Last modified by Bei Jinggeng on 2024/03/30 17:53
<
From version < 41.1 >
edited by David Huang
on 2022/09/07 17:00
To version < 56.6 >
edited by Xiaoling
on 2022/10/25 16:43
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.David
1 +XWiki.Xiaoling
Content
... ... @@ -1,31 +1,45 @@
1 1  (% style="text-align:center" %)
2 -[[image:)YK]Y_LZJIO]J2~~VA}OQJM2.png]]
2 +[[image:)YK]Y_LZJIO]J2~~VA}OQJM2.png||height="442" width="410"]]
3 3  
4 -= **1. Introduction** =
4 +**Table of Contents:**
5 5  
6 -== **1.1 ​What is NSPH01 Soil pH Sensor** ==
6 +{{toc/}}
7 7  
8 -The Dragino NSPH01 is a **NB-IOT soil ph sensor** for IoT of Agriculture. It is designed to measure the soil PH and soil temperature, so to send to the platform to analyze the soil acid or alkali level. The probe is IP68 waterproof.
9 9  
10 -NSPH01 probe is made by Solid AgCl reference electrode and Pure metal pH sensitive electrode. It can detect soil's** pH **with high accuracy and stable value. The NSPH01 probe can be buried into soil for long time use.
11 11  
10 += 1.  Introduction =
11 +
12 +
13 +== 1.1 ​ What is NSPH01 Soil pH Sensor ==
14 +
15 +
16 +The Dragino NSPH01 is a (% style="color:blue" %)**NB-IoT soil pH sensor**(%%) for IoT of Agriculture. It is designed to measure the soil pH and soil temperature, so to send to the platform to analyze the soil acid or alkali level. The probe is IP68 waterproof.
17 +
18 +NSPH01 probe is made by Solid AgCl reference electrode and Pure metal pH sensitive electrode. It can detect soil's** (% style="color:blue" %)pH (%%)**with high accuracy and stable value. The NSPH01 probe can be buried into soil for long time use.
19 +
12 12  NarrowBand-Internet of Things (NB-IoT) is a standards-based low power wide area (LPWA) technology developed to enable a wide range of new IoT devices and services. NB-IoT significantly improves the power consumption of user devices, system capacity and spectrum efficiency, especially in deep coverage.
13 -\\NSPH01 supports different uplink methods include **TCP,MQTT,UDP and CoAP  **for different application requirement.
14 -\\NSPH01 is powered by  **8500mAh Li-SOCI2 battery**, It is designed for long term use up to 5 years. (Actually Battery life depends on the use environment, update period & uplink method)
15 -\\To use NSPH01, user needs to check if there is NB-IoT coverage in local area and with the bands NSPH01 supports. If the local operate support it, user needs to get a **NB-IoT SIM card** from local operator and install NSPH01 to get NB-IoT network connection.
16 16  
17 -(% style="text-align:center" %)
22 +NSPH01 supports different uplink methods include (% style="color:blue" %)**TCP,MQTT,UDP and CoAP  **(%%)for different application requirement.
23 +
24 +NSPH01 is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), It is designed for long term use up to 5 years. (Actually Battery life depends on the use environment, update period & uplink method)
25 +
26 +To use NSPH01, user needs to check if there is NB-IoT coverage in the installation area and with the bands NSPH01 supports. If the local operator supports it, user needs to get a (% style="color:blue" %)**NB-IoT SIM card** (%%)from local operator and install NSPH01 to get NB-IoT network connection.
27 +
28 +
18 18  [[image:image-20220907153151-1.png]]
19 19  
20 -(% style="text-align:center" %)
31 +
21 21  [[image:M_K`YF9`CAYAE\@}3T]FHT$9.png]]
22 22  
23 -**1.2 Features**
24 24  
35 +
36 +== 1.2  Features ==
37 +
38 +
25 25  * NB-IoT Bands: B1/B3/B8/B5/B20/B28 @H-FDD
26 26  * Monitor soil pH with temperature compensation.
27 27  * Monitor soil temperature
28 -* PH and Temperature alarm function
42 +* pH and Temperature alarm function
29 29  * Monitor Battery Level
30 30  * Support pH calibration by end user
31 31  * Uplink on periodically
... ... @@ -34,17 +34,19 @@
34 34  * IP68 rate for the Sensor Probe
35 35  * Ultra-Low Power consumption
36 36  * AT Commands to change parameters
37 -* Micro SIM card slot for NB-IoT SIM
51 +* Micro SIM card slot
38 38  * 8500mAh Battery for long term use
39 39  
40 -**1.3  Specification**
41 41  
42 -**Common DC Characteristics:**
55 +== 1.3  Specification ==
43 43  
57 +
58 +(% style="color:#037691" %)**Common DC Characteristics:**
59 +
44 44  * Supply Voltage: 2.1v ~~ 3.6v
45 45  * Operating Temperature: -40 ~~ 85°C
46 46  
47 -**NB-IoT Spec:**
63 +(% style="color:#037691" %)**NB-IoT Spec:**
48 48  
49 49  * - B1 @H-FDD: 2100MHz
50 50  * - B3 @H-FDD: 1800MHz
... ... @@ -53,10 +53,12 @@
53 53  * - B20 @H-FDD: 800MHz
54 54  * - B28 @H-FDD: 700MHz
55 55  
56 -**1.4 Probe Specification**
57 57  
58 -**Soil pH:**
73 +== 1.4  Probe Specification ==
59 59  
75 +
76 +(% style="color:#037691" %)**Soil pH:**
77 +
60 60  * Range: 3 ~~ 10 pH
61 61  * Resolution: 0.01 pH
62 62  * Accuracy: ±2% under (0~~50 ℃, Accuracy will poor under 0 due to frozen)
... ... @@ -64,7 +64,7 @@
64 64  * IP68 Protection
65 65  * Length: 3.5 meters
66 66  
67 -**Soil Temperature:**
85 +(% style="color:#037691" %)**Soil Temperature:**
68 68  
69 69  * Range -40℃～85℃
70 70  * Resolution: 0.1℃
... ... @@ -72,199 +72,256 @@
72 72  * IP68 Protection
73 73  * Length: 3.5 meters
74 74  
75 -**1.5 ​Applications**
76 76  
94 +== 1.5  ​Applications ==
95 +
96 +
77 77  * Smart Agriculture
78 78  
79 -**1.6 Pin mapping and power on**
80 80  
81 -(% style="text-align:center" %)
100 +== 1.6  Pin mapping and power on ==
101 +
102 +
82 82  [[image:image-20220907153300-2.png]]
83 83  
84 84  
85 -**2.  Use NSPH01 to communicate with IoT Server**
86 86  
87 -**2.1  How it works**
107 += 2.  Use NSPH01 to communicate with IoT Server =
88 88  
109 +
110 +== 2.1  How it works ==
111 +
112 +
89 89  The NSPH01 is equipped with a NB-IoT module, the pre-loaded firmware in NSPH01 will get environment data from sensors and send the value to local NB-IoT network via the NB-IoT module.  The NB-IoT network will forward this value to IoT server via the protocol defined by NSPH01.
