Changes for page NLMS01-NB-IoT Leaf Moisture Sensor User Manual
Last modified by Mengting Qiu on 2024/04/02 16:54
Change comment:
There is no comment for this version
Summary
-
Page properties (2 modified, 0 added, 0 removed)
-
Attachments (0 modified, 0 added, 2 removed)
Details
- Page properties
-
- Author
-
... ... @@ -1,1 +1,1 @@ 1 -XWiki. Xiaoling1 +XWiki.Edwin - Content
-
... ... @@ -7,80 +7,89 @@ 7 7 8 8 9 9 10 -= 1. 10 += 1. Introduction = 11 11 12 +== 1.1 What is NLMS01 Leaf Moisture Sensor == 12 12 13 -== 1.1 What is NLMS01 Leaf Moisture Sensor == 14 14 15 +The Dragino NLMS01 is a **NB-IOT Leaf Moisture Sensor** for IoT of Agriculture. It is designed to measure the leaf moisture and temperature, so to send to the platform to analyze the leaf status such as : watering, moisturizing, dew, frozen. The probe is IP67 waterproof. 15 15 16 -((( 17 -The Dragino NLMS01 is a (% style="color:blue" %)**NB-IOT Leaf Moisture Sensor**(%%) for IoT of Agriculture. It is designed to measure the leaf moisture and temperature, so to send to the platform to analyze the leaf status such as : watering, moisturizing, dew, frozen. The probe is IP67 waterproof. 17 +NLMS01 detects leaf's** moisture and temperature **use FDR method, it senses the dielectric constant cause by liquid over the leaf surface, and cover the value to leaf moisture. The probe is design in a leaf shape to best simulate the real leaf characterizes. The probe has as density as 15 leaf vein lines per centimeter which make it can senses small drop and more accuracy. 18 18 19 -NLMS01 detects leaf's(% style="color:blue" %)** moisture and temperature use FDR method**(%%), it senses the dielectric constant cause by liquid over the leaf surface, and cover the value to leaf moisture. The probe is design in a leaf shape to best simulate the real leaf characterizes. The probe has as density as 15 leaf vein lines per centimeter which make it can senses small drop and more accuracy. 20 - 21 21 NarrowBand-Internet of Things (NB-IoT) is a standards-based low power wide area (LPWA) technology developed to enable a wide range of new IoT devices and services. NB-IoT significantly improves the power consumption of user devices, system capacity and spectrum efficiency, especially in deep coverage. 20 +\\NLMS01 supports different uplink methods include **TCP,MQTT,UDP and CoAP **for different application requirement. 21 +\\NLMS01 is powered by **8500mAh Li-SOCI2 battery**, It is designed for long term use up to 5 years. (Actually Battery life depends on the use environment, update period & uplink method) 22 +\\To use NLMS01, user needs to check if there is NB-IoT coverage in local area and with the bands NLMS01 supports. If the local operate support it, user needs to get a **NB-IoT SIM card** from local operator and install NLMS01 to get NB-IoT network connection 22 22 23 -NLMS01 supports different uplink methods include (% style="color:blue" %)**TCP,MQTT,UDP and CoAP **(%%)for different application requirement. 24 - 25 -NLMS01 is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), It is designed for long term use up to 5 years. (Actually Battery life depends on the use environment, update period & uplink method). 26 - 27 -To use NLMS01, user needs to check if there is NB-IoT coverage in local area and with the bands NLMS01 supports. If the local operate support it, user needs to get a (% style="color:blue" %)**NB-IoT SIM card**(%%) from local operator and install NLMS01 to get NB-IoT network connection. 28 -))) 29 - 30 - 31 31 [[image:image-20220907171221-2.png]] 32 32 33 - 34 34 [[image:image-20220907171221-3.png]] 35 35 28 +== 1.2 Features == 36 36 37 -== 1.2 Features == 30 +* ((( 31 +NB-IoT Bands: B1/B3/B8/B5/B20/B28 @H-FDD 32 +))) 33 +* ((( 34 +Monitor Leaf moisture 35 +))) 38 38 37 +* ((( 38 + Monitor Leaf temperature 39 +))) 39 39 40 -* NB-IoT Bands: B1/B3/B8/B5/B20/B28 @H-FDD 41 -* Monitor Leaf moisture 42 -* Monitor Leaf temperature 43 -* Moisture and Temperature alarm function 44 -* Monitor Battery Level 45 -* Uplink on periodically 46 -* Downlink to change configure 47 -* IP66 Waterproof Enclosure 48 -* IP67 rate for the Sensor Probe 49 -* Ultra-Low Power consumption 50 -* AT Commands to change parameters 51 -* Micro SIM card slot for NB-IoT SIM 52 -* 8500mAh Battery for long term use 53 - 54 -((( 55 - 56 - 57 - 41 +* ((( 42 +Moisture and Temperature alarm function 58 58 ))) 44 +* ((( 45 +Monitor Battery Level 46 +))) 47 +* ((( 48 +Uplink on periodically 49 +))) 50 +* ((( 51 +Downlink to change configure 52 +))) 53 +* ((( 54 +IP66 Waterproof Enclosure 55 +))) 56 +* ((( 57 +IP67 rate for the Sensor Probe 58 +))) 59 +* ((( 60 +Ultra-Low Power consumption 61 +))) 62 +* ((( 63 +AT Commands to change parameters 64 +))) 65 +* ((( 66 +Micro SIM card slot for NB-IoT SIM 67 +))) 68 +* ((( 69 +8500mAh Battery for long term use 70 +))) 59 59 60 60 == 1.3 Specification == 61 61 74 +**Common DC Characteristics:** 62 62 63 -(% style="color:#037691" %)**Common DC Characteristics:** 64 - 65 65 * Supply Voltage: 2.1v ~~ 3.6v 66 66 * Operating Temperature: -40 ~~ 85°C 67 67 68 - (% style="color:#037691" %)**NB-IoT Spec:**79 +**NB-IoT Spec:** 69 69 70 -* B1 @H-FDD: 2100MHz 71 -* B3 @H-FDD: 1800MHz 72 -* B8 @H-FDD: 900MHz 73 -* B5 @H-FDD: 850MHz 74 -* B20 @H-FDD: 800MHz 75 -* B28 @H-FDD: 700MHz 81 +* - B1 @H-FDD: 2100MHz 82 +* - B3 @H-FDD: 1800MHz 83 +* - B8 @H-FDD: 900MHz 84 +* - B5 @H-FDD: 850MHz 85 +* - B20 @H-FDD: 800MHz 86 +* - B28 @H-FDD: 700MHz 76 76 88 +== 1.4 Probe Specification == 77 77 78 78 79 - ==1.4 ProbeSpecification==91 +**Leaf Moisture: percentage of water drop over total leaf surface** 80 80 81 - 82 -(% style="color:#037691" %)**Leaf Moisture: percentage of water drop over total leaf surface** 83 - 84 84 * Range 0-100% 85 85 * Resolution: 0.1% 86 86 * Accuracy: ±3%(0-50%);±6%(>50%) ... ... @@ -87,7 +87,7 @@ 87 87 * IP67 Protection 88 88 * Length: 3.5 meters 89 89 90 - (% style="color:#037691" %)**Leaf Temperature:**99 +**Leaf Temperature:** 91 91 92 92 * Range -50℃~80℃ 93 93 * Resolution: 0.1℃ ... ... @@ -95,18 +95,12 @@ 95 95 * IP67 Protection 96 96 * Length: 3.5 meters 97 97 107 +== 1.5 Applications == 98 98 99 - 100 -== 1.5 Applications == 101 - 102 - 103 103 * Smart Agriculture 104 104 111 +== 1.6 Pin mapping and power on == 105 105 106 - 107 -== 1.6 Pin mapping and power on == 108 - 109 - 110 110 [[image:image-20220907171221-4.png]] 111 111 112 112 **~ ** ... ... @@ -115,20 +115,16 @@ 115 115 116 116 == 2.1 How it works == 117 117 118 - 119 119 The NLMS01 is equipped with a NB-IoT module, the pre-loaded firmware in NLMS01 will get environment data from sensors and send the value to local NB-IoT network via the NB-IoT module. The NB-IoT network will forward this value to IoT server via the protocol defined by NLMS01. 120 120 121 121 The diagram below shows the working flow in default firmware of NLMS01: 122 122 123 - 124 124 [[image:image-20220907171221-5.png]] 125 125 126 - 127 127 == 2.2 Configure the NLMS01 == 128 128 129 129 === 2.2.1 Test Requirement === 130 130 131 - 132 132 To use NLMS01 in your city, make sure meet below requirements: 133 133 134 134 * Your local operator has already distributed a NB-IoT Network there. ... ... @@ -135,88 +135,72 @@ 135 135 * The local NB-IoT network used the band that NLMS01 supports. 136 136 * Your operator is able to distribute the data received in their NB-IoT network to your IoT server. 137 137 138 -Below figure shows our testing structure. Here we have NB-IoT network coverage by China Mobile, the band they use is B8. The NLMS01 will use (%style="color:#037691" %)**CoAP(120.24.4.116:5683)**(%%)or raw(%style="color:#037691" %)**UDP(120.24.4.116:5601)** or(%%)(% style="color:#037691"%)**MQTT(120.24.4.116:1883)**(%%)or(% style="color:#037691" %)**TCP(120.24.4.116:5600)**(%%)protocol to send data to the test server137 +Below figure shows our testing structure. Here we have NB-IoT network coverage by China Mobile, the band they use is B8. The NLMS01 will use CoAP(120.24.4.116:5683) or raw UDP(120.24.4.116:5601) or MQTT(120.24.4.116:1883)or TCP(120.24.4.116:5600)protocol to send data to the test server 139 139 140 - 141 141 [[image:image-20220907171221-6.png]] 142 142 143 - 144 144 === 2.2.2 Insert SIM card === 145 145 146 - 147 147 Insert the NB-IoT Card get from your provider. 148 148 149 149 User need to take out the NB-IoT module and insert the SIM card like below: 150 150 151 - 152 152 [[image:image-20220907171221-7.png]] 153 153 154 - 155 155 === 2.2.3 Connect USB – TTL to NLMS01 to configure it === 156 156 151 +User need to configure NLMS01 via serial port to set the **Server Address** / **Uplink Topic** to define where and how-to uplink packets. NLMS01 support AT Commands, user can use a USB to TTL adapter to connect to NLMS01 and use AT Commands to configure it, as below. 