Skip to Content
Last modified by Mengting Qiu on 2025/07/01 15:58
From version 31.2
edited by kai
on 2023/05/06 15:45
Change comment: There is no comment for this version
To version 9.1
edited by Edwin Chen
on 2023/04/16 13:43
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.kai
1 +XWiki.Edwin
Content
... ... @@ -1,9 +1,6 @@
1 -(% style="text-align:center" %)
2 -[[image:S31-B.jpg]]
1 +
3 3  
4 4  
5 -
6 -
7 7  **Table of Contents：**
8 8  
9 9  {{toc/}}
... ... @@ -17,19 +17,20 @@
17 17  
18 18  == 1.1 What is S31x-LB LoRaWAN Temperature & Humidity Sensor ==
19 19  
20 -The Dragino S31x-LB is a **LoRaWAN Temperature and Humidity Sensor** for Internet of Things solution. It is used to measure the **surrounding environment temperature and relative air humidity precisely**, and then upload to IoT server via LoRaWAN wireless protocol.
21 21  
22 -The temperature & humidity sensor used in S31x-LB is SHT31, which is fully calibrated, linearized, and temperature compensated digital output from Sensirion, it provides a strong reliability and long-term stability. The SHT31 is fixed in a **waterproof anti-condensation casing** for long term use.
18 +The Dragino S31x-LB is a (% style="color:blue" %)**LoRaWAN Temperature and Humidity Sensor**(%%) for Internet of Things solution. It is used to measure the (% style="color:blue" %)**surrounding environment temperature and relative air humidity precisely**(%%), and then upload to IoT server via LoRaWAN wireless protocol.
23 23  
20 +The temperature & humidity sensor used in S31x-LB is SHT31, which is fully calibrated, linearized, and temperature compensated digital output from Sensirion, it provides a strong reliability and long-term stability. The SHT31 is fixed in a (% style="color:blue" %)**waterproof anti-condensation casing**(%%) for long term use.
21 +
24 24  The LoRa wireless technology used in S31x-LB allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
25 25  
26 -S31x-LB supports **Temperature & Humdity alarm feature,** user can set temperature alarm for instant notice. S31x-LB supports Datalog feature, it can save the data when there is no LoRaWAN network and uplink when network recover.
24 +S31x-LB supports (% style="color:blue" %)**Temperature & Humdity alarm feature,**(%%) user can set temperature alarm for instant notice. S31x-LB supports Datalog feature, it can save the data when there is no LoRaWAN network and uplink when network recover.
27 27  
28 28  S31x-LB has max 3 probes which measure maximum 3 temperature points.
29 29  
30 -S31x-LB **supports BLE configure** and **wireless OTA update** which make user easy to use.
28 +S31x-LB (% style="color:blue" %)**supports BLE configure**(%%) and (% style="color:blue" %)**wireless OTA update**(%%) which make user easy to use.
31 31  
32 -S31x-LB is powered by **8500mAh Li-SOCI2 battery**, it is designed for long term use up to 5 years.
30 +S31x-LB is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), it is designed for long term use up to 5 years.
33 33  
34 34  Each S31x-LB is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
35 35  
... ... @@ -104,8 +104,8 @@
104 104  [[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675071855856-879.png]]
105 105  
106 106  
107 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
108 -|=(% style="width: 167px;background-color:#D9E2F3;color:#0070C0" %)**Behavior on ACT**|=(% style="width: 117px;background-color:#D9E2F3;color:#0070C0" %)**Function**|=(% style="width: 225px;background-color:#D9E2F3;color:#0070C0" %)**Action**
105 +(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)
106 +|=(% style="width: 167px;" %)**Behavior on ACT**|=(% style="width: 117px;" %)**Function**|=(% style="width: 225px;" %)**Action**
109 109  |(% style="width:167px" %)Pressing ACT between 1s < time < 3s|(% style="width:117px" %)Send an uplink|(% style="width:225px" %)(((
110 110  If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, (% style="color:blue" %)**blue led** (%%)will blink once.
111 111  Meanwhile, BLE module will be active and user can connect via BLE to configure device.
... ... @@ -120,7 +120,7 @@
120 120  == 1.6 BLE connection ==
121 121  
122 122  
123 -S31x-LB support BLE remote configure.
121 +D2x-LB support BLE remote configure.
