (% style="color:red" %)**3** (%%) Check if return pass CRC check ( SDI-12 command var1 must include CRC request);
526
527
528 Each AT+COMMANDx is followed by a (% style="color:blue" %)**AT+DATACUT**(%%) command. AT+DATACUT command is used to take the useful string from the SDI-12 sensor so the final payload will have the minimum length to uplink.
529
530
531 (% style="color:blue" %)**AT+DATACUTx**(%%) : This command defines how to handle the return from AT+COMMANDx, max return length is 100 bytes.
532
533 (% border="1" style="width:436px" %)
534 |(% style="background-color:#f2f2f2; width:433px" %)(((
535 (% style="color:#0070c0" %)**AT+DATACUTx=a,b,c**
536
537 **a**:  length for the return of AT+COMMAND
538
539 **b**: 1: grab valid value by byte, max 6 bytes. 2: grab valid value by bytes section, max 3 sections.
540
541 **c**:  define the position for valid value. 
542 )))
543
544 For example, if return from AT+COMMAND1 is “013METER   TER12 112T12-00024895<CR><LF>” , Below AT+DATACUT1 will get different result to combine payload:
545
546
547 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
548 |=(% style="width: 164px;background-color:#4F81BD;color:white" %)**AT+DATACUT1 value**|=(% style="width: 346px;background-color:#4F81BD;color:white" %)**Final Result to combine Payload**
549 |(% style="background-color:#f2f2f2; width:164px" %)34,1,1+2+3|(% style="background-color:#f2f2f2; width:344px" %)0D 00 01 30 31 33
550 |(% style="background-color:#f2f2f2; width:164px" %)34,2,1~~8+12~~16|(% style="background-color:#f2f2f2; width:344px" %)0D 00 01 30 31 33 4D 45 54 45 52 54 45 52 31 32
551 |(% style="background-color:#f2f2f2; width:164px" %)34,2,1~~34|(% style="background-color:#f2f2f2; width:344px" %)0D 00 01 30 31 33 4D 45 54 45 52 20 20 20 54 45 52 31 32 20 31 31 32 54 31 32 2D 30 30 30 32 34 38 39 35 0D 0A
552
553 * (% style="color:blue" %)** Downlink Payload:**
554
555 (% style="color:blue" %)**0xAF**(%%)  downlink command can be used to set AT+COMMANDx or AT+DATACUTx.
556
557
558 (% style="color:red" %)**Note : if user use AT+COMMANDx to add a new command, he also need to send AT+DATACUTx downlink.**
559
560
561 Format: ** (% style="color:#037691" %)AF MM NN LL XX XX XX XX YY(%%)**
562
563 Where:
564
565 * (% style="color:#037691" %)**MM **(%%): the AT+COMMAND or AT+DATACUT to be set. Value from 01 ~~ 0F,
566 * (% style="color:#037691" %)**NN **(%%):  1: set the AT+COMMAND value ; 2: set the AT+DATACUT value.
567 * (% style="color:#037691" %)**LL **(%%):  The length of AT+COMMAND or AT+DATACUT command
568 * (% style="color:#037691" %)**XX XX XX XX **(%%): AT+COMMAND or AT+DATACUT command
569 * (% style="color:#037691" %)**YY **(%%):  If YY=0, SDI-12-LB/LS will execute the downlink command without uplink; if YY=1, SDI-12-LB/LS will execute an uplink after got this command. 
570
571 (% style="color:blue" %)**Example:**
572
573 [[image:image-20230201094129-18.png||_mstalt="455065"]]
574
575
576
577 (% style="color:blue" %)**Clear SDI12 Command**
578
579 The AT+COMMANDx and AT+DATACUTx settings are stored in special location, user can use below command to clear them.
580
581
582 * (% style="color:#037691" %)**AT Command:**
583
584 (% style="color:#4f81bd" %)**AT+CMDEAR=mm,nn** (%%) mm: start position of erase ,nn: stop position of erase
585
586
587 Etc. AT+CMDEAR=1,10 means erase AT+COMMAND1/AT+DATACUT1 to AT+COMMAND10/AT+DATACUT10
588
589
590 * (% style="color:#037691" %)**Downlink Payload:**
591
592 (% style="color:#4f81bd" %)**0x09 aa bb**(%%)  same as AT+CMDEAR=aa,bb
593
594
595
596 (% style="color:blue" %)**command combination**
597
598 Below shows a screen shot how the results combines together to a uplink payload.
599
600 [[image:1675215745275-920.png||_mstalt="295334"]]
601
602
603 If user don't want to use DATACUT for some command, he simply want to uplink all returns. AT+ALLDATAMOD can be set to 1.
604
605 (% style="color:blue" %)**AT+ALLDATAMOD**(%%) will simply get all return and don't do CRC check as result for SDI-12 command. AT+DATACUTx command has higher priority, if AT+DATACUTx has been set, AT+ALLDATAMOD will be ignore for this SDI-12 command.
606
607
608 (% style="color:#4f81bd" %)**For example: **(%%) as below photo, AT+ALLDATAMOD=1, but AT+DATACUT1 has been set, AT+DATACUT1 will be still effect the result.
609
610
611 [[image:1675215782925-448.png||_mstalt="297466"]]
612
613
614 If AT+ALLDATAMOD=1, (% style="color:#4f81bd" %)**FX,X**(%%) will be added in the payload, FX specify which command is used and X specify the length of return. for example in above screen, F1 05 means the return is from AT+COMMAND1 and the return is 5 bytes.
615
616
617 (% style="color:blue" %)**Compose Uplink**
618
619 (% style="color:#4f81bd" %)**AT+DATAUP=0**
620
621 Compose the uplink payload with value returns in sequence and send with **__A SIGNLE UPLINK__**.
622
623 Final Payload is **__Battery Info+PAYVER + VALID Value from RETURN1 + Valid Value from RETURN2 + … + RETURNx__**
624
625 Where PAYVER is defined by AT+PAYVER, below is an example screen shot.
626
627
628 [[image:1675215828102-844.png||_mstalt="294645"]]
629
630
631 (% style="color:#4f81bd" %)**AT+DATAUP=1**
632
633 Compose the uplink payload with value returns in sequence and send with **__Multiply UPLINKs__**.
634
635 Final Payload is __**Battery Info+PAYVER + PAYLOAD COUNT + PAYLOAD# + DATA**__
636
637 1. Battery Info (2 bytes): Battery voltage
638 1. PAYVER (1 byte): Defined by AT+PAYVER
639 1. PAYLOAD COUNT (1 byte): Total how many uplinks of this sampling.
640 1. PAYLOAD# (1 byte): Number of this uplink. (from 0,1,2,3…,to PAYLOAD COUNT)
641 1. DATA: Valid value: max 6 bytes(US915 version here, Notice*!) for each uplink so each uplink <= 11 bytes. For the last uplink, DATA will might less than 6 bytes
642
643 [[image:1675215848113-696.png||_mstalt="296998"]]
644
645
646 (% style="color:red" %)**Notice: the Max bytes is according to the max support bytes in different Frequency Bands for lowest SF. As below:**
647
648 * For AU915/AS923 bands, if UplinkDwell time=0, max 51 bytes for each uplink ( so 51 -5 = 46 max valid date)
649 * For AU915/AS923 bands, if UplinkDwell time=1, max 11 bytes for each uplink ( so 11 -5 = 6 max valid date).
650 * For US915 band, max 11 bytes for each uplink ( so 11 -5 = 6 max valid date).
651 * For all other bands: max 51 bytes for each uplink  ( so 51 -5 = 46 max valid date).
652
653 (% style="color:red" %)**When AT+DATAUP=1, the maximum number of segments is 15, and the maximum total number of bytes is 1500;**
654
655 (% style="color:red" %)**When AT+DATAUP=1 and AT+ADR=0, the maximum number of bytes of each payload is determined by the DR value.**
656
657
658
659 (% style="color:blue" %)**Automatically converts polled data to hex format for uplinking(Since v1.3.0)**
660
661
662 This command can retrieve the returned data, convert the number after the positive or negative sign into a data, and then set the number of bytes to upload the data.
