Last modified by Mengting Qiu on 2024/04/02 17:03
<
From version < 47.1 >
edited by David Huang
on 2022/10/24 10:33
To version < 80.1 >
edited by Xiaoling
on 2022/12/07 17:44
>
Change comment: Uploaded new attachment "1670406261143-723.png", version {1}

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -CPN01- NB-IoT Outdoor Open/Close Dry Contact Sensor User Manual
1 +NMDS200 - NB-IoT Microwave Radar Distance Sensor User Manual
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.David
1 +XWiki.Xiaoling
Content
... ... @@ -1,34 +1,46 @@
1 1  (% style="text-align:center" %)
2 -[[image:http://wiki.dragino.com/xwiki/bin/download/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/CPL01%20LoRaWAN%20Outdoor%20PulseContact%20%20Sensor%20Manual/WebHome/1652856952171-363.png?rev=1.1||alt="1652856952171-363.png" height="578" width="588"]]
2 +[[image:LMDS200_10.jpg]]
3 3  
4 -{{toc/}}
5 5  
6 -= **1. Introduction** =
5 +**Table of Contents：**
7 7  
8 -== **1.1 ​**What is CPN01 **NB-IoT** Pulse/Contact Sensor ==
9 9  
10 -The Dragino CPN01 is an (% style="color:blue" %)**NB-IoT Dry Contact Sensor**(%%). It detects open/close status and uplinks the info to IoT server via NB-IoT network. User can see the (% style="color:blue" %)**dry contact status, open time, and open counts**(%%) in the IoT Server.
11 11  
12 -The CPN01 will send periodically data every day as well as for each dry contact action. It also counts the contact open times and calculates the last open duration. Users can also disable the uplink for each Open/Close event, instead, device can count each open event and uplink periodically.
13 13  
14 -CPN01 has** (% style="color:blue" %)Open-Alarm feature(%%)**, user can set this feature so CPN01 will send an alarm if the contact has been open exceeds a certain time.
15 15  
16 -CPN01 is designed for outdoor use. It has a weatherproof enclosure and industrial-level battery to work in low to high temperatures.
11 += 1.  Introduction =
17 17  
18 -NarrowBand-Internet of Things (NB-IoT) is a standards-based low power wide area (LPWA) technology developed to enable a wide range of new IoT devices and services. NB-IoT significantly improves the power consumption of user devices, system capacity, and spectrum efficiency, especially in deep coverage.
19 -\\CPN01 supports different uplink methods including (% style="color:blue" %)**TCP, MQTT, UDP, and CoAP**(%%) for different application requirements.
20 -\\CPN01 is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), It is designed for long-term use of up to 5 years. (Actually Battery life depends on the use environment, update period & uplink method)
21 -\\To use CPN01, user needs to check if there is NB-IoT coverage in the field and with the Nb-IoT bands that CPN01 supports. If local operator support it, user needs to get a (% style="color:blue" %)**NB-IoT SIM card**(%%) from the operator and install into CPN01 to get NB-IoT network connection.
13 +== 1.1 ​ What is NMDS200 NB-IoT Microwave Radar Distance Sensor ==
22 22  
23 -​
24 24  
25 -== **​1.2 Features** ==
16 +(((
17 +The Dragino NMDS200 is a(% style="color:blue" %)** NB-IoT Microwave Radar distance sensor**(%%). It uses (% style="color:blue" %)**24Ghz Microwave**(%%) to detect the distance between sensor and different objects. Compare vs ultrasonic or Lidar measurement method, Microwave Radar is (% style="color:blue" %)**more reliable for condensation / dusty environment**(%%). It can sense correct distance even there is water or thick dust on top of the sensor.
26 26  
19 +
20 +The NMDS200 can be applied to scenarios such as horizontal distance measurement, parking management system, object proximity and presence detection, intelligent trash can management system, robot obstacle avoidance, automatic control, sewer, etc.
21 +
22 +NMDS200 can (% style="color:blue" %)**measure two distances**(%%): the closest object and next object behind the closest one.
23 +
24 +NMDS200 (% style="color:blue" %)**supports Alarm Feature**(%%), user can set the NMDS200 to uplink data in a short interval when the distance is out of configured range.
25 +
26 +NarrowBand-Internet of Things (NB-IoT) is a (% style="color:blue" %)**standards-based low power wide area (LPWA) technology**(%%) developed to enable a wide range of new IoT devices and services. NB-IoT significantly improves the power consumption of user devices, system capacity, and spectrum efficiency, especially in deep coverage.
27 +
28 +NMDS200 (% style="color:blue" %)**supports different uplink**(%%) methods including (% style="color:blue" %)**TCP, MQTT, UDP, and CoAP**(%%) for different application requirements.
29 +
30 +NMDS200 is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**,(%%) It is designed for long-term use of up to 5 years. (Actually Battery life depends on the use environment, update period & uplink method)
31 +
32 +To use NMDS200, user needs to check if there is NB-IoT coverage in the field and with the Nb-IoT bands that NMDS200 supports. If local operator support it, user needs to get a** (% style="color:blue" %)NB-IoT SIM card(%%)** from the operator and install into NMDS200 to get NB-IoT network connection.
33 +)))
34 +
35 +
36 +
37 +== ​1.2  Features ==
38 +
39 +
27 27  * NB-IoT Bands: B1/B3/B8/B5/B20/B28 @H-FDD
28 -* Open/Close detect
29 -* Open/Close statistics
41 +* Short uplink interval for Distance Alarm
30 30  * Monitor Battery Level
31 -* Uplink on periodically and open/close event
43 +* Microwave Radar for distance detection
32 32  * Datalog feature
33 33  * Uplink periodically
34 34  * Downlink to change configure
... ... @@ -39,106 +39,112 @@
39 39  * Micro SIM card slot for NB-IoT SIM
40 40  * 8500mAh Battery for long-term use
41 41  
42 -== **1.3  Specification** ==
43 43  
44 -**Common DC Characteristics:**
45 45  
46 -* Supply Voltage: 2.1v ~~ 3.6v
47 -* Operating Temperature: -40 ~~ 85°C
56 +== 1.3 Radar probe specification ==
48 48  
49 -**NB-IoT Spec:**
50 50  
51 -* - B1 @H-FDD: 2100MHz
52 -* - B3 @H-FDD: 1800MHz
53 -* - B8 @H-FDD: 900MHz
54 -* - B5 @H-FDD: 850MHz
55 -* - B20 @H-FDD: 800MHz
56 -* - B28 @H-FDD: 700MHz
59 +* Measuring Method: FMCW
60 +* Frequency: 24.000 24.500 GHz
61 +* Measurement output power: 6dBm
62 +* Measure range: 0.5 20m
63 +* Accuracy: ±0.1m
64 +* Resolution: 0.01m
65 +* Horizontal Angel: 78°
66 +* Vertical Angel: 23°
57 57  
58 -== **1.4 Installation** ==
59 59  
60 -Connect CPN01 to an Open Close sensor like below. So it can detect the Open/Close event.
61 61  
62 -[[image:image-20221021110329-1.png]]
63 63  
64 -[[image:image-20221022234602-2.png||height="288" width="922"]]
71 +== 1.4  Storage Temperature ==
65 65  
66 66  
67 -== **1.5 ​Applications** ==
74 + -40°C to +85°C
68 68  
69 -* Open/Close Detection
70 -* Pulse meter application
71 -* Dry Contact Detection
72 72  
73 -== **1.6 Mechanical** ==
74 74  
75 -​[[image:image-20221021110415-3.png]]
76 76  
77 -== ** 1.7 Pin Definitions and Switch** ==
78 78  
79 -[[image:image-20221021110429-4.png]]
80 +== 1.5 ​ Applications ==
80 80  
81 -=== **1.7.1 Pin Definition** ===
82 82  
83 -CPN01 is pre-configured to connect to two external wires. The other pins are not used. If user wants to know more about other pins, please refer to the **[[LSN50v2 User Manual>>doc:Main.User Manual for LoRaWAN End Nodes.LSN50 & LSN50-V2 - LoRaWAN Sensor Node User Manual.WebHome]]**.
