Wiki source code of PS-LB/LS -- LoRaWAN Air Water Pressure Sensor User Manual

Version 88.1 by Mengting Qiu on 2024/05/13 10:29

version	line-number	content
70.2	1
6.2	2
	3
70.3	4	(% style="text-align:center" %)
70.4	5	[[image:image-20240109154731-4.png\|\|height="671" width="945"]]
6.2	6
66.2	7
	8
70.3	9
	10
	11
	12
70.4	13	Table of Contents :
70.3	14
42.4	15	{{toc/}}
6.2	16
	17
	18
42.5	19
	20
	21
16.2	22	= 1. Introduction =
6.2	23
9.2	24	== 1.1 What is LoRaWAN Pressure Sensor ==
	25
	26
42.31	27	(((
72.7	28	The Dragino PS-LB/LS series sensors are (% style="color:blue" %)LoRaWAN Pressure Sensor(%%) for Internet of Things solution. PS-LB/LS can measure Air, Water pressure and liquid level and upload the sensor data via wireless to LoRaWAN IoT server.
42.31	29	)))
6.2	30
42.31	31	(((
72.7	32	The PS-LB/LS series sensors include (% style="color:blue" %)Thread Installation Type(%%) and (% style="color:blue" %)Immersion Type(%%), it supports different pressure range which can be used for different measurement requirement.
42.31	33	)))
6.2	34
42.31	35	(((
72.7	36	The LoRa wireless technology used in PS-LB/LS allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
42.31	37	)))
6.2	38
42.31	39	(((
72.7	40	PS-LB/LS supports BLE configure and wireless OTA update which make user easy to use.
42.31	41	)))
6.2	42
42.31	43	(((
72.7	44	PS-LB/LS is powered by (% style="color:blue" %)8500mAh Li-SOCI2 battery (%%)or (% style="color:blue" %)solar powered + li-on battery (%%), it is designed for long term use up to 5 years.
42.31	45	)))
6.2	46
42.31	47	(((
72.7	48	Each PS-LB/LS is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
42.31	49	)))
6.2	50
9.2	51	[[image:1675071321348-194.png]]
6.2	52
	53
9.2	54	== 1.2 Features ==
6.2	55
	56
	57	* LoRaWAN 1.0.3 Class A
	58	* Ultra-low power consumption
	59	* Measure air / gas or water pressure
	60	* Different pressure range available
	61	* Thread Installation Type or Immersion Type
	62	* Monitor Battery Level
	63	* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
	64	* Support Bluetooth v5.1 and LoRaWAN remote configure
	65	* Support wireless OTA update firmware
	66	* Uplink on periodically
	67	* Downlink to change configure
47.1	68	* Controllable 3.3v,5v and 12v output to power external sensor
70.6	69	* 8500mAh Li/SOCl2 Battery (PS-LB)
	70	* Solar panel + 3000mAh Li-on battery (PS-LS)
6.2	71
9.2	72	== 1.3 Specification ==
	73
	74
42.17	75	(% style="color:#037691" %)Micro Controller:
6.2	76
	77	* MCU: 48Mhz ARM
	78	* Flash: 256KB
	79	* RAM: 64KB
	80
42.17	81	(% style="color:#037691" %)Common DC Characteristics:
6.2	82
72.5	83	* Supply Voltage: Built-in Battery , 2.5v ~~ 3.6v
6.2	84	* Operating Temperature: -40 ~~ 85°C
	85
42.17	86	(% style="color:#037691" %)LoRa Spec:
6.2	87
57.1	88	* Frequency Range, Band 1 (HF): 862 ~~ 1020 Mhz,Band 2 (LF): 410 ~~ 528 Mhz
6.2	89	* Max +22 dBm constant RF output vs.
	90	* RX sensitivity: down to -139 dBm.
	91	* Excellent blocking immunity
	92
42.17	93	(% style="color:#037691" %)Current Input Measuring :
6.2	94
	95	* Range: 0 ~~ 20mA
	96	* Accuracy: 0.02mA
	97	* Resolution: 0.001mA
	98
42.17	99	(% style="color:#037691" %)Voltage Input Measuring:
6.2	100
	101	* Range: 0 ~~ 30v
	102	* Accuracy: 0.02v
	103	* Resolution: 0.001v
	104
42.17	105	(% style="color:#037691" %)Battery:
6.2	106
	107	* Li/SOCI2 un-chargeable battery
	108	* Capacity: 8500mAh
	109	* Self-Discharge: <1% / Year @ 25°C
	110	* Max continuously current: 130mA
	111	* Max boost current: 2A, 1 second
	112
42.17	113	(% style="color:#037691" %)Power Consumption
6.2	114
	115	* Sleep Mode: 5uA @ 3.3v
	116	* LoRa Transmit Mode: 125mA @ 20dBm, 82mA @ 14dBm
	117
9.2	118	== 1.4 Probe Types ==
6.2	119
9.2	120	=== 1.4.1 Thread Installation Type ===
6.2	121
	122
9.2	123	[[image:1675071448299-229.png]]
6.2	124
9.2	125	* Hersman Pressure Transmitter
	126	* Measuring Range: -0.1 ~~ 0 ~~ 60MPa, see order info.
	127	* Accuracy: 0.2% F.S
	128	* Long-Term Stability: 0.2% F.S ±0.05%
	129	* Overload 200% F.S
	130	* Zero Temperature Drift: 0.03% FS/℃(≤100Kpa), 0.02%FS/℃(＞100Kpa)
	131	* FS Temperature Drift: 0.003% FS/℃(≤100Kpa), 0.002%FS/℃(＞100Kpa)
	132	* Storage temperature: -30℃~~80℃
	133	* Operating temperature: -20℃~~60℃
	134	* Connector Type: Various Types, see order info
6.2	135
9.2	136	=== 1.4.2 Immersion Type ===
6.2	137
	138
71.2	139	[[image:image-20240109160445-5.png\|\|height="284" width="214"]]
9.2	140
	141	* Immersion Type, Probe IP Level: IP68
	142	* Measuring Range: Measure range can be customized, up to 100m.