124 124  
125 125  
126 126  BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:
... ... @@ -135,9 +135,9 @@
135 135  == 1.7  Hardware Variant ==
136 136  
137 137  
138 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)
139 -|=(% style="width: 102px;background-color:#D9E2F3;color:#0070C0" %)Model|=(% style="width: 190px;background-color:#D9E2F3;color:#0070C0" %)Photo|=(% style="width: 218px;background-color:#D9E2F3;color:#0070C0" %)Probe Info
140 -|(% style="width:102px" %)S31-LB|(% style="width:190px" %) |(% style="width:297px" %)(((
136 +(% border="1" cellspacing="10" style="background-color:#f7faff; width:510px" %)
137 +|=(% style="width: 102px;" %)Model|=(% style="width: 190px;" %)Photo|=(% style="width: 297px;" %)Probe Info
138 +|(% style="width:102px" %)**S31-LB**|(% style="width:190px" %) |(% style="width:297px" %)(((
141 141  1 x SHT31 Probe
142 142  
143 143  Cable Length : 2 meters
... ... @@ -144,7 +144,7 @@
144 144  
145 145  
146 146  )))
147 -|(% style="width:102px" %)S31B-LB|(% style="width:190px" %) |(% style="width:297px" %)(((
145 +|(% style="width:102px" %)**S31B-LB**|(% style="width:190px" %) |(% style="width:297px" %)(((
148 148  1 x SHT31 Probe
149 149  
150 150  Installed in device.
... ... @@ -179,6 +179,10 @@
179 179  
180 180  Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.
181 181  
180 +
181 +[[image:1675144005218-297.png]]
182 +
183 +
182 182  The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
183 183  
184 184  
... ... @@ -186,31 +186,32 @@
186 186  
187 187  Each S31x-LB is shipped with a sticker with the default device EUI as below:
188 188  
189 -[[image:image-20230426084152-1.png||alt="图片-20230426084152-1.png" height="233" width="502"]]
191 +[[image:image-20230131134744-2.jpeg]]
190 190  
191 191  
194 +
192 192  You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
193 193  
194 194  
195 195  (% style="color:blue" %)**Register the device**
196 196  
197 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/1654935135620-998.png?rev=1.1||alt="1654935135620-998.png"]]
200 +[[image:1675144099263-405.png]]
198 198  
199 199  
200 200  (% style="color:blue" %)**Add APP EUI and DEV EUI**
201 201  
202 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-4.png?width=753&height=551&rev=1.1||alt="图片-20220611161308-4.png"]]
205 +[[image:1675144117571-832.png]]
203 203  
204 204  
205 205  (% style="color:blue" %)**Add APP EUI in the application**
206 206  
207 207  
208 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-5.png?width=742&height=601&rev=1.1||alt="图片-20220611161308-5.png"]]
211 +[[image:1675144143021-195.png]]
209 209  
210 210  
211 211  (% style="color:blue" %)**Add APP KEY**
212 212  
213 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-6.png?width=744&height=485&rev=1.1||alt="图片-20220611161308-6.png"]]
216 +[[image:1675144157838-392.png]]
214 214  
215 215  
216 216  (% style="color:blue" %)**Step 2:**(%%) Activate on S31x-LB
... ... @@ -233,14 +233,14 @@
233 233  The Payload format is as below.
234 234  
235 235  
236 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
237 -|(% colspan="6" style="background-color:#d9e2f3; color:#0070c0" %)**Device Status (FPORT=5)**
239 +(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)
240 +|(% colspan="6" %)**Device Status (FPORT=5)**
238 238  |(% style="width:103px" %)**Size (bytes)**|(% style="width:72px" %)**1**|**2**|(% style="width:91px" %)**1**|(% style="width:86px" %)**1**|(% style="width:44px" %)**2**
239 239  |(% style="width:103px" %)**Value**|(% style="width:72px" %)Sensor Model|Firmware Version|(% style="width:91px" %)Frequency Band|(% style="width:86px" %)Sub-band|(% style="width:44px" %)BAT
240 240  
241 241  Example parse in TTNv3
242 242  
243 -[[image:image-20230421171614-1.png||alt="图片-20230421171614-1.png"]]
246 +[[image:image-20230415153147-2.png||height="220" width="1120"]]
244 244  
245 245  
246 246  (% style="color:#037691" %)**Sensor Model**(%%): For S31x-LB, this value is 0x0A
... ... @@ -301,24 +301,25 @@
301 301  
302 302  Sensor Data is uplink via FPORT=2
303 303  
304 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