90 90  
91 91  The diagram below shows the working flow in default firmware of NSPH01:
92 92  
93 -(% style="text-align:center" %)
117 +
94 94  [[image:image-20220907153416-3.png]]
95 95  
96 -**2.2 ​ Configure the NSPH01**
97 97  
98 -**2.2.1 Test Requirement**
99 99  
100 -To use NSPH01 in your city, make sure meet below requirements:
122 +== 2.2 ​ Configure the NSPH01 ==
101 101  
124 +
125 +=== 2.2.1 Test Requirement ===
126 +
127 +
128 +To use NSPH01 in the field, make sure meet below requirements:
129 +
102 102  * Your local operator has already distributed a NB-IoT Network there.
103 103  * The local NB-IoT network used the band that NSPH01 supports.
104 104  * Your operator is able to distribute the data received in their NB-IoT network to your IoT server.
105 105  
106 -Below figure shows our testing structure. Here we have NB-IoT network coverage by China Mobile, the band they use is B8.  The NSPH01 will use CoAP(120.24.4.116:5683) or raw UDP(120.24.4.116:5601) or MQTT(120.24.4.116:1883)or TCP(120.24.4.116:5600)protocol to send data to the test server
134 +Below figure shows our testing structure. Here we have NB-IoT network coverage by China Mobile, the band they use is B8.  The NSPH01 will use** CoAP(120.24.4.116:5683) **or raw **UDP(120.24.4.116:5601)** or **MQTT(120.24.4.116:1883)**or **TCP(120.24.4.116:5600)**protocol to send data to the test server.
107 107  
108 -(% style="text-align:center" %)
136 +
109 109  [[image:image-20220907153445-4.png]]
110 110  
111 111  
112 -**2.2.2 Insert SIM card**
113 113  
114 -Insert the NB-IoT Card get from your provider.
141 +=== 2.2.2 Insert SIM card ===
115 115  
116 -User need to take out the NB-IoT module and insert the SIM card like below:
117 117  
118 -(% style="text-align:center" %)
144 +User need to take out the NB-IoT module and insert the SIM card like below. ((% style="color:red" %) Pay attention to the direction(%%))
145 +
146 +
119 119  [[image:image-20220907153505-5.png]]
120 120  
121 -**2.2.3 Connect USB – TTL to NSPH01 to configure it**
122 122  
123 -User need to configure NSPH01 via serial port to set the **Server Address** / **Uplink Topic** to define where and how-to uplink packets. NSPH01 support AT Commands, user can use a USB to TTL adapter to connect to NSPH01 and use AT Commands to configure it, as below.
124 124  
125 -**Connection:**
151 +=== 2.2.3 Connect USB – TTL to NSPH01 to configure it ===
126 126  
127 - USB TTL GND <~-~-~-~-> GND
128 128  
129 - USB TTL TXD <~-~-~-~-> UART_RXD
154 +User need to configure NSPH01 via serial port to set the (% style="color:blue" %)**Server Address** / **Uplink Topic**(%%) to define where and how-to uplink packets. NSPH01 support AT Commands, user can use a USB to TTL adapter to connect to NSPH01 and use AT Commands to configure it, as below.
130 130  
131 - USB TTL RXD <~-~-~-~-> UART_TXD
132 132  
157 +(% style="color:blue" %)**Connection:**
158 +
159 +**~ (% style="background-color:yellow" %) USB TTL GND <~-~-~-~->  GND(%%)**
160 +
161 +**~ (% style="background-color:yellow" %) USB TTL TXD  <~-~-~-~->  UART_RXD(%%)**
162 +
163 +**~ (% style="background-color:yellow" %) USB TTL RXD  <~-~-~-~->  UART_TXD(%%)**
164 +
165 +
133 133  In the PC, use below serial tool settings:
134 134  
135 -* Baud:  **9600**
136 -* Data bits:** 8**
137 -* Stop bits: **1**
138 -* Parity:  **None**
139 -* Flow Control: **None**
168 +* Baud:  (% style="color:green" %)**9600**
169 +* Data bits:**  (% style="color:green" %)8(%%)**
170 +* Stop bits:  (% style="color:green" %)**1**
171 +* Parity:  (% style="color:green" %)**None**
172 +* Flow Control: (% style="color:green" %)**None**
140 140  
141 -Make sure the switch is in FLASH position, then power on device by connecting the jumper on NSPH01. NSPH01 will output system info once power on as below, we can enter the **password: 12345678** to access AT Command input.
174 +Make sure the switch is in FLASH position, then power on device by connecting the jumper on NSPH01. NSPH01 will output system info once power on as below, we can enter the (% style="color:green" %)**password: 12345678**(%%) to access AT Command input.
