Last modified by Bei Jinggeng on 2024/03/30 17:53
<
From version < 56.20 >
edited by Xiaoling
on 2024/01/18 13:47
To version < 53.1 >
edited by David Huang
on 2022/10/08 11:47
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Xiaoling
1 +XWiki.David
Content
... ... @@ -9,34 +9,20 @@
9 9  
10 10  = 1.  Introduction =
11 11  
12 +
12 12  == 1.1 ​ What is NSPH01 Soil pH Sensor ==
13 13  
14 14  
15 -(((
16 16  The Dragino NSPH01 is a (% style="color:blue" %)**NB-IoT soil pH sensor**(%%) for IoT of Agriculture. It is designed to measure the soil pH and soil temperature, so to send to the platform to analyze the soil acid or alkali level. The probe is IP68 waterproof.
17 -)))
18 18  
19 -(((
20 20  NSPH01 probe is made by Solid AgCl reference electrode and Pure metal pH sensitive electrode. It can detect soil's** (% style="color:blue" %)pH (%%)**with high accuracy and stable value. The NSPH01 probe can be buried into soil for long time use.
21 -)))
22 22  
23 -(((
24 24  NarrowBand-Internet of Things (NB-IoT) is a standards-based low power wide area (LPWA) technology developed to enable a wide range of new IoT devices and services. NB-IoT significantly improves the power consumption of user devices, system capacity and spectrum efficiency, especially in deep coverage.
25 -)))
21 +\\NSPH01 supports different uplink methods include (% style="color:blue" %)**TCP,MQTT,UDP and CoAP  **(%%)for different application requirement.
22 +\\NSPH01 is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), It is designed for long term use up to 5 years. (Actually Battery life depends on the use environment, update period & uplink method)
23 +\\To use NSPH01, user needs to check if there is NB-IoT coverage in the installation area and with the bands NSPH01 supports. If the local operator supports it, user needs to get a (% style="color:blue" %)**NB-IoT SIM card** (%%)from local operator and install NSPH01 to get NB-IoT network connection.
26 26  
27 -(((
28 -NSPH01 supports different uplink methods include (% style="color:blue" %)**TCP,MQTT,UDP and CoAP  **(%%)for different application requirement.
29 -)))
30 30  
31 -(((
32 -NSPH01 is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), It is designed for long term use up to 5 years. (Actually Battery life depends on the use environment, update period & uplink method)
33 -)))
34 -
35 -(((
36 -To use NSPH01, user needs to check if there is NB-IoT coverage in the installation area and with the bands NSPH01 supports. If the local operator supports it, user needs to get a (% style="color:blue" %)**NB-IoT SIM card** (%%)from local operator and install NSPH01 to get NB-IoT network connection.
37 -)))
38 -
39 -
40 40  [[image:image-20220907153151-1.png]]
41 41  
42 42  
... ... @@ -43,6 +43,7 @@
43 43  [[image:M_K`YF9`CAYAE\@}3T]FHT$9.png]]
44 44  
45 45  
32 +
46 46  == 1.2  Features ==
47 47  
48 48  
... ... @@ -72,12 +72,12 @@
72 72  
73 73  (% style="color:#037691" %)**NB-IoT Spec:**
74 74  
75 -* B1 @H-FDD: 2100MHz
76 -* B3 @H-FDD: 1800MHz
77 -* B8 @H-FDD: 900MHz
78 -* B5 @H-FDD: 850MHz
79 -* B20 @H-FDD: 800MHz
80 -* B28 @H-FDD: 700MHz
62 +* - B1 @H-FDD: 2100MHz
63 +* - B3 @H-FDD: 1800MHz
64 +* - B8 @H-FDD: 900MHz
65 +* - B5 @H-FDD: 850MHz
66 +* - B20 @H-FDD: 800MHz
67 +* - B28 @H-FDD: 700MHz
81 81  
82 82  
83 83  == 1.4  Probe Specification ==
... ... @@ -113,8 +113,10 @@
113 113  [[image:image-20220907153300-2.png]]
114 114  
115 115  
103 +
116 116  = 2.  Use NSPH01 to communicate with IoT Server =
117 117  
106 +
118 118  == 2.1  How it works ==
119 119  
120 120  
... ... @@ -126,8 +126,10 @@
126 126  [[image:image-20220907153416-3.png]]
127 127  
128 128  
118 +
129 129  == 2.2 ​ Configure the NSPH01 ==
130 130  
121 +
131 131  === 2.2.1 Test Requirement ===
132 132  
133 133  
... ... @@ -137,6 +137,7 @@
137 137  * The local NB-IoT network used the band that NSPH01 supports.
