Skip to Content
Last modified by Mengting Qiu on 2025/07/01 15:58
From version 76.8
edited by Xiaoling
on 2024/01/04 18:34
Change comment: There is no comment for this version
To version 73.3
edited by Xiaoling
on 2024/01/04 16:30
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -9,7 +9,7 @@
9 9  
10 10  
11 11  
12 -**Table of Contents:**
12 +**Table of Contents：**
13 13  
14 14  {{toc/}}
15 15  
... ... @@ -51,8 +51,7 @@
51 51  * Support wireless OTA update firmware
52 52  * Uplink on periodically
53 53  * Downlink to change configure
54 -* 88500mAh Li/SOCl2 Battery (S31/S31B-LB)
55 -* Solar panel + 3000mAh Li-on battery (S31/S31B-LS)
54 +* 8500mAh Battery for long term use
56 56  
57 57  == 1.3 Specification ==
58 58  
... ... @@ -59,7 +59,7 @@
59 59  
60 60  (% style="color:#037691" %)**Common DC Characteristics:**
61 61  
62 -* Supply Voltage: Built-in Battery , 2.5v ~~ 3.6v
61 +* Supply Voltage: built in 8500mAh Li-SOCI2 battery , 2.5v ~~ 3.6v
63 63  * Operating Temperature: -40 ~~ 85°C
64 64  
65 65  (% style="color:#037691" %)**Temperature Sensor:**
... ... @@ -107,10 +107,11 @@
107 107  == 1.5 Button & LEDs ==
108 108  
109 109  
110 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/RS485-LB_Waterproof_RS485UART_to_LoRaWAN_Converter/WebHome/image-20240103160425-4.png?rev=1.1||alt="image-20240103160425-4.png"]]
109 +[[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675071855856-879.png]]
111 111  
111 +
112 112  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
113 -|=(% style="width: 167px;background-color:#4F81BD;color:white" %)**Behavior on ACT**|=(% style="width: 117px;background-color:#4F81BD;color:white" %)**Function**|=(% style="width: 225px;background-color:#4F81BD;color:white" %)**Action**
113 +|=(% style="width: 167px;background-color:#D9E2F3;color:#0070C0" %)**Behavior on ACT**|=(% style="width: 117px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 225px;background-color:#D9E2F3;color:#0070C0" %)**Action**
114 114  |(% style="width:167px" %)Pressing ACT between 1s < time < 3s|(% style="width:117px" %)Send an uplink|(% style="width:225px" %)(((
115 115  If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, (% style="color:blue" %)**blue led** (%%)will blink once.
116 116  Meanwhile, BLE module will be active and user can connect via BLE to configure device.
... ... @@ -125,7 +125,7 @@
125 125  == 1.6 BLE connection ==
126 126  
127 127  
128 -S31x-LB/LS support BLE remote configure.
128 +S31x-LB support BLE remote configure.
129 129  
130 130  
131 131  BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:
... ... @@ -146,13 +146,10 @@
146 146  
147 147  
148 148  (% border="1" cellspacing="5" style="width:461.818px" %)
149 -|=(% style="width: 102px;background-color:#4F81BD;color:white" %)Model|=(% style="width: 182px; background-color:#4F81BD;color:white" %)Photo|=(% style="width: 176px; background-color:#4F81BD;color:white" %)Probe Info
149 +|=(% style="width: 102px;background-color:#D9E2F3;color:#0070C0" %)Model|=(% style="width: 182px; background-color: rgb(217, 226, 243); color: rgb(0, 112, 192);" %)Photo|=(% style="width: 176px; background-color: rgb(217, 226, 243); color: rgb(0, 112, 192);" %)Probe Info
150 150  |(% style="width:102px" %)(((
151 -S31-LB/LS
152 -)))|(% style="width:182px" %)(((
153 -(% style="text-align:center" %)
154 -[[image:image-20240104165223-7.png]]
155 -)))|(% style="width:176px" %)(((
151 +S31-LB
152 +)))|(% style="width:182px" %)[[image:image-20230527093214-2.jpeg]]|(% style="width:176px" %)(((
156 156  1 x SHT31 Probe
157 157  
158 158  Cable Length : 2 meters
... ... @@ -160,11 +160,8 @@
160 160  
161 161  )))
162 162  |(% style="width:102px" %)(((
163 -S31B-LB/LS
164 -)))|(% style="width:182px" %)(((
165 -(% style="text-align:center" %)
166 -[[image:image-20240104165338-9.png]]
167 -)))|(% style="width:176px" %)(((
160 +S31B-LB
161 +)))|(% style="width:182px" %)[[image:image-20230527093155-1.jpeg]]|(% style="width:176px" %)(((
168 168  1 x SHT31 Probe
169 169  
170 170  Installed in device.
