Changes for page NLMS01-NB-IoT Leaf Moisture Sensor User Manual

Last modified by Mengting Qiu on 2024/04/02 16:54

From version < 38.17 >

edited by Xiaoling
on 2023/05/24 08:47

To version < 33.2 >

edited by Xiaoling
on 2022/09/13 09:14

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)
Attachments (0 modified, 0 added, 1 removed)
- image-20221009001002-1.png

Details

Page properties

Content

@@ -9,24 +9,20 @@
  = 1.  Introduction =
++
  == 1.1  What is NLMS01 Leaf Moisture Sensor ==
--(((
  The Dragino NLMS01 is a (% style="color:blue" %)**NB-IOT Leaf Moisture Sensor**(%%) for IoT of Agriculture. It is designed to measure the leaf moisture and temperature, so to send to the platform to analyze the leaf status such as : watering, moisturizing, dew, frozen. The probe is IP67 waterproof.
  NLMS01 detects leaf's(% style="color:blue" %)** moisture and temperature use FDR method**(%%), it senses the dielectric constant cause by liquid over the leaf surface, and cover the value to leaf moisture. The probe is design in a leaf shape to best simulate the real leaf characterizes. The probe has as density as 15 leaf vein lines per centimeter which make it can senses small drop and more accuracy.
  NarrowBand-Internet of Things (NB-IoT) is a standards-based low power wide area (LPWA) technology developed to enable a wide range of new IoT devices and services. NB-IoT significantly improves the power consumption of user devices, system capacity and spectrum efficiency, especially in deep coverage.
++\\NLMS01 supports different uplink methods include (% style="color:blue" %)**TCP,MQTT,UDP and CoAP  **(%%)for different application requirement.
++\\NLMS01 is powered by  (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), It is designed for long term use up to 5 years. (Actually Battery life depends on the use environment, update period & uplink method).
++\\To use NLMS01, user needs to check if there is NB-IoT coverage in local area and with the bands NLMS01 supports. If the local operate support it, user needs to get a (% style="color:blue" %)**NB-IoT SIM card**(%%) from local operator and install NLMS01 to get NB-IoT network connection.
--NLMS01 supports different uplink methods include (% style="color:blue" %)**TCP,MQTT,UDP and CoAP  **(%%)for different application requirement.
--NLMS01 is powered by  (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), It is designed for long term use up to 5 years. (Actually Battery life depends on the use environment, update period & uplink method).
--
--To use NLMS01, user needs to check if there is NB-IoT coverage in local area and with the bands NLMS01 supports. If the local operate support it, user needs to get a (% style="color:blue" %)**NB-IoT SIM card**(%%) from local operator and install NLMS01 to get NB-IoT network connection.
--)))
--
--
  [[image:image-20220907171221-2.png]]
@@ -33,6 +33,7 @@
   [[image:image-20220907171221-3.png]]
++
  == 1.2  Features ==
@@ -53,6 +53,7 @@
  (((
++
  )))
@@ -66,14 +66,13 @@
  (% style="color:#037691" %)**NB-IoT Spec:**
--* B1 @H-FDD: 2100MHz
--* B3 @H-FDD: 1800MHz
--* B8 @H-FDD: 900MHz
--* B5 @H-FDD: 850MHz
--* B20 @H-FDD: 800MHz
--* B28 @H-FDD: 700MHz
++* - B1 @H-FDD: 2100MHz
++* - B3 @H-FDD: 1800MHz
++* - B8 @H-FDD: 900MHz
++* - B5 @H-FDD: 850MHz
++* - B20 @H-FDD: 800MHz
++* - B28 @H-FDD: 700MHz
--
  == 1.4  Probe Specification ==
@@ -93,13 +93,11 @@
  * IP67 Protection
  * Length: 3.5 meters
--
  == 1.5  Applications ==
  * Smart Agriculture
--