138 138  * Your operator is able to distribute the data received in their NB-IoT network to your IoT server.
139 139  
131 +
140 140  Below figure shows our testing structure. Here we have NB-IoT network coverage by China Mobile, the band they use is B8.  The NSPH01 will use** CoAP(120.24.4.116:5683) **or raw **UDP(120.24.4.116:5601)** or **MQTT(120.24.4.116:1883)**or **TCP(120.24.4.116:5600)**protocol to send data to the test server.
141 141  
142 142  
... ... @@ -143,6 +143,7 @@
143 143  [[image:image-20220907153445-4.png]]
144 144  
145 145  
138 +
146 146  === 2.2.2 Insert SIM card ===
147 147  
148 148  
... ... @@ -152,6 +152,7 @@
152 152  [[image:image-20220907153505-5.png]]
153 153  
154 154  
148 +
155 155  === 2.2.3 Connect USB – TTL to NSPH01 to configure it ===
156 156  
157 157  
... ... @@ -175,13 +175,17 @@
175 175  * Parity:  (% style="color:green" %)**None**
176 176  * Flow Control: (% style="color:green" %)**None**
177 177  
172 +
178 178  Make sure the switch is in FLASH position, then power on device by connecting the jumper on NSPH01. NSPH01 will output system info once power on as below, we can enter the (% style="color:green" %)**password: 12345678**(%%) to access AT Command input.
179 179  
175 +
180 180  [[image:image-20220912144017-1.png]]
181 181  
178 +
182 182  (% style="color:red" %)**Note: the valid AT Commands can be found at:**(%%)**  **[[**https:~~/~~/www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0**>>url:https://www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0]]
183 183  
184 184  
182 +
185 185  === 2.2.4 Use CoAP protocol to uplink data ===
186 186  
187 187  
... ... @@ -206,6 +206,7 @@
206 206  [[image:image-20220907153612-8.png||height="529" width="729"]]
207 207  
208 208  
207 +
209 209  === 2.2.5 Use UDP protocol to uplink data(Default protocol) ===
210 210  
211 211  
... ... @@ -215,6 +215,7 @@
215 215  * (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5601   ** (%%) ~/~/  to set UDP server address and port
216 216  * (% style="color:blue" %)**AT+CFM=1       ** (%%) ~/~/  If the server does not respond, this command is unnecessar
217 217  
217 +
218 218  [[image:image-20220907153643-9.png||height="401" width="734"]]
219 219  
220 220  
... ... @@ -221,6 +221,7 @@
221 221  [[image:image-20220907153703-10.png||height="309" width="738"]]
222 222  
223 223  
224 +
224 224  === 2.2.6 Use MQTT protocol to uplink data ===
225 225  
226 226  
... ... @@ -234,6 +234,7 @@
234 234  * (% style="color:blue" %)**AT+PUBTOPIC=NSE01_PUB                    **(%%)~/~/ Set the sending topic of MQTT
235 235  * (% style="color:blue" %)**AT+SUBTOPIC=NSE01_SUB          ** (%%) ~/~/ Set the subscription topic of MQTT
236 236  
238 +
237 237  [[image:image-20220907153739-11.png||height="491" width="764"]]
238 238  
239 239  
... ... @@ -243,6 +243,8 @@
243 243  MQTT protocol has a much higher power consumption compare vs UDP / CoAP protocol. Please check the power analyze document and adjust the uplink period to a suitable interval.