... ... @@ -176,7 +176,6 @@
176 176  
177 177  == 1.9 Mechanical ==
178 178  
179 -=== 1.9.1 for LB version ===
180 180  
181 181  [[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143884058-338.png]]
182 182  
... ... @@ -187,18 +187,12 @@
187 187  [[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143909447-639.png]]
188 188  
189 189  
190 -=== 1.9.2 for LS version ===
183 += 2. Configure S31x-LB to connect to LoRaWAN network =
191 191  
192 -
193 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SN50v3-LB/WebHome/image-20231231203439-3.png?width=886&height=385&rev=1.1||alt="image-20231231203439-3.png"]]
194 -
195 -
196 -= 2. Configure S31x-LB/LS to connect to LoRaWAN network =
197 -
198 198  == 2.1 How it works ==
199 199  
200 200  
201 -The S31x-LB/LS is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the S31x-LB/LS. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
188 +The S31x-LB is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the S31x-LB. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
202 202  
203 203  
204 204  == 2.2 ​Quick guide to connect to LoRaWAN server (OTAA) ==
... ... @@ -209,9 +209,9 @@
209 209  The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
210 210  
211 211  
212 -(% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from S31x-LB/LS.
199 +(% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from S31x-LB.
213 213  
214 -Each S31x-LB/LS is shipped with a sticker with the default device EUI as below:
201 +Each S31x-LB is shipped with a sticker with the default device EUI as below:
215 215  
216 216  [[image:image-20230426084152-1.png||alt="图片-20230426084152-1.png" height="233" width="502"]]
217 217  
... ... @@ -240,10 +240,10 @@
240 240  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-6.png?width=744&height=485&rev=1.1||alt="图片-20220611161308-6.png"]]
241 241  
242 242  
243 -(% style="color:blue" %)**Step 2:**(%%) Activate on S31x-LB/LS
230 +(% style="color:blue" %)**Step 2:**(%%) Activate on S31x-LB
244 244  
245 245  
246 -Press the button for 5 seconds to activate the S31x-LB/LS.
233 +Press the button for 5 seconds to activate the S31x-LB.
247 247  
248 248  (% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:blue" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.
249 249  
... ... @@ -255,15 +255,15 @@
255 255  === 2.3.1 Device Status, FPORT~=5 ===
256 256  
257 257  
258 -Users can use the downlink command(**0x26 01**) to ask S31x-LB/LS to send device configure detail, include device configure status. S31x-LB/LS will uplink a payload via FPort=5 to server.
245 +Users can use the downlink command(**0x26 01**) to ask S31x-LB to send device configure detail, include device configure status. S31x-LB will uplink a payload via FPort=5 to server.
259 259  
260 260  The Payload format is as below.
