Last modified by Bei Jinggeng on 2024/03/30 17:53
<
From version < 56.9 >
edited by Xiaoling
on 2023/04/04 08:50
To version < 43.1 >
edited by David Huang
on 2022/09/07 17:05
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Xiaoling
1 +XWiki.David
Content
... ... @@ -1,43 +1,31 @@
1 1  (% style="text-align:center" %)
2 -[[image:)YK]Y_LZJIO]J2~~VA}OQJM2.png||height="442" width="410"]]
2 +[[image:)YK]Y_LZJIO]J2~~VA}OQJM2.png]]
3 3  
4 -**Table of Contents:**
4 += **1. Introduction** =
5 5  
6 -{{toc/}}
6 +== **1.1 ​What is NSPH01 Soil pH Sensor** ==
7 7  
8 +The Dragino NSPH01 is a **NB-IOT soil ph sensor** for IoT of Agriculture. It is designed to measure the soil PH and soil temperature, so to send to the platform to analyze the soil acid or alkali level. The probe is IP68 waterproof.
8 8  
10 +NSPH01 probe is made by Solid AgCl reference electrode and Pure metal pH sensitive electrode. It can detect soil's** pH **with high accuracy and stable value. The NSPH01 probe can be buried into soil for long time use.
9 9  
10 -= 1.  Introduction =
11 -
12 -== 1.1 ​ What is NSPH01 Soil pH Sensor ==
13 -
14 -
15 -The Dragino NSPH01 is a (% style="color:blue" %)**NB-IoT soil pH sensor**(%%) for IoT of Agriculture. It is designed to measure the soil pH and soil temperature, so to send to the platform to analyze the soil acid or alkali level. The probe is IP68 waterproof.
16 -
17 -NSPH01 probe is made by Solid AgCl reference electrode and Pure metal pH sensitive electrode. It can detect soil's** (% style="color:blue" %)pH (%%)**with high accuracy and stable value. The NSPH01 probe can be buried into soil for long time use.
18 -
19 19  NarrowBand-Internet of Things (NB-IoT) is a standards-based low power wide area (LPWA) technology developed to enable a wide range of new IoT devices and services. NB-IoT significantly improves the power consumption of user devices, system capacity and spectrum efficiency, especially in deep coverage.
13 +\\NSPH01 supports different uplink methods include **TCP,MQTT,UDP and CoAP  **for different application requirement.
14 +\\NSPH01 is powered by  **8500mAh Li-SOCI2 battery**, It is designed for long term use up to 5 years. (Actually Battery life depends on the use environment, update period & uplink method)
15 +\\To use NSPH01, user needs to check if there is NB-IoT coverage in local area and with the bands NSPH01 supports. If the local operate support it, user needs to get a **NB-IoT SIM card** from local operator and install NSPH01 to get NB-IoT network connection.
20 20  
21 -NSPH01 supports different uplink methods include (% style="color:blue" %)**TCP,MQTT,UDP and CoAP  **(%%)for different application requirement.
22 -
23 -NSPH01 is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), It is designed for long term use up to 5 years. (Actually Battery life depends on the use environment, update period & uplink method)
24 -
25 -To use NSPH01, user needs to check if there is NB-IoT coverage in the installation area and with the bands NSPH01 supports. If the local operator supports it, user needs to get a (% style="color:blue" %)**NB-IoT SIM card** (%%)from local operator and install NSPH01 to get NB-IoT network connection.
26 -
27 -
17 +(% style="text-align:center" %)
28 28  [[image:image-20220907153151-1.png]]
29 29  
30 -
20 +(% style="text-align:center" %)
31 31  [[image:M_K`YF9`CAYAE\@}3T]FHT$9.png]]
32 32  
23 +**1.2 Features**
33 33  
34 -== 1.2  Features ==
35 -
36 -
37 37  * NB-IoT Bands: B1/B3/B8/B5/B20/B28 @H-FDD
38 38  * Monitor soil pH with temperature compensation.
39 39  * Monitor soil temperature
40 -* pH and Temperature alarm function
28 +* PH and Temperature alarm function
41 41  * Monitor Battery Level
42 42  * Support pH calibration by end user
43 43  * Uplink on periodically
... ... @@ -46,31 +46,29 @@
46 46  * IP68 rate for the Sensor Probe
47 47  * Ultra-Low Power consumption
48 48  * AT Commands to change parameters
49 -* Micro SIM card slot
37 +* Micro SIM card slot for NB-IoT SIM
50 50  * 8500mAh Battery for long term use
51 51  
52 -== 1.3  Specification ==
40 +**1.3  Specification**
53 53  
42 +**Common DC Characteristics:**
54 54  
55 -(% style="color:#037691" %)**Common DC Characteristics:**
56 -
57 57  * Supply Voltage: 2.1v ~~ 3.6v
58 58  * Operating Temperature: -40 ~~ 85°C
59 59  
60 -(% style="color:#037691" %)**NB-IoT Spec:**
47 +**NB-IoT Spec:**
61 61  
62 -* B1 @H-FDD: 2100MHz
63 -* B3 @H-FDD: 1800MHz
64 -* B8 @H-FDD: 900MHz
65 -* B5 @H-FDD: 850MHz
66 -* B20 @H-FDD: 800MHz
67 -* B28 @H-FDD: 700MHz
49 +* - B1 @H-FDD: 2100MHz
50 +* - B3 @H-FDD: 1800MHz
51 +* - B8 @H-FDD: 900MHz
52 +* - B5 @H-FDD: 850MHz
53 +* - B20 @H-FDD: 800MHz
54 +* - B28 @H-FDD: 700MHz
68 68  
69 -== 1.4  Probe Specification ==
56 +**1.4 Probe Specification**
70 70  
58 +**Soil pH:**
71 71  
72 -(% style="color:#037691" %)**Soil pH:**
73 -
74 74  * Range: 3 ~~ 10 pH
75 75  * Resolution: 0.01 pH
76 76  * Accuracy: ±2% under (0~~50 ℃, Accuracy will poor under 0 due to frozen)
... ... @@ -78,7 +78,7 @@
78 78  * IP68 Protection
79 79  * Length: 3.5 meters
80 80  
81 -(% style="color:#037691" %)**Soil Temperature:**
67 +**Soil Temperature:**
82 82  
83 83  * Range -40℃～85℃
84 84  * Resolution: 0.1℃
... ... @@ -86,241 +86,199 @@
86 86  * IP68 Protection
87 87  * Length: 3.5 meters
88 88  
89 -== 1.5  ​Applications ==
75 +**1.5 ​Applications**
90 90  
91 -
92 92  * Smart Agriculture
93 93  
94 -== 1.6  Pin mapping and power on ==
79 +**1.6 Pin mapping and power on**
95 95  
96 -
81 +(% style="text-align:center" %)
97 97  [[image:image-20220907153300-2.png]]
98 98  
99 99  
85 +**2.  Use NSPH01 to communicate with IoT Server**
100 100  
101 -= 2.  Use NSPH01 to communicate with IoT Server =
87 +**2.1  How it works**
102 102  
103 -== 2.1  How it works ==
104 -
105 -
106 106  The NSPH01 is equipped with a NB-IoT module, the pre-loaded firmware in NSPH01 will get environment data from sensors and send the value to local NB-IoT network via the NB-IoT module.  The NB-IoT network will forward this value to IoT server via the protocol defined by NSPH01.