244 244  
245 245  
248 +
249 +
246 246  === 2.2.7 Use TCP protocol to uplink data ===
247 247  
248 248  
... ... @@ -251,6 +251,7 @@
251 251  * (% style="color:blue" %)**AT+PRO=4   ** (%%) ~/~/ Set to use TCP protocol to uplink
252 252  * (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5600   ** (%%) ~/~/ to set TCP server address and port
253 253  
258 +
254 254  [[image:image-20220907153818-13.png||height="486" width="668"]]
255 255  
256 256  
... ... @@ -257,6 +257,7 @@
257 257  [[image:image-20220907153827-14.png||height="236" width="684"]]
258 258  
259 259  
265 +
260 260  === 2.2.8 Change Update Interval ===
261 261  
262 262  
... ... @@ -267,6 +267,7 @@
267 267  (% style="color:red" %)**NOTE: By default, the device will send an uplink message every 2 hours. Each Uplink Include 8 set of records in this 2 hour (15 minute interval / record).**
268 268  
269 269  
276 +
270 270  == 2.3  Uplink Payload ==
271 271  
272 272  
... ... @@ -274,9 +274,9 @@
274 274  
275 275  Each time the device uploads a data package, 8 sets of recorded data will be attached. Up to 32 sets of recorded data can be uploaded.
276 276  
277 -(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:515px" %)
278 -|(% style="background-color:#4F81BD;color:white; width:50px" %)**Size(bytes)**|(% style="background-color:#4F81BD;color:white; width:40px" %)**8**|(% style="background-color:#4F81BD;color:white; width:20px" %)**2**|(% style="background-color:#4F81BD;color:white; width:25px" %)**2**|(% style="background-color:#4F81BD;color:white; width:60px" %)**1**|(% style="background-color:#4F81BD;color:white; color:#0070c0; width:20px" %)**1**|(% style="background-color:#4F81BD;color:white; width:40px" %)**1**|(% style="background-color:#4F81BD;color:white; width:40px" %)**2**|(% style="background-color:#4F81BD;color:white; width:49px" %)**2**|(% style="background-color:#4F81BD;color:white; width:49px" %)**4**|(% style="background-color:#4F81BD;color:white; width:49px" %)**2**|(% style="background-color:#4F81BD;color:white; width:34px" %)**2**|(% style="background-color:#4F81BD;color:white; width:39px" %)**4**
279 -|(% style="width:96px" %)Value|(% style="width:83px" %)Device ID|(% style="width:44px" %)Ver|(% style="width:42px" %)BAT|(% style="width:124px" %)Signal Strength|(% style="width:57px" %)MOD|(% style="width:80px" %)Interrupt|(% style="width:69px" %)Soil PH|(% style="width:134px" %)Soil Temperature|(% style="width:98px" %)Time stamp|(% style="width:134px" %)Soil Temperature|(% style="width:68px" %)Soil PH|(% style="width:125px" %)Time stamp  .....
284 +(% border="2" style="background-color:#ffffcc; color:green; width:1160px" %)
285 +|(% style="width:96px" %)**Size(bytes)**|(% style="width:83px" %)**8**|(% style="width:44px" %)**2**|(% style="width:42px" %)**2**|(% style="width:124px" %)1|(% style="width:57px" %)1|(% style="width:80px" %)1|(% style="width:69px" %)2|(% style="width:134px" %)2|(% style="width:98px" %)4|(% style="width:134px" %)2|(% style="width:68px" %)2|(% style="width:125px" %)4
286 +|(% style="width:96px" %)**Value**|(% style="width:83px" %)Device ID|(% style="width:44px" %)Ver|(% style="width:42px" %)BAT|(% style="width:124px" %)Signal Strength|(% style="width:57px" %)MOD|(% style="width:80px" %)Interrupt|(% style="width:69px" %)Soil PH|(% style="width:134px" %)Soil Temperature|(% style="width:98px" %)Time stamp|(% style="width:134px" %)Soil Temperature|(% style="width:68px" %)Soil PH|(% style="width:125px" %)Time stamp  .....