142 142  
143 -(% style="text-align:center" %)
144 -[[image:image-20220907153529-6.png]]
145 145  
146 -**Note: the valid AT Commands can be found at:  **[[**https:~~/~~/www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0**>>url:https://www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0]]
177 +[[image:image-20220912144017-1.png]]
147 147  
148 -**2.2.4 Use CoAP protocol to uplink data**
149 149  
150 -**Note: if you don't have CoAP server, you can refer this link to set up one: **[[**http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/**>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/]]
180 +(% style="color:red" %)**Note: the valid AT Commands can be found at:**(%%)**  **[[**https:~~/~~/www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0**>>url:https://www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0]]
151 151  
152 -**Use below commands:**
153 153  
154 -* **AT+PRO=1**   ~/~/ Set to use CoAP protocol to uplink
155 -* **AT+SERVADDR=120.24.4.116,5683   ** ~/~/ to set CoAP server address and port
156 -* **AT+URI=5,11,"mqtt",11,"coap",12,"0",15,"c=text1",23,"0" ** ~/~/Set COAP resource path
157 157  
184 +=== 2.2.4 Use CoAP protocol to uplink data ===
185 +
186 +
187 +(% style="color:red" %)**Note: if you don't have CoAP server, you can refer this link to set up one:**(%%)** **[[**http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/**>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/]]
188 +
189 +
190 +(% style="color:blue" %)**Use below commands:**
191 +
192 +* (% style="color:#037691" %)**AT+PRO=1**                         (%%) ~/~/  Set to use CoAP protocol to uplink
193 +* (% style="color:#037691" %)**AT+SERVADDR=120.24.4.116,5683   ** (%%) ~/~/  to set CoAP server address and port
194 +* (% style="color:#037691" %)**AT+URI=5,11,"mqtt",11,"coap",12,"0",15,"c=text1",23,"0" ** (%%) ~/~/  Set COAP resource path
195 +
158 158  For parameter description, please refer to AT command set
159 159  
160 -(% style="text-align:center" %)
198 +
161 161  [[image:image-20220907153551-7.png||height="502" width="740"]]
162 162  
163 -After configure the server address and **reset the device** (via AT+ATZ ), NSPH01 will start to uplink sensor values to CoAP server.
164 164  
165 -(% style="text-align:center" %)
202 +After configure the server address and (% style="color:green" %)**reset the device (via AT+ATZ )**(%%), NSPH01 will start to uplink sensor values to CoAP server.
203 +
204 +
166 166  [[image:image-20220907153612-8.png||height="529" width="729"]]
167 167  
168 168  
169 -**2.2.5 Use UDP protocol to uplink data(Default protocol)**
170 170  
209 +=== 2.2.5 Use UDP protocol to uplink data(Default protocol) ===
210 +
211 +
171 171  This feature is supported since firmware version v1.0.1
172 172  
173 -* **AT+PRO=2   ** ~/~/ Set to use UDP protocol to uplink
174 -* **AT+SERVADDR=120.24.4.116,5601   ** ~/~/ to set UDP server address and port
175 -* **AT+CFM=1       ** ~/~/If the server does not respond, this command is unnecessar
214 +* (% style="color:blue" %)**AT+PRO=2   ** (%%) ~/~/  Set to use UDP protocol to uplink
215 +* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5601   ** (%%) ~/~/  to set UDP server address and port
216 +* (% style="color:blue" %)**AT+CFM=1       ** (%%) ~/~/  If the server does not respond, this command is unnecessar
176 176  
177 -(% style="text-align:center" %)
178 178  [[image:image-20220907153643-9.png||height="401" width="734"]]
179 179  
180 -(% style="text-align:center" %)
220 +
181 181  [[image:image-20220907153703-10.png||height="309" width="738"]]
182 182  
183 183  
184 -**2.2.6 Use MQTT protocol to uplink data**
185 185  
225 +=== 2.2.6 Use MQTT protocol to uplink data ===
226 +
227 +
186 186  This feature is supported since firmware version v110
187 187  
188 -* **AT+PRO=3   ** ~/~/Set to use MQTT protocol to uplink
189 -* **AT+SERVADDR=120.24.4.116,1883   ** ~/~/Set MQTT server address and port
190 -* **AT+CLIENT=CLIENT       ** ~/~/Set up the CLIENT of MQTT
191 -* **AT+UNAME=UNAME                               **~/~/Set the username of MQTT
192 -* **AT+PWD=PWD                                        **~/~/Set the password of MQTT
193 -* **AT+PUBTOPIC=NSE01_PUB                    **~/~/Set the sending topic of MQTT
194 -* **AT+SUBTOPIC=NSE01_SUB          ** ~/~/Set the subscription topic of MQTT
230 +* (% style="color:blue" %)**AT+PRO=3   ** (%%) ~/~/ Set to use MQTT protocol to uplink
231 +* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,1883   ** (%%) ~/~/ Set MQTT server address and port
232 +* (% style="color:blue" %)**AT+CLIENT=CLIENT       ** (%%) ~/~/ Set up the CLIENT of MQTT
233 +* (% style="color:blue" %)**AT+UNAME=UNAME                               **(%%)~/~/ Set the username of MQTT
234 +* (% style="color:blue" %)**AT+PWD=PWD                                        **(%%)~/~/ Set the password of MQTT
235 +* (% style="color:blue" %)**AT+PUBTOPIC=NSE01_PUB                    **(%%)~/~/ Set the sending topic of MQTT
236 +* (% style="color:blue" %)**AT+SUBTOPIC=NSE01_SUB          ** (%%) ~/~/ Set the subscription topic of MQTT
195 195  
196 -(% style="text-align:center" %)
197 197  [[image:image-20220907153739-11.png||height="491" width="764"]]
198 198  
199 -(% style="text-align:center" %)
240 +
200 200  [[image:image-20220907153751-12.png||height="555" width="769"]]
201 201  
243 +
202 202  MQTT protocol has a much higher power consumption compare vs UDP / CoAP protocol. Please check the power analyze document and adjust the uplink period to a suitable interval.