  == 1.6  Pin mapping and power on ==
@@ -107,8 +107,10 @@
  **~ **
++
  = 2.  Use NLMS01 to communicate with IoT Server =
++
  == 2.1  How it works ==
@@ -120,8 +120,10 @@
  [[image:image-20220907171221-5.png]]
++
  == 2.2  Configure the NLMS01 ==
++
  === 2.2.1  Test Requirement ===
@@ -137,6 +137,7 @@
  [[image:image-20220907171221-6.png]]
++
  === 2.2.2  Insert SIM card ===
@@ -148,6 +148,7 @@
  [[image:image-20220907171221-7.png]]
++
  === 2.2.3  Connect USB – TTL to NLMS01 to configure it ===
@@ -179,6 +179,7 @@
  (% style="color:red" %)**Note: the valid AT Commands can be found at:  **(%%)[[**https:~~/~~/www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0**>>url:https://www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0]]
++
  === 2.2.4  Use CoAP protocol to uplink data ===
@@ -191,6 +191,8 @@
  * (% style="color:#037691" %)**AT+SERVADDR=120.24.4.116,5683   ** (%%)  ~/~/   to set CoAP server address and port
  * (% style="color:#037691" %)**AT+URI=5,11,"mqtt",11,"coap",12,"0",15,"c=text1",23,"0" **   (%%)    ~/~/   Set COAP resource path
++
++
  For parameter description, please refer to AT command set
  [[image:image-20220907171221-9.png]]
@@ -201,6 +201,7 @@
  [[image:image-20220907171221-10.png]]
++
  === 2.2.5  Use UDP protocol to uplink data(Default protocol) ===
@@ -207,9 +207,11 @@
  This feature is supported since firmware version v1.0.1
  * (% style="color:#037691" %)**AT+PRO=2   **     (%%)   ~/~/  Set to use UDP protocol to uplink
--* (% style="color:#037691" %)**AT+SERVADDR=120.24.4.116,5601     ** (%%)  ~/~/  to set UDP server address and port
++* (% style="color:#037691" %)**AT+SERVADDR=120.24.4.116,5601     ** (%%)  ~/~/  to set UDP server address and port
  * (% style="color:#037691" %)**AT+CFM=1       ** (%%)   ~/~/  If the server does not respond, this command is unnecessary
++
++
   [[image:image-20220907171221-11.png]]
@@ -217,6 +217,7 @@
++
  === 2.2.6  Use MQTT protocol to uplink data ===
@@ -230,6 +230,8 @@
  * (% style="color:#037691" %)**AT+PUBTOPIC=PUB                    **            (%%) ~/~/  Set the sending topic of MQTT
  * (% style="color:#037691" %)**AT+SUBTOPIC=SUB          **     (%%)                  ~/~/  Set the subscription topic of MQTT
++
++
   [[image:image-20220907171221-13.png]]
@@ -241,6 +241,7 @@
  MQTT protocol has a much higher power consumption compare vs UDP / CoAP protocol. Please check the power analyze document and adjust the uplink period to a suitable interval.
++
  === 2.2.7  Use TCP protocol to uplink data ===
@@ -249,6 +249,8 @@
  * (% style="color:#037691" %)**AT+PRO=4   **             (%%)                              ~/~/  Set to use TCP protocol to uplink
  * (% style="color:#037691" %)**AT+SERVADDR=120.24.4.116,5600   ** (%%) ~/~/   to set TCP server address and port
++
++
   [[image:image-20220907171221-15.png]]
@@ -265,9 +265,12 @@
  * (% style="color:#037691" %)**AT+TDC=7200      ** (%%) ~/~/ Set Update Interval to 7200s (2 hour)
++
++
  (% style="color:red" %)**NOTE: By default, the device will send an uplink message every 2 hour. Each Uplink Include 8 set of records in this 2 hour (15 minute interval / record).**
++
  == 2.3  Uplink Payload ==
@@ -276,10 +276,11 @@
  Each time the device uploads a data package, 8 sets of recorded data will be attached. Up to 32 sets of recorded data can be uploaded.
--(% border="1" cellspacing="5" style="background-color:#f2f2f2; width:520px" %)