	143	* Accuracy: 0.2% F.S
	144	* Long-Term Stability: ±0.2% F.S / Year
	145	* Storage temperature: -30℃~~80℃
51.1	146	* Operating temperature: 0℃~~50℃
9.2	147	* Material: 316 stainless steels
	148
80.1	149	=== 1.4.3 Wireless Differential Air Pressure Sensor ===
	150
	151	[[image:image-20240511174954-1.png]]
	152
	153	* Measuring Range: -100KPa~~0~~100KPa,Intermediate range is optional.
	154	* Accuracy: 0.5% F.S, resolution is 0.05%.
	155	* Overload: 300% F.S
	156	* Zero temperature drift: ±0.03%F.S/°C
	157	* Operating temperature: -40℃~~85℃
	158	* Compensation temperature: 0~~50°C
	159
	160
72.4	161	== 1.5 Application and Installation ==
13.2	162
72.4	163	=== 1.5.1 Thread Installation Type ===
13.2	164
	165
42.17	166	(% style="color:blue" %)Application:
6.2	167
	168	* Hydraulic Pressure
	169	* Petrochemical Industry
	170	* Health and Medical
	171	* Food & Beverage Processing
	172	* Auto-controlling house
	173	* Constant Pressure Water Supply
	174	* Liquid Pressure measuring
	175
	176	Order the suitable thread size and install to measure the air / liquid pressure
	177
13.2	178	[[image:1675071670469-145.png]]
6.2	179
	180
72.4	181	=== 1.5.2 Immersion Type ===
6.2	182
	183
42.17	184	(% style="color:blue" %)Application:
6.2	185
	186	Liquid & Water Pressure / Level detect.
	187
13.2	188	[[image:1675071725288-579.png]]
6.2	189
	190
	191	The Immersion Type pressure sensor is shipped with the probe and device separately. When user got the device, below is the wiring to for connect the probe to the device.
	192
74.1	193	The Immersion Type Sensor has different variant which defined by Ixx. For example, this means two points:
6.2	194
74.1	195	* Cable Length: 10 Meters
	196	* Water Detect Range: 0 ~~ 10 Meters.
	197
13.2	198	[[image:1675071736646-450.png]]
6.2	199
	200
13.2	201	[[image:1675071776102-240.png]]
6.2	202
	203
88.1	204
	205	=== 1.5.3 Wireless Differential Air Pressure Sensor ===
	206
	207
	208	(% style="color:blue" %)Application:
	209
	210	Indoor Air Control & Filter clogging Detect.
	211
	212	[[image:image-20240513100129-6.png]]
	213
	214	[[image:image-20240513100135-7.png]]
	215
	216
	217	The Wireless Differential Air Pressure Sensor is shipped with the probe and device separately. When user got the device, below is the wiring to for connect the probe to the device.
	218
	219	[[image:image-20240513093957-1.png]]
	220
	221
	222	Size of wind pressure transmitter:
	223
	224	[[image:image-20240513094047-2.png]]
	225
	226	Note: The above dimensions are measured by hand, and the numerical error of the shell is within ±0.2mm.
	227
	228
	229
	230
	231
72.4	232	== 1.6 Sleep mode and working mode ==
6.2	233
	234
42.17	235	(% style="color:blue" %)Deep Sleep Mode: (%%)Sensor doesn't have any LoRaWAN activate. This mode is used for storage and shipping to save battery life.
6.2	236
42.17	237	(% style="color:blue" %)Working Mode: (%%)In this mode, Sensor will work as LoRaWAN Sensor to Join LoRaWAN network and send out sensor data to server. Between each sampling/tx/rx periodically, sensor will be in IDLE mode), in IDLE mode, sensor has the same power consumption as Deep Sleep mode.
6.2	238
	239
72.4	240	== 1.7 Button & LEDs ==
6.2	241
	242
71.2	243	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/RS485-LB_Waterproof_RS485UART_to_LoRaWAN_Converter/WebHome/image-20240103160425-4.png?rev=1.1\|\|alt="image-20240103160425-4.png"]](% style="display:none" %)
6.2	244
53.28	245	(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
72.15	246	\|=(% style="width: 167px;background-color:#4F81BD;color:white" %)Behavior on ACT\|=(% style="width: 117px;background-color:#4F81BD;color:white" %)Function\|=(% style="width: 226px;background-color:#4F81BD;color:white" %)Action
53.2	247	\|(% style="background-color:#f2f2f2; width:167px" %)Pressing ACT between 1s < time < 3s\|(% style="background-color:#f2f2f2; width:117px" %)Send an uplink\|(% style="background-color:#f2f2f2; width:225px" %)(((
42.17	248	If sensor is already Joined to LoRaWAN network, sensor will send an uplink packet, (% style="color:blue" %)blue led (%%)will blink once.
6.2	249	Meanwhile, BLE module will be active and user can connect via BLE to configure device.
	250	)))
53.2	251	\|(% style="background-color:#f2f2f2; width:167px" %)Pressing ACT for more than 3s\|(% style="background-color:#f2f2f2; width:117px" %)Active Device\|(% style="background-color:#f2f2f2; width:225px" %)(((
	252	(% style="background-color:#f2f2f2; color:green" %)Green led(%%) will fast blink 5 times, device will enter (% style="color:#037691" %)OTA mode(%%) for 3 seconds. And then start to JOIN LoRaWAN network.
	253	(% style="background-color:#f2f2f2; color:green" %)Green led(%%) will solidly turn on for 5 seconds after joined in network.
6.2	254	Once sensor is active, BLE module will be active and user can connect via BLE to configure device, no matter if device join or not join LoRaWAN network.
	255	)))
62.8	256	\|(% style="background-color:#f2f2f2; width:167px" %)Fast press ACT 5 times.\|(% style="background-color:#f2f2f2; width:117px" %)Deactivate Device\|(% style="background-color:#f2f2f2; width:225px" %)(% style="color:red" %)Red led(%%) will solid on for 5 seconds. Means PS-LB is in Deep Sleep Mode.