203 203  
204 -**2.2.7 Use TCP protocol to uplink data**
205 205  
247 +
248 +
249 +=== 2.2.7 Use TCP protocol to uplink data ===
250 +
251 +
206 206  This feature is supported since firmware version v110
207 207  
208 -* **AT+PRO=4   ** ~/~/ Set to use TCP protocol to uplink
209 -* **AT+SERVADDR=120.24.4.116,5600   ** ~/~/ to set TCP server address and port
254 +* (% style="color:blue" %)**AT+PRO=4   ** (%%) ~/~/ Set to use TCP protocol to uplink
255 +* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5600   ** (%%) ~/~/ to set TCP server address and port
210 210  
211 -(% style="text-align:center" %)
212 212  [[image:image-20220907153818-13.png||height="486" width="668"]]
213 213  
214 -(% style="text-align:center" %)
259 +
215 215  [[image:image-20220907153827-14.png||height="236" width="684"]]
216 216  
217 -**2.2.8 Change Update Interval**
218 218  
219 -User can use below command to change the **uplink interval**.
220 220  
221 -* **AT+TDC=600      ** ~/~/ Set Update Interval to 600s
264 +=== 2.2.8 Change Update Interval ===
222 222  
223 -**NOTE:**
224 224  
225 -**~1. By default, the device will send an uplink message every 2 hour.**
267 +Users can use the below command to change the **uplink interval**.
226 226  
227 -**2.3  Uplink Payload**
269 +* (% style="color:blue" %)**AT+TDC=7200      ** (%%) ~/~/ Set Update Interval to 7200s (2 hour)
228 228  
271 +(% style="color:red" %)**NOTE: By default, the device will send an uplink message every 2 hours. Each Uplink Include 8 set of records in this 2 hour (15 minute interval / record).**
272 +
273 +
274 +
275 +== 2.3  Uplink Payload ==
276 +
277 +
229 229  In this mode, uplink payload includes 87 bytes in total by default.
230 230  
231 231  Each time the device uploads a data package, 8 sets of recorded data will be attached. Up to 32 sets of recorded data can be uploaded.
232 232  
233 -(% style="width:934px" %)
234 -|(% style="width:93px" %)**Size(bytes)**|(% style="width:82px" %)**8**|(% style="width:43px" %)**2**|(% style="width:41px" %)**2**|(% style="width:126px" %)**1**|(% style="width:54px" %)**1**|(% style="width:84px" %)1|(% style="width:75px" %)2|(% style="width:133px" %)2|(% style="width:70px" %)2|(% style="width:127px" %)4   
235 -|(% style="width:93px" %)**Value**|(% style="width:82px" %)Device ID|(% style="width:43px" %)Ver|(% style="width:41px" %)BAT|(% style="width:126px" %)Signal Strength|(% style="width:54px" %)MOD|(% style="width:84px" %)Interrupt|(% style="width:75px" %)Soil PH|(% style="width:133px" %)Soil Temperature|(% style="width:70px" %)Soil PH|(% style="width:127px" %)Time stamp  .....
282 +(% border="1.5" style="background-color:#ffffcc; color:green; width:520px" %)
283 +|=(% scope="row" style="width: 50px;" %)**Size(bytes)**|(% style="width:40px" %)**8**|(% style="width:20px" %)**2**|(% style="width:25px" %)**2**|(% style="width:60px" %)**1**|(% style="width:20px" %)**1**|(% style="width:40px" %)**1**|(% style="width:40px" %)**2**|(% style="width:50px" %)**2**|(% style="width:50px" %)**4**|(% style="width:50px" %)**2**|(% style="width:30px" %)**2**|(% style="width:40px" %)**4**
284 +|=(% style="width: 96px;" %)**Value**|(% style="width:83px" %)Device ID|(% style="width:44px" %)Ver|(% style="width:42px" %)BAT|(% style="width:124px" %)Signal Strength|(% style="width:57px" %)MOD|(% style="width:80px" %)Interrupt|(% style="width:69px" %)Soil PH|(% style="width:134px" %)Soil Temperature|(% style="width:98px" %)Time stamp|(% style="width:134px" %)Soil Temperature|(% style="width:68px" %)Soil PH|(% style="width:125px" %)Time stamp  .....
236 236  
237 237  If we use the MQTT client to subscribe to this MQTT topic, we can see the following information when the NSPH01 uplink data.
238 238  
239 -(% style="text-align:center" %)
240 240  [[image:image-20220907153902-15.png||height="581" width="804"]]
241 241  
242 242  
291 +(((
243 243  The payload is ASCII string, representative same HEX:
293 +)))
244 244  
245 -0xf86841105675413800640c781701000225010b6315537b010b0226631550fb010e022663154d7701110225631549f1011502246315466b01190223631542e5011d022163153f62011e022163153bde011e022163153859 where:
295 +(((
296 +
297 +)))
246 246  
247 -* Device ID: 0xf868411056754138 = f868411056754138
248 -* Version: 0x0064=100=1.0.0
299 +(((
300 +**0x (% style="color:red" %)__f868411056754138__  (% style="color:blue" %)__0064 __ (% style="color:green" %)__0c78__  (% style="color:#00b0f0" %)__17__  (% style="color:#7030a0" %)__01__  (% style="color:#d60093" %)__00__  (% style="color:#a14d07" %)__0225 __ (% style="color:#0020b0" %) __010b__  (% style="color:#420042" %)__6315537b__  (% style="color:#663300" %)//__010b0226631550fb__  __010e022663154d77  01110225631549f1  011502246315466b  01190223631542e5  011d022163153f62  011e022163153bde 011e022163153859__//(%%)**
301 +)))
249 249  
250 -* BAT: 0x0c78 = 3192 mV = 3.192V
251 -* Singal: 0x17 = 23
252 -* Mod: 0x01 = 1
253 -* Interrupt: 0x00= 0
254 -* Soil PH: 0x0225= 549 = 5.49
255 -* Soil Temperature:0x010B =267=26.7 °C
256 -* Time stamp : 0x6315537b =1662342011
257 -* Soil Temperature,Soil PH,Time stamp : 010b0226631550fb
258 -* 8 sets of recorded data: Temperature,Soil PH,Time stamp : 010e022663154d77,.......
