Last modified by Bei Jinggeng on 2024/05/31 09:53
<
From version < 76.1 >
edited by Xiaoling
on 2022/07/09 09:03
To version < 60.1 >
edited by Xiaoling
on 2022/07/08 14:04
>
Change comment: Uploaded new attachment "image-20220708140453-6.png", version {1}

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -NDDS75 NB-IoT Distance Detect Sensor User Manual
1 +NSE01 - NB-IoT Soil Moisture & EC Sensor User Manual
Content
... ... @@ -1,11 +1,10 @@
1 1  (% style="text-align:center" %)
2 -[[image:image-20220709085040-1.png||height="542" width="524"]]
2 +[[image:image-20220606151504-2.jpeg||height="554" width="554"]]
3 3  
4 4  
5 5  
6 6  
7 7  
8 -**Table of Contents:**
9 9  
10 10  
11 11  
... ... @@ -12,23 +12,28 @@
12 12  
13 13  
14 14  
14 +**Table of Contents:**
15 15  
16 +
17 +
18 +
19 +
20 +
16 16  = 1.  Introduction =
17 17  
18 -== 1.1 ​ What is NDDS75 Distance Detection Sensor ==
23 +== 1.1 ​ What is LoRaWAN Soil Moisture & EC Sensor ==
19 19  
20 20  (((
21 21  
22 22  
23 -(((
24 -The Dragino NDDS75 is a (% style="color:blue" %)**NB-IoT Distance Detection Sensor**(%%) for Internet of Things solution. It is designed to measure the distance between the sensor and a flat object. The distance detection sensor is a module that uses ultrasonic sensing technology for distance measurement, and temperature compensation is performed internally to improve the reliability of data.
25 -\\The NDDS75 can be applied to scenarios such as horizontal distance measurement, liquid level measurement, parking management system, object proximity and presence detection, intelligent trash can management system, robot obstacle avoidance, automatic control, sewer, bottom water level monitoring, etc. It detects the distance between the measured object and the sensor, and uploads the value via wireless to IoT Server via NB-IoT Network.
26 -\\NarrowBand-Internet of Things (NB-IoT) is a standards-based low power wide area (LPWA) technology developed to enable a wide range of new IoT devices and services. NB-IoT significantly improves the power consumption of user devices, system capacity and spectrum efficiency, especially in deep coverage.
27 -\\NDDS75 supports different uplink methods include (% style="color:blue" %)**TCP, MQTT, UDP and CoAP** (%%)for different application requirement.
28 -\\NDDS75 is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), It is designed for long term use up to 5 years. (Actually Battery life depends on the use environment, update period & uplink method)
29 -\\To use NDDS75, user needs to check if there is NB-IoT coverage in local area and with the bands NDDS75 supports. If the local operate support it, user needs to get a NB-IoT SIM card from local operator and install NDDS75 to get NB-IoT network connection.
30 -)))
28 +Dragino NSE01 is an (% style="color:blue" %)**NB-IOT soil moisture & EC sensor**(%%) for agricultural IoT. Used to measure the soil moisture of saline-alkali soil and loam. The soil sensor uses the FDR method to calculate soil moisture and compensates it with soil temperature and electrical conductivity. It has also been calibrated for mineral soil types at the factory.
31 31  
30 +It can detect (% style="color:blue" %)**Soil Moisture, Soil Temperature and Soil Conductivity**(%%), and upload its value to the server wirelessly.
31 +
32 +The wireless technology used in NSE01 allows the device to send data at a low data rate and reach ultra-long distances, providing ultra-long-distance spread spectrum Communication.
33 +
34 +NSE01 are powered by (% style="color:blue" %)**8500mAh Li-SOCI2**(%%) batteries, which can be used for up to 5 years.  
35 +
32 32  
33 33  )))
34 34  
... ... @@ -35,28 +35,26 @@
35 35  [[image:1654503236291-817.png]]
36 36  
37 37  
38 -[[image:1657327959271-447.png]]
42 +[[image:1657245163077-232.png]]
39 39  
40 40  
41 41  
42 -== 1.2 ​ Features ==
46 +== 1.2 ​Features ==
43 43  
44 44  
45 45  * NB-IoT Bands: B1/B3/B8/B5/B20/B28 @H-FDD
46 -* Ultra low power consumption
47 -* Distance Detection by Ultrasonic technology
48 -* Flat object range 280mm - 7500mm
49 -* Accuracy: ±(1cm+S*0.3%) (S: Distance)
50 -* Cable Length: 25cm
50 +* Monitor Soil Moisture
51 +* Monitor Soil Temperature
52 +* Monitor Soil Conductivity
51 51  * AT Commands to change parameters
52 52  * Uplink on periodically
53 53  * Downlink to change configure
54 54  * IP66 Waterproof Enclosure
57 +* Ultra-Low Power consumption
58 +* AT Commands to change parameters
55 55  * Micro SIM card slot for NB-IoT SIM
56 56  * 8500mAh Battery for long term use
57 57  
58 -
59 -
60 60  == 1.3  Specification ==
61 61  
62 62  
... ... @@ -74,38 +74,21 @@
74 74  * - B20 @H-FDD: 800MHz
75 75  * - B28 @H-FDD: 700MHz
76 76  
79 +(% style="color:#037691" %)**Probe Specification:**
77 77  
78 -(% style="color:#037691" %)**Battery:**
81 +Measure Volume: Base on the centra pin of the probe, a cylinder with 7cm diameter and 10cm height.
79 79  
80 -* Li/SOCI2 un-chargeable battery
81 -* Capacity: 8500mAh
82 -* Self Discharge: <1% / Year @ 25°C
83 -* Max continuously current: 130mA
84 -* Max boost current: 2A, 1 second
83 +[[image:image-20220708101224-1.png]]
85 85  
86 86  
87 -(% style="color:#037691" %)**Power Consumption**
88 88  
89 -* STOP Mode: 10uA @ 3.3v
90 -* Max transmit power: 350mA@3.3v
91 -
92 -
93 -
94 -
95 95  == ​1.4  Applications ==
96 96  
97 -* Smart Buildings & Home Automation
98 -* Logistics and Supply Chain Management
99 -* Smart Metering
100 100  * Smart Agriculture
101 -* Smart Cities
102 -* Smart Factory
103 103  
104 104  (% class="wikigeneratedid" id="H200B1.5FirmwareChangelog" %)
105 105  ​
106 106  
107 -
108 -
109 109  == 1.5  Pin Definitions ==
110 110  
111 111  
... ... @@ -141,9 +141,7 @@
141 141  === 2.2.1 Test Requirement ===
142 142  
143 143  
144 -(((
145 145  To use NSE01 in your city, make sure meet below requirements:
146 -)))
147 147  
148 148  * Your local operator has already distributed a NB-IoT Network there.