6.2	257
72.4	258	== 1.8 Pin Mapping ==
6.2	259
	260
15.2	261	[[image:1675072568006-274.png]]
6.2	262
	263
72.4	264	== 1.9 BLE connection ==
6.2	265
	266
72.7	267	PS-LB/LS support BLE remote configure.
6.2	268
	269
	270	BLE can be used to configure the parameter of sensor or see the console output from sensor. BLE will be only activate on below case:
	271
	272	* Press button to send an uplink
	273	* Press button to active device.
	274	* Device Power on or reset.
	275
	276	If there is no activity connection on BLE in 60 seconds, sensor will shut down BLE module to enter low power mode.
	277
	278
72.4	279	== 1.10 Mechanical ==
6.2	280
72.4	281	=== 1.10.1 for LB version(% style="display:none" %) (%%) ===
6.2	282
	283
72.2	284	[[image:image-20240109160800-6.png]]
6.2	285
	286
72.4	287	=== 1.10.2 for LS version ===
6.2	288
72.2	289
	290	[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/SN50v3-LB/WebHome/image-20231231203439-3.png?width=886&height=385&rev=1.1\|\|alt="image-20231231203439-3.png"]]
	291
	292
72.8	293	= 2. Configure PS-LB/LS to connect to LoRaWAN network =
26.2	294
	295	== 2.1 How it works ==
	296
	297
72.8	298	The PS-LB/LS is configured as (% style="color:#037691" %)LoRaWAN OTAA Class A(%%) mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and activate the PS-LB/LS. It will automatically join the network via OTAA and start to send the sensor value. The default uplink interval is 20 minutes.
6.2	299
	300
26.2	301	== 2.2 Quick guide to connect to LoRaWAN server (OTAA) ==
	302
	303
6.2	304	Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LPS8v2>>url:https://www.dragino.com/products/lora-lorawan-gateway/item/228-lps8v2.html]] as a LoRaWAN gateway in this example.
	305
	306
26.2	307	[[image:1675144005218-297.png]]
6.2	308
	309
	310	The LPS8V2 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
	311
	312
72.8	313	(% style="color:blue" %)Step 1:(%%) Create a device in TTN with the OTAA keys from PS-LB/LS.
6.2	314
72.8	315	Each PS-LB/LS is shipped with a sticker with the default device EUI as below:
6.2	316
54.3	317	[[image:image-20230426085320-1.png\|\|height="234" width="504"]]
6.2	318
	319
	320	You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
	321
	322
42.17	323	(% style="color:blue" %)Register the device
6.2	324
26.2	325	[[image:1675144099263-405.png]]
6.2	326
	327
42.17	328	(% style="color:blue" %)Add APP EUI and DEV EUI
6.2	329
26.2	330	[[image:1675144117571-832.png]]
6.2	331
	332
42.17	333	(% style="color:blue" %)Add APP EUI in the application
6.2	334
	335
26.2	336	[[image:1675144143021-195.png]]
6.2	337
	338
42.17	339	(% style="color:blue" %)Add APP KEY
6.2	340
26.2	341	[[image:1675144157838-392.png]]
6.2	342
72.8	343	(% style="color:blue" %)Step 2:(%%) Activate on PS-LB/LS
6.2	344
	345
72.8	346	Press the button for 5 seconds to activate the PS-LB/LS.
6.2	347
42.17	348	(% style="color:green" %)Green led(%%) will fast blink 5 times, device will enter (% style="color:blue" %)OTA mode(%%) for 3 seconds. And then start to JOIN LoRaWAN network. (% style="color:green" %)Green led(%%) will solidly turn on for 5 seconds after joined in network.
6.2	349
	350	After join success, it will start to upload messages to TTN and you can see the messages in the panel.
	351
	352
27.2	353	== 2.3 Uplink Payload ==
6.2	354
27.2	355	=== 2.3.1 Device Status, FPORT~=5 ===
6.2	356
	357
72.8	358	Include device configure status. Once PS-LB/LS Joined the network, it will uplink this message to the server.
6.2	359
72.8	360	Users can also use the downlink command(0x26 01) to ask PS-LB/LS to resend this uplink.
6.2	361
	362
53.28	363	(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
73.2	364	\|(% colspan="6" style="background-color:#4f81bd; color:white" %)Device Status (FPORT=5)
53.3	365	\|(% style="background-color:#f2f2f2; width:103px" %)Size (bytes)\|(% style="background-color:#f2f2f2; width:72px" %)1\|(% style="background-color:#f2f2f2" %)2\|(% style="background-color:#f2f2f2; width:91px" %)1\|(% style="background-color:#f2f2f2; width:86px" %)1\|(% style="background-color:#f2f2f2; width:44px" %)2
	366	\|(% style="background-color:#f2f2f2; width:103px" %)Value\|(% style="background-color:#f2f2f2; width:72px" %)Sensor Model\|(% style="background-color:#f2f2f2" %)Firmware Version\|(% style="background-color:#f2f2f2; width:91px" %)Frequency Band\|(% style="background-color:#f2f2f2; width:86px" %)Sub-band\|(% style="background-color:#f2f2f2; width:44px" %)BAT
6.2	367
	368	Example parse in TTNv3
	369
27.2	370	[[image:1675144504430-490.png]]
6.2	371
	372
72.8	373	(% style="color:#037691" %)Sensor Model(%%): For PS-LB/LS, this value is 0x16
6.2	374
42.17	375	(% style="color:#037691" %)Firmware Version(%%): 0x0100, Means: v1.0.0 version
6.2	376
42.17	377	(% style="color:#037691" %)Frequency Band:
6.2	378
	379	*0x01: EU868
	380
	381	*0x02: US915
	382
	383	*0x03: IN865
	384
	385	*0x04: AU915
	386
	387	*0x05: KZ865
	388
	389	*0x06: RU864
	390
	391	*0x07: AS923
	392
	393	*0x08: AS923-1
	394
	395	*0x09: AS923-2
	396
	397	*0x0a: AS923-3
	398
	399	*0x0b: CN470
	400
	401	*0x0c: EU433
	402
	403	*0x0d: KR920
	404
	405	*0x0e: MA869
	406
	407
42.17	408	(% style="color:#037691" %)Sub-Band:
6.2	409
	410	AU915 and US915:value 0x00 ~~ 0x08
	411
	412	CN470: value 0x0B ~~ 0x0C
	413
	414	Other Bands: Always 0x00
	415
	416
42.17	417	(% style="color:#037691" %)Battery Info:
6.2	418
	419	Check the battery voltage.
	420
	421	Ex1: 0x0B45 = 2885mV
	422
	423	Ex2: 0x0B49 = 2889mV
	424
	425
42.11	426	=== 2.3.2 Sensor value, FPORT~=2 ===
6.2	427
	428
	429	Uplink payload includes in total 9 bytes.
	430
	431
53.4	432	(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
73.2	433	\|(% style="background-color:#4f81bd; color:white; width:97px" %)(((
37.2	434	Size(bytes)
73.2	435	)))\|(% style="background-color:#4f81bd; color:white; width:48px" %)2\|(% style="background-color:#4f81bd; color:white; width:71px" %)2\|(% style="background-color:#4f81bd; color:white; width:98px" %)2\|(% style="background-color:#4f81bd; color:white; width:73px" %)2\|(% style="background-color:#4f81bd; color:white; width:122px" %)1
60.4	436	\|(% style="width:97px" %)Value\|(% style="width:48px" %)[[BAT>>\|\|anchor="H2.3.3BatteryInfo"]]\|(% style="width:71px" %)[[Probe Model>>\|\|anchor="H2.3.4ProbeModel"]]\|(% style="width:98px" %)[[0 ~~~~ 20mA value>>\|\|anchor="H2.3.507E20mAvalue28IDC_IN29"]]\|(% style="width:73px" %)[[0 ~~~~ 30v value>>\|\|anchor="H2.3.607E30Vvalue28pinVDC_IN29"]]\|(% style="width:122px" %)[[IN1 &IN2 Interrupt flag>>\|\|anchor="H2.3.7IN126IN226INTpin"]]
6.2	437
37.2	438	[[image:1675144608950-310.png]]
6.2	439
	440
47.1	441	=== 2.3.3 Battery Info ===
45.1	442
	443
72.8	444	Check the battery voltage for PS-LB/LS.
6.2	445
	446	Ex1: 0x0B45 = 2885mV
	447
	448	Ex2: 0x0B49 = 2889mV
	449
	450
47.1	451	=== 2.3.4 Probe Model ===
45.1	452
6.2	453
72.8	454	PS-LB/LS has different kind of probe, 4~~20mA represent the full scale of the measuring range. So a 12mA output means different meaning for different probe.
6.2	455
	456
53.6	457	For example.
6.2	458
53.28	459	(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
73.2	460	\|(% style="background-color:#4f81bd; color:white" %)Part Number\|(% style="background-color:#4f81bd; color:white" %)Probe Used\|(% style="background-color:#4f81bd; color:white" %)4~~20mA scale\|(% style="background-color:#4f81bd; color:white" %)Example: 12mA meaning
72.8	461	\|(% style="background-color:#f2f2f2" %)PS-LB/LS-I3\|(% style="background-color:#f2f2f2" %)immersion type with 3 meters cable\|(% style="background-color:#f2f2f2" %)0~~3 meters\|(% style="background-color:#f2f2f2" %)1.5 meters pure water
	462	\|(% style="background-color:#f2f2f2" %)PS-LB/LS-I5\|(% style="background-color:#f2f2f2" %)immersion type with 5 meters cable\|(% style="background-color:#f2f2f2" %)0~~5 meters\|(% style="background-color:#f2f2f2" %)2.5 meters pure water
	463	\|(% style="background-color:#f2f2f2" %)PS-LB/LS-T20-B\|(% style="background-color:#f2f2f2" %)T20 threaded probe\|(% style="background-color:#f2f2f2" %)0~~1MPa\|(% style="background-color:#f2f2f2" %)0.5MPa air / gas or water pressure
6.2	464
47.1	465	The probe model field provides the convenient for server to identical how it should parse the 4~~20mA sensor value and get the correct value.
6.2	466
	467
47.1	468	=== 2.3.5 0~~20mA value (IDC_IN) ===
37.2	469
47.1	470
50.1	471	The output value from Pressure Probe, use together with Probe Model to get the pressure value or water level.
6.2	472
42.17	473	(% style="color:#037691" %)Example:
6.2	474
	475	27AE(H) = 10158 (D)/1000 = 10.158mA.
	476
	477
50.1	478	Instead of pressure probe, User can also connect a general 4~~20mA in this port to support different types of 4~~20mA sensors. below is the connection example:
	479
	480	[[image:image-20230225154759-1.png\|\|height="408" width="741"]]
	481
	482
47.1	483	=== 2.3.6 0~~30V value ( pin VDC_IN) ===
6.2	484
37.2	485
6.2	486	Measure the voltage value. The range is 0 to 30V.
	487
42.17	488	(% style="color:#037691" %)Example:
6.2	489
	490	138E(H) = 5006(D)/1000= 5.006V
	491
	492
47.1	493	=== 2.3.7 IN1&IN2&INT pin ===
6.2	494
37.2	495
6.2	496	IN1 and IN2 are used as digital input pins.
	497
42.17	498	(% style="color:#037691" %)Example:
6.2	499
42.17	500	09 (H): (0x09&0x08)>>3=1 IN1 pin is high level.
6.2	501
42.17	502	09 (H): (0x09&0x04)>>2=0 IN2 pin is low level.
6.2	503
	504
53.18	505	This data field shows if this packet is generated by (% style="color:blue" %)Interrupt Pin (%%)or not. [[Click here>>\|\|anchor="H3.3.2SetInterruptMode"]] for the hardware and software set up. Note: The Internet Pin is a separate pin in the screw terminal.
6.2	506
42.17	507	(% style="color:#037691" %)Example:
6.2	508
42.17	509	09 (H): (0x09&0x02)>>1=1 The level of the interrupt pin.
