Wiki source code of SDI-12-LB/LS -- SDI-12 to LoRaWAN Converter User Manual

Version 100.1 by kai on 2024/05/25 10:43

version	line-number	content
90.2	1
	2
40.7	3	(% style="text-align:center" %)
90.16	4	[[image:image-20240103165259-3.png\|\|height="433" width="591"]]
2.2	5
90.2	6
	7
	8
	9
	10
	11
87.8	12	Table of Contents:
2.2	13
40.7	14	{{toc/}}
2.2	15
	16
	17
	18
	19
	20
	21
	22
	23
	24
	25
	26
	27
9.2	28	= 1. Introduction =
2.2	29
9.2	30	== 1.1 What is SDI-12 to LoRaWAN Converter ==
2.2	31
	32
41.13	33	(((
90.3	34	The Dragino (% style="color:blue" %)SDI-12-LB/LS(%%) is a (% style="color:blue" %)SDI-12 to LoRaWAN Converter (%%)designed for Smart Agriculture solution.
41.13	35	)))
9.2	36
41.13	37	(((
2.2	38	SDI-12 (Serial Digital Interface at 1200 baud) is an asynchronous [[serial communications>>url:https://en.wikipedia.org/wiki/Serial_communication]] protocol for intelligent sensors that monitor environment data. SDI-12 protocol is widely used in Agriculture sensor and Weather Station sensors.
41.13	39	)))
2.2	40
41.13	41	(((
90.3	42	SDI-12-LB/LS has SDI-12 interface and support 12v output to power external SDI-12 sensor. It can get the environment data from SDI-12 sensor and sends out the data via LoRaWAN wireless protocol.
41.13	43	)))
2.2	44
41.13	45	(((
90.3	46	The LoRa wireless technology used in SDI-12-LB/LS allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
41.13	47	)))
2.2	48
41.13	49	(((
90.3	50	SDI-12-LB/LS is powered by (% style="color:blue" %)8500mAh Li-SOCI2 battery(%%) or (% style="color:blue" %)solar powered + li-on battery(%%) it is designed for long term use up to 5 years.
41.13	51	)))
2.2	52
41.13	53	(((
90.3	54	Each SDI-12-LB/LS is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
41.13	55	)))
2.2	56
	57
47.1	58	[[image:image-20230201084414-1.png\|\|_mstalt="427765" height="464" width="1108"]]
2.2	59
	60
9.2	61	== 1.2 Features ==
	62
	63
2.2	64	* LoRaWAN 1.0.3 Class A
	65	* Ultra-low power consumption
43.1	66	* Controllable 3.3v, 5v and 12v output to power external sensor
2.2	67	* SDI-12 Protocol to connect to SDI-12 Sensor
	68	* Monitor Battery Level
	69	* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
	70	* Support Bluetooth v5.1 and LoRaWAN remote configure.
	71	* Support wireless OTA update firmware
	72	* Uplink on periodically
	73	* Downlink to change configure
90.5	74	* 8500mAh Li/SOCl2 Battery (SDI-12-LB)
	75	* Solar panel + 3000mAh Li-on battery (SDI-12-LS)
2.2	76
9.2	77	== 1.3 Specification ==
2.2	78
	79
40.2	80	(% style="color:#037691" %)Micro Controller:
2.2	81
	82	* MCU: 48Mhz ARM
	83	* Flash: 256KB
	84	* RAM: 64KB
	85
40.2	86	(% style="color:#037691" %)Common DC Characteristics:
2.2	87
90.5	88	* Supply Voltage: Built-in Battery, 2.5v ~~ 3.6v
87.2	89	* Support current: 5V 300mA, 12V 100mA
2.2	90	* Operating Temperature: -40 ~~ 85°C
	91
40.2	92	(% style="color:#037691" %)LoRa Spec:
2.2	93
	94	* Frequency Range, Band 1 (HF): 862 ~~ 1020 Mhz
	95	* Max +22 dBm constant RF output vs.
	96	* RX sensitivity: down to -139 dBm.
	97	* Excellent blocking immunity
	98
40.2	99	(% style="color:#037691" %)Current Input Measuring :
2.2	100
	101	* Range: 0 ~~ 20mA
	102	* Accuracy: 0.02mA
	103	* Resolution: 0.001mA
	104
40.2	105	(% style="color:#037691" %)Voltage Input Measuring:
2.2	106
	107	* Range: 0 ~~ 30v
	108	* Accuracy: 0.02v
	109	* Resolution: 0.001v
	110
40.2	111	(% style="color:#037691" %)Battery:
2.2	112
	113	* Li/SOCI2 un-chargeable battery
	114	* Capacity: 8500mAh
	115	* Self-Discharge: <1% / Year @ 25°C
	116	* Max continuously current: 130mA
	117	* Max boost current: 2A, 1 second
	118
40.2	119	(% style="color:#037691" %)Power Consumption
2.2	120
	121	* Sleep Mode: 5uA @ 3.3v
	122	* LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm
	123
9.2	124	== 1.4 Connect to SDI-12 Sensor ==
2.2	125
	126
47.1	127	[[image:1675212538524-889.png\|\|_mstalt="298272"]]
2.2	128
	129
9.2	130	== 1.5 Sleep mode and working mode ==
2.2	131
	132
40.2	133	(% style="color:blue" %)Deep Sleep Mode: (%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.
2.2	134
40.2	135	(% style="color:blue" %)Working Mode: (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.
2.2	136
	137
9.2	138	== 1.6 Button & LEDs ==
2.2	139
	140
90.7	141	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/RS485-LB_Waterproof_RS485UART_to_LoRaWAN_Converter/WebHome/image-20240103160425-4.png?rev=1.1\|\|alt="image-20240103160425-4.png"]]
2.2	142
90.12	143	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
	144	\|=(% style="width: 167px;background-color:#4F81BD;color:white" %)Behavior on ACT\|=(% style="width: 117px;background-color:#4F81BD;color:white" %)Function\|=(% style="width: 226px;background-color:#4F81BD;color:white" %)Action
48.3	145	\|(% style="background-color:#f2f2f2; width:167px" %)Pressing ACT between 1s < time < 3s\|(% style="background-color:#f2f2f2; width:117px" %)Send an uplink\|(% style="background-color:#f2f2f2; width:225px" %)(((
9.2	146	If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, (% style="color:blue" %)blue led (%%)will blink once.
2.2	147	Meanwhile, BLE module will be active and user can connect via BLE to configure device.
	148	)))
48.3	149	\|(% style="background-color:#f2f2f2; width:167px" %)Pressing ACT for more than 3s\|(% style="background-color:#f2f2f2; width:117px" %)Active Device\|(% style="background-color:#f2f2f2; width:225px" %)(((
	150	(% style="background-color:#f2f2f2; color:green" %)Green led(%%) will fast blink 5 times, device will enter (% style="color:#037691" %)OTA mode(%%) for 3 seconds. And then start to JOIN LoRaWAN network.
	151	(% style="background-color:#f2f2f2; color:green" %)Green led(%%) will solidly turn on for 5 seconds after joined in network.
2.2	152	Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device join or not join LoRaWAN network.
	153	)))
48.3	154	\|(% style="background-color:#f2f2f2; width:167px" %)Fast press ACT 5 times.\|(% style="background-color:#f2f2f2; width:117px" %)Deactivate Device\|(% style="background-color:#f2f2f2; width:225px" %)(% style="color:red" %)Red led(%%) will solid on for 5 seconds. Means PS-LB-NA is in Deep Sleep Mode.
2.2	155
9.2	156	== 1.7 Pin Mapping ==
2.2	157
	158
47.1	159	[[image:1675213198663-754.png\|\|_mstalt="297167"]]
2.2	160
	161
9.2	162	== 1.8 BLE connection ==
2.2	163
9.2	164
90.4	165	SDI-12-LB/LS support BLE remote configure.
2.2	166
	167	BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:
	168
	169	* Press button to send an uplink
	170	* Press button to active device.
	171	* Device Power on or reset.
	172
	173	If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.
	174
	175
9.2	176	== 1.9 Mechanical ==
2.2	177
90.6	178	=== 1.9.1 for LB version ===
2.2	179
90.7	180
47.1	181	[[image:image-20230201090139-2.png\|\|_mstalt="428623"]]
2.2	182
47.1	183	[[image:image-20230201090139-3.png\|\|_mstalt="428987"]]
2.2	184
47.1	185	[[image:image-20230201090139-4.png\|\|_mstalt="429351"]]
2.2	186
	187
90.6	188	=== 1.9.2 for LS version ===
	189
	190
	191	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SN50v3-LB/WebHome/image-20231231203439-3.png?width=886&height=385&rev=1.1\|\|alt="image-20231231203439-3.png"]]
	192
	193
19.2	194	= 2. Configure SDI-12 to connect to LoRaWAN network =
9.2	195
19.2	196	== 2.1 How it works ==
9.2	197
	198
90.4	199	The SDI-12-LB/LS is configured as (% style="color:#037691" %)LoRaWAN OTAA Class A(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and activate the SDI-12-LB/LS. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
9.2	200
2.2	201
19.2	202	== 2.2 Quick guide to connect to LoRaWAN server (OTAA) ==
2.2	203
	204
	205	Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.