157 157 158 - User need to configure NLMS01 via serial port to set the (% style="color:#037691" %)**Server Address** / **Uplink Topic** (%%)to define where and how-to uplink packets. NLMS01 support ATCommands, user canusea USB to TTL adapter toconnectto NLMS01 and use AT Commands to configure it, as below.153 +**Connection:** 159 159 155 + USB TTL GND <~-~-~-~-> GND 160 160 161 - (%style="color:blue"%)**Connection:**157 + USB TTL TXD <~-~-~-~-> UART_RXD 162 162 163 - **~(% style="background-color:yellow" %)USB TTLGND <~-~-~-~->GND(%%)**159 + USB TTL RXD <~-~-~-~-> UART_TXD 164 164 165 -**~ (% style="background-color:yellow" %)USB TTL TXD <~-~-~-~-> UART_RXD(%%)** 166 - 167 -**~ (% style="background-color:yellow" %)USB TTL RXD <~-~-~-~-> UART_TXD(%%)** 168 - 169 - 170 170 In the PC, use below serial tool settings: 171 171 172 -* Baud: (% style="color:green" %)**9600**173 -* Data bits:** (% style="color:green" %)8(%%)**174 -* Stop bits: (% style="color:green" %)**1**175 -* Parity: (% style="color:green" %)**None**176 -* Flow Control: (% style="color:green" %)**None**163 +* Baud: **9600** 164 +* Data bits:** 8** 165 +* Stop bits: **1** 166 +* Parity: **None** 167 +* Flow Control: **None** 177 177 178 -Make sure the switch is in FLASH position, then power on device by connecting the jumper on NLMS01. NLMS01 will output system info once power on as below, we can enter the (% style="color:green" %)**password: 12345678**(%%)to access AT Command input.169 +Make sure the switch is in FLASH position, then power on device by connecting the jumper on NLMS01. NLMS01 will output system info once power on as below, we can enter the **password: 12345678** to access AT Command input. 179 179 180 -[[image:image-202209 13090720-1.png]]171 +[[image:image-20220907171221-8.png]] 181 181 173 +**Note: the valid AT Commands can be found at: **[[**https:~~/~~/www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0**>>url:https://www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0]] 182 182 183 -(% style="color:red" %)**Note: the valid AT Commands can be found at: **(%%)[[**https:~~/~~/www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0**>>url:https://www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0]] 184 - 185 - 186 186 === 2.2.4 Use CoAP protocol to uplink data === 187 187 177 +**Note: if you don't have CoAP server, you can refer this link to set up one: **[[**http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/**>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/]] 188 188 189 - (% style="color:red" %)**Note: if you don't have CoAPserver,you can refer thislink toset up one: **(%%)[[**http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/**>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/]]179 +**Use below commands:** 190 190 181 +* **AT+PRO=1** ~/~/ Set to use CoAP protocol to uplink 182 +* **AT+SERVADDR=120.24.4.116,5683 ** ~/~/ to set CoAP server address and port 183 +* **AT+URI=5,11,"mqtt",11,"coap",12,"0",15,"c=text1",23,"0" ** ~/~/Set COAP resource path 191 191 192 -(% style="color:blue" %)**Use below commands:** 193 - 194 -* (% style="color:#037691" %)**AT+PRO=1** (%%) ~/~/ Set to use CoAP protocol to uplink 195 -* (% style="color:#037691" %)**AT+SERVADDR=120.24.4.116,5683 ** (%%) ~/~/ to set CoAP server address and port 196 -* (% style="color:#037691" %)**AT+URI=5,11,"mqtt",11,"coap",12,"0",15,"c=text1",23,"0" ** (%%) ~/~/ Set COAP resource path 197 - 198 198 For parameter description, please refer to AT command set 199 199 200 200 [[image:image-20220907171221-9.png]] 201 201 189 +After configure the server address and **reset the device** (via AT+ATZ ), NLMS01 will start to uplink sensor values to CoAP server. 202 202 203 -After configure the server address and (% style="color:#037691" %)**reset the device**(%%) (via AT+ATZ ), NLMS01 will start to uplink sensor values to CoAP server. 204 - 205 205 [[image:image-20220907171221-10.png]] 206 206 207 - 208 208 === 2.2.5 Use UDP protocol to uplink data(Default protocol) === 209 209 210 - 211 211 This feature is supported since firmware version v1.0.1 212 212 213 -* (% style="color:#037691" %)**AT+PRO=2 **(%%)~/~/214 -* (% style="color:#037691" %)**AT+SERVADDR=120.24.4.116,5601(%%)~/~/215 -* (% style="color:#037691" %)**AT+CFM=1 **(%%)~/~/197 +* **AT+PRO=2 ** ~/~/ Set to use UDP protocol to uplink 198 +* **AT+SERVADDR=120.24.4.116,5601 ** ~/~/ to set UDP server address and port 199 +* **AT+CFM=1 ** ~/~/If the server does not respond, this command is unnecessary 216 216 217 217 [[image:image-20220907171221-11.png]] 218 218 219 - 220 220 [[image:image-20220907171221-12.png]] 221 221 222 222 ... ... @@ -223,21 +223,18 @@ 223 223 224 224 === 2.2.6 Use MQTT protocol to uplink data === 225 225 226 - 227 227 This feature is supported since firmware version v110 228 228 229 -* (% style="color:#037691" %)**AT+PRO=3 **(%%)~/~/230 -* (% style="color:#037691" %)**AT+SERVADDR=120.24.4.116,1883 **(%%)~/~/231 -* (% style="color:#037691" %)**AT+CLIENT=CLIENT **(%%)~/~/232 -* (% style="color:#037691" %)**AT+UNAME=UNAME **(%%)** **~/~/233 -* (% style="color:#037691" %)**AT+PWD=PWD **(%%)** **~/~/234 -* (% style="color:#037691" %)**AT+PUBTOPIC=PUB **(%%)~/~/235 -* (% style="color:#037691" %)**AT+SUBTOPIC=SUB **(%%)211 +* **AT+PRO=3 ** ~/~/Set to use MQTT protocol to uplink 212 +* **AT+SERVADDR=120.24.4.116,1883 ** ~/~/Set MQTT server address and port 213 +* **AT+CLIENT=CLIENT ** ~/~/Set up the CLIENT of MQTT 214 +* **AT+UNAME=UNAME **~/~/Set the username of MQTT 215 +* **AT+PWD=PWD **~/~/Set the password of MQTT 216 +* **AT+PUBTOPIC=PUB **~/~/Set the sending topic of MQTT 217 +* **AT+SUBTOPIC=SUB ** ~/~/Set the subscription topic of MQTT 236 236 237 237 [[image:image-20220907171221-13.png]] 238 238 239 - 240 - 241 241 [[image:image-20220907171221-14.png]] 242 242 243 243 ... ... @@ -244,110 +244,79 @@ 244 244 245 245 MQTT protocol has a much higher power consumption compare vs UDP / CoAP protocol. Please check the power analyze document and adjust the uplink period to a suitable interval. 