Last modified by Bei Jinggeng on 2024/03/30 17:53
<
From version < 45.1 >
edited by David Huang
on 2022/09/07 17:57
To version < 56.9 >
edited by Xiaoling
on 2023/04/04 08:50
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.David
1 +XWiki.Xiaoling
Content
... ... @@ -1,5 +1,5 @@
1 1  (% style="text-align:center" %)
2 -[[image:)YK]Y_LZJIO]J2~~VA}OQJM2.png]]
2 +[[image:)YK]Y_LZJIO]J2~~VA}OQJM2.png||height="442" width="410"]]
3 3  
4 4  **Table of Contents:**
5 5  
... ... @@ -7,31 +7,37 @@
7 7  
8 8  
9 9  
10 -= 1. Introduction =
10 += 1.  Introduction =
11 11  
12 -== 1.1 ​What is NSPH01 Soil pH Sensor ==
12 +== 1.1 ​ What is NSPH01 Soil pH Sensor ==
13 13  
14 -The Dragino NSPH01 is a **NB-IOT soil ph sensor** for IoT of Agriculture. It is designed to measure the soil PH and soil temperature, so to send to the platform to analyze the soil acid or alkali level. The probe is IP68 waterproof.
15 15  
16 -NSPH01 probe is made by Solid AgCl reference electrode and Pure metal pH sensitive electrode. It can detect soil's** pH **with high accuracy and stable value. The NSPH01 probe can be buried into soil for long time use.
15 +The Dragino NSPH01 is a (% style="color:blue" %)**NB-IoT soil pH sensor**(%%) for IoT of Agriculture. It is designed to measure the soil pH and soil temperature, so to send to the platform to analyze the soil acid or alkali level. The probe is IP68 waterproof.
17 17  
17 +NSPH01 probe is made by Solid AgCl reference electrode and Pure metal pH sensitive electrode. It can detect soil's** (% style="color:blue" %)pH (%%)**with high accuracy and stable value. The NSPH01 probe can be buried into soil for long time use.
18 +
18 18  NarrowBand-Internet of Things (NB-IoT) is a standards-based low power wide area (LPWA) technology developed to enable a wide range of new IoT devices and services. NB-IoT significantly improves the power consumption of user devices, system capacity and spectrum efficiency, especially in deep coverage.
19 -\\NSPH01 supports different uplink methods include **TCP,MQTT,UDP and CoAP  **for different application requirement.
20 -\\NSPH01 is powered by  **8500mAh Li-SOCI2 battery**, It is designed for long term use up to 5 years. (Actually Battery life depends on the use environment, update period & uplink method)
21 -\\To use NSPH01, user needs to check if there is NB-IoT coverage in local area and with the bands NSPH01 supports. If the local operate support it, user needs to get a **NB-IoT SIM card** from local operator and install NSPH01 to get NB-IoT network connection.
22 22  
23 -(% style="text-align:center" %)
21 +NSPH01 supports different uplink methods include (% style="color:blue" %)**TCP,MQTT,UDP and CoAP  **(%%)for different application requirement.
22 +
23 +NSPH01 is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), It is designed for long term use up to 5 years. (Actually Battery life depends on the use environment, update period & uplink method)
24 +
25 +To use NSPH01, user needs to check if there is NB-IoT coverage in the installation area and with the bands NSPH01 supports. If the local operator supports it, user needs to get a (% style="color:blue" %)**NB-IoT SIM card** (%%)from local operator and install NSPH01 to get NB-IoT network connection.
26 +
27 +
24 24  [[image:image-20220907153151-1.png]]
25 25  
26 -(% style="text-align:center" %)
30 +
27 27  [[image:M_K`YF9`CAYAE\@}3T]FHT$9.png]]
28 28  
29 -== 1.2 Features ==
30 30  
34 +== 1.2  Features ==
35 +
36 +
31 31  * NB-IoT Bands: B1/B3/B8/B5/B20/B28 @H-FDD
32 32  * Monitor soil pH with temperature compensation.
33 33  * Monitor soil temperature
34 -* PH and Temperature alarm function
40 +* pH and Temperature alarm function
35 35  * Monitor Battery Level
36 36  * Support pH calibration by end user
37 37  * Uplink on periodically
... ... @@ -40,29 +40,31 @@
40 40  * IP68 rate for the Sensor Probe
41 41  * Ultra-Low Power consumption
42 42  * AT Commands to change parameters
43 -* Micro SIM card slot for NB-IoT SIM
49 +* Micro SIM card slot
44 44  * 8500mAh Battery for long term use
45 45  
46 46  == 1.3  Specification ==
47 47  
48 -**Common DC Characteristics:**
49 49  
55 +(% style="color:#037691" %)**Common DC Characteristics:**
56 +
50 50  * Supply Voltage: 2.1v ~~ 3.6v
51 51  * Operating Temperature: -40 ~~ 85°C
52 52  
53 -**NB-IoT Spec:**
60 +(% style="color:#037691" %)**NB-IoT Spec:**
54 54  
55 -* - B1 @H-FDD: 2100MHz
56 -* - B3 @H-FDD: 1800MHz
57 -* - B8 @H-FDD: 900MHz
58 -* - B5 @H-FDD: 850MHz
59 -* - B20 @H-FDD: 800MHz
60 -* - B28 @H-FDD: 700MHz
62 +* B1 @H-FDD: 2100MHz
63 +* B3 @H-FDD: 1800MHz
64 +* B8 @H-FDD: 900MHz
65 +* B5 @H-FDD: 850MHz
66 +* B20 @H-FDD: 800MHz
67 +* B28 @H-FDD: 700MHz
61 61  
62 -== 1.4 Probe Specification ==
69 +== 1.4  Probe Specification ==
63 63  
64 -**Soil pH:**
65 65  
72 +(% style="color:#037691" %)**Soil pH:**
73 +
66 66  * Range: 3 ~~ 10 pH
67 67  * Resolution: 0.01 pH
68 68  * Accuracy: ±2% under (0~~50 ℃, Accuracy will poor under 0 due to frozen)
... ... @@ -70,7 +70,7 @@
70 70  * IP68 Protection
71 71  * Length: 3.5 meters
72 72  
73 -**Soil Temperature:**
81 +(% style="color:#037691" %)**Soil Temperature:**
74 74  
75 75  * Range -40℃～85℃
76 76  * Resolution: 0.1℃
... ... @@ -78,198 +78,241 @@
78 78  * IP68 Protection
79 79  * Length: 3.5 meters
80 80  
81 -== 1.5 ​Applications ==
89 +== 1.5  ​Applications ==
82 82  
91 +
83 83  * Smart Agriculture
84 84  
85 -== 1.6 Pin mapping and power on ==
94 +== 1.6  Pin mapping and power on ==
86 86  
87 -(% style="text-align:center" %)
96 +
88 88  [[image:image-20220907153300-2.png]]
89 89  
90 90  
100 +
91 91  = 2.  Use NSPH01 to communicate with IoT Server =
92 92  
93 93  == 2.1  How it works ==
94 94  
105 +
95 95  The NSPH01 is equipped with a NB-IoT module, the pre-loaded firmware in NSPH01 will get environment data from sensors and send the value to local NB-IoT network via the NB-IoT module.  The NB-IoT network will forward this value to IoT server via the protocol defined by NSPH01.