84 84  
84 +* Horizontal distance measurement
85 +* Liquid level measurement
86 +* Parking management system
87 +* Object proximity and presence detection
88 +* Intelligent trash can management system
89 +* Robot obstacle avoidance
90 +* Automatic control
91 +* Sewer
92 +* Bottom water level monitoring
85 85  
86 -=== **1.7.2 Jumper JP2(Power ON/OFF)** ===
87 87  
88 -Power on Device when putting this jumper.
89 89  
96 +== 1.6  Specification ==
90 90  
91 -=== **1.7.3 BOOT MODE / SW1** ===
92 92  
99 +(% style="color:blue" %)**Common DC Characteristics:**
93 93  
94 -1) ISP: upgrade mode, device won't have any signal in this mode. but ready for upgrade firmware. LED won't work. The firmware won't run.
101 +* Supply Voltage: 2.1v ~~ 3.6v
102 +* Operating Temperature: 0 ~~ 70°C
95 95  
96 -2) Flash: working mode, the device starts to work for NB-IoT connection and sends out console output for further debugging.
104 +(% style="color:blue" %)**NB-IoT Spec:**
97 97  
106 +* B1 @H-FDD: 2100MHz
107 +* B3 @H-FDD: 1800MHz
108 +* B8 @H-FDD: 900MHz
109 +* B5 @H-FDD: 850MHz
110 +* B20 @H-FDD: 800MHz
111 +* B28 @H-FDD: 700MHz
98 98  
99 -=== **1.7.4 Reset Button** ===
100 100  
101 101  
102 -Press to reboot the device.
115 +== 1.7  Installation ==
103 103  
104 104  
105 -=== **1.7.5 LED** ===
118 +Sensor measure direction and angle is as below. When install the sensor, please make sure the sensor direct to object.
106 106  
107 107  
108 -The LED will blink when :
121 +[[image:image-20221207170748-1.png]] [[image:image-20221207170748-2.png||height="366" width="672"]]
109 109  
110 -1. Boot the device in flash mode
111 -1. Send an uplink packet
112 112  
113 -= **2.  Use CPN01 to communicate with IoT Server** =
114 114  
115 -== **2.1  How it works** ==
125 +== 1.8  Pin Definitions and Switch ==
116 116  
117 -The CPN01 is equipped with an NB-IoT module, the pre-loaded firmware in CPN01 will get **Open/Close Event or Count** from sensor and send the value to the NB-IoT network. The NB-IoT network will forward this value to IoT server via the protocol defined by CPN01.
118 118  
119 -The diagram below shows the working flow in the default firmware of CPN01:
128 +[[image:1670404362039-351.png]]
120 120  
130 +
131 += 2.  Use NMDS200 to communicate with IoT Server =
132 +
133 +== 2.1  How it works ==
134 +
135 +
136 +The NB-IoT network will forward this value to IoT server via the protocol defined by NMDS200.
137 +
138 +The diagram below shows the working flow in the default firmware of NMDS200:
139 +
121 121  [[image:image-20221021110615-5.png]]
122 122  
123 123  
124 -== **2.2 ​ Configure CPN01** ==
143 +== 2.2 ​ Configure NMDS200 ==
125 125  
126 -=== **2.2.1 Test Requirement** ===
127 127  
128 -To use CPN01 in your city, make sure to meet below requirements:
146 +To use NMDS200 in your city, make sure to meet below requirements:
129 129  
130 130  * Your local operator has already distributed an NB-IoT Network.
131 -* The local NB-IoT network used the band that CPN01 supports.
149 +* The local NB-IoT network used the band that NMDS200 supports.
132 132  * Your operator is able to distribute the data received in their NB-IoT network to your IoT server.
133 133  
134 -Below figure shows our testing structure. Here we have NB-IoT network coverage by China Mobile, the band they use is B8.  The CPN01 will use CoAP(120.24.4.116:5683) or raw UDP(120.24.4.116:5601) or MQTT(120.24.4.116:1883)or TCP(120.24.4.116:5600)protocol to send data to the test server.
152 +Below figure shows our testing structure. Here we have NB-IoT network coverage by China Mobile, the band they use is B8.  The NMDS200 will use** (% style="color:red" %)CoAP(120.24.4.116:5683)(%%)** or raw (% style="color:red" %)**UDP(120.24.4.116:5601) **(%%)or (% style="color:red" %)**MQTT(120.24.4.116:1883) **(%%)or (% style="color:red" %)**TCP(120.24.4.116:5600)protocol**(%%) to send data to the test server.
135 135  
136 -[[image:image-20221023000439-3.png]]
154 +[[image:image-20221207173300-4.png]]
137 137  
138 - ​
139 139  
140 -=== **2.2.2 Insert NB-IoT SIM card** ===
157 +=== 2.2.1 Insert NB-IoT SIM card ===
141 141  
159 +
142 142  Insert the NB-IoT Card get from your provider.
143 143  
144 144  User needs to take out the NB-IoT module and insert the SIM card like below:
... ... @@ -146,174 +146,217 @@
146 146  [[image:image-20221021110745-6.png]] ​
147 147  
148 148  
149 -=== **2.2.3 Connect USB – TTL to CPN01 and configure it** ===
167 +=== 2.2.2 Connect USB – TTL to NMDS200 and configure it ===
150 150  
151 -User need to configure CPN01 via serial port to set the **Server Address** / **Uplink Topic** to define where and how-to uplink packets. CPN01 support AT Commands, user can use a USB to TTL adapter to connect to CPN01 and use AT Commands to configure it, as below.
152 152  
153 -**Connection:**
170 +User need to configure NMDS200 via serial port to set the (% style="color:red" %)**Server Address** / **Uplink Topic**(%%) to define where and how-to uplink packets. NMDS200 support AT Commands, user can use a USB to TTL adapter to connect to NMDS200 and use AT Commands to configure it, as below.
154 154  
155 - USB TTL GND <~-~-~-~-> GND
172 +(% style="color:blue" %)**Connection:**
156 156  
157 - USB TTL TXD <~-~-~-~-> UART_RXD
174 +(% style="background-color:yellow" %)** USB TTL GND <~-~-~-~-> GND**
158 158  
159 - USB TTL RXD <~-~-~-~-> UART_TXD
176 +(% style="background-color:yellow" %)** USB TTL TXD <~-~-~-~-> UART_RXD**
160 160  
178 +(% style="background-color:yellow" %)** USB TTL RXD <~-~-~-~-> UART_TXD**
179 +
180 +
161 161  In the PC, use below serial tool settings:
162 162  
163 -* Baud:  **9600**
164 -* Data bits:** 8**
165 -* Stop bits: **1**
166 -* Parity:  **None**
167 -* Flow Control: **None**
183 +* Baud:  (% style="color:red" %)**9600**
168 168  
169 -Make sure the switch is in FLASH position, then power on CPN01 by connecting the (% style="color:orange" %)**Yellow Jumper**(%%).