246 246 247 - 248 248 === 2.2.7 Use TCP protocol to uplink data === 249 249 250 - 251 251 This feature is supported since firmware version v110 252 252 253 -* (% style="color:#037691" %)**AT+PRO=4 **(%%)~/~/254 -* (% style="color:#037691" %)**AT+SERVADDR=120.24.4.116,5600 **(%%)~/~/231 +* **AT+PRO=4 ** ~/~/ Set to use TCP protocol to uplink 232 +* **AT+SERVADDR=120.24.4.116,5600 ** ~/~/ to set TCP server address and port 255 255 256 256 [[image:image-20220907171221-15.png]] 257 257 258 - 259 - 260 260 [[image:image-20220907171221-16.png]] 261 261 262 262 263 263 264 - 265 265 === 2.2.8 Change Update Interval === 266 266 267 - 268 268 User can use below command to change the **uplink interval**. 269 269 270 -* (% style="color:#037691" %)**AT+TDC=7200 **(%%)~/~/ Set Update Interval to 7200s (2 hour)244 +* **AT+TDC=7200 ** ~/~/ Set Update Interval to 7200s (2 hour) 271 271 272 - (% style="color:red" %)**NOTE: By default, the device will send an uplink message every 2 hour. Each Uplink Include 8 set of records in this 2 hour (15 minute interval / record).**246 +**NOTE: By default, the device will send an uplink message every 2 hour. Each Uplink Include 8 set of records in this 2 hour (15 minute interval / record).** 273 273 274 274 275 275 == 2.3 Uplink Payload == 276 276 277 - 278 278 In this mode, uplink payload includes 87 bytes in total by default. 279 279 280 280 Each time the device uploads a data package, 8 sets of recorded data will be attached. Up to 32 sets of recorded data can be uploaded. 281 281 255 +|**Size(bytes)**|**8**|**2**|**2**|1|1|1|2|2|4|2|2|4 256 +|**Value**|Device ID|Ver|BAT|Signal Strength|MOD|Interrupt|Leaf moisture|Leaf Temperature|Time stamp|Leaf Temperature|Leaf moisture|Time stamp ..... 282 282 283 -(% border="1" style="background-color:#ffffcc; color:green; width:520px" %) 284 -|=(% scope="row" style="width: 50px;" %)**Size(bytes)**|(% style="width:40px" %)**8**|(% style="width:20px" %)**2**|(% style="width:20px" %)**2**|(% style="width:60px" %)**1**|(% style="width:20px" %)**1**|(% style="width:40px" %)**1**|(% style="width:40px" %)**2**|(% style="width:50px" %)**2**|(% style="width:50px" %)**4**|(% style="width:50px" %)**2**|(% style="width:40px" %)**2**|(% style="width:40px" %)**4** 285 -|=(% style="width: 96px;" %)**Value**|(% style="width:82px" %)Device ID|(% style="width:42px" %)Ver|(% style="width:48px" %)BAT|(% style="width:124px" %)Signal Strength|(% style="width:58px" %)MOD|(% style="width:82px" %)Interrupt|(% style="width:113px" %)Leaf moisture|(% style="width:134px" %)Leaf Temperature|(% style="width:100px" %)Time stamp|(% style="width:137px" %)Leaf Temperature|(% style="width:110px" %)Leaf moisture|(% style="width:122px" %)Time stamp ..... 286 - 287 287 If we use the MQTT client to subscribe to this MQTT topic, we can see the following information when the NLMS01 uplink data. 288 288 289 - 290 290 [[image:image-20220907171221-17.png]] 291 291 292 - 293 293 The payload is ASCII string, representative same HEX: 294 294 295 - **0x__f868411056754138__(% style="color:blue" %)__0064__(% style="color:green" %)__0c78__(% style="color:#00b0f0" %)__17__(% style="color:#7030a0" %)__01__(% style="color:#d60093" %)__00__(% style="color:#a14d07" %)__0225__ (% style="color:#0020b0" %) __010b__ (% style="color:#420042" %)__6315537b__ (% style="color:#663300" %)//__010b0226631550fb__ __010e022663154d77__//(%%)**264 +0x(% style="color:red" %)f868411056754138(% style="color:blue" %)0064(% style="color:green" %)0c78(% style="color:red" %)17(% style="color:blue" %)01(% style="color:green" %)00(% style="color:blue" %)**0225010b6315537b**010b0226631550fb**010e022663154d77**01110225631549f1**011502246315466b**01190223631542e5**011d022163153f62**011e022163153bde**011e022163153859**(%%)** **where: 296 296 297 -where: 266 +* (% style="color:red" %)Device ID: 0xf868411056754138 = f868411056754138 267 +* (% style="color:blue" %)Version: 0x0064=100=1.0.0 268 +* (% style="color:green" %)BAT: 0x0c78 = 3192 mV = 3.192V 269 +* (% style="color:red" %)Singal: 0x17 = 23 270 +* (% style="color:blue" %)Mod: 0x01 = 1 271 +* (% style="color:green" %)Interrupt: 0x00= 0 272 +* Leaf moisture: 0x0225= 549 = 54.9% 273 +* Leaf Temperature:0x010B =267=26.7 °C 274 +* Time stamp : 0x6315537b =1662342011 275 +* Leaf Temperature, Leaf moisture,Time stamp : 010b0226631550fb 276 +* (% style="color:blue" %)8 sets of recorded data: Leaf Temperature, Leaf moisture,Time stamp : 010e022663154d77,....... 