96 96  
97 97  The diagram below shows the working flow in default firmware of NSPH01:
98 98  
99 -(% style="text-align:center" %)
110 +
100 100  [[image:image-20220907153416-3.png]]
101 101  
113 +
114 +
102 102  == 2.2 ​ Configure the NSPH01 ==
103 103  
104 104  === 2.2.1 Test Requirement ===
105 105  
106 -To use NSPH01 in your city, make sure meet below requirements:
107 107  
120 +To use NSPH01 in the field, make sure meet below requirements:
121 +
108 108  * Your local operator has already distributed a NB-IoT Network there.
109 109  * The local NB-IoT network used the band that NSPH01 supports.
110 110  * Your operator is able to distribute the data received in their NB-IoT network to your IoT server.
111 111  
112 -Below figure shows our testing structure. Here we have NB-IoT network coverage by China Mobile, the band they use is B8.  The NSPH01 will use CoAP(120.24.4.116:5683) or raw UDP(120.24.4.116:5601) or MQTT(120.24.4.116:1883)or TCP(120.24.4.116:5600)protocol to send data to the test server
126 +Below figure shows our testing structure. Here we have NB-IoT network coverage by China Mobile, the band they use is B8.  The NSPH01 will use** CoAP(120.24.4.116:5683) **or raw **UDP(120.24.4.116:5601)** or **MQTT(120.24.4.116:1883)**or **TCP(120.24.4.116:5600)**protocol to send data to the test server.
113 113  
114 -(% style="text-align:center" %)
128 +
115 115  [[image:image-20220907153445-4.png]]
116 116  
117 117  
118 118  === 2.2.2 Insert SIM card ===
119 119  
120 -Insert the NB-IoT Card get from your provider.
121 121  
122 -User need to take out the NB-IoT module and insert the SIM card like below:
135 +User need to take out the NB-IoT module and insert the SIM card like below. ((% style="color:red" %) Pay attention to the direction(%%))
123 123  
124 -(% style="text-align:center" %)
137 +
125 125  [[image:image-20220907153505-5.png]]
126 126  
140 +
127 127  === 2.2.3 Connect USB – TTL to NSPH01 to configure it ===
128 128  
129 -User need to configure NSPH01 via serial port to set the **Server Address** / **Uplink Topic** to define where and how-to uplink packets. NSPH01 support AT Commands, user can use a USB to TTL adapter to connect to NSPH01 and use AT Commands to configure it, as below.
130 130  
131 -**Connection:**
144 +User need to configure NSPH01 via serial port to set the (% style="color:blue" %)**Server Address** / **Uplink Topic**(%%) to define where and how-to uplink packets. NSPH01 support AT Commands, user can use a USB to TTL adapter to connect to NSPH01 and use AT Commands to configure it, as below.
132 132  
133 - USB TTL GND <~-~-~-~-> GND
134 134  
135 - USB TTL TXD <~-~-~-~-> UART_RXD
147 +(% style="color:blue" %)**Connection:**
136 136  
137 - USB TTL RXD <~-~-~-~-> UART_TXD
149 +**~ (% style="background-color:yellow" %) USB TTL GND <~-~-~-~->  GND(%%)**
138 138  
151 +**~ (% style="background-color:yellow" %) USB TTL TXD  <~-~-~-~->  UART_RXD(%%)**
152 +
153 +**~ (% style="background-color:yellow" %) USB TTL RXD  <~-~-~-~->  UART_TXD(%%)**
154 +
155 +
139 139  In the PC, use below serial tool settings:
140 140  
141 -* Baud:  **9600**
142 -* Data bits:** 8**
143 -* Stop bits: **1**
144 -* Parity:  **None**
145 -* Flow Control: **None**
158 +* Baud:  (% style="color:green" %)**9600**
159 +* Data bits:**  (% style="color:green" %)8(%%)**
160 +* Stop bits:  (% style="color:green" %)**1**
161 +* Parity:  (% style="color:green" %)**None**
162 +* Flow Control: (% style="color:green" %)**None**
146 146  
147 -Make sure the switch is in FLASH position, then power on device by connecting the jumper on NSPH01. NSPH01 will output system info once power on as below, we can enter the **password: 12345678** to access AT Command input.