663
664
665 * (% style="color:blue" %)**AT Command:**
666
667 The maximum number can be set to 5 groups and the format of the command is as follows：
668
669 (% style="color:#037691" %)**Example 1:AT+DATACONVx=var1, var2**
670
671 (% style="color:#037691" %)**Example 2:AT+DATACONVx=var1, var2+ var3, var4**
672
673 (% style="color:#037691" %)**Example 3:AT+DATACONVx=var1, var2+ var3, var4+ var5, var6**
674
675 (% style="color:#037691" %)**Example 4:AT+DATACONVx=var1, var2+ var3, var4+ var5, var6+ var7, var8**
676
677 (% style="color:#037691" %)**Example 5:AT+DATACONVx=var1, var2+ var3, var4+ var5, var6+ var7, var8+ var9, var10**
678
679 (% style="color:red" %)**Notice: Among them, var1, var3, var5, var7, and var9 are the data to be selected for conversion, and var2, var4, var6, var8, and var10 are the number of bytes to be uploaded. The values of var2, var4, var6, var8, and var10 range from 1 to 4.**
680
681 * (% style="color:blue" %)**Downlink Command:**
682
683 Format: Command code (0xAC) followed by up to 20 bytes.
684
685
686 Example 1 1:AT+DATACONVx=var1, var2   
687
688 Downlink Command：AC x var1  var2
689
690 Example 1 2:AT+DATACONVx=var1, var2+ var3, var4 
691
692 Downlink Command：AC x var1  var2  var3 var4
693
694 Example 1 3:AT+DATACONVx=var1, var2+ var3, var4+ var5, var6
695
696 Downlink Command：AC x var1  var2  var3 var4 var5 var6
697
698 Example 1 4:AT+DATACONVx=var1, var2+ var3, var4+ var5, var6+ var7, var8
699
700 Downlink Command：AC x var1  var2  var3 var4 var5 var6 var7 var8
701
702 Example 1 5:AT+DATACONVx=var1, var2+ var3, var4+ var5, var6+ var7, var8+ var9, var10
703
704 Downlink Command：AC x var1  var2  var3 var4 var5 var6 var7 var8 var9 var10
705
706
707 Example:
708
709 * Example 1: Downlink Payload: AC 01 01 02 02 02  ~/~/  AT+DATACONV1=1,2+2,2 
710 * Example 2: Downlink Payload: AC 02 01 02 02 02 03 02  ~/~/  AT+DATACONV2=1,2+2,2+3,2
711
712 **For example:**
713
714 This is my configuration:
715
716 [[image:image-20250609134137-1.png]]
717
718
719 * AT+COMMAND1=0C!,0,2,0  Use concurrent measurement commands without intercepting the returned data.
720 * AT+COMMAND2=1C!,1,2,0  Use concurrent measurement commands without intercepting the returned data, with a second parameter to be set at the last concurrent command (the second parameter takes the maximum transition time between the two sensors)
721 * AT+COMMAND3=0D0!,0,0,0  Query the data measured by device 0
722 * AT+COMMAND4=1D0!,0,0,0  Query the data measured by device 1
723
724 This is the data obtained:
725
726 [[image:image-20250609134901-2.png]]
727
728
729 When using the AT+DATACONVx command,
730
731 The data of RETURN3 will be converted into 2 data, the first data is +192, and the second data is +258.
732
733 The data of RETURN4 will be converted into 3 data, the first data is +187716, and the second data is +252, and the third data is +1.
734
735 * AT+DATACONV3=1,2+2,2  The first data is uploaded as 2 bytes and the second data is uploaded as 2 bytes. The form converted to hexadecimal is as shown above,as below:
736 * (((
737 AT+DATACONV4=1,3+2,2+3,2  The first data uploads 3 bytes, the second data also uploads 2 bytes, and the third data also uploads 2 bytes. The hexadecimal form is shown above and as shown in the following figure:
738 )))
739
740
741
742 **For example,the uplink payload as below:**
743
744 0CFC 01 00C0 0102 02DD44 00FC 0001
745
746 (% style="color:#037691" %)**BAT**(%%): 0x0CFC = 3324mV = 3.324V
747
748 (% style="color:#037691" %)**Payload Version**(%%): 0x01, Means: v1.0 version
749
750 (% style="color:#037691" %)**Data 1: **(%%)0x00C0(H) = 192(D) / 100 = 19.2
751
752 (% style="color:#037691" %)**Data 2: **(%%)0x0102(H) = 258(D) / 10 = 25.8
753
754 (% style="color:#037691" %)**Data 3: **(%%)0x02DD44(H) = 187716(D) / 100 = 1877.16
755
756 (% style="color:#037691" %)**Data 4: **(%%)0x00FC(H) = 252(D) / 10 = 25.2
757
758 (% style="color:#037691" %)**Data 5: **(%%)0x0001(H) = 1(D) = 1
759
760
761 == 2.4 Uplink Payload ==
762
763 === 2.4.1 Device Payload, FPORT~=5 ===
764
765
766 Include device configure status. Once SDI-12-LB/LS Joined the network, it will uplink this message to the server.
767
768 Users can also use the downlink command(0x26 01) to ask SDI-12-LB/LS to resend this uplink.
769
770 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
771 |(% colspan="6" style="background-color:#4f81bd; color:white" %)**Device Status (FPORT=5)**
772 |(% style="background-color:#f2f2f2; width:103px" %)**Size (bytes)**|(% style="background-color:#f2f2f2; width:72px" %)**1**|(% style="background-color:#f2f2f2" %)**2**|(% style="background-color:#f2f2f2; width:91px" %)**1**|(% style="background-color:#f2f2f2; width:86px" %)**1**|(% style="background-color:#f2f2f2; width:44px" %)**2**
773 |(% style="background-color:#f2f2f2; width:103px" %)**Value**|(% style="background-color:#f2f2f2; width:72px" %)Sensor Model|(% style="background-color:#f2f2f2" %)Firmware Version|(% style="background-color:#f2f2f2; width:91px" %)Frequency Band|(% style="background-color:#f2f2f2; width:86px" %)Sub-band|(% style="background-color:#f2f2f2; width:44px" %)BAT
774
775 Example parse in TTNv3
776
777 [[image:1675215946738-635.png||_mstalt="297778"]]
778
779
780 (% style="color:#037691" %)**Sensor Model**(%%): For SDI-12-LB/LS, this value is 0x17
781
782 (% style="color:#037691" %)**Firmware Version**(%%): 0x0100, Means: v1.0.0 version
783
784 (% style="color:#037691" %)**Frequency Band**:
785
786 0x01: EU868
787
788 0x02: US915
789
790 0x03: IN865
791
792 0x04: AU915
793
794 0x05: KZ865
795
796 0x06: RU864
797
798 0x07: AS923
799
800 0x08: AS923-1
801
802 0x09: AS923-2
803
804 0x0a: AS923-3
805
806 0x0b: CN470
807
808 0x0c: EU433
809
810 0x0d: KR920
811
812 0x0e: MA869
813
814
815 (% style="color:#037691" %)**Sub-Band**:
816
817 AU915 and US915:value 0x00 ~~ 0x08
818
819 CN470: value 0x0B ~~ 0x0C
820
821 Other Bands: Always 0x00
822
823
824 (% style="color:#037691" %)**Battery Info**:
825
826 Check the battery voltage.
827
828 Ex1: 0x0B45 = 2885mV
829
830 Ex2: 0x0B49 = 2889mV
831
832
833 === 2.4.2 Uplink Payload, FPORT~=2 ===
834
835
836 There are different cases for uplink. See below
837
838 * SDI-12 Debug Command return: FPORT=100
839
840 * Periodically Uplink: FPORT=2
841
842 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:500px" %)
843 |=(% style="width: 90px;background-color:#4F81BD;color:white" %)(((
844 **Size(bytes)**
845 )))|=(% style="width: 80px;background-color:#4F81BD;color:white" %)**2**|=(% style="width: 90px;background-color:#4F81BD;color:white" %)**1**|=(% style="width: 240px;background-color:#4F81BD;color:white" %)**Length depends on the return from the commands**
846 |(% style="width:93px" %)Value|(% style="width:83px" %)(((
847 Battery(mV)
848 &
849 Interrupt_Flag
850 )))|(% style="width:91px" %)[[PAYLOAD_VER>>||anchor="H3.6Setthepayloadversion"]]|(% style="width:212px" %)(((
851 If the valid payload is too long and exceed the maximum support.
852 Payload length in server,server will show payload not provided in the LoRaWAN server.
853 )))
854
855 [[image:1675216282284-923.png||_mstalt="295633"]]
856
857
858 === 2.4.3 Battery Info ===
859
860
861 Check the battery voltage for SDI-12-LB/LS.
862
863 Ex1: 0x0B45 = 2885mV
864
865 Ex2: 0x0B49 = 2889mV
866
867
868 === 2.4.4 Interrupt Pin ===
869
870
871 This data field shows if this packet is generated by (% style="color:#037691" %)**Interrupt Pin**(%%) or not. [[Click here>>||anchor="H3.2SetInterruptMode"]] for the hardware and software set up. Note: The Internet Pin is a separate pin in the screw terminal. See [[pin mapping>>||anchor="H1.7PinMapping"]].
872
873 **Example:**
874
875 Ex1: 0x0B45:0x0B&0x80= 0x00    Normal uplink packet.
876
877 Ex2: 0x8B49:0x8B&0x80= 0x80    Interrupt Uplink Packet.
878
879
880 === 2.4.5 Payload version ===
881
882
883 The version number of the payload, mainly used for decoding. The default is 01.
884
885
886 === 2.4.6 ​Decode payload in The Things Network ===
887
888
889 While using TTN network, you can add the payload format to decode the payload.
890
891 [[image:1675216779406-595.png||_mstalt="298376"]]
892
893
894 There is no fix payload decoder in LoRaWAN server because the SDI-12 sensors returns are different. User need to write the decoder themselves for their case.