305 -|=(% style="width: 90px;background-color:#D9E2F3" %)(((
307 +|=(((
306 306  **Size(bytes)**
307 -)))|=(% style="width: 80px;background-color:#D9E2F3" %)2|=(% style="width: 90px;background-color:#D9E2F3" %)4|=(% style="width:80px;background-color:#D9E2F3" %)1|=(% style="width: 80px;background-color:#D9E2F3" %)**2**|=(% style="width: 80px;background-color:#D9E2F3" %)2
308 -|(% style="width:99px" %)**Value**|(% style="width:69px" %)(((
309 -[[Battery>>||anchor="HBattery:"]]
310 -)))|(% style="width:130px" %)(((
311 -[[Unix TimeStamp>>||anchor="H2.5.2UnixTimeStamp"]]
312 -)))|(% style="width:91px" %)(((
313 -[[Alarm Flag>>||anchor="HAlarmFlag26MOD:"]]
314 -)))|(% style="width:103px" %)(((
315 -[[Temperature>>||anchor="HTemperature:"]]
316 -)))|(% style="width:80px" %)(((
317 -[[Humidity>>||anchor="HHumidity:"]]
309 +)))|=2|=4|=1|=**2**|=2
310 +|**Value**|(((
311 +[[Battery>>path:#HBattery:]]
312 +)))|(((
313 +[[Unix TimeStamp>>path:#H2.4.1UnixTimeStamp]]
314 +)))|(((
315 +[[Alarm Flag>>path:#HAlarmFlag26MOD:]]
316 +)))|(((
317 +[[Temperature>>path:#HTemperature:]]
318 +)))|(((
319 +[[Humidity>>path:#HHumidity:]]
318 318  )))
319 319  
320 -==== (% style="color:#4472c4" %)**Battery**(%%) ====
321 321  
323 +
324 +==== (% style="color:#4472c4" %)**Battery:**(%%) ====
325 +
322 322  Sensor Battery Level.
323 323  
324 324  Ex1: 0x0B45 = 2885mV
... ... @@ -327,7 +327,7 @@
327 327  
328 328  
329 329  
330 -==== (% style="color:#4472c4" %)**Temperature**(%%) ====
334 +==== (% style="color:#4472c4" %)**Temperature:**(%%) ====
331 331  
332 332  **Example**:
333 333  
... ... @@ -338,13 +338,13 @@
338 338  （FF3F & 8000：Judge whether the highest bit is 1, when the highest bit is 1, it is negative）
339 339  
340 340  
341 -==== (% style="color:#4472c4" %)**Humidity**(%%) ====
345 +==== (% style="color:#4472c4" %)**Humidity:**(%%) ====
342 342  
343 343  
344 344  Read:0x(0197)=412    Value:  412 / 10=41.2, So 41.2%
345 345  
346 346  
347 -==== (% style="color:#4472c4" %)**Alarm Flag& MOD**(%%) ====
351 +==== (% style="color:#4472c4" %)**Alarm Flag& MOD:**(%%) ====
348 348  
349 349  
350 350  **Example:**
... ... @@ -360,44 +360,41 @@
360 360  
361 361  == 2.4 Payload Decoder file ==
362 362  
367 +In TTN, use can add a custom payload so it shows friendly. 
363 363  
364 -In TTN, use can add a custom payload so it shows friendly reading
369 +In the page **Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder** to add the decoder from: [[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/LSN50v2-S31%26S31B >>https://github.com/dragino/dragino-end-node-decoder/tree/main/LSN50v2-S31%26S31B]]
365 365  
366 -In the page (% style="color:#037691" %)**Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder**(%%) to add the decoder from:
367 367  
368 -[[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/LSN50v2-S31%26S31B >>https://github.com/dragino/dragino-end-node-decoder/tree/main/LSN50v2-S31%26S31B]]
369 -
370 -
371 371  == 2.5 Datalog Feature ==
372 372  
373 373  
374 -Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, S31x-LB will store the reading for future retrieving purposes.
375 +Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, D2x-LB will store the reading for future retrieving purposes.
375 375  
376 376  
377 377  === 2.5.1 Ways to get datalog via LoRaWAN ===
378 378  
379 379  
380 -Set [[PNACKMD=1>>||anchor="H2.5.4DatalogUplinkpayloadA028FPORT3D329"]], S31x-LB will wait for ACK for every uplink, when there is no LoRaWAN network,S31x-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
381 +Set [[PNACKMD=1>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/#H4.13AutoSendNone-ACKmessages]], D2x-LB will wait for ACK for every uplink, when there is no LoRaWAN network,D2x-LB will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
381 381  
382 -* a) S31x-LB will do an ACK check for data records sending to make sure every data arrive server.
383 -* b) S31x-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but S31x-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if S31x-LB gets a ACK, S31x-LB will consider there is a network connection and resend all NONE-ACK messages.