--|(% style="width:50px;background-color:#D9E2F3;color:#0070C0" %)**Size(bytes)**|(% style="width:40px;background-color:#D9E2F3;color:#0070C0" %)**8**|(% style="width:20px;background-color:#D9E2F3;color:#0070C0" %)**2**|(% style="width:20px;background-color:#D9E2F3;color:#0070C0" %)**2**|(% style="width:60px;background-color:#D9E2F3;color:#0070C0" %)**1**|(% style="width:20px;background-color:#D9E2F3;color:#0070C0" %)**1**|(% style="width:40px;background-color:#D9E2F3;color:#0070C0" %)**1**|(% style="width:40px;background-color:#D9E2F3;color:#0070C0" %)**2**|(% style="width:50px;background-color:#D9E2F3;color:#0070C0" %)**2**|(% style="width:50px;background-color:#D9E2F3;color:#0070C0" %)**4**|(% style="width:50px;background-color:#D9E2F3;color:#0070C0" %)**2**|(% style="width:40px;background-color:#D9E2F3;color:#0070C0" %)**2**|(% style="width:40px;background-color:#D9E2F3;color:#0070C0" %)**4**
++(% border="1" style="background-color:#ffffcc; color:green; width:1251px" %)
++|(% style="width:96px" %)**Size(bytes)**|(% style="width:82px" %)**8**|(% style="width:42px" %)**2**|(% style="width:48px" %)**2**|(% style="width:124px" %)1|(% style="width:58px" %)1|(% style="width:82px" %)1|(% style="width:113px" %)2|(% style="width:134px" %)2|(% style="width:100px" %)4|(% style="width:137px" %)2|(% style="width:110px" %)2|(% style="width:122px" %)4
  |(% style="width:96px" %)**Value**|(% style="width:82px" %)Device ID|(% style="width:42px" %)Ver|(% style="width:48px" %)BAT|(% style="width:124px" %)Signal Strength|(% style="width:58px" %)MOD|(% style="width:82px" %)Interrupt|(% style="width:113px" %)Leaf moisture|(% style="width:134px" %)Leaf Temperature|(% style="width:100px" %)Time stamp|(% style="width:137px" %)Leaf Temperature|(% style="width:110px" %)Leaf moisture|(% style="width:122px" %)Time stamp  .....
++
  If we use the MQTT client to subscribe to this MQTT topic, we can see the following information when the NLMS01 uplink data.
@@ -288,60 +288,46 @@
  The payload is ASCII string, representative same HEX:
--**0x (% style="color:red" %)__f868411056754138__  (% style="color:blue" %)__0064 __ (% style="color:green" %)__0c78__  (% style="color:#00b0f0" %)__17__  (% style="color:#7030a0" %)__01__  (% style="color:#d60093" %)__00__  (% style="color:#a14d07" %)__0225 __ (% style="color:#0020b0" %) __010b__  (% style="color:#420042" %)__6315537b__  (% style="color:#663300" %)//__010b0226631550fb__  __010e022663154d77  01110225631549f1  011502246315466b  01190223631542e5  011d022163153f62  011e022163153bde 011e022163153859__//(%%)**
++0x(% style="color:red" %)f868411056754138(% style="color:blue" %)0064(% style="color:green" %)0c78(% style="color:red" %)17(% style="color:blue" %)01(% style="color:green" %)00(% style="color:blue" %)**0225010b6315537b**010b0226631550fb**010e022663154d77**01110225631549f1**011502246315466b**01190223631542e5**011d022163153f62**011e022163153bde**011e022163153859**(%%)** **where:
--where:
++* (% style="color:red" %)Device ID: 0xf868411056754138 = f868411056754138
++* (% style="color:blue" %)Version: 0x0064=100=1.0.0
++* (% style="color:green" %)BAT: 0x0c78 = 3192 mV = 3.192V
++* (% style="color:red" %)Singal: 0x17 = 23
++* (% style="color:blue" %)Mod: 0x01 = 1
++* (% style="color:green" %)Interrupt: 0x00= 0
++* Leaf moisture: 0x0225= 549 = 54.9%
++* Leaf Temperature:0x010B =267=26.7 °C
++* Time stamp : 0x6315537b =1662342011 ([[Unix Epoch Time>>https://www.epochconverter.com/]])
++* Leaf Temperature, Leaf moisture,Time stamp : 010b0226631550fb
++* (% style="color:blue" %)8 sets of recorded data: Leaf Temperature, Leaf moisture,Time stamp : 010e022663154d77,.......