895
896 SDI-12-LB/LS TTN Payload Decoder: [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>url:https://github.com/dragino/dragino-end-node-decoder]]
897
898
899 == 2.5 Uplink Interval ==
900
901
902 The SDI-12-LB/LS by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link:
903
904 [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H4.1ChangeUplinkInterval>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H4.1ChangeUplinkInterval]]
905
906
907 == 2.6 Examples To Set SDI commands ==
908
909 === 2.6.1 Examples 1 ~-~- General Example ===
910
911
912 COM port and SDI-12 sensor communication converted to SDI-12-LB/LS and SDI-12 sensor communication.
913
914 [[image:image-20230222143809-1.png||_mstalt="429962" height="564" width="729"]]
915
916
917 (% style="color:blue" %)**1) The AT+COMMANDx command is applied to the red arrow part, and sends the SDI12 command to the SDI12 sensor:**
918
919 a. Send the first command and get the first reply：
920
921 (% style="color:#037691" %)**AT+COMMANDx=1I!,0,0,1**
922
923 b. Send the second command and get the second reply：
924
925 (% style="color:#037691" %)**AT+COMMANDx=2I!,0,0,1**
926
927 c. Send the third command and get the third reply：
928
929 (% style="color:#037691" %)**AT+COMMANDx=3I!,0,0,1**
930
931 d. Send the fourth command and get the fourth reply：
932
933 (% style="color:#037691" %)**AT+COMMANDx=4I!,0,0,1**
934
935 e. Send the fifth command plus the sixth command, get the sixth reply：
936
937 (% style="color:#037691" %)**AT+COMMANDx=1M!,2,1,1**
938
939 f. Send the seventh command plus the eighth command, get the eighth reply：
940
941 (% style="color:#037691" %)**AT+COMMANDx=2M!,2,1,1**
942
943 g. Send the ninth command plus the tenth command, get the tenth reply：
944
945 (% style="color:#037691" %)**AT+COMMANDx=3M!,1,1,1**
946
947 h. Send the eleventh command plus the twelfth command, get the twelfth reply：
948
949 (% style="color:#037691" %)**AT+COMMANDx=4M!,1,1,1**
950
951
952 (% style="color:blue" %)**2) The AT+DATACUTx command is applied to the green arrow part, receiving and cut out data from the SDI12 sensor:**
953
954 a. The first reply, all 34 characters: ”113TRUEBNERSMT100038220303182331<CR><LF>”
955
956 Cut out all characters: (% _mstmutation="1" style="color:#037691" %)**AT+ALLDATAMOD=1 or AT+DATACUTx=34,2,1~~34**(% style="color:#037691" %);
957
958 b. The sixth reply, all 31 characters: "1+19210+1.04+0.00+22.49+11.75<CR><LF>"
959
960 Cut out all characters: (% _mstmutation="1" style="color:#037691" %)**AT+ALLDATAMOD=1 or AT+DATACUTx=31,2,1~~31**(% style="color:#037691" %);
961
962 c. The eighth reply, all 31 characters: "2+18990+1.08+0.00+22.24+11.80<CR><LF>"
963
964 Cut out all characters: (% _mstmutation="1" style="color:#037691" %)**AT+ALLDATAMOD=1 or AT+DATACUTx=31,2,1~~31**(% style="color:#037691" %);
965
966 d. The tenth reply, all 15 characters: "3-2919.8+24.0<CR><LF>"
967
968 Cut out all characters: (% _mstmutation="1" style="color:#037691" %)**AT+ALLDATAMOD=1 or AT+DATACUTx=15,2,1~~15**(% style="color:#037691" %);
969
970 e. The twelfth reply, all 25 characters: "4+30.8+22.84+4.7+954.38<CR><LF>"
971
972 Partial cut, the cut sensor address and the first two parameters:(% style="color:#037691" %)**AT+DATACUTx=25,2,1~~12, cut out the character field "4+30.8+22.84"**.
973
974
975 === 2.6.2 Example 2 ~-~- Connect to Hygrovue10 ===
976
977 ==== 2.6.2.1 Reference Manual and Command ====
978
979
980 * [[Hygrovue10 Product Page>>https://www.campbellsci.com/hygrovue10]]
981
982 * Commands to be used in PC and output.
983
984 ~1. check device address
985
986 2. change device address
987
988 3. check device ID
989
990 4. start measure
991
992 5. Get Meausre result
993
994 [[image:image-20230603120209-2.png||height="281" width="267"]]
995
996
997 ==== 2.6.2.2 Hardware Connection to SDI-12-LB/LS ====
998
999
1000 [[image:image-20230603120515-3.png]]
1001
1002
1003 ==== 2.6.2.3 Commands set in SDI-12-LB/LS and uplink payload ====
1004
1005
1006 [[image:image-20230603120648-4.png]]
1007
1008 [[image:image-20230603120726-5.png]]
1009
1010
1011 **Data in TTN:**
1012
1013 [[image:image-20230603120859-6.png||height="118" width="1285"]]
1014
1015
1016 === 2.6.3 Example 3 ~-~- Connect to SIL-400 ===
1017
1018 ==== 2.6.3.1 Reference Manual and Command ====
1019
1020
1021 * [[SIL-400 Product Page>>https://www.apogeeinstruments.com/sil-411-commercial-grade-sdi-12-digital-output-standard-field-of-view-infrared-radiometer-sensor/]]
1022
1023 * Commands to be used in PC and output.
1024
1025 ~1. check device address
1026
1027 2. change device address
1028
1029 3. check device ID
1030
1031 4. start measure
1032
1033 5. Get Meausre result
1034
1035 [[image:image-20230603121606-7.png||height="242" width="307"]]
1036
1037
1038 ==== 2.6.3.2 Hardware Connection to SDI-12-LB/LS ====
1039
1040
1041 [[image:image-20230603121643-8.png||height="442" width="656"]]
1042
1043
1044 ==== 2.6.3.3 Commands set in SDI-12-LB/LS and uplink payload ====
1045
1046
1047 [[image:image-20230603121721-9.png]]
1048
1049 [[image:image-20230628090323-1.png||height="414" width="694"]]
1050
1051 Data in TTN:
1052
1053 [[image:image-20230603121826-11.png||height="155" width="1104"]]
1054
1055
1056 === 2.6.4 Example 4 ~-~- Connect to TEROS-12 ===
1057
1058 ==== 2.6.4.1 Reference Manual and Command ====
1059
1060
1061 * [[TEROS-12 Product Page>>https://www.metergroup.com/en/meter-environment/products/teros-12-soil-moisture-sensor]]
1062
1063 * Commands to be used in PC and output.
1064
1065 1.check device address
1066
1067 2.change device address
1068
1069 3.check device ID
1070
1071 4.start measure
1072
1073 5.Get Meausre result
1074
1075 [[image:image-20230603122248-16.png||height="196" width="198"]]
1076
1077
1078 ==== 2.6.4.2 Hardware Connection to SDI-12-LB/LS ====
1079
1080
1081 [[image:image-20230603122212-15.png||height="502" width="667"]]
1082
1083
1084 ==== 2.6.4.3 Commands set in SDI-12-LB/LS and uplink payload ====
1085
1086
1087 [[image:image-20230603122040-12.png]]
1088
1089 [[image:image-20230603122109-13.png||height="469" width="762"]]
1090
1091
1092 **Data in TTN:**
1093
1094 [[image:image-20230603122139-14.png||height="148" width="1128"]]
1095
1096
1097 === 2.6.5 Example 5 ~-~- Connect to SIL-400/TEROS-12 & Hygrovue10 ===
1098
1099 ==== 2.6.5.1 Important Notice! ====
1100
1101
1102 * The product page and reference command see above example 2,3,4
1103
1104 * All of these SDI-12 sensors use the same address (address 0) by default. So we need to change their address to different address, by using **aAb!** command. See above example.
1105
1106 * The sensor needs to be powered to a steady statue. So the 12VT time need to be set to the maximum stable time for the sensors. in this example, it is 13 seconds.
1107
1108 * If these SDI-12 sensors are powered by external power source. It will add 300uA in the total current in SDI-12-LB/LS.
1109
1110 ==== 2.6.5.2 Hardware Connection to SDI-12-LB/LS ====
1111
1112
1113 [[image:image-20230603122508-17.png||height="526" width="742"]]
1114
1115
1116 ==== 2.6.5.3 Commands set in SDI-12-LB/LS and uplink payload ====
1117
1118
1119 [[image:image-20230603122549-18.png]]
1120
1121 [[image:image-20230603122623-19.png||height="483" width="1121"]]
1122
1123
1124 **Data in TTN:**
1125
1126 [[image:image-20230603122719-20.png||height="151" width="1179"]]
1127
1128
1129 === 2.6.6 Example 6 ~-~- Connect to ENTELECHY-EP_SDI-12 ===
1130
1131 ==== 2.6.6.1 Reference Manual and Command ====
1132
1133
1134 * [[https:~~/~~/enviroprosoilprobes.com/wp-content/uploads/2019/11/ENTELECHY-EP_SDI-12-Commands.pdf>>url:https://enviroprosoilprobes.com/wp-content/uploads/2019/11/ENTELECHY-EP_SDI-12-Commands.pdf]]
1135
1136 * Commands to be used in PC and output.