383 +* a) D2x-LB will do an ACK check for data records sending to make sure every data arrive server.
384 +* b) D2x-LB will send data in **CONFIRMED Mode** when PNACKMD=1, but D2x-LB won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if D2x-LB gets a ACK, D2x-LB will consider there is a network connection and resend all NONE-ACK Message.
384 384  
385 385  Below is the typical case for the auto-update datalog feature (Set PNACKMD=1)
386 386  
387 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220703111700-2.png?width=1119&height=381&rev=1.1||alt="图片-20220703111700-2.png" height="381" width="1119"]]
388 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220703111700-2.png?width=1119&height=381&rev=1.1||alt="image-20220703111700-2.png" height="381" width="1119"]]
388 388  
389 389  === 2.5.2 Unix TimeStamp ===
390 390  
391 391  
392 -S31x-LB uses Unix TimeStamp format based on
393 +LHT65N uses Unix TimeStamp format based on
393 393  
394 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-11.png?width=627&height=97&rev=1.1||alt="图片-20220523001219-11.png" height="97" width="627"]]
395 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-11.png?width=627&height=97&rev=1.1||alt="image-20220523001219-11.png" height="97" width="627"]]
395 395  
396 396  User can get this time from link:  [[https:~~/~~/www.epochconverter.com/>>url:https://www.epochconverter.com/]] :
397 397  
398 398  Below is the converter example
399 399  
400 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-12.png?width=720&height=298&rev=1.1||alt="图片-20220523001219-12.png" height="298" width="720"]]
401 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-12.png?width=720&height=298&rev=1.1||alt="image-20220523001219-12.png" height="298" width="720"]]
401 401  
402 402  So, we can use AT+TIMESTAMP=1611889405 or downlink 3060137afd00 to set the current time 2021 – Jan ~-~- 29 Friday 03:03:25
403 403  
... ... @@ -405,33 +405,33 @@
405 405  === 2.5.3 Set Device Time ===
406 406  
407 407  
408 -User need to set (% style="color:blue" %)**SYNCMOD=1**(%%) to enable sync time via MAC command.
409 +User need to set SYNCMOD=1 to enable sync time via MAC command.
409 409  
410 -Once S31x-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to S31x-LB. If S31x-LB fails to get the time from the server, S31x-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
411 +Once D2x-LB Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to D2x-LB. If D2x-LB fails to get the time from the server, D2x-LB will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
411 411  
412 -(% style="color:red" %)**Note: LoRaWAN Server need to support LoRaWAN v1.0.3(MAC v1.0.3) or higher to support this MAC command feature, Chirpstack,TTN V3 v3 and loriot support but TTN V3 v2 doesn't support. If server doesn't support this command, it will through away uplink packet with this command, so user will lose the packet with time request for TTN V3 v2 if SYNCMOD=1.**
413 +**Note: LoRaWAN Server need to support LoRaWAN v1.0.3(MAC v1.0.3) or higher to support this MAC command feature, Chirpstack,TTN V3 v3 and loriot support but TTN V3 v2 doesn't support. If server doesn't support this command, it will through away uplink packet with this command, so user will lose the packet with time request for TTN V3 v2 if SYNCMOD=1.**
413 413  
414 414  
415 -=== 2.5.4 Datalog Uplink payload (FPORT~=3) ===
416 +=== 2.5.4 Datalog Uplink payload  （FPORT~=3） ===
416 416  
417 417  
418 -The Datalog uplinks will use below payload format.
419 +The Datalog poll reply uplink will use below payload format.