149 149  * The local NB-IoT network used the band that NSE01 supports.
... ... @@ -160,13 +160,9 @@
160 160  
161 161  === 2.2.2 Insert SIM card ===
162 162  
163 -(((
164 164  Insert the NB-IoT Card get from your provider.
165 -)))
166 166  
167 -(((
168 168  User need to take out the NB-IoT module and insert the SIM card like below:
169 -)))
170 170  
171 171  
172 172  [[image:1657249468462-536.png]]
... ... @@ -205,9 +205,7 @@
205 205  
206 206  [[image:image-20220708110657-3.png]]
207 207  
208 -(((
209 209  (% style="color:red" %)Note: the valid AT Commands can be found at: (%%)[[http:~~/~~/www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/]]
210 -)))
211 211  
212 212  
213 213  
... ... @@ -310,14 +310,12 @@
310 310  In this mode, uplink payload includes in total 18 bytes
311 311  
312 312  (% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:510px" %)
313 -|=(% style="width: 60px;" %)(((
290 +|=(% style="width: 50px;" %)(((
314 314  **Size(bytes)**
315 -)))|=(% style="width: 50px;" %)**6**|=(% style="width: 25px;" %)2|=(% style="width: 25px;" %)**2**|=(% style="width: 70px;" %)**1**|=(% style="width: 60px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 90px;" %)**2**|=(% style="width: 50px;" %)**1**
316 -|(% style="width:97px" %)**Value**|(% style="width:83px" %)[[Device ID>>||anchor="H2.4.1A0A0DeviceID"]]|(% style="width:41px" %)[[Ver>>||anchor="H2.4.2A0VersionInfo"]]|(% style="width:46px" %)[[BAT>>||anchor="H2.4.3A0BatteryInfo"]]|(% style="width:123px" %)[[Signal Strength>>||anchor="H2.4.4A0SignalStrength"]]|(% style="width:108px" %)[[Soil Moisture>>||anchor="H2.4.5A0SoilMoisture"]]|(% style="width:133px" %)[[Soil Temperature>>||anchor="H2.4.6A0SoilTemperature"]]|(% style="width:159px" %)[[Soil Conductivity(EC)>>||anchor="H2.4.7A0SoilConductivity28EC29"]]|(% style="width:80px" %)[[Interrupt>>||anchor="H2.4.8A0DigitalInterrupt"]]
292 +)))|=(% style="width: 50px;" %)**6**|=(% style="width: 25px;" %)2|=(% style="width: 25px;" %)**2**|=(% style="width: 80px;" %)**1**|=(% style="width: 80px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 40px;" %)**1**
293 +|(% style="width:97px" %)**Value**|(% style="width:83px" %)[[Device ID>>||anchor="H"]]|(% style="width:41px" %)[[Ver>>||anchor="H"]]|(% style="width:46px" %)[[BAT>>||anchor="H"]]|(% style="width:123px" %)[[Signal Strength>>||anchor="H"]]|(% style="width:108px" %)[[Soil Moisture>>||anchor="H"]]|(% style="width:133px" %)[[Soil Temperature>>||anchor="H"]]|(% style="width:159px" %)[[Soil Conductivity(EC)>>||anchor="H"]]|(% style="width:80px" %)[[Interrupt>>||anchor="H"]]
317 317  
318 -(((
319 319  If we use the MQTT client to subscribe to this MQTT topic, we can see the following information when the NSE01 uplink data.
320 -)))
321 321  
322 322  
323 323  [[image:image-20220708111918-4.png]]
... ... @@ -337,42 +337,29 @@
337 337  * Soil Conductivity(EC) = 0x02f9 =761 uS /cm
338 338  * Interrupt: 0x00 = 0
339 339  
315 +
340 340  == 2.4  Payload Explanation and Sensor Interface ==
341 341  
342 342  
343 343  === 2.4.1  Device ID ===
344 344  
345 -(((
346 346  By default, the Device ID equal to the last 6 bytes of IMEI.
347 -)))
348 348  
349 -(((
350 350  User can use (% style="color:blue" %)**AT+DEUI**(%%) to set Device ID
351 -)))
352 352  
353 -(((
354 354  **Example:**
355 -)))
356 356  
357 -(((
358 358  AT+DEUI=A84041F15612
359 -)))
360 360  
361 -(((
362 362  The Device ID is stored in a none-erase area, Upgrade the firmware or run AT+FDR won't erase Device ID.
363 -)))
364 364  
365 365  
366 366  
367 367  === 2.4.2  Version Info ===
368 368  
369 -(((
370 370  Specify the software version: 0x64=100, means firmware version 1.00.
371 -)))
372 372  
373 -(((
374 374  For example: 0x00 64 : this device is NSE01 with firmware version 1.0.0.
375 -)))
376 376  
377 377  
378 378  
... ... @@ -394,33 +394,19 @@
394 394  
395 395  === 2.4.4  Signal Strength ===
396 396  
397 -(((
398 398  NB-IoT Network signal Strength.
399 -)))
400 400  
401 -(((
402 402  **Ex1: 0x1d = 29**
403 -)))
404 404  
405 -(((
406 406  (% style="color:blue" %)**0**(%%)  -113dBm or less
407 -)))
408 408  
409 -(((
410 410  (% style="color:blue" %)**1**(%%)  -111dBm
411 -)))
412 412  
413 -(((
414 414  (% style="color:blue" %)**2...30**(%%) -109dBm... -53dBm
415 -)))
416 416  
417 -(((
418 418  (% style="color:blue" %)**31**  (%%) -51dBm or greater
419 -)))
420 420  
421 -(((
422 422  (% style="color:blue" %)**99**   (%%) Not known or not detectable
423 -)))
424 424  
425 425  
426 426  
... ... @@ -427,16 +427,12 @@
427 427  === 2.4.5  Soil Moisture ===
428 428  
429 429  (((
430 -(((
431 431  Get the moisture content of the soil. The value range of the register is 0-10000(Decimal), divide this value by 100 to get the percentage of moisture in the soil.