1137
1138 1.check device address
1139
1140 2.change device address
1141
1142 3.check device ID
1143
1144 4.start measure
1145
1146 5.Get Meausre result
1147
1148
1149 [[image:image-20230627174559-3.png]]
1150
1151
1152 ==== 2.6.6.2 Hardware Connection to SDI-12-LB/LS ====
1153
1154
1155 [[image:image-20230627174446-2.png]]
1156
1157
1158 ==== 2.6.6.3 Commands set in SDI-12-LB/LS and uplink payload ====
1159
1160
1161 [[image:image-20230627175513-4.png||height="596" width="576"]]
1162
1163 [[image:image-20230627175736-5.png||height="429" width="693"]]
1164
1165
1166 **Data in TTN:**
1167
1168 [[image:image-20230627180303-6.png||height="292" width="1171"]]
1169
1170
1171 === 2.6.7 Example 7 ~-~- Connect to GroPoint Profile-8 (SDI-12 Version) ===
1172
1173 ==== 2.6.7.1  Reference Manual and Command ====
1174
1175
1176 * [[https:~~/~~/static1.squarespace.com/static/5db0b690c4990258f8f6d042/t/64189e1ab3ebc54e6947b0c0/1679334941034/2625-N-T+GroPoint+Profile+User+Manual-V1.1.3.pdf>>https://static1.squarespace.com/static/5db0b690c4990258f8f6d042/t/64189e1ab3ebc54e6947b0c0/1679334941034/2625-N-T+GroPoint+Profile+User+Manual-V1.1.3.pdf]]
1177
1178 * Commands to be used in PC and output.
1179
1180 1. check device address
1181 1. change device address
1182 1. check device ID
1183 1. start measure
1184 1. Get Meausre result
1185
1186 [[image:image-20240423143921-1.png]]
1187
1188
1189 ==== 2.6.7.2 Hardware Connection to SDI-12-LB/LS ====
1190
1191
1192 (% style="color:red" %)**Note: When the bytes returned by the sensor are not fixed, the full byte interception can be used: AT+ALLDATAMOD=1 (The DATACUTx parameter needs to be cleared when using this directive, or it will not work.)**
1193
1194 [[image:image-20240423145522-2.png||height="345" width="400"]]
1195
1196
1197 ==== 2.6.7.3 Commands set in SDI-12-LB/LS and uplink payload ====
1198
1199 [[image:image-20240423151202-3.png]]
1200
1201 (% class="wikigeneratedid" id="H" %)
1202 [[image:image-20240423162851-6.png||height="251" width="935"]]
1203
1204
1205 DATA in TTN:
1206
1207 [[image:image-20240423162322-4.png||height="269" width="933"]]
1208
1209
1210 === 2.6.8 Example 8 ~-~- Connect to Acclima TDR Soil Moisture Sensor ===
1211
1212 ==== 2.6.8.1  Reference Manual and Command ====
1213
1214
1215 * [[Acclima TDR Soil Moisture Sensor User Manual>>url:https://acclima.com/tdr-soil-moisture-sensor-user-manual/]]
1216
1217 * Commands to be used in PC and output.
1218
1219 1. check device address
1220 1. change device address
1221 1. check device ID
1222 1. start measure
1223 1. Get Meausre result
1224
1225 [[image:image-20240903152650-3.png]]
1226
1227 [[image:image-20240903152627-2.png]]
1228
1229
1230 ==== 2.6.8.2 Hardware Connection to SDI-12-LB/LS ====
1231
1232
1233 (% style="color:red" %)**Note: When the bytes returned by the sensor are not fixed, the full byte interception can be used: AT+ALLDATAMOD=1 (The DATACUTx parameter needs to be cleared when using this directive, or it will not work.)**
1234
1235 [[image:image-20240903153004-5.png||height="358" width="660"]]
1236
1237
1238 ==== 2.6.8.3 Commands set in SDI-12-LB/LS and uplink payload ====
1239
1240
1241 [[image:image-20240903153258-6.png]]
1242
1243 [[image:image-20240903153627-7.png]]
1244
1245 DATA in TTN:
1246
1247 [[image:image-20240903154020-10.png||height="467" width="961"]]
1248
1249
1250 == 2.7 Frequency Plans ==
1251
1252
1253 The SDI-12-LB/LS uses OTAA mode and below frequency plans by default. Each frequency band use different firmware, user update the firmware to the corresponding band for their country.
1254
1255 [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]
1256
1257
1258 == 2.8 Firmware Change Log ==
1259
1260
1261 **Firmware download link:**
1262
1263 [[https:~~/~~/www.dropbox.com/sh/qrbgbikb109lkiv/AACBR-v_ZhZAMengcY7Nsa1ja?dl=0>>https://www.dropbox.com/sh/qrbgbikb109lkiv/AACBR-v_ZhZAMengcY7Nsa1ja?dl=0]]
1264
1265
1266
1267 == 2.9 Datalog Feature(Since v1.3.0) ==
1268
1269
1270 (((
1271 Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, SDI-12-LB will store the reading for future retrieving purposes. There are two ways for IoT servers to get datalog from SDI-12-LB.
1272 )))
1273
1274
1275 === 2.9.1 Ways to get datalog via LoRaWAN ===
1276
1277
1278 There are two methods:
1279
1280 (% style="color:blue" %)**Method 1:** (%%)IoT Server sends a downlink LoRaWAN command to [[poll the value>>||anchor="H2.8.4Pollsensorvalue"]] for specified time range.
1281
1282
1283 (% style="color:blue" %)**Method 2: **(%%)Set PNACKMD=1, SDI-12-LB will wait for ACK for every uplink, when there is no LoRaWAN network, SDI-12-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
1284
1285
1286 (% style="color:red" %)**Note for method 2:**
1287
1288 * a) SDI-12-LB will do an ACK check for data records sending to make sure every data arrive server.
1289 * b) SDI-12-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but SDI-12-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if SDI-12-LB gets a ACK, SDI-12-LB will consider there is a network connection and resend all NONE-ACK Message.
1290
1291 === 2.9.2 Unix TimeStamp ===
1292
1293
1294 SDI-12-LB uses Unix TimeStamp format based on
1295
1296 [[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-11.png?width=627&height=97&rev=1.1||alt="image-20220523001219-11.png"]]
1297
1298
1299 User can get this time from link:  [[https:~~/~~/www.epochconverter.com/>>url:https://www.epochconverter.com/]] :
1300
1301 Below is the converter example
1302
1303 [[image:https://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-12.png?width=720&height=298&rev=1.1||alt="image-20220523001219-12.png"]]
1304
1305 So, we can use AT+TIMESTAMP=1742889625 or downlink 3067E26299 to set the current time 2025 – March ~-~- 25 Tuesday  08:00:25
1306
1307
1308 === 2.9.3 Set Device Time ===
1309
1310
1311 (((
1312 (% style="color:blue" %)**There are two ways to set device's time:**
1313 )))
1314
1315 (((
1316 **1.  Through LoRaWAN MAC Command (Default settings)**
1317 )))
1318
1319 (((
1320 User need to set SYNCMOD=1 to enable sync time via MAC command.
1321 )))
1322
1323 (((
1324 Once SDI-12-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to SDI-12-LB. If SDI-12-LB fails to get the time from the server, SDI-12-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
1325 )))
1326
1327 (((
1328 (% style="color:red" %)**Note: LoRaWAN Server need to support LoRaWAN v1.0.3(MAC v1.0.3) or higher to support this MAC command feature, Chirpstack,TTN V3 v3 and loriot support but TTN V3 v2 doesn't support. If server doesn't support this command, it will through away uplink packet with this command, so user will lose the packet with time request for TTN V3 v2 if SYNCMOD=1.**
1329 )))
1330
1331
1332 (((
1333 **2. Manually Set Time**
1334 )))
1335
1336 (((
1337 User needs to set SYNCMOD=0 to manual time, otherwise, the user set time will be overwritten by the time set by the server.
1338 )))
1339
1340
1341 === 2.9.4 Poll sensor value ===
1342
1343
1344 User can poll sensor value based on timestamps from the server. Below is the downlink command.
1345
1346 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:438.778px" %)
1347 |(% style="background-color:#4f81bd; color:white; width:59px" %)**1byte**|(% style="background-color:#4f81bd; color:white; width:123px" %)**4bytes**|(% style="background-color:#4f81bd; color:white; width:114px" %)**4bytes**|(% style="background-color:#4f81bd; color:white; width:142.778px" %)**1byte**
1348 |(% style="width:58px" %)31|(% style="width:123px" %)Timestamp start|(% style="width:114px" %)Timestamp end|(% style="width:137px" %)(((
1349 Uplink Interval(range 5~~255s)
1350 )))
1351
1352 Timestamp start and Timestamp end use Unix TimeStamp format as mentioned above. Devices will reply with all data log during this time period, use the uplink interval.
1353
1354 For example, downlink command (% _mstmutation="1" %)**31 68253B6E 68253E23 05**(%%)
1355
1356 Is to check 2025/05/15 00:55:10 to 2025/05/15 01:06:43's data
1357
1358 Uplink Internal =5s, means SDI-12-LB will send one packet every 5s.
1359
1360
1361 === 2.9.5 Datalog Uplink payload ===
1362
1363
1364 The Datalog poll reply uplink will use below payload format.
1365
1366 **Retrieval data payload:**
1367
1368 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:480px" %)
1369 |=(% style="width: 60px;background-color:#4F81BD;color:white" %)(((
1370 **Size(bytes)**
1371 )))|=(% style="width: 100px; background-color: rgb(79, 129, 189); color: white;" %)**4**|=(% style="width: 100px; background-color: rgb(79, 129, 189); color: white;" %)**1**|=(% style="width: 220px; background-color: rgb(79, 129, 189); color: white;" %)**Length depends on the return from the commands**
1372 |(% style="width:97px" %)Value|(% style="width:104px" %)Unix Time Stamp|(% style="width:109px" %)Payload Length|(% style="width:165px" %)Data returned by the sensor
1373
1374 **Example:**
1375
1376 If SDI-12-LB has below data inside Flash:
1377
1378 (Soil sensors using the SDI-12 protocol are used for testing.)