107 107  
108 108  The diagram below shows the working flow in default firmware of NSPH01:
109 109  
110 -
93 +(% style="text-align:center" %)
111 111  [[image:image-20220907153416-3.png]]
112 112  
96 +**2.2 ​ Configure the NSPH01**
113 113  
98 +**2.2.1 Test Requirement**
114 114  
115 -== 2.2 ​ Configure the NSPH01 ==
100 +To use NSPH01 in your city, make sure meet below requirements:
116 116  
117 -=== 2.2.1 Test Requirement ===
118 -
119 -
120 -To use NSPH01 in the field, make sure meet below requirements:
121 -
122 122  * Your local operator has already distributed a NB-IoT Network there.
123 123  * The local NB-IoT network used the band that NSPH01 supports.
124 124  * Your operator is able to distribute the data received in their NB-IoT network to your IoT server.
125 125  
126 -Below figure shows our testing structure. Here we have NB-IoT network coverage by China Mobile, the band they use is B8.  The NSPH01 will use** CoAP(120.24.4.116:5683) **or raw **UDP(120.24.4.116:5601)** or **MQTT(120.24.4.116:1883)**or **TCP(120.24.4.116:5600)**protocol to send data to the test server.
106 +Below figure shows our testing structure. Here we have NB-IoT network coverage by China Mobile, the band they use is B8.  The NSPH01 will use CoAP(120.24.4.116:5683) or raw UDP(120.24.4.116:5601) or MQTT(120.24.4.116:1883)or TCP(120.24.4.116:5600)protocol to send data to the test server
127 127  
128 -
108 +(% style="text-align:center" %)
129 129  [[image:image-20220907153445-4.png]]
130 130  
131 131  
132 -=== 2.2.2 Insert SIM card ===
112 +**2.2.2 Insert SIM card**
133 133  
114 +Insert the NB-IoT Card get from your provider.
134 134  
135 -User need to take out the NB-IoT module and insert the SIM card like below. ((% style="color:red" %) Pay attention to the direction(%%))
116 +User need to take out the NB-IoT module and insert the SIM card like below:
136 136  
137 -
118 +(% style="text-align:center" %)
138 138  [[image:image-20220907153505-5.png]]
139 139  
121 +**2.2.3 Connect USB – TTL to NSPH01 to configure it**
140 140  
141 -=== 2.2.3 Connect USB – TTL to NSPH01 to configure it ===
123 +User need to configure NSPH01 via serial port to set the **Server Address** / **Uplink Topic** to define where and how-to uplink packets. NSPH01 support AT Commands, user can use a USB to TTL adapter to connect to NSPH01 and use AT Commands to configure it, as below.
142 142  
125 +**Connection:**
143 143  
144 -User need to configure NSPH01 via serial port to set the (% style="color:blue" %)**Server Address** / **Uplink Topic**(%%) to define where and how-to uplink packets. NSPH01 support AT Commands, user can use a USB to TTL adapter to connect to NSPH01 and use AT Commands to configure it, as below.
127 + USB TTL GND <~-~-~-~-> GND
145 145  
129 + USB TTL TXD <~-~-~-~-> UART_RXD
146 146  
147 -(% style="color:blue" %)**Connection:**
131 + USB TTL RXD <~-~-~-~-> UART_TXD
148 148  
149 -**~ (% style="background-color:yellow" %) USB TTL GND <~-~-~-~->  GND(%%)**
150 -
151 -**~ (% style="background-color:yellow" %) USB TTL TXD  <~-~-~-~->  UART_RXD(%%)**
152 -
153 -**~ (% style="background-color:yellow" %) USB TTL RXD  <~-~-~-~->  UART_TXD(%%)**
154 -
155 -
156 156  In the PC, use below serial tool settings:
157 157  
158 -* Baud:  (% style="color:green" %)**9600**
159 -* Data bits:**  (% style="color:green" %)8(%%)**
160 -* Stop bits:  (% style="color:green" %)**1**
161 -* Parity:  (% style="color:green" %)**None**
162 -* Flow Control: (% style="color:green" %)**None**
135 +* Baud:  **9600**
136 +* Data bits:** 8**
137 +* Stop bits: **1**
138 +* Parity:  **None**
139 +* Flow Control: **None**
163 163  
164 -Make sure the switch is in FLASH position, then power on device by connecting the jumper on NSPH01. NSPH01 will output system info once power on as below, we can enter the (% style="color:green" %)**password: 12345678**(%%) to access AT Command input.
141 +Make sure the switch is in FLASH position, then power on device by connecting the jumper on NSPH01. NSPH01 will output system info once power on as below, we can enter the **password: 12345678** to access AT Command input.