261 261  
262 262  
263 263  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
264 -|(% colspan="6" style="background-color:#4f81bd; color:white" %)**Device Status (FPORT=5)**
251 +|(% colspan="6" style="background-color:#d9e2f3; color:#0070c0" %)**Device Status (FPORT=5)**
265 265  |(% style="width:103px" %)**Size (bytes)**|(% style="width:72px" %)**1**|**2**|(% style="width:91px" %)**1**|(% style="width:86px" %)**1**|(% style="width:44px" %)**2**
266 -|(% style="width:103px" %)Value|(% style="width:72px" %)Sensor Model|Firmware Version|(% style="width:91px" %)Frequency Band|(% style="width:86px" %)Sub-band|(% style="width:44px" %)BAT
253 +|(% style="width:103px" %)**Value**|(% style="width:72px" %)Sensor Model|Firmware Version|(% style="width:91px" %)Frequency Band|(% style="width:86px" %)Sub-band|(% style="width:44px" %)BAT
267 267  
268 268  Example parse in TTNv3
269 269  
... ... @@ -270,7 +270,7 @@
270 270  [[image:image-20230524144422-1.png||height="174" width="1080"]]
271 271  
272 272  
273 -(% style="color:#037691" %)**Sensor Model**(%%): For S31x-LB/LS, this value is 0x0A
260 +(% style="color:#037691" %)**Sensor Model**(%%): For S31x-LB, this value is 0x0A
274 274  
275 275  (% style="color:#037691" %)**Firmware Version**(%%): 0x0100, Means: v1.0.0 version
276 276  
... ... @@ -329,9 +329,9 @@
329 329  Sensor Data is uplink via FPORT=2
330 330  
331 331  (% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
332 -|=(% style="width: 60px;background-color:#4F81BD;color:white" %)(((
319 +|=(% style="width: 60px;background-color:#D9E2F3;color:#0070C0" %)(((
333 333  **Size(bytes)**
334 -)))|=(% style="width: 40px;background-color:#4F81BD;color:white" %)2|=(% style="width: 90px;background-color:#4F81BD;color:white" %)4|=(% style="width: 150px; background-color: #4F81BD;color:white" %)1|=(% style="width: 80px; background-color: #4F81BD;color:white" %)**2**|=(% style="width: 80px; background-color: #4F81BD;color:white" %)2
321 +)))|=(% style="width: 40px;background-color:#D9E2F3;color:#0070C0" %)2|=(% style="width: 90px;background-color:#D9E2F3;color:#0070C0" %)4|=(% style="width: 150px; background-color: #D9E2F3;color:#0070C0" %)1|=(% style="width: 80px; background-color: #D9E2F3;color:#0070C0" %)**2**|=(% style="width: 80px; background-color: #D9E2F3;color:#0070C0" %)2
335 335  |(% style="width:99px" %)Value|(% style="width:69px" %)(((
336 336  Battery
337 337  )))|(% style="width:130px" %)(((
... ... @@ -404,19 +404,19 @@
404 404  == 2.5 Datalog Feature ==
405 405  
406 406  
407 -Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, S31x-LB/LS will store the reading for future retrieving purposes.
394 +Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, S31x-LB will store the reading for future retrieving purposes.
408 408  
409 409  
410 410  === 2.5.1 Ways to get datalog via LoRaWAN ===
411 411  
412 412  
413 -Set [[PNACKMD=1>>||anchor="H2.5.4DatalogUplinkpayload28FPORT3D329"]], S31x-LB/LS will wait for ACK for every uplink, when there is no LoRaWAN network,S31x-LB/LS will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
400 +Set [[PNACKMD=1>>||anchor="H2.5.4DatalogUplinkpayload28FPORT3D329"]], S31x-LB will wait for ACK for every uplink, when there is no LoRaWAN network,S31x-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
414 414  
415 415  * (((
416 -a) S31x-LB/LS will do an ACK check for data records sending to make sure every data arrive server.
403 +a) S31x-LB will do an ACK check for data records sending to make sure every data arrive server.
417 417  )))
418 418  * (((
419 -b) S31x-LB/LS will send data in **CONFIRMED Mode** when PNACKMD=1, but S31x-LB/LS won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if S31x-LB/LS gets a ACK, S31x-LB/LS will consider there is a network connection and resend all NONE-ACK messages.
406 +b) S31x-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but S31x-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if S31x-LB gets a ACK, S31x-LB will consider there is a network connection and resend all NONE-ACK messages.
420 420  )))
421 421  
422 422  Below is the typical case for the auto-update datalog feature (Set PNACKMD=1)
... ... @@ -427,7 +427,7 @@
427 427  === 2.5.2 Unix TimeStamp ===
428 428  
429 429  
430 -S31x-LB/LS uses Unix TimeStamp format based on
417 +S31x-LB uses Unix TimeStamp format based on
431 431  
432 432  [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-11.png?width=627&height=97&rev=1.1||alt="图片-20220523001219-11.png" height="97" width="627"]]
433 433  
... ... @@ -446,7 +446,7 @@
446 446  
447 447  User need to set (% style="color:blue" %)**SYNCMOD=1**(%%) to enable sync time via MAC command.