298 298 299 -* (% style="color:#037691" %)**Device ID:**(%%) 0xf868411056754138 = f868411056754138 300 - 301 -* (% style="color:#037691" %)**Version:**(%%) 0x0064=100=1.0.0 302 - 303 -* (% style="color:#037691" %)**BAT:** (%%)0x0c78 = 3192 mV = 3.192V 304 - 305 -* (% style="color:#037691" %)**Singal:**(%%) 0x17 = 23 306 - 307 -* (% style="color:#037691" %)**Mod:**(%%) 0x01 = 1 308 - 309 -* (% style="color:#037691" %)**Interrupt:**(%%) 0x00= 0 310 - 311 -* (% style="color:#037691" %)**Leaf moisture:**(%%) 0x0225= 549 = 54.9% 312 - 313 -* (% style="color:#037691" %)**Leaf Temperature: **(%%)0x010B =267=26.7 °C 314 - 315 -* (% style="color:#037691" %)**Time stamp :** (%%)0x6315537b =1662342011 ([[Unix Epoch Time>>https://www.epochconverter.com/]]) 316 - 317 -* (% style="color:#037691" %)**Leaf Temperature, Leaf moisture,Time stamp : **(%%)010b0226631550fb 318 - 319 -* (% style="color:#037691" %)**8 sets of recorded data: **(%%)Leaf Temperature, Leaf moisture,Time stamp : 010e022663154d77,....... 320 - 321 - 322 - 323 323 == 2.4 Payload Explanation and Sensor Interface == 324 324 325 325 === 2.4.1 Device ID === 326 326 327 - 328 328 By default, the Device ID equal to the last 15 bits of IMEI. 329 329 330 -User can use (% style="color:#037691" %)**AT+DEUI**(%%)to set Device ID284 +User can use **AT+DEUI** to set Device ID 331 331 286 +**Example:** 332 332 333 -(% style="color:blue" %)**Example**: 334 - 335 335 AT+DEUI=868411056754138 336 336 337 337 The Device ID is stored in a none-erase area, Upgrade the firmware or run AT+FDR won't erase Device ID. 338 338 339 - 340 340 === 2.4.2 Version Info === 341 341 342 - 343 343 Specify the software version: 0x64=100, means firmware version 1.00. 344 344 345 345 For example: 0x00 64 : this device is NLMS01 with firmware version 1.0.0. 346 346 347 - 348 348 === 2.4.3 Battery Info === 349 349 350 - 351 351 Check the battery voltage for NLMS01. 352 352 353 353 Ex1: 0x0B45 = 2885mV ... ... @@ -354,15 +354,12 @@ 354 354 355 355 Ex2: 0x0B49 = 2889mV 356 356 357 - 358 358 === 2.4.4 Signal Strength === 359 359 360 - 361 361 NB-IoT Network signal Strength. 362 362 310 +**Ex1: 0x1d = 29** 363 363 364 -(% style="color:blue" %)**Ex1: 0x1d = 29** 365 - 366 366 **0** -113dBm or less 367 367 368 368 **1** -111dBm ... ... @@ -373,45 +373,37 @@ 373 373 374 374 **99** Not known or not detectable 375 375 376 - 377 377 === 2.4.5 Leaf moisture === 378 378 324 +Get the moisture of the **Leaf**. The value range of the register is 300-1000(Decimal), divide this value by 100 to get the percentage of moisture in the **Leaf**. 379 379 380 - Gettheoistureof the(% style="color:#037691" %)**Leaf**(%%).The valuerangeof the register is300-1000(Decimal),dividethis valueby 100 togetthepercentageof moisturein the Leaf.326 +For example, if the data you get from the register is **__0x05 0xDC__**, the moisture content in the **Leaf** is 381 381 382 - For example, if the data you get from the register is (% style="color:#037691" %)**__0x05 0xDC__**(%%),themoisture content in the(%style="color:#037691"%)**Leaf**(%%) is328 +**0229(H) = 549(D) /100 = 54.9.** 383 383 384 -(% style="color:blue" %)**0229(H) = 549(D) /100 = 54.9.** 385 - 386 - 387 387 === 2.4.6 Leaf Temperature === 388 388 332 +Get the temperature in the **Leaf**. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the **Leaf**. For example, if the data you get from the register is **__0x09 0xEC__**, the temperature content in the **Leaf **is 389 389 390 - Get the temperature in the Leaf. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the Leaf. For example, if the data you get from the register is (% style="color:#037691" %)**__0x09 0xEC__**(%%), the temperature content in the (% style="color:#037691" %)**Leaf **(%%)is334 +**Example**: 391 391 392 - (%style="color:blue"%)**Example**:336 +If payload is 0105H: ((0x0105 & 0x8000)>>15 === 0),temp = 0105(H)/10 = 26.1 °C 393 393 394 -If payload is **0105H**: ((0x0105& 0x8000)>>15 ===0),temp =0105(H)/10 = 26.1°C338 +If payload is FF7EH: ((FF7E & 0x8000)>>15 ===1),temp = (FF7E(H)-FFFF(H))/10 = -12.9 °C 395 395 396 -If payload is **FF7EH**: ((FF7E & 0x8000)>>15 ===1),temp = (FF7E(H)-FFFF(H))/10 = -12.9 °C 397 - 398 - 399 399 === 2.4.7 Timestamp === 400 400 401 - 402 402 Time stamp : 0x6315537b =1662342011 403 403 404 404 Convert Unix timestamp to time 2022-9-5 9:40:11. 405 405 406 - 407 407 === 2.4.8 Digital Interrupt === 408 408 348 +Digital Interrupt refers to pin **GPIO_EXTI**, and there are different trigger methods. When there is a trigger, the NLMS01 will send a packet to the server. 