165 165  
143 +(% style="text-align:center" %)
144 +[[image:image-20220907153529-6.png]]
166 166  
167 -[[image:image-20220912144017-1.png]]
146 +**Note: the valid AT Commands can be found at:  **[[**https:~~/~~/www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0**>>url:https://www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0]]
168 168  
148 +**2.2.4 Use CoAP protocol to uplink data**
169 169  
170 -(% style="color:red" %)**Note: the valid AT Commands can be found at:**(%%)**  **[[**https:~~/~~/www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0**>>url:https://www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0]]
150 +**Note: if you don't have CoAP server, you can refer this link to set up one: **[[**http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/**>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/]]
171 171  
152 +**Use below commands:**
172 172  
173 -=== 2.2.4 Use CoAP protocol to uplink data ===
154 +* **AT+PRO=1**   ~/~/ Set to use CoAP protocol to uplink
155 +* **AT+SERVADDR=120.24.4.116,5683   ** ~/~/ to set CoAP server address and port
156 +* **AT+URI=5,11,"mqtt",11,"coap",12,"0",15,"c=text1",23,"0" ** ~/~/Set COAP resource path
174 174  
175 -
176 -(% style="color:red" %)**Note: if you don't have CoAP server, you can refer this link to set up one:**(%%)** **[[**http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/**>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/]]
177 -
178 -
179 -(% style="color:blue" %)**Use below commands:**
180 -
181 -* (% style="color:#037691" %)**AT+PRO=1**                         (%%) ~/~/  Set to use CoAP protocol to uplink
182 -* (% style="color:#037691" %)**AT+SERVADDR=120.24.4.116,5683   ** (%%) ~/~/  to set CoAP server address and port
183 -* (% style="color:#037691" %)**AT+URI=5,11,"mqtt",11,"coap",12,"0",15,"c=text1",23,"0" ** (%%) ~/~/  Set COAP resource path
184 -
185 185  For parameter description, please refer to AT command set
186 186  
187 -
160 +(% style="text-align:center" %)
188 188  [[image:image-20220907153551-7.png||height="502" width="740"]]
189 189  
163 +After configure the server address and **reset the device** (via AT+ATZ ), NSPH01 will start to uplink sensor values to CoAP server.
190 190  
191 -After configure the server address and (% style="color:green" %)**reset the device (via AT+ATZ )**(%%), NSPH01 will start to uplink sensor values to CoAP server.
192 -
193 -
165 +(% style="text-align:center" %)
194 194  [[image:image-20220907153612-8.png||height="529" width="729"]]
195 195  
196 196  
197 -=== 2.2.5 Use UDP protocol to uplink data(Default protocol) ===
169 +**2.2.5 Use UDP protocol to uplink data(Default protocol)**
198 198  
199 -
200 200  This feature is supported since firmware version v1.0.1
201 201  
202 -* (% style="color:blue" %)**AT+PRO=2   ** (%%) ~/~/  Set to use UDP protocol to uplink
203 -* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5601   ** (%%) ~/~/  to set UDP server address and port
204 -* (% style="color:blue" %)**AT+CFM=1       ** (%%) ~/~/  If the server does not respond, this command is unnecessar
173 +* **AT+PRO=2   ** ~/~/ Set to use UDP protocol to uplink
174 +* **AT+SERVADDR=120.24.4.116,5601   ** ~/~/ to set UDP server address and port
175 +* **AT+CFM=1       ** ~/~/If the server does not respond, this command is unnecessar
205 205  
177 +(% style="text-align:center" %)
206 206  [[image:image-20220907153643-9.png||height="401" width="734"]]
207 207  
208 -
180 +(% style="text-align:center" %)
209 209  [[image:image-20220907153703-10.png||height="309" width="738"]]
210 210  
211 211  
212 -=== 2.2.6 Use MQTT protocol to uplink data ===
184 +**2.2.6 Use MQTT protocol to uplink data**
213 213  
214 -
215 215  This feature is supported since firmware version v110
216 216  
217 -* (% style="color:blue" %)**AT+PRO=3   ** (%%) ~/~/ Set to use MQTT protocol to uplink
218 -* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,1883   ** (%%) ~/~/ Set MQTT server address and port
219 -* (% style="color:blue" %)**AT+CLIENT=CLIENT       ** (%%) ~/~/ Set up the CLIENT of MQTT
220 -* (% style="color:blue" %)**AT+UNAME=UNAME                               **(%%)~/~/ Set the username of MQTT
221 -* (% style="color:blue" %)**AT+PWD=PWD                                        **(%%)~/~/ Set the password of MQTT
222 -* (% style="color:blue" %)**AT+PUBTOPIC=NSE01_PUB                    **(%%)~/~/ Set the sending topic of MQTT
223 -* (% style="color:blue" %)**AT+SUBTOPIC=NSE01_SUB          ** (%%) ~/~/ Set the subscription topic of MQTT
188 +* **AT+PRO=3   ** ~/~/Set to use MQTT protocol to uplink
189 +* **AT+SERVADDR=120.24.4.116,1883   ** ~/~/Set MQTT server address and port
190 +* **AT+CLIENT=CLIENT       ** ~/~/Set up the CLIENT of MQTT
191 +* **AT+UNAME=UNAME                               **~/~/Set the username of MQTT
192 +* **AT+PWD=PWD                                        **~/~/Set the password of MQTT
193 +* **AT+PUBTOPIC=NSE01_PUB                    **~/~/Set the sending topic of MQTT
194 +* **AT+SUBTOPIC=NSE01_SUB          ** ~/~/Set the subscription topic of MQTT
224 224  
196 +(% style="text-align:center" %)
225 225  [[image:image-20220907153739-11.png||height="491" width="764"]]
226 226  
227 -
199 +(% style="text-align:center" %)
228 228  [[image:image-20220907153751-12.png||height="555" width="769"]]
229 229  
230 -
231 231  MQTT protocol has a much higher power consumption compare vs UDP / CoAP protocol. Please check the power analyze document and adjust the uplink period to a suitable interval.