	206
	207
47.1	208	[[image:image-20230201090528-5.png\|\|_mstalt="430300" height="465" width="1111"]]
2.2	209
	210
	211	The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
	212
	213
90.4	214	(% style="color:blue" %)Step 1(%%): Create a device in TTN with the OTAA keys from SDI-12-LB/LS.
2.2	215
90.4	216	Each SDI-12-LB/LS is shipped with a sticker with the default device EUI as below:
2.2	217
49.3	218	[[image:image-20230426084456-1.png\|\|height="241" width="519"]]
2.2	219
	220
	221	You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
	222
	223
40.2	224	(% style="color:blue" %)Register the device
2.2	225
47.1	226	[[image:1675213652444-622.png\|\|_mstalt="293657"]]
2.2	227
	228
40.2	229	(% style="color:blue" %)Add APP EUI and DEV EUI
2.2	230
	231
47.1	232	[[image:1675213661769-223.png\|\|_mstalt="295217"]]
2.2	233
	234
40.2	235	(% style="color:blue" %)Add APP EUI in the application
2.2	236
	237
47.1	238	[[image:1675213675852-577.png\|\|_mstalt="297947"]]
2.2	239
	240
40.2	241	(% style="color:blue" %)Add APP KEY
2.2	242
47.1	243	[[image:1675213686734-883.png\|\|_mstalt="298064"]]
2.2	244
	245
90.4	246	(% style="color:blue" %)Step 2(%%): Activate on SDI-12-LB/LS
2.2	247
	248
90.4	249	Press the button for 5 seconds to activate the SDI-12-LB/LS.
2.2	250
40.2	251	(% style="color:green" %)Green led(%%) will fast blink 5 times, device will enter (% style="color:blue" %)OTA mode (%%)for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)Green led(%%) will solidly turn on for 5 seconds after joined in network.
2.2	252
	253
47.1	254	[[image:1675213704414-644.png\|\|_mstalt="293748"]]
2.2	255
	256
19.2	257	== 2.3 SDI-12 Related Commands ==
2.2	258
	259
90.4	260	User need to configure SDI-12-LB/LS to communicate with SDI-12 sensors otherwise the uplink payload will only include a few bytes.
2.2	261
	262
29.2	263	=== 2.3.1 Basic SDI-12 debug command ===
2.2	264
	265
	266	User can run some basic SDI-12 command to debug the connection to the SDI-12 sensor. These commands can be sent via AT Command or LoRaWAN downlink command.
	267
90.4	268	If SDI-12 sensor return value after get these commands, //SDI-12-LB/LS// will uplink the return on FPORT=100, otherwise, if there is no response from SDI-12 sensor. //SDI-12-LB/LS// will uplink NULL (0x 4E 55 4C 4C) to server.
2.2	269
	270	The following is the display information on the serial port and the server.
	271
	272
47.1	273	[[image:image-20230201091027-6.png\|\|_mstalt="429065"]]
2.2	274
19.2	275
47.1	276	[[image:image-20230201091027-7.png\|\|_mstalt="429429" height="261" width="1179"]]
19.2	277
	278
41.4	279
40.2	280	==== (% style="color:blue" %)al! ~-~- Get SDI-12 sensor Identification(%%) ====
19.2	281
	282
2.2	283	* AT Command: AT+ADDRI=aa
	284	* LoRaWAN Downlink(prefix 0xAA00): AA 00 aa
	285
40.2	286	(% style="color:#037691" %)Parameter: (%%)aa: ASCII value of SDI-12 sensor address in downlink or HEX value in AT Command)
2.2	287
41.4	288	(% style="color:blue" %)Example : (%%)AT+ADDRI=0 ( Equal to downlink: 0x AA 00 30)
2.2	289
	290
	291	The following is the display information on the serial port and the server.
	292
	293
47.1	294	[[image:image-20230201091257-8.png\|\|_mstalt="431392"]]
2.2	295
	296
47.1	297	[[image:image-20230201091257-9.png\|\|_mstalt="431756" height="225" width="1242"]]
19.2	298
	299
40.2	300	==== (% style="color:blue" %)aM!,aMC!, aM1!- aM9!, aMC1!- aMC9!(%%) ====
2.2	301
	302
40.2	303	(% style="color:red" %)aM! (%%): Start Non-Concurrent Measurement
2.2	304
40.2	305	(% style="color:red" %)aMC! (%%): Start Non-Concurrent Measurement – Request CRC
2.2	306
40.2	307	(% style="color:red" %)aM1!- aM9! (%%): Additional Measurements
2.2	308
40.2	309	(% style="color:red" %)aMC1!- aMC9!(%%) : Additional Measurements – Request CRC
2.2	310
27.2	311
2.2	312	* AT Command : AT+ADDRM=0,1,0,1
37.10	313
2.2	314	* LoRaWAN Downlink(prefix 0xAA01): 0xAA 01 30 01 00 01
	315
	316	Downlink：AA 01 aa bb cc dd
	317
40.2	318	(% style="color:#037691" %)aa(%%): SDI-12 sensor address.
2.2	319
40.2	320	(% style="color:#037691" %)bb(%%): 0: no CRC, 1: request CRC
2.2	321
40.2	322	(% style="color:#037691" %)cc(%%): 1-9: Additional Measurement, 0: no additional measurement
2.2	323
41.5	324	(% style="color:#037691" %)dd(%%): delay (in second) to send (% style="color:#037691" %)__aD0!__(%%) to get return.
2.2	325
	326
	327	The following is the display information on the serial port and the server.
	328
	329
47.1	330	[[image:image-20230201091630-10.png\|\|_mstalt="449995"]]
2.2	331
	332
47.1	333	[[image:image-20230201091630-11.png\|\|_mstalt="450372" height="247" width="1165"]]
2.2	334
	335
	336
40.2	337	==== (% style="color:blue" %)aC!, aCC!, aC1!- aC9!, aCC1!- aCC9! (%%) ====
2.2	338
	339
40.2	340	(% style="color:red" %)aC!(%%) : Start Concurrent Measurement
2.2	341
40.2	342	(% style="color:red" %)aCC! (%%): Start Concurrent Measurement – Request CRC
2.2	343
40.2	344	(% style="color:red" %)aC1!- aC9!(%%) : Start Additional Concurrent Measurements
27.2	345
40.2	346	(% style="color:red" %)aCC1!- aCC9!(%%) : Start Additional Concurrent Measurements – Request CRC
27.2	347
	348
2.2	349	* AT Command : AT+ADDRC=0,1,0,1
	350
	351	* LoRaWAN Downlink(0xAA02): 0xAA 02 30 01 00 01
	352
	353	Downlink: AA 02 aa bb cc dd
	354
40.2	355	(% style="color:#037691" %)aa(%%): SDI-12 sensor address.
2.2	356
40.2	357	(% style="color:#037691" %)bb(%%): 0: no CRC, 1: request CRC
2.2	358
40.2	359	(% style="color:#037691" %)cc(%%): 1-9: Additional Measurement, 0: no additional measurement
2.2	360
41.5	361	(% style="color:#037691" %)dd(%%): delay (in second) to send (% style="color:#037691" %)__aD0!__(%%)__ __to get return.
2.2	362
	363
	364	The following is the display information on the serial port and the server.
	365
	366
47.1	367	[[image:image-20230201091954-12.png\|\|_mstalt="453687"]]
2.2	368
	369
47.1	370	[[image:image-20230201091954-13.png\|\|_mstalt="454064" height="203" width="1117"]]
2.2	371
27.2	372
	373
40.2	374	==== (% style="color:blue" %)aR0!- aR9!, aRC0!- aRC9!(%%) ====
27.2	375
37.10	376
2.2	377	Start Continuous Measurement
	378
	379	Start Continuous Measurement – Request CRC
	380
	381
	382	* AT Command : AT+ADDRR=0,1,0,1
	383	* LoRaWAN Downlink (0xAA 03): 0xAA 03 30 01 00 01
	384
	385	Downlink: AA 03 aa bb cc dd
	386
40.2	387	(% style="color:#037691" %)aa(%%): SDI-12 sensor address.
2.2	388
40.2	389	(% style="color:#037691" %)bb(%%): 0: no CRC, 1: request CRC
2.2	390
40.2	391	(% style="color:#037691" %)cc(%%): 1-9: Additional Measurement, 0: no additional measurement
2.2	392
41.5	393	(% style="color:#037691" %)dd(%%): delay (in second) to send (% style="color:#037691" %)__aD0!__(%%) to get return.