432 432  )))
433 -)))
434 434  
435 435  (((
436 -(((
437 437  For example, if the data you get from the register is **__0x05 0xDC__**, the moisture content in the soil is
438 438  )))
439 -)))
440 440  
441 441  (((
442 442  
... ... @@ -451,7 +451,7 @@
451 451  === 2.4.6  Soil Temperature ===
452 452  
453 453  (((
454 -Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is __**0x09 0xEC**__, the temperature content in the soil is
398 + Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is __**0x09 0xEC**__, the temperature content in the soil is
455 455  )))
456 456  
457 457  (((
... ... @@ -492,66 +492,45 @@
492 492  
493 493  === 2.4.8  Digital Interrupt ===
494 494  
495 -(((
496 496  Digital Interrupt refers to pin (% style="color:blue" %)**GPIO_EXTI**(%%), and there are different trigger methods. When there is a trigger, the NSE01 will send a packet to the server.
497 -)))
498 498  
499 -(((
500 500  The command is:
501 -)))
502 502  
503 -(((
504 504  (% style="color:blue" %)**AT+INTMOD=3 **(%%) ~/~/(more info about INMOD please refer [[**AT Command Manual**>>url:https://www.dragino.com/downloads/downloads/NB-IoT/NBSN95/DRAGINO_NBSN95-NB_AT%20Commands_v1.1.0.pdf]])**.**
505 -)))
506 506  
507 507  
508 -(((
509 -The lower four bits of this data field shows if this packet is generated by interrupt or not. Click here for the hardware and software set up.
510 -)))
446 +The lower four bits of this data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H"]] for the hardware and software set up.
511 511  
512 512  
513 -(((
514 514  Example:
515 -)))
516 516  
517 -(((
518 518  0x(00): Normal uplink packet.
519 -)))
520 520  
521 -(((
522 522  0x(01): Interrupt Uplink Packet.
523 -)))
524 524  
525 525  
526 526  
527 527  === 2.4.9  ​+5V Output ===
528 528  
529 -(((
530 530  NSE01 will enable +5V output before all sampling and disable the +5v after all sampling. 
531 -)))
532 532  
533 533  
534 -(((
535 535  The 5V output time can be controlled by AT Command.
536 -)))
537 537  
538 -(((
539 539  (% style="color:blue" %)**AT+5VT=1000**
540 -)))
541 541  
542 -(((
543 543  Means set 5V valid time to have 1000ms. So the real 5V output will actually have 1000ms + sampling time for other sensors.
544 -)))
545 545  
546 546  
547 547  
548 548  == 2.5  Downlink Payload ==
549 549  
550 -By default, NSE01 prints the downlink payload to console port.
472 +By default, LSE50 prints the downlink payload to console port.
551 551  
552 552  [[image:image-20220708133731-5.png]]
553 553  
554 554  
477 +
555 555  (((
556 556  (% style="color:blue" %)**Examples:**
557 557  )))
... ... @@ -565,7 +565,7 @@
565 565  )))
566 566  
567 567  (((
568 -If the payload=0100003C, it means set the END Node's TDC to 0x00003C=60(S), while type code is 01.
491 +If the payload=0100003C, it means set the END Node’s TDC to 0x00003C=60(S), while type code is 01.
569 569  )))
570 570  
571 571  (((
... ... @@ -585,144 +585,432 @@
585 585  )))
586 586  
587 587  (((
588 -If payload = 0x04FF, it will reset the NSE01
511 +If payload = 0x04FF, it will reset the LSE01
589 589  )))
590 590  
591 591  
592 -* (% style="color:blue" %)**INTMOD**
515 +* (% style="color:blue" %)**CFM**
593 593  
594 -(((
595 -Downlink Payload: 06000003, Set AT+INTMOD=3
596 -)))
517 +Downlink Payload: 05000001, Set AT+CFM=1 or 05000000 , set AT+CFM=0
597 597  
598 598  
599 599  
600 -== 2.6  ​LED Indicator ==
521 +== 2.6 ​Show Data in DataCake IoT Server ==
601 601  
602 602  (((
603 -The NSE01 has an internal LED which is to show the status of different state.
524 +[[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:
525 +)))
604 604  
527 +(((
528 +
529 +)))
605 605  
606 -* When power on, NSE01 will detect if sensor probe is connected, if probe detected, LED will blink four times. (no blinks in this step is no probe)
607 -* Then the LED will be on for 1 second means device is boot normally.
608 -* After NSE01 join NB-IoT network. The LED will be ON for 3 seconds.
609 -* For each uplink probe, LED will be on for 500ms.
531 +(((
532 +(% style="color:blue" %)**Step 1**(%%):  Be sure that your device is programmed and properly connected to the network at this time.
610 610  )))
611 611  
535 +(((
536 +(% style="color:blue" %)**Step 2**(%%):  To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:
537 +)))
612 612  
613 613  
540 +[[image:1654505857935-743.png]]
614 614  
615 -== 2.7  Installation in Soil ==
616 616  
617 -__**Measurement the soil surface**__
543 +[[image:1654505874829-548.png]]
618 618  
619 -(((
620 -Choose the proper measuring position. Avoid the probe to touch rocks or hard things. Split the surface soil according to the measured deep. Keep the measured as original density. Vertical insert the probe into the soil to be measured. Make sure not shake when inserting. [[https:~~/~~/img.alicdn.com/imgextra/i3/2005165265/O1CN010rj9Oh1olPsQxrdUK_!!2005165265.jpg>>url:https://img.alicdn.com/imgextra/i3/2005165265/O1CN010rj9Oh1olPsQxrdUK_!!2005165265.jpg]]
621 -)))
622 622  
623 -[[image:1657259653666-883.png]] ​
546 +(% style="color:blue" %)**Step 3**(%%)**:**  Create an account or log in Datacake.
624 624  
548 +(% style="color:blue" %)**Step 4**(%%)**:**  Search the LSE01 and add DevEUI.
625 625  
626 -(((
627 -
628 628  
629 -(((
630 -Dig a hole with diameter > 20CM.
631 -)))
551 +[[image:1654505905236-553.png]]
632 632  
633 -(((
634 -Horizontal insert the probe to the soil and fill the hole for long term measurement.
635 -)))
636 -)))
637 637  
638 -[[image:1654506665940-119.png]]
554 +After added, the sensor data arrive TTN, it will also arrive and show in Mydevices.