185 +* Data bits:** (% style="color:red" %)8(%%)**
170 170  
187 +* Stop bits: (% style="color:red" %)**1**
188 +
189 +* Parity:  (% style="color:red" %)**None**
190 +
191 +* Flow Control: (% style="color:red" %)**None**
192 +
193 +Make sure the switch is in FLASH position, then power on NMDS200 by connecting the (% style="color:orange" %)**Yellow Jumper**(%%).
194 +
171 171  ​[[image:image-20221021110817-7.png]]
172 172  
173 -CPN01 will output system info once powered on as below, we can enter the **password: 12345678** to access AT Command input.
197 +NMDS200 will output system info once powered on as below, we can enter the **password: 12345678** to access AT Command input.
174 174  
175 175  
176 -**Note: the valid AT Commands can be found at:  **[[**https:~~/~~/www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0**>>url:https://www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0]]
200 +(% style="color:red" %)**Note: the valid AT Commands can be found at:  **(%%)[[**https:~~/~~/www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0**>>url:https://www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0]]
177 177  
178 178  
179 -=== **2.2.4 Use CoAP protocol to uplink data** ===
180 180  
181 -**Note: if you don't have a CoAP server, you can refer this link to set up a CoAP server: **[[**http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/**>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/]]
204 +=== 2.2.3 Use CoAP protocol to uplink data ===
182 182  
183 183  
184 -**Use below commands in CPN01:**
207 +(% style="color:red" %)**Note: if you don't have a CoAP server, you can refer this link to set up a CoAP server: **(%%)[[**http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/**>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/]]
185 185  
186 -* **AT+PRO=1**   ~/~/ Set to use CoAP protocol to uplink
187 -* **AT+SERVADDR=120.24.4.116,5683   ** ~/~/ Set CoAP server address and port
188 -* **AT+URI=0,0,11,2,"mqtt" ** ~/~/Set CoAP resource path
189 189  
210 +(% style="color:blue" %)**Use below commands in NDS03A:**
211 +
212 +* (% style="color:#037691" %)**AT+PRO=1**                (%%) ~/~/ Set to use CoAP protocol to uplink
213 +
214 +* (% style="color:#037691" %)**AT+SERVADDR=120.24.4.116,5683   ** (%%) ~/~/ Set CoAP server address and port
215 +
216 +* (% style="color:#037691" %)**AT+URI=0,0,11,2,"mqtt" ** (%%) ~/~/  Set CoAP resource path
217 +
190 190  For parameter description, please refer to AT command set
191 191  
192 192  [[image:image-20221021110948-8.png]]
193 193  
194 194  
195 -After configuring the server address and **reset CPN01** (via AT+ATZ ), CPN01 will start to uplink sensor values to the CoAP server.
223 +After configuring the server address and (% style="color:green" %)**reset NMDS200**(%%) (via AT+ATZ ), NMDS200 will start to uplink sensor values to the CoAP server.
196 196  
197 -[[image:image-20221021110956-9.png]] ​
225 +[[image:1670405841875-916.png]] ​
198 198  
199 199  
200 -=== **2.2.5 Use UDP protocol to uplink data(Default protocol)** ===
228 +=== 2.2.4 Use UDP protocol to uplink data(Default protocol) ===
201 201  
202 202  
203 -**AT Commands:**
231 +(% style="color:blue" %)**AT Commands:**
204 204  
205 -* **AT+PRO=2   ** ~/~/ Set to use UDP protocol to uplink
206 -* **AT+SERVADDR=120.24.4.116,5601   ** ~/~/ Set UDP server address and port
207 -* **AT+CFM=1       ** ~/~/If the server does not respond, this command is unnecessary
233 +* (% style="color:#037691" %)**AT+PRO=2   ** (%%) ~/~/  Set to use UDP protocol to uplink
208 208  
235 +* (% style="color:#037691" %)**AT+SERVADDR=120.24.4.116,5601   ** (%%) ~/~/  Set UDP server address and port
236 +
237 +* (% style="color:#037691" %)**AT+CFM=1       ** (%%) ~/~/  If the server does not respond, this command is unnecessary
238 +
209 209  ​ [[image:image-20221021111025-10.png]]
210 210  
241 +
211 211  [[image:image-20221021111033-11.png||height="241" width="576"]]
212 212  
213 213  ​
214 214  
215 -=== **2.2.6 Use MQTT protocol to uplink data** ===
246 +=== 2.2.5 Use MQTT protocol to uplink data ===
216 216  
217 217  
218 -**AT Commands:**
249 +(% style="color:blue" %)**AT Commands:**
219 219  
220 -* **AT+PRO=3   ** ~/~/Set to use MQTT protocol to uplink
221 -* **AT+SERVADDR=120.24.4.116,1883   ** ~/~/Set MQTT server address and port
222 -* **AT+CLIENT=CLIENT       ** ~/~/Set up the CLIENT of MQTT
223 -* **AT+UNAME=UNAME                               **~/~/Set the username of MQTT
224 -* **AT+PWD=PWD                                        **~/~/Set the password of MQTT
225 -* **AT+PUBTOPIC=NSE01_PUB                    **~/~/Set the sending topic of MQTT
226 -* **AT+SUBTOPIC=NSE01_SUB          ** ~/~/Set the subscription topic of MQTT
251 +* (% style="color:#037691" %)**AT+PRO=3   ** (%%) ~/~/  Set to use MQTT protocol to uplink
227 227  
228 -​ [[image:image-20221021111058-12.png]]
253 +* (% style="color:#037691" %)**AT+SERVADDR=120.24.4.116,1883   ** (%%) ~/~/  Set MQTT server address and port
229 229  
230 -[[image:image-20221021111201-16.png||height="472" width="653"]]
255 +* (% style="color:#037691" %)**AT+CLIENT=CLIENT       ** (%%) ~/~/  Set up the CLIENT of MQTT
231 231  
257 +* (% style="color:#037691" %)**AT+UNAME=UNAME                     **(%%)** **~/~/  Set the username of MQTT
258 +
259 +* (% style="color:#037691" %)**AT+PWD=PWD                         **(%%)** **~/~/  Set the password of MQTT
260 +
261 +* (% style="color:#037691" %)**AT+PUBTOPIC=NSE01_PUB              **(%%)** **~/~/  Set the sending topic of MQTT
262 +
263 +* (% style="color:#037691" %)**AT+SUBTOPIC=NSE01_SUB          ** (%%) ~/~/  Set the subscription topic of MQTT
264 +
265 +​ [[image:image-20221118103445-7.png]]
266 +
267 +
268 +[[image:1670405928926-116.png]]
269 +
232 232  ​
233 233  
234 234  MQTT protocol has a much higher power consumption compare with UDP / CoAP protocol. Please check the power analyze document and adjust the uplink period to a suitable interval.
235 235  
236 236  
237 -=== **2.2.7 Use TCP protocol to uplink data** ===
275 +=== 2.2.6 Use TCP protocol to uplink data ===
238 238  
239 -**AT Commands**
240 240  
241 -* **AT+PRO=4   ** ~/~/ Set to use TCP protocol to uplink
242 -* **AT+SERVADDR=120.24.4.116,5600   ** ~/~/ Set TCP server address and port
278 +(% style="color:blue" %)**AT Commands:**
243 243  
244 -​ [[image:image-20221021111125-14.png]]
280 +* (% style="color:#037691" %)**AT+PRO=4   ** (%%) ~/~/  Set to use TCP protocol to uplink
245 245  
282 +* (% style="color:#037691" %)**AT+SERVADDR=120.24.4.116,5600   ** (%%) ~/~/  Set TCP server address and port
283 +
284 +​ [[image:1670406036256-101.png||height="676" width="713"]]
285 +
286 +
246 246  [[image:image-20221021111131-15.png]]
247 247  
248 248  ​
249 249  
250 -=== **2.2.8 Change Update Interval** ===
291 +=== 2.2.7 Change Update Interval ===
251 251  
252 -User can use below command to change the **uplink interval**.