164 +Make sure the switch is in FLASH position, then power on device by connecting the jumper on NSPH01. NSPH01 will output system info once power on as below, we can enter the (% style="color:green" %)**password: 12345678**(%%) to access AT Command input.
148 148  
149 -(% style="text-align:center" %)
150 -[[image:image-20220907153529-6.png]]
151 151  
152 -**Note: the valid AT Commands can be found at:  **[[**https:~~/~~/www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0**>>url:https://www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0]]
167 +[[image:image-20220912144017-1.png]]
153 153  
169 +
170 +(% style="color:red" %)**Note: the valid AT Commands can be found at:**(%%)**  **[[**https:~~/~~/www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0**>>url:https://www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0]]
171 +
172 +
154 154  === 2.2.4 Use CoAP protocol to uplink data ===
155 155  
156 -**Note: if you don't have CoAP server, you can refer this link to set up one: **[[**http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/**>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/]]
157 157  
158 -**Use below commands:**
176 +(% style="color:red" %)**Note: if you don't have CoAP server, you can refer this link to set up one:**(%%)** **[[**http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/**>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/]]
159 159  
160 -* **AT+PRO=1**   ~/~/ Set to use CoAP protocol to uplink
161 -* **AT+SERVADDR=120.24.4.116,5683   ** ~/~/ to set CoAP server address and port
162 -* **AT+URI=5,11,"mqtt",11,"coap",12,"0",15,"c=text1",23,"0" ** ~/~/Set COAP resource path
163 163  
179 +(% style="color:blue" %)**Use below commands:**
180 +
181 +* (% style="color:#037691" %)**AT+PRO=1**                         (%%) ~/~/  Set to use CoAP protocol to uplink
182 +* (% style="color:#037691" %)**AT+SERVADDR=120.24.4.116,5683   ** (%%) ~/~/  to set CoAP server address and port
183 +* (% style="color:#037691" %)**AT+URI=5,11,"mqtt",11,"coap",12,"0",15,"c=text1",23,"0" ** (%%) ~/~/  Set COAP resource path
184 +
164 164  For parameter description, please refer to AT command set
165 165  
166 -(% style="text-align:center" %)
187 +
167 167  [[image:image-20220907153551-7.png||height="502" width="740"]]
168 168  
169 -After configure the server address and **reset the device** (via AT+ATZ ), NSPH01 will start to uplink sensor values to CoAP server.
170 170  
171 -(% style="text-align:center" %)
191 +After configure the server address and (% style="color:green" %)**reset the device (via AT+ATZ )**(%%), NSPH01 will start to uplink sensor values to CoAP server.
192 +
193 +
172 172  [[image:image-20220907153612-8.png||height="529" width="729"]]
173 173  
174 174  
175 175  === 2.2.5 Use UDP protocol to uplink data(Default protocol) ===
176 176  
199 +
177 177  This feature is supported since firmware version v1.0.1
178 178  
179 -* **AT+PRO=2   ** ~/~/ Set to use UDP protocol to uplink
180 -* **AT+SERVADDR=120.24.4.116,5601   ** ~/~/ to set UDP server address and port
181 -* **AT+CFM=1       ** ~/~/If the server does not respond, this command is unnecessar
202 +* (% style="color:blue" %)**AT+PRO=2   ** (%%) ~/~/  Set to use UDP protocol to uplink
203 +* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5601   ** (%%) ~/~/  to set UDP server address and port
204 +* (% style="color:blue" %)**AT+CFM=1       ** (%%) ~/~/  If the server does not respond, this command is unnecessar
182 182  
183 -(% style="text-align:center" %)
184 184  [[image:image-20220907153643-9.png||height="401" width="734"]]
185 185  
186 -(% style="text-align:center" %)
208 +
187 187  [[image:image-20220907153703-10.png||height="309" width="738"]]
188 188  
189 189  
190 190  === 2.2.6 Use MQTT protocol to uplink data ===
191 191  
214 +
192 192  This feature is supported since firmware version v110
193 193  
194 -* **AT+PRO=3   ** ~/~/Set to use MQTT protocol to uplink
195 -* **AT+SERVADDR=120.24.4.116,1883   ** ~/~/Set MQTT server address and port
196 -* **AT+CLIENT=CLIENT       ** ~/~/Set up the CLIENT of MQTT
197 -* **AT+UNAME=UNAME                               **~/~/Set the username of MQTT
198 -* **AT+PWD=PWD                                        **~/~/Set the password of MQTT
199 -* **AT+PUBTOPIC=NSE01_PUB                    **~/~/Set the sending topic of MQTT
200 -* **AT+SUBTOPIC=NSE01_SUB          ** ~/~/Set the subscription topic of MQTT
217 +* (% style="color:blue" %)**AT+PRO=3   ** (%%) ~/~/ Set to use MQTT protocol to uplink
218 +* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,1883   ** (%%) ~/~/ Set MQTT server address and port
219 +* (% style="color:blue" %)**AT+CLIENT=CLIENT       ** (%%) ~/~/ Set up the CLIENT of MQTT
220 +* (% style="color:blue" %)**AT+UNAME=UNAME                               **(%%)~/~/ Set the username of MQTT
221 +* (% style="color:blue" %)**AT+PWD=PWD                                        **(%%)~/~/ Set the password of MQTT
222 +* (% style="color:blue" %)**AT+PUBTOPIC=NSE01_PUB                    **(%%)~/~/ Set the sending topic of MQTT
223 +* (% style="color:blue" %)**AT+SUBTOPIC=NSE01_SUB          ** (%%) ~/~/ Set the subscription topic of MQTT
201 201  
202 -(% style="text-align:center" %)
203 203  [[image:image-20220907153739-11.png||height="491" width="764"]]
204 204  
205 -(% style="text-align:center" %)
227 +
206 206  [[image:image-20220907153751-12.png||height="555" width="769"]]
207 207  
230 +
208 208  MQTT protocol has a much higher power consumption compare vs UDP / CoAP protocol. Please check the power analyze document and adjust the uplink period to a suitable interval.