409 409 410 -Digital Interrupt refers to pin (% style="color:#037691" %)**GPIO_EXTI**(%%), and there are different trigger methods. When there is a trigger, the NLMS01 will send a packet to the server. 411 - 412 412 The command is: 413 413 414 - (% style="color:blue" %)**AT+INTMOD=3 **(%%)~/~/352 +**AT+INTMOD=3 ** ~/~/(more info about INMOD please refer [[**AT Command Manual**>>url:https://www.dragino.com/downloads/downloads/NB-IoT/NBSN95/DRAGINO_NBSN95-NB_AT%20Commands_v1.1.0.pdf]])**.** 415 415 416 416 The lower four bits of this data field shows if this packet is generated by interrupt or not. Click here for the hardware and software set up. 417 417 ... ... @@ -421,15 +421,13 @@ 421 421 422 422 0x(01): Interrupt Uplink Packet. 423 423 424 - 425 425 === 2.4.9 +5V Output === 426 426 427 - 428 428 NLMS01 will enable +5V output before all sampling and disable the +5v after all sampling. 429 429 430 430 The 5V output time can be controlled by AT Command. 431 431 432 - (% style="color:blue" %)**AT+5VT=1000**368 +**AT+5VT=1000** 433 433 434 434 Means set 5V valid time to have 1000ms. So the real 5V output will actually have 1000ms + sampling time for other sensors.** ** 435 435 ... ... @@ -436,17 +436,14 @@ 436 436 437 437 == 2.5 Downlink Payload == 438 438 439 - 440 440 By default, NLMS01 prints the downlink payload to console port. 441 441 442 442 [[image:image-20220907171221-18.png]] 443 443 379 +**Examples:** 444 444 445 - (%style="color:blue" %)**Examples:**381 +* **Set TDC** 446 446 447 - 448 -* (% style="color:#037691" %)**Set TDC** 449 - 450 450 If the payload=0100003C, it means set the END Node's TDC to 0x00003C=60(S), while type code is 01. 451 451 452 452 Payload: 01 00 00 1E TDC=30S ... ... @@ -453,22 +453,16 @@ 453 453 454 454 Payload: 01 00 00 3C TDC=60S 455 455 389 +* **Reset** 456 456 457 - 458 -* (% style="color:#037691" %)**Reset** 459 - 460 460 If payload = 0x04FF, it will reset the NLMS01 461 461 393 +* **INTMOD** 462 462 463 - 464 -* (% style="color:#037691" %)**INTMOD** 465 - 466 466 Downlink Payload: 06000003, Set AT+INTMOD=3 467 467 468 - 469 469 == 2.6 LED Indicator == 470 470 471 - 472 472 The NLMS01 has an internal LED which is to show the status of different state. 473 473 474 474 * When power on, NLMS01 will detect if sensor probe is connected, if probe detected, LED will blink four times. (no blinks in this step is no probe) ... ... @@ -476,24 +476,18 @@ 476 476 * After NLMS01 join NB-IoT network. The LED will be ON for 3 seconds. 477 477 * For each uplink probe, LED will be on for 500ms. 478 478 406 +== 2.7 Installation == 479 479 480 - 481 -== 2.7 Installation == 482 - 483 - 484 484 NLMS01 probe has two sides. The side without words are the sense side. Please be ware when install the sensor. 485 485 486 - 487 487 [[image:image-20220907171221-19.png]] 488 488 412 +== 2.8 Moisture and Temperature alarm function == 489 489 490 - ==2.8Moisture and Temperature alarmfunction ==414 +➢ AT Command: 491 491 416 +AT+ HUMALARM =min,max 492 492 493 -(% style="color:blue" %)**➢ AT Command:** 494 - 495 -(% style="color:#037691" %)**AT+ HUMALARM =min,max** 496 - 497 497 ² When min=0, and max≠0, Alarm higher than max 498 498 499 499 ² When min≠0, and max=0, Alarm lower than min ... ... @@ -500,9 +500,8 @@ 500 500 501 501 ² When min≠0 and max≠0, Alarm higher than max or lower than min 502 502 424 +Example: 503 503 504 -(% style="color:blue" %)**Example:** 505 - 506 506 AT+ HUMALARM =50,60 ~/~/ Alarm when moisture lower than 50. 507 507 508 508 AT+ TEMPALARM=min,max ... ... @@ -513,193 +513,196 @@ 513 513 514 514 ² When min≠0 and max≠0, Alarm higher than max or lower than min 515 515 436 +Example: 516 516 517 -(% style="color:blue" %)**Example:** 518 - 519 519 AT+ TEMPALARM=20,30 ~/~/ Alarm when temperature lower than 20. 520 520 521 521 522 -== 2.9 441 +== 2.9 Set the number of data to be uploaded and the recording time == 523 523 443 +➢ AT Command: 524 524 525 - (%style="color:blue"%)**➢ATCommand:**445 +AT+TR=900 ~/~/The unit is seconds, and the default is to record data once every 900 seconds.( The minimum can be set to 180 seconds) 526 526 527 -* (% style="color:#037691" %)**AT+TR=900** (%%) ~/~/ The unit is seconds, and the default is to record data once every 900 seconds.( The minimum can be set to 180 seconds) 528 -* (% style="color:#037691" %)**AT+NOUD=8** (%%)~/~/ The device uploads 8 sets of recorded data by default. Up to 32 sets of record data can be uploaded. 447 +AT+NOUD=8 ~/~/The device uploads 8 sets of recorded data by default. Up to 32 sets of record data can be uploaded. 