303 +(((
304 +
259 259  
260 -**2.4  Payload Explanation and Sensor Interface**
306 +**where:**
307 +)))
261 261  
262 -**2.4.1  Device ID**
309 +* (% style="color:#037691" %)**Device ID:**(%%)** **0xf868411056754138 = f868411056754138
263 263  
311 +* (% style="color:#037691" %)**Version:**  (%%) 0x0064=100=1.0.0
312 +
313 +* (% style="color:#037691" %)**BAT:**   (%%) 0x0c78 = 3192 mV = 3.192V
314 +
315 +* (% style="color:#037691" %)**Singal:** (%%)0x17 = 23
316 +
317 +* (% style="color:#037691" %)**Mod:** (%%) 0x01 = 1
318 +
319 +* (% style="color:#037691" %)**Interrupt:**(%%) 0x00= 0
320 +
321 +* (% style="color:#037691" %)**Soil PH:** (%%) 0x0225= 549 = 5.49
322 +
323 +* (% style="color:#037691" %)**Soil Temperature:**(%%) 0x010b =267=26.7 °C
324 +
325 +* (% style="color:#037691" %)**Time stamp :**   (%%) 0x6315537b =1662342011  ([[Unix Epoch Time>>url:http://www.epochconverter.com/]])
326 +
327 +* (% style="color:#037691" %)**Soil Temperature,Soil PH,Time stamp : **(%%) 010b0226631550fb
328 +
329 +* (% style="color:#037691" %)**8 sets of recorded data:**(%%) Temperature,Soil PH,Time stamp :  010e022663154d77,.......
330 +
331 +
332 +== 2.4  Payload Explanation and Sensor Interface ==
333 +
334 +
335 +=== 2.4.1  Device ID ===
336 +
337 +
264 264  By default, the Device ID equal to the last 15 bits of IMEI.
265 265  
266 -User can use **AT+DEUI** to set Device ID
340 +User can use (% style="color:blue" %)**AT+DEUI** (%%)to set Device ID
267 267  
342 +
268 268  **Example:**
269 269  
270 270  AT+DEUI=868411056754138
... ... @@ -271,14 +271,20 @@
271 271  
272 272  The Device ID is stored in a none-erase area, Upgrade the firmware or run AT+FDR won't erase Device ID.
273 273  
274 -**2.4.2  Version Info**
275 275  
350 +
351 +=== 2.4.2  Version Info ===
352 +
353 +
276 276  Specify the software version: 0x64=100, means firmware version 1.00.
277 277  
278 278  For example: 0x00 64 : this device is NSPH01 with firmware version 1.0.0.
279 279  
280 -**2.4.3  Battery Info**
281 281  
359 +
360 +=== 2.4.3  Battery Info ===
361 +
362 +
282 282  Check the battery voltage for NSPH01.
283 283  
284 284  Ex1: 0x0B45 = 2885mV
... ... @@ -285,8 +285,11 @@
285 285  
286 286  Ex2: 0x0B49 = 2889mV
287 287  
288 -**2.4.4  Signal Strength**
289 289  
370 +
371 +=== 2.4.4  Signal Strength ===
372 +
373 +
290 290  NB-IoT Network signal Strength.
291 291  
292 292  **Ex1: 0x1d = 29**
... ... @@ -301,18 +301,25 @@
301 301  
302 302  **99**    Not known or not detectable
303 303  
304 -**2.4.5  Soil PH**
305 305  
389 +
390 +=== 2.4.5  Soil PH ===
391 +
392 +
306 306  Get the PH content of the soil. The value range of the register is 300-1000(Decimal), divide this value by 100 to get the percentage of PH in the soil.
307 307  
308 -For example, if the data you get from the register is **__0x05 0xDC__**, the PH content in the soil is
395 +For example, if the data you get from the register is (% style="color:blue" %)**__0x05 0xDC__**(%%), the PH content in the soil is
309 309  
310 -**0229(H) = 549(D) /100 = 5.49.**
397 +(% style="color:blue" %)**0229(H) = 549(D) /100 = 5.49.**
311 311  
312 -**2.4.6  Soil Temperature**
313 313  
314 -Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is **__0x09 0xEC__**, the temperature content in the soil is
315 315  
401 +=== 2.4.6  Soil Temperature ===
402 +
403 +
404 +Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is (% style="color:blue" %)**__0x09 0xEC__**(%%), the temperature content in the soil is
405 +
406 +
316 316  **Example**:
317 317  
318 318  If payload is 0105H: ((0x0105 & 0x8000)>>15 === 0),temp = 0105(H)/10 = 26.1 °C
... ... @@ -319,56 +319,62 @@
319 319  
320 320  If payload is FF7EH: ((FF7E & 0x8000)>>15 ===1),temp = (FF7E(H)-FFFF(H))/10 = -12.9 °C
321 321  
322 -**2.4.7  Timestamp**
323 323  
414 +
415 +=== 2.4.7  Timestamp ===
416 +
417 +
324 324  Time stamp : 0x6315537b =1662342011
325 325  
326 326  Convert Unix timestamp to time 2022-9-5 9:40:11.
327 327  
328 -**2.4.8  Digital Interrupt**
329 329  
330 -Digital Interrupt refers to pin **GPIO_EXTI**, and there are different trigger methods. When there is a trigger, the NSPH01 will send a packet to the server.
331 331  
424 +=== 2.4.8  Digital Interrupt ===
425 +
426 +
427 +Digital Interrupt refers to pin (% style="color:blue" %)**GPIO_EXTI**(%%), and there are different trigger methods. When there is a trigger, the NSPH01 will send a packet to the server.
428 +
332 332  The command is:
333 333  
334 -**AT+INTMOD=3 ** ~/~/(more info about INMOD please refer [[**AT Command Manual**>>url:https://www.dragino.com/downloads/downloads/NB-IoT/NBSN95/DRAGINO_NBSN95-NB_AT%20Commands_v1.1.0.pdf]])**.**
431 +(% style="color:blue" %)**AT+INTMOD=3 ** (%%) ~/~/(more info about INMOD please refer [[**AT Command Manual**>>url:https://www.dragino.com/downloads/downloads/NB-IoT/NBSN95/DRAGINO_NBSN95-NB_AT%20Commands_v1.1.0.pdf]])**.**
335 335  
336 336  The lower four bits of this data field shows if this packet is generated by interrupt or not. Click here for the hardware and software set up.