209 209  
233 +
210 210  === 2.2.7 Use TCP protocol to uplink data ===
211 211  
236 +
212 212  This feature is supported since firmware version v110
213 213  
214 -* **AT+PRO=4   ** ~/~/ Set to use TCP protocol to uplink
215 -* **AT+SERVADDR=120.24.4.116,5600   ** ~/~/ to set TCP server address and port
239 +* (% style="color:blue" %)**AT+PRO=4   ** (%%) ~/~/ Set to use TCP protocol to uplink
240 +* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5600   ** (%%) ~/~/ to set TCP server address and port
216 216  
217 -(% style="text-align:center" %)
218 218  [[image:image-20220907153818-13.png||height="486" width="668"]]
219 219  
220 -(% style="text-align:center" %)
244 +
221 221  [[image:image-20220907153827-14.png||height="236" width="684"]]
222 222  
247 +
223 223  === 2.2.8 Change Update Interval ===
224 224  
225 -User can use below command to change the **uplink interval**.
226 226  
227 -* **AT+TDC=600      ** ~/~/ Set Update Interval to 600s
251 +Users can use the below command to change the **uplink interval**.
228 228  
229 -**NOTE:**
253 +* (% style="color:blue" %)**AT+TDC=7200      ** (%%) ~/~/ Set Update Interval to 7200s (2 hour)
230 230  
231 -**~1. By default, the device will send an uplink message every 2 hour.**
255 +(% style="color:red" %)**NOTE: By default, the device will send an uplink message every 2 hours. Each Uplink Include 8 set of records in this 2 hour (15 minute interval / record).**
232 232  
257 +
233 233  == 2.3  Uplink Payload ==
234 234  
260 +
235 235  In this mode, uplink payload includes 87 bytes in total by default.
236 236  
237 237  Each time the device uploads a data package, 8 sets of recorded data will be attached. Up to 32 sets of recorded data can be uploaded.
238 238  
239 -|**Size(bytes)**|**8**|**2**|**2**|1|1|1|2|2|4|2|2|4
240 -|**Value**|Device ID|Ver|BAT|Signal Strength|MOD|Interrupt|Soil PH|Soil Temperature|Time stamp|Soil Temperature|Soil PH|Time stamp  .....
265 +(% border="1.5" style="background-color:#ffffcc; color:green; width:520px" %)
266 +|=(% scope="row" style="width: 50px;" %)**Size(bytes)**|(% style="width:40px" %)**8**|(% style="width:20px" %)**2**|(% style="width:25px" %)**2**|(% style="width:60px" %)**1**|(% style="width:20px" %)**1**|(% style="width:40px" %)**1**|(% style="width:40px" %)**2**|(% style="width:50px" %)**2**|(% style="width:50px" %)**4**|(% style="width:50px" %)**2**|(% style="width:35px" %)**2**|(% style="width:40px" %)**4**
267 +|=(% style="width: 96px;" %)**Value**|(% style="width:83px" %)Device ID|(% style="width:44px" %)Ver|(% style="width:42px" %)BAT|(% style="width:124px" %)Signal Strength|(% style="width:57px" %)MOD|(% style="width:80px" %)Interrupt|(% style="width:69px" %)Soil PH|(% style="width:134px" %)Soil Temperature|(% style="width:98px" %)Time stamp|(% style="width:134px" %)Soil Temperature|(% style="width:68px" %)Soil PH|(% style="width:125px" %)Time stamp  .....
241 241  
242 242  If we use the MQTT client to subscribe to this MQTT topic, we can see the following information when the NSPH01 uplink data.
243 243  
244 -(% style="text-align:center" %)
245 245  [[image:image-20220907153902-15.png||height="581" width="804"]]
246 246  
247 247  
274 +(((
248 248  The payload is ASCII string, representative same HEX:
276 +)))
249 249  
250 -0xf86841105675413800640c781701000225010b6315537b010b0226631550fb010e022663154d7701110225631549f1011502246315466b01190223631542e5011d022163153f62011e022163153bde011e022163153859 where:
278 +(((
279 +
280 +)))
251 251  
252 -* Device ID: 0xf868411056754138 = f868411056754138
253 -* Version: 0x0064=100=1.0.0
282 +(((
283 +**0x (% style="color:red" %)__f868411056754138__  (% style="color:blue" %)__0064 __ (% style="color:green" %)__0c78__  (% style="color:#00b0f0" %)__17__  (% style="color:#7030a0" %)__01__  (% style="color:#d60093" %)__00__  (% style="color:#a14d07" %)__0225 __ (% style="color:#0020b0" %) __010b__  (% style="color:#420042" %)__6315537b__  (% style="color:#663300" %)//__010b0226631550fb__  __010e022663154d77  01110225631549f1  011502246315466b  01190223631542e5  011d022163153f62  011e022163153bde 011e022163153859__//(%%)**
284 +)))
254 254  
255 -* BAT: 0x0c78 = 3192 mV = 3.192V
256 -* Singal: 0x17 = 23
257 -* Mod: 0x01 = 1
258 -* Interrupt: 0x00= 0
259 -* Soil PH: 0x0225= 549 = 5.49
260 -* Soil Temperature:0x010B =267=26.7 °C
261 -* Time stamp : 0x6315537b =1662342011
262 -* Soil Temperature,Soil PH,Time stamp : 010b0226631550fb
263 -* 8 sets of recorded data: Temperature,Soil PH,Time stamp : 010e022663154d77,.......