2.2	394
	395
	396	The following is the display information on the serial port and the server.
	397
	398
47.1	399	[[image:image-20230201092208-14.png\|\|_mstalt="452283"]]
2.2	400
27.2	401
47.1	402	[[image:image-20230201092208-15.png\|\|_mstalt="452660" height="214" width="1140"]]
27.2	403
	404
37.2	405	=== 2.3.2 Advance SDI-12 Debug command ===
27.2	406
	407
2.2	408	This command can be used to debug all SDI-12 command.
	409
	410
73.1	411	LoRaWAN Downlink: A8 aa xx xx xx xx bb cc dd
2.2	412
40.2	413	(% style="color:#037691" %)aa (%%): total SDI-12 command length
2.2	414
40.2	415	(% style="color:#037691" %)xx (%%): SDI-12 command
2.2	416
40.2	417	(% style="color:#037691" %)bb (%%): Delay to wait for return
2.2	418
40.2	419	(% style="color:#037691" %)cc (%%): 0: don't uplink return to LoRaWAN, 1: Uplink return to LoRaWAN on FPORT=100
2.2	420
73.1	421	(% style="color:#037691" %)dd: (%%) 0: Do not use aD0! command access, 1: use aD0! command access.
2.2	422
	423
73.1	424	(% style="color:blue" %)Example1: (%%) AT+CFGDEV =0RC0!,1
	425
40.2	426	(% style="color:#037691" %)0RC0! (%%): SDI-12 Command,
2.2	427
40.2	428	(% style="color:#037691" %)1 (%%): Delay 1 second. ( 0: 810 mini-second)
2.2	429
	430	Equal Downlink: 0xA8 05 30 52 43 30 21 01 01
	431
	432
	433	The following is the display information on the serial port and the server.
	434
	435
47.1	436	[[image:image-20230201092355-16.png\|\|_mstalt="453960"]]
2.2	437
	438
47.1	439	[[image:image-20230201092355-17.png\|\|_mstalt="454337" height="426" width="1135"]]
27.2	440
29.2	441
87.1	442	(% style="color:blue" %)Example2: (%%) AT+CFGDEV =0M!,1,1
73.1	443
	444	(% style="color:#037691" %)0M! (%%): SDI-12 Command,
	445
	446	(% style="color:#037691" %)1 (%%): Delay 1 second. ( 0: 810 mini-second)
	447
87.3	448	(% style="color:#037691" %)1 (%%): Use aD0! command access.
73.1	449
	450	Equal Downlink: 0xA8 03 30 4D 21 01 01 01
	451
	452
86.1	453	The following is the display information on the serial port and the server.
	454
	455
	456	[[image:image-20230628091055-1.png\|\|height="368" width="462"]]
	457
	458	[[image:image-20230628091130-2.png\|\|height="258" width="879"]]
	459
	460
29.2	461	=== 2.3.3 Convert ASCII to String ===
	462
	463
2.2	464	This command is used to convert between ASCII and String format.
	465
	466	AT+CONVFORM ( Max length: 80 bytes)
	467
	468
40.2	469	(% style="color:blue" %)Example:
2.2	470
29.2	471	1) AT+CONVFORM=0, string Convert String from String to ASCII
2.2	472
47.1	473	[[image:1675214845056-885.png\|\|_mstalt="297622"]]
2.2	474
	475
29.2	476	2) AT+CONVFORM=1, ASCII Convert ASCII to String.
2.2	477
47.1	478	[[image:1675214856590-846.png\|\|_mstalt="297739"]]
2.2	479
29.2	480
	481	=== 2.3.4 Define periodically SDI-12 commands and uplink. ===
	482
	483
2.2	484	AT+COMMANDx & AT+DATACUTx
	485
90.4	486	User can define max 15 SDI-12 Commands (AT+COMMAND1 ~~ AT+COMMANDF). On each uplink period (TDC time, default 20 minutes), SDI-12-LB/LS will send these SDI-12 commands and wait for return from SDI-12 sensors. SDI-12-LB/LS will then combine these returns and uplink via LoRaWAN.
2.2	487
	488
40.2	489	* (% style="color:blue" %)AT Command:
2.2	490
40.2	491	(% style="color:#037691" %)AT+COMMANDx=var1,var2,var3,var4.
2.2	492
40.2	493	(% style="color:red" %)var1(%%): SDI-12 command , for example: 0RC0!
2.2	494
40.2	495	(% style="color:red" %)var2(%%): Wait timeout for return. (unit: second)
2.2	496
40.2	497	(% style="color:red" %)var3(%%): Whether to send //addrD0!// to get return after var2 timeout. 0: Don't Send //addrD0! //; 1: Send //addrD0!//.
2.2	498
90.4	499	(% style="color:red" %)var4(%%): validation check for return. If return invalid, SDI-12-LB/LS will resend this command. Max 3 retries.
2.2	500
40.2	501	(% style="color:red" %)0 (%%) No validation check;
2.2	502
40.2	503	(% style="color:red" %)1 (%%) Check if return chars are printable char(0x20 ~~ 0x7E);
2.2	504
41.5	505	(% style="color:red" %)2(%%) Check if there is return from SDI-12 sensor
2.2	506
40.2	507	(% style="color:red" %)3 (%%) Check if return pass CRC check ( SDI-12 command var1 must include CRC request);
2.2	508
	509
40.2	510	Each AT+COMMANDx is followed by a (% style="color:blue" %)AT+DATACUT(%%) command. AT+DATACUT command is used to take the useful string from the SDI-12 sensor so the final payload will have the minimum length to uplink.
2.2	511
	512
40.2	513	(% style="color:blue" %)AT+DATACUTx(%%) : This command defines how to handle the return from AT+COMMANDx, max return length is 100 bytes.
2.2	514
48.4	515	(% border="1" style="width:436px" %)
48.16	516	\|(% style="background-color:#f2f2f2; width:433px" %)(((
	517	(% style="color:#0070c0" %)AT+DATACUTx=a,b,c
2.2	518
29.2	519	a: length for the return of AT+COMMAND
2.2	520
37.11	521	b: 1: grab valid value by byte, max 6 bytes. 2: grab valid value by bytes section, max 3 sections.
2.2	522
29.2	523	c: define the position for valid value.
2.2	524	)))
	525
43.1	526	For example, if return from AT+COMMAND1 is “013METER TER12 112T12-00024895<CR><LF>” , Below AT+DATACUT1 will get different result to combine payload:
2.2	527
	528
90.13	529	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
90.14	530	\|=(% style="width: 164px;background-color:#4F81BD;color:white" %)AT+DATACUT1 value\|=(% style="width: 346px;background-color:#4F81BD;color:white" %)Final Result to combine Payload
48.16	531	\|(% style="background-color:#f2f2f2; width:164px" %)34,1,1+2+3\|(% style="background-color:#f2f2f2; width:344px" %)0D 00 01 30 31 33
	532	\|(% style="background-color:#f2f2f2; width:164px" %)34,2,1~~8+12~~16\|(% style="background-color:#f2f2f2; width:344px" %)0D 00 01 30 31 33 4D 45 54 45 52 54 45 52 31 32
	533	\|(% style="background-color:#f2f2f2; width:164px" %)34,2,1~~34\|(% style="background-color:#f2f2f2; width:344px" %)0D 00 01 30 31 33 4D 45 54 45 52 20 20 20 54 45 52 31 32 20 31 31 32 54 31 32 2D 30 30 30 32 34 38 39 35 0D 0A
2.2	534
40.2	535	* (% style="color:blue" %) Downlink Payload:
2.2	536
40.2	537	(% style="color:blue" %)0xAF(%%) downlink command can be used to set AT+COMMANDx or AT+DATACUTx.
2.2	538
	539
40.2	540	(% style="color:red" %)Note : if user use AT+COMMANDx to add a new command, he also need to send AT+DATACUTx downlink.
2.2	541
	542
40.2	543	Format: (% style="color:#037691" %)AF MM NN LL XX XX XX XX YY(%%)
2.2	544
	545	Where:
	546
40.2	547	* (% style="color:#037691" %)MM (%%): the AT+COMMAND or AT+DATACUT to be set. Value from 01 ~~ 0F,
43.1	548	* (% style="color:#037691" %)NN (%%): 1: set the AT+COMMAND value ; 2: set the AT+DATACUT value.
40.2	549	* (% style="color:#037691" %)LL (%%): The length of AT+COMMAND or AT+DATACUT command
	550	* (% style="color:#037691" %)XX XX XX XX (%%): AT+COMMAND or AT+DATACUT command
90.4	551	* (% style="color:#037691" %)YY (%%): If YY=0, SDI-12-LB/LS will execute the downlink command without uplink; if YY=1, SDI-12-LB/LS will execute an uplink after got this command.