639 639  
640 -(((
641 -
642 -)))
556 +[[image:1654505925508-181.png]]
643 643  
644 644  
645 -== 2.8  ​Firmware Change Log ==
646 646  
560 +== 2.7 Frequency Plans ==
647 647  
648 -Download URL & Firmware Change log
562 +The LSE01 uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
649 649  
650 -[[www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/Firmware/]]
651 651  
565 +=== 2.7.1 EU863-870 (EU868) ===
652 652  
653 -Upgrade Instruction: [[Upgrade_Firmware>>||anchor="H5.1200BHowtoUpgradeFirmware"]]
567 +(% style="color:#037691" %)** Uplink:**
654 654  
569 +868.1 - SF7BW125 to SF12BW125
655 655  
571 +868.3 - SF7BW125 to SF12BW125 and SF7BW250
656 656  
657 -== 2.9  ​Battery Analysis ==
573 +868.5 - SF7BW125 to SF12BW125
658 658  
659 -=== 2.9.1  ​Battery Type ===
575 +867.1 - SF7BW125 to SF12BW125
660 660  
577 +867.3 - SF7BW125 to SF12BW125
661 661  
579 +867.5 - SF7BW125 to SF12BW125
580 +
581 +867.7 - SF7BW125 to SF12BW125
582 +
583 +867.9 - SF7BW125 to SF12BW125
584 +
585 +868.8 - FSK
586 +
587 +
588 +(% style="color:#037691" %)** Downlink:**
589 +
590 +Uplink channels 1-9 (RX1)
591 +
592 +869.525 - SF9BW125 (RX2 downlink only)
593 +
594 +
595 +
596 +=== 2.7.2 US902-928(US915) ===
597 +
598 +Used in USA, Canada and South America. Default use CHE=2
599 +
600 +(% style="color:#037691" %)**Uplink:**
601 +
602 +903.9 - SF7BW125 to SF10BW125
603 +
604 +904.1 - SF7BW125 to SF10BW125
605 +
606 +904.3 - SF7BW125 to SF10BW125
607 +
608 +904.5 - SF7BW125 to SF10BW125
609 +
610 +904.7 - SF7BW125 to SF10BW125
611 +
612 +904.9 - SF7BW125 to SF10BW125
613 +
614 +905.1 - SF7BW125 to SF10BW125
615 +
616 +905.3 - SF7BW125 to SF10BW125
617 +
618 +
619 +(% style="color:#037691" %)**Downlink:**
620 +
621 +923.3 - SF7BW500 to SF12BW500
622 +
623 +923.9 - SF7BW500 to SF12BW500
624 +
625 +924.5 - SF7BW500 to SF12BW500
626 +
627 +925.1 - SF7BW500 to SF12BW500
628 +
629 +925.7 - SF7BW500 to SF12BW500
630 +
631 +926.3 - SF7BW500 to SF12BW500
632 +
633 +926.9 - SF7BW500 to SF12BW500
634 +
635 +927.5 - SF7BW500 to SF12BW500
636 +
637 +923.3 - SF12BW500(RX2 downlink only)
638 +
639 +
640 +
641 +=== 2.7.3 CN470-510 (CN470) ===
642 +
643 +Used in China, Default use CHE=1
644 +
645 +(% style="color:#037691" %)**Uplink:**
646 +
647 +486.3 - SF7BW125 to SF12BW125
648 +
649 +486.5 - SF7BW125 to SF12BW125
650 +
651 +486.7 - SF7BW125 to SF12BW125
652 +
653 +486.9 - SF7BW125 to SF12BW125
654 +
655 +487.1 - SF7BW125 to SF12BW125
656 +
657 +487.3 - SF7BW125 to SF12BW125
658 +
659 +487.5 - SF7BW125 to SF12BW125
660 +
661 +487.7 - SF7BW125 to SF12BW125
662 +
663 +
664 +(% style="color:#037691" %)**Downlink:**
665 +
666 +506.7 - SF7BW125 to SF12BW125
667 +
668 +506.9 - SF7BW125 to SF12BW125
669 +
670 +507.1 - SF7BW125 to SF12BW125
671 +
672 +507.3 - SF7BW125 to SF12BW125
673 +
674 +507.5 - SF7BW125 to SF12BW125
675 +
676 +507.7 - SF7BW125 to SF12BW125
677 +
678 +507.9 - SF7BW125 to SF12BW125
679 +
680 +508.1 - SF7BW125 to SF12BW125
681 +
682 +505.3 - SF12BW125 (RX2 downlink only)
683 +
684 +
685 +
686 +=== 2.7.4 AU915-928(AU915) ===
687 +
688 +Default use CHE=2
689 +
690 +(% style="color:#037691" %)**Uplink:**
691 +
692 +916.8 - SF7BW125 to SF12BW125
693 +
694 +917.0 - SF7BW125 to SF12BW125
695 +
696 +917.2 - SF7BW125 to SF12BW125
697 +
698 +917.4 - SF7BW125 to SF12BW125
699 +
700 +917.6 - SF7BW125 to SF12BW125
701 +
702 +917.8 - SF7BW125 to SF12BW125
703 +
704 +918.0 - SF7BW125 to SF12BW125
705 +
706 +918.2 - SF7BW125 to SF12BW125
707 +
708 +
709 +(% style="color:#037691" %)**Downlink:**
710 +
711 +923.3 - SF7BW500 to SF12BW500
712 +
713 +923.9 - SF7BW500 to SF12BW500
714 +
715 +924.5 - SF7BW500 to SF12BW500
716 +
717 +925.1 - SF7BW500 to SF12BW500
718 +
719 +925.7 - SF7BW500 to SF12BW500
720 +
721 +926.3 - SF7BW500 to SF12BW500
722 +
723 +926.9 - SF7BW500 to SF12BW500
724 +
725 +927.5 - SF7BW500 to SF12BW500
726 +
727 +923.3 - SF12BW500(RX2 downlink only)
728 +
729 +
730 +
731 +=== 2.7.5 AS920-923 & AS923-925 (AS923) ===
732 +
733 +(% style="color:#037691" %)**Default Uplink channel:**
734 +
735 +923.2 - SF7BW125 to SF10BW125
736 +
737 +923.4 - SF7BW125 to SF10BW125
738 +
739 +
740 +(% style="color:#037691" %)**Additional Uplink Channel**:
741 +
742 +(OTAA mode, channel added by JoinAccept message)
743 +
744 +(% style="color:#037691" %)**AS920~~AS923 for Japan, Malaysia, Singapore**:
745 +
746 +922.2 - SF7BW125 to SF10BW125
747 +
748 +922.4 - SF7BW125 to SF10BW125
749 +
750 +922.6 - SF7BW125 to SF10BW125
751 +
752 +922.8 - SF7BW125 to SF10BW125
753 +
754 +923.0 - SF7BW125 to SF10BW125
755 +
756 +922.0 - SF7BW125 to SF10BW125
757 +
758 +
759 +(% style="color:#037691" %)**AS923 ~~ AS925 for Brunei, Cambodia, Hong Kong, Indonesia, Laos, Taiwan, Thailand, Vietnam**:
760 +
761 +923.6 - SF7BW125 to SF10BW125
762 +
763 +923.8 - SF7BW125 to SF10BW125
764 +
765 +924.0 - SF7BW125 to SF10BW125
766 +
767 +924.2 - SF7BW125 to SF10BW125
768 +
769 +924.4 - SF7BW125 to SF10BW125
770 +
771 +924.6 - SF7BW125 to SF10BW125
772 +
773 +
774 +(% style="color:#037691" %)** Downlink:**
775 +
776 +Uplink channels 1-8 (RX1)
777 +
778 +923.2 - SF10BW125 (RX2)
779 +
780 +
781 +
782 +=== 2.7.6 KR920-923 (KR920) ===
783 +
784 +Default channel:
785 +
786 +922.1 - SF7BW125 to SF12BW125
787 +
788 +922.3 - SF7BW125 to SF12BW125
789 +
790 +922.5 - SF7BW125 to SF12BW125
791 +