232 232  
204 +**2.2.7 Use TCP protocol to uplink data**
233 233  
234 -=== 2.2.7 Use TCP protocol to uplink data ===
235 -
236 -
237 237  This feature is supported since firmware version v110
238 238  
239 -* (% style="color:blue" %)**AT+PRO=4   ** (%%) ~/~/ Set to use TCP protocol to uplink
240 -* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5600   ** (%%) ~/~/ to set TCP server address and port
208 +* **AT+PRO=4   ** ~/~/ Set to use TCP protocol to uplink
209 +* **AT+SERVADDR=120.24.4.116,5600   ** ~/~/ to set TCP server address and port
241 241  
211 +(% style="text-align:center" %)
242 242  [[image:image-20220907153818-13.png||height="486" width="668"]]
243 243  
244 -
214 +(% style="text-align:center" %)
245 245  [[image:image-20220907153827-14.png||height="236" width="684"]]
246 246  
217 +**2.2.8 Change Update Interval**
247 247  
248 -=== 2.2.8 Change Update Interval ===
219 +User can use below command to change the **uplink interval**.
249 249  
221 +* **AT+TDC=600      ** ~/~/ Set Update Interval to 600s
250 250  
251 -Users can use the below command to change the **uplink interval**.
223 +**NOTE:**
252 252  
253 -* (% style="color:blue" %)**AT+TDC=7200      ** (%%) ~/~/ Set Update Interval to 7200s (2 hour)
225 +**~1. By default, the device will send an uplink message every 2 hour.**
254 254  
255 -(% style="color:red" %)**NOTE: By default, the device will send an uplink message every 2 hours. Each Uplink Include 8 set of records in this 2 hour (15 minute interval / record).**
227 +**2.3  Uplink Payload**
256 256  
257 -
258 -== 2.3  Uplink Payload ==
259 -
260 -
261 261  In this mode, uplink payload includes 87 bytes in total by default.
262 262  
263 263  Each time the device uploads a data package, 8 sets of recorded data will be attached. Up to 32 sets of recorded data can be uploaded.
264 264  
265 -(% border="1.5" style="background-color:#ffffcc; color:green; width:520px" %)
266 -|=(% scope="row" style="width: 50px;" %)**Size(bytes)**|(% style="width:40px" %)**8**|(% style="width:20px" %)**2**|(% style="width:25px" %)**2**|(% style="width:60px" %)**1**|(% style="width:20px" %)**1**|(% style="width:40px" %)**1**|(% style="width:40px" %)**2**|(% style="width:50px" %)**2**|(% style="width:50px" %)**4**|(% style="width:50px" %)**2**|(% style="width:35px" %)**2**|(% style="width:40px" %)**4**
267 -|=(% style="width: 96px;" %)**Value**|(% style="width:83px" %)Device ID|(% style="width:44px" %)Ver|(% style="width:42px" %)BAT|(% style="width:124px" %)Signal Strength|(% style="width:57px" %)MOD|(% style="width:80px" %)Interrupt|(% style="width:69px" %)Soil PH|(% style="width:134px" %)Soil Temperature|(% style="width:98px" %)Time stamp|(% style="width:134px" %)Soil Temperature|(% style="width:68px" %)Soil PH|(% style="width:125px" %)Time stamp  .....
233 +(% style="width:934px" %)
234 +|(% style="width:93px" %)**Size(bytes)**|(% style="width:82px" %)**8**|(% style="width:43px" %)**2**|(% style="width:41px" %)**2**|(% style="width:126px" %)**1**|(% style="width:54px" %)**1**|(% style="width:84px" %)1|(% style="width:75px" %)2|(% style="width:133px" %)2|(% style="width:70px" %)2|(% style="width:127px" %)4   
235 +|(% style="width:93px" %)**Value**|(% style="width:82px" %)Device ID|(% style="width:43px" %)Ver|(% style="width:41px" %)BAT|(% style="width:126px" %)Signal Strength|(% style="width:54px" %)MOD|(% style="width:84px" %)Interrupt|(% style="width:75px" %)Soil PH|(% style="width:133px" %)Soil Temperature|(% style="width:70px" %)Soil PH|(% style="width:127px" %)Time stamp  .....
268 268  
269 269  If we use the MQTT client to subscribe to this MQTT topic, we can see the following information when the NSPH01 uplink data.
270 270  
239 +(% style="text-align:center" %)
271 271  [[image:image-20220907153902-15.png||height="581" width="804"]]
272 272  
273 273  
274 -(((
275 275  The payload is ASCII string, representative same HEX:
276 -)))
277 277  
278 -(((
279 -
280 -)))
245 +0xf86841105675413800640c781701000225010b6315537b010b0226631550fb010e022663154d7701110225631549f1011502246315466b01190223631542e5011d022163153f62011e022163153bde011e022163153859 where:
281 281  
282 -(((
283 -**0x (% style="color:red" %)__f868411056754138__  (% style="color:blue" %)__0064 __ (% style="color:green" %)__0c78__  (% style="color:#00b0f0" %)__17__  (% style="color:#7030a0" %)__01__  (% style="color:#d60093" %)__00__  (% style="color:#a14d07" %)__0225 __ (% style="color:#0020b0" %) __010b__  (% style="color:#420042" %)__6315537b__  (% style="color:#663300" %)//__010b0226631550fb__  __010e022663154d77  01110225631549f1  011502246315466b  01190223631542e5  011d022163153f62  011e022163153bde 011e022163153859__//(%%)**
284 -)))
247 +* Device ID: 0xf868411056754138 = f868411056754138
248 +* Version: 0x0064=100=1.0.0
285 285  
286 -(((
287 -
250 +* BAT: 0x0c78 = 3192 mV = 3.192V
251 +* Singal: 0x17 = 23
252 +* Mod: 0x01 = 1
253 +* Interrupt: 0x00= 0
254 +* Soil PH: 0x0225= 549 = 5.49
255 +* Soil Temperature:0x010B =267=26.7 °C
256 +* Time stamp : 0x6315537b =1662342011
257 +* Soil Temperature,Soil PH,Time stamp : 010b0226631550fb
258 +* 8 sets of recorded data: Temperature,Soil PH,Time stamp : 010e022663154d77,.......