6.2	510
42.17	511	09 (H): 0x09&0x01=1 0x00: Normal uplink packet.
6.2	512
	513	0x01: Interrupt Uplink Packet.
	514
50.2	515
72.10	516	=== 2.3.8 Sensor value, FPORT~=7 ===
6.2	517
47.1	518
72.12	519	(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:500px" %)
73.2	520	\|(% style="background-color:#4f81bd; color:white; width:65px" %)(((
47.1	521	Size(bytes)
73.2	522	)))\|(% style="background-color:#4f81bd; color:white; width:35px" %)2\|(% style="background-color:#4f81bd; color:white; width:400px" %)n
60.3	523	\|(% style="width:94px" %)Value\|(% style="width:43px" %)[[BAT>>\|\|anchor="H2.3.3BatteryInfo"]]\|(% style="width:367px" %)(((
47.1	524	Voltage value, each 2 bytes is a set of voltage values.
	525	)))
	526
	527	[[image:image-20230220171300-1.png\|\|height="207" width="863"]]
	528
	529	Multiple sets of data collected are displayed in this form：
	530
48.1	531	[voltage value1], [voltage value2], [voltage value3],…[voltage value n/2]
47.1	532
	533
45.2	534	=== 2.3.9 Decode payload in The Things Network ===
6.2	535
	536
37.2	537	While using TTN network, you can add the payload format to decode the payload.
6.2	538
	539
37.2	540	[[image:1675144839454-913.png]]
6.2	541
	542
72.8	543	PS-LB/LS TTN Payload Decoder: [[https:~~/~~/github.com/dragino/dragino-end-node-decoder>>url:https://github.com/dragino/dragino-end-node-decoder]]
6.2	544
	545
37.2	546	== 2.4 Uplink Interval ==
6.2	547
	548
72.8	549	The PS-LB/LS by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H4.1ChangeUplinkInterval>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H4.1ChangeUplinkInterval\|\|style="background-color: rgb(255, 255, 255);"]]
6.2	550
	551
37.2	552	== 2.5 Show Data in DataCake IoT Server ==
6.2	553
	554
	555	[[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:
	556
	557
42.17	558	(% style="color:blue" %)Step 1: (%%)Be sure that your device is programmed and properly connected to the network at this time.
6.2	559
42.17	560	(% style="color:blue" %)Step 2:(%%) To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:
6.2	561
	562
37.2	563	[[image:1675144951092-237.png]]
6.2	564
	565
37.2	566	[[image:1675144960452-126.png]]
6.2	567
	568
42.17	569	(% style="color:blue" %)Step 3:(%%) Create an account or log in Datacake.
6.2	570
72.8	571	(% style="color:blue" %)Step 4: (%%)Create PS-LB/LS product.
6.2	572
37.2	573	[[image:1675145004465-869.png]]
6.2	574
	575
37.2	576	[[image:1675145018212-853.png]]
6.2	577
	578
	579
37.2	580	[[image:1675145029119-717.png]]
6.2	581
	582
42.17	583	(% style="color:blue" %)Step 5: (%%)add payload decode
6.2	584
37.2	585	[[image:1675145051360-659.png]]
6.2	586
	587
37.2	588	[[image:1675145060812-420.png]]
6.2	589
	590
	591	After added, the sensor data arrive TTN, it will also arrive and show in Datacake.
	592
	593
37.2	594	[[image:1675145081239-376.png]]
6.2	595
	596
37.2	597	== 2.6 Frequency Plans ==
6.2	598
	599
73.4	600	The PS-LB/LS uses OTAA mode and below frequency plans by default. Each frequency band use different firmware, user update the firmware to the corresponding band for their country.
6.2	601
37.3	602	[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/>>http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20Frequency%20Band/]]
6.2	603
	604
37.4	605	== 2.7 Firmware Change Log ==
6.2	606
	607
	608	Firmware download link:
	609
	610	[[https:~~/~~/www.dropbox.com/sh/gf1glloczbzz19h/AABbuYI4WY6VdAmpXo6o1V2Ka?dl=0>>url:https://www.dropbox.com/sh/gf1glloczbzz19h/AABbuYI4WY6VdAmpXo6o1V2Ka?dl=0]]
	611
	612
72.8	613	= 3. Configure PS-LB/LS =
6.2	614
53.1	615	== 3.1 Configure Methods ==
37.4	616
53.7	617
72.8	618	PS-LB/LS supports below configure method:
6.2	619
53.1	620	* AT Command via Bluetooth Connection (Recommand Way): [[BLE Configure Instruction>>url:http://wiki.dragino.com/xwiki/bin/view/Main/BLE%20Bluetooth%20Remote%20Configure/]].
53.20	621	* AT Command via UART Connection : See [[FAQ>>\|\|anchor="H6.FAQ"]].
53.1	622	* LoRaWAN Downlink. Instruction for different platforms: See [[IoT LoRaWAN Server>>url:http://wiki.dragino.com/xwiki/bin/view/Main/]] section.
6.2	623
53.1	624	== 3.2 General Commands ==
6.2	625
53.7	626
6.2	627	These commands are to configure:
	628
	629	* General system settings like: uplink interval.
	630	* LoRaWAN protocol & radio related command.
	631
53.1	632	They are same for all Dragino Devices which support DLWS-005 LoRaWAN Stack. These commands can be found on the wiki:
6.2	633
53.1	634	[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/End%20Device%20AT%20Commands%20and%20Downlink%20Command/]]
6.2	635
	636
72.8	637	== 3.3 Commands special design for PS-LB/LS ==
53.1	638
53.15	639
72.8	640	These commands only valid for PS-LB/LS, as below:
6.2	641
	642
53.1	643	=== 3.3.1 Set Transmit Interval Time ===
6.2	644
37.5	645
6.2	646	Feature: Change LoRaWAN End Node Transmit Interval.
