Skip to Content
Version 76.10 by Xiaoling on 2024/01/17 17:46
Show last authors
1 (% style="display:none" %) (%%) (% style="display:none" %) (%%) (% style="display:none" %)
2
3 (% style="text-align:center" %)
4 [[image:image-20240104162316-6.png]]
5
6
7
8
9
10
11
12 **Table of Contents:**
13
14 {{toc/}}
15
16
17
18
19
20
21 = 1. Introduction =
22
23 == 1.1 What is S31x-LB/LS LoRaWAN Temperature & Humidity Sensor ==
24
25
26 The Dragino S31x-LB/LS is a (% style="color:blue" %)**LoRaWAN Temperature and Humidity Sensor**(%%) for Internet of Things solution. It is used to measure the (% style="color:blue" %)**surrounding environment temperature and relative air humidity precisely**(%%), and then upload to IoT server via LoRaWAN wireless protocol.
27
28 The temperature & humidity sensor used in S31x-LB/LS is SHT31, which is fully calibrated, linearized, and temperature compensated digital output from Sensirion, it provides a strong reliability and long-term stability. The SHT31 is fixed in a (% style="color:blue" %)**waterproof anti-condensation casing**(%%) for long term use.
29
30 The LoRa wireless technology used in S31x-LB/LS allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
31
32 S31x-LB/LS supports (% style="color:blue" %)**Temperature & Humdity alarm feature**(%%), user can set temperature alarm for instant notice. S31x-LB/LS supports Datalog feature, it can save the data when there is no LoRaWAN network and uplink when network recover.
33
34 S31x-LB/LS (% style="color:blue" %)**supports BLE configure**(%%) and (% style="color:blue" %)**wireless OTA update**(%%) which make user easy to use.
35
36 S31x-LB/LS is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%) or (% style="color:blue" %)**solar powered + li-on battery**(%%) it is designed for long term use up to 5 years.
37
38 Each S31x-LB/LS is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
39
40
41 == 1.2 ​Features ==
42
43
44 * LoRaWAN 1.0.3 Class A
45 * Ultra-low power consumption
46 * External 3 meters SHT31 probe (For S31-LB)
47 * Measure range -40°C ~~ 80°C
48 * Temperature & Humidity alarm
49 * Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
50 * Support Bluetooth v5.1 and LoRaWAN remote configure
51 * Support wireless OTA update firmware
52 * Uplink on periodically
53 * Downlink to change configure
54 * 88500mAh Li/SOCl2 Battery (S31/S31B-LB)
55 * Solar panel + 3000mAh Li-on battery (S31/S31B-LS)
56
57 == 1.3 Specification ==
58
59
60 (% style="color:#037691" %)**Common DC Characteristics:**
61
62 * Supply Voltage: Built-in Battery , 2.5v ~~ 3.6v
63 * Operating Temperature: -40 ~~ 85°C
64
65 (% style="color:#037691" %)**Temperature Sensor:**
66
67 * Range: -40 to + 80°C
68 * Accuracy: ±0.2 @ 0-90 °C
69 * Resolution: 0.1°C
70 * Long Term Shift: <0.03 °C/yr
71
72 (% style="color:#037691" %)**Humidity Sensor: **
73
74 * Range: 0 ~~ 99.9% RH
75 * Accuracy: ± 2%RH ( 0 ~~ 100%RH)
76 * Resolution: 0.01% RH
77 * Long Term Shift: <0.25 %RH/yr
78
79 (% style="color:#037691" %)**LoRa Spec:**
80
81 * Frequency Range,  Band 1 (HF): 862 ~~ 1020 Mhz
82 * Max +22 dBm constant RF output vs.
83 * RX sensitivity: down to -139 dBm.
84 * Excellent blocking immunity
85
86 (% style="color:#037691" %)**Battery:**
87
88 * Li/SOCI2 un-chargeable battery
89 * Capacity: 8500mAh
90 * Self-Discharge: <1% / Year @ 25°C
91 * Max continuously current: 130mA
92 * Max boost current: 2A, 1 second
93
94 (% style="color:#037691" %)**Power Consumption**
95
96 * Sleep Mode: 5uA @ 3.3v
97 * LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm
98
99 == 1.4 Sleep mode and working mode ==
100
101
102 (% style="color:blue" %)**Deep Sleep Mode: **(%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.
103
104 (% style="color:blue" %)**Working Mode:** (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.