288 288  
289 -**where:**
290 -)))
260 +**2.4  Payload Explanation and Sensor Interface**
291 291  
292 -* (% style="color:#037691" %)**Device ID:**(%%)** **0xf868411056754138 = f868411056754138
262 +**2.4.1  Device ID**
293 293  
294 -* (% style="color:#037691" %)**Version:**  (%%) 0x0064=100=1.0.0
295 -
296 -* (% style="color:#037691" %)**BAT:**   (%%) 0x0c78 = 3192 mV = 3.192V
297 -
298 -* (% style="color:#037691" %)**Singal:** (%%)0x17 = 23
299 -
300 -* (% style="color:#037691" %)**Mod:** (%%) 0x01 = 1
301 -
302 -* (% style="color:#037691" %)**Interrupt:**(%%) 0x00= 0
303 -
304 -* (% style="color:#037691" %)**Soil PH:** (%%) 0x0225= 549 = 5.49
305 -
306 -* (% style="color:#037691" %)**Soil Temperature:**(%%) 0x010b =267=26.7 °C
307 -
308 -* (% style="color:#037691" %)**Time stamp :**   (%%) 0x6315537b =1662342011  ([[Unix Epoch Time>>url:http://www.epochconverter.com/]])
309 -
310 -* (% style="color:#037691" %)**Soil Temperature,Soil PH,Time stamp : **(%%) 010b0226631550fb
311 -
312 -* (% style="color:#037691" %)**8 sets of recorded data:**(%%) Temperature,Soil PH,Time stamp :  010e022663154d77,.......
313 -
314 -== 2.4  Payload Explanation and Sensor Interface ==
315 -
316 -=== 2.4.1  Device ID ===
317 -
318 -
319 319  By default, the Device ID equal to the last 15 bits of IMEI.
320 320  
321 -User can use (% style="color:blue" %)**AT+DEUI** (%%)to set Device ID
266 +User can use **AT+DEUI** to set Device ID
322 322  
323 -
324 324  **Example:**
325 325  
326 326  AT+DEUI=868411056754138
... ... @@ -327,18 +327,14 @@
327 327  
328 328  The Device ID is stored in a none-erase area, Upgrade the firmware or run AT+FDR won't erase Device ID.
329 329  
274 +**2.4.2  Version Info**
330 330  
331 -=== 2.4.2  Version Info ===
332 -
333 -
334 334  Specify the software version: 0x64=100, means firmware version 1.00.
335 335  
336 336  For example: 0x00 64 : this device is NSPH01 with firmware version 1.0.0.
337 337  
280 +**2.4.3  Battery Info**
338 338  
339 -=== 2.4.3  Battery Info ===
340 -
341 -
342 342  Check the battery voltage for NSPH01.
343 343  
344 344  Ex1: 0x0B45 = 2885mV
... ... @@ -345,10 +345,8 @@
345 345  
346 346  Ex2: 0x0B49 = 2889mV
347 347  
288 +**2.4.4  Signal Strength**
348 348  
349 -=== 2.4.4  Signal Strength ===
350 -
351 -
352 352  NB-IoT Network signal Strength.
353 353  
354 354  **Ex1: 0x1d = 29**
... ... @@ -363,23 +363,18 @@
363 363  
364 364  **99**    Not known or not detectable
365 365  
304 +**2.4.5  Soil PH**
366 366  
367 -=== 2.4.5  Soil PH ===
368 -
369 -
370 370  Get the PH content of the soil. The value range of the register is 300-1000(Decimal), divide this value by 100 to get the percentage of PH in the soil.
371 371  
372 -For example, if the data you get from the register is (% style="color:blue" %)**__0x05 0xDC__**(%%), the PH content in the soil is
308 +For example, if the data you get from the register is **__0x05 0xDC__**, the PH content in the soil is
373 373  
374 -(% style="color:blue" %)**0229(H) = 549(D) /100 = 5.49.**
310 +**0229(H) = 549(D) /100 = 5.49.**
375 375  
312 +**2.4.6  Soil Temperature**
376 376  
377 -=== 2.4.6  Soil Temperature ===
314 +Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is **__0x09 0xEC__**, the temperature content in the soil is
378 378  
379 -
380 -Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is (% style="color:blue" %)**__0x09 0xEC__**(%%), the temperature content in the soil is
381 -
382 -
383 383  **Example**:
384 384  
385 385  If payload is 0105H: ((0x0105 & 0x8000)>>15 === 0),temp = 0105(H)/10 = 26.1 °C
... ... @@ -386,58 +386,56 @@
386 386  
387 387  If payload is FF7EH: ((FF7E & 0x8000)>>15 ===1),temp = (FF7E(H)-FFFF(H))/10 = -12.9 °C
388 388  
322 +**2.4.7  Timestamp**
389 389  
390 -=== 2.4.7  Timestamp ===
391 -
392 -
393 393  Time stamp : 0x6315537b =1662342011
394 394  
395 395  Convert Unix timestamp to time 2022-9-5 9:40:11.
396 396  
328 +**2.4.8  Digital Interrupt**
397 397  
398 -=== 2.4.8  Digital Interrupt ===
330 +Digital Interrupt refers to pin **GPIO_EXTI**, and there are different trigger methods. When there is a trigger, the NSPH01 will send a packet to the server.
399 399  
400 -
401 -Digital Interrupt refers to pin (% style="color:blue" %)**GPIO_EXTI**(%%), and there are different trigger methods. When there is a trigger, the NSPH01 will send a packet to the server.