286 +(((
287 +
264 264  
289 +**where:**
290 +)))
291 +
292 +* (% style="color:#037691" %)**Device ID:**(%%)** **0xf868411056754138 = f868411056754138
293 +
294 +* (% style="color:#037691" %)**Version:**  (%%) 0x0064=100=1.0.0
295 +
296 +* (% style="color:#037691" %)**BAT:**   (%%) 0x0c78 = 3192 mV = 3.192V
297 +
298 +* (% style="color:#037691" %)**Singal:** (%%)0x17 = 23
299 +
300 +* (% style="color:#037691" %)**Mod:** (%%) 0x01 = 1
301 +
302 +* (% style="color:#037691" %)**Interrupt:**(%%) 0x00= 0
303 +
304 +* (% style="color:#037691" %)**Soil PH:** (%%) 0x0225= 549 = 5.49
305 +
306 +* (% style="color:#037691" %)**Soil Temperature:**(%%) 0x010b =267=26.7 °C
307 +
308 +* (% style="color:#037691" %)**Time stamp :**   (%%) 0x6315537b =1662342011  ([[Unix Epoch Time>>url:http://www.epochconverter.com/]])
309 +
310 +* (% style="color:#037691" %)**Soil Temperature,Soil PH,Time stamp : **(%%) 010b0226631550fb
311 +
312 +* (% style="color:#037691" %)**8 sets of recorded data:**(%%) Temperature,Soil PH,Time stamp :  010e022663154d77,.......
313 +
265 265  == 2.4  Payload Explanation and Sensor Interface ==
266 266  
267 267  === 2.4.1  Device ID ===
268 268  
318 +
269 269  By default, the Device ID equal to the last 15 bits of IMEI.
270 270  
271 -User can use **AT+DEUI** to set Device ID
321 +User can use (% style="color:blue" %)**AT+DEUI** (%%)to set Device ID
272 272  
323 +
273 273  **Example:**
274 274  
275 275  AT+DEUI=868411056754138
... ... @@ -276,14 +276,18 @@
276 276  
277 277  The Device ID is stored in a none-erase area, Upgrade the firmware or run AT+FDR won't erase Device ID.
278 278  
330 +
279 279  === 2.4.2  Version Info ===
280 280  
333 +
281 281  Specify the software version: 0x64=100, means firmware version 1.00.
282 282  
283 283  For example: 0x00 64 : this device is NSPH01 with firmware version 1.0.0.
284 284  
338 +
285 285  === 2.4.3  Battery Info ===
286 286  
341 +
287 287  Check the battery voltage for NSPH01.
288 288  
289 289  Ex1: 0x0B45 = 2885mV
... ... @@ -290,8 +290,10 @@
290 290  
291 291  Ex2: 0x0B49 = 2889mV
292 292  
348 +
293 293  === 2.4.4  Signal Strength ===
294 294  
351 +
295 295  NB-IoT Network signal Strength.
296 296  
297 297  **Ex1: 0x1d = 29**
... ... @@ -306,18 +306,23 @@
306 306  
307 307  **99**    Not known or not detectable
308 308  
366 +
309 309  === 2.4.5  Soil PH ===
310 310  
369 +
311 311  Get the PH content of the soil. The value range of the register is 300-1000(Decimal), divide this value by 100 to get the percentage of PH in the soil.
312 312  
313 -For example, if the data you get from the register is **__0x05 0xDC__**, the PH content in the soil is
372 +For example, if the data you get from the register is (% style="color:blue" %)**__0x05 0xDC__**(%%), the PH content in the soil is
314 314  
315 -**0229(H) = 549(D) /100 = 5.49.**
374 +(% style="color:blue" %)**0229(H) = 549(D) /100 = 5.49.**
316 316  
376 +
317 317  === 2.4.6  Soil Temperature ===
318 318  
319 -Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is **__0x09 0xEC__**, the temperature content in the soil is
320 320  
380 +Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is (% style="color:blue" %)**__0x09 0xEC__**(%%), the temperature content in the soil is
381 +
382 +
321 321  **Example**:
322 322  
323 323  If payload is 0105H: ((0x0105 & 0x8000)>>15 === 0),temp = 0105(H)/10 = 26.1 °C
... ... @@ -324,35 +324,42 @@
324 324  
325 325  If payload is FF7EH: ((FF7E & 0x8000)>>15 ===1),temp = (FF7E(H)-FFFF(H))/10 = -12.9 °C
326 326  
389 +
327 327  === 2.4.7  Timestamp ===
328 328  
392 +
329 329  Time stamp : 0x6315537b =1662342011
330 330  
331 331  Convert Unix timestamp to time 2022-9-5 9:40:11.
332 332  
397 +
333 333  === 2.4.8  Digital Interrupt ===
334 334  
335 -Digital Interrupt refers to pin **GPIO_EXTI**, and there are different trigger methods. When there is a trigger, the NSPH01 will send a packet to the server.
336 336  
401 +Digital Interrupt refers to pin (% style="color:blue" %)**GPIO_EXTI**(%%), and there are different trigger methods. When there is a trigger, the NSPH01 will send a packet to the server.
402 +
337 337  The command is:
338 338  
339 -**AT+INTMOD=3 ** ~/~/(more info about INMOD please refer [[**AT Command Manual**>>url:https://www.dragino.com/downloads/downloads/NB-IoT/NBSN95/DRAGINO_NBSN95-NB_AT%20Commands_v1.1.0.pdf]])**.**
405 +(% style="color:blue" %)**AT+INTMOD=3 ** (%%) ~/~/(more info about INMOD please refer [[**AT Command Manual**>>url:https://www.dragino.com/downloads/downloads/NB-IoT/NBSN95/DRAGINO_NBSN95-NB_AT%20Commands_v1.1.0.pdf]])**.**
340 340  
341 341  The lower four bits of this data field shows if this packet is generated by interrupt or not. Click here for the hardware and software set up.