2.2	552
40.2	553	(% style="color:blue" %)Example:
2.2	554
47.1	555	[[image:image-20230201094129-18.png\|\|_mstalt="455065"]]
2.2	556
	557
41.16	558
40.2	559	(% style="color:blue" %)Clear SDI12 Command
2.2	560
	561	The AT+COMMANDx and AT+DATACUTx settings are stored in special location, user can use below command to clear them.
	562
	563
40.2	564	* (% style="color:#037691" %)AT Command:
2.2	565
40.2	566	(% style="color:#4f81bd" %)AT+CMDEAR=mm,nn (%%) mm: start position of erase ,nn: stop position of erase
2.2	567
	568
	569	Etc. AT+CMDEAR=1,10 means erase AT+COMMAND1/AT+DATACUT1 to AT+COMMAND10/AT+DATACUT10
	570
	571
90.9	572	* (% style="color:#037691" %)Downlink Payload:
2.2	573
40.2	574	(% style="color:#4f81bd" %)0x09 aa bb(%%) same as AT+CMDEAR=aa,bb
2.2	575
	576
	577
40.2	578	(% style="color:blue" %)command combination
2.2	579
	580	Below shows a screen shot how the results combines together to a uplink payload.
	581
47.1	582	[[image:1675215745275-920.png\|\|_mstalt="295334"]]
2.2	583
	584
35.2	585	If user don't want to use DATACUT for some command, he simply want to uplink all returns. AT+ALLDATAMOD can be set to 1.
2.2	586
40.2	587	(% style="color:blue" %)AT+ALLDATAMOD(%%) will simply get all return and don't do CRC check as result for SDI-12 command. AT+DATACUTx command has higher priority, if AT+DATACUTx has been set, AT+ALLDATAMOD will be ignore for this SDI-12 command.
2.2	588
	589
41.7	590	(% style="color:#4f81bd" %)For example: (%%) as below photo, AT+ALLDATAMOD=1, but AT+DATACUT1 has been set, AT+DATACUT1 will be still effect the result.
2.2	591
	592
47.1	593	[[image:1675215782925-448.png\|\|_mstalt="297466"]]
2.2	594
	595
40.2	596	If AT+ALLDATAMOD=1, (% style="color:#4f81bd" %)FX,X(%%) will be added in the payload, FX specify which command is used and X specify the length of return. for example in above screen, F1 05 means the return is from AT+COMMAND1 and the return is 5 bytes.
2.2	597
	598
	599
41.17	600	(% style="color:blue" %)Compose Uplink
2.2	601
40.2	602	(% style="color:#4f81bd" %)AT+DATAUP=0
2.2	603
41.8	604	Compose the uplink payload with value returns in sequence and send with __A SIGNLE UPLINK__.
2.2	605
41.8	606	Final Payload is __Battery Info+PAYVER + VALID Value from RETURN1 + Valid Value from RETURN2 + … + RETURNx__
2.2	607
	608	Where PAYVER is defined by AT+PAYVER, below is an example screen shot.
	609
	610
47.1	611	[[image:1675215828102-844.png\|\|_mstalt="294645"]]
2.2	612
	613
40.2	614	(% style="color:#4f81bd" %)AT+DATAUP=1
2.2	615
41.8	616	Compose the uplink payload with value returns in sequence and send with __Multiply UPLINKs__.
2.2	617
41.8	618	Final Payload is __Battery Info+PAYVER + PAYLOAD COUNT + PAYLOAD# + DATA__
2.2	619
	620	1. Battery Info (2 bytes): Battery voltage
	621	1. PAYVER (1 byte): Defined by AT+PAYVER
	622	1. PAYLOAD COUNT (1 byte): Total how many uplinks of this sampling.
	623	1. PAYLOAD# (1 byte): Number of this uplink. (from 0,1,2,3…,to PAYLOAD COUNT)
	624	1. DATA: Valid value: max 6 bytes(US915 version here, Notice*!) for each uplink so each uplink <= 11 bytes. For the last uplink, DATA will might less than 6 bytes
	625
47.1	626	[[image:1675215848113-696.png\|\|_mstalt="296998"]]
2.2	627
	628
40.2	629	(% style="color:red" %)Notice: the Max bytes is according to the max support bytes in different Frequency Bands for lowest SF. As below:
2.2	630
35.2	631	* For AU915/AS923 bands, if UplinkDwell time=0, max 51 bytes for each uplink ( so 51 -5 = 46 max valid date)
	632	* For AU915/AS923 bands, if UplinkDwell time=1, max 11 bytes for each uplink ( so 11 -5 = 6 max valid date).
	633	* For US915 band, max 11 bytes for each uplink ( so 11 -5 = 6 max valid date).
	634	* For all other bands: max 51 bytes for each uplink ( so 51 -5 = 46 max valid date).
2.2	635
40.2	636	(% style="color:red" %)When AT+DATAUP=1, the maximum number of segments is 15, and the maximum total number of bytes is 1500;
2.2	637
40.2	638	(% style="color:red" %)When AT+DATAUP=1 and AT+ADR=0, the maximum number of bytes of each payload is determined by the DR value.
2.2	639
	640
40.7	641	== 2.4 Uplink Payload ==
2.2	642
37.2	643	=== 2.4.1 Device Payload, FPORT~=5 ===
2.2	644
37.2	645
90.4	646	Include device configure status. Once SDI-12-LB/LS Joined the network, it will uplink this message to the server.
2.2	647
90.4	648	Users can also use the downlink command(0x26 01) to ask SDI-12-LB/LS to resend this uplink.
2.2	649
90.13	650	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
90.10	651	\|(% colspan="6" style="background-color:#4f81bd; color:white" %)Device Status (FPORT=5)
48.5	652	\|(% style="background-color:#f2f2f2; width:103px" %)Size (bytes)\|(% style="background-color:#f2f2f2; width:72px" %)1\|(% style="background-color:#f2f2f2" %)2\|(% style="background-color:#f2f2f2; width:91px" %)1\|(% style="background-color:#f2f2f2; width:86px" %)1\|(% style="background-color:#f2f2f2; width:44px" %)2
	653	\|(% style="background-color:#f2f2f2; width:103px" %)Value\|(% style="background-color:#f2f2f2; width:72px" %)Sensor Model\|(% style="background-color:#f2f2f2" %)Firmware Version\|(% style="background-color:#f2f2f2; width:91px" %)Frequency Band\|(% style="background-color:#f2f2f2; width:86px" %)Sub-band\|(% style="background-color:#f2f2f2; width:44px" %)BAT
2.2	654
	655	Example parse in TTNv3
	656
47.1	657	[[image:1675215946738-635.png\|\|_mstalt="297778"]]
2.2	658
37.2	659
90.4	660	(% style="color:#037691" %)Sensor Model(%%): For SDI-12-LB/LS, this value is 0x17
2.2	661
40.2	662	(% style="color:#037691" %)Firmware Version(%%): 0x0100, Means: v1.0.0 version
2.2	663
40.2	664	(% style="color:#037691" %)Frequency Band:
2.2	665
73.2	666	0x01: EU868
2.2	667
73.2	668	0x02: US915
2.2	669
73.2	670	0x03: IN865
2.2	671
73.2	672	0x04: AU915
2.2	673
73.2	674	0x05: KZ865
2.2	675
73.2	676	0x06: RU864
2.2	677
73.2	678	0x07: AS923
2.2	679
73.2	680	0x08: AS923-1
2.2	681
73.2	682	0x09: AS923-2
2.2	683
73.2	684	0x0a: AS923-3
2.2	685
73.2	686	0x0b: CN470
2.2	687
73.2	688	0x0c: EU433
2.2	689
73.2	690	0x0d: KR920
2.2	691
73.2	692	0x0e: MA869
2.2	693
	694
40.2	695	(% style="color:#037691" %)Sub-Band:
2.2	696
	697	AU915 and US915:value 0x00 ~~ 0x08
	698
	699	CN470: value 0x0B ~~ 0x0C
	700
	701	Other Bands: Always 0x00
	702
	703
40.2	704	(% style="color:#037691" %)Battery Info:
2.2	705
	706	Check the battery voltage.
	707
	708	Ex1: 0x0B45 = 2885mV
	709
	710	Ex2: 0x0B49 = 2889mV
	711
	712
37.2	713	=== 2.4.2 Uplink Payload, FPORT~=2 ===
2.2	714
37.2	715
2.2	716	There are different cases for uplink. See below
	717
	718	* SDI-12 Debug Command return: FPORT=100
	719
	720	* Periodically Uplink: FPORT=2
	721
90.13	722	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:500px" %)
90.7	723	\|=(% style="width: 90px;background-color:#4F81BD;color:white" %)(((
37.2	724	Size(bytes)
90.7	725	)))\|=(% style="width: 80px;background-color:#4F81BD;color:white" %)2\|=(% style="width: 90px;background-color:#4F81BD;color:white" %)1\|=(% style="width: 240px;background-color:#4F81BD;color:white" %)Length depends on the return from the commands
87.9	726	\|(% style="width:93px" %)Value\|(% style="width:83px" %)(((
2.2	727	Battery(mV)
	728	&
	729	Interrupt_Flag
41.18	730	)))\|(% style="width:91px" %)[[PAYLOAD_VER>>\|\|anchor="H3.6Setthepayloadversion"]]\|(% style="width:212px" %)(((
37.2	731	If the valid payload is too long and exceed the maximum support.