402 -
403 403  The command is:
404 404  
405 -(% style="color:blue" %)**AT+INTMOD=3 ** (%%) ~/~/(more info about INMOD please refer [[**AT Command Manual**>>url:https://www.dragino.com/downloads/downloads/NB-IoT/NBSN95/DRAGINO_NBSN95-NB_AT%20Commands_v1.1.0.pdf]])**.**
334 +**AT+INTMOD=3 ** ~/~/(more info about INMOD please refer [[**AT Command Manual**>>url:https://www.dragino.com/downloads/downloads/NB-IoT/NBSN95/DRAGINO_NBSN95-NB_AT%20Commands_v1.1.0.pdf]])**.**
406 406  
407 407  The lower four bits of this data field shows if this packet is generated by interrupt or not. Click here for the hardware and software set up.
408 408  
338 +Example:
409 409  
410 -**Example:**
411 -
412 412  0x(00): Normal uplink packet.
413 413  
414 414  0x(01): Interrupt Uplink Packet.
415 415  
344 +**2.4.9  ​+5V Output**
416 416  
417 -=== 2.4.9  ​+5V Output ===
418 -
419 -
420 420  NSPH01 will enable +5V output before all sampling and disable the +5v after all sampling. 
421 421  
422 422  The 5V output time can be controlled by AT Command.
423 423  
424 -(% style="color:blue" %)**AT+5VT=1000**
350 +**AT+5VT=1000**
425 425  
426 426  Means set 5V valid time to have 1000ms. So the real 5V output will actually have 1000ms + sampling time for other sensors.** **
427 427  
428 428  
429 -== 2.5  Downlink Payload ==
355 +**2.5  Downlink Payload**
430 430  
431 -
432 432  By default, NSPH01 prints the downlink payload to console port.
433 433  
359 +(% style="text-align:center" %)
434 434  [[image:image-20220907154636-17.png]]
435 435  
436 436  
437 -(% style="color:blue" %)**Examples:**
438 438  
439 -* (% style="color:#037691" %)** Set TDC**
440 440  
365 +
366 +
367 +
368 +**Examples:**
369 +
370 +* **Set TDC**
371 +
441 441  If the payload=0100003C, it means set the END Node's TDC to 0x00003C=60(S), while type code is 01.
442 442  
443 443  Payload:    01 00 00 1E    TDC=30S
... ... @@ -444,18 +444,16 @@
444 444  
445 445  Payload:    01 00 00 3C    TDC=60S
446 446  
447 -* (% style="color:#037691" %)** Reset**
378 +* **Reset**
448 448  
449 449  If payload = 0x04FF, it will reset the NSPH01
450 450  
451 -* (% style="color:#037691" %)** INTMOD**
382 +* **INTMOD**
452 452  
453 453  Downlink Payload: 06000003, Set AT+INTMOD=3
454 454  
386 +**2.6  ​LED Indicator**
455 455  
456 -== 2.6  ​LED Indicator ==
457 -
458 -
459 459  The NSPH01 has an internal LED which is to show the status of different state.
460 460  
461 461  * When power on, NSPH01 will detect if sensor probe is connected, if probe detected, LED will blink four times. (no blinks in this step is no probe)
... ... @@ -463,20 +463,16 @@
463 463  * After NSPH01 join NB-IoT network. The LED will be ON for 3 seconds.
464 464  * For each uplink probe, LED will be on for 500ms.
465 465  
466 -== 2.7  Installation and Maintain ==
395 +**2.7 Installation and Maintain**
467 467  
468 -=== 2.7.1  Before measurement ===
397 +**2.7.1 Before measurement**
469 469  
470 -
471 471  If the NSPH01 has more than 7 days not use or just clean the pH probe. User should put the probe inside pure water for more than 24 hours for activation. If no put in water, user need to put inside soil for more than 24 hours to ensure the measurement accuracy. 
472 472  
401 +**2.7.2 Measurement**
473 473  
474 -=== 2.7.2  Measurement ===
403 +**Measurement the soil surface:**
475 475  
476 -
477 -(% style="color:#037691" %)**Measurement the soil surface:**
478 -
479 -
480 480  [[image:image-20220907154700-18.png]] ​
481 481  
482 482  Choose the proper measuring position. Split the surface soil according to the measured deep.
... ... @@ -487,17 +487,14 @@
487 487  
488 488  Put soil over the probe after insert. And start to measure.
489 489  
415 +**Measurement inside soil:**
490 490  
491 -(% style="color:#037691" %)**Measurement inside soil:**
492 -
493 493  Dig a hole with diameter > 20CM.
494 494  
495 495  Insert the probe inside, method like measure the surface.
496 496  
421 +**2.7.3 Maintain Probe**
497 497  
498 -=== 2.7.3  Maintain Probe ===
499 -
500 -
501 501  1. pH probe electrode is fragile and no strong. User must avoid strong force or hitting it.
502 502  1. After long time use (3~~ 6  months). The probe electrode needs to be clean; user can use high grade sandpaper to polish it or put in 5% hydrochloric acid for several minutes. After the metal probe looks like new, user can use pure water to wash it.
503 503  1. Probe reference electrode is also no strong, need to avoid strong force or hitting.
... ... @@ -505,13 +505,12 @@
505 505  1. Avoid the probes to touch oily matter. Which will cause issue in accuracy.
506 506  1. The probe is IP68 can be put in water.
507 507  
508 -== 2.8  PH and Temperature alarm function ==
430 +**2.8 PH and Temperature alarm function**
509 509  
432 +➢ AT Command:
510 510  
511 -(% style="color:#037691" %)**➢ AT Command:**
434 +AT+ PHALARM=min,max
512 512  
513 -(% style="color:blue" %)**AT+ PHALARM=min,max**
514 -
515 515  ² When min=3, and max≠0, Alarm higher than max
516 516  
517 517  ² When min≠0, and max=0, Alarm lower than min
... ... @@ -518,11 +518,10 @@
518 518  
519 519  ² When min≠0 and max≠0, Alarm higher than max or lower than min
520 520  
442 +Example:
521 521  
522 -(% style="color:blue" %)**Example:**
444 +AT+ PHALARM =5,8 ~/~/ Alarm when PH lower than 5.
523 523  
524 -AT+ PHALARM =5,8  ~/~/ Alarm when PH lower than 5.