1379
1380 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
1381 |=(% style="width: 88px; background-color:#4F81BD;color:white" %)Flash Add|=(% style="width: 98px; background-color: rgb(79, 129, 189); color: white;" %)**Unix Time**|=(% style="width: 82px; background-color: rgb(79, 129, 189); color: white;" %)Payload Length|=(% style="width: 86px; background-color: rgb(79, 129, 189); color: white;" %)**BAT voltage**|=(% style="width: 92px; background-color: rgb(79, 129, 189); color: white;" %)Payload Version|=(% style="width: 64px; background-color:#4F81BD;color:white" %)**Value**
1382 |(% style="width:89px" %)(((
1383 0001
1384 )))|(% style="width:98px" %)(((
1385 2025/3/25 08:09:30
1386 )))|(% style="width:82px" %)5|(% style="width:86px" %)(((
1387 0c a8
1388 )))|(% style="width:92px" %)01|(% style="width:131px" %)(((
1389 08 21
1390 )))
1391 |(% style="width:89px" %)0002|(% style="width:98px" %)(((
1392 2025/3/25 08:10:30
1393 )))|(% style="width:82px" %)5|(% style="width:86px" %)(((
1394 0c ae
1395 )))|(% style="width:92px" %)01|(% style="width:131px" %)(((
1396 08 22
1397 )))
1398 |(% style="width:89px" %)0003|(% style="width:98px" %)(((
1399 2025/3/25 08:11:30
1400 )))|(% style="width:82px" %)5|(% style="width:86px" %)0c ae|(% style="width:92px" %)01|(% style="width:131px" %)08 22
1401 |(% style="width:89px" %)0004|(% style="width:98px" %)(((
1402 2025/3/25 08:12:30
1403 )))|(% style="width:82px" %)5|(% style="width:86px" %)0c ae|(% style="width:92px" %)01|(% style="width:131px" %)08 22
1404 |(% style="width:89px" %)0005|(% style="width:98px" %)(((
1405 2025/3/25 08:13:30
1406 )))|(% style="width:82px" %)5|(% style="width:86px" %)(((
1407 0c b4
1408 )))|(% style="width:92px" %)01|(% style="width:131px" %)08 23
1409 |(% style="width:89px" %)0006|(% style="width:98px" %)(((
1410 2025/3/25 08:14:30
1411 )))|(% style="width:82px" %)5|(% style="width:86px" %)0c ae|(% style="width:92px" %)01|(% style="width:131px" %)08 22
1412 |(% style="width:89px" %)0007|(% style="width:98px" %)(((
1413 2025/3/25 08:15:30
1414 )))|(% style="width:82px" %)5|(% style="width:86px" %)0c b4|(% style="width:92px" %)01|(% style="width:131px" %)08 23
1415 |(% style="width:89px" %)0008|(% style="width:98px" %)(((
1416 2025/3/25 08:16:30
1417 )))|(% style="width:82px" %)5|(% style="width:86px" %)0c ae|(% style="width:92px" %)01|(% style="width:131px" %)08 22
1418
1419 If user sends below downlink command: (% style="background-color:yellow" %)3168253B6E68253E2305
1420
1421 Where : Start time: (% _mstmutation="1" %)68253B6E (%%)= time 2025/05/15 00:55:10
1422
1423 Stop time: (% _mstmutation="1" %)68253E23 (%%)= time 2025/05/15 01:06:43
1424
1425
1426 **SDI-12-LB will uplink this payload.**
1427
1428 **68253B6E 12 0C7801F10D302B312E31372B32362E390D0A **
1429 68253C5D 12 0C7801F10D302B312E31372B32372E340D0A
1430 68253D33 12 0C7201F10D302B312E31352B32382E390D0A
1431 68253DAB 12 0C7201F10D302B312E31342B32392E340D0A
1432 68253E23 12 0C7201F10D302B312E31332B33302E300D0A
1433
1434
1435 Where the first 23 bytes is for the first entry:
1436
1437 **68253B6E 12 0C7801F10D302B312E31372B32362E390D0A**
1438
1439 Unix Time Stamp: 68253B6E(H)=1747270510(D)  ~-~->  time=2025-05-15 8:55:00
1440
1441 Payload Length: 0x12(H)=18 bytes
1442
1443 Battery voltage: 0x0C78(H)=3192 mV
1444
1445 Payload Version:  01
1446
1447 Value: For the distance sensor used for testing, this value is the mm distance value, 0xF10D302B312E31372B32362E390D0A(H)
1448
1449
1450
1451 = 3. Configure SDI-12-LB/LS via AT Command or LoRaWAN Downlink =
1452
1453
1454 Use can configure SDI-12-LB/LS via AT Command or LoRaWAN Downlink.
1455
1456 * AT Command Connection: See [[FAQ>>||anchor="H7.FAQ"]].
1457 * LoRaWAN Downlink instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
1458
1459 There are two kinds of commands to configure SDI-12-LB/LS, they are:
1460
1461 * (% style="color:blue" %)**General Commands**.
1462
1463 These commands are to configure:
1464
1465 * General system settings like: uplink interval.
1466 * LoRaWAN protocol & radio related command.
1467
1468 They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:
1469
1470 [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
1471
1472
1473 * (% style="color:blue" %)**Commands special design for SDI-12-LB/LS**
1474
1475 These commands only valid for SDI-12-LB/LS, as below:
1476
1477
1478 == 3.1 Set Transmit Interval Time ==
1479
1480
1481 Feature: Change LoRaWAN End Node Transmit Interval.
1482
1483 (% style="color:blue" %)**AT Command: AT+TDC**
1484
1485 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
1486 |=(% style="width: 160px; background-color:#4F81BD;color:white" %)**Command Example**|=(% style="width: 160px; background-color:#4F81BD;color:white" %)**Function**|=(% style="width: 190px;background-color:#4F81BD;color:white" %)**Response**
1487 |(% style="background-color:#f2f2f2; width:157px" %)AT+TDC=?|(% style="background-color:#f2f2f2; width:166px" %)Show current transmit Interval|(% style="background-color:#f2f2f2" %)(((
1488 30000
1489 OK
1490 the interval is 30000ms = 30s
1491 )))
1492 |(% style="background-color:#f2f2f2; width:157px" %)AT+TDC=60000|(% style="background-color:#f2f2f2; width:166px" %)Set Transmit Interval|(% style="background-color:#f2f2f2" %)(((
1493 OK
1494 Set transmit interval to 60000ms = 60 seconds
1495 )))
1496
1497 (% style="color:blue" %)**Downlink Command: 0x01**
1498
1499 Format: Command Code (0x01) followed by 3 bytes time value.
1500
1501 If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
1502
1503 * Example 1: Downlink Payload: 0100001E  ~/~/ Set Transmit Interval (TDC) = 30 seconds
1504 * Example 2: Downlink Payload: 0100003C  ~/~/  Set Transmit Interval (TDC) = 60 seconds
1505
1506 == 3.2 Set Interrupt Mode ==
1507
1508
1509 Feature, Set Interrupt mode for GPIO_EXIT.
1510
1511 (% style="color:blue" %)**AT Command: AT+INTMOD**
1512
1513 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
1514 |=(% style="width: 154px;background-color:#4F81BD;color:white" %)**Command Example**|=(% style="width: 196px;background-color:#4F81BD;color:white" %)**Function**|=(% style="width: 160px;background-color:#4F81BD;color:white" %)**Response**
1515 |(% style="background-color:#f2f2f2; width:154px" %)AT+INTMOD=?|(% style="background-color:#f2f2f2; width:196px" %)Show current interrupt mode|(% style="background-color:#f2f2f2; width:157px" %)(((
1516 0
1517 OK
1518 the mode is 0 =Disable Interrupt
1519 )))
1520 |(% style="background-color:#f2f2f2; width:154px" %)AT+INTMOD=2|(% style="background-color:#f2f2f2; width:196px" %)(((
1521 Set Transmit Interval
1522 0. (Disable Interrupt),
1523 ~1. (Trigger by rising and falling edge)
1524 2. (Trigger by falling edge)
1525 3. (Trigger by rising edge)
1526 )))|(% style="background-color:#f2f2f2; width:157px" %)OK
1527
1528 (% style="color:blue" %)**Downlink Command: 0x06**
1529
1530 Format: Command Code (0x06) followed by 3 bytes.
1531
1532 This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
1533
1534 * Example 1: Downlink Payload: 06000000  ~/~/  Turn off interrupt mode
1535 * Example 2: Downlink Payload: 06000003  ~/~/  Set the interrupt mode to rising edge trigger