792 +
793 +(% style="color:#037691" %)**Uplink: (OTAA mode, channel added by JoinAccept message)**
794 +
795 +922.1 - SF7BW125 to SF12BW125
796 +
797 +922.3 - SF7BW125 to SF12BW125
798 +
799 +922.5 - SF7BW125 to SF12BW125
800 +
801 +922.7 - SF7BW125 to SF12BW125
802 +
803 +922.9 - SF7BW125 to SF12BW125
804 +
805 +923.1 - SF7BW125 to SF12BW125
806 +
807 +923.3 - SF7BW125 to SF12BW125
808 +
809 +
810 +(% style="color:#037691" %)**Downlink:**
811 +
812 +Uplink channels 1-7(RX1)
813 +
814 +921.9 - SF12BW125 (RX2 downlink only; SF12BW125 might be changed to SF9BW125)
815 +
816 +
817 +
818 +=== 2.7.7 IN865-867 (IN865) ===
819 +
820 +(% style="color:#037691" %)** Uplink:**
821 +
822 +865.0625 - SF7BW125 to SF12BW125
823 +
824 +865.4025 - SF7BW125 to SF12BW125
825 +
826 +865.9850 - SF7BW125 to SF12BW125
827 +
828 +
829 +(% style="color:#037691" %) **Downlink:**
830 +
831 +Uplink channels 1-3 (RX1)
832 +
833 +866.550 - SF10BW125 (RX2)
834 +
835 +
836 +
837 +
838 +== 2.8 LED Indicator ==
839 +
840 +The LSE01 has an internal LED which is to show the status of different state.
841 +
842 +* Blink once when device power on.
843 +* Solid ON for 5 seconds once device successful Join the network.
844 +* Blink once when device transmit a packet.
845 +
846 +== 2.9 Installation in Soil ==
847 +
848 +**Measurement the soil surface**
849 +
850 +
851 +[[image:1654506634463-199.png]] ​
852 +
662 662  (((
663 -The NSE01 battery is a combination of an 8500mAh Li/SOCI2 Battery and a Super Capacitor. The battery is none-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
854 +(((
855 +Choose the proper measuring position. Avoid the probe to touch rocks or hard things. Split the surface soil according to the measured deep. Keep the measured as original density. Vertical insert the probe into the soil to be measured. Make sure not shake when inserting.
664 664  )))
857 +)))
665 665  
666 666  
860 +
861 +[[image:1654506665940-119.png]]
862 +
667 667  (((
668 -The battery is designed to last for several years depends on the actually use environment and update interval. 
864 +Dig a hole with diameter > 20CM.
669 669  )))
670 670  
867 +(((
868 +Horizontal insert the probe to the soil and fill the hole for long term measurement.
869 +)))
671 671  
871 +
872 +== 2.10 ​Firmware Change Log ==
873 +
672 672  (((
673 -The battery related documents as below:
875 +**Firmware download link:**
674 674  )))
675 675  
676 -* [[Battery Dimension>>http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
677 -* [[Lithium-Thionyl Chloride Battery datasheet>>http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
678 -* [[Lithium-ion Battery-Capacitor datasheet>>http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
878 +(((
879 +[[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/]]
880 +)))
679 679  
680 680  (((
681 -[[image:image-20220708140453-6.png]]
883 +
682 682  )))
683 683  
886 +(((
887 +**Firmware Upgrade Method: **[[Firmware Upgrade Instruction>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome]]
888 +)))
684 684  
890 +(((
891 +
892 +)))
685 685  
686 -=== 2.9.2  Power consumption Analyze ===
894 +(((
895 +**V1.0.**
896 +)))
687 687  
688 688  (((
689 -Dragino battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
899 +Release
690 690  )))
691 691  
692 692  
903 +== 2.11 ​Battery Analysis ==
904 +
905 +=== 2.11.1 ​Battery Type ===
906 +
693 693  (((
694 -Instruction to use as below:
908 +The LSE01 battery is a combination of a 4000mAh Li/SOCI2 Battery and a Super Capacitor. The battery is non-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
695 695  )))
696 696  
697 697  (((
698 -(% style="color:blue" %)**Step 1:  **(%%)Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/]]
912 +The battery is designed to last for more than 5 years for the LSN50.
699 699  )))
700 700  
701 -
702 702  (((
703 -(% style="color:blue" %)**Step 2: **(%%) Open it and choose
916 +(((
917 +The battery-related documents are as below:
704 704  )))
919 +)))
705 705  
706 706  * (((
707 -Product Model
922 +[[Battery Dimension>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/]],
708 708  )))
709 709  * (((
710 -Uplink Interval
925 +[[Lithium-Thionyl Chloride Battery  datasheet>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/]],
711 711  )))
712 712  * (((
713 -Working Mode
928 +[[Lithium-ion Battery-Capacitor datasheet>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/]], [[Tech Spec>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/]]
714 714  )))
715 715  
716 -(((
717 -And the Life expectation in difference case will be shown on the right.
718 -)))
931 + [[image:image-20220610172436-1.png]]
719 719  
720 -[[image:image-20220708141352-7.jpeg]]
721 721  
722 722  
935 +=== 2.11.2 ​Battery Note ===
723 723  
724 -=== 2.9.3  ​Battery Note ===
725 -
726 726  (((
727 727  The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
728 728  )))
... ... @@ -729,176 +729,302 @@
729 729  
730 730  
731 731  
732 -=== 2.9.4  Replace the battery ===
943 +=== 2.11.3 Replace the battery ===
733 733  
734 734  (((
735 -The default battery pack of NSE01 includes a ER26500 plus super capacitor. If user can't find this pack locally, they can find ER26500 or equivalence without the SPC1520 capacitor, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes).