419 419  
420 420  **Retrieval data payload:**
421 421  
422 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:510px" %)
423 -|=(% style="width: 80px;background-color:#D9E2F3" %)(((
423 +(% style="width:858px" %)
424 +|=(% style="width: 103px;" %)(((
424 424  **Size(bytes)**
425 -)))|=(% style="width: 60px; background-color: rgb(217, 226, 243);" %)**2**|=(% style="width: 60px; background-color: rgb(217, 226, 243);" %)**2**|=(% style="width: 120px; background-color: rgb(217, 226, 243);" %)**2**|=(% style="width: 103px; background-color: rgb(217, 226, 243);" %)**1**|=(% style="width: 85px; background-color: rgb(217, 226, 243);" %)**4**
426 -|(% style="width:103px" %)**Value**|(% style="width:54px" %)(((
426 +)))|=(% style="width: 129px;" %)**2**|=(% style="width: 114px;" %)**2**|=(% style="width: 217px;" %)**2**|=(% style="width: 153px;" %)**1**|=(% style="width: 139px;" %)**4**
427 +|(% style="width:103px" %)**Value**|(% style="width:129px" %)(((
427 427  [[Temp_Black>>||anchor="HTemperatureBlack:"]]
428 -)))|(% style="width:51px" %)[[Temp_White>>||anchor="HTemperatureWhite:"]]|(% style="width:89px" %)[[Temp_ Red or Temp _White>>||anchor="HTemperatureREDorTemperatureWhite:"]]|(% style="width:103px" %)Poll message flag & Ext|(% style="width:54px" %)[[Unix Time Stamp>>||anchor="H2.5.2UnixTimeStamp"]]
429 +)))|(% style="width:114px" %)[[Temp_White>>||anchor="HTemperatureWhite:"]]|(% style="width:217px" %)[[Temp_ Red or Temp _White>>||anchor="HTemperatureREDorTemperatureWhite:"]]|(% style="width:153px" %)Poll message flag & Ext|(% style="width:139px" %)[[Unix Time Stamp>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/#H2.6.2UnixTimeStamp]]
429 429  
430 430  **Poll message flag & Ext:**
431 431  
432 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20221006192726-1.png?width=754&height=112&rev=1.1||alt="图片-20221006192726-1.png" height="112" width="754"]]
433 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20221006192726-1.png?width=754&height=112&rev=1.1||alt="image-20221006192726-1.png" height="112" width="754"]]
433 433  
434 -**No ACK Message**:  1: This message means this payload is fromn Uplink Message which doesn't get ACK from the server before ( for **PNACKMD=1** feature)
435 +**No ACK Message**:  1: This message means this payload is fromn Uplink Message which doesn't get ACK from the server before ( for [[PNACKMD=1>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/#H4.13AutoSendNone-ACKmessages]] feature)
435 435  
436 436  **Poll Message Flag**: 1: This message is a poll message reply.
437 437  
... ... @@ -451,12 +451,11 @@
451 451  
452 452  If devise doesn't have any data in the polling time. Device will uplink 11 bytes of 0   
453 453  
454 -
455 455  **Example:**
456 456  
457 -If S31x-LB has below data inside Flash:
457 +If D2x-LB has below data inside Flash:
458 458  
459 -[[image:1682646494051-944.png]]
459 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523144455-1.png?width=735&height=335&rev=1.1||alt="image-20220523144455-1.png" height="335" width="735"]]
460 460  
461 461  If user sends below downlink command: 3160065F9760066DA705
462 462  
... ... @@ -464,72 +464,65 @@
464 464  
465 465   Stop time: 60066DA7= time 21/1/19 05:27:03
466 466  
467 +**LHT65N will uplink this payload.**
467 467  
468 -**S31x-LB will uplink this payload.**
469 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-13.png?width=727&height=421&rev=1.1||alt="image-20220523001219-13.png" height="421" width="727"]]
469 469  
470 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-13.png?width=727&height=421&rev=1.1||alt="图片-20220523001219-13.png" height="421" width="727"]]
471 -
472 -(((
473 473  __**7FFF089801464160065F97**__ **__7FFF__ __088E__ __014B__ __41__ __60066009__** 7FFF0885014E41600660667FFF0875015141600662BE7FFF086B015541600665167FFF08660155416006676E7FFF085F015A41600669C67FFF0857015D4160066C1E
474 -)))
475 475  
476 -(((
477 477  Where the first 11 bytes is for the first entry:
478 -)))
479 479  
480 -(((
481 481  7FFF089801464160065F97
482 -)))
483 483  
484 -(((
485 -**Ext sensor data**=0x7FFF/100=327.67
486 -)))
477 +Ext sensor data=0x7FFF/100=327.67
487 487  
488 -(((
489 -**Temp**=0x088E/100=22.00
490 -)))
479 +Temp=0x088E/100=22.00
491 491  
492 -(((
493 -**Hum**=0x014B/10=32.6
494 -)))
481 +Hum=0x014B/10=32.6
495 495  
496 -(((
497 -**poll message flag & Ext**=0x41,means reply data,Ext=1
498 -)))
483 +poll message flag & Ext=0x41,means reply data,Ext=1
499 499  
500 -(((
501 -**Unix time** is 0x60066009=1611030423s=21/1/19 04:27:03
502 -)))
485 +Unix time is 0x60066009=1611030423s=21/1/19 04:27:03
503 503  
504 504  
505 -(% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的(% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的
488 +(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||data-widget="image" draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="Click and drag to resize" %)​(% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||data-widget="image" draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||draggable="true" height="15" role="presentation" title="Click and drag to move" width="15"]](% aria-label="Data URI image image widget" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="Click and drag to resize" %)​
506 506  
507 507  == 2.6 Temperature Alarm Feature ==
508 508  
509 509  
510 -S31x-LB work flow with Alarm feature.