1536
1537 == 3.3 Set the output time ==
1538
1539
1540 Feature, Control the output 3V3 , 5V or 12V.
1541
1542 (% style="color:blue" %)**AT Command: AT+3V3T**
1543
1544 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:474px" %)
1545 |=(% style="width: 154px;background-color:#4F81BD;color:white" %)**Command Example**|=(% style="width: 201px;background-color:#4F81BD;color:white" %)**Function**|=(% style="width: 120px;background-color:#4F81BD;color:white" %)**Response**
1546 |(% style="background-color:#f2f2f2; width:154px" %)AT+3V3T=?|(% style="background-color:#f2f2f2; width:201px" %)Show 3V3 open time.|(% style="background-color:#f2f2f2; width:116px" %)(((
1547 0
1548 OK
1549 )))
1550 |(% style="background-color:#f2f2f2; width:154px" %)AT+3V3T=0|(% style="background-color:#f2f2f2; width:201px" %)Normally open 3V3 power supply.|(% style="background-color:#f2f2f2; width:116px" %)(((
1551 OK
1552 default setting
1553 )))
1554 |(% style="background-color:#f2f2f2; width:154px" %)AT+3V3T=1000|(% style="background-color:#f2f2f2; width:201px" %)Close after a delay of 1000 milliseconds.|(% style="background-color:#f2f2f2; width:116px" %)(((
1555 OK
1556 )))
1557 |(% style="background-color:#f2f2f2; width:154px" %)AT+3V3T=65535|(% style="background-color:#f2f2f2; width:201px" %)Normally closed 3V3 power supply.|(% style="background-color:#f2f2f2; width:116px" %)(((
1558 OK
1559 )))
1560
1561 (% style="color:blue" %)**AT Command: AT+5VT**
1562
1563 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:470px" %)
1564 |=(% style="width: 155px;background-color:#4F81BD;color:white" %)**Command Example**|=(% style="width: 196px;background-color:#4F81BD;color:white" %)**Function**|=(% style="width: 119px;background-color:#4F81BD;color:white" %)**Response**
1565 |(% style="background-color:#f2f2f2; width:155px" %)AT+5VT=?|(% style="background-color:#f2f2f2; width:196px" %)Show 5V open time.|(% style="background-color:#f2f2f2; width:114px" %)(((
1566 0
1567 OK
1568 )))
1569 |(% style="background-color:#f2f2f2; width:155px" %)AT+5VT=0|(% style="background-color:#f2f2f2; width:196px" %)Normally closed 5V power supply.|(% style="background-color:#f2f2f2; width:114px" %)(((
1570 OK
1571 default setting
1572 )))
1573 |(% style="background-color:#f2f2f2; width:155px" %)AT+5VT=1000|(% style="background-color:#f2f2f2; width:196px" %)Close after a delay of 1000 milliseconds.|(% style="background-color:#f2f2f2; width:114px" %)(((
1574 OK
1575 )))
1576 |(% style="background-color:#f2f2f2; width:155px" %)AT+5VT=65535|(% style="background-color:#f2f2f2; width:196px" %)Normally open 5V power supply.|(% style="background-color:#f2f2f2; width:114px" %)(((
1577 OK
1578 )))
1579
1580 (% style="color:blue" %)**AT Command: AT+12VT **
1581
1582 (% style="color:blue" %)**(The v1.2 version is enabled for 1 second by default, and the version below v1.2 is disabled by default)**
1583
1584 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:443px" %)
1585 |=(% style="width: 156px;background-color:#4F81BD;color:white" %)**Command Example**|=(% style="width: 199px;background-color:#4F81BD;color:white" %)**Function**|=(% style="width: 89px;background-color:#4F81BD;color:white" %)**Response**
1586 |(% style="background-color:#f2f2f2; width:156px" %)AT+12VT=?|(% style="background-color:#f2f2f2; width:199px" %)Show 12V open time.|(% style="background-color:#f2f2f2; width:83px" %)(((
1587 0
1588 OK
1589 )))
1590 |(% style="background-color:#f2f2f2; width:156px" %)AT+12VT=0|(% style="background-color:#f2f2f2; width:199px" %)Normally closed 12V power supply.|(% style="background-color:#f2f2f2; width:83px" %)OK
1591 |(% style="background-color:#f2f2f2; width:156px" %)AT+12VT=500|(% style="background-color:#f2f2f2; width:199px" %)Close after a delay of 500 milliseconds.|(% style="background-color:#f2f2f2; width:83px" %)(((
1592 OK
1593 )))
1594
1595 (% style="color:blue" %)**Downlink Command: 0x07**
1596
1597 Format: Command Code (0x07) followed by 3 bytes.
1598
1599 The first byte is which power, the second and third bytes are the time to turn on.
1600
1601 * Example 1: Downlink Payload: 070101F4  **~-~-->**  AT+3V3T=500
1602 * Example 2: Downlink Payload: 0701FFFF   **~-~-->**  AT+3V3T=65535
1603 * Example 3: Downlink Payload: 070203E8  **~-~-->**  AT+5VT=1000
1604 * Example 4: Downlink Payload: 07020000  **~-~-->**  AT+5VT=0
1605 * Example 5: Downlink Payload: 070301F4  **~-~-->**  AT+12VT=500
1606 * Example 6: Downlink Payload: 07030000  **~-~-->**  AT+12VT=0
1607
1608 == 3.4 Set the all data mode ==
1609
1610
1611 Feature, Set the all data mode.
1612
1613 (% style="color:blue" %)**AT Command: AT+ALLDATAMOD**
1614
1615 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:437px" %)
1616 |=(% style="background-color:#4F81BD;color:white" %)**Command Example**|=(% style="background-color:#4F81BD;color:white" %)**Function**|=(% style="background-color:#4F81BD;color:white" %)**Response**
1617 |(% style="background-color:#f2f2f2" %)AT+ALLDATAMOD=?|(% style="background-color:#f2f2f2" %)Show current all data mode|(% style="background-color:#f2f2f2" %)(((
1618 0
1619 OK
1620 )))
1621 |(% style="background-color:#f2f2f2" %)AT+ALLDATAMOD=1|(% style="background-color:#f2f2f2" %)Set all data mode is 1.|(% style="background-color:#f2f2f2" %)OK
1622
1623 (% style="color:blue" %)**Downlink Command: 0xAB**
1624
1625 Format: Command Code (0xAB) followed by 1 bytes.
1626
1627 * Example 1: Downlink Payload: AB 00  ~/~/  AT+ALLDATAMOD=0
1628 * Example 2: Downlink Payload: AB 01  ~/~/  AT+ALLDATAMOD=1
1629
1630 == 3.5 Set the splicing payload for uplink ==
1631
1632
1633 Feature, splicing payload for uplink.
1634
1635 (% style="color:blue" %)**AT Command: AT+DATAUP**
1636
1637 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
1638 |=(% style="width: 154px;background-color:#4F81BD;color:white" %)**Command Example**|=(% style="width: 266px;background-color:#4F81BD;color:white" %)**Function**|=(% style="background-color:#4F81BD;color:white" %)**Response**
1639 |(% style="background-color:#f2f2f2; width:154px" %)AT+DATAUP =?|(% style="background-color:#f2f2f2; width:266px" %)Show current splicing payload for uplink mode|(% style="background-color:#f2f2f2" %)(((
1640 0
1641 OK
1642 )))
1643 |(% style="background-color:#f2f2f2; width:154px" %)AT+DATAUP =0|(% style="background-color:#f2f2f2; width:266px" %)(((
1644 Set splicing payload for uplink mode is 0.
1645 )))|(% style="background-color:#f2f2f2" %)(((
1646 OK
1647 )))
1648 |(% style="background-color:#f2f2f2; width:154px" %)AT+DATAUP =1|(% style="background-color:#f2f2f2; width:266px" %)Set splicing payload for uplink mode is 1 , and the each splice uplink is sent sequentially.|(% style="background-color:#f2f2f2" %)OK
1649 |(% style="background-color:#f2f2f2; width:154px" %)AT+DATAUP =1,20000|(% style="background-color:#f2f2f2; width:266px" %)(((
1650 Set splicing payload for uplink mode is 1, and the uplink interval of each splice to 20000 milliseconds.
1651 )))|(% style="background-color:#f2f2f2" %)OK
1652
1653 (% style="color:blue" %)**Downlink Command: 0xAD**
1654
1655 Format: Command Code (0xAD) followed by 1 bytes or 5 bytes.
1656
1657 * Example 1: Downlink Payload: AD 00  ~/~/  AT+DATAUP=0
1658 * Example 2: Downlink Payload: AD 01  ~/~/  AT+DATAUP =1
1659 * Example 3: Downlink Payload: AD 01 00 00 14  ~/~/  AT+DATAUP =1,20000
1660
1661 This means that the interval is set to 0x000014=20S
1662
1663
1664 == 3.6 Set the payload version ==
1665
1666
1667 Feature, Set the payload version.
1668
1669 (% style="color:blue" %)**AT Command: AT+PAYVER**
1670
1671 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:437px" %)
1672 |=(% style="width: 158px;background-color:#4F81BD;color:white" %)**Command Example**|=(% style="width: 192px;background-color:#4F81BD;color:white" %)**Function**|=(% style="background-color:#4F81BD;color:white" %)**Response**
1673 |(% style="background-color:#f2f2f2; width:158px" %)AT+PAYVER=?|(% style="background-color:#f2f2f2; width:192px" %)Show current payload version|(% style="background-color:#f2f2f2" %)(((
1674 1
1675 OK
1676 )))
1677 |(% style="background-color:#f2f2f2; width:158px" %)AT+PAYVER=5|(% style="background-color:#f2f2f2; width:192px" %)Set payload version is 5.|(% style="background-color:#f2f2f2" %)OK