253 253  
254 -* **AT+TDC=7200      ** ~/~/ Set Update Interval to 7200s (2 hours)
294 +User can use below command to change the (% style="color:blue" %)**uplink interval**.
255 255  
256 -**NOTE:**
296 +* (% style="color:#037691" %)**AT+TDC=7200      ** (%%) ~/~/ Set Update Interval to 7200s (4 hours)
257 257  
258 -**~1. By default, the device will send an uplink message every 1 hour.**
298 +(% style="color:red" %)**NOTE:**
259 259  
300 +1.  By default, the device will send an uplink message every 4 hour.
260 260  
261 -== **2.3  Uplink Payload** ==
262 262  
263 -The uplink payload includes 123 bytes in total by default.
303 +== 2.3  Uplink Payload ==
264 264  
265 -Each time the device uploads a data package, 8 sets of recorded data will be attached. Up to 32 sets of recorded data can be uploaded.
266 266  
267 -|**Size(bytes)**|**8**|**2**|**2**|**1**|**1**|**1**|**1**|**1**|**3**
268 -|**Value**|[[Device ID>>path:#H2.4.1A0A0DeviceID]]|[[Ver>>path:#H2.4.2A0VersionInfo]]|[[BAT>>path:#H2.4.3A0BatteryInfo]]|[[Signal Strength>>path:#H2.4.4A0SignalStrength]]|MOD|[[ Calculate Flag>>path:#H2.4.8A0DigitalInterrupt]]|Contact Status|Alarm|Total pulse
306 +The uplink payload includes 26 bytes in total by default.
269 269  
270 -(% style="width:1201px" %)
271 -|**3**|**4**|**1**|**3**|**1**|**3**|4|**8 group**|(% style="width:1px" %)
272 -|The last open duration|Time stamp|Contact Status|Total pulse|Calculate Flag|The last open duration|Time stamp|...|(% style="width:1px" %)
308 +Each time the device uploads a data package. The user can use the AT+NOUD command to upload the recorded data.Up to 32 sets of recorded data can be uploaded.
273 273  
274 -If we use the MQTT client to subscribe to this MQTT topic, we can see the following information when the CPN01 uplink data.
310 +(% style="color:blue" %)**When AT+TTRCHANNEL=1:**
275 275  
276 -[[image:image-20221021111201-16.png||height="572" width="792"]]
312 +(% border="1" cellspacing="5" style="background-color:#ffffcc; color:green; width:510px" %)
313 +|=(% scope="row" style="width: 50px;" %)**Size(bytes)**|(% style="width:50px" %)**8**|(% style="width:20px" %)**2**|(% style="width:20px" %)**2**|(% style="width:65px" %)**1**|(% style="width:25px" %)**1**|(% style="width:50px" %)**1**|(% style="width:60px" %)**1**|(% style="width:90px" %)**3**|(% style="width:100px" %)**3**
314 +|=(% style="width: 93px;" %)**Value**|(% style="width:67px" %)[[Device ID>>||anchor="H2.4.1A0A0DeviceID"]]|(% style="width:40px" %)[[Ver>>||anchor="H2.4.2A0VersionInfo"]]|(% style="width:45px" %)[[BAT>>||anchor="H2.4.3A0BatteryInfo"]]|(% style="width:75px" %)[[Signal Strength>>||anchor="H2.4.4A0SignalStrength"]]|(% style="width:54px" %)MOD|(% style="width:62px" %)Door Status|(% style="width:60px" %)[[Alarm Status>>||anchor="H2.7A0AlarmBaseonTimeout"]]|(% style="width:94px" %)door open num(pb14) |(% style="width:93px" %)last open time(pb14)
277 277  
278 -The payload is ASCII string, representative same HEX:
316 +(% border="1.5" style="background-color:#ffffcc; color:green; width:450px" %)
317 +|(% style="width:50px" %)**4**|(% style="width:90px" %)**1**|(% style="width:90px" %)**3**|(% style="width:90px" %)**3**|(% style="width:60px" %)4|(% style="width:50px" %)(((
318 +**1-32 group**
319 +)))
320 +|(% style="width:98px" %)[[Time stamp>>||anchor="H2.4.7A0Timestamp"]]|(% style="width:115px" %)Door Status(pb14)|(% style="width:92px" %)door open num(pb14)|(% style="width:99px" %)last open time(pb14)|(% style="width:67px" %)Time stamp|(% style="width:74px" %)...
279 279  
280 -**0x (% style="color:red" %)__0xf867787050213317__  (% style="color:blue" %)__0064__ (% style="color:green" %)_0c78__  __(% style="color:#00b0f0" %)17__  __(% style="color:#7030a0" %)01__  __(% style="color:#d60093" %)00__  __(% style="color:#a14d07" %)01 __ __(% style="color:#0020b0" %)__ __00__  __(% style="color:#420042" %)000009__  __(% style="color:#663300" %) 000002__  __(% style="color:#d60093" %)6315537bb__  __(% style="color:#663300" %)// 0100000b02000002663510fed__  __0100000e0200000263510f39 010000000000000063510e85 010000000000000063510d2e 010000000000000063510c7a 010000000000000063510bc6 010000000000000063510954 010000000000000063510882 //(%%)**
322 +(% style="color:blue" %)**When AT+TTRCHANNEL=2:**
281 281  
282 -where:
283 -*(% style="color:#037691" %) **Device ID:**(%%) 0x f867787050213317 = f867787050213317
284 284  
285 -*(% style="color:#037691" %) **Version:**(%%) 0x0064=100=1.0.0
325 +(% border="1" cellspacing="5" style="background-color:#ffffcc; color:green; width:510px" %)
326 +|=(% scope="row" style="width: 50px;" %)**Size(bytes)**|(% style="width:45px" %)**8**|(% style="width:20px" %)**2**|(% style="width:20px" %)**2**|(% style="width:65px" %)**1**|(% style="width:25px" %)**1**|(% style="width:60px" %)**1**|(% style="width:60px" %)**1**|(% style="width:87px" %)**3**|(% style="width:80px" %)**3**
327 +|=(% style="width: 96px;" %)**Value**|(% style="width:66px" %)[[Device ID>>||anchor="H2.4.1A0A0DeviceID"]]|(% style="width:40px" %)[[Ver>>||anchor="H2.4.2A0VersionInfo"]]|(% style="width:46px" %)[[BAT>>||anchor="H2.4.3A0BatteryInfo"]]|(% style="width:70px" %)[[Signal Strength>>||anchor="H2.4.4A0SignalStrength"]]|(% style="width:54px" %)MOD|(% style="width:55px" %)Door Status(pb14)|(% style="width:57px" %)[[Alarm Status>>||anchor="H2.7A0AlarmBaseonTimeout"]](pb14)|(% style="width:86px" %)door open num(pb14) |(% style="width:82px" %)last open time(pb14)
286 286  
287 -*(% style="color:#037691" %) **BAT:**(%%) 0x0c78 = 3192 mV = 3.192V
329 +(% border="1" cellspacing="5" style="background-color:#ffffcc; color:green; width:510px" %)
330 +|(% style="width:80px" %)**1**|(% style="width:80px" %)**1**|(% style="width:88px" %)**3**|(% style="width:81px" %)**3**|(% style="width:50px" %)**4**|(% style="width:75px" %)**1**|(% style="width:75px" %)**3**
331 +|(% style="width:59px" %)Door Status(pb15)|(% style="width:67px" %)[[Alarm Status>>||anchor="H2.7A0AlarmBaseonTimeout"]](pb15)|(% style="width:88px" %)door open num(pb15)|(% style="width:81px" %)last open time(pb15)|(% style="width:50px" %)[[Time stamp>>||anchor="H2.4.7A0Timestamp"]]|(% style="width:66px" %)Door Status(pb14)|(% style="width:92px" %)door open num(pb14)
288 288  
289 -*(% style="color:#037691" %) **Singal: **(%%)0x17 = 23
333 +(% border="1" cellspacing="5" style="background-color:#ffffcc; color:green; width:510px" %)
334 +|(% style="width:100px" %)**3**|(% style="width:80px" %)**1**|(% style="width:90px" %)**3**|(% style="width:90px" %)**3**|(% style="width:70px" %)**4**|(% style="width:80px" %)(((
335 +**1-32 group**
336 +)))
337 +|(% style="width:102px" %)last open time(pb14)|(% style="width:93px" %)Door Status(pb15)|(% style="width:91px" %)door open num(pb15)|(% style="width:100px" %)last open time(pb15)|(% style="width:63px" %)[[Time stamp>>||anchor="H2.4.7A0Timestamp"]]|(% style="width:87px" %)......