--* (% style="color:#037691" %)**Device ID:**(%%) 0xf868411056754138 = f868411056754138
--* (% style="color:#037691" %)**Version:**(%%) 0x0064=100=1.0.0
--* (% style="color:#037691" %)**BAT:**       (%%)0x0c78 = 3192 mV = 3.192V
--* (% style="color:#037691" %)**Singal:**(%%)   0x17 = 23
--* (% style="color:#037691" %)**Mod:**(%%)  0x01 = 1
--
--* (% style="color:#037691" %)**Interrupt:**(%%) 0x00= 0
--
--* (% style="color:#037691" %)**Leaf moisture:**(%%) 0x0225= 549 = 54.9%
--
--* (% style="color:#037691" %)**Leaf Temperature: **(%%)0x010B =267=26.7 °C
--
--* (% style="color:#037691" %)**Time stamp :**   (%%)0x6315537b =1662342011 ([[Unix Epoch Time>>https://www.epochconverter.com/]])
--
--* (% style="color:#037691" %)**Leaf Temperature, Leaf moisture,Time stamp :  **(%%)010b0226631550fb
--
--* (% style="color:#037691" %)**8 sets of recorded data: **(%%)Leaf Temperature, Leaf moisture,Time stamp : 010e022663154d77,.......
--
  == 2.4  Payload Explanation and Sensor Interface ==
  === 2.4.1  Device ID ===
--
  By default, the Device ID equal to the last 15 bits of IMEI.
--User can use (% style="color:#037691" %)**AT+DEUI**(%%) to set Device ID
++User can use **AT+DEUI** to set Device ID
++**Example:**
--(% style="color:blue" %)**Example**:
--
  AT+DEUI=868411056754138
  The Device ID is stored in a none-erase area, Upgrade the firmware or run AT+FDR won't erase Device ID.
--
  === 2.4.2  Version Info ===
--
  Specify the software version: 0x64=100, means firmware version 1.00.
  For example: 0x00 64 : this device is NLMS01 with firmware version 1.0.0.
--
  === 2.4.3  Battery Info ===
--
  Check the battery voltage for NLMS01.
  Ex1: 0x0B45 = 2885mV
@@ -348,15 +348,12 @@
  Ex2: 0x0B49 = 2889mV
--
  === 2.4.4  Signal Strength ===
--
  NB-IoT Network signal Strength.
++**Ex1: 0x1d = 29**
--(% style="color:blue" %)**Ex1: 0x1d = 29**
--
  **0**        -113dBm or less
  **1**        -111dBm
@@ -367,45 +367,37 @@
  **99**      Not known or not detectable
--
  === 2.4.5  Leaf moisture ===
++Get the moisture of the **Leaf**. The value range of the register is 300-1000(Decimal), divide this value by 100 to get the percentage of moisture in the **Leaf**.
--Get the moisture of the (% style="color:#037691" %)**Leaf**(%%). The value range of the register is 300-1000(Decimal), divide this value by 100 to get the percentage of moisture in the Leaf.
++For example, if the data you get from the register is **__0x05 0xDC__**, the moisture content in the **Leaf** is
--For example, if the data you get from the register is (% style="color:#037691" %)**__0x05 0xDC__**(%%), the moisture content in the (% style="color:#037691" %)**Leaf**(%%) is
++**0229(H) = 549(D) /100 = 54.9.**
--(% style="color:blue" %)**0229(H) = 549(D) /100 = 54.9.**
--
--
  === 2.4.6  Leaf Temperature ===
++Get the temperature in the **Leaf**. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the **Leaf**. For example, if the data you get from the register is **__0x09 0xEC__**, the temperature content in the **Leaf **is
--Get the temperature in the Leaf. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the Leaf. For example, if the data you get from the register is (% style="color:#037691" %)**__0x09 0xEC__**(%%), the temperature content in the (% style="color:#037691" %)**Leaf **(%%)is
++**Example**:
--(% style="color:blue" %)**Example**:
++If payload is 0105H: ((0x0105 & 0x8000)>>15 === 0),temp = 0105(H)/10 = 26.1 °C
--If payload is **0105H**: ((0x0105 & 0x8000)>>15 === 0),temp = 0105(H)/10 = 26.1 °C