280 280  
281 281  If we use the MQTT client to subscribe to this MQTT topic, we can see the following information when the NSPH01 uplink data.
282 282  
... ... @@ -298,34 +298,26 @@
298 298  (((
299 299  
300 300  
301 -**where:**
308 +where:
302 302  )))
303 303  
304 -* (% style="color:#037691" %)**Device ID:**(%%)** **0xf868411056754138 = f868411056754138
311 +* Device ID: 0xf868411056754138 = f868411056754138
312 +* Version:  0x0064=100=1.0.0
313 +* BAT:  0x0c78 = 3192 mV = 3.192V
314 +* Singal: 0x17 = 23
315 +* Mod:  0x01 = 1
316 +* Interrupt: 0x00= 0
317 +* Soil PH:  0x0225= 549 = 5.49
318 +* Soil Temperature: 0x010b =267=26.7 °C
319 +* Time stamp :  0x6315537b =1662342011  ([[Unix Epoch Time>>url:http://www.epochconverter.com/]])
320 +* Soil Temperature,Soil PH,Time stamp :  010b0226631550fb
321 +* 8 sets of recorded data: Temperature,Soil PH,Time stamp :  010e022663154d77,.......
305 305  
306 -* (% style="color:#037691" %)**Version:**  (%%) 0x0064=100=1.0.0
307 307  
308 -* (% style="color:#037691" %)**BAT:**   (%%) 0x0c78 = 3192 mV = 3.192V
309 309  
310 -* (% style="color:#037691" %)**Singal:** (%%)0x17 = 23
311 -
312 -* (% style="color:#037691" %)**Mod:** (%%) 0x01 = 1
313 -
314 -* (% style="color:#037691" %)**Interrupt:**(%%) 0x00= 0
315 -
316 -* (% style="color:#037691" %)**Soil PH:** (%%) 0x0225= 549 = 5.49
317 -
318 -* (% style="color:#037691" %)**Soil Temperature:**(%%) 0x010b =267=26.7 °C
319 -
320 -* (% style="color:#037691" %)**Time stamp :**   (%%) 0x6315537b =1662342011  ([[Unix Epoch Time>>url:http://www.epochconverter.com/]])
321 -
322 -* (% style="color:#037691" %)**Soil Temperature,Soil PH,Time stamp : **(%%) 010b0226631550fb
323 -
324 -* (% style="color:#037691" %)**8 sets of recorded data:**(%%) Temperature,Soil PH,Time stamp :  010e022663154d77,.......
325 -
326 -
327 327  == 2.4  Payload Explanation and Sensor Interface ==
328 328  
327 +
329 329  === 2.4.1  Device ID ===
330 330  
331 331  
... ... @@ -341,6 +341,7 @@
341 341  The Device ID is stored in a none-erase area, Upgrade the firmware or run AT+FDR won't erase Device ID.
342 342  
343 343  
343 +
344 344  === 2.4.2  Version Info ===
345 345  
346 346  
... ... @@ -349,6 +349,7 @@
349 349  For example: 0x00 64 : this device is NSPH01 with firmware version 1.0.0.
350 350  
351 351  
352 +
352 352  === 2.4.3  Battery Info ===
353 353  
354 354  
... ... @@ -359,6 +359,7 @@
359 359  Ex2: 0x0B49 = 2889mV
360 360  
361 361  
363 +
362 362  === 2.4.4  Signal Strength ===
363 363  
364 364  
... ... @@ -377,6 +377,7 @@
377 377  **99**    Not known or not detectable
378 378  
379 379  
382 +
380 380  === 2.4.5  Soil PH ===
381 381  
382 382  
... ... @@ -387,6 +387,7 @@
387 387  (% style="color:blue" %)**0229(H) = 549(D) /100 = 5.49.**
388 388  
389 389  
393 +
390 390  === 2.4.6  Soil Temperature ===
391 391  
392 392  
... ... @@ -400,6 +400,7 @@
400 400  If payload is FF7EH: ((FF7E & 0x8000)>>15 ===1),temp = (FF7E(H)-FFFF(H))/10 = -12.9 °C
401 401  
402 402  
407 +
403 403  === 2.4.7  Timestamp ===
404 404  
405 405  
... ... @@ -408,6 +408,7 @@
408 408  Convert Unix timestamp to time 2022-9-5 9:40:11.