2.2	732	Payload length in server,server will show payload not provided in the LoRaWAN server.
	733	)))
	734
47.1	735	[[image:1675216282284-923.png\|\|_mstalt="295633"]]
2.2	736
	737
37.2	738	=== 2.4.3 Battery Info ===
2.2	739
	740
90.4	741	Check the battery voltage for SDI-12-LB/LS.
2.2	742
	743	Ex1: 0x0B45 = 2885mV
	744
	745	Ex2: 0x0B49 = 2889mV
	746
	747
37.2	748	=== 2.4.4 Interrupt Pin ===
2.2	749
37.2	750
40.2	751	This data field shows if this packet is generated by (% style="color:#037691" %)Interrupt Pin(%%) or not. [[Click here>>\|\|anchor="H3.2SetInterruptMode"]] for the hardware and software set up. Note: The Internet Pin is a separate pin in the screw terminal. See [[pin mapping>>\|\|anchor="H1.7PinMapping"]].
2.2	752
37.2	753	Example:
2.2	754
	755	Ex1: 0x0B45:0x0B&0x80= 0x00 Normal uplink packet.
	756
	757	Ex2: 0x8B49:0x8B&0x80= 0x80 Interrupt Uplink Packet.
	758
	759
37.2	760	=== 2.4.5 Payload version ===
2.2	761
49.3	762
43.1	763	The version number of the payload, mainly used for decoding. The default is 01.
2.2	764
	765
37.2	766	=== 2.4.6 Decode payload in The Things Network ===
2.2	767
	768
	769	While using TTN network, you can add the payload format to decode the payload.
	770
47.1	771	[[image:1675216779406-595.png\|\|_mstalt="298376"]]
2.2	772
	773
	774	There is no fix payload decoder in LoRaWAN server because the SDI-12 sensors returns are different. User need to write the decoder themselves for their case.
	775
90.4	776	SDI-12-LB/LS TTN Payload Decoder: [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>url:https://github.com/dragino/dragino-end-node-decoder]]
2.2	777
	778
37.3	779	== 2.5 Uplink Interval ==
2.2	780
	781
90.4	782	The SDI-12-LB/LS by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link:
2.2	783
44.2	784	[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H4.1ChangeUplinkInterval>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H4.1ChangeUplinkInterval]]
2.2	785
	786
56.1	787	== 2.6 Examples To Set SDI commands ==
2.2	788
56.1	789	=== 2.6.1 Examples 1 ~-~- General Example ===
2.2	790
44.2	791
90.4	792	COM port and SDI-12 sensor communication converted to SDI-12-LB/LS and SDI-12 sensor communication.
43.1	793
47.1	794	[[image:image-20230222143809-1.png\|\|_mstalt="429962" height="564" width="729"]]
43.1	795
	796
44.2	797	(% style="color:blue" %)1) The AT+COMMANDx command is applied to the red arrow part, and sends the SDI12 command to the SDI12 sensor:
43.1	798
44.2	799	a. Send the first command and get the first reply：
43.1	800
44.2	801	(% style="color:#037691" %)AT+COMMANDx=1I!,0,0,1
43.1	802
44.2	803	b. Send the second command and get the second reply：
43.1	804
44.2	805	(% style="color:#037691" %)AT+COMMANDx=2I!,0,0,1
43.1	806
44.2	807	c. Send the third command and get the third reply：
43.1	808
44.2	809	(% style="color:#037691" %)AT+COMMANDx=3I!,0,0,1
43.1	810
44.2	811	d. Send the fourth command and get the fourth reply：
43.1	812
44.2	813	(% style="color:#037691" %)AT+COMMANDx=4I!,0,0,1
43.1	814
44.2	815	e. Send the fifth command plus the sixth command, get the sixth reply：
43.1	816
44.2	817	(% style="color:#037691" %)AT+COMMANDx=1M!,2,1,1
43.1	818
44.2	819	f. Send the seventh command plus the eighth command, get the eighth reply：
43.1	820
44.2	821	(% style="color:#037691" %)AT+COMMANDx=2M!,2,1,1
43.1	822
44.2	823	g. Send the ninth command plus the tenth command, get the tenth reply：
43.1	824
44.2	825	(% style="color:#037691" %)AT+COMMANDx=3M!,1,1,1
43.1	826
44.2	827	h. Send the eleventh command plus the twelfth command, get the twelfth reply：
43.1	828
44.2	829	(% style="color:#037691" %)AT+COMMANDx=4M!,1,1,1
43.1	830
	831
90.15	832	(% style="color:blue" %)2) The AT+DATACUTx command is applied to the green arrow part, receiving and cut out data from the SDI12 sensor:
43.1	833
44.2	834	a. The first reply, all 34 characters: ”113TRUEBNERSMT100038220303182331<CR><LF>”
43.1	835
47.1	836	Cut out all characters: (% _mstmutation="1" style="color:#037691" %)AT+ALLDATAMOD=1 or AT+DATACUTx=34,2,1~~34(% style="color:#037691" %);
44.2	837
90.15	838	b. The sixth reply, all 31 characters: "1+19210+1.04+0.00+22.49+11.75<CR><LF>"
43.1	839
47.1	840	Cut out all characters: (% _mstmutation="1" style="color:#037691" %)AT+ALLDATAMOD=1 or AT+DATACUTx=31,2,1~~31(% style="color:#037691" %);
43.1	841
90.15	842	c. The eighth reply, all 31 characters: "2+18990+1.08+0.00+22.24+11.80<CR><LF>"
43.1	843
47.1	844	Cut out all characters: (% _mstmutation="1" style="color:#037691" %)AT+ALLDATAMOD=1 or AT+DATACUTx=31,2,1~~31(% style="color:#037691" %);
43.1	845
90.15	846	d. The tenth reply, all 15 characters: "3-2919.8+24.0<CR><LF>"
43.1	847
47.1	848	Cut out all characters: (% _mstmutation="1" style="color:#037691" %)AT+ALLDATAMOD=1 or AT+DATACUTx=15,2,1~~15(% style="color:#037691" %);
43.1	849
90.15	850	e. The twelfth reply, all 25 characters: "4+30.8+22.84+4.7+954.38<CR><LF>"
43.1	851
90.15	852	Partial cut, the cut sensor address and the first two parameters:(% style="color:#037691" %)AT+DATACUTx=25,2,1~~12, cut out the character field "4+30.8+22.84".
43.1	853
	854
71.1	855	=== 2.6.2 Example 2 ~-~- Connect to Hygrovue10 ===
56.1	856
	857	==== 2.6.2.1 Reference Manual and Command ====
	858
72.2	859
56.1	860	* [[Hygrovue10 Product Page>>https://www.campbellsci.com/hygrovue10]]
72.2	861
56.1	862	* Commands to be used in PC and output.
	863
72.2	864	~1. check device address
56.1	865
72.2	866	2. change device address
56.1	867
72.2	868	3. check device ID
56.1	869
72.2	870	4. start measure
56.1	871
72.2	872	5. Get Meausre result
56.1	873
	874	[[image:image-20230603120209-2.png\|\|height="281" width="267"]]
	875
	876
90.4	877	==== 2.6.2.2 Hardware Connection to SDI-12-LB/LS ====
56.1	878
72.2	879
56.1	880	[[image:image-20230603120515-3.png]]
	881
	882
90.4	883	==== 2.6.2.3 Commands set in SDI-12-LB/LS and uplink payload ====
56.1	884
72.2	885
56.1	886	[[image:image-20230603120648-4.png]]
	887
	888	[[image:image-20230603120726-5.png]]
	889
	890
72.2	891	Data in TTN:
	892
56.1	893	[[image:image-20230603120859-6.png\|\|height="118" width="1285"]]
	894
	895
87.5	896	=== 2.6.3 Example 3 ~-~- Connect to SIL-400 ===
56.1	897
71.1	898	==== 2.6.3.1 Reference Manual and Command ====
56.1	899
72.2	900
71.1	901	* [[SIL-400 Product Page>>https://www.apogeeinstruments.com/sil-411-commercial-grade-sdi-12-digital-output-standard-field-of-view-infrared-radiometer-sensor/]]
72.2	902
71.1	903	* Commands to be used in PC and output.