946 +If Battery is lower than 2.7v, user should replace the battery of LSE01.
736 736  )))
737 737  
738 -
739 -
740 -= 3. ​ Access NB-IoT Module =
741 -
742 742  (((
743 -Users can directly access the AT command set of the NB-IoT module.
950 +You can change the battery in the LSE01.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
744 744  )))
745 745  
746 746  (((
747 -The AT Command set can refer the BC35-G NB-IoT Module AT Command: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/]] 
954 +The default battery pack of LSE01 includes a ER18505 plus super capacitor. If user can’t find this pack locally, they can find ER18505 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
748 748  )))
749 749  
750 -[[image:1657261278785-153.png]]
751 751  
752 752  
959 += 3. ​Using the AT Commands =
753 753  
754 -= 4.  Using the AT Commands =
961 +== 3.1 Access AT Commands ==
755 755  
756 -== 4.1  Access AT Commands ==
757 757  
758 -See this link for detail: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/]]
964 +LSE01 supports AT Command set in the stock firmware. You can use a USB to TTL adapter to connect to LSE01 for using AT command, as below.
759 759  
966 +[[image:1654501986557-872.png||height="391" width="800"]]
760 760  
761 -AT+<CMD>?  : Help on <CMD>
762 762  
763 -AT+<CMD>         : Run <CMD>
969 +Or if you have below board, use below connection:
764 764  
765 -AT+<CMD>=<value> : Set the value
766 766  
767 -AT+<CMD>=?  : Get the value
972 +[[image:1654502005655-729.png||height="503" width="801"]]
768 768  
769 769  
975 +
976 +In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LSE01. LSE01 will output system info once power on as below:
977 +
978 +
979 + [[image:1654502050864-459.png||height="564" width="806"]]
980 +
981 +
982 +Below are the available commands, a more detailed AT Command manual can be found at [[AT Command Manual>>https://www.dropbox.com/sh/qr6vproz4z4kzjz/AAAD48h3OyWrU1hq_Cqm8jIwa?dl=0]]: [[https:~~/~~/www.dropbox.com/sh/qr6vproz4z4kzjz/AAAD48h3OyWrU1hq_Cqm8jIwa?dl=0>>https://www.dropbox.com/sh/qr6vproz4z4kzjz/AAAD48h3OyWrU1hq_Cqm8jIwa?dl=0]]
983 +
984 +
985 +(% style="background-color:#dcdcdc" %)**AT+<CMD>=?AT+<CMD>? **(%%) : Help on <CMD>
986 +
987 +(% style="background-color:#dcdcdc" %)**AT+<CMD>=?AT+<CMD> **(%%) : Run <CMD>
988 +
989 +(% style="background-color:#dcdcdc" %)**AT+<CMD>=?AT+<CMD>=<value>**(%%) : Set the value
990 +
991 +(% style="background-color:#dcdcdc" %)**AT+<CMD>=?AT+<CMD>=?**(%%)  : Get the value
992 +
993 +
770 770  (% style="color:#037691" %)**General Commands**(%%)      
771 771  
772 -AT  : Attention       
996 +(% style="background-color:#dcdcdc" %)**AT**(%%)  : Attention       
773 773  
774 -AT?  : Short Help     
998 +(% style="background-color:#dcdcdc" %)**AT?**(%%)  : Short Help     
775 775  
776 -ATZ  : MCU Reset    
1000 +(% style="background-color:#dcdcdc" %)**ATZ**(%%)  : MCU Reset    
777 777  
778 -AT+TDC  : Application Data Transmission Interval
1002 +(% style="background-color:#dcdcdc" %)**AT+TDC**(%%)  : Application Data Transmission Interval 
779 779  
780 -AT+CFG  : Print all configurations
781 781  
782 -AT+CFGMOD           : Working mode selection
1005 +(% style="color:#037691" %)**Keys, IDs and EUIs management**
783 783  
784 -AT+INTMOD            : Set the trigger interrupt mode
1007 +(% style="background-color:#dcdcdc" %)**AT+APPEUI**(%%)              : Application EUI      
785 785  
786 -AT+5VT  : Set extend the time of 5V power  
1009 +(% style="background-color:#dcdcdc" %)**AT+APPKEY**(%%)              : Application Key     
787 787  
788 -AT+PRO  : Choose agreement
1011 +(% style="background-color:#dcdcdc" %)**AT+APPSKEY**(%%)            : Application Session Key
789 789  
790 -AT+WEIGRE  : Get weight or set weight to 0
1013 +(% style="background-color:#dcdcdc" %)**AT+DADDR**(%%)              : Device Address     
791 791  
792 -AT+WEIGAP  : Get or Set the GapValue of weight
1015 +(% style="background-color:#dcdcdc" %)**AT+DEUI**(%%)                   : Device EUI     
793 793  
794 -AT+RXDL  : Extend the sending and receiving time
1017 +(% style="background-color:#dcdcdc" %)**AT+NWKID**(%%)               : Network ID (You can enter this command change only after successful network connection) 
795 795  
796 -AT+CNTFAC  : Get or set counting parameters
1019 +(% style="background-color:#dcdcdc" %)**AT+NWKSKEY**(%%)          : Network Session Key Joining and sending date on LoRa network  
797 797  
798 -AT+SERVADDR  : Server Address
1021 +(% style="background-color:#dcdcdc" %)**AT+CFM**(%%)  : Confirm Mode       
799 799  
1023 +(% style="background-color:#dcdcdc" %)**AT+CFS**(%%)                     : Confirm Status       
800 800  
801 -(% style="color:#037691" %)**COAP Management**      
1025 +(% style="background-color:#dcdcdc" %)**AT+JOIN**(%%)  : Join LoRa? Network       
802 802  
803 -AT+URI            : Resource parameters
1027 +(% style="background-color:#dcdcdc" %)**AT+NJM**(%%)  : LoRa? Network Join Mode    
804 804  
1029 +(% style="background-color:#dcdcdc" %)**AT+NJS**(%%)                     : LoRa? Network Join Status    
805 805  
806 -(% style="color:#037691" %)**UDP Management**
1031 +(% style="background-color:#dcdcdc" %)**AT+RECV**(%%)                  : Print Last Received Data in Raw Format
807 807  