525 -
526 526  AT+ TEMPALARM=min,max
527 527  
528 528  ² When min=0, and max≠0, Alarm higher than max
... ... @@ -531,80 +531,106 @@
531 531  
532 532  ² When min≠0 and max≠0, Alarm higher than max or lower than min
533 533  
454 +Example:
534 534  
535 -(% style="color:blue" %)**Example:**
456 +AT+ TEMPALARM=20,30 ~/~/ Alarm when temperature lower than 20.
536 536  
537 -AT+ TEMPALARM=20,30  ~/~/ Alarm when temperature lower than 20.
538 538  
459 +**2.9 Set the number of data to be uploaded and the recording time**
539 539  
540 -== 2.9  Set the number of data to be uploaded and the recording time ==
461 +➢ AT Command:
541 541  
463 +AT+TR=900  ~/~/The unit is seconds, and the default is to record data once every 900 seconds.( The minimum can be set to 180 seconds)
542 542  
543 -(% style="color:#037691" %)**➢ AT Command:**
544 544  
545 -* (% style="color:blue" %)**AT+TR=900**     (%%) ~/~/  The unit is seconds, and the default is to record data once every 900 seconds.( The minimum can be set to 180 seconds)
546 -* (% style="color:blue" %)**AT+NOUD=8**     (%%) ~/~/  The device uploads 8 sets of recorded data by default. Up to 32 sets of record data can be uploaded.
466 +AT+NOUD=8  ~/~/The device uploads 8 sets of recorded data by default. Up to 32 sets of record data can be uploaded.
547 547  
548 - The diagram below explains the relationship between TR, NOUD, and TDC more clearly**:**
468 +**2.10 Read or Clear cached data**
549 549  
550 -[[image:image-20221009000933-1.png||height="750" width="1043"]]
470 +➢ AT Command:
551 551  
472 +AT+CDP ~/~/ Read cached data
552 552  
553 -== 2.10  Read or Clear cached data ==
474 +[[image:image-20220907154700-19.png]]
554 554  
555 555  
556 -(% style="color:#037691" %)**➢ AT Command:**
477 +AT+CDP=0 ~/~/ Clear cached data
557 557  
558 -* (% style="color:blue" %)**AT+CDP**        (%%) ~/~/  Read cached data
559 -* (% style="color:blue" %)**AT+CDP=0**    (%%) ~/~/  Clear cached data
560 560  
561 -[[image:image-20220907154700-19.png]]
480 +**2.11 Calibration**
562 562  
482 +User can do calibration for the probe. It is limited to use below pH buffer solution to calibrate: 4.00, 6.86, 9.18. When calibration, user need to clean the electrode and put the probe in the pH buffer solution to wait the value stable ( a new clean electrode might need max 24 hours to be stable).
563 563  
564 -== 2.11  Calibration ==
484 +After stable, user can use below command to calibrate.
565 565  
486 +[[image:image-20220907154700-20.png]] ​
566 566  
567 -User can do calibration for the probe. It is limited to use below pH buffer solution to calibrate: 4.00, 6.86, 9.18. When calibration, user need to clean the electrode and put the probe in the pH buffer solution to wait the value stable ( a new clean electrode might need max 24 hours to be stable).
488 +**2.8  ​Firmware Change Log**
568 568  
569 -After stable, user can use below command to calibrate.
490 +Download URL & Firmware Change log: [[https:~~/~~/www.dropbox.com/sh/1zmcakvbkf24f8x/AACmq2dZ3iRB9F1nVWeEB9Moa?dl=0>>url:https://www.dropbox.com/sh/1zmcakvbkf24f8x/AACmq2dZ3iRB9F1nVWeEB9Moa?dl=0]]
570 570  
492 +Upgrade Instruction: [[Upgrade Firmware>>path:#H5.1200BHowtoUpgradeFirmware]]
571 571  
572 -[[image:image-20220907154700-20.png]] ​
494 +**2.9  ​Battery Analysis**
573 573  
496 +**2.9.1  ​Battery Type**
574 574  
575 -== 2.12  ​Firmware Change Log ==
498 +The NSPH01 battery is a combination of an 8500mAh Li/SOCI2 Battery and a Super Capacitor. The battery is none-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
576 576  
500 +The battery is designed to last for several years depends on the actually use environment and update interval. 
577 577  
578 -Download URL & Firmware Change log: [[https:~~/~~/www.dropbox.com/sh/1tv07fro2pvjqj8/AAD-2wbfGfluTZfh38fQqdA_a?dl=0>>https://www.dropbox.com/sh/1tv07fro2pvjqj8/AAD-2wbfGfluTZfh38fQqdA_a?dl=0]]
502 +The battery related documents as below:
579 579  
580 -Upgrade Instruction: [[Upgrade Firmware>>||anchor="H5.1200BHowtoUpgradeFirmware"]]
504 +* [[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
505 +* [[Lithium-Thionyl Chloride Battery datasheet>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
506 +* [[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
581 581  
508 +[[image:image-20220907154700-21.png]] ​
582 582  
583 -== 2.13 Battery & Power Consumption ==
510 +**2.9.2  Power consumption Analyze**
584 584  
512 +Dragino battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
585 585  
586 -NSPH01 uses ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
514 +Instruction to use as below:
587 587  
588 -[[**Battery Info & Power Consumption Analyze**>>url:http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
516 +**Step 1:  **Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/]]
589 589  
518 +**Step 2: ** Open it and choose
590 590  
591 -= 3. ​ Access NB-IoT Module =
520 +* Product Model
521 +* Uplink Interval
522 +* Working Mode
592 592  
524 +And the Life expectation in difference case will be shown on the right.
593 593  
526 +(% style="text-align:center" %)
527 +[[image:image-20220907154700-22.jpeg]]
528 +
529 +​
530 +
531 +**2.9.3  ​Battery Note**
532 +
533 +The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
534 +
535 +**2.9.4  Replace the battery**
536 +
537 +The default battery pack of NSPH01 includes a ER26500 plus super capacitor. If user can't find this pack locally, they can find ER26500 or equivalence without the SPC1520 capacitor, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes).