342 342  
343 -Example:
344 344  
410 +**Example:**
411 +
345 345  0x(00): Normal uplink packet.
346 346  
347 347  0x(01): Interrupt Uplink Packet.
348 348  
416 +
349 349  === 2.4.9  ​+5V Output ===
350 350  
419 +
351 351  NSPH01 will enable +5V output before all sampling and disable the +5v after all sampling. 
352 352  
353 353  The 5V output time can be controlled by AT Command.
354 354  
355 -**AT+5VT=1000**
424 +(% style="color:blue" %)**AT+5VT=1000**
356 356  
357 357  Means set 5V valid time to have 1000ms. So the real 5V output will actually have 1000ms + sampling time for other sensors.** **
358 358  
... ... @@ -359,21 +359,16 @@
359 359  
360 360  == 2.5  Downlink Payload ==
361 361  
431 +
362 362  By default, NSPH01 prints the downlink payload to console port.
363 363  
364 -(% style="text-align:center" %)
365 365  [[image:image-20220907154636-17.png]]
366 366  
367 367  
437 +(% style="color:blue" %)**Examples:**
368 368  
439 +* (% style="color:#037691" %)** Set TDC**
369 369  
370 -
371 -
372 -
373 -**Examples:**
374 -
375 -* **Set TDC**
376 -
377 377  If the payload=0100003C, it means set the END Node's TDC to 0x00003C=60(S), while type code is 01.
378 378  
379 379  Payload:    01 00 00 1E    TDC=30S
... ... @@ -380,16 +380,18 @@
380 380  
381 381  Payload:    01 00 00 3C    TDC=60S
382 382  
383 -* **Reset**
447 +* (% style="color:#037691" %)** Reset**
384 384  
385 385  If payload = 0x04FF, it will reset the NSPH01
386 386  
387 -* **INTMOD**
451 +* (% style="color:#037691" %)** INTMOD**
388 388  
389 389  Downlink Payload: 06000003, Set AT+INTMOD=3
390 390  
455 +
391 391  == 2.6  ​LED Indicator ==
392 392  
458 +
393 393  The NSPH01 has an internal LED which is to show the status of different state.
394 394  
395 395  * When power on, NSPH01 will detect if sensor probe is connected, if probe detected, LED will blink four times. (no blinks in this step is no probe)
... ... @@ -397,16 +397,20 @@
397 397  * After NSPH01 join NB-IoT network. The LED will be ON for 3 seconds.
398 398  * For each uplink probe, LED will be on for 500ms.
399 399  
400 -== 2.7 Installation and Maintain ==
466 +== 2.7  Installation and Maintain ==
401 401  
402 -=== 2.7.1 Before measurement ===
468 +=== 2.7.1  Before measurement ===
403 403  
470 +
404 404  If the NSPH01 has more than 7 days not use or just clean the pH probe. User should put the probe inside pure water for more than 24 hours for activation. If no put in water, user need to put inside soil for more than 24 hours to ensure the measurement accuracy. 
405 405  
406 -=== 2.7.2 Measurement ===
407 407  
408 -**Measurement the soil surface:**
474 +=== 2.7.2  Measurement ===
409 409  
476 +
477 +(% style="color:#037691" %)**Measurement the soil surface:**
478 +
479 +
410 410  [[image:image-20220907154700-18.png]] ​
411 411  
412 412  Choose the proper measuring position. Split the surface soil according to the measured deep.
... ... @@ -417,14 +417,17 @@
417 417  
418 418  Put soil over the probe after insert. And start to measure.
419 419  
420 -**Measurement inside soil:**
421 421  
491 +(% style="color:#037691" %)**Measurement inside soil:**
492 +
422 422  Dig a hole with diameter > 20CM.
423 423  
424 424  Insert the probe inside, method like measure the surface.
425 425  
426 -=== 2.7.3 Maintain Probe ===
427 427  
498 +=== 2.7.3  Maintain Probe ===
499 +
500 +
428 428  1. pH probe electrode is fragile and no strong. User must avoid strong force or hitting it.
429 429  1. After long time use (3~~ 6  months). The probe electrode needs to be clean; user can use high grade sandpaper to polish it or put in 5% hydrochloric acid for several minutes. After the metal probe looks like new, user can use pure water to wash it.
430 430  1. Probe reference electrode is also no strong, need to avoid strong force or hitting.
... ... @@ -432,12 +432,13 @@
432 432  1. Avoid the probes to touch oily matter. Which will cause issue in accuracy.
433 433  1. The probe is IP68 can be put in water.
434 434  
435 -== 2.8 PH and Temperature alarm function ==
508 +== 2.8  PH and Temperature alarm function ==
436 436  
437 -➢ AT Command:
438 438  
439 -AT+ PHALARM=min,max
511 +(% style="color:#037691" %)**➢ AT Command:**
440 440  
513 +(% style="color:blue" %)**AT+ PHALARM=min,max**
514 +
441 441  ² When min=3, and max≠0, Alarm higher than max
442 442  
443 443  ² When min≠0, and max=0, Alarm lower than min
... ... @@ -444,10 +444,11 @@
444 444  
445 445  ² When min≠0 and max≠0, Alarm higher than max or lower than min
446 446  
447 -Example:
448 448  
449 -AT+ PHALARM =5,8 ~/~/ Alarm when PH lower than 5.
522 +(% style="color:blue" %)**Example:**
450 450  
524 +AT+ PHALARM =5,8  ~/~/ Alarm when PH lower than 5.