808 -AT+CFM          : Upload confirmation mode (only valid for UDP)
1033 +(% style="background-color:#dcdcdc" %)**AT+RECVB**(%%)                : Print Last Received Data in Binary Format      
809 809  
1035 +(% style="background-color:#dcdcdc" %)**AT+SEND**(%%)                  : Send Text Data      
810 810  
811 -(% style="color:#037691" %)**MQTT Management**
1037 +(% style="background-color:#dcdcdc" %)**AT+SENB**(%%)                  : Send Hexadecimal Data
812 812  
813 -AT+CLIENT               : Get or Set MQTT client
814 814  
815 -AT+UNAME  : Get or Set MQTT Username
1040 +(% style="color:#037691" %)**LoRa Network Management**
816 816  
817 -AT+PWD                  : Get or Set MQTT password
1042 +(% style="background-color:#dcdcdc" %)**AT+ADR**(%%)          : Adaptive Rate
818 818  
819 -AT+PUBTOPIC  : Get or Set MQTT publish topic
1044 +(% style="background-color:#dcdcdc" %)**AT+CLASS**(%%)  : LoRa Class(Currently only support class A
820 820  
821 -AT+SUBTOPIC  : Get or Set MQTT subscription topic
1046 +(% style="background-color:#dcdcdc" %)**AT+DCS**(%%)  : Duty Cycle Setting 
822 822  
1048 +(% style="background-color:#dcdcdc" %)**AT+DR**(%%)  : Data Rate (Can Only be Modified after ADR=0)     
823 823  
824 -(% style="color:#037691" %)**Information**          
1050 +(% style="background-color:#dcdcdc" %)**AT+FCD**(%%)  : Frame Counter Downlink       
825 825  
826 -AT+FDR  : Factory Data Reset
1052 +(% style="background-color:#dcdcdc" %)**AT+FCU**(%%)  : Frame Counter Uplink   
827 827  
828 -AT+PWORD  : Serial Access Password
1054 +(% style="background-color:#dcdcdc" %)**AT+JN1DL**(%%)  : Join Accept Delay1
829 829  
1056 +(% style="background-color:#dcdcdc" %)**AT+JN2DL**(%%)  : Join Accept Delay2
830 830  
1058 +(% style="background-color:#dcdcdc" %)**AT+PNM**(%%)  : Public Network Mode   
831 831  
832 -= ​5.  FAQ =
1060 +(% style="background-color:#dcdcdc" %)**AT+RX1DL**(%%)  : Receive Delay1      
833 833  
834 -== 5.1 ​ How to Upgrade Firmware ==
1062 +(% style="background-color:#dcdcdc" %)**AT+RX2DL**(%%)  : Receive Delay2      
835 835  
1064 +(% style="background-color:#dcdcdc" %)**AT+RX2DR**(%%)  : Rx2 Window Data Rate 
836 836  
1066 +(% style="background-color:#dcdcdc" %)**AT+RX2FQ**(%%)  : Rx2 Window Frequency
1067 +
1068 +(% style="background-color:#dcdcdc" %)**AT+TXP**(%%)  : Transmit Power
1069 +
1070 +(% style="background-color:#dcdcdc" %)**AT+ MOD**(%%)  : Set work mode
1071 +
1072 +
1073 +(% style="color:#037691" %)**Information** 
1074 +
1075 +(% style="background-color:#dcdcdc" %)**AT+RSSI**(%%)           : RSSI of the Last Received Packet   
1076 +
1077 +(% style="background-color:#dcdcdc" %)**AT+SNR**(%%)           : SNR of the Last Received Packet   
1078 +
1079 +(% style="background-color:#dcdcdc" %)**AT+VER**(%%)           : Image Version and Frequency Band       
1080 +
1081 +(% style="background-color:#dcdcdc" %)**AT+FDR**(%%)           : Factory Data Reset
1082 +
1083 +(% style="background-color:#dcdcdc" %)**AT+PORT**(%%)  : Application Port    
1084 +
1085 +(% style="background-color:#dcdcdc" %)**AT+CHS**(%%)  : Get or Set Frequency (Unit: Hz) for Single Channel Mode
1086 +
1087 + (% style="background-color:#dcdcdc" %)**AT+CHE**(%%)  : Get or Set eight channels mode, Only for US915, AU915, CN470
1088 +
1089 +
1090 += ​4. FAQ =
1091 +
1092 +== 4.1 ​How to change the LoRa Frequency Bands/Region? ==
1093 +
837 837  (((
838 -User can upgrade the firmware for 1) bug fix, 2) new feature release.
1095 +You can follow the instructions for [[how to upgrade image>>||anchor="H2.10200BFirmwareChangeLog"]].
1096 +When downloading the images, choose the required image file for download. ​
839 839  )))
840 840  
841 841  (((
842 -Please see this link for how to upgrade:  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList>>http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList]]
1100 +
843 843  )))
844 844  
845 845  (((
846 -(% style="color:red" %)Notice, NSE01 and LSE01 share the same mother board. They use the same connection and method to update.
1104 +How to set up LSE01 to work in 8 channel mode By default, the frequency bands US915, AU915, CN470 work in 72 frequencies. Many gateways are 8 channel gateways, and in this case, the OTAA join time and uplink schedule is long and unpredictable while the end node is hopping in 72 frequencies.
847 847  )))
848 848  
1107 +(((
1108 +
1109 +)))
849 849  
1111 +(((
1112 +You can configure the end node to work in 8 channel mode by using the AT+CHE command. The 500kHz channels are always included for OTAA.
1113 +)))
850 850  
851 -== 5.2  Can I calibrate NSE01 to different soil types? ==
1115 +(((
1116 +
1117 +)))
852 852  
853 853  (((
854 -NSE01 is calibrated for saline-alkali soil and loamy soil. If users want to use it for other soil, they can calibrate the value in the IoT platform base on the value measured by saline-alkali soil and loamy soil. The formula can be found at [[this link>>https://www.dragino.com/downloads/downloads/LoRa_End_Node/LSE01/Calibrate_to_other_Soil_20220605.pdf]].
1120 +For example, in **US915** band, the frequency table is as below. By default, the end node will use all channels (0~~71) for OTAA Join process. After the OTAA Join, the end node will use these all channels (0~~71) to send uplink packets.