409 409  
410 410  
416 +
411 411  === 2.4.8  Digital Interrupt ===
412 412  
413 413  
... ... @@ -427,6 +427,7 @@
427 427  0x(01): Interrupt Uplink Packet.
428 428  
429 429  
436 +
430 430  === 2.4.9  ​+5V Output ===
431 431  
432 432  
... ... @@ -439,17 +439,15 @@
439 439  Means set 5V valid time to have 1000ms. So the real 5V output will actually have 1000ms + sampling time for other sensors.** **
440 440  
441 441  
449 +
442 442  == 2.5  Downlink Payload ==
443 443  
444 444  
445 445  By default, NSPH01 prints the downlink payload to console port.
446 446  
447 -(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:479.818px" %)
448 -|=(% style="width: 183px; background-color:#D9E2F3;color:#0070C0" %)**Downlink Control Type**|=(% style="width: 55px; background-color:#D9E2F3;color:#0070C0" %)FPort|=(% style="width: 93px; background-color:#D9E2F3;color:#0070C0" %)**Type Code**|=(% style="width: 146px; background-color: rgb(217, 226, 243); color: rgb(0, 112, 192);" %)**Downlink payload size(bytes)**
449 -|(% style="width:183px" %)TDC (Transmit Time Interval)|(% style="width:55px" %)Any|(% style="width:93px" %)01|(% style="width:146px" %)4
450 -|(% style="width:183px" %)RESET|(% style="width:55px" %)Any|(% style="width:93px" %)04|(% style="width:146px" %)2
451 -|(% style="width:183px" %)INTMOD|(% style="width:55px" %)Any|(% style="width:93px" %)06|(% style="width:146px" %)4
455 +[[image:image-20220907154636-17.png]]
452 452  
457 +
453 453  (% style="color:blue" %)**Examples:**
454 454  
455 455  * (% style="color:#037691" %)** Set TDC**
... ... @@ -469,6 +469,7 @@
469 469  Downlink Payload: 06000003, Set AT+INTMOD=3
470 470  
471 471  
477 +
472 472  == 2.6  ​LED Indicator ==
473 473  
474 474  
... ... @@ -480,8 +480,10 @@
480 480  * For each uplink probe, LED will be on for 500ms.
481 481  
482 482  
489 +
483 483  == 2.7  Installation and Maintain ==
484 484  
492 +
485 485  === 2.7.1  Before measurement ===
486 486  
487 487  
... ... @@ -488,6 +488,7 @@
488 488  If the NSPH01 has more than 7 days not use or just clean the pH probe. User should put the probe inside pure water for more than 24 hours for activation. If no put in water, user need to put inside soil for more than 24 hours to ensure the measurement accuracy. 
489 489  
490 490  
499 +
491 491  === 2.7.2  Measurement ===
492 492  
493 493  
... ... @@ -512,6 +512,7 @@
512 512  Insert the probe inside, method like measure the surface.
513 513  
514 514  
524 +
515 515  === 2.7.3  Maintain Probe ===
516 516  
517 517  
... ... @@ -523,6 +523,7 @@
523 523  1. The probe is IP68 can be put in water.
524 524  
525 525  
536 +
526 526  == 2.8  PH and Temperature alarm function ==
527 527  
528 528  
... ... @@ -555,6 +555,7 @@
555 555  AT+ TEMPALARM=20,30  ~/~/ Alarm when temperature lower than 20.
556 556  
557 557  
569 +
558 558  == 2.9  Set the number of data to be uploaded and the recording time ==
559 559  
560 560  
... ... @@ -563,11 +563,9 @@
563 563  * (% style="color:blue" %)**AT+TR=900**     (%%) ~/~/  The unit is seconds, and the default is to record data once every 900 seconds.( The minimum can be set to 180 seconds)
564 564  * (% style="color:blue" %)**AT+NOUD=8**     (%%) ~/~/  The device uploads 8 sets of recorded data by default. Up to 32 sets of record data can be uploaded.