105
106
107 == 1.5 Button & LEDs ==
108
109
110 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/RS485-LB_Waterproof_RS485UART_to_LoRaWAN_Converter/WebHome/image-20240103160425-4.png?rev=1.1||alt="image-20240103160425-4.png"]]
111
112 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
113 |=(% style="width: 167px;background-color:#4F81BD;color:white" %)**Behavior on ACT**|=(% style="width: 117px;background-color:#4F81BD;color:white" %)**Function**|=(% style="width: 225px;background-color:#4F81BD;color:white" %)**Action**
114 |(% style="width:167px" %)Pressing ACT between 1s < time < 3s|(% style="width:117px" %)Send an uplink|(% style="width:225px" %)(((
115 If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, (% style="color:blue" %)**blue led** (%%)will blink once.
116 Meanwhile, BLE module will be active and user can connect via BLE to configure device.
117 )))
118 |(% style="width:167px" %)Pressing ACT for more than 3s|(% style="width:117px" %)Active Device|(% style="width:225px" %)(((
119 (% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:#037691" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network.
120 (% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.
121 Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device join or not join LoRaWAN network.
122 )))
123 |(% style="width:167px" %)Fast press ACT 5 times.|(% style="width:117px" %)Deactivate Device|(% style="width:225px" %)(% style="color:red" %)**Red led**(%%) will solid on for 5 seconds. Means device is in Deep Sleep Mode.
124
125 == 1.6 BLE connection ==
126
127
128 S31x-LB/LS support BLE remote configure.
129
130
131 BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:
132
133 * Press button to send an uplink
134 * Press button to active device.
135 * Device Power on or reset.
136
137 If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.
138
139
140 == 1.7 Pin Definitions ==
141
142 [[image:http://8.211.40.43/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SN50v3-LB/WebHome/image-20230610163213-1.png?width=699&height=404&rev=1.1||alt="image-20230610163213-1.png"]]
143
144
145 == 1.8 Hardware Variant ==
146
147
148 (% border="1" cellspacing="5" style="width:461.818px" %)
149 |=(% style="width: 102px;background-color:#4F81BD;color:white" %)Model|=(% style="width: 182px; background-color:#4F81BD;color:white" %)Photo|=(% style="width: 176px; background-color:#4F81BD;color:white" %)Probe Info
150 |(% style="width:102px" %)(((
151 S31-LB/LS
152 )))|(% style="width:182px" %)(((
153 (% style="text-align:center" %)
154 [[image:image-20240104165223-7.png]]
155 )))|(% style="width:176px" %)(((
156 1 x SHT31 Probe
157
158 Cable Length : 2 meters
159
160
161 )))
162 |(% style="width:102px" %)(((
163 S31B-LB/LS
164 )))|(% style="width:182px" %)(((
165 (% style="text-align:center" %)
166 [[image:image-20240104165338-9.png]]
167 )))|(% style="width:176px" %)(((
168 1 x SHT31 Probe
169
170 Installed in device.
171 )))
172
173 (% style="display:none" %)
174
175
176
177 == 1.9 Mechanical ==
178
179 === 1.9.1 for LB version ===
180
181 [[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143884058-338.png]]
182
183
184 [[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143899218-599.png]]
185
186
187 [[image:Main.User Manual for LoRaWAN End Nodes.D20-LBD22-LBD23-LB_LoRaWAN_Temperature_Sensor_User_Manual.WebHome@1675143909447-639.png]]
188
189
190 === 1.9.2 for LS version ===
191
192
193 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SN50v3-LB/WebHome/image-20231231203439-3.png?width=886&height=385&rev=1.1||alt="image-20231231203439-3.png"]]
194
195
196 = 2. Configure S31x-LB/LS to connect to LoRaWAN network =
197
198 == 2.1 How it works ==
199
200
201 The S31x-LB/LS is configured as (% style="color:#037691" %)**LoRaWAN OTAA Class A**(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and press the button to activate the S31x-LB/LS. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
202
203
204 == 2.2 ​Quick guide to connect to LoRaWAN server (OTAA) ==
205
206
207 Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.
208
209 The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
210
211
212 (% style="color:blue" %)**Step 1:**(%%) Create a device in TTN with the OTAA keys from S31x-LB/LS.