529 529 530 - Thediagrambelowexplainstherelationship between TR, NOUD,andTDC more clearly**:**449 +== 2.10 Read or Clear cached data == 531 531 532 - [[image:image-20221009001002-1.png||height="706" width="982"]]451 +➢ AT Command: 533 533 453 +AT+CDP ~/~/ Read cached data 534 534 535 - == 2.10 Read or Clear cached data ==455 +[[image:image-20220907171221-20.png]] 536 536 537 537 538 - (%style="color:blue"%)**➢ AT Command:**458 +AT+CDP=0 ~/~/ Clear cached data 539 539 540 -* (% style="color:#037691" %)**AT+CDP** (%%) ~/~/ Read cached data 541 -* (% style="color:#037691" %)**AT+CDP=0 ** (%%) ~/~/ Clear cached data 542 542 543 - [[image:image-20220907171221-20.png]]461 +== 2.11 Firmware Change Log == 544 544 463 +Download URL & Firmware Change log: [[https:~~/~~/www.dropbox.com/sh/1zmcakvbkf24f8x/AACmq2dZ3iRB9F1nVWeEB9Moa?dl=0>>url:https://www.dropbox.com/sh/1zmcakvbkf24f8x/AACmq2dZ3iRB9F1nVWeEB9Moa?dl=0]] 545 545 546 - ==2.11FirmwareChange Log==465 +Upgrade Instruction: [[Upgrade Firmware>>path:#H5.1200BHowtoUpgradeFirmware]] 547 547 467 +== 2.12 Battery Analysis == 548 548 549 - DownloadURL & Firmware Change log: [[https:~~/~~/www.dropbox.com/sh/qdc3js2iu1vlipx/AACMHI3CvVb8g7YQMrIHY673a?dl=0>>https://www.dropbox.com/sh/qdc3js2iu1vlipx/AACMHI3CvVb8g7YQMrIHY673a?dl=0]]469 +=== 2.12.1 Battery Type === 550 550 551 - UpgradeInstruction:[[UpgradeFirmware>>||anchor="H5.1200BHowtoUpgradeFirmware"]]471 +The NLMS01 battery is a combination of an 8500mAh Li/SOCI2 Battery and a Super Capacitor. The battery is none-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter. 552 552 473 +The battery is designed to last for several years depends on the actually use environment and update interval. 553 553 554 - ==2.12 Battery& PowerConsumption==475 +The battery related documents as below: 555 555 477 +* [[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]] 478 +* [[Lithium-Thionyl Chloride Battery datasheet>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]] 479 +* [[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]] 556 556 557 - NLMS01 uses ER26500+ SPC1520 battery pack.See below linkfor detail information about the battery info and how to replace.481 +[[image:image-20220907171221-21.png]] 558 558 559 - [[**BatteryInfo&PowerConsumption Analyze**>>url:http://wiki.dragino.com/xwiki/bin/view/Main/How%20to%20calculate%20the%20battery%20life%20of%20Dragino%20sensors%3F/]].483 +=== 2.12.2 Power consumption Analyze === 560 560 485 +Dragino battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval. 561 561 562 - = 3. Access NB-IoTModule=487 +Instruction to use as below: 563 563 489 +**Step 1: **Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/]] 564 564 565 - UserscandirectlyaccesstheAT commandset of the NB-IoT module.491 +**Step 2: ** Open it and choose 566 566 567 -The AT Command set can refer the BC35-G NB-IoT Module AT Command: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/]] 493 +* Product Model 494 +* Uplink Interval 495 +* Working Mode 568 568 497 +And the Life expectation in difference case will be shown on the right. 569 569 570 -[[image:image-20220907171221-2 3.png]] 499 +[[image:image-20220907171221-22.jpeg]] 571 571 501 +=== 2.12.3 Battery Note === 572 572 573 - =4.Using theATCommands=503 +The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased. 574 574 575 -== 4.1AccessATCommands==505 +=== 2.12.4 Replace the battery === 576 576 507 +The default battery pack of NLMS01 includes a ER26500 plus super capacitor. If user can't find this pack locally, they can find ER26500 or equivalence without the SPC1520 capacitor, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes). 577 577 578 - Seethislinkfor detail: [[https:~~/~~/www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0>>url:https://www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0]]509 += 3. Access NB-IoT Module = 579 579 580 -AT +<CMD>?:Helpon<CMD>511 +Users can directly access the AT command set of the NB-IoT module. 581 581 582 -AT +<CMD>:Run<CMD>513 +The AT Command set can refer the BC35-G NB-IoT Module AT Command: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/]] 583 583 584 - AT+<CMD>=<value>:Set the value515 +[[image:image-20220907171221-23.png]] 585 585 586 - AT+<CMD>=?:Getthevalue517 += 4. Using the AT Commands = 587 587 519 +== 4.1 Access AT Commands == 588 588 589 - (%style="color:#037691" %)**GeneralCommands**521 +See this link for detail: [[https:~~/~~/www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0>>url:https://www.dropbox.com/sh/351dwor6joz8nwh/AADn1BQaAAxLF_QMyU8NkW47a?dl=0]] 590 590 591 -AT :Attention523 +AT+<CMD>? : Help on <CMD> 592 592 593 -AT ?:Short Help525 +AT+<CMD> : Run <CMD> 594 594 595 -AT Z:MCUReset527 +AT+<CMD>=<value> : Set the value 596 596 597 -AT+ TDC:ApplicationDataTransmissionInterval529 +AT+<CMD>=? : Get the value 598 598 