337 337  
338 -Example:
339 339  
436 +**Example:**
437 +
340 340  0x(00): Normal uplink packet.
341 341  
342 342  0x(01): Interrupt Uplink Packet.
343 343  
344 -**2.4.9  ​+5V Output**
345 345  
443 +
444 +=== 2.4.9  ​+5V Output ===
445 +
446 +
346 346  NSPH01 will enable +5V output before all sampling and disable the +5v after all sampling. 
347 347  
348 348  The 5V output time can be controlled by AT Command.
349 349  
350 -**AT+5VT=1000**
451 +(% style="color:blue" %)**AT+5VT=1000**
351 351  
352 352  Means set 5V valid time to have 1000ms. So the real 5V output will actually have 1000ms + sampling time for other sensors.** **
353 353  
354 354  
355 -**2.5  Downlink Payload**
356 356  
457 +== 2.5  Downlink Payload ==
458 +
459 +
357 357  By default, NSPH01 prints the downlink payload to console port.
358 358  
359 -(% style="text-align:center" %)
360 360  [[image:image-20220907154636-17.png]]
361 361  
362 362  
465 +(% style="color:blue" %)**Examples:**
363 363  
467 +* (% style="color:#037691" %)** Set TDC**
364 364  
365 -
366 -
367 -
368 -**Examples:**
369 -
370 -* **Set TDC**
371 -
372 372  If the payload=0100003C, it means set the END Node's TDC to 0x00003C=60(S), while type code is 01.
373 373  
374 374  Payload:    01 00 00 1E    TDC=30S
... ... @@ -375,16 +375,19 @@
375 375  
376 376  Payload:    01 00 00 3C    TDC=60S
377 377  
378 -* **Reset**
475 +* (% style="color:#037691" %)** Reset**
379 379  
380 -If payload = 0x04FF, it will reset the NSE01
477 +If payload = 0x04FF, it will reset the NSPH01
381 381  
382 -* **INTMOD**
479 +* (% style="color:#037691" %)** INTMOD**
383 383  
384 384  Downlink Payload: 06000003, Set AT+INTMOD=3
385 385  
386 -**2.6  ​LED Indicator**
387 387  
484 +
485 +== 2.6  ​LED Indicator ==
486 +
487 +
388 388  The NSPH01 has an internal LED which is to show the status of different state.
389 389  
390 390  * When power on, NSPH01 will detect if sensor probe is connected, if probe detected, LED will blink four times. (no blinks in this step is no probe)
... ... @@ -392,16 +392,22 @@
392 392  * After NSPH01 join NB-IoT network. The LED will be ON for 3 seconds.
393 393  * For each uplink probe, LED will be on for 500ms.
394 394  
395 -**2.7 Installation and Maintain**
495 +== 2.7  Installation and Maintain ==
396 396  
397 -**2.7.1 Before measurement**
398 398  
498 +=== 2.7.1  Before measurement ===
499 +
500 +
399 399  If the NSPH01 has more than 7 days not use or just clean the pH probe. User should put the probe inside pure water for more than 24 hours for activation. If no put in water, user need to put inside soil for more than 24 hours to ensure the measurement accuracy. 
400 400  
401 -**2.7.2 Measurement**
402 402  
403 -**Measurement the soil surface:**
404 404  
505 +=== 2.7.2  Measurement ===
506 +
507 +
508 +(% style="color:#037691" %)**Measurement the soil surface:**
509 +
510 +
405 405  [[image:image-20220907154700-18.png]] ​
406 406  
407 407  Choose the proper measuring position. Split the surface soil according to the measured deep.
... ... @@ -412,14 +412,18 @@
412 412  
413 413  Put soil over the probe after insert. And start to measure.
414 414  
415 -**Measurement inside soil:**
416 416  
522 +(% style="color:#037691" %)**Measurement inside soil:**
523 +
417 417  Dig a hole with diameter > 20CM.
418 418  
419 419  Insert the probe inside, method like measure the surface.
420 420  
421 -**2.7.3 Maintain Probe**
422 422  
529 +
530 +=== 2.7.3  Maintain Probe ===
531 +
532 +
423 423  1. pH probe electrode is fragile and no strong. User must avoid strong force or hitting it.
424 424  1. After long time use (3~~ 6  months). The probe electrode needs to be clean; user can use high grade sandpaper to polish it or put in 5% hydrochloric acid for several minutes. After the metal probe looks like new, user can use pure water to wash it.
425 425  1. Probe reference electrode is also no strong, need to avoid strong force or hitting.
... ... @@ -427,12 +427,13 @@
427 427  1. Avoid the probes to touch oily matter. Which will cause issue in accuracy.
428 428  1. The probe is IP68 can be put in water.
429 429  
430 -**2.8 PH and Temperature alarm function**
540 +== 2.8  PH and Temperature alarm function ==
431 431  
432 -➢ AT Command:
433 433  
434 -AT+ PHALARM=min,max
543 +(% style="color:#037691" %)**➢ AT Command:**
435 435  
545 +(% style="color:blue" %)**AT+ PHALARM=min,max**
546 +
436 436  ² When min=3, and max≠0, Alarm higher than max
437 437  
438 438  ² When min≠0, and max=0, Alarm lower than min
... ... @@ -439,10 +439,11 @@
439 439  
440 440  ² When min≠0 and max≠0, Alarm higher than max or lower than min
441 441  
442 -Example:
443 443  
444 -AT+ PHALARM =3,5 ~/~/ Alarm when PH lower than 5.
554 +(% style="color:blue" %)**Example:**
445 445  
556 +AT+ PHALARM =5,8  ~/~/ Alarm when PH lower than 5.
557 +
446 446  AT+ TEMPALARM=min,max
447 447  
448 448  ² When min=0, and max≠0, Alarm higher than max
... ... @@ -451,55 +451,71 @@
451 451  
452 452  ² When min≠0 and max≠0, Alarm higher than max or lower than min
453 453  
454 -Example:
455 455  
456 -AT+ TEMPALARM=0,20 ~/~/ Alarm when temperature lower than 20.