1678
1679 (% style="color:blue" %)**Downlink Command: 0xAE**
1680
1681 Format: Command Code (0xAE) followed by 1 bytes.
1682
1683 * Example 1: Downlink Payload: AE 01  ~/~/  AT+PAYVER=1
1684 * Example 2: Downlink Payload: AE 05  ~/~/  AT+PAYVER=5
1685
1686 == 3.7 Print data entries base on page(Since v1.3.0) ==
1687
1688
1689 Feature: Print the sector data from start page to stop page (max is 416 pages).
1690
1691 (% style="color:#4f81bd" %)**AT Command: AT+PDTA**
1692
1693 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
1694 |(% style="background-color:#4f81bd; color:white; width:158px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:352px" %)**Function**
1695 |(% style="width:156px" %)(((
1696 AT+PDTA=1,2
1697 Print page 1 to 2
1698 )))|(% style="width:311px" %)(((
1699 Stop Tx and RTP events when read sensor data
1700
1701 8033330 2025/5/14 12:27:32 18 0c 84 01 f1 0d 30 2b 31 2e 30
1702
1703 8033340 38 2b 32 34 2e 36 0d 0a
1704
1705 8033350 2025/5/14 12:29:32 18 0c 72 01 f1 0d 30 2b 31 2e 30
1706
1707 8033360 38 2b 32 34 2e 36 0d 0a
1708
1709 8033370 2025/5/14 12:31:32 18 0c 78 01 f1 0d 30 2b 31 2e 30
1710
1711 8033380 38 2b 32 34 2e 36 0d 0a
1712
1713 8033390 2025/5/14 12:33:32 18 0c 72 01 f1 0d 30 2b 31 2e 30
1714
1715 80333A0 38 2b 32 34 2e 36 0d 0a
1716
1717 80333B0 2025/5/14 12:35:32 18 0c 72 01 f1 0d 30 2b 31 2e 30
1718
1719 80333C0 38 2b 32 34 2e 36 0d 0a
1720
1721
1722 OK
1723 )))
1724
1725 (% style="color:#4f81bd" %)**Downlink Command:**
1726
1727 No downlink commands for feature
1728
1729
1730 == 3.8 Print last few data entries(Since v1.3.0) ==
1731
1732
1733 Feature: Print the last few data entries
1734
1735 (% style="color:#4f81bd" %)**AT Command: AT+PLDTA**
1736
1737 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:437px" %)
1738 |=(% style="width: 158px;background-color:#4F81BD;color:white" %)**Command Example**|=(% style="width: 192px;background-color:#4F81BD;color:white" %)**Function**
1739 |(% style="background-color:#f2f2f2; width:158px" %)AT+PLDTA=10,0|(% style="background-color:#f2f2f2; width:192px" %)Printing the last ten data in hex format
1740 |(% style="background-color:#f2f2f2; width:158px" %)AT+PLDTA=10,1|(% style="background-color:#f2f2f2; width:192px" %)Print the last ten data in string format
1741
1742 * **Prints in hex format:**
1743
1744 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
1745 |(% style="background-color:#4f81bd; color:white; width:158px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:352px" %)**Function**
1746 |(% style="width:156px" %)(((
1747 AT+PLDTA=10,0
1748 Print last 10 entries
1749 )))|(% style="width:311px" %)(((
1750 Stop Tx events when read sensor data
1751
1752 0001-0001 2025/5/16 06:48:04 7 0c 7e 01 00 5f 01 05
1753
1754 0002-0002 2025/5/16 06:50:04 7 0c 72 01 00 5f 01 05
1755
1756 0003-0003 2025/5/16 06:52:04 7 0c 72 01 00 5f 01 05
1757
1758 0004-0004 2025/5/16 06:54:04 7 0c 7e 01 00 5f 01 05
1759
1760 0005-0005 2025/5/16 06:56:04 7 0c 7e 01 00 5f 01 07
1761
1762 0006-0006 2025/5/16 06:58:04 7 0c 8a 01 00 60 01 07
1763
1764 0007-0007 2025/5/16 07:00:04 7 0c 84 01 00 61 01 07
1765
1766 0008-0008 2025/5/16 07:02:04 7 0c 72 01 00 61 01 07
1767
1768 0009-0009 2025/5/16 07:04:04 7 0c 78 01 00 61 01 07
1769
1770 0010-0010 2025/5/16 07:06:04 7 0c 78 01 00 61 01 07
1771
1772 Start Tx events
1773
1774 OK
1775 )))
1776
1777 * **Printing in String Format:**
1778
1779 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
1780 |(% style="background-color:#4f81bd; color:white; width:158px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:352px" %)**Function**
1781 |(% style="width:156px" %)(((
1782 AT+PLDTA=10,1
1783 Print last 10 entries
1784
1785 (((
1786 (Printing in String Format)
1787 )))
1788 )))|(% style="width:311px" %)(((
1789 Stop Tx events when read sensor data
1790
1791 0001-0001 2025/5/16 06:48:04 7 ~~_
1792
1793 0002-0002 2025/5/16 06:50:04 7 r_
1794
1795 0003-0003 2025/5/16 06:52:04 7 r_
1796
1797 0004-0004 2025/5/16 06:54:04 7 ~~_
1798
1799 0005-0005 2025/5/16 06:56:04 7 ~~_
1800
1801 0006-0006 2025/5/16 06:58:04 7 `
1802
1803 0007-0007 2025/5/16 07:00:04 7 a
1804
1805 0008-0008 2025/5/16 07:02:04 7 ra
1806
1807 0009-0009 2025/5/16 07:04:04 7 xa
1808
1809 0010-0010 2025/5/16 07:06:04 7 xa
1810
1811 Start Tx events
1812
1813 OK
1814 )))
1815
1816 (% style="color:#4f81bd" %)**Downlink Command:**
1817
1818 No downlink commands for feature
1819
1820
1821 == 3.9 Clear Flash Record(Since v1.3.0) ==
1822
1823
1824 Feature: Clear flash storage for data log feature.
1825
1826 (% style="color:#4f81bd" %)**AT Command: AT+CLRDTA**
1827
1828 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:503px" %)
1829 |(% style="background-color:#4f81bd; color:white; width:157px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:137px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:209px" %)**Response**
1830 |(% style="width:155px" %)AT+CLRDTA |(% style="width:134px" %)Clear date record|(% style="width:209px" %)(((
1831 Clear all stored sensor data…
1832
1833 OK
1834 )))
1835
1836 (% style="color:#4f81bd" %)**Downlink Command: 0xA3**
1837
1838 * Example: 0xA301  ~/~/  Same as AT+CLRDTA
1839
1840 == 3.10 SDI12 timing(Since v1.3.0) ==
1841
1842
1843 Feature: Get or set the time of SDI12 timing.
1844
1845 [[image:1747289896656-580.png||height="414" width="566"]]
1846
1847
1848 (% style="color:#4f81bd" %)**AT Command: AT+SDITIMING**
1849
1850 (% border="1" cellspacing="3" style="background-color:#f2f2f2; width:503px" %)
1851 |(% style="background-color:#4f81bd; color:white; width:157px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:167px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:177px" %)**Response**
1852 |(% style="width:155px" %)(((
1853 AT+SDITIMING=13,9
1854
1855
1856 )))|(% style="width:167px" %)Get or set the time of SDI12 timing|(% style="width:177px" %)(((
1857 OK
1858
1859 Default: 13,9
1860 )))
1861
1862 (% style="color:#4f81bd" %)**Downlink Command: 0xA9**
1863
1864 * Example: 0xA90D09  ~/~/  Same as AT+SDITIMING=13,9
1865
1866
1867
1868
1869 == 3.11 add Pulse_count, VDC_input, IDC_input(Since firmware V1.3.0) ==
1870
1871
1872 (% style="color:blue" %)**Setting up external sensors:**
1873
1874 * (% style="color:#037691" %)**AT Command:**
1875
1876 (% style="color:#4472c4" %)**AT+EXT=a,b,c**(%%)
1877
1878 (% style="color:#4472c4" %)**a:**(%%)  **0:** Disable Counting function ( doesn't effect interrupt ).  **1:** Enable Counting function(4 bytes).
1879 (% style="color:#4472c4" %)**b: **(%%) **0:** Disable voltage acquisition function.  **1:** Enable voltage acquisition function(2 bytes)
1880 (% style="color:#4472c4" %)**c:**(%%)  **0:** Disable current acquisition  function.  **1:** Enable current acquisition function(2 bytes).
1881
1882 **Example:**
1883
1884 (% style="color:#4472c4" %)**AT+EXT=1,1,1**
1885
1886 Device will add counting, voltage and current acquisition function.
1887
1888 The payload will be:
1889 Battery(mV) & Interrupt _Flag + PAYLOAD_VER + ***counting + ** ***VDC_INPUT**  + ***IDC_INPUT**  + Length depends on the return from the commands
1890
1891 (% style="color:#4472c4" %)**AT+EXT=1,0,0**
1892
1893 Device will add counting support.
1894
1895 The payload will be:
1896 Battery(mV) & Interrupt _Flag + PAYLOAD_VER + ***counting** + Length depends on the return from the commands
1897
1898 * (% style="color:#037691" %)**Downlink Command: 0x0B aa bb cc**
1899
1900 Format: Command Code (0x0B) followed by 3 bytes.
1901
1902 (% style="color:#037691" %)**aa:**(%%) Set Disable or Enable Counting Support.   **00**: Disable, **01**: Enable.