493 +D2x-LB work flow with Alarm feature.
511 511  
512 512  
513 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-D20-D22-D23%20LoRaWAN%20Temperature%20Sensor%20User%20Manual/WebHome/image-20220623090437-1.png?rev=1.1||alt="图片-20220623090437-1.png"]]
496 +[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-D20-D22-D23%20LoRaWAN%20Temperature%20Sensor%20User%20Manual/WebHome/image-20220623090437-1.png?rev=1.1||alt="image-20220623090437-1.png"]]
514 514  
515 515  
499 +
516 516  == 2.7 Frequency Plans ==
517 517  
518 518  
519 -The S31x-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
503 +The D2x-LB uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
520 520  
521 521  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]
522 522  
523 523  
524 -= 3. Configure S31x-LB =
508 +== 2.8 ​Firmware Change Log ==
525 525  
526 -== 3.1 Configure Methods ==
527 527  
511 +**Firmware download link:**
528 528  
529 -S31x-LB supports below configure method:
513 +[[https:~~/~~/www.dropbox.com/sh/gf1glloczbzz19h/AABbuYI4WY6VdAmpXo6o1V2Ka?dl=0>>url:https://www.dropbox.com/sh/gf1glloczbzz19h/AABbuYI4WY6VdAmpXo6o1V2Ka?dl=0]]
530 530  
515 +
516 +
517 += 3. Configure D2x-LB =
518 +
519 +== 3.1 Configure Methods: ==
520 +
521 +
522 +D2x-LB supports below configure method:
523 +
531 531  * AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
532 -* AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].
525 +* AT Command via UART Connection : See [[FAQ>>||anchor="H7.FAQ"]].
533 533  * LoRaWAN Downlink.  Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
534 534  
535 535  == 3.2 General Commands ==
... ... @@ -545,10 +545,10 @@
545 545  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
546 546  
547 547  
548 -== 3.3 Commands special design for S31x-LB ==
541 +== 3.3 Commands special design for D2x-LB ==
549 549  
550 550  
551 -These commands only valid for S31x-LB, as below:
544 +These commands only valid for D2x-LB, as below:
552 552  
553 553  
554 554  === 3.3.1 Set Transmit Interval Time ===
... ... @@ -558,8 +558,8 @@
558 558  
559 559  (% style="color:blue" %)**AT Command: AT+TDC**
560 560  
561 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
562 -|=(% style="width: 156px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 137px;background-color:#D9E2F3" %)**Function**|=(% style="background-color:#D9E2F3" %)**Response**
554 +(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)
555 +|=(% style="width: 156px;" %)**Command Example**|=(% style="width: 137px;" %)**Function**|=**Response**
563 563  |(% style="width:156px" %)AT+TDC=?|(% style="width:137px" %)Show current transmit Interval|(((
564 564  30000
565 565  OK
... ... @@ -584,69 +584,74 @@
584 584  
585 585  Send a LoRaWAN downlink to ask device send Alarm settings.
586 586  
587 -(% style="color:blue" %)**Downlink Payload:  **(%%)0x26 01
580 +* (% style="color:#037691" %)**Downlink Payload:  **(%%)0x26 01
588 588  
589 589  Sensor will upload Device Status via FPORT=5. See payload section for detail.
590 590  
591 591  
592 -=== 3.3.3 Set Temperature Alarm Threshold ===
585 +=== 3.3.3 Set Alarm Thredhold ===
593 593  
594 -* (% style="color:blue" %)**AT Command:**
595 595  
596 -(% style="color:#037691" %)**AT+SHTEMP=min,max**
588 +(% style="color:#4472c4" %)**1.  Set for All Probes:**
597 597  
598 -* When min=0, and max≠0, Alarm higher than max
599 -* When min≠0, and max=0, Alarm lower than min
600 -* When min≠0 and max≠0, Alarm higher than max or lower than min
590 +(% style="color:#037691" %)**AT+18ALARM=min,max**
601 601  
602 -Example:
592 +* When min=0, and max≠0, Alarm trigger when higher than max
593 +* When min≠0, and max=0, Alarm trigger when lower than min
594 +* When min≠0 and max≠0, Alarm trigger when higher than max or lower than min
603 603  
604 - AT+SHTEMP=0,30   ~/~/ Alarm when temperature higher than 30.