565 565  
566 - The diagram below explains the relationship between TR, NOUD, and TDC more clearly**:**
567 567  
568 -[[image:image-20221009000933-1.png||height="750" width="1043"]]
579 +This link explains the relationship between TR, NOUD and TDC more clearly** : **[[https:~~/~~/www.processon.com/view/link/6340e606e401fd390891af87>>url:https://www.processon.com/view/link/6340e606e401fd390891af87]]
569 569  
570 -
571 571  == 2.10  Read or Clear cached data ==
572 572  
573 573  
... ... @@ -576,9 +576,11 @@
576 576  * (% style="color:blue" %)**AT+CDP**        (%%) ~/~/  Read cached data
577 577  * (% style="color:blue" %)**AT+CDP=0**    (%%) ~/~/  Clear cached data
578 578  
589 +
579 579  [[image:image-20220907154700-19.png]]
580 580  
581 581  
593 +
582 582  == 2.11  Calibration ==
583 583  
584 584  
... ... @@ -586,34 +586,11 @@
586 586  
587 587  After stable, user can use below command to calibrate.
588 588  
589 -(% border="1" cellspacing="3" style="background-color:#f2f2f2; width:515px" %)
590 -|(% style="background-color:#4F81BD;color:white; width:118px" %)**pH buffer solution**|(% style="background-color:#4F81BD;color:white; width:149px" %)**AT Command to calibrate**|(% style="background-color:#4F81BD;color:white; width:149px" %)**Downlink Command**|(% style="background-color:#4F81BD;color:white; width:99px" %)**Read Cal Value**
591 -|(% style="width:149px" %)4.00|(% style="width:197px" %)AT+PHCAL=4|(% style="width:206px" %)(((
592 -0x13 04
593 -Reply with Calibrate payload
594 -)))|(% style="width:136px" %)(((
595 -AT+PHCAL=?
596 -Example 41,61,91
597 -)))
598 -|(% style="width:149px" %)6.86|(% style="width:197px" %)AT+PHCAL=6|(% style="width:206px" %)(((
599 -0x13 06
600 -Reply with Calibrate payload
601 -)))|(% style="width:136px" %)AT+PHCAL=?
602 -|(% style="width:149px" %)9.18|(% style="width:197px" %)AT+PHCAL=9|(% style="width:206px" %)(((
603 -0x13 09
604 -Reply with Calibrate payload
605 -)))|(% style="width:136px" %)AT+PHCAL=?
606 -|(% style="width:149px" %)Factory Default|(% style="width:197px" %)AT+PHCAL=15|(% style="width:206px" %)(((
607 -0x13 15
608 -Reply with Calibrate payload
609 -)))|(% style="width:136px" %)(((
610 -AT+PHCAL=?
611 -Example 151
612 -)))
613 613  
614 - ​
602 +[[image:image-20220907154700-20.png]] ​
615 615  
616 616  
605 +
617 617  == 2.12  ​Firmware Change Log ==
618 618  
619 619  
... ... @@ -622,14 +622,64 @@
622 622  Upgrade Instruction: [[Upgrade Firmware>>||anchor="H5.1200BHowtoUpgradeFirmware"]]
623 623  
624 624  
625 -== 2.13 Battery & Power Consumption ==
626 626  
615 +== 2.13  ​Battery Analysis ==
627 627  
628 -NSPH01 uses ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
629 629  
630 -[[**Battery Info & Power Consumption Analyze**>>url:http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
618 +=== 2.13.1  ​Battery Type ===
631 631  
632 632  
621 +The NSPH01 battery is a combination of an 8500mAh Li/SOCI2 Battery and a Super Capacitor. The battery is none-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
622 +
623 +The battery is designed to last for several years depends on the actually use environment and update interval. 