448 448  
449 -Once S31x-LB/LS Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to S31x-LB/LS. If S31x-LB/LS fails to get the time from the server, S31x-LB/LS will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
436 +Once S31x-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to S31x-LB. If S31x-LB fails to get the time from the server, S31x-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
450 450  
451 451  (% style="color:red" %)**Note: LoRaWAN Server need to support LoRaWAN v1.0.3(MAC v1.0.3) or higher to support this MAC command feature, Chirpstack,TTN V3 v3 and loriot support but TTN V3 v2 doesn't support. If server doesn't support this command, it will through away uplink packet with this command, so user will lose the packet with time request for TTN V3 v2 if SYNCMOD=1.**
452 452  
... ... @@ -459,9 +459,9 @@
459 459  **Retrieval data payload:**
460 460  
461 461  (% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
462 -|=(% style="width: 60px;background-color:#4F81BD;color:white" %)(((
449 +|=(% style="width: 60px;background-color:#D9E2F3;color:#0070C0" %)(((
463 463  **Size(bytes)**
464 -)))|=(% style="width: 40px; background-color:#4F81BD;color:white" %)**2**|=(% style="width: 55px; background-color:#4F81BD;color:white" %)**2**|=(% style="width: 65px; background-color:#4F81BD;color:white" %)**2**|=(% style="width: 180px; background-color:#4F81BD;color:white" %)**1**|=(% style="width: 100px; background-color:#4F81BD;color:white" %)**4**
451 +)))|=(% style="width: 40px; background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 55px; background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 65px; background-color:#D9E2F3;color:#0070C0" %)**2**|=(% style="width: 180px; background-color:#D9E2F3;color:#0070C0" %)**1**|=(% style="width: 100px; background-color:#D9E2F3;color:#0070C0" %)**4**
465 465  |(% style="width:103px" %)Value|(% style="width:68px" %)(((
466 466  ignore
467 467  )))|(% style="width:104px" %)(((
... ... @@ -505,7 +505,7 @@
505 505  
506 506  **Example:**
507 507  
508 -If S31x-LB/LS has below data inside Flash:
495 +If S31x-LB has below data inside Flash:
509 509  
510 510  [[image:image-20230524114654-2.png]]
511 511  
... ... @@ -517,7 +517,7 @@
517 517   Stop time: 646D856C= time 23/5/24 03:33:00
518 518  
519 519  
520 -**S31x-LB/LS will uplink this payload.**
507 +**S31x-LB will uplink this payload.**
521 521  
522 522  [[image:image-20230524114826-3.png||height="448" width="1244"]]
523 523  
... ... @@ -555,7 +555,7 @@
555 555  == 2.6 Temperature Alarm Feature ==
556 556  
557 557  
558 -S31x-LB/LS work flow with Alarm feature.
545 +S31x-LB work flow with Alarm feature.
559 559  
560 560  
561 561  [[image:image-20230524110125-3.png||height="768" width="1115"]]
... ... @@ -565,7 +565,7 @@
565 565  == 2.7 Frequency Plans ==
566 566  
567 567  
568 -The S31x-LB/LS uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
555 +The S31x-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
569 569  
570 570  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]
571 571  
... ... @@ -576,12 +576,12 @@
576 576  **Firmware download link: **[[https:~~/~~/www.dropbox.com/sh/fis3g6nmhv0eokg/AAC6BcCZaX4BdqZkduUvZ3jIa?dl=0>>https://www.dropbox.com/sh/fis3g6nmhv0eokg/AAC6BcCZaX4BdqZkduUvZ3jIa?dl=0]]
577 577  
578 578  
579 -= 3. Configure S31x-LB/LS =
566 += 3. Configure S31x-LB =
580 580  
581 581  == 3.1 Configure Methods ==
582 582  
583 583  
584 -S31x-LB/LS supports below configure method:
571 +S31x-LB supports below configure method:
585 585  
586 586  * AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
587 587  * AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].