	647
42.21	648	(% style="color:blue" %)AT Command: AT+TDC
6.2	649
53.28	650	(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
72.8	651	\|=(% style="width: 160px; background-color:#4F81BD;color:white" %)Command Example\|=(% style="width: 160px; background-color:#4F81BD;color:white" %)Function\|=(% style="width: 190px;background-color:#4F81BD;color:white" %)Response
53.8	652	\|(% style="background-color:#f2f2f2; width:157px" %)AT+TDC=?\|(% style="background-color:#f2f2f2; width:166px" %)Show current transmit Interval\|(% style="background-color:#f2f2f2" %)(((
6.2	653	30000
	654	OK
	655	the interval is 30000ms = 30s
	656	)))
53.8	657	\|(% style="background-color:#f2f2f2; width:157px" %)AT+TDC=60000\|(% style="background-color:#f2f2f2; width:166px" %)Set Transmit Interval\|(% style="background-color:#f2f2f2" %)(((
6.2	658	OK
	659	Set transmit interval to 60000ms = 60 seconds
	660	)))
	661
42.21	662	(% style="color:blue" %)Downlink Command: 0x01
6.2	663
	664	Format: Command Code (0x01) followed by 3 bytes time value.
	665
43.2	666	If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
6.2	667
43.2	668	* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
	669	* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
6.2	670
53.1	671	=== 3.3.2 Set Interrupt Mode ===
52.2	672
6.2	673
	674	Feature, Set Interrupt mode for GPIO_EXIT.
	675
42.21	676	(% style="color:blue" %)AT Command: AT+INTMOD
6.2	677
53.28	678	(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
72.8	679	\|=(% style="width: 154px;background-color:#4F81BD;color:white" %)Command Example\|=(% style="width: 196px;background-color:#4F81BD;color:white" %)Function\|=(% style="width: 160px;background-color:#4F81BD;color:white" %)Response
53.9	680	\|(% style="background-color:#f2f2f2; width:154px" %)AT+INTMOD=?\|(% style="background-color:#f2f2f2; width:196px" %)Show current interrupt mode\|(% style="background-color:#f2f2f2; width:157px" %)(((
6.2	681	0
	682	OK
47.1	683	the mode is 0 =Disable Interrupt
6.2	684	)))
53.9	685	\|(% style="background-color:#f2f2f2; width:154px" %)AT+INTMOD=2\|(% style="background-color:#f2f2f2; width:196px" %)(((
6.2	686	Set Transmit Interval
47.1	687	0. (Disable Interrupt),
	688	~1. (Trigger by rising and falling edge)
	689	2. (Trigger by falling edge)
	690	3. (Trigger by rising edge)
53.9	691	)))\|(% style="background-color:#f2f2f2; width:157px" %)OK
6.2	692
42.21	693	(% style="color:blue" %)Downlink Command: 0x06
6.2	694
	695	Format: Command Code (0x06) followed by 3 bytes.
	696
	697	This means that the interrupt mode of the end node is set to 0x000003=3 (rising edge trigger), and the type code is 06.
	698
43.2	699	* Example 1: Downlink Payload: 06000000 ~/~/ Turn off interrupt mode
	700	* Example 2: Downlink Payload: 06000003 ~/~/ Set the interrupt mode to rising edge trigger
6.2	701
53.1	702	=== 3.3.3 Set the output time ===
52.2	703
37.5	704
6.2	705	Feature, Control the output 3V3 , 5V or 12V.
	706
42.21	707	(% style="color:blue" %)AT Command: AT+3V3T
6.2	708
53.28	709	(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:474px" %)
72.8	710	\|=(% style="width: 154px;background-color:#4F81BD;color:white" %)Command Example\|=(% style="width: 201px;background-color:#4F81BD;color:white" %)Function\|=(% style="width: 119px;background-color:#4F81BD;color:white" %)Response
53.10	711	\|(% style="background-color:#f2f2f2; width:154px" %)AT+3V3T=?\|(% style="background-color:#f2f2f2; width:201px" %)Show 3V3 open time.\|(% style="background-color:#f2f2f2; width:116px" %)(((
6.2	712	0
	713	OK
	714	)))
53.10	715	\|(% style="background-color:#f2f2f2; width:154px" %)AT+3V3T=0\|(% style="background-color:#f2f2f2; width:201px" %)Normally open 3V3 power supply.\|(% style="background-color:#f2f2f2; width:116px" %)(((
6.2	716	OK
	717	default setting
	718	)))
53.10	719	\|(% style="background-color:#f2f2f2; width:154px" %)AT+3V3T=1000\|(% style="background-color:#f2f2f2; width:201px" %)Close after a delay of 1000 milliseconds.\|(% style="background-color:#f2f2f2; width:116px" %)(((
6.2	720	OK
	721	)))
53.10	722	\|(% style="background-color:#f2f2f2; width:154px" %)AT+3V3T=65535\|(% style="background-color:#f2f2f2; width:201px" %)Normally closed 3V3 power supply.\|(% style="background-color:#f2f2f2; width:116px" %)(((
6.2	723	OK
	724	)))
	725
42.21	726	(% style="color:blue" %)AT Command: AT+5VT
6.2	727
53.28	728	(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:470px" %)
72.8	729	\|=(% style="width: 155px;background-color:#4F81BD;color:white" %)Command Example\|=(% style="width: 196px;background-color:#4F81BD;color:white" %)Function\|=(% style="width: 119px;background-color:#4F81BD;color:white" %)Response
53.10	730	\|(% style="background-color:#f2f2f2; width:155px" %)AT+5VT=?\|(% style="background-color:#f2f2f2; width:196px" %)Show 5V open time.\|(% style="background-color:#f2f2f2; width:114px" %)(((
6.2	731	0
	732	OK
	733	)))
53.10	734	\|(% style="background-color:#f2f2f2; width:155px" %)AT+5VT=0\|(% style="background-color:#f2f2f2; width:196px" %)Normally closed 5V power supply.\|(% style="background-color:#f2f2f2; width:114px" %)(((
6.2	735	OK
	736	default setting
	737	)))