290 290  
291 -*(% style="color:#037691" %) **Mod:**(%%) 0x01 = 1
339 +If we use the MQTT client to subscribe to this MQTT topic, we can see the following information when the NDS03A uplink data.
292 292  
293 -*(% style="color:#037691" %) **Calculate Flag:**(%%) 0x00=0
341 +[[image:image-20221117145932-2.png]]
294 294  
295 -*(% style="color:#037691" %) **Contact Status:**(%%) 0x00=0
296 296  
297 -*(% style="color:#037691" %) **Alarm:**(%%)0x00 =0
344 +The payload is ASCII string, representative same HEX:
298 298  
299 -*(% style="color:#037691" %) **Total pulse:0x09 =0**
346 +**0x (% style="color:red" %)__f867787050213317__  (% style="color:blue" %)__0064__ (% style="color:green" %) __0ccf__(% style="color:#00b0f0" %) __19__(% style="color:#7030a0" %) __01__(% style="color:#0020b0" %) __00__ (% style="color:#420042" %)__00__(% style="color:#660066" %) (% style="color:#aaaa40" %)__000016__(% style="color:#663300" %) __000017__ (% style="color:#d60093" %)__637590df__(%%)**
300 300  
301 -*(% style="color:#037691" %) **The last open duration:**(%%)0x02 =2
348 +**where:**
302 302  
303 -*(% style="color:#037691" %)** Time stamp :**(%%) 0x6315537b =1662342011 (Unix Time)
350 +* (% style="color:#037691" %)**Device ID:**(%%) 0x f867787050213317 = f867787050213317
304 304  
305 -*(% style="color:#037691" %) **Contact Status, Total pulse, Calculate Flag, The last open duration ,Time stamp :**(%%) 01  00000b  02  000026  63510fed
352 +* (% style="color:#037691" %)**Version:**(%%)  0x0064=100=1.0.0
306 306  
307 -*(% style="color:#037691" %) **8 sets of recorded data: Contact Status, Total pulse, Calculate Flag, The last open duration ,Time stamp :**(%%) 0100000e0200002663510f39,.......
354 +* (% style="color:#037691" %)**BAT :**(%%)  0x0ccf = 3279 mV = 3.279V
308 308  
356 +* (% style="color:#037691" %)**Singal: **(%%)0x19 = 25
309 309  
310 -== **2.4  Payload Explanation and Sensor Interface** ==
358 +* (% style="color:#037691" %)**Mod:**(%%)  0x01 = 1
311 311  
312 -=== **2.4.1  Device ID** ===
360 +* (% style="color:#037691" %)**Door Status:**(%%)  0x00=0
313 313  
362 +* (% style="color:#037691" %)**Alarm Status: **(%%)0x00 =0
363 +
364 +* (% style="color:#037691" %)**door open num: **(%%)0x000016 =22
365 +
366 +* (% style="color:#037691" %)**last open time:   **(%%)0x000017 =23
367 +
368 +* (% style="color:#037691" %)**Timestamp:**(%%) 0x637590df =1668649183 (Unix Time)
369 +
370 +== 2.4  Payload Explanation and Sensor Interface ==
371 +
372 +=== 2.4.1  Device ID ===
373 +
374 +
314 314  By default, the Device ID is equal to the last 15 bits of IMEI.
315 315  
316 -User can use **AT+DEUI** to set Device ID
377 +User can use (% style="color:blue" %)**AT+DEUI** (%%)to set Device ID
317 317  
318 318  **Example:**
319 319  
... ... @@ -322,24 +322,27 @@
322 322  The Device ID is stored in a non-erase area, Upgrade the firmware or run AT+FDR won't erase the Device ID.
323 323  
324 324  
325 -=== **2.4.2  Version Info** ===
386 +=== 2.4.2  Version Info ===
326 326  
388 +
327 327  Specify the software version: 0x64=100, which means firmware version 1.00.
328 328  
329 -For example 0x00 64 : This device is CPN01 with firmware version 1.0.0.
391 +For example 0x00 64 : This device is NDS03A 1 with firmware version 1.0.0.
330 330  
331 331  
332 -=== **2.4.3  Battery Info** ===
394 +=== 2.4.3  Battery Info ===
333 333  
334 -Check the battery voltage for CPN01.
335 335  
397 +Check the battery voltage for NDS03A.
398 +
336 336  Ex1: 0x0B45 = 2885mV
337 337  
338 338  Ex2: 0x0B49 = 2889mV
339 339  
340 340  
341 -=== **2.4.4  Signal Strength** ===
404 +=== 2.4.4  Signal Strength ===
342 342  
406 +
343 343  NB-IoT Network signal Strength.
344 344  
345 345  **Ex1: 0x1d = 29**
... ... @@ -355,62 +355,45 @@
355 355  **99**    Not known or not detectable
356 356  
357 357  
358 -=== **2.4.5 Calculate Flag** ===
422 +=== 2.4.5  Disalarm: (default: 0) ===
359 359  
360 -The calculate flag is a user defined field, IoT server can use this filed to handle different meters with different pulse factors. For example, if there are 100 water meters, meter 1~~50 are 1 liter/pulse and meter 51 ~~ 100 has 1.5 liter/pulse.
361 361  
362 -User can set calculate flag to 1 for meter 1~~50 and 2 for meter 51 ~~ 100, So IoT Server can use this field for calculation.
425 +(% style="color:blue" %)**If Disalarm = 1**(%%), NDS03A will only send uplink at every TDC periodically. This is normally use for pulse meter application, in this application, there are many open/close event, and platform only care about the total number of pulse.
363 363  
364 -Default value: 0. 
427 +(% style="color:blue" %)**If Disalarm = 0**(%%), NDS03A will send uplink at every TDC periodically and send data on each open/close event. This is useful for the application user need to monitor the open/close event in real-time.
365 365  
366 -Range (6 bits): (b)000000 ~~ (b) 111111
429 + (% style="color:red" %)**Note:**(%%) When Disalarm=0, a high frequently open/close event will cause lots of uplink and drain battery very fast.