596 +**Example:**
605 605  
606 -* (% style="color:blue" %)**Downlink Payload:**
598 + AT+18ALARM=-10,30  ~/~/ Alarm when < -10 or higher than 30.
607 607  
608 -(% style="color:#037691" %)**0x(0C 01 00 1E)**  (%%) ~/~/ Set AT+SHTEMP=0,30
609 609  
610 -(% style="color:red" %)**(note: 3^^rd^^ byte= 0x00 for low limit(not set), 4^^th^^ byte = 0x1E for high limit: 30)**
601 +* (% style="color:#037691" %)**Downlink Payload:**
611 611  
603 +0x(0B F6 1E)   ~/~/ Same as AT+18ALARM=-10,30
612 612  
613 -=== 3.3.4 Set Humidity Alarm Threshold ===
605 +(note: 0x1E= 30, 0xF6 means: 0xF6-0x100 = -10)
614 614  
615 -* (% style="color:blue" %)**AT Command:**
616 616  
617 -(% style="color:#037691" %)**AT+SHHUM=min,max**
608 +(% style="color:#4472c4" %)**2.  Set for Separate Probe:**
618 618  
619 -* When min=0, and max≠0, Alarm higher than max
620 -* When min≠0, and max=0, Alarm lower than min
621 -* When min≠0 and max≠0, Alarm higher than max or lower than min
610 +(% style="color:#037691" %)**AT+18ALARM=min,max,index**
622 622  
623 -Example:
612 +Index:
624 624  
625 - AT+SHHUM=70,0  ~/~/ Alarm when humidity lower than 70%.
614 +* 1: Temperature_Red
615 +* 2: Temperature_White
616 +* 3: Temperature_Black
626 626  
627 -* (% style="color:blue" %)**Downlink Payload:**
618 +**Example:**
628 628  
629 -(% style="color:#037691" %)**0x(0C 02 46 00)**(%%)  ~/~/ Set AT+SHTHUM=70,0
620 + AT+18ALARM=-10,30,1   ~/~/ Alarm when temperature_red < -10 or higher than 30.
630 630  
631 -(% style="color:red" %)**(note: 3^^rd^^ byte= 0x46 for low limit (70%), 4^^th^^ byte = 0x00 for high limit (not set))**
632 632  
623 +* (% style="color:#037691" %)**Downlink Payload:**
633 633  
634 -=== 3.3.5 Set Alarm Interval ===
625 +0x(0B F6 1E 01)   ~/~/ Same as AT+18ALARM=-10,30,1
635 635  
627 +(note: 0x1E= 30, 0xF6 means: 0xF6-0x100 = -10)
628 +
629 +
630 +=== 3.3.4 Set Alarm Interval ===
631 +
632 +
636 636  The shortest time of two Alarm packet. (unit: min)
637 637  
638 -* (% style="color:blue" %)**AT Command:**
635 +* (% style="color:#037691" %)**AT Command:**
639 639  
640 -(% style="color:#037691" %)**AT+ATDC=30** (%%) ~/~/ The shortest interval of two Alarm packets is 30 minutes, Means is there is an alarm packet uplink, there won't be another one in the next 30 minutes.
637 +AT+ATDC=30  ~/~/ The shortest interval of two Alarm packets is 30 minutes, Means is there is an alarm packet uplink, there won't be another one in the next 30 minutes.
641 641  
642 -* (% style="color:blue" %)**Downlink Payload:**
643 643  
644 -(% style="color:#037691" %)**0x(0D 00 1E)**(%%)     **~-~--> ** Set AT+ATDC=0x 00 1E = 30 minutes
640 +* (% style="color:#037691" %)**Downlink Payload:**
645 645  
642 +0x(0D 00 1E)     **~-~-->** Set AT+ATDC=0x 00 1E = 30 minutes
646 646  
647 -=== 3.3.6 Get Alarm settings ===
648 648  
645 +=== 3.3.5 Get Alarm settings  （什么FPORT?） ===
649 649  
647 +
650 650  Send a LoRaWAN downlink to ask device send Alarm settings.
651 651  
652 652  * (% style="color:#037691" %)**Downlink Payload:  **(%%)0x0E 01
... ... @@ -660,7 +660,7 @@
660 660  
661 661  * Alarm & MOD bit is 0x7C, 0x7C >> 2 = 0x31: Means this message is the Alarm settings message.
662 662  
663 -=== 3.3.7 Set Interrupt Mode ===
661 +=== 3.3.6 Set Interrupt Mode ===
664 664  
665 665  
666 666  Feature, Set Interrupt mode for GPIO_EXIT.