53.10	738	\|(% style="background-color:#f2f2f2; width:155px" %)AT+5VT=1000\|(% style="background-color:#f2f2f2; width:196px" %)Close after a delay of 1000 milliseconds.\|(% style="background-color:#f2f2f2; width:114px" %)(((
6.2	739	OK
	740	)))
53.10	741	\|(% style="background-color:#f2f2f2; width:155px" %)AT+5VT=65535\|(% style="background-color:#f2f2f2; width:196px" %)Normally open 5V power supply.\|(% style="background-color:#f2f2f2; width:114px" %)(((
6.2	742	OK
	743	)))
	744
42.21	745	(% style="color:blue" %)AT Command: AT+12VT
6.2	746
53.28	747	(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:443px" %)
72.8	748	\|=(% style="width: 156px;background-color:#4F81BD;color:white" %)Command Example\|=(% style="width: 199px;background-color:#4F81BD;color:white" %)Function\|=(% style="width: 88px;background-color:#4F81BD;color:white" %)Response
53.10	749	\|(% style="background-color:#f2f2f2; width:156px" %)AT+12VT=?\|(% style="background-color:#f2f2f2; width:199px" %)Show 12V open time.\|(% style="background-color:#f2f2f2; width:83px" %)(((
6.2	750	0
	751	OK
	752	)))
53.10	753	\|(% style="background-color:#f2f2f2; width:156px" %)AT+12VT=0\|(% style="background-color:#f2f2f2; width:199px" %)Normally closed 12V power supply.\|(% style="background-color:#f2f2f2; width:83px" %)OK
	754	\|(% style="background-color:#f2f2f2; width:156px" %)AT+12VT=500\|(% style="background-color:#f2f2f2; width:199px" %)Close after a delay of 500 milliseconds.\|(% style="background-color:#f2f2f2; width:83px" %)(((
6.2	755	OK
	756	)))
	757
42.21	758	(% style="color:blue" %)Downlink Command: 0x07
6.2	759
	760	Format: Command Code (0x07) followed by 3 bytes.
	761
	762	The first byte is which power, the second and third bytes are the time to turn on.
	763
42.32	764	* Example 1: Downlink Payload: 070101F4 ~-~--> AT+3V3T=500
	765	* Example 2: Downlink Payload: 0701FFFF ~-~--> AT+3V3T=65535
	766	* Example 3: Downlink Payload: 070203E8 ~-~--> AT+5VT=1000
	767	* Example 4: Downlink Payload: 07020000 ~-~--> AT+5VT=0
	768	* Example 5: Downlink Payload: 070301F4 ~-~--> AT+12VT=500
	769	* Example 6: Downlink Payload: 07030000 ~-~--> AT+12VT=0
6.2	770
53.1	771	=== 3.3.4 Set the Probe Model ===
52.2	772
37.5	773
47.1	774	Users need to configure this parameter according to the type of external probe. In this way, the server can decode according to this value, and convert the current value output by the sensor into water depth or pressure value.
6.2	775
53.27	776	(% style="color:blue" %)AT Command: AT +PROBE
47.1	777
	778	AT+PROBE=aabb
	779
	780	When aa=00, it is the water depth mode, and the current is converted into the water depth value; bb is the probe at a depth of several meters.
	781
	782	When aa=01, it is the pressure mode, which converts the current into a pressure value;
	783
	784	bb represents which type of pressure sensor it is.
	785
	786	(A->01,B->02,C->03,D->04,E->05,F->06,G->07,H->08,I->09,J->0A,K->0B,L->0C)
	787
53.28	788	(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
73.2	789	\|(% style="background-color:#4f81bd; color:white; width:154px" %)Command Example\|(% style="background-color:#4f81bd; color:white; width:269px" %)Function\|(% style="background-color:#4f81bd; color:white" %)Response
61.1	790	\|(% style="background-color:#f2f2f2; width:154px" %)AT+PROBE=?\|(% style="background-color:#f2f2f2; width:269px" %)Get or Set the probe model.\|(% style="background-color:#f2f2f2" %)0
6.2	791	OK
61.1	792	\|(% style="background-color:#f2f2f2; width:154px" %)AT+PROBE=0003\|(% style="background-color:#f2f2f2; width:269px" %)Set water depth sensor mode, 3m type.\|(% style="background-color:#f2f2f2" %)OK
53.12	793	\|(% style="background-color:#f2f2f2; width:154px" %)(((
61.1	794	AT+PROBE=000A
53.12	795	)))\|(% style="background-color:#f2f2f2; width:269px" %)Set water depth sensor mode, 10m type.\|(% style="background-color:#f2f2f2" %)OK
62.1	796	\|(% style="background-color:#f2f2f2; width:154px" %)AT+PROBE=0064\|(% style="background-color:#f2f2f2; width:269px" %)Set water depth sensor mode, 100m type.\|(% style="background-color:#f2f2f2" %)OK
61.1	797	\|(% style="background-color:#f2f2f2; width:154px" %)AT+PROBE=0101\|(% style="background-color:#f2f2f2; width:269px" %)Set pressure transmitters mode, first type(A).\|(% style="background-color:#f2f2f2" %)OK
	798	\|(% style="background-color:#f2f2f2; width:154px" %)AT+PROBE=0000\|(% style="background-color:#f2f2f2; width:269px" %)Initial state, no settings.\|(% style="background-color:#f2f2f2" %)OK
6.2	799
53.27	800	(% style="color:blue" %)Downlink Command: 0x08
47.1	801
6.2	802	Format: Command Code (0x08) followed by 2 bytes.
	803
47.1	804	* Example 1: Downlink Payload: 080003 ~-~--> AT+PROBE=0003
	805	* Example 2: Downlink Payload: 080101 ~-~--> AT+PROBE=0101
6.2	806
75.2	807	=== 3.3.5 Multiple collections are one uplink (Since firmware V1.1) ===
52.2	808
43.3	809
45.1	810	Added AT+STDC command to collect the voltage of VDC_INPUT multiple times and upload it at one time.
	811
	812	(% style="color:blue" %)AT Command: AT +STDC
	813
47.1	814	AT+STDC=aa,bb,bb
	815
	816	(% style="color:#037691" %)aa:(%%)
	817	0: means disable this function and use TDC to send packets.