++If payload is FF7EH: ((FF7E & 0x8000)>>15 ===1),temp = (FF7E(H)-FFFF(H))/10 = -12.9 °C
--If payload is **FF7EH**: ((FF7E & 0x8000)>>15 ===1),temp = (FF7E(H)-FFFF(H))/10 = -12.9 °C
--
--
  === 2.4.7  Timestamp ===
--
  Time stamp : 0x6315537b =1662342011
  Convert Unix timestamp to time 2022-9-5 9:40:11.
--
  === 2.4.8  Digital Interrupt ===
++Digital Interrupt refers to pin **GPIO_EXTI**, and there are different trigger methods. When there is a trigger, the NLMS01 will send a packet to the server.
--Digital Interrupt refers to pin (% style="color:#037691" %)**GPIO_EXTI**(%%), and there are different trigger methods. When there is a trigger, the NLMS01 will send a packet to the server.
--
  The command is:
--(% style="color:blue" %)**AT+INTMOD=3 ** (%%)  ~/~/   (more info about INMOD please refer [[**AT Command Manual**>>url:https://www.dragino.com/downloads/downloads/NB-IoT/NBSN95/DRAGINO_NBSN95-NB_AT%20Commands_v1.1.0.pdf]])**.**
++**AT+INTMOD=3 **   ~/~/(more info about INMOD please refer [[**AT Command Manual**>>url:https://www.dragino.com/downloads/downloads/NB-IoT/NBSN95/DRAGINO_NBSN95-NB_AT%20Commands_v1.1.0.pdf]])**.**
  The lower four bits of this data field shows if this packet is generated by interrupt or not. Click here for the hardware and software set up.
@@ -415,15 +415,13 @@
 x(01): Interrupt Uplink Packet.
--
  === 2.4.9  +5V Output ===
--
  NLMS01 will enable +5V output before all sampling and disable the +5v after all sampling.
  The 5V output time can be controlled by AT Command.
--(% style="color:blue" %)**AT+5VT=1000**
++**AT+5VT=1000**
  Means set 5V valid time to have 1000ms. So the real 5V output will actually have 1000ms + sampling time for other sensors.** **
@@ -430,17 +430,14 @@
  == 2.5  Downlink Payload ==
--
  By default, NLMS01 prints the downlink payload to console port.
  [[image:image-20220907171221-18.png]]
++**Examples:**
--(% style="color:blue" %)**Examples:**
++* **Set TDC**
--
--* (% style="color:#037691" %)**Set TDC**
--
  If the payload=0100003C, it means set the END Node's TDC to 0x00003C=60(S), while type code is 01.
  Payload:    01 00 00 1E    TDC=30S
@@ -447,22 +447,16 @@
  Payload:    01 00 00 3C    TDC=60S
++* **Reset**
--
--* (% style="color:#037691" %)**Reset**
--
  If payload = 0x04FF, it will reset the NLMS01
++* **INTMOD**
--
--* (% style="color:#037691" %)**INTMOD**
--
  Downlink Payload: 06000003, Set AT+INTMOD=3
--
  == 2.6  LED Indicator ==
--
  The NLMS01 has an internal LED which is to show the status of different state.
  * When power on, NLMS01 will detect if sensor probe is connected, if probe detected, LED will blink four times. (no blinks in this step is no probe)
@@ -470,22 +470,18 @@
  * After NLMS01 join NB-IoT network. The LED will be ON for 3 seconds.
  * For each uplink probe, LED will be on for 500ms.
--== 2.7  Installation ==
++== 2.7 Installation ==
--
  NLMS01 probe has two sides. The side without words are the sense side. Please be ware when install the sensor.
--
  [[image:image-20220907171221-19.png]]
++== 2.8 Moisture and Temperature alarm function ==
--== 2.8  Moisture and Temperature alarm function ==
++➢ AT Command:
++AT+ HUMALARM =min,max
--(% style="color:blue" %)**➢ AT Command:**
--
--(% style="color:#037691" %)**AT+ HUMALARM =min,max**
--
  ² When min=0, and max≠0, Alarm higher than max
  ² When min≠0, and max=0, Alarm lower than min
@@ -492,9 +492,8 @@
  ² When min≠0 and max≠0, Alarm higher than max or lower than min
++Example:
--(% style="color:blue" %)**Example:**
--
  AT+ HUMALARM =50,60 ~/~/ Alarm when moisture lower than 50.
  AT+ TEMPALARM=min,max
@@ -505,199 +505,201 @@
  ² When min≠0 and max≠0, Alarm higher than max or lower than min
++Example:
--(% style="color:blue" %)**Example:**
--
  AT+ TEMPALARM=20,30 ~/~/ Alarm when temperature lower than 20.
--== 2.9  Set the number of data to be uploaded and the recording time ==
++== 2.9 Set the number of data to be uploaded and the recording time ==
++➢ AT Command:
--(% style="color:blue" %)**➢ AT Command:**
++AT+TR=900  ~/~/The unit is seconds, and the default is to record data once every 900 seconds.( The minimum can be set to 180 seconds)
--* (% style="color:#037691" %)**AT+TR=900**   (%%)  ~/~/  The unit is seconds, and the default is to record data once every 900 seconds.( The minimum can be set to 180 seconds)
--* (% style="color:#037691" %)**AT+NOUD=8**  (%%)~/~/   The device uploads 8 sets of recorded data by default. Up to 32 sets of record data can be uploaded.
++AT+NOUD=8  ~/~/The device uploads 8 sets of recorded data by default. Up to 32 sets of record data can be uploaded.
-- The diagram below explains the relationship between TR, NOUD, and TDC more clearly**:**
++== 2.10 Read or Clear cached data ==
--[[image:image-20221009001002-1.png||height="706" width="982"]]
++➢ AT Command:
++AT+CDP    ~/~/ Read cached data
--== 2.10  Read or Clear cached data ==
++[[image:image-20220907171221-20.png]]
--(% style="color:blue" %)**➢ AT Command:**
++AT+CDP=0    ~/~/ Clear cached data
--* (% style="color:#037691" %)**AT+CDP**      (%%)   ~/~/  Read cached data
--* (% style="color:#037691" %)**AT+CDP=0  ** (%%) ~/~/  Clear cached data
--[[image:image-20220907171221-20.png]]
++== 2.11  Firmware Change Log ==
++Download URL & Firmware Change log: [[https:~~/~~/www.dropbox.com/sh/1zmcakvbkf24f8x/AACmq2dZ3iRB9F1nVWeEB9Moa?dl=0>>url:https://www.dropbox.com/sh/1zmcakvbkf24f8x/AACmq2dZ3iRB9F1nVWeEB9Moa?dl=0]]
--== 2.11  Firmware Change Log ==
++Upgrade Instruction: [[Upgrade Firmware>>path:#H5.1200BHowtoUpgradeFirmware]]
++== 2.12  Battery Analysis ==
--Download URL & Firmware Change log: [[https:~~/~~/www.dropbox.com/sh/qdc3js2iu1vlipx/AACMHI3CvVb8g7YQMrIHY673a?dl=0>>https://www.dropbox.com/sh/qdc3js2iu1vlipx/AACMHI3CvVb8g7YQMrIHY673a?dl=0]]
++=== 2.12.1  Battery Type ===
--Upgrade Instruction: [[Upgrade Firmware>>||anchor="H5.1200BHowtoUpgradeFirmware"]]
++The NLMS01 battery is a combination of an 8500mAh Li/SOCI2 Battery and a Super Capacitor. The battery is none-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
++The battery is designed to last for several years depends on the actually use environment and update interval.
--== 2.12 Battery & Power Consumption ==
++The battery related documents as below:
++* [[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
++* [[Lithium-Thionyl Chloride Battery datasheet>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
++* [[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
--NLMS01 uses ER26500 + SPC1520 battery pack. See below link for detail information about the battery info and how to replace.
++[[image:image-20220907171221-21.png]]
--[[**Battery Info & Power Consumption Analyze**>>url:http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]] .
++=== 2.12.2  Power consumption Analyze ===
++Dragino battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
--= 3.  Access NB-IoT Module =
++Instruction to use as below:
++**Step 1:  **Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/]]