... ... @@ -667,8 +667,8 @@
667 667  
668 668  (% style="color:blue" %)**AT Command: AT+INTMOD**
669 669  
670 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
671 -|=(% style="width: 154px;background-color:#D9E2F3" %)**Command Example**|=(% style="width: 196px;background-color:#D9E2F3" %)**Function**|=(% style="width: 157px;background-color:#D9E2F3" %)**Response**
668 +(% border="1" cellspacing="4" style="background-color:#f7faff; color:black; width:510px" %)
669 +|=(% style="width: 154px;" %)**Command Example**|=(% style="width: 196px;" %)**Function**|=(% style="width: 157px;" %)**Response**
672 672  |(% style="width:154px" %)AT+INTMOD=?|(% style="width:196px" %)Show current interrupt mode|(% style="width:157px" %)(((
673 673  0
674 674  OK
... ... @@ -694,65 +694,68 @@
694 694  = 4. Battery & Power Consumption =
695 695  
696 696  
697 -S31x-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
695 +D2x-LB use ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
698 698  
699 699  [[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
700 700  
701 701  
702 -= 5. OTA Firmware update =
700 += 5. OTA firmware update =
703 703  
704 704  
705 -(% class="wikigeneratedid" %)
706 -User can change firmware S31x-LB to:
703 +Please see this link for how to do OTA firmware update: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]
707 707  
708 -* Change Frequency band/ region.
709 -* Update with new features.
710 -* Fix bugs.
711 711  
712 -Firmware and changelog can be downloaded from : **[[Firmware download link>>url:https://www.dropbox.com/sh/kwqv57tp6pejias/AAAopYMATh1GM6fZ-VRCLrpDa?dl=0]]**
706 += 6. FAQ =
713 713  
708 +== 6.1 How to use AT Command via UART to access device? ==
714 714  
715 -Methods to Update Firmware:
716 716  
717 -* (Recommanded way) OTA firmware update via wireless:   [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]
718 -* Update through UART TTL interface.**[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.
711 +See: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]
719 719  
720 -= 6. FAQ =
721 721  
714 +== 6.2 How to update firmware via UART port? ==
722 722  
723 723  
724 -= 7. Order Info =
717 +See: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]
725 725  
726 726  
727 -Part Number: **S31-LB-XX  / S31B-LB-XX**
720 +== 6.3 How to change the LoRa Frequency Bands/Region? ==
728 728  
729 -**XX**: The default frequency band
730 730  
731 -* **AS923**: LoRaWAN AS923 band
723 +Each LoRaWAN frequency bands has different firmware. User can update the device's firmware to the corresponding frequency band to change region.
732 732  
733 -* **AU915**: LoRaWAN AU915 band
734 734  
735 -* **EU433**: LoRaWAN EU433 band
726 += 7. Order Info =
736 736  
737 -* **EU868**: LoRaWAN EU868 band
738 738  
739 -* **KR920**: LoRaWAN KR920 band
729 +Part Number: (% style="color:blue" %)**S31-LB-XX  / S31x-LB-XX**
740 740  
741 -* **US915**: LoRaWAN US915 band
731 +(% style="color:red" %)**XX**(%%): The default frequency band
742 742  
743 -* **IN865**: LoRaWAN IN865 band
733 +* (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band
744 744  
745 -* **CN470**: LoRaWAN CN470 band
735 +* (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band
746 746  
747 -= =
737 +* (% style="color:red" %)**EU433**(%%): LoRaWAN EU433 band
748 748  
739 +* (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band
740 +
741 +* (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band
742 +
743 +* (% style="color:red" %)**US915**(%%): LoRaWAN US915 band
744 +
745 +* (% style="color:red" %)**IN865**(%%): LoRaWAN IN865 band
746 +
747 +* (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
748 +
749 749  = 8. ​Packing Info =
750 750  
751 -**Package Includes**:
752 752  
752 +(% style="color:#037691" %)**Package Includes**:
753 +
753 753  * S31x-LB LoRaWAN Temperature & Humidity Sensor
754 754  
755 -**Dimension and weight**:
756 +(% style="color:#037691" %)**Dimension and weight**:
756 756  
757 757  * Device Size: cm
758 758  
... ... @@ -766,4 +766,5 @@
766 766  
767 767  
768 768  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
769 -* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]
770 +
771 +* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]
1682646494051-944.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -206.9 KB
Content
S31-B.jpg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ellie
Size
... ... @@ -1,1 +1,0 @@
1 -28.3 KB
Content
image-20230421162630-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -23.5 KB
Content
image-20230421171614-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -34.8 KB
Content
image-20230426084152-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -190.0 KB
Content