525 +
451 451  AT+ TEMPALARM=min,max
452 452  
453 453  ² When min=0, and max≠0, Alarm higher than max
... ... @@ -456,98 +456,71 @@
456 456  
457 457  ² When min≠0 and max≠0, Alarm higher than max or lower than min
458 458  
459 -Example:
460 460  
461 -AT+ TEMPALARM=20,30 ~/~/ Alarm when temperature lower than 20.
535 +(% style="color:blue" %)**Example:**
462 462  
537 +AT+ TEMPALARM=20,30  ~/~/ Alarm when temperature lower than 20.
463 463  
464 -== 2.9 Set the number of data to be uploaded and the recording time ==
465 465  
466 -➢ AT Command:
540 +== 2.9  Set the number of data to be uploaded and the recording time ==
467 467  
468 -AT+TR=900  ~/~/The unit is seconds, and the default is to record data once every 900 seconds.( The minimum can be set to 180 seconds)
469 469  
543 +(% style="color:#037691" %)**➢ AT Command:**
470 470  
471 -AT+NOUD=8  ~/~/The device uploads 8 sets of recorded data by default. Up to 32 sets of record data can be uploaded.
545 +* (% style="color:blue" %)**AT+TR=900**     (%%) ~/~/  The unit is seconds, and the default is to record data once every 900 seconds.( The minimum can be set to 180 seconds)
546 +* (% style="color:blue" %)**AT+NOUD=8**     (%%) ~/~/  The device uploads 8 sets of recorded data by default. Up to 32 sets of record data can be uploaded.
472 472  
473 -== 2.10 Read or Clear cached data ==
548 + The diagram below explains the relationship between TR, NOUD, and TDC more clearly**:**
474 474  
475 -➢ AT Command:
550 +[[image:image-20221009000933-1.png||height="750" width="1043"]]
476 476  
477 -AT+CDP ~/~/ Read cached data
478 478  
479 -[[image:image-20220907154700-19.png]]
553 +== 2.10  Read or Clear cached data ==
480 480  
481 481  
482 -AT+CDP=0 ~/~/ Clear cached data
556 +(% style="color:#037691" %)**➢ AT Command:**
483 483  
558 +* (% style="color:blue" %)**AT+CDP**        (%%) ~/~/  Read cached data
559 +* (% style="color:blue" %)**AT+CDP=0**    (%%) ~/~/  Clear cached data
484 484  
485 -== 2.11 Calibration ==
561 +[[image:image-20220907154700-19.png]]
486 486  
487 -User can do calibration for the probe. It is limited to use below pH buffer solution to calibrate: 4.00, 6.86, 9.18. When calibration, user need to clean the electrode and put the probe in the pH buffer solution to wait the value stable ( a new clean electrode might need max 24 hours to be stable).
488 488  
489 -After stable, user can use below command to calibrate.
564 +== 2.11  Calibration ==
490 490  
491 -[[image:image-20220907154700-20.png]] ​
492 492  
493 -== 2.12  ​Firmware Change Log ==
567 +User can do calibration for the probe. It is limited to use below pH buffer solution to calibrate: 4.00, 6.86, 9.18. When calibration, user need to clean the electrode and put the probe in the pH buffer solution to wait the value stable ( a new clean electrode might need max 24 hours to be stable).
494 494  
495 -Download URL & Firmware Change log: [[https:~~/~~/www.dropbox.com/sh/1zmcakvbkf24f8x/AACmq2dZ3iRB9F1nVWeEB9Moa?dl=0>>url:https://www.dropbox.com/sh/1zmcakvbkf24f8x/AACmq2dZ3iRB9F1nVWeEB9Moa?dl=0]]
569 +After stable, user can use below command to calibrate.
496 496  
497 -Upgrade Instruction: [[Upgrade Firmware>>path:#H5.1200BHowtoUpgradeFirmware]]
498 498  
499 -== 2.13  ​Battery Analysis ==
572 +[[image:image-20220907154700-20.png]] ​
500 500  
501 -=== 2.13.1  ​Battery Type ===
502 502  
503 -The NSPH01 battery is a combination of an 8500mAh Li/SOCI2 Battery and a Super Capacitor. The battery is none-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
575 +== 2.12  ​Firmware Change Log ==
504 504  
505 -The battery is designed to last for several years depends on the actually use environment and update interval. 
506 506  
507 -The battery related documents as below:
578 +Download URL & Firmware Change log: [[https:~~/~~/www.dropbox.com/sh/1tv07fro2pvjqj8/AAD-2wbfGfluTZfh38fQqdA_a?dl=0>>https://www.dropbox.com/sh/1tv07fro2pvjqj8/AAD-2wbfGfluTZfh38fQqdA_a?dl=0]]
508 508  
509 -* [[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
510 -* [[Lithium-Thionyl Chloride Battery datasheet>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
511 -* [[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
580 +Upgrade Instruction: [[Upgrade Firmware>>||anchor="H5.1200BHowtoUpgradeFirmware"]]
512 512  
513 -[[image:image-20220907154700-21.png]] ​
514 514  
515 -=== 2.13.2  Power consumption Analyze ===
583 +== 2.13 Battery & Power Consumption ==
516 516  
517 -Dragino battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
518 518  
519 -Instruction to use as below:
586 +NSPH01 uses ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
520 520  
521 -**Step 1:  **Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/]]
588 +[[**Battery Info & Power Consumption Analyze**>>url:http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
522 522  
523 -**Step 2: ** Open it and choose
524 524  
525 -* Product Model
526 -* Uplink Interval
527 -* Working Mode
528 -
529 -And the Life expectation in difference case will be shown on the right.
530 -
531 -(% style="text-align:center" %)
532 -[[image:image-20220907154700-22.jpeg]]
533 -
534 -​
535 -
536 -=== 2.13.3  ​Battery Note ===
537 -
538 -The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
539 -
540 -=== 2.13.4  Replace the battery ===
541 -
542 -The default battery pack of NSPH01 includes a ER26500 plus super capacitor. If user can't find this pack locally, they can find ER26500 or equivalence without the SPC1520 capacitor, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes).