... ... @@ -600,10 +600,10 @@
600 600  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
601 601  
602 602  
603 -== 3.3 Commands special design for S31x-LB/LS ==
590 +== 3.3 Commands special design for S31x-LB ==
604 604  
605 605  
606 -These commands only valid for S31x-LB/LS, as below:
593 +These commands only valid for S31x-LB, as below:
607 607  
608 608  
609 609  === 3.3.1 Set Transmit Interval Time ===
... ... @@ -614,7 +614,7 @@
614 614  (% style="color:blue" %)**AT Command: AT+TDC**
615 615  
616 616  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
617 -|=(% style="width: 156px;background-color:#4F81BD;color:white" %)**Command Example**|=(% style="width: 137px;background-color:#4F81BD;color:white" %)**Function**|=(% style="background-color:#4F81BD;color:white" %)**Response**
604 +|=(% style="width: 156px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 137px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="background-color:#D9E2F3;color:#0070C0" %)**Response**
618 618  |(% style="width:156px" %)AT+TDC=?|(% style="width:137px" %)Show current transmit Interval|(((
619 619  30000
620 620  OK
... ... @@ -727,7 +727,7 @@
727 727  (% style="color:blue" %)**AT Command: AT+INTMOD**
728 728  
729 729  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
730 -|=(% style="width: 155px;background-color:#4F81BD;color:white" %)**Command Example**|=(% style="width: 197px;background-color:#4F81BD;color:white" %)**Function**|=(% style="width: 158px;background-color:#4F81BD;color:white" %)**Response**
717 +|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 197px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 158px;background-color:#D9E2F3;color:#0070C0" %)**Response**
731 731  |(% style="width:154px" %)AT+INTMOD=?|(% style="width:196px" %)Show current interrupt mode|(% style="width:157px" %)(((
732 732  0
733 733  OK
... ... @@ -764,7 +764,7 @@
764 764  (% style="color:blue" %)**AT Command: AT+5VT**
765 765  
766 766  (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
767 -|=(% style="width: 155px;background-color:#4F81BD;color:white" %)**Command Example**|=(% style="width: 197px;background-color:#4F81BD;color:white" %)**Function**|=(% style="width: 158px;background-color:#4F81BD;color:white" %)**Response**
754 +|=(% style="width: 155px;background-color:#D9E2F3;color:#0070C0" %)**Command Example**|=(% style="width: 197px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 158px;background-color:#D9E2F3;color:#0070C0" %)**Response**
768 768  |(% style="width:154px" %)AT+5VT=?|(% style="width:196px" %)Show 5V open time.|(% style="width:157px" %)0 (default)
769 769  OK
770 770  |(% style="width:154px" %)AT+5VT=1000|(% style="width:196px" %)Close after a delay of 1000 milliseconds.|(% style="width:157px" %)OK
... ... @@ -781,7 +781,7 @@
781 781  = 4. Battery & Power Consumption =
782 782  
783 783  
784 -S31x-LB use ER26500 + SPC1520 battery pack and S31x-LS use 3000mAh Recharable Battery with Solar Panel. See below link for detail information about the battery info and how to replace.
771 +S31x-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
785 785  
786 786  [[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
787 787  
... ... @@ -790,7 +790,7 @@
790 790  
791 791  
792 792  (% class="wikigeneratedid" %)
793 -User can change firmware S31x-LB/LS to:
780 +User can change firmware S31x-LB to:
794 794  
795 795  * Change Frequency band/ region.
796 796  * Update with new features.
... ... @@ -811,7 +811,7 @@
811 811  = 7. Order Info =
812 812  
813 813  
814 -Part Number: (% style="color:blue" %)**S31-LB-XX / S31B-LB-XX**(%%)**  or  (% style="color:blue" %)S31-LS-XX / S31B-LS-XX(%%)**
801 +Part Number: (% style="color:blue" %)**S31-LB-XX  / S31B-LB-XX**
815 815  
816 816  (% style="color:red" %)**XX**(%%): The default frequency band
817 817  
... ... @@ -836,7 +836,7 @@
836 836  
837 837  (% style="color:#037691" %)**Package Includes**:
838 838  
839 -* S31x-LB or S31x-LS LoRaWAN Temperature & Humidity Sensor
826 +* S31x-LB LoRaWAN Temperature & Humidity Sensor
840 840  
841 841  (% style="color:#037691" %)**Dimension and weight**:
842 842  
image-20240104165223-7.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -30.6 KB
Content
image-20240104165302-8.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -17.5 KB
Content
image-20240104165338-9.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -15.7 KB
Content