624 +
625 +The battery-related documents as below:
626 +
627 +* [[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
628 +* [[Lithium-Thionyl Chloride Battery datasheet>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
629 +* [[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
630 +
631 +[[image:image-20220907154700-21.png]] ​
632 +
633 +
634 +
635 +=== 2.13.2  Power consumption Analyze ===
636 +
637 +
638 +Dragino battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
639 +
640 +Instruction to use as below:
641 +
642 +(% style="color:blue" %)**Step 1:  **(%%)Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/]]
643 +
644 +(% style="color:blue" %)**Step 2: **(%%) Open it and choose
645 +
646 +* Product Model
647 +* Uplink Interval
648 +* Working Mode
649 +
650 +And the Life expectation in difference case will be shown on the right.
651 +
652 +
653 +[[image:image-20220907154700-22.jpeg]]
654 +
655 +​
656 +
657 +
658 +=== 2.13.3  ​Battery Note ===
659 +
660 +
661 +The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
662 +
663 +
664 +
665 +=== 2.13.4  Replace the battery ===
666 +
667 +
668 +The default battery pack of NSPH01 includes a ER26500 plus super capacitor. If user can't find this pack locally, they can find ER26500 or equivalence without the SPC1520 capacitor, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes).
669 +
670 +
671 +
633 633  = 3. ​ Access NB-IoT Module =
634 634  
635 635  
... ... @@ -642,8 +642,10 @@
642 642  
643 643  ​
644 644  
684 +
645 645  = 4.  Using the AT Commands =
646 646  
687 +
647 647  == 4.1  Access AT Commands ==
648 648  
649 649  
... ... @@ -733,8 +733,10 @@
733 733  AT+PWORD  : Serial Access Password
734 734  
735 735  
777 +
736 736  = ​5.  FAQ =
737 737  
780 +
738 738  == 5.1 ​ How to Upgrade Firmware ==
739 739  
740 740  
... ... @@ -745,6 +745,7 @@
745 745  (% style="color:red" %)**Notice, NSPH01 and LSPH01 share the same mother board. They use the same connection and method to update.**
746 746  
747 747  
791 +
748 748  == 5.2  Can I calibrate NSPH01 to different soil types? ==
749 749  
750 750  
... ... @@ -751,8 +751,10 @@
751 751  NSPH01 is calibrated for saline-alkali soil and loamy soil. If users want to use it for other soil, they can calibrate the value in the IoT platform base on the value measured by saline-alkali soil and loamy soil. The formula can be found at [[this link>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/LSE01/Calibrate_to_other_Soil_20220605.pdf]].
752 752  
753 753  
798 +
754 754  = 6.  Trouble Shooting =
755 755  
801 +
756 756  == 6.1  ​Connection problem when uploading firmware ==
757 757  
758 758  
... ... @@ -759,6 +759,7 @@
759 759  **Please see: **[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting]]
760 760  
761 761  
808 +
762 762  == 6.2  AT Command input doesn't work ==
763 763  
764 764  
... ... @@ -765,12 +765,7 @@
765 765  In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER** (%%)while press the send key, user need to add ENTER in their string.
766 766  
767 767  
768 -== 6.3 Not able to connect to NB-IoT network and keep showing "Signal Strength:99". ==
769 769  
770 -
771 -This means sensor is trying to join the NB-IoT network but fail. Please see this link for **//[[trouble shooting for signal strenght:99>>doc:Main.CSQ\:99,99.WebHome]]//**.
772 -
773 -
774 774  = 7. ​ Order Info =
775 775  
776 776  
... ... @@ -777,6 +777,7 @@
777 777  Part Number**:** NSPH01
778 778  
779 779  
822 +
780 780  = 8.  Packing Info =
781 781  
782 782  
... ... @@ -793,6 +793,7 @@
793 793  * Weight / pcs : g
794 794  
795 795  
839 +
796 796  = 9.  Support =
797 797  
798 798  
image-20221009000933-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Edwin
Size
... ... @@ -1,1 +1,0 @@
1 -282.9 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0