213
214 Each S31x-LB/LS is shipped with a sticker with the default device EUI as below:
215
216 [[image:image-20230426084152-1.png||alt="图片-20230426084152-1.png" height="233" width="502"]]
217
218
219 You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
220
221
222 (% style="color:blue" %)**Register the device**
223
224 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/1654935135620-998.png?rev=1.1||alt="1654935135620-998.png"]]
225
226
227 (% style="color:blue" %)**Add APP EUI and DEV EUI**
228
229 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-4.png?width=753&height=551&rev=1.1||alt="图片-20220611161308-4.png"]]
230
231
232 (% style="color:blue" %)**Add APP EUI in the application**
233
234
235 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-5.png?width=742&height=601&rev=1.1||alt="图片-20220611161308-5.png"]]
236
237
238 (% style="color:blue" %)**Add APP KEY**
239
240 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LSN50v2-S31-S31B%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20User%20Manual/WebHome/image-20220611161308-6.png?width=744&height=485&rev=1.1||alt="图片-20220611161308-6.png"]]
241
242
243 (% style="color:blue" %)**Step 2:**(%%) Activate on S31x-LB/LS
244
245
246 Press the button for 5 seconds to activate the S31x-LB/LS.
247
248 (% style="color:green" %)**Green led**(%%) will fast blink 5 times, device will enter (% style="color:blue" %)**OTA mode**(%%) for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)**Green led**(%%) will solidly turn on for 5 seconds after joined in network.
249
250 After join success, it will start to upload messages to TTN and you can see the messages in the panel.
251
252
253 == 2.3 ​Uplink Payload ==
254
255 === 2.3.1 Device Status, FPORT~=5 ===
256
257
258 Users can use the downlink command(**0x26 01**) to ask S31x-LB/LS to send device configure detail, include device configure status. S31x-LB/LS will uplink a payload via FPort=5 to server.
259
260 The Payload format is as below.
261
262
263 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
264 |(% colspan="6" style="background-color:#4f81bd; color:white" %)**Device Status (FPORT=5)**
265 |(% style="width:103px" %)**Size (bytes)**|(% style="width:72px" %)**1**|**2**|(% style="width:91px" %)**1**|(% style="width:86px" %)**1**|(% style="width:44px" %)**2**
266 |(% style="width:103px" %)Value|(% style="width:72px" %)Sensor Model|Firmware Version|(% style="width:91px" %)Frequency Band|(% style="width:86px" %)Sub-band|(% style="width:44px" %)BAT
267
268 Example parse in TTNv3
269
270 [[image:image-20230524144422-1.png||height="174" width="1080"]]
271
272
273 (% style="color:#037691" %)**Sensor Model**(%%): For S31x-LB/LS, this value is 0x0A
274
275 (% style="color:#037691" %)**Firmware Version**(%%): 0x0100, Means: v1.0.0 version
276
277 (% style="color:#037691" %)**Frequency Band**:
278
279 0x01: EU868
280
281 0x02: US915
282
283 0x03: IN865
284
285 0x04: AU915
286
287 0x05: KZ865
288
289 0x06: RU864
290
291 0x07: AS923
292
293 0x08: AS923-1
294
295 0x09: AS923-2
296
297 0x0a: AS923-3
298
299 0x0b: CN470
300
301 0x0c: EU433
302
303 0x0d: KR920
304
305 0x0e: MA869
306
307
308 (% style="color:#037691" %)**Sub-Band**:
309
310 AU915 and US915:value 0x00 ~~ 0x08
311
312 CN470: value 0x0B ~~ 0x0C
313
314 Other Bands: Always 0x00
315
316
317 (% style="color:#037691" %)**Battery Info**:
318
319 Check the battery voltage.
320
321 Ex1: 0x0B45 = 2885mV
322
323 Ex2: 0x0B49 = 2889mV
324
325
326 === 2.3.2  Sensor Data. FPORT~=2 ===
327
328
329 Sensor Data is uplink via FPORT=2
330
331 (% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
332 |=(% style="width: 60px;background-color:#4F81BD;color:white" %)(((
333 **Size(bytes)**
334 )))|=(% style="width: 40px;background-color:#4F81BD;color:white" %)2|=(% style="width: 90px;background-color:#4F81BD;color:white" %)4|=(% style="width: 150px; background-color: #4F81BD;color:white" %)1|=(% style="width: 80px; background-color: #4F81BD;color:white" %)**2**|=(% style="width: 80px; background-color: #4F81BD;color:white" %)2
335 |(% style="width:99px" %)Value|(% style="width:69px" %)(((
336 Battery
337 )))|(% style="width:130px" %)(((
338 Unix TimeStamp
339 )))|(% style="width:194px" %)(((
340 Alarm Flag & MOD& Level of PA8
341 )))|(% style="width:106px" %)(((
342 Temperature
343 )))|(% style="width:97px" %)(((
344 Humidity
345 )))
346
347 [[image:image-20230524144456-2.png||height="180" width="1142"]]