	904
72.2	905	~1. check device address
71.1	906
72.2	907	2. change device address
71.1	908
72.2	909	3. check device ID
71.1	910
72.2	911	4. start measure
71.1	912
72.2	913	5. Get Meausre result
71.1	914
	915	[[image:image-20230603121606-7.png\|\|height="242" width="307"]]
	916
	917
90.4	918	==== 2.6.3.2 Hardware Connection to SDI-12-LB/LS ====
71.1	919
72.3	920
71.1	921	[[image:image-20230603121643-8.png\|\|height="442" width="656"]]
	922
	923
90.4	924	==== 2.6.3.3 Commands set in SDI-12-LB/LS and uplink payload ====
71.1	925
72.3	926
71.1	927	[[image:image-20230603121721-9.png]]
	928
83.1	929	[[image:image-20230628090323-1.png\|\|height="414" width="694"]]
71.1	930
	931	Data in TTN:
	932
	933	[[image:image-20230603121826-11.png\|\|height="155" width="1104"]]
	934
	935
	936
87.4	937	=== 2.6.4 Example 4 ~-~- Connect to TEROS-12 ===
71.1	938
	939	==== 2.6.4.1 Reference Manual and Command ====
	940
72.3	941
71.1	942	* [[TEROS-12 Product Page>>https://www.metergroup.com/en/meter-environment/products/teros-12-soil-moisture-sensor]]
72.3	943
71.1	944	* Commands to be used in PC and output.
	945
	946	1.check device address
	947
	948	2.change device address
	949
	950	3.check device ID
	951
	952	4.start measure
	953
	954	5.Get Meausre result
	955
	956	[[image:image-20230603122248-16.png\|\|height="196" width="198"]]
	957
	958
90.4	959	==== 2.6.4.2 Hardware Connection to SDI-12-LB/LS ====
71.1	960
72.3	961
71.1	962	[[image:image-20230603122212-15.png\|\|height="502" width="667"]]
	963
	964
90.4	965	==== 2.6.4.3 Commands set in SDI-12-LB/LS and uplink payload ====
71.1	966
73.4	967
71.1	968	[[image:image-20230603122040-12.png]]
	969
	970	[[image:image-20230603122109-13.png\|\|height="469" width="762"]]
	971
	972
72.3	973	Data in TTN:
	974
71.1	975	[[image:image-20230603122139-14.png\|\|height="148" width="1128"]]
	976
	977
87.4	978	=== 2.6.5 Example 5 ~-~- Connect to SIL-400/TEROS-12 & Hygrovue10 ===
71.1	979
72.1	980	==== 2.6.5.1 Important Notice! ====
71.1	981
72.3	982
71.1	983	* The product page and reference command see above example 2,3,4
72.3	984
71.1	985	* All of these SDI-12 sensors use the same address (address 0) by default. So we need to change their address to different address, by using aAb! command. See above example.
72.3	986
71.1	987	* The sensor needs to be powered to a steady statue. So the 12VT time need to be set to the maximum stable time for the sensors. in this example, it is 13 seconds.
72.3	988
90.4	989	* If these SDI-12 sensors are powered by external power source. It will add 300uA in the total current in SDI-12-LB/LS.
71.1	990
90.4	991	==== 2.6.5.2 Hardware Connection to SDI-12-LB/LS ====
71.1	992
72.3	993
71.1	994	[[image:image-20230603122508-17.png\|\|height="526" width="742"]]
	995
	996
90.4	997	==== 2.6.5.3 Commands set in SDI-12-LB/LS and uplink payload ====
71.1	998
72.3	999
71.1	1000	[[image:image-20230603122549-18.png]]
	1001
	1002	[[image:image-20230603122623-19.png\|\|height="483" width="1121"]]
	1003
	1004
72.3	1005	Data in TTN:
	1006
71.1	1007	[[image:image-20230603122719-20.png\|\|height="151" width="1179"]]
	1008
	1009
87.4	1010	=== 2.6.6 Example 6 ~-~- Connect to ENTELECHY-EP_SDI-12 ===
81.1	1011
87.4	1012	==== 2.6.6.1 Reference Manual and Command ====
81.1	1013
	1014
	1015	* [[https:~~/~~/enviroprosoilprobes.com/wp-content/uploads/2019/11/ENTELECHY-EP_SDI-12-Commands.pdf>>url:https://enviroprosoilprobes.com/wp-content/uploads/2019/11/ENTELECHY-EP_SDI-12-Commands.pdf]]
	1016
	1017	* Commands to be used in PC and output.
	1018
	1019	1.check device address
	1020
	1021	2.change device address
	1022
	1023	3.check device ID
	1024
	1025	4.start measure
	1026
	1027	5.Get Meausre result
	1028
	1029
	1030	[[image:image-20230627174559-3.png]]
	1031
87.3	1032
90.4	1033	==== 2.6.6.2 Hardware Connection to SDI-12-LB/LS ====
81.1	1034
87.3	1035
81.1	1036	[[image:image-20230627174446-2.png]]
	1037
	1038
	1039
90.4	1040	==== 2.6.6.3 Commands set in SDI-12-LB/LS and uplink payload ====
81.1	1041
	1042
	1043	[[image:image-20230627175513-4.png\|\|height="596" width="576"]]
	1044
	1045	[[image:image-20230627175736-5.png\|\|height="429" width="693"]]
	1046
	1047
	1048	Data in TTN:
	1049
	1050	[[image:image-20230627180303-6.png\|\|height="292" width="1171"]]
	1051
87.3	1052
99.1	1053	=== 2.6.7 Example 6 ~-~- Connect to GroPoint Profile-8 (SDI-12 Version) ===
97.1	1054
99.1	1055	==== 2.6.7.1 Reference Manual and Command ====
97.1	1056
	1057	* [[https:~~/~~/static1.squarespace.com/static/5db0b690c4990258f8f6d042/t/64189e1ab3ebc54e6947b0c0/1679334941034/2625-N-T+GroPoint+Profile+User+Manual-V1.1.3.pdf>>https://static1.squarespace.com/static/5db0b690c4990258f8f6d042/t/64189e1ab3ebc54e6947b0c0/1679334941034/2625-N-T+GroPoint+Profile+User+Manual-V1.1.3.pdf]]
	1058
	1059	* Commands to be used in PC and output.
	1060
99.1	1061	1. check device address
	1062	1. change device address
	1063	1. check device ID
	1064	1. start measure
	1065	1. Get Meausre result
97.1	1066
	1067	[[image:image-20240423143921-1.png]]
	1068
	1069
	1070	==== 2.6.7.2 Hardware Connection to SDI-12-LB/LS ====
	1071
100.1	1072	Note: When the bytes returned by the sensor are not fixed, the full byte interception can be used: AT+ALLDATAMOD=1 (The DATACUTx parameter needs to be cleared when using this directive, or it will not work.)
	1073
97.1	1074	[[image:image-20240423145522-2.png\|\|height="345" width="400"]]
	1075
	1076
	1077	==== 2.6.7.3 Commands set in SDI-12-LB/LS and uplink payload ====
	1078
	1079	[[image:image-20240423151202-3.png]]
	1080
98.1	1081	(% class="wikigeneratedid" id="H" %)
	1082	[[image:image-20240423162851-6.png\|\|height="251" width="935"]]
97.1	1083
	1084
	1085	DATA in TTN:
	1086
98.1	1087	[[image:image-20240423162322-4.png\|\|height="269" width="933"]]
97.1	1088
	1089
43.1	1090	== 2.7 Frequency Plans ==
	1091
	1092
90.11	1093	The SDI-12-LB/LS uses OTAA mode and below frequency plans by default. Each frequency band use different firmware, user update the firmware to the corresponding band for their country.
2.2	1094
37.3	1095	[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]
2.2	1096
	1097
43.1	1098	== 2.8 Firmware Change Log ==
37.3	1099
	1100
2.2	1101	Firmware download link:
	1102
41.9	1103	[[https:~~/~~/www.dropbox.com/sh/qrbgbikb109lkiv/AACBR-v_ZhZAMengcY7Nsa1ja?dl=0>>https://www.dropbox.com/sh/qrbgbikb109lkiv/AACBR-v_ZhZAMengcY7Nsa1ja?dl=0]]
2.2	1104
	1105
90.4	1106	= 3. Configure SDI-12-LB/LS via AT Command or LoRaWAN Downlink =
2.2	1107
	1108
90.4	1109	Use can configure SDI-12-LB/LS via AT Command or LoRaWAN Downlink.
2.2	1110
40.8	1111	* AT Command Connection: See [[FAQ>>\|\|anchor="H7.FAQ"]].
37.3	1112	* LoRaWAN Downlink instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
2.2	1113
90.4	1114	There are two kinds of commands to configure SDI-12-LB/LS, they are:
2.2	1115
40.7	1116	* (% style="color:blue" %)General Commands.
2.2	1117
	1118	These commands are to configure:
	1119
	1120	* General system settings like: uplink interval.
	1121	* LoRaWAN protocol & radio related command.