538 +
539 +**3. ​ Access NB-IoT Module**
540 +
594 594  Users can directly access the AT command set of the NB-IoT module.
595 595  
596 596  The AT Command set can refer the BC35-G NB-IoT Module AT Command: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/]] 
597 597  
598 -
545 +(% style="text-align:center" %)
599 599  [[image:image-20220907154700-23.png]]
600 600  
601 601  ​
602 602  
603 -= 4.  Using the AT Commands =
550 +**4.  Using the AT Commands**
604 604  
605 -== 4.1  Access AT Commands ==
552 +**4.1  Access AT Commands**
606 606  
607 -
608 608  See this link for detail:  [[https:~~/~~/www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0>>url:https://www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0]]
609 609  
610 610  AT+<CMD>?  : Help on <CMD>
... ... @@ -615,9 +615,8 @@
615 615  
616 616  AT+<CMD>=?  : Get the value
617 617  
564 +**General Commands**      
618 618  
619 -(% style="color:#037691" %)**General Commands**      
620 -
621 621  AT  : Attention       
622 622  
623 623  AT?  : Short Help     
... ... @@ -642,18 +642,13 @@
642 642  
643 643  AT+TR      : Get or Set record time"
644 644  
645 -AT+APN     : Get or set the APN
646 646  
647 -AT+FBAND   : Get or Set whether to automatically modify the frequency band
648 -
649 -AT+DNSCFG  : Get or Set DNS Server
650 -
651 -AT+GETSENSORVALUE   : Returns the current sensor measurement
652 -
653 653  AT+NOUD      : Get or Set the number of data to be uploaded
654 654  
593 +
655 655  AT+CDP     : Read or Clear cached data
656 656  
596 +
657 657  AT+TEMPALARM      : Get or Set alarm of temp
658 658  
659 659  AT+PHALARM     : Get or Set alarm of PH
... ... @@ -661,18 +661,16 @@
661 661  AT+ PHCAL  : calibrate PH value
662 662  
663 663  
664 -(% style="color:#037691" %)**COAP Management**      
604 +**COAP Management**      
665 665  
666 666  AT+URI            : Resource parameters
667 667  
608 +**UDP Management**
668 668  
669 -(% style="color:#037691" %)**UDP Management**
670 -
671 671  AT+CFM          : Upload confirmation mode (only valid for UDP)
672 672  
612 +**MQTT Management**
673 673  
674 -(% style="color:#037691" %)**MQTT Management**
675 -
676 676  AT+CLIENT               : Get or Set MQTT client
677 677  
678 678  AT+UNAME  : Get or Set MQTT Username
... ... @@ -683,71 +683,54 @@
683 683  
684 684  AT+SUBTOPIC  : Get or Set MQTT subscription topic
685 685  
624 +**Information**          
686 686  
687 -(% style="color:#037691" %)**Information**          
688 -
689 689  AT+FDR  : Factory Data Reset
690 690  
691 691  AT+PWORD  : Serial Access Password
692 692  
630 +**​5.  FAQ**
693 693  
694 -= ​5.  FAQ =
632 +**5.1 ​ How to Upgrade Firmware**
695 695  
696 -== 5.1 ​ How to Upgrade Firmware ==
697 -
698 -
699 699  User can upgrade the firmware for 1) bug fix, 2) new feature release.
700 700  
701 701  Please see this link for how to upgrade:  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList]]
702 702  
703 -(% style="color:red" %)**Notice, NSPH01 and LSPH01 share the same mother board. They use the same connection and method to update.**
638 +**Notice, **NSPH01 **and **NSPH01 **share the same mother board. They use the same connection and method to update.**
704 704  
640 +**5.2  Can I calibrate NSPH01 to different soil types?**
705 705  
706 -== 5.2  Can I calibrate NSPH01 to different soil types? ==
707 -
708 -
709 709  NSPH01 is calibrated for saline-alkali soil and loamy soil. If users want to use it for other soil, they can calibrate the value in the IoT platform base on the value measured by saline-alkali soil and loamy soil. The formula can be found at [[this link>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/LSE01/Calibrate_to_other_Soil_20220605.pdf]].
710 710  
644 +**6.  Trouble Shooting**
711 711  
712 -= 6.  Trouble Shooting =
646 +**6.1  ​Connection problem when uploading firmware**
713 713  
714 -== 6.1  ​Connection problem when uploading firmware ==
715 -
716 -
717 717  **Please see: **[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting]]
718 718  
650 +**6.2  AT Command input doesn't work**
719 719  
720 -== 6.2  AT Command input doesn't work ==
652 +In the case if user can see the console output but can't type input to the device. Please check if you already include the **ENTER** while sending out the command. Some serial tool doesn't send **ENTER** while press the send key, user need to add ENTER in their string.
721 721  
654 +**7. ​ Order Info**
722 722  
723 -In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER** (%%)while press the send key, user need to add ENTER in their string.
724 -
725 -
726 -= 7. ​ Order Info =
727 -
728 -
729 729  Part Number**:** NSPH01
730 730  
658 +**8.  Packing Info**
731 731  
732 -
733 -= 8.  Packing Info =
734 -
735 -
736 736  **Package Includes**:
737 737  
738 -* NSPH01 NB-IoT pH Sensor x 1
662 +* NSPH01 NB-IoT Soil Moisture & EC Sensor x 1
739 739  * External antenna x 1
740 740  
741 741  **Dimension and weight**:
742 742  
743 -* Device Size: cm
744 -* Device Weight: g
745 -* Package Size / pcs : cm
746 -* Weight / pcs : g
667 +* Size: 195 x 125 x 55 mm
668 +* Weight:   420g
747 747  
748 -= 9.  Support =
670 +**9.  Support**
749 749  
750 -
751 751  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
752 752  * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]
753 753  
image-20220912144017-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -149.6 KB
Content
image-20220923101327-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -12.1 KB
Content
image-20221009000933-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Edwin
Size
... ... @@ -1,1 +1,0 @@
1 -282.9 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0