348
349
350 ==== (% style="color:#4472c4" %)**Battery**(%%) ====
351
352 Sensor Battery Level.
353
354 Ex1: 0x0B45 = 2885mV
355
356 Ex2: 0x0B49 = 2889mV
357
358
359 ==== (% style="color:#4472c4" %)**Temperature**(%%) ====
360
361 **Example**:
362
363 If payload is: 0105H:  (0105 & 8000 == 0), temp = 0105H /10 = 26.1 degree
364
365 If payload is: FF3FH :  (FF3F & 8000 == 1) , temp = (FF3FH - 65536)/10 = -19.3 degrees.
366
367 (FF3F & 8000：Judge whether the highest bit is 1, when the highest bit is 1, it is negative)
368
369
370 ==== (% style="color:#4472c4" %)**Humidity**(%%) ====
371
372
373 Read:0x(0197)=412    Value:  412 / 10=41.2, So 41.2%
374
375
376 ==== (% style="color:#4472c4" %)**Alarm Flag & MOD & Level of PA8**(%%) ====
377
378
379 **Example:**
380
381 If payload & 0x01 = 0x01  **~-~->** This is an Alarm Message.It means that the temperature and humidity exceed the alarm value or trigger an interrupt.
382
383 If payload & 0x01 = 0x00  **~-~->** This is a normal uplink message, no alarm.
384
385 If payload & 0x80>>7 = 0x01  **~-~->** The PA8 is low level.
386
387 If payload & 0x80>>7 =0x00  **~-~->** The PA8 is high level.
388
389 If payload >> 2 = 0x00  **~-~->**  means MOD=1, This is a sampling uplink message.
390
391 If payload >> 2 = 0x31  **~-~->**  means MOD=31, this message is a reply message for polling, this message contains the alarm settings. see [[this link>>path:#HPolltheAlarmsettings:]] for detail. 
392
393
394 == 2.4 Payload Decoder file ==
395
396
397 In TTN, use can add a custom payload so it shows friendly reading
398
399 In the page (% style="color:#037691" %)**Applications ~-~-> Payload Formats ~-~-> Custom ~-~-> decoder**(%%) to add the decoder from:
400
401 [[https:~~/~~/github.com/dragino/dragino-end-node-decoder/tree/main/S31-LB%26S31B-LB>>https://github.com/dragino/dragino-end-node-decoder/tree/main/S31-LB%26S31B-LB]]
402
403
404 == 2.5 Datalog Feature ==
405
406
407 Datalog Feature is to ensure IoT Server can get all sampling data from Sensor even if the LoRaWAN network is down. For each sampling, S31x-LB/LS will store the reading for future retrieving purposes.
408
409
410 === 2.5.1 Ways to get datalog via LoRaWAN ===
411
412
413 Set PNACKMD=1, S31x-LB/LS will wait for ACK for every uplink, when there is no LoRaWAN network,S31x-LB/LS will mark these records with non-ack messages and store the sensor data, and it will send all messages (10s interval) after the network recovery.
414
415 * (((
416 a) S31x-LB/LS will do an ACK check for data records sending to make sure every data arrive server.
417 )))
418 * (((
419 b) S31x-LB/LS will send data in **CONFIRMED Mode** when PNACKMD=1, but S31x-LB/LS won't re-transmit the packet if it doesn't get ACK, it will just mark it as a NONE-ACK message. In a future uplink if S31x-LB/LS gets a ACK, S31x-LB/LS will consider there is a network connection and resend all NONE-ACK messages.