567 +(% style="color:blue" %)**Example:**
457 457  
569 +AT+ TEMPALARM=20,30  ~/~/ Alarm when temperature lower than 20.
458 458  
459 -**2.9 Set the number of data to be uploaded and the recording time**
460 460  
461 -➢ AT Command:
462 462  
463 -AT+TR=900  ~/~/The unit is seconds, and the default is to record data once every 900 seconds.( The minimum can be set to 180 seconds)
573 +== 2.9  Set the number of data to be uploaded and the recording time ==
464 464  
465 465  
466 -AT+NOUD=8  ~/~/The device uploads 8 sets of recorded data by default. Up to 32 sets of record data can be uploaded.
576 +(% style="color:#037691" %)**➢ AT Command:**
467 467  
468 -**2.10 Read or Clear cached data**
578 +* (% style="color:blue" %)**AT+TR=900**     (%%) ~/~/  The unit is seconds, and the default is to record data once every 900 seconds.( The minimum can be set to 180 seconds)
579 +* (% style="color:blue" %)**AT+NOUD=8**     (%%) ~/~/  The device uploads 8 sets of recorded data by default. Up to 32 sets of record data can be uploaded.
469 469  
470 -➢ AT Command:
581 + The diagram below explains the relationship between TR, NOUD, and TDC more clearly**:**
471 471  
472 -AT+CDP ~/~/ Read cached data
583 +[[image:image-20221009000933-1.png||height="750" width="1043"]]
473 473  
585 +
586 +
587 +== 2.10  Read or Clear cached data ==
588 +
589 +
590 +(% style="color:#037691" %)**➢ AT Command:**
591 +
592 +* (% style="color:blue" %)**AT+CDP**        (%%) ~/~/  Read cached data
593 +* (% style="color:blue" %)**AT+CDP=0**    (%%) ~/~/  Clear cached data
594 +
474 474  [[image:image-20220907154700-19.png]]
475 475  
476 476  
477 -AT+CDP=0 ~/~/ Clear cached data
478 478  
599 +== 2.11  Calibration ==
479 479  
480 -**2.11 Calibration**
481 481  
482 482  User can do calibration for the probe. It is limited to use below pH buffer solution to calibrate: 4.00, 6.86, 9.18. When calibration, user need to clean the electrode and put the probe in the pH buffer solution to wait the value stable ( a new clean electrode might need max 24 hours to be stable).
483 483  
484 484  After stable, user can use below command to calibrate.
485 485  
606 +
486 486  [[image:image-20220907154700-20.png]] ​
487 487  
488 -**2.8  ​Firmware Change Log**
489 489  
490 -Download URL & Firmware Change log: [[https:~~/~~/www.dropbox.com/sh/1zmcakvbkf24f8x/AACmq2dZ3iRB9F1nVWeEB9Moa?dl=0>>url:https://www.dropbox.com/sh/1zmcakvbkf24f8x/AACmq2dZ3iRB9F1nVWeEB9Moa?dl=0]]
491 491  
492 -Upgrade Instruction: [[Upgrade Firmware>>path:#H5.1200BHowtoUpgradeFirmware]]
611 +== 2.12  ​Firmware Change Log ==
493 493  
494 -**2.9  ​Battery Analysis**
495 495  
496 -**2.9.1  ​Battery Type**
614 +Download URL & Firmware Change log: [[https:~~/~~/www.dropbox.com/sh/1tv07fro2pvjqj8/AAD-2wbfGfluTZfh38fQqdA_a?dl=0>>https://www.dropbox.com/sh/1tv07fro2pvjqj8/AAD-2wbfGfluTZfh38fQqdA_a?dl=0]]
497 497  
616 +Upgrade Instruction: [[Upgrade Firmware>>||anchor="H5.1200BHowtoUpgradeFirmware"]]
617 +
618 +
619 +
620 +== 2.13  ​Battery Analysis ==
621 +
622 +
623 +=== 2.13.1  ​Battery Type ===
624 +
625 +
498 498  The NSPH01 battery is a combination of an 8500mAh Li/SOCI2 Battery and a Super Capacitor. The battery is none-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
499 499  
500 500  The battery is designed to last for several years depends on the actually use environment and update interval. 
501 501  
502 -The battery related documents as below:
630 +The battery-related documents as below:
503 503  
504 504  * [[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
505 505  * [[Lithium-Thionyl Chloride Battery datasheet>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
... ... @@ -507,15 +507,18 @@
507 507  
508 508  [[image:image-20220907154700-21.png]] ​
509 509  
510 -**2.9.2  Power consumption Analyze**
511 511  
639 +
640 +=== 2.13.2  Power consumption Analyze ===
641 +
642 +
512 512  Dragino battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
513 513  
514 514  Instruction to use as below:
515 515  
516 -**Step 1:  **Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/]]
647 +(% style="color:blue" %)**Step 1:  **(%%)Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/]]
517 517  
518 -**Step 2: ** Open it and choose
649 +(% style="color:blue" %)**Step 2: **(%%) Open it and choose
519 519  
520 520  * Product Model
521 521  * Uplink Interval
... ... @@ -523,34 +523,45 @@
523 523  
524 524  And the Life expectation in difference case will be shown on the right.
525 525  
526 -(% style="text-align:center" %)
657 +
527 527  [[image:image-20220907154700-22.jpeg]]
528 528  
529 529  ​
530 530  
531 -**2.9.3  ​Battery Note**
532 532  
663 +=== 2.13.3  ​Battery Note ===
664 +
665 +
533 533  The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
534 534  
535 -**2.9.4  Replace the battery**
536 536  
669 +
670 +=== 2.13.4  Replace the battery ===
671 +
672 +
537 537  The default battery pack of NSPH01 includes a ER26500 plus super capacitor. If user can't find this pack locally, they can find ER26500 or equivalence without the SPC1520 capacitor, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes).
538 538  
539 -**3. ​ Access NB-IoT Module**
540 540  
676 +
677 += 3. ​ Access NB-IoT Module =
678 +
679 +
541 541  Users can directly access the AT command set of the NB-IoT module.