	1122
	1123	They are same for all Dragino Device which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:
	1124
40.2	1125	[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
2.2	1126
	1127
90.4	1128	* (% style="color:blue" %)Commands special design for SDI-12-LB/LS
2.2	1129
90.4	1130	These commands only valid for SDI-12-LB/LS, as below:
2.2	1131
	1132
43.1	1133	== 3.1 Set Transmit Interval Time ==
2.2	1134
	1135
	1136	Feature: Change LoRaWAN End Node Transmit Interval.
	1137
37.3	1138	(% style="color:blue" %)AT Command: AT+TDC
2.2	1139
90.13	1140	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
90.7	1141	\|=(% style="width: 160px; background-color:#4F81BD;color:white" %)Command Example\|=(% style="width: 160px; background-color:#4F81BD;color:white" %)Function\|=(% style="width: 190px;background-color:#4F81BD;color:white" %)Response
48.7	1142	\|(% style="background-color:#f2f2f2; width:157px" %)AT+TDC=?\|(% style="background-color:#f2f2f2; width:166px" %)Show current transmit Interval\|(% style="background-color:#f2f2f2" %)(((
2.2	1143	30000
	1144	OK
	1145	the interval is 30000ms = 30s
	1146	)))
48.7	1147	\|(% style="background-color:#f2f2f2; width:157px" %)AT+TDC=60000\|(% style="background-color:#f2f2f2; width:166px" %)Set Transmit Interval\|(% style="background-color:#f2f2f2" %)(((
2.2	1148	OK
	1149	Set transmit interval to 60000ms = 60 seconds
	1150	)))
	1151
37.3	1152	(% style="color:blue" %)Downlink Command: 0x01
2.2	1153
	1154	Format: Command Code (0x01) followed by 3 bytes time value.
	1155
37.6	1156	If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
2.2	1157
37.6	1158	* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
	1159	* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
2.2	1160
37.3	1161	== 3.2 Set Interrupt Mode ==
2.2	1162
37.6	1163
2.2	1164	Feature, Set Interrupt mode for GPIO_EXIT.
	1165
37.3	1166	(% style="color:blue" %)AT Command: AT+INTMOD
2.2	1167
90.13	1168	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
90.7	1169	\|=(% style="width: 154px;background-color:#4F81BD;color:white" %)Command Example\|=(% style="width: 196px;background-color:#4F81BD;color:white" %)Function\|=(% style="width: 160px;background-color:#4F81BD;color:white" %)Response
48.8	1170	\|(% style="background-color:#f2f2f2; width:154px" %)AT+INTMOD=?\|(% style="background-color:#f2f2f2; width:196px" %)Show current interrupt mode\|(% style="background-color:#f2f2f2; width:157px" %)(((
2.2	1171	0
	1172	OK
48.8	1173	the mode is 0 =Disable Interrupt
2.2	1174	)))
48.8	1175	\|(% style="background-color:#f2f2f2; width:154px" %)AT+INTMOD=2\|(% style="background-color:#f2f2f2; width:196px" %)(((
2.2	1176	Set Transmit Interval
43.1	1177	0. (Disable Interrupt),
	1178	~1. (Trigger by rising and falling edge)
	1179	2. (Trigger by falling edge)
	1180	3. (Trigger by rising edge)
48.8	1181	)))\|(% style="background-color:#f2f2f2; width:157px" %)OK
2.2	1182
37.3	1183	(% style="color:blue" %)Downlink Command: 0x06
2.2	1184
	1185	Format: Command Code (0x06) followed by 3 bytes.
	1186
	1187	This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
	1188
37.6	1189	* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
	1190	* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
2.2	1191
37.3	1192	== 3.3 Set the output time ==
	1193
	1194
2.2	1195	Feature, Control the output 3V3 , 5V or 12V.
	1196
37.3	1197	(% style="color:blue" %)AT Command: AT+3V3T
2.2	1198
90.13	1199	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:474px" %)
90.7	1200	\|=(% style="width: 154px;background-color:#4F81BD;color:white" %)Command Example\|=(% style="width: 201px;background-color:#4F81BD;color:white" %)Function\|=(% style="width: 120px;background-color:#4F81BD;color:white" %)Response
48.9	1201	\|(% style="background-color:#f2f2f2; width:154px" %)AT+3V3T=?\|(% style="background-color:#f2f2f2; width:201px" %)Show 3V3 open time.\|(% style="background-color:#f2f2f2; width:116px" %)(((
2.2	1202	0
	1203	OK
	1204	)))
48.9	1205	\|(% style="background-color:#f2f2f2; width:154px" %)AT+3V3T=0\|(% style="background-color:#f2f2f2; width:201px" %)Normally open 3V3 power supply.\|(% style="background-color:#f2f2f2; width:116px" %)(((
2.2	1206	OK
	1207	default setting
	1208	)))
48.9	1209	\|(% style="background-color:#f2f2f2; width:154px" %)AT+3V3T=1000\|(% style="background-color:#f2f2f2; width:201px" %)Close after a delay of 1000 milliseconds.\|(% style="background-color:#f2f2f2; width:116px" %)(((
2.2	1210	OK
	1211	)))
48.9	1212	\|(% style="background-color:#f2f2f2; width:154px" %)AT+3V3T=65535\|(% style="background-color:#f2f2f2; width:201px" %)Normally closed 3V3 power supply.\|(% style="background-color:#f2f2f2; width:116px" %)(((
2.2	1213	OK
	1214	)))
	1215
37.3	1216	(% style="color:blue" %)AT Command: AT+5VT
2.2	1217
48.21	1218	(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:470px" %)
90.7	1219	\|=(% style="width: 155px;background-color:#4F81BD;color:white" %)Command Example\|=(% style="width: 196px;background-color:#4F81BD;color:white" %)Function\|=(% style="width: 119px;background-color:#4F81BD;color:white" %)Response
48.9	1220	\|(% style="background-color:#f2f2f2; width:155px" %)AT+5VT=?\|(% style="background-color:#f2f2f2; width:196px" %)Show 5V open time.\|(% style="background-color:#f2f2f2; width:114px" %)(((
2.2	1221	0
	1222	OK
	1223	)))
48.9	1224	\|(% style="background-color:#f2f2f2; width:155px" %)AT+5VT=0\|(% style="background-color:#f2f2f2; width:196px" %)Normally closed 5V power supply.\|(% style="background-color:#f2f2f2; width:114px" %)(((
2.2	1225	OK
	1226	default setting
	1227	)))
48.9	1228	\|(% style="background-color:#f2f2f2; width:155px" %)AT+5VT=1000\|(% style="background-color:#f2f2f2; width:196px" %)Close after a delay of 1000 milliseconds.\|(% style="background-color:#f2f2f2; width:114px" %)(((
2.2	1229	OK
	1230	)))
48.9	1231	\|(% style="background-color:#f2f2f2; width:155px" %)AT+5VT=65535\|(% style="background-color:#f2f2f2; width:196px" %)Normally open 5V power supply.\|(% style="background-color:#f2f2f2; width:114px" %)(((
2.2	1232	OK
	1233	)))
	1234
73.1	1235	(% style="color:blue" %)AT Command: AT+12VT
2.2	1236
87.10	1237	(% style="color:blue" %)(The v1.2 version is enabled for 1 second by default, and the version below v1.2 is disabled by default)
73.1	1238
48.21	1239	(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:443px" %)
90.7	1240	\|=(% style="width: 156px;background-color:#4F81BD;color:white" %)Command Example\|=(% style="width: 199px;background-color:#4F81BD;color:white" %)Function\|=(% style="width: 89px;background-color:#4F81BD;color:white" %)Response
48.9	1241	\|(% style="background-color:#f2f2f2; width:156px" %)AT+12VT=?\|(% style="background-color:#f2f2f2; width:199px" %)Show 12V open time.\|(% style="background-color:#f2f2f2; width:83px" %)(((
2.2	1242	0
	1243	OK
	1244	)))
48.9	1245	\|(% style="background-color:#f2f2f2; width:156px" %)AT+12VT=0\|(% style="background-color:#f2f2f2; width:199px" %)Normally closed 12V power supply.\|(% style="background-color:#f2f2f2; width:83px" %)OK
	1246	\|(% style="background-color:#f2f2f2; width:156px" %)AT+12VT=500\|(% style="background-color:#f2f2f2; width:199px" %)Close after a delay of 500 milliseconds.\|(% style="background-color:#f2f2f2; width:83px" %)(((
2.2	1247	OK
	1248	)))
	1249
37.3	1250	(% style="color:blue" %)Downlink Command: 0x07
2.2	1251
	1252	Format: Command Code (0x07) followed by 3 bytes.
	1253
	1254	The first byte is which power, the second and third bytes are the time to turn on.
	1255
37.3	1256	* Example 1: Downlink Payload: 070101F4 ~-~--> AT+3V3T=500
	1257	* Example 2: Downlink Payload: 0701FFFF ~-~--> AT+3V3T=65535
	1258	* Example 3: Downlink Payload: 070203E8 ~-~--> AT+5VT=1000
	1259	* Example 4: Downlink Payload: 07020000 ~-~--> AT+5VT=0
	1260	* Example 5: Downlink Payload: 070301F4 ~-~--> AT+12VT=500
	1261	* Example 6: Downlink Payload: 07030000 ~-~--> AT+12VT=0
2.2	1262
37.3	1263	== 3.4 Set the all data mode ==
	1264
37.5	1265
2.2	1266	Feature, Set the all data mode.