420 )))
421
422
423
424 === 2.5.2 Unix TimeStamp ===
425
426
427 S31x-LB/LS uses Unix TimeStamp format based on
428
429 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-11.png?width=627&height=97&rev=1.1||alt="图片-20220523001219-11.png" height="97" width="627"]]
430
431 User can get this time from link:  [[https:~~/~~/www.epochconverter.com/>>url:https://www.epochconverter.com/]] :
432
433 Below is the converter example
434
435 [[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/LHT65N%20LoRaWAN%20Temperature%20%26%20Humidity%20Sensor%20Manual/WebHome/image-20220523001219-12.png?width=720&height=298&rev=1.1||alt="图片-20220523001219-12.png" height="298" width="720"]]
436
437
438 So, we can use AT+TIMESTAMP=1611889405 or downlink 3060137afd00 to set the current time 2021 – Jan ~-~- 29 Friday 03:03:25
439
440
441 === 2.5.3 Set Device Time ===
442
443
444 User need to set (% style="color:blue" %)**SYNCMOD=1**(%%) to enable sync time via MAC command.
445
446 Once S31x-LB/LS Joined LoRaWAN network, it will send the MAC command (DeviceTimeReq) and the server will reply with (DeviceTimeAns) to send the current time to S31x-LB/LS. If S31x-LB/LS fails to get the time from the server, S31x-LB/LS will use the internal time and wait for next time request (AT+SYNCTDC to set the time request period, default is 10 days).
447
448 (% style="color:red" %)**Note: LoRaWAN Server need to support LoRaWAN v1.0.3(MAC v1.0.3) or higher to support this MAC command feature, Chirpstack,TTN V3 v3 and loriot support but TTN V3 v2 doesn't support. If server doesn't support this command, it will through away uplink packet with this command, so user will lose the packet with time request for TTN V3 v2 if SYNCMOD=1.**
449
450
451 === 2.5.4 Datalog Uplink payload (FPORT~=3) ===
452
453
454 The Datalog uplinks will use below payload format.
455
456 **Retrieval data payload:**
457
458 (% border="1" cellspacing="5" style="background-color:#f2f2f2; width:500px" %)
459 |=(% style="width: 60px;background-color:#4F81BD;color:white" %)(((
460 **Size(bytes)**
461 )))|=(% style="width: 40px; background-color:#4F81BD;color:white" %)**2**|=(% style="width: 55px; background-color:#4F81BD;color:white" %)**2**|=(% style="width: 65px; background-color:#4F81BD;color:white" %)**2**|=(% style="width: 180px; background-color:#4F81BD;color:white" %)**1**|=(% style="width: 100px; background-color:#4F81BD;color:white" %)**4**
462 |(% style="width:103px" %)Value|(% style="width:68px" %)(((
463 ignore
464 )))|(% style="width:104px" %)(((
465 (((
466 Humidity
467 )))
468 )))|(% style="width:87px" %)(((
469 Temperature
470 )))|(% style="width:178px" %)(((
471 Poll message flag & Alarm Flag& Level of PA8
472 )))|(% style="width:137px" %)Unix Time Stamp
473
474 **Poll message flag & Alarm Flag & Level of PA8:**
475
476 [[image:image-20230524114302-1.png||height="115" width="736"]]
477
478
479 **No ACK Message**:  1: This message means this payload is fromn Uplink Message which doesn't get ACK from the server before ( for **PNACKMD=1** feature)
480
481 **Poll Message Flag**: 1: This message is a poll message reply.
482
483 * Poll Message Flag is set to 1.
484
485 * Each data entry is 11 bytes, to save airtime and battery, devices will send max bytes according to the current DR and Frequency bands.
486
487 For example, in US915 band, the max payload for different DR is:
488
489 **a) DR0:** max is 11 bytes so one entry of data
490
491 **b) DR1:** max is 53 bytes so devices will upload 4 entries of data (total 44 bytes)
492
493 **c) DR2:** total payload includes 11 entries of data
494
495 **d) DR3: **total payload includes 22 entries of data.
496
497 If devise doesn't have any data in the polling time. Device will uplink 11 bytes of 0   
498
499 **Example:**
500
501 If S31x-LB/LS has below data inside Flash:
502
503 [[image:image-20230524114654-2.png]]
504
505
506 If user sends below downlink command: 31646D84E1646D856C05
507
508 Where : Start time: 646D84E1 = time 23/5/24 03:30:41
509
510 Stop time: 646D856C= time 23/5/24 03:33:00
511
512
513 **S31x-LB/LS will uplink this payload.**
514
515 [[image:image-20230524114826-3.png||height="448" width="1244"]]
516
517 (((
518 00 00 02 36 01 10 40 64 6D 84 E1 00 00 02 37 01 10 40 64 6D 84 F8 00 00 02 37 01 0F 40 64 6D 85 04 00 00 02 3A 01 0F 40 64 6D 85 18 00 00 02 3C 01 0F 40 64 6D 85 36 00 00 02 3D 01 0E 40 64 6D 85 3F 00 00 02 3F 01 0E 40 64 6D 85 60 00 00 02 40 01 0E 40 64 6D 85 6A
519 )))
520
521 (((
522 Where the first 11 bytes is for the first entry:
523 )))
524
525 (((
526 00 00 02 36 01 10 40 64 6D 84 E1
527 )))
528
529 (((
530 **Hum**=0x0236/10=56.6
531 )))
532
533 (((
534 **Temp**=0x0110/10=27.2
535 )))
536
537 (((
538 **poll message flag & Alarm Flag & Level of PA8**=0x40,means reply data,sampling uplink message,the PA8 is low level.