1903
1904 (% style="color:#037691" %)**bb:**(%%) Set Disable or Enable voltage acquisition.  **00**: Disable, **01**: Enable.
1905
1906 (% style="color:#037691" %)**cc:**(%%) Set Disable or Enable current acquisition.  **00**: Disable, **01**: Enable.
1907
1908 **Example:**
1909
1910 Downlink payload:  0B 00 00 01  ~/~/AT+EXT=0,0,1  Enable current acquisition
1911
1912 Downlink payload:  0B 01 00 01  ~/~/AT+EXT=1,0,1  Enable Counting Support and Current acquisition                        
1913
1914
1915 (% style="color:blue" %)**Set the pulse count value:**
1916
1917 * (% style="color:#037691" %)**AT Command:**
1918
1919 (% style="color:#4472c4" %)**AT+SETCNT=aa     **(%%)~/~/ Set the pulse count value.
1920
1921 **Example:**
1922
1923 AT+SETCNT=100  (% style="display:none" %) (%%)~/~/ Set the pulse count to 100.(% style="display:none" %)
1924
1925 * (% style="color:#037691" %)**Downlink Command: 0x0C**
1926
1927 Format: Command Code (0x0C) followed by 4 bytes.
1928
1929 **Example:**
1930
1931 Downlink Payload: 0C 00 00 00 64  ~/~/ AT+SETCNT=100
1932
1933
1934 (% style="color:blue" %)**Connect counting sensor:**
1935
1936 The counting sensor cables are connected to the **3V3 pin** and **GPIO_EXTI** pin of the **SIB v1.3** motherboard.
1937
1938 [[image:image-20250519110640-1.jpeg||height="318" width="708"]]
1939
1940
1941 (% id="cke_bm_1699404S" style="color:blue; display:none" %)** **(% style="color:blue" %)**Connect Voltage output sensor:**
1942
1943 Example:
1944
1945 **RED <~-~-~-~-> VDC_INPUT**
1946
1947 **BLACK <~-~-~-~-~-~-> GND**
1948
1949 [[image:image-20250519111415-3.jpeg||height="338" width="710"]]
1950
1951
1952 (% style="color:blue" %)**Connect Current output sensor:**
1953
1954 Example:
1955
1956 **RED <~-~-~-~-~-~-~-~--> IDC_INPUT**
1957
1958 **BLACK <~-~-~-~-~-~-> GND**
1959
1960 [[image:image-20250519111732-4.jpeg||height="373" width="708"]]
1961
1962
1963
1964 == 3.12 Cut data separation processing(Since firmware V1.3.2) ==
1965
1966
1967 AT+NEWLINE command, which only takes effect when AT+DATAUP=1 or AT+DATAUP=1, timeout.
1968
1969 When not set, each part of AT+DATAUP is sent according to the maximum number of bytes of DR.
1970
1971 When setting, each part of AT+DATAUP is sent according to the value set by AT+NEWLINE.
1972
1973
1974 * (((
1975 (% style="color:#037691" %)** AT Command:**
1976 )))
1977
1978 (% style="color:#4472c4" %)//**AT+NEWLINE=ALL**//(%%)//   //The data cut out by each AT+COMMANDx command is sent separately as an uplink.
1979
1980 (% style="color:#4472c4" %)//**AT+NEWLINE=ALL**//(%%)//   equal：  (% style="color:#4472c4" %)**AT+NEWLINE=1+2+3+4+5+6+7+8+9+10+11+12+13+14+15**//
1981
1982
1983 (% style="color:#4472c4" %)//**AT+NEWLINE=a+b+c**//(%%)//  //The data returned by all commands is divided into three parts, COMMAND(1~~a) is the first part, COMMAND(a+1~~b) is the second part,COMMAND(b+1~~c) is the third part.
1984
1985
1986 (% style="color:#4472c4" %)//**AT+NEWLINE=NULL**//(%%)//  //Turn off the functionality of this AT command.
1987
1988
1989 * (((
1990 (% style="color:#037691" %)** Downlink Payload:**
1991 )))
1992
1993 //AT+NEWLINE=ALL  ~-~-->  (% style="color:#4472c4" %)**0xA5 01**//
1994
1995 // AT+NEWLINE= NULL  ~-~-->  (% style="color:#4472c4" %)**0xA5 00**//
1996
1997 //AT+NEWLINE= a+b+c   ~-~-->  (% style="color:#4472c4" %)**0xA5 number of bytes a b c**//
1998
1999 //AT+NEWLINE= 1+5+15 ~-~-->  (% style="color:#4472c4" %)**0xA5 03 01 05 0F**//
2000
2001
2002
2003 = 4. Battery & Power Consumption =
2004
2005
2006 SDI-12-LB use ER26500 + SPC1520 battery pack and SDI-12-LS use 3000mAh Recharable Battery with Solar Panel. See below link for detail information about the battery info and how to replace.
2007
2008 [[**Battery Info & Power Consumption Analyze**>>url:http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
2009
2010
2011 = 5. Remote Configure device =
2012
2013 == 5.1 Connect via BLE ==
2014
2015
2016 Please see this instruction for how to configure via BLE: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]]
2017
2018
2019 == 5.2 AT Command Set ==
2020
2021
2022
2023 = 6. OTA firmware update =
2024
2025 User can change firmware TS01-LB/LS to:
2026
2027 * Change Frequency band/ region.
2028 * Update with new features.
2029 * Fix bugs.
2030
2031 Firmware and changelog can be downloaded from : [[**Firmware download link**>>https://www.dropbox.com/scl/fo/ztlw35a9xbkomu71u31im/AMbGiR5K1fLcUTLbp44o22Q/LoRaWAN%20End%20Node/SDI-12-LB/Firmware?rlkey=ojjcsw927eaow01dgooldq3nu&subfolder_nav_tracking=1&dl=0]]
2032
2033 Methods to Update Firmware:
2034
2035 * (Recommanded way) OTA firmware update via wireless : **[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]**
2036
2037 * Update through UART TTL interface : **[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.
2038
2039
2040
2041 = 7. FAQ =
2042
2043 == 7.1 How to use AT Command  via UART to access device? ==
2044
2045
2046 See: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]
2047
2048
2049 == 7.2 How to update firmware via UART port? ==
2050
2051
2052 See: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]
2053
2054
2055 == 7.3 How to change the LoRa Frequency Bands/Region? ==
2056
2057
2058 You can follow the instructions for [[how to upgrade image>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome]].
2059 When downloading the images, choose the required image file for download. ​
2060
2061
2062 == 7.4 Why is the data uploaded to the LoRaWAN platform node empty and fProt~=0? ==
2063
2064
2065 This is due to The length of bytes sent by the node is limited by the lorawan protocol, and the fixed DR needs to be adjusted to improve this problem.
2066
2067 Please refer to the following link for the number of bytes limited by different frequencies and different DRs in the lorawan protocol
2068
2069 [[lora-alliance.org/wp-content/uploads/2021/05/RP002-1.0.3-FINAL-1.pdf>>url:https://lora-alliance.org/wp-content/uploads/2021/05/RP002-1.0.3-FINAL-1.pdf]]
2070
2071 Example:
2072
2073 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/RS485-LN%20%E2%80%93%20RS485%20to%20LoRaWAN%20Converter/WebHome/image-20240620145456-1.png?rev=1.1||alt="image-20240620145456-1.png"]]
2074
2075 Please refer to the following command to fix DR
2076
2077 AT+ADR=0
2078
2079 AT+DR=3
2080
2081 Downlink command:
2082
2083 [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H7.4DataRate>>url:http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H7.4DataRate]]
2084
2085
2086 = 8. ​Order Info =
2087
2088
2089 (((
2090 **Part Number: (% style="color:blue" %)SDI-12-LB-XX-YY(%%) or (% style="color:blue" %)SDI-12-LS-XX-YY(%%)**
2091 )))
2092
2093 (((
2094 (% style="color:blue" %)**XX**(%%): The default frequency band
2095 )))
2096
2097 (((
2098 * (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band
2099 * (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band
2100 * (% style="color:red" %)**EU433**(%%): LoRaWAN EU433 band
2101 * (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band
2102 * (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band
2103 * (% style="color:red" %)**US915**(%%): LoRaWAN US915 band
2104 * (% style="color:red" %)**IN865**(%%): LoRaWAN IN865 band
2105 * (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
2106 )))
2107
2108 (% style="color:blue" %)**YY: **(%%)The grand connector hole size
2109
2110 * M12: M12 hole
2111 * M16: M16 hole
2112
2113 = 9. Packing Info =
2114
2115
2116 (% style="color:#037691" %)**Package Includes**:
2117
2118 * SDI-12-LB or SDI-12-LS SDI-12 to LoRaWAN Converter x 1
2119
2120 (% style="color:#037691" %)**Dimension and weight**:
2121
2122 * Device Size: cm
2123 * Device Weight: g
2124 * Package Size / pcs : cm
2125 * Weight / pcs : g
2126
2127 = 10. ​Support =
2128
2129
2130 * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
2131
2132 * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]