599 - AT+CFG: Printallconfigurations531 +**General Commands** 600 600 601 -AT +CFGMOD:Workingmodeselection533 +AT : Attention 602 602 603 -AT +INTMOD:Setthetriggerinterruptmode535 +AT? : Short Help 604 604 605 -AT +5VT:Setextendthetimeof5Vpower537 +ATZ : MCU Reset 606 606 607 -AT+ PRO :Chooseagreement539 +AT+TDC : Application Data Transmission Interval 608 608 609 -AT+ RXDL:Extendthesendingandreceivingme541 +AT+CFG : Print all configurations 610 610 611 -AT+ SERVADDR:ServerAddress543 +AT+CFGMOD : Working mode selection 612 612 613 -AT+ APN :Getor set theAPN545 +AT+INTMOD : Set the trigger interrupt mode 614 614 615 -AT+ FBAND :GetorSetwhethertoautomaticallymodifythefrequencyband547 +AT+5VT : Set extend the time of 5V power 616 616 617 -AT+ DNSCFG:GetorSetDNSServer549 +AT+PRO : Choose agreement 618 618 619 -AT+ GETSENSORVALUEReturnsthecurrentsensormeasurement551 +AT+RXDL : Extend the sending and receiving time 620 620 621 -AT+ TR:Get orSetrecordtime"553 +AT+SERVADDR : Server Address 622 622 623 -AT+ NOUD:the numberfdatato beuploaded555 +AT+TR : Get or Set record time" 624 624 625 -AT+CDP : Read or Clear cached data 626 626 627 -AT+ TEMPALARM:alarm of temp558 +AT+NOUD : Get or Set the number of data to be uploaded 628 628 629 -AT+HUMALARM : Get or Set alarm of humidity 630 630 561 +AT+CDP : Read or Clear cached data 631 631 632 -(% style="color:#037691" %)**COAP Management** 633 633 634 -AT+ URI:Resourceparameters564 +AT+TEMPALARM : Get or Set alarm of temp 635 635 566 +AT+HUMALARM : Get or Set alarm of PH 636 636 637 -(% style="color:#037691" %)**UDP Management** 638 638 639 - AT+CFM: Upload confirmationmode(onlyvalid for UDP)569 +**COAP Management** 640 640 571 +AT+URI : Resource parameters 641 641 642 - (% style="color:#037691" %)**MQTTManagement**573 +**UDP Management** 643 643 644 -AT+C LIENT:GetorSetMQTTclient575 +AT+CFM : Upload confirmation mode (only valid for UDP) 645 645 646 - AT+UNAME : Get or Set MQTTUsername577 +**MQTT Management** 647 647 648 -AT+ PWDpassword579 +AT+CLIENT : Get or Set MQTT client 649 649 650 -AT+ PUBTOPIC:Get or Set MQTTpublish topic581 +AT+UNAME : Get or Set MQTT Username 651 651 652 -AT+ SUBTOPIC:ubscription topic583 +AT+PWD : Get or Set MQTT password 653 653 585 +AT+PUBTOPIC : Get or Set MQTT publish topic 654 654 655 - (%style="color:#037691"%)**Information**587 +AT+SUBTOPIC : Get or Set MQTT subscription topic 656 656 657 - AT+FDR : Factory DataReset589 +**Information** 658 658 659 -AT+ PWORD:SerialAccessPassword591 +AT+FDR : Factory Data Reset 660 660 593 +AT+PWORD : Serial Access Password 661 661 662 662 = 5. FAQ = 663 663 664 664 == 5.1 How to Upgrade Firmware == 665 665 666 - 667 667 User can upgrade the firmware for 1) bug fix, 2) new feature release. 668 668 669 669 Please see this link for how to upgrade: [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList]] 670 670 603 +**Notice, **NLMS01 **and **NLMS01 **share the same mother board. They use the same connection and method to update.** 671 671 672 -(% style="color:red" %)**Notice, NLMS01 and LLMS01 share the same mother board. They use the same connection and method to update.** 673 - 674 - 675 675 = 6. Trouble Shooting = 676 676 677 677 == 6.1 Connection problem when uploading firmware == 678 678 679 - 680 680 **Please see: **[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting]] 681 681 682 - 683 683 == 6.2 AT Command input doesn't work == 684 684 613 +In the case if user can see the console output but can't type input to the device. Please check if you already include the **ENTER** while sending out the command. Some serial tool doesn't send **ENTER** while press the send key, user need to add ENTER in their string. 685 685 686 -In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string. 687 - 688 - 689 689 = 7. Order Info = 690 690 691 - 692 692 Part Number**:** NLMS01 693 693 694 - 695 695 = 8. Packing Info = 696 696 621 +**Package Includes**: 697 697 698 -(% style="color:#037691" %)**Package Includes:** 699 - 700 700 * NLMS01 NB-IoT Leaf Moisture Sensor x 1 701 701 702 - (% style="color:#037691" %)**Dimension and weight**:625 +**Dimension and weight**: 703 703 704 704 * Device Size: cm 705 705 * Device Weight: g ... ... @@ -706,11 +706,8 @@ 706 706 * Package Size / pcs : cm 707 707 * Weight / pcs : g 708 708 709 - 710 - 711 711 = 9. Support = 712 712 713 - 714 714 * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule. 715 715 * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]] 716 716
- image-20220913090720-1.png
-
- Author
-
... ... @@ -1,1 +1,0 @@ 1 -XWiki.Xiaoling - Size
-
... ... @@ -1,1 +1,0 @@ 1 -224.9 KB - Content
- image-20221009001002-1.png
-
- Author
-
... ... @@ -1,1 +1,0 @@ 1 -XWiki.Edwin - Size
-
... ... @@ -1,1 +1,0 @@ 1 -282.9 KB - Content