543 -
544 544  = 3. ​ Access NB-IoT Module =
545 545  
593 +
546 546  Users can directly access the AT command set of the NB-IoT module.
547 547  
548 548  The AT Command set can refer the BC35-G NB-IoT Module AT Command: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/]] 
549 549  
550 -(% style="text-align:center" %)
598 +
551 551  [[image:image-20220907154700-23.png]]
552 552  
553 553  ​
... ... @@ -556,6 +556,7 @@
556 556  
557 557  == 4.1  Access AT Commands ==
558 558  
607 +
559 559  See this link for detail:  [[https:~~/~~/www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0>>url:https://www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0]]
560 560  
561 561  AT+<CMD>?  : Help on <CMD>
... ... @@ -566,8 +566,9 @@
566 566  
567 567  AT+<CMD>=?  : Get the value
568 568  
569 -**General Commands**      
570 570  
619 +(% style="color:#037691" %)**General Commands**      
620 +
571 571  AT  : Attention       
572 572  
573 573  AT?  : Short Help     
... ... @@ -592,13 +592,18 @@
592 592  
593 593  AT+TR      : Get or Set record time"
594 594  
645 +AT+APN     : Get or set the APN
595 595  
596 -AT+NOUD      : Get or Set the number of data to be uploaded
647 +AT+FBAND   : Get or Set whether to automatically modify the frequency band
597 597  
649 +AT+DNSCFG  : Get or Set DNS Server
598 598  
599 -AT+CDP     : Read or Clear cached data
651 +AT+GETSENSORVALUE   : Returns the current sensor measurement
600 600  
653 +AT+NOUD      : Get or Set the number of data to be uploaded
601 601  
655 +AT+CDP     : Read or Clear cached data
656 +
602 602  AT+TEMPALARM      : Get or Set alarm of temp
603 603  
604 604  AT+PHALARM     : Get or Set alarm of PH
... ... @@ -606,16 +606,18 @@
606 606  AT+ PHCAL  : calibrate PH value
607 607  
608 608  
609 -**COAP Management**      
664 +(% style="color:#037691" %)**COAP Management**      
610 610  
611 611  AT+URI            : Resource parameters
612 612  
613 -**UDP Management**
614 614  
669 +(% style="color:#037691" %)**UDP Management**
670 +
615 615  AT+CFM          : Upload confirmation mode (only valid for UDP)
616 616  
617 -**MQTT Management**
618 618  
674 +(% style="color:#037691" %)**MQTT Management**
675 +
619 619  AT+CLIENT               : Get or Set MQTT client
620 620  
621 621  AT+UNAME  : Get or Set MQTT Username
... ... @@ -626,54 +626,71 @@
626 626  
627 627  AT+SUBTOPIC  : Get or Set MQTT subscription topic
628 628  
629 -**Information**          
630 630  
687 +(% style="color:#037691" %)**Information**          
688 +
631 631  AT+FDR  : Factory Data Reset
632 632  
633 633  AT+PWORD  : Serial Access Password
634 634  
693 +
635 635  = ​5.  FAQ =
636 636  
637 637  == 5.1 ​ How to Upgrade Firmware ==
638 638  
698 +
639 639  User can upgrade the firmware for 1) bug fix, 2) new feature release.
640 640  
641 641  Please see this link for how to upgrade:  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList]]
642 642  
643 -**Notice, **NSPH01 **and **NSPH01 **share the same mother board. They use the same connection and method to update.**
703 +(% style="color:red" %)**Notice, NSPH01 and LSPH01 share the same mother board. They use the same connection and method to update.**
644 644  
705 +
645 645  == 5.2  Can I calibrate NSPH01 to different soil types? ==
646 646  
708 +
647 647  NSPH01 is calibrated for saline-alkali soil and loamy soil. If users want to use it for other soil, they can calibrate the value in the IoT platform base on the value measured by saline-alkali soil and loamy soil. The formula can be found at [[this link>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/LSE01/Calibrate_to_other_Soil_20220605.pdf]].
648 648  
711 +
649 649  = 6.  Trouble Shooting =
650 650  
651 651  == 6.1  ​Connection problem when uploading firmware ==
652 652  
716 +
653 653  **Please see: **[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting]]
654 654  
719 +
655 655  == 6.2  AT Command input doesn't work ==
656 656  
657 -In the case if user can see the console output but can't type input to the device. Please check if you already include the **ENTER** while sending out the command. Some serial tool doesn't send **ENTER** while press the send key, user need to add ENTER in their string.
658 658  
723 +In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER** (%%)while press the send key, user need to add ENTER in their string.
724 +
725 +
659 659  = 7. ​ Order Info =
660 660  
728 +
661 661  Part Number**:** NSPH01
662 662  
731 +
732 +
663 663  = 8.  Packing Info =
664 664  
735 +
665 665  **Package Includes**:
666 666  
667 -* NSPH01 NB-IoT Soil Moisture & EC Sensor x 1
738 +* NSPH01 NB-IoT pH Sensor x 1
668 668  * External antenna x 1
669 669  
670 670  **Dimension and weight**:
671 671  
672 -* Size: 195 x 125 x 55 mm
673 -* Weight:   420g
743 +* Device Size: cm
744 +* Device Weight: g
745 +* Package Size / pcs : cm
746 +* Weight / pcs : g
674 674  
675 675  = 9.  Support =
676 676  
750 +
677 677  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
678 678  * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]
679 679  
image-20220912144017-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +149.6 KB
Content
image-20220923101327-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +12.1 KB
Content
image-20221009000933-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Edwin
Size
... ... @@ -1,0 +1,1 @@
1 +282.9 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0