367 367  
368 368  
369 -=== **2.4.6  Alarm** ===
432 +=== 2.4.6  Keep Status & Keep Time ===
370 370  
371 -See [[Alarm Base on Timeout>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/CPL01%20LoRaWAN%20Outdoor%20PulseContact%20%20Sensor%20Manual/#H3.5AlarmBaseonTimeout]]
372 372  
435 +Shows the configure value of Alarm Base on Timeout Feature
373 373  
374 -=== **2.4.7 Contact Status** ===
375 375  
376 -0: Open
438 +=== 2.4.7  Timestamp ===
377 377  
378 -1: Close
379 379  
441 +Timestamp : 0x6315537b =1662342011
380 380  
381 -=== **2.4.8 Total pulse** ===
382 382  
383 -Total pulse/counting based on dry [[contact trigger event>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/CPL01%20LoRaWAN%20Outdoor%20PulseContact%20%20Sensor%20Manual/#H2.3.2SensorConfiguration2CFPORT3D4]]
444 +=== 2.4.8  Switch Dual Channel Mode ===
384 384  
385 -Range (3 Bytes) : 0x000000 ~~ 0xFFFFFF . Max: 16777215
386 386  
447 +NDS03A can connect two door sensors. Another door sensor can be connected to PB15 pin. Both channels support alarm function.
387 387  
388 -=== **2.4.9 The last open duration** ===
389 389  
390 -Dry Contact last open duration.
450 +== 2.5  Downlink Payload ==
391 391  
392 -Unit: min.
393 393  
394 -[[image:image-20221021111346-17.png||height="146" width="770"]]
453 +By default, NDS03A prints the downlink payload to console port.
395 395  
396 -
397 -=== **2.4.10  Timestamp** ===
398 -
399 -Timestamp : 0x6315537b =1662342011
400 -
401 -Convert Unix timestamp to time 2022-9-5 9:40:11.
402 -
403 -**~ **
404 -
405 -== **2.5  Downlink Payload** ==
406 -
407 -By default, CPN01 prints the downlink payload to console port.
408 -
409 409  [[image:image-20221021111414-18.png]] ​
410 410  
457 +
411 411  **Examples:**
412 412  
413 -* **Set TDC**
460 +* (% style="color:#037691" %)**Set TDC**
414 414  
415 415  If the payload=0100003C, it means set the END Node's TDC to 0x00003C=60(S), while type code is 01.
416 416  
... ... @@ -418,172 +418,221 @@
418 418  
419 419  Payload:    01 00 00 3C    TDC=60S
420 420  
421 -* **Reset**
468 +* (% style="color:#037691" %)**Reset**
422 422  
423 -If payload = 0x04FF, it will reset the NSE01
470 +If payload = 0x04FF, it will reset the NDS03A
424 424  
425 -* **INTMOD**
472 +* (% style="color:#037691" %)**INTMOD**
426 426  
427 427  Downlink Payload: 06000003, Set AT+INTMOD=3
428 428  
429 -== **2.6  ​LED Indicator** ==
430 430  
431 -The CPN01 has an internal LED which is to show the status of different states.
477 +== 2.6  ​LED Indicator ==
432 432  
479 +
480 +The NDS03A has an internal LED which is to show the status of different states.
481 +
433 433  * When the device starts normally, the LED will light up for 1 second.
434 -* After CPN01 join NB-IoT network. The LED will be ON for 3 seconds.
483 +* After NDS03A join NB-IoT network. The LED will be ON for 3 seconds.
435 435  * For each uplink probe, LED will be on for 500ms.
436 436  
437 -== **2.7  Alarm Base on Timeout** ==
486 +== 2.7  Alarm Base on Timeout ==
438 438  
439 -CPN01 can monitor the timeout for a status change, this feature can be used to monitor some events such as door opening too long etc. Related Parameters are:
440 440  
489 +NDS03A can monitor the timeout for a status change, this feature can be used to monitor some events such as door opening too long etc. Related Parameters are:
441 441  
442 -**~1. Keep Status: Status to be monitor**
443 443  
492 +(% style="color:blue" %)**1. Keep Status: Status to be monitor**
493 +
444 444  Keep Status = 1: Monitor Close to Open event
445 445  
446 446  Keep Status = 0: Monitor Open to Close event
447 447  
448 448  
449 -**2. Keep Time: Timeout to send an Alarm**
499 +(% style="color:blue" %)**2. Keep Time: Timeout to send an Alarm**
450 450  
451 451  Range 0 ~~ 65535(0xFFFF) seconds.
452 452  
453 453  If keep time = 0, Disable Alarm Base on Timeout feature.
454 454  
455 -If keep time > 0, device will monitor the keep status event and send an alarm when status doesn’t change after timeout.
505 +If keep time > 0, device will monitor the keep status event and send an alarm when status doesn't change after timeout.
456 456  
457 457  
458 -**AT Command** to configure:
508 +(% style="color:blue" %)**AT Command to configure:**
459 459  
460 -**AT+TTRIG=1,30**  ~-~-> When the **Keep Status** change from connected to disconnect, and device remains in disconnect status for more than 30 seconds. CPN01 will send an uplink packet, the [[Alarm bit>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/CPL01%20LoRaWAN%20Outdoor%20PulseContact%20%20Sensor%20Manual/#H2.3.3Real-TimeOpen2FCloseStatus2CUplinkFPORT3D2]] (the second bit of 1^^st^^ byte of payload) on this uplink packet is set to 1.
510 +(% style="color:blue" %)**PB14 PIN:**
461 461  
462 -**AT+TTRIG=0,0 ** ~-~-> Default Value, disable timeout Alarm.
512 +(% style="color:#037691" %)**AT+TTRIG=1,30** (%%) **~-~->**  When the **Keep Status** change from connected to disconnect, and device remains in disconnect status for more than 30 seconds. NDS03A will send an uplink packet, the [[Alarm bit>>url:http://wiki.dragino.com/xwiki/bin/view/Main/User%20Manual%20for%20LoRaWAN%20End%20Nodes/CPL01%20LoRaWAN%20Outdoor%20PulseContact%20%20Sensor%20Manual/#H2.3.3Real-TimeOpen2FCloseStatus2CUplinkFPORT3D2]] (the second bit of 1^^st^^ byte of payload) on this uplink packet is set to 1.
463 463  
514 +(% style="color:#037691" %)**AT+TTRIG=0,0 ** (%%) **~-~->** Default Value, disable timeout Alarm.
464 464  
465 -== **2.8 Set debug mode** ==
466 466  
467 -Feature: Enable or Disable debug mode
517 +(% style="color:blue" %)**PB15 PIN:**
468 468  
519 +(% style="color:#037691" %)**AT+TTRIG2=1,30**
469 469  
470 -**AT Command: AT+DEBUG**
521 +(% style="color:#037691" %)**AT+TTRIG2=0,0 **
471 471  
523 +
524 +== 2.8  Set debug mode ==
525 +
526 +
527 +Feature: Enable or Disable debug mode
528 +
529 +(% style="color:blue" %)**AT Command: AT+DEBUG**
530 +
472 472  [[image:image-20221021111629-21.png]]
473 473  
474 -== **2.9 Clear Flash Record** ==
475 475  
534 +
535 +== 2.9  Clear Flash Record ==
536 +
537 +
476 476  Feature: Clear flash storage for data log feature.
477 477  
478 -**AT Command: AT+CLRDTA**
540 +(% style="color:blue" %)**AT Command: AT+CLRDTA**
479 479  
480 480  [[image:image-20221021111527-19.png]]
481 481  
482 -== ** 2.10 Set trigger mode** ==
483 483  
484 -➢ AT Command: **AT+TTRMOD**
545 +== 2.10  Count Mod ==
485 485  
486 -Feature: Set the trigger interrupt mode.