539 )))
540
541 (((
542 **Unix time** is 0x646D84E1=1684899041s=23/5/24 03:30:41
543 )))
544
545
546 (% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的(% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" data-widget="image" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220, 220, 220, 0.5); display:none" tabindex="-1" %)[[image:data:image/gif;base64,R0lGODlhAQABAPABAP///wAAACH5BAEKAAAALAAAAAABAAEAAAICRAEAOw==||alt="数据 URI 图片" draggable="true" height="15" role="presentation" title="单击并拖动以移动" width="15"]](% aria-label="数据 URI 图像图像小部件" contenteditable="false" role="region" style="background-image:url(http://wiki1.dragino.com/xwiki/webjars/wiki%3Axwiki/application-ckeditor-webjar/1.61/plugins/widget/images/handle.png); background:rgba(220,220,220,0.5); display:none" tabindex="-1" title="单击并拖动以调整大小" %)的
547
548 == 2.6 Temperature Alarm Feature ==
549
550
551 S31x-LB/LS work flow with Alarm feature.
552
553
554 [[image:image-20230524110125-3.png||height="768" width="1115"]]
555
556
557
558 == 2.7 Frequency Plans ==
559
560
561 The S31x-LB/LS uses OTAA mode and below frequency plans by default. Each frequency band use different firmware, user update the firmware to the corresponding band for their country.
562
563 [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]
564
565
566 == 2.8 ​Firmware Change Log ==
567
568
569 **Firmware download link: **[[https:~~/~~/www.dropbox.com/sh/fis3g6nmhv0eokg/AAC6BcCZaX4BdqZkduUvZ3jIa?dl=0>>https://www.dropbox.com/sh/fis3g6nmhv0eokg/AAC6BcCZaX4BdqZkduUvZ3jIa?dl=0]]
570
571
572 = 3. Configure S31x-LB/LS =
573
574 == 3.1 Configure Methods ==
575
576
577 S31x-LB/LS supports below configure method:
578
579 * AT Command via Bluetooth Connection (**Recommended**): [[BLE Configure Instruction>>http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
580 * AT Command via UART Connection : See [[UART Connection>>http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H2.3UARTConnectionforSN50v3basemotherboard]].
581 * LoRaWAN Downlink.  Instruction for different platforms: See [[IoT LoRaWAN Server>>http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
582
583 == 3.2 General Commands ==
584
585
586 These commands are to configure:
587
588 * General system settings like: uplink interval.
589 * LoRaWAN protocol & radio related command.
590
591 They are same for all Dragino Devices which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:
592
593 [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
594
595
596 == 3.3 Commands special design for S31x-LB/LS ==
597
598
599 These commands only valid for S31x-LB/LS, as below:
600
601
602 === 3.3.1 Set Transmit Interval Time ===
603
604
605 Feature: Change LoRaWAN End Node Transmit Interval.
606
607 (% style="color:blue" %)**AT Command: AT+TDC**
608
609 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
610 |=(% style="width: 156px;background-color:#4F81BD;color:white" %)**Command Example**|=(% style="width: 137px;background-color:#4F81BD;color:white" %)**Function**|=(% style="background-color:#4F81BD;color:white" %)**Response**
611 |(% style="width:156px" %)AT+TDC=?|(% style="width:137px" %)Show current transmit Interval|(((
612 30000
613 OK
614 the interval is 30000ms = 30s
615 )))
616 |(% style="width:156px" %)AT+TDC=60000|(% style="width:137px" %)Set Transmit Interval|(((
617 OK
618 Set transmit interval to 60000ms = 60 seconds
619 )))