855 855  )))
856 856  
1123 +[[image:image-20220606154726-3.png]]
857 857  
858 -= 6.  Trouble Shooting =
859 859  
860 -== 6.1  ​Connection problem when uploading firmware ==
1126 +When you use the TTN network, the US915 frequency bands use are:
861 861  
1128 +* 903.9 - SF7BW125 to SF10BW125
1129 +* 904.1 - SF7BW125 to SF10BW125
1130 +* 904.3 - SF7BW125 to SF10BW125
1131 +* 904.5 - SF7BW125 to SF10BW125
1132 +* 904.7 - SF7BW125 to SF10BW125
1133 +* 904.9 - SF7BW125 to SF10BW125
1134 +* 905.1 - SF7BW125 to SF10BW125
1135 +* 905.3 - SF7BW125 to SF10BW125
1136 +* 904.6 - SF8BW500
862 862  
863 863  (((
864 -**Please see: **[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting>>url:http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting]]
1139 +Because the end node is now hopping in 72 frequency, it makes it difficult for the devices to Join the TTN network and uplink data. To solve this issue, you can access the device via the AT commands and run:
1140 +
1141 +* (% style="color:#037691" %)**AT+CHE=2**
1142 +* (% style="color:#037691" %)**ATZ**
865 865  )))
866 866  
867 -(% class="wikigeneratedid" %)
868 868  (((
869 869  
1147 +
1148 +to set the end node to work in 8 channel mode. The device will work in Channel 8-15 & 64-71 for OTAA, and channel 8-15 for Uplink.
870 870  )))
871 871  
1151 +(((
1152 +
1153 +)))
872 872  
873 -== 6.2  AT Command input doesn't work ==
1155 +(((
1156 +The **AU915** band is similar. Below are the AU915 Uplink Channels.
1157 +)))
874 874  
1159 +[[image:image-20220606154825-4.png]]
1160 +
1161 +
1162 +== 4.2 ​Can I calibrate LSE01 to different soil types? ==
1163 +
1164 +LSE01 is calibrated for saline-alkali soil and loamy soil. If users want to use it for other soil, they can calibrate the value in the IoT platform base on the value measured by saline-alkali soil and loamy soil. The formula can be found at [[this link>>https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/&file=Calibrate_to_other_Soil_20220605.pdf]].
1165 +
1166 +
1167 += 5. Trouble Shooting =
1168 +
1169 +== 5.1 ​Why I can't join TTN in US915 / AU915 bands? ==
1170 +
1171 +It is due to channel mapping. Please see the [[Eight Channel Mode>>doc:Main.End Device AT Commands and Downlink Command.WebHome||anchor="H7.19EightChannelMode"]] section above for details.
1172 +
1173 +
1174 +== 5.2 AT Command input doesn't work ==
1175 +
875 875  (((
876 876  In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
1178 +)))
877 877  
878 -
1180 +
1181 +== 5.3 Device rejoin in at the second uplink packet ==
1182 +
1183 +(% style="color:#4f81bd" %)**Issue describe as below:**
1184 +
1185 +[[image:1654500909990-784.png]]
1186 +
1187 +
1188 +(% style="color:#4f81bd" %)**Cause for this issue:**
1189 +
1190 +(((
1191 +The fuse on LSE01 is not large enough, some of the soil probe require large current up to 5v 800mA, in a short pulse. When this happen, it cause the device reboot so user see rejoin.
879 879  )))
880 880  
881 881  
882 -= 7. ​ Order Info =
1195 +(% style="color:#4f81bd" %)**Solution: **
883 883  
1197 +All new shipped LSE01 after 2020-May-30 will have this to fix. For the customer who see this issue, please bypass the fuse as below:
884 884  
885 -Part Number**:** (% style="color:#4f81bd" %)**NSE01**
1199 +[[image:1654500929571-736.png||height="458" width="832"]]
886 886  
887 887  
1202 += 6. ​Order Info =
1203 +
1204 +
1205 +Part Number**:** (% style="color:#4f81bd" %)**LSE01-XX-YY**
1206 +
1207 +
1208 +(% style="color:#4f81bd" %)**XX**(%%)**:** The default frequency band
1209 +
1210 +* (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band
1211 +* (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band
1212 +* (% style="color:red" %)**EU433**(%%): LoRaWAN EU433 band
1213 +* (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band
1214 +* (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band
1215 +* (% style="color:red" %)**US915**(%%): LoRaWAN US915 band
1216 +* (% style="color:red" %)**IN865**(%%):  LoRaWAN IN865 band
1217 +* (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
1218 +
1219 +(% style="color:#4f81bd" %)**YY**(%%)**: **Battery Option
1220 +
1221 +* (% style="color:red" %)**4**(%%): 4000mAh battery
1222 +* (% style="color:red" %)**8**(%%): 8500mAh battery
1223 +
888 888  (% class="wikigeneratedid" %)
889 889  (((
890 890  
891 891  )))
892 892  
893 -= 8.  Packing Info =
1229 += 7. Packing Info =
894 894  
895 895  (((
896 896  
897 897  
898 898  (% style="color:#037691" %)**Package Includes**:
1235 +)))
899 899  
900 -* NSE01 NB-IoT Soil Moisture & EC Sensor x 1
901 -* External antenna x 1
1237 +* (((
1238 +LSE01 LoRaWAN Soil Moisture & EC Sensor x 1
902 902  )))
903 903  
904 904  (((
... ... @@ -905,19 +905,24 @@
905 905  
906 906  
907 907  (% style="color:#037691" %)**Dimension and weight**:
1245 +)))
908 908  
909 -* Size: 195 x 125 x 55 mm
910 -* Weight:   420g
1247 +* (((
1248 +Device Size: cm
911 911  )))
1250 +* (((
1251 +Device Weight: g
1252 +)))
1253 +* (((
1254 +Package Size / pcs : cm
1255 +)))
1256 +* (((
1257 +Weight / pcs : g
912 912  
913 -(((
914 914  
915 -
916 -
917 -
918 918  )))
919 919  
920 -= 9.  Support =
1262 += 8. Support =
921 921  
922 922  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
923 923  * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]
1657260785982-288.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -138.2 KB
Content
1657261119050-993.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -126.1 KB
Content
1657261278785-153.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -126.1 KB
Content
1657271519014-786.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -71.5 KB
Content
1657327959271-447.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -78.3 KB
Content
1657328609906-564.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -492.6 KB
Content
image-20220708141352-7.jpeg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -102.7 KB
Content
image-20220709084038-1.jpeg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -72.0 KB
Content
image-20220709084137-2.jpeg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -72.0 KB
Content
image-20220709084207-3.jpeg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -72.0 KB
Content
image-20220709084458-4.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -199.5 KB
Content
image-20220709085040-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -200.4 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0