--Users can directly access the AT command set of the NB-IoT module.
++**Step 2: ** Open it and choose
--The AT Command set can refer the BC35-G NB-IoT Module AT Command: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/]]
++* Product Model
++* Uplink Interval
++* Working Mode
++And the Life expectation in difference case will be shown on the right.
--[[image:image-20220907171221-23.png]]
++[[image:image-20220907171221-22.jpeg]]
++=== 2.12.3  Battery Note ===
--= 4.  Using the AT Commands =
++The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
--== 4.1  Access AT Commands ==
++=== 2.12.4  Replace the battery ===
++The default battery pack of NLMS01 includes a ER26500 plus super capacitor. If user can't find this pack locally, they can find ER26500 or equivalence without the SPC1520 capacitor, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes).
--See this link for detail:  [[https:~~/~~/www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0>>url:https://www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0]]
++= 3.  Access NB-IoT Module =
--AT+<CMD>?    :  Help on <CMD>
++Users can directly access the AT command set of the NB-IoT module.
--AT+<CMD>   :    Run <CMD>
++The AT Command set can refer the BC35-G NB-IoT Module AT Command: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/]]
--AT+<CMD>=<value>:  Set the value
++[[image:image-20220907171221-23.png]]
--AT+<CMD>=?     :        Get the value
++= 4.  Using the AT Commands =
++== 4.1  Access AT Commands ==
--(% style="color:#037691" %)**General Commands**
++See this link for detail:  [[https:~~/~~/www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0>>url:https://www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0]]
--AT    :     Attention
++AT+<CMD>?                    : Help on <CMD>
--AT?   :    Short Help
++AT+<CMD>                      : Run <CMD>
--ATZ    :   MCU Reset
++AT+<CMD>=<value>      : Set the value
--AT+TDC   :  Application Data Transmission Interval
++AT+<CMD>=?                  : Get the value
--AT+CFG   :  Print all configurations
++**General Commands**
--AT+CFGMOD  :   Working mode selection
++AT                            : Attention
--AT+INTMOD  :    Set the trigger interrupt mode
++AT?                           : Short Help
--AT+5VT  :   Set extend the time of 5V power
++ATZ                          : MCU Reset
--AT+PRO :   Choose agreement
++AT+TDC                   : Application Data Transmission Interval
--AT+RXDL:   Extend the sending and receiving time
++AT+CFG                   : Print all configurations
--AT+SERVADDR :   Server Address
++AT+CFGMOD           : Working mode selection
--AT+APN :         Get or set the APN
++AT+INTMOD            : Set the trigger interrupt mode
--AT+FBAND :    Get or Set whether to automatically modify the frequency band
++AT+5VT                     : Set extend the time of 5V power
--AT+DNSCFG :  Get or Set DNS Server
++AT+PRO                    : Choose agreement
--AT+GETSENSORVALUE   : Returns the current sensor measurement
++AT+RXDL                   : Extend the sending and receiving time
--AT+TR :             Get or Set record time"
++AT+SERVADDR          : Server Address
--AT+NOUD :      Get or Set the number of data to be uploaded
++AT+APN            : Get or set the APN
--AT+CDP :          Read or Clear cached data
++AT+FBAND          : Get or Set whether to automatically modify the frequency band
--AT+TEMPALARM :  Get or Set alarm of temp
++AT+DNSCFG         :  Get or Set DNS Server