620
621 (% style="color:blue" %)**Downlink Command: 0x01**
622
623 Format: Command Code (0x01) followed by 3 bytes time value.
624
625 If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
626
627 * Example 1: Downlink Payload: 0100001E  ~/~/  Set Transmit Interval (TDC) = 30 seconds
628 * Example 2: Downlink Payload: 0100003C  ~/~/  Set Transmit Interval (TDC) = 60 seconds
629
630 === 3.3.2 Get Device Status ===
631
632
633 Send a LoRaWAN downlink to ask device send Alarm settings.
634
635 (% style="color:blue" %)**Downlink Payload:  **(%%)0x26 01
636
637 Sensor will upload Device Status via FPORT=5. See payload section for detail.
638
639
640 === 3.3.3 Set Temperature Alarm Threshold ===
641
642
643 * (% style="color:blue" %)**AT Command:**
644
645 (% style="color:#037691" %)**AT+SHTEMP=min,max**
646
647 * When min=0, and max≠0, Alarm higher than max
648 * When min≠0, and max=0, Alarm lower than min
649 * When min≠0 and max≠0, Alarm higher than max or lower than min
650
651 Example:
652
653 AT+SHTEMP=0,30   ~/~/ Alarm when temperature higher than 30.
654
655 * (% style="color:blue" %)**Downlink Payload:**
656
657 (% style="color:#037691" %)**0x(0C 01 00 1E)**  (%%) ~/~/ Set AT+SHTEMP=0,30
658
659 (% style="color:red" %)**(note: 3^^rd^^ byte= 0x00 for low limit(not set), 4^^th^^ byte = 0x1E for high limit: 30)**
660
661
662 === 3.3.4 Set Humidity Alarm Threshold ===
663
664
665 * (% style="color:blue" %)**AT Command:**
666
667 (% style="color:#037691" %)**AT+SHHUM=min,max**
668
669 * When min=0, and max≠0, Alarm higher than max
670 * When min≠0, and max=0, Alarm lower than min
671 * When min≠0 and max≠0, Alarm higher than max or lower than min
672
673 Example:
674
675 AT+SHHUM=70,0  ~/~/ Alarm when humidity lower than 70%.
676
677 * (% style="color:blue" %)**Downlink Payload:**
678
679 (% style="color:#037691" %)**0x(0C 02 46 00)**(%%)  ~/~/ Set AT+SHTHUM=70,0
680
681 (% style="color:red" %)**(note: 3^^rd^^ byte= 0x46 for low limit (70%), 4^^th^^ byte = 0x00 for high limit (not set))**
682
683
684 === 3.3.5 Set Alarm Interval ===
685
686
687 The shortest time of two Alarm packet. (unit: min)
688
689 * (% style="color:blue" %)**AT Command:**
690
691 (% style="color:#037691" %)**AT+ATDC=30** (%%) ~/~/ The shortest interval of two Alarm packets is 30 minutes, Means is there is an alarm packet uplink, there won't be another one in the next 30 minutes.
692
693 * (% style="color:blue" %)**Downlink Payload:**
694
695 (% style="color:#037691" %)**0x(0D 00 1E)**(%%)     **~-~--> ** Set AT+ATDC=0x 00 1E = 30 minutes
696
697
698 === 3.3.6 Get Alarm settings ===
699
700
701 Send a LoRaWAN downlink to ask device send Alarm settings.
702
703 * (% style="color:#037691" %)**Downlink Payload:  **(%%)0x0E 01
704
705 **Example:**
706
707 [[image:image-20230524110211-4.png]]
708
709 **Explain:**
710
711 * Alarm & MOD bit is 0x7C, 0x7C >> 2 = 0x31: Means this message is the Alarm settings message.
712
713 === 3.3.7 Set Interrupt Mode ===
714
715
716 Feature, Set Interrupt mode for PA8 of pin.
717
718 When AT+INTMOD=0 is set, PA8 is used as a digital input port.
719
720 (% style="color:blue" %)**AT Command: AT+INTMOD**
721
722 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
723 |=(% style="width: 155px;background-color:#4F81BD;color:white" %)**Command Example**|=(% style="width: 197px;background-color:#4F81BD;color:white" %)**Function**|=(% style="width: 158px;background-color:#4F81BD;color:white" %)**Response**
724 |(% style="width:154px" %)AT+INTMOD=?|(% style="width:196px" %)Show current interrupt mode|(% style="width:157px" %)(((
725 0
726 OK
727 the mode is 0 =Disable Interrupt
728 )))
729 |(% style="width:154px" %)AT+INTMOD=2|(% style="width:196px" %)(((
730 Set Transmit Interval
731 0. (Disable Interrupt),
732 ~1. (Trigger by rising and falling edge)
733 2. (Trigger by falling edge)
734 3. (Trigger by rising edge)