	1267
37.5	1268	(% style="color:blue" %)AT Command: AT+ALLDATAMOD
2.2	1269
90.13	1270	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:437px" %)
90.7	1271	\|=(% style="background-color:#4F81BD;color:white" %)Command Example\|=(% style="background-color:#4F81BD;color:white" %)Function\|=(% style="background-color:#4F81BD;color:white" %)Response
48.16	1272	\|(% style="background-color:#f2f2f2" %)AT+ALLDATAMOD=?\|(% style="background-color:#f2f2f2" %)Show current all data mode\|(% style="background-color:#f2f2f2" %)(((
2.2	1273	0
	1274	OK
	1275	)))
48.16	1276	\|(% style="background-color:#f2f2f2" %)AT+ALLDATAMOD=1\|(% style="background-color:#f2f2f2" %)Set all data mode is 1.\|(% style="background-color:#f2f2f2" %)OK
2.2	1277
37.5	1278	(% style="color:blue" %)Downlink Command: 0xAB
2.2	1279
	1280	Format: Command Code (0xAB) followed by 1 bytes.
	1281
37.5	1282	* Example 1: Downlink Payload: AB 00 ~/~/ AT+ALLDATAMOD=0
	1283	* Example 2: Downlink Payload: AB 01 ~/~/ AT+ALLDATAMOD=1
2.2	1284
37.3	1285	== 3.5 Set the splicing payload for uplink ==
	1286
37.5	1287
2.2	1288	Feature, splicing payload for uplink.
	1289
37.5	1290	(% style="color:blue" %)AT Command: AT+DATAUP
2.2	1291
90.13	1292	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:510px" %)
90.7	1293	\|=(% style="width: 154px;background-color:#4F81BD;color:white" %)Command Example\|=(% style="width: 266px;background-color:#4F81BD;color:white" %)Function\|=(% style="background-color:#4F81BD;color:white" %)Response
48.16	1294	\|(% style="background-color:#f2f2f2; width:154px" %)AT+DATAUP =?\|(% style="background-color:#f2f2f2; width:266px" %)Show current splicing payload for uplink mode\|(% style="background-color:#f2f2f2" %)(((
2.2	1295	0
	1296	OK
	1297	)))
48.16	1298	\|(% style="background-color:#f2f2f2; width:154px" %)AT+DATAUP =0\|(% style="background-color:#f2f2f2; width:266px" %)(((
2.2	1299	Set splicing payload for uplink mode is 0.
48.16	1300	)))\|(% style="background-color:#f2f2f2" %)(((
2.2	1301	OK
	1302	)))
48.16	1303	\|(% style="background-color:#f2f2f2; width:154px" %)AT+DATAUP =1\|(% style="background-color:#f2f2f2; width:266px" %)Set splicing payload for uplink mode is 1 , and the each splice uplink is sent sequentially.\|(% style="background-color:#f2f2f2" %)OK
	1304	\|(% style="background-color:#f2f2f2; width:154px" %)AT+DATAUP =1,20000\|(% style="background-color:#f2f2f2; width:266px" %)(((
37.3	1305	Set splicing payload for uplink mode is 1, and the uplink interval of each splice to 20000 milliseconds.
48.16	1306	)))\|(% style="background-color:#f2f2f2" %)OK
2.2	1307
37.5	1308	(% style="color:blue" %)Downlink Command: 0xAD
2.2	1309
	1310	Format: Command Code (0xAD) followed by 1 bytes or 5 bytes.
	1311
37.6	1312	* Example 1: Downlink Payload: AD 00 ~/~/ AT+DATAUP=0
	1313	* Example 2: Downlink Payload: AD 01 ~/~/ AT+DATAUP =1
	1314	* Example 3: Downlink Payload: AD 01 00 00 14 ~/~/ AT+DATAUP =1,20000
2.2	1315
	1316	This means that the interval is set to 0x000014=20S
	1317
	1318
37.3	1319	== 3.6 Set the payload version ==
2.2	1320
41.20	1321
2.2	1322	Feature, Set the payload version.
	1323
37.5	1324	(% style="color:blue" %)AT Command: AT+PAYVER
2.2	1325
90.13	1326	(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:437px" %)
90.7	1327	\|=(% style="width: 158px;background-color:#4F81BD;color:white" %)Command Example\|=(% style="width: 192px;background-color:#4F81BD;color:white" %)Function\|=(% style="background-color:#4F81BD;color:white" %)Response
48.16	1328	\|(% style="background-color:#f2f2f2; width:158px" %)AT+PAYVER=?\|(% style="background-color:#f2f2f2; width:192px" %)Show current payload version\|(% style="background-color:#f2f2f2" %)(((
2.2	1329	1
	1330	OK
	1331	)))
48.16	1332	\|(% style="background-color:#f2f2f2; width:158px" %)AT+PAYVER=5\|(% style="background-color:#f2f2f2; width:192px" %)Set payload version is 5.\|(% style="background-color:#f2f2f2" %)OK
2.2	1333
37.5	1334	(% style="color:blue" %)Downlink Command: 0xAE
2.2	1335
	1336	Format: Command Code (0xAE) followed by 1 bytes.
	1337
37.6	1338	* Example 1: Downlink Payload: AE 01 ~/~/ AT+PAYVER=1
	1339	* Example 2: Downlink Payload: AE 05 ~/~/ AT+PAYVER=5
2.2	1340
48.14	1341	= 4. Battery & Power Consumption =
2.2	1342
48.16	1343
90.4	1344	SDI-12-LB use ER26500 + SPC1520 battery pack and SDI-12-LS use 3000mAh Recharable Battery with Solar Panel. See below link for detail information about the battery info and how to replace.
2.2	1345
48.16	1346	[[Battery Info & Power Consumption Analyze>>url:http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
37.3	1347
	1348
	1349	= 5. Remote Configure device =
2.2	1350
37.3	1351	== 5.1 Connect via BLE ==
2.2	1352
	1353
37.3	1354	Please see this instruction for how to configure via BLE: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]]
2.2	1355
	1356
37.3	1357	== 5.2 AT Command Set ==
2.2	1358
	1359
	1360
37.3	1361	= 6. OTA firmware update =
	1362
	1363
2.2	1364	Please see this link for how to do OTA firmware update.
	1365
	1366	[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]
	1367
	1368
40.2	1369	= 7. FAQ =
2.2	1370
48.1	1371	== 7.1 How to use AT Command via UART to access device? ==
2.2	1372
	1373
40.2	1374	See: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]
	1375
	1376
	1377	== 7.2 How to update firmware via UART port? ==
	1378
	1379
	1380	See: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]
	1381
	1382
	1383	== 7.3 How to change the LoRa Frequency Bands/Region? ==
	1384
	1385
	1386	You can follow the instructions for [[how to upgrade image>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome]].
	1387	When downloading the images, choose the required image file for download.
	1388
	1389
	1390	= 8. Order Info =
	1391
	1392
41.20	1393	(((
90.10	1394	Part Number: (% style="color:blue" %)SDI-12-LB-XX-YY(%%) or (% style="color:blue" %)SDI-12-LS-XX-YY(%%)
41.20	1395	)))
40.7	1396
41.20	1397	(((
87.6	1398	(% style="color:blue" %)XX(%%): The default frequency band
41.20	1399	)))
2.2	1400
41.20	1401	(((
87.6	1402	* (% style="color:red" %)AS923(%%): LoRaWAN AS923 band
	1403	* (% style="color:red" %)AU915(%%): LoRaWAN AU915 band
	1404	* (% style="color:red" %)EU433(%%): LoRaWAN EU433 band
	1405	* (% style="color:red" %)EU868(%%): LoRaWAN EU868 band
	1406	* (% style="color:red" %)KR920(%%): LoRaWAN KR920 band
	1407	* (% style="color:red" %)US915(%%): LoRaWAN US915 band
	1408	* (% style="color:red" %)IN865(%%): LoRaWAN IN865 band
	1409	* (% style="color:red" %)CN470(%%): LoRaWAN CN470 band
41.20	1410	)))
2.2	1411
87.6	1412	(% style="color:blue" %)YY: (%%)The grand connector hole size
2.2	1413
87.6	1414	* M12: M12 hole
	1415	* M16: M16 hole
	1416
40.2	1417	= 9. Packing Info =
37.3	1418
	1419
40.7	1420	(% style="color:#037691" %)Package Includes:
2.2	1421
90.4	1422	* SDI-12-LB or SDI-12-LS SDI-12 to LoRaWAN Converter x 1
2.2	1423
40.7	1424	(% style="color:#037691" %)Dimension and weight:
2.2	1425
	1426	* Device Size: cm
	1427	* Device Weight: g
	1428	* Package Size / pcs : cm
	1429	* Weight / pcs : g
	1430
40.2	1431	= 10. Support =
37.3	1432
	1433
2.2	1434	* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
	1435
37.3	1436	* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]

Wiki source code of SDI-12-LB/LS -- SDI-12 to LoRaWAN Converter User Manual

Applications

Navigation