487 487  
488 -[[image:image-20221021111552-20.png]]
548 +(% style="color:blue" %)**AT Command: AT+COUNTMOD**
489 489  
490 -== **2.11 Set the calculate flag** ==
550 +[[image:image-20221118092935-1.png]]
491 491  
492 -Feature: Set the calculate flag
493 493  
494 -**AT Command: AT+CALCFLAG**
553 +== 2.11  Interrupt Pin Channel Mod ==
495 495  
496 -[[image:image-20221021111711-22.png]]
497 497  
498 -== **2.12 Set count number** ==
556 +(% style="color:blue" %)**AT Command: AT+TTRCHANNEL**
499 499  
500 -Feature: Manually set the count number
558 +[[image:image-20221118093144-2.png]]
501 501  
502 -**AT Command: AT+SETCNT**
503 503  
504 -[[image:image-20221021111748-24.png]]
561 +== 2.12 TTRIG1/2 timeout status alarm ==
505 505  
506 -== **2.13 Set the number of data to be uploaded and the recording time** ==
507 507  
508 -➢ AT Command:
564 +It needs to be used with AT+TTRIG1 or AT+TTRIG2. When TTRIG1 or TTRIG2 times out and causes an alarm, and the status does not change subsequently, an alarm packet will be sent at the alarm interval.
509 509  
510 -AT+TR=900  ~/~/The unit is seconds, and the default is to record data once every 900 seconds.( The minimum can be set to 180 seconds)
566 +(% style="color:blue" %)**AT Command: AT+TTRALARM**
511 511  
568 +[[image:image-20221118093512-3.png]]
512 512  
513 -AT+NOUD=8  ~/~/The device uploads 8 sets of recorded data by default. Up to 32 sets of record data can be uploaded.
514 514  
515 -== **2.14 Read or Clear cached data** ==
571 +== 2.13  Select counting mode ==
516 516  
517 -➢ AT Command:
518 518  
519 -AT+CDP    ~/~/ Read cached data
574 +(% style="color:blue" %)**AT Command: AT+TTRMODx=a,b**
520 520  
521 -[[image:image-20221021111810-25.png||height="364" width="797"]]
576 +When (% style="color:red" %)**a=0**(%%), the door is opened to count, and when (% style="color:red" %)**a=1**(%%),the closed door is counted.
522 522  
578 +When (% style="color:red" %)**b=0**(%%), it is the last door open duration, and when (% style="color:red" %)**b=1**(%%),the last door close duration.
523 523  
524 -AT+CDP=0    ~/~/ Clear cached data ​
580 +[[image:image-20221118093658-4.png]]
525 525  
526 -== **2.15  ​Firmware Change Log** ==
527 527  
528 -Download URL & Firmware Change log: [[https:~~/~~/www.dropbox.com/sh/1zmcakvbkf24f8x/AACmq2dZ3iRB9F1nVWeEB9Moa?dl=0>>url:https://www.dropbox.com/sh/1zmcakvbkf24f8x/AACmq2dZ3iRB9F1nVWeEB9Moa?dl=0]]
583 +== 2.14  Set the number of data to be uploaded and the recording time ==
529 529  
530 -Upgrade Instruction: [[Upgrade Firmware>>path:#H5.1200BHowtoUpgradeFirmware]]
531 531  
532 -== **2.16  ​Battery Analysis** ==
586 +(% style="color:blue" %)**AT Command:**
533 533  
534 -=== **2.16.1  ​Battery Type** ===
588 +(% style="color:#037691" %)**AT+TR=900**(%%)  ~/~/  The unit is seconds, and the default is to record data once every 900 seconds.( The minimum can be set to 180 seconds)
535 535  
536 -The CPN01 battery is a combination of an 8500mAh Li/SOCI2 Battery and a Super Capacitor. The battery is non-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
590 +(% style="color:#037691" %)**AT+NOUD=8**(%%)** ** ~/~/  The device uploads 0 sets of recorded data by default. Up to 32 sets of record data can be uploaded.
537 537  
592 +
593 +== 2.15  Read or Clear cached data ==
594 +
595 +
596 +(% style="color:blue" %)**AT Command:**
597 +
598 +(% style="color:#037691" %)**AT+CDP**  (%%) ~/~/ Read cached data
599 +
600 +(% style="color:#037691" %)**AT+CDP=0**  (%%) ~/~/ Clear cached data ​
601 +
602 +[[image:image-20221118094227-5.png]]
603 +
604 +
605 +== 2.16  ​Firmware Change Log ==
606 +
607 +
608 +Download URL & Firmware Change log: [[https:~~/~~/www.dropbox.com/sh/hacq385w6qgnonr/AAC3D79GFGF1JdZUIzNegn2Ha?dl=0>>https://www.dropbox.com/sh/hacq385w6qgnonr/AAC3D79GFGF1JdZUIzNegn2Ha?dl=0]]
609 +
610 +Upgrade Instruction: [[Upgrade Firmware>>||anchor="H5.1200BHowtoUpgradeFirmware"]]
611 +
612 +
613 +== 2.17  ​Battery Analysis ==
614 +
615 +=== 2.17.1  ​Battery Type ===
616 +
617 +
618 +The NDS03A battery is a combination of an 8500mAh Li/SOCI2 Battery and a Super Capacitor. The battery is non-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
619 +
538 538  The battery is designed to last for several years depends on the actual use environment and update interval. 
539 539  
540 540  The battery-related documents as below:
541 541  
542 542  * [[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
625 +
543 543  * [[Lithium-Thionyl Chloride Battery datasheet>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
627 +
544 544  * [[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
545 545  
546 546  [[image:image-20221021111911-26.png]] ​
547 547  
548 -=== **2.16.2  Power consumption Analyze** ===
549 549  
633 +=== 2.17.2  Power consumption Analyze ===
634 +
635 +
550 550  Dragino battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
551 551  
552 552  Instruction to use as below:
553 553  
554 -**Step 1:  **Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/]]
640 +(% style="color:blue" %)**Step 1:  **(%%)Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/]]
555 555  
556 -**Step 2: ** Open it and choose
642 +(% style="color:blue" %)**Step 2: **(%%) Open it and choose
557 557  
558 558  * Product Model
645 +
559 559  * Uplink Interval
647 +
560 560  * Working Mode
561 561  
562 562  And the Life expectation in difference case will be shown on the right.
563 563  
564 -[[image:image-20221021111923-27.png||height="253" width="783"]] ​
652 +[[image:1666596205057-567.png]] ​
565 565  
566 -=== **2.16.3  ​Battery Note** ===
567 567  
655 +=== 2.17.3  ​Battery Note ===
656 +
657 +
568 568  The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
569 569  
570 -=== **2.16.4  Replace the battery** ===
571 571  
572 -The default battery pack of CPN01 includes a ER26500 plus super capacitor. If user can't find this pack locally, they can find ER26500 or equivalence without the SPC1520 capacitor, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes).
661 +=== 2.17.4  Replace the battery ===
573 573  
574 574  
575 -= **3. ​ Access NB-IoT Module** =
664 +The default battery pack of NDS03A includes a ER26500 plus super capacitor. If user can't find this pack locally, they can find ER26500 or equivalence without the SPC1520 capacitor, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes).
576 576  
666 +
667 += 3. ​ Access NB-IoT Module =
668 +
669 +
577 577  Users can directly access the AT command set of the NB-IoT module.