735 )))|(% style="width:157px" %)OK
736
737 (% style="color:blue" %)**Downlink Command: 0x06**
738
739 Format: Command Code (0x06) followed by 3 bytes.
740
741 This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
742
743 * Example 1: Downlink Payload: 06000000  ~/~/  Turn off interrupt mode
744 * Example 2: Downlink Payload: 06000003  ~/~/  Set the interrupt mode to rising edge trigger
745
746 === 3.3.8 Set Power Output Duration ===
747
748
749 Control the output duration 5V . Before each sampling, device will
750
751 ~1. first enable the power output to external sensor,
752
753 2. keep it on as per duration, read sensor value and construct uplink payload
754
755 3. final, close the power output.
756
757 (% style="color:blue" %)**AT Command: AT+5VT**
758
759 (% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
760 |=(% style="width: 155px;background-color:#4F81BD;color:white" %)**Command Example**|=(% style="width: 197px;background-color:#4F81BD;color:white" %)**Function**|=(% style="width: 158px;background-color:#4F81BD;color:white" %)**Response**
761 |(% style="width:154px" %)AT+5VT=?|(% style="width:196px" %)Show 5V open time.|(% style="width:157px" %)0 (default)
762 OK
763 |(% style="width:154px" %)AT+5VT=1000|(% style="width:196px" %)Close after a delay of 1000 milliseconds.|(% style="width:157px" %)OK
764
765 (% style="color:blue" %)**Downlink Command: 0x07**
766
767 Format: Command Code (0x07) followed by 2 bytes.
768
769 The first and second bytes are the time to turn on.
770
771 * Example 1: Downlink Payload: 070000  **~-~-->**  AT+5VT=0
772 * Example 2: Downlink Payload: 0701F4  **~-~-->**  AT+5VT=500
773
774 = 4. Battery & Power Consumption =
775
776
777 S31x-LB use ER26500 + SPC1520 battery pack and S31x-LS use 3000mAh Recharable Battery with Solar Panel. See below link for detail information about the battery info and how to replace.
778
779 [[**Battery Info & Power Consumption Analyze**>>http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
780
781
782 = 5. OTA Firmware update =
783
784
785 (% class="wikigeneratedid" %)
786 User can change firmware S31x-LB/LS to:
787
788 * Change Frequency band/ region.
789 * Update with new features.
790 * Fix bugs.
791
792 Firmware and changelog can be downloaded from : **[[Firmware download link>>https://www.dropbox.com/sh/fis3g6nmhv0eokg/AAC6BcCZaX4BdqZkduUvZ3jIa?dl=0]]**
793
794
795 Methods to Update Firmware:
796
797 * (Recommanded way) OTA firmware update via wireless : **[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]**
798 * Update through UART TTL interface : **[[Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]**.
799
800 = 6. FAQ =
801
802
803
804 = 7. Order Info =
805
806
807 Part Number: (% style="color:blue" %)**S31-LB-XX / S31B-LB-XX**(%%)**  or  (% style="color:blue" %)S31-LS-XX / S31B-LS-XX(%%)**
808
809 (% style="color:red" %)**XX**(%%): The default frequency band
810
811 * (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band
812
813 * (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band
814
815 * (% style="color:red" %)**EU433**(%%): LoRaWAN EU433 band
816
817 * (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band
818
819 * (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band
820
821 * (% style="color:red" %)**US915**(%%): LoRaWAN US915 band
822
823 * (% style="color:red" %)**IN865**(%%): LoRaWAN IN865 band
824
825 * (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
826
827 = 8. ​Packing Info =
828
829
830 (% style="color:#037691" %)**Package Includes**:
831
832 * S31x-LB or S31x-LS LoRaWAN Temperature & Humidity Sensor
833
834 (% style="color:#037691" %)**Dimension and weight**:
835
836 * Device Size: cm
837
838 * Device Weight: g
839
840 * Package Size / pcs : cm
841
842 * Weight / pcs : g
843
844 = 9. Support =
845
846
847 * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
848
849 * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[Support@dragino.cc>>mailto:Support@dragino.cc]].