	818	1: means enable this function, use the method of multiple acquisitions to send packets.
	819	(% style="color:#037691" %)bb:(%%) Each collection interval (s), the value is 1~~65535
	820	(% style="color:#037691" %)cc:(%%) the number of collection times, the value is 1~~120
	821
53.28	822	(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:510px" %)
73.2	823	\|(% style="background-color:#4f81bd; color:white; width:160px" %)Command Example\|(% style="background-color:#4f81bd; color:white; width:215px" %)Function\|(% style="background-color:#4f81bd; color:white" %)Response
53.13	824	\|(% style="background-color:#f2f2f2; width:160px" %)AT+STDC=?\|(% style="background-color:#f2f2f2; width:215px" %)Get the mode of multiple acquisitions and one uplink.\|(% style="background-color:#f2f2f2" %)1,10,18
45.1	825	OK
53.13	826	\|(% style="background-color:#f2f2f2; width:160px" %)AT+STDC=1,10,18\|(% style="background-color:#f2f2f2; width:215px" %)Set the mode of multiple acquisitions and one uplink, collect once every 10 seconds, and report after 18 times.\|(% style="background-color:#f2f2f2" %)(((
47.1	827	Attention:Take effect after ATZ
	828
	829	OK
45.1	830	)))
53.13	831	\|(% style="background-color:#f2f2f2; width:160px" %)AT+STDC=0, 0,0\|(% style="background-color:#f2f2f2; width:215px" %)(((
47.1	832	Use the TDC interval to send packets.(default)
	833
	834
53.13	835	)))\|(% style="background-color:#f2f2f2" %)(((
47.1	836	Attention:Take effect after ATZ
	837
45.1	838	OK
	839	)))
	840
	841	(% style="color:blue" %)Downlink Command: 0xAE
	842
	843	Format: Command Code (0x08) followed by 5 bytes.
	844
45.3	845	* Example 1: Downlink Payload: AE 01 02 58 12 ~-~--> AT+STDC=1,600,18
45.1	846
53.1	847	= 4. Battery & Power Consumption =
52.2	848
53.13	849
72.3	850	PS-LB use ER26500 + SPC1520 battery pack and PS-LS use 3000mAh Recharable Battery with Solar Panel. See below link for detail information about the battery info and how to replace.
6.2	851
53.14	852	[[Battery Info & Power Consumption Analyze>>url:http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
37.6	853
	854
53.1	855	= 5. OTA firmware update =
6.2	856
	857
42.2	858	Please see this link for how to do OTA firmware update: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20OTA%20Update%20for%20Sensors/]]
6.2	859
	860
53.1	861	= 6. FAQ =
6.2	862
53.1	863	== 6.1 How to use AT Command via UART to access device? ==
6.2	864
	865
42.2	866	See: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]
6.2	867
	868
53.1	869	== 6.2 How to update firmware via UART port? ==
6.2	870
	871
42.2	872	See: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware>>url:http://wiki.dragino.com/xwiki/bin/view/Main/UART%20Access%20for%20LoRa%20ST%20v4%20base%20model/#H1.LoRaSTv4baseHardware]]
6.2	873
	874
53.1	875	== 6.3 How to change the LoRa Frequency Bands/Region? ==
6.2	876
	877
42.3	878	You can follow the instructions for [[how to upgrade image>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome]].
6.2	879	When downloading the images, choose the required image file for download.
	880
	881
76.2	882	== 6.4 How to measure the depth of other liquids other than water? ==
76.1	883
	884
76.2	885	Test the current values at the depth of different liquids and convert them to a linear scale.
	886	Replace its ratio with the ratio of water to current in the decoder.
76.1	887
78.1	888	Example:
76.1	889
78.1	890	Measure the corresponding current of the sensor when the liquid depth is 2.04m and 0.51m.
	891
	892	Calculate scale factor：
	893	Use these two data to calculate the current and depth scaling factors：(7.888-5.035)/(2.04-0.51)=1.86470588235294
	894
	895	Calculation formula：
	896
	897	Use the calibration formula：(Current current - Minimum calibration current)/Scale factor + Minimum actual calibration height
	898
	899	Actual calculations：
	900
	901	Use this formula to calculate the value corresponding to the current at a depth of 1.5 meters: (6.918-5.035)/1.86470588235294+0.51=1.519810726
	902
	903	Error：
	904
	905	0.009810726
	906
	907
	908	[[image:image-20240329175044-1.png]]
	909
62.3	910	= 7. Troubleshooting =
6.2	911
62.3	912	== 7.1 Water Depth Always shows 0 in payload ==
6.2	913
	914
56.1	915	If your device's IDC_intput_mA is normal, but your reading always shows 0, please refer to the following points:
	916
55.1	917	~1. Please set it to mod1
62.3	918
55.1	919	2. Please set the command [[AT+PROBE>>http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/PS-LB%20--%20LoRaWAN%20Pressure%20Sensor/#H3.3.4SettheProbeModel]] according to the model of your sensor
62.3	920
55.1	921	3. Check the connection status of the sensor
6.2	922
56.2	923
62.3	924	= 8. Order Info =
	925
	926
73.2	927	[[image:image-20240109172423-7.png]](% style="display:none" %)
62.3	928
	929
55.1	930	= 9. Packing Info =
	931
	932
42.21	933	(% style="color:#037691" %)Package Includes:
6.2	934
72.4	935	* PS-LB or PS-LS LoRaWAN Pressure Sensor
6.2	936
42.21	937	(% style="color:#037691" %)Dimension and weight:
6.2	938
	939	* Device Size: cm
	940	* Device Weight: g
	941	* Package Size / pcs : cm
	942	* Weight / pcs : g
	943
55.1	944	= 10. Support =
54.3	945
52.2	946
6.2	947	* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
42.20	948
54.3	949	* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[Support@dragino.cc>>mailto:Support@dragino.cc]].
6.2	950
40.4	951

Wiki source code of PS-LB/LS -- LoRaWAN Air Water Pressure Sensor User Manual

Applications

Navigation