--AT+HUMALARM :  Get or Set alarm of humidity
++AT+GETSENSORVALUE   : Returns the current sensor measurement
++AT+TR      : Get or Set record time"
--(% style="color:#037691" %)**COAP Management**
++AT+NOUD      : Get or Set the number of data to be uploaded
--AT+URI :    Resource parameters
++AT+CDP     : Read or Clear cached data
++AT+TEMPALARM      : Get or Set alarm of temp
--(% style="color:#037691" %)**UDP Management**
++AT+HUMALARM     : Get or Set alarm of PH
--AT+CFM :  Upload confirmation mode (only valid for UDP)
++**COAP Management**
--(% style="color:#037691" %)**MQTT Management**
++AT+URI            : Resource parameters
--AT+CLIENT  :   Get or Set MQTT client
++**UDP Management**
--AT+UNAME  : Get or Set MQTT Username
++AT+CFM          : Upload confirmation mode (only valid for UDP)
--AT+PWD   :    Get or Set MQTT password
++**MQTT Management**
--AT+PUBTOPIC  :   Get or Set MQTT publish topic
++AT+CLIENT               : Get or Set MQTT client
--AT+SUBTOPIC :    Get or Set MQTT subscription topic
++AT+UNAME             : Get or Set MQTT Username
++AT+PWD                  : Get or Set MQTT password
--(% style="color:#037691" %)**Information**
++AT+PUBTOPIC          : Get or Set MQTT publish topic
--AT+FDR :          Factory Data Reset
++AT+SUBTOPIC          : Get or Set MQTT subscription topic
--AT+PWORD :   Serial Access Password
++**Information**
++AT+FDR              : Factory Data Reset
++AT+PWORD       : Serial Access Password
++
  = 5.  FAQ =
  == 5.1  How to Upgrade Firmware ==
--
  User can upgrade the firmware for 1) bug fix, 2) new feature release.
  Please see this link for how to upgrade:  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList]]
++**Notice, **NLMS01 **and **NLMS01 **share the same mother board. They use the same connection and method to update.**
--(% style="color:red" %)**Notice, NLMS01 and LLMS01 share the same mother board. They use the same connection and method to update.**
--
--
  = 6.  Trouble Shooting =
  == 6.1  Connection problem when uploading firmware ==
--
  **Please see: **[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting]]
--
  == 6.2  AT Command input doesn't work ==
++In the case if user can see the console output but can't type input to the device. Please check if you already include the **ENTER** while sending out the command. Some serial tool doesn't send **ENTER** while press the send key, user need to add ENTER in their string.
--In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
--
--
--== 6.3  Not able to connect to NB-IoT network and keep showing "Signal Strength:99". ==
--
--
--This means sensor is trying to join the NB-IoT network but fail. Please see this link for **//[[trouble shooting for signal strenght:99>>doc:Main.CSQ\:99,99.WebHome]]//**.
--
--
  = 7.  Order Info =
--
  Part Number**:** NLMS01
--
  = 8.  Packing Info =
++**Package Includes**:
--(% style="color:#037691" %)**Package Includes:**
--
  * NLMS01 NB-IoT  Leaf Moisture Sensor x 1
--(% style="color:#037691" %)**Dimension and weight**:
++**Dimension and weight**:
  * Device Size: cm
  * Device Weight: g
@@ -706,7 +706,6 @@
  = 9.  Support =
--
  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
  * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]

image-20221009001002-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Edwin

Size

...	...	@@ -1,1 +1,0 @@
1		-282.9 KB

Content

Changes for page NLMS01-NB-IoT Leaf Moisture Sensor User Manual

Summary

Details

Applications

Navigation