578 578  
579 579  The AT Command set can refer the BC35-G NB-IoT Module AT Command: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/]] 
580 580  
581 -[[image:image-20221021112006-28.png]] ​
582 582  
583 -= **4.  Using the AT Commands** =
675 +[[image:image-20221118094449-6.png]] ​
584 584  
585 -== **4.1  Access AT Commands** ==
586 586  
678 += 4.  Using the AT Commands =
679 +
680 +== 4.1  Access AT Commands ==
681 +
682 +
587 587  See this link for detail:  [[https:~~/~~/www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0>>url:https://www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0]]
588 588  
589 589  AT+<CMD>?  : Help on <CMD>
... ... @@ -594,8 +594,9 @@
594 594  
595 595  AT+<CMD>=?  : Get the value
596 596  
597 -**General Commands**      
598 598  
694 +(% style="color:blue" %)**General Commands**      
695 +
599 599  AT  : Attention       
600 600  
601 601  AT?  : Short Help     
... ... @@ -618,35 +618,41 @@
618 618  
619 619  AT+SERVADDR  : Server Address
620 620  
621 -AT+TR      : Get or Set record time"
718 +AT+TR      :  Get or Set record time
622 622  
623 -
624 624  AT+NOUD      : Get or Set the number of data to be uploaded
625 625  
722 +AT+CDP     :  Read or Clear cached data
626 626  
627 -AT+CDP     : Read or Clear cached data
724 +AT+ DEBUG   : Enable or Disable debug mode
628 628  
726 +AT+ TTRIG1   : Get or Set PB14 PIN Alarm Base on Timeout
629 629  
630 -AT+ DEBUG   : Enable or Disable debug mode
728 +AT+ TTRIG2   : Get or Set PB15 PIN Alarm Base on Timeout
631 631  
632 -AT+ TTRIG   : Get or Set Alarm Base on Timeout
730 +AT+COUNTMOD  :  Get or Set the count mode
633 633  
634 -AT+ TTRMOD   : Get or Set the trigger interrupt mode(0:falling,1:rising)
732 +AT+TTRCHANNEL  : Get or Set the number of interrupt channels
635 635  
636 -AT+ CALCFLAG   : Get or Set the calculate flag
734 +AT+TTRALARM : Get or Set TTRIG1 of Alarm interval (unit: minute)
637 637  
638 -AT+ CLRC   : Clear current door open count
736 +AT+DISALARM  : Enable/Disable Alarm for door open/close or water leak event
639 639  
640 -**COAP Management**      
738 +AT+ CLRC   :  Clear current door open count
641 641  
740 +
741 +(% style="color:blue" %)**COAP Management**      
742 +
642 642  AT+URI            : Resource parameters
643 643  
644 -**UDP Management**
645 645  
746 +(% style="color:blue" %)**UDP Management**
747 +
646 646  AT+CFM          : Upload confirmation mode (only valid for UDP)
647 647  
648 -**MQTT Management**
649 649  
751 +(% style="color:blue" %)**MQTT Management**
752 +
650 650  AT+CLIENT               : Get or Set MQTT client
651 651  
652 652  AT+UNAME  : Get or Set MQTT Username
... ... @@ -657,86 +657,58 @@
657 657  
658 658  AT+SUBTOPIC  : Get or Set MQTT subscription topic
659 659  
660 -**Information**          
661 661  
764 +(% style="color:blue" %)**Information**          
765 +
662 662  AT+FDR  : Factory Data Reset
663 663  
664 664  AT+PWORD  : Serial Access Password
665 665  
666 -= **​5.  FAQ** =
667 667  
668 -== **5.1 ​ How to Upgrade Firmware** ==
771 += ​5.  FAQ =
669 669  
773 +== 5.1 ​ How to Upgrade Firmware ==
774 +
775 +
670 670  User can upgrade the firmware for 1) bug fix, 2) new feature release.
671 671  
672 672  Please see this link for how to upgrade:  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList]]
673 673  
674 -**Notice, **CPN01 **and **CPL01 **share the same mother board. They use the same connection and method to update.**
780 +(% style="color:red" %)**Notice: **(% style="color:blue" %)**NDS03A** (%%)**and (% style="color:blue" %)LDS03A(%%)**(% style="color:blue" %) (%%)**share the same mother board. They use the same connection and method to update.**
675 675  
676 676  
677 -= **6.  Trouble Shooting** =
783 += 6.  Trouble Shooting =
678 678  
679 -== **6.1  ​Connection problem when uploading firmware** ==
785 +== 6.1  ​Connection problem when uploading firmware ==
680 680  
681 -**Please see: **[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting]]
682 682  
788 +(% style="color:blue" %)**Please see: **[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting]]
683 683  
684 -== **6.2  AT Command input doesn't work** ==
685 685  
686 -In the case if user can see the console output but can't type input to the device. Please check if you already include the **ENTER** while sending out the command. Some serial tool doesn't send **ENTER** while press the send key, user need to add ENTER in their string.
791 +== 6.2  AT Command input doesn't work ==
687 687  
688 688  
689 -= **7. ​ Order Info** =
794 +In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER** (%%)while press the send key, user need to add ENTER in their string.
690 690  
691 -Part Number**:** CPN01
692 692  
797 += 7. ​ Order Info =
693 693  
694 -= **8.  Packing Info** =
695 695  
696 -**Package Includes**:
800 +Part Number**:** NDS03A
697 697  
698 -* CPN01 Open/Close Sensor x 1
699 -* External antenna x 1
700 700  
701 -**Dimension and weight**:
803 += 8.  Packing Info =
702 702  
703 -* Size: 195 x 125 x 55 mm
704 -* Weight:   420g
705 705  
706 -= **9.  Support** =
806 +(% style="color:blue" %)**Package Includes**:
707 707  
708 -* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
709 -* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]
808 +* NDS03A Open/Close Door Sensor x 1
710 710  
711 -​
810 += 9.  Support =
712 712  
713 713  
813 +* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
714 714  
815 +* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]
715 715  
716 -
717 -
718 -
719 -
720 -
721 -
722 -
723 -
724 -
725 -
726 -
727 -
728 -
729 -
730 -
731 -
732 -
733 -
734 -
735 -
736 -
737 -
738 -
739 -
740 -
741 -
742 -
817 +​
1666596205057-567.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +179.8 KB
Content
1670404362039-351.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +492.6 KB
Content
1670405841875-916.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +76.1 KB
Content
1670405928926-116.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +76.7 KB
Content
1670406036256-101.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +181.0 KB
Content
1670406261143-723.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +77.9 KB
Content
LMDS200_10.jpg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +39.9 KB
Content
image-20221117105556-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +133.3 KB
Content
image-20221117114459-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +14.9 KB
Content
image-20221117114842-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +964.1 KB
Content
image-20221117114937-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +79.1 KB
Content
image-20221117114949-5.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +33.4 KB
Content
image-20221117115010-6.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +40.4 KB
Content
image-20221117142300-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +147.8 KB
Content
image-20221117145932-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +51.9 KB
Content
image-20221117150312-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +8.7 KB
Content
image-20221118092935-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +13.1 KB
Content
image-20221118093144-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +11.7 KB
Content
image-20221118093512-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +9.5 KB
Content
image-20221118093658-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +12.7 KB
Content
image-20221118094227-5.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +29.2 KB
Content
image-20221118094449-6.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +76.5 KB
Content
image-20221118103445-7.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +20.4 KB
Content
image-20221118103453-8.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +46.2 KB
Content
image-20221118103547-9.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +43.5 KB
Content
image-20221207170748-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +26.1 KB
Content
image-20221207170748-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +29.9 KB
Content
image-20221207173200-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +76.7 KB
Content
image-20221207173300-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +77.0 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0