542 542  
543 543  The AT Command set can refer the BC35-G NB-IoT Module AT Command: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/]] 
544 544  
545 -(% style="text-align:center" %)
684 +
546 546  [[image:image-20220907154700-23.png]]
547 547  
548 548  ​
549 549  
550 -**4.  Using the AT Commands**
551 551  
552 -**4.1  Access AT Commands**
690 += 4.  Using the AT Commands =
553 553  
692 +
693 +== 4.1  Access AT Commands ==
694 +
695 +
554 554  See this link for detail:  [[https:~~/~~/www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0>>url:https://www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0]]
555 555  
556 556  AT+<CMD>?  : Help on <CMD>
... ... @@ -561,8 +561,9 @@
561 561  
562 562  AT+<CMD>=?  : Get the value
563 563  
564 -**General Commands**      
565 565  
707 +(% style="color:#037691" %)**General Commands**      
708 +
566 566  AT  : Attention       
567 567  
568 568  AT?  : Short Help     
... ... @@ -587,13 +587,18 @@
587 587  
588 588  AT+TR      : Get or Set record time"
589 589  
733 +AT+APN     : Get or set the APN
590 590  
591 -AT+NOUD      : Get or Set the number of data to be uploaded
735 +AT+FBAND   : Get or Set whether to automatically modify the frequency band
592 592  
737 +AT+DNSCFG  : Get or Set DNS Server
593 593  
594 -AT+CDP     : Read or Clear cached data
739 +AT+GETSENSORVALUE   : Returns the current sensor measurement
595 595  
741 +AT+NOUD      : Get or Set the number of data to be uploaded
596 596  
743 +AT+CDP     : Read or Clear cached data
744 +
597 597  AT+TEMPALARM      : Get or Set alarm of temp
598 598  
599 599  AT+PHALARM     : Get or Set alarm of PH
... ... @@ -601,16 +601,18 @@
601 601  AT+ PHCAL  : calibrate PH value
602 602  
603 603  
604 -**COAP Management**      
752 +(% style="color:#037691" %)**COAP Management**      
605 605  
606 606  AT+URI            : Resource parameters
607 607  
608 -**UDP Management**
609 609  
757 +(% style="color:#037691" %)**UDP Management**
758 +
610 610  AT+CFM          : Upload confirmation mode (only valid for UDP)
611 611  
612 -**MQTT Management**
613 613  
762 +(% style="color:#037691" %)**MQTT Management**
763 +
614 614  AT+CLIENT               : Get or Set MQTT client
615 615  
616 616  AT+UNAME  : Get or Set MQTT Username
... ... @@ -621,54 +621,79 @@
621 621  
622 622  AT+SUBTOPIC  : Get or Set MQTT subscription topic
623 623  
624 -**Information**          
625 625  
775 +(% style="color:#037691" %)**Information**          
776 +
626 626  AT+FDR  : Factory Data Reset
627 627  
628 628  AT+PWORD  : Serial Access Password
629 629  
630 -**​5.  FAQ**
631 631  
632 -**5.1 ​ How to Upgrade Firmware**
633 633  
783 += ​5.  FAQ =
784 +
785 +
786 +== 5.1 ​ How to Upgrade Firmware ==
787 +
788 +
634 634  User can upgrade the firmware for 1) bug fix, 2) new feature release.
635 635  
636 636  Please see this link for how to upgrade:  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList]]
637 637  
638 -**Notice, **NSPH01 **and **NSPH01 **share the same mother board. They use the same connection and method to update.**
793 +(% style="color:red" %)**Notice, NSPH01 and LSPH01 share the same mother board. They use the same connection and method to update.**
639 639  
640 -**5.2  Can I calibrate NSPH01 to different soil types?**
641 641  
796 +
797 +== 5.2  Can I calibrate NSPH01 to different soil types? ==
798 +
799 +
642 642  NSPH01 is calibrated for saline-alkali soil and loamy soil. If users want to use it for other soil, they can calibrate the value in the IoT platform base on the value measured by saline-alkali soil and loamy soil. The formula can be found at [[this link>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/LSE01/Calibrate_to_other_Soil_20220605.pdf]].
643 643  
644 -**6.  Trouble Shooting**
645 645  
646 -**6.1  ​Connection problem when uploading firmware**
647 647  
804 += 6.  Trouble Shooting =
805 +
806 +
807 +== 6.1  ​Connection problem when uploading firmware ==
808 +
809 +
648 648  **Please see: **[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting]]
649 649  
650 -**6.2  AT Command input doesn't work**
651 651  
652 -In the case if user can see the console output but can't type input to the device. Please check if you already include the **ENTER** while sending out the command. Some serial tool doesn't send **ENTER** while press the send key, user need to add ENTER in their string.
653 653  
654 -**7. ​ Order Info**
814 +== 6.2  AT Command input doesn't work ==
655 655  
816 +
817 +In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER** (%%)while press the send key, user need to add ENTER in their string.
818 +
819 +
820 +
821 += 7. ​ Order Info =
822 +
823 +
656 656  Part Number**:** NSPH01
657 657  
658 -**8.  Packing Info**
659 659  
827 +
828 += 8.  Packing Info =
829 +
830 +
660 660  **Package Includes**:
661 661  
662 -* NSPH01 NB-IoT Soil Moisture & EC Sensor x 1
833 +* NSPH01 NB-IoT pH Sensor x 1
663 663  * External antenna x 1
664 664  
665 665  **Dimension and weight**:
666 666  
667 -* Size: 195 x 125 x 55 mm
668 -* Weight:   420g
838 +* Device Size: cm
839 +* Device Weight: g
840 +* Package Size / pcs : cm
841 +* Weight / pcs : g
669 669  
670 -**9.  Support**
671 671  
844 += 9.  Support =
845 +
846 +
672 672  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
673 673  * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]
674 674  
image-20220912144017-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +149.6 KB
Content
image-20220923101327-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +12.1 KB
Content
image-20221009000933-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Edwin
Size
... ... @@ -1,0 +1,1 @@
1 +282.9 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0