Changes for page NDDS75 -- NB-IoT Distance Detect Sensor User Manual

Last modified by Bei Jinggeng on 2024/05/31 09:53

From version < 65.4 >

edited by Xiaoling
on 2022/07/08 15:09

To version < 65.14 >

edited by Xiaoling
on 2022/07/08 15:51

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -20,6 +20,7 @@
++
  = 1.  Introduction =
  == 1.1  What is LoRaWAN Soil Moisture & EC Sensor ==
@@ -27,13 +27,21 @@
  (((
++(((
  Dragino NSE01 is an (% style="color:blue" %)**NB-IOT soil moisture & EC sensor**(%%) for agricultural IoT. Used to measure the soil moisture of saline-alkali soil and loam. The soil sensor uses the FDR method to calculate soil moisture and compensates it with soil temperature and electrical conductivity. It has also been calibrated for mineral soil types at the factory.
++)))
++(((
  It can detect (% style="color:blue" %)**Soil Moisture, Soil Temperature and Soil Conductivity**(%%), and upload its value to the server wirelessly.
++)))
++(((
  The wireless technology used in NSE01 allows the device to send data at a low data rate and reach ultra-long distances, providing ultra-long-distance spread spectrum Communication.
++)))
++(((
  NSE01 are powered by (% style="color:blue" %)**8500mAh Li-SOCI2**(%%) batteries, which can be used for up to 5 years.
++)))
  )))
@@ -60,9 +60,6 @@
  * Micro SIM card slot for NB-IoT SIM
  * 8500mAh Battery for long term use
--
--
--
  == 1.3  Specification ==
@@ -71,8 +71,6 @@
  * Supply Voltage: 2.1v ~~ 3.6v
  * Operating Temperature: -40 ~~ 85°C
--
--
  (% style="color:#037691" %)**NB-IoT Spec:**
  * - B1 @H-FDD: 2100MHz
@@ -82,8 +82,6 @@
  * - B20 @H-FDD: 800MHz
  * - B28 @H-FDD: 700MHz
--
--
  Probe(% style="color:#037691" %)** Specification:**
  Measure Volume: Base on the centra pin of the probe, a cylinder with 7cm diameter and 10cm height.
@@ -134,7 +134,9 @@
  === 2.2.1  Test Requirement ===
++(((
  To use NSE01 in your city, make sure meet below requirements:
++)))
  * Your local operator has already distributed a NB-IoT Network there.
  * The local NB-IoT network used the band that NSE01 supports.
@@ -151,9 +151,13 @@
  === 2.2.2  Insert SIM card ===
++(((
  Insert the NB-IoT Card get from your provider.
++)))
++(((
  User need to take out the NB-IoT module and insert the SIM card like below:
++)))
  [[image:1657249468462-536.png]]
@@ -192,7 +192,9 @@
  [[image:image-20220708110657-3.png]]
++(((
  (% style="color:red" %)Note: the valid AT Commands can be found at: (%%)[[http:~~/~~/www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/]]
++)))
@@ -295,12 +295,14 @@
  In this mode, uplink payload includes in total 18 bytes
  (% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:510px" %)
--|=(% style="width: 50px;" %)(((
++|=(% style="width: 60px;" %)(((
  **Size(bytes)**
--)))|=(% style="width: 50px;" %)**6**|=(% style="width: 25px;" %)2|=(% style="width: 25px;" %)**2**|=(% style="width: 80px;" %)**1**|=(% style="width: 80px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 40px;" %)**1**
++)))|=(% style="width: 50px;" %)**6**|=(% style="width: 25px;" %)2|=(% style="width: 25px;" %)**2**|=(% style="width: 70px;" %)**1**|=(% style="width: 60px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 90px;" %)**2**|=(% style="width: 50px;" %)**1**
  |(% style="width:97px" %)**Value**|(% style="width:83px" %)[[Device ID>>||anchor="H2.4.1A0A0DeviceID"]]|(% style="width:41px" %)[[Ver>>||anchor="H2.4.2A0VersionInfo"]]|(% style="width:46px" %)[[BAT>>||anchor="H2.4.3A0BatteryInfo"]]|(% style="width:123px" %)[[Signal Strength>>||anchor="H2.4.4A0SignalStrength"]]|(% style="width:108px" %)[[Soil Moisture>>||anchor="H2.4.5A0SoilMoisture"]]|(% style="width:133px" %)[[Soil Temperature>>||anchor="H2.4.6A0SoilTemperature"]]|(% style="width:159px" %)[[Soil Conductivity(EC)>>||anchor="H2.4.7A0SoilConductivity28EC29"]]|(% style="width:80px" %)[[Interrupt>>||anchor="H2.4.8A0DigitalInterrupt"]]
++(((
  If we use the MQTT client to subscribe to this MQTT topic, we can see the following information when the NSE01 uplink data.
++)))
  [[image:image-20220708111918-4.png]]
@@ -328,23 +328,37 @@
  === 2.4.1  Device ID ===
++(((
  By default, the Device ID equal to the last 6 bytes of IMEI.
++)))
++(((
  User can use (% style="color:blue" %)**AT+DEUI**(%%) to set Device ID
++)))
++(((
  **Example:**
++)))
++(((
  AT+DEUI=A84041F15612
++)))
++(((
  The Device ID is stored in a none-erase area, Upgrade the firmware or run AT+FDR won't erase Device ID.
++)))
  === 2.4.2  Version Info ===
++(((
  Specify the software version: 0x64=100, means firmware version 1.00.
++)))
++(((
  For example: 0x00 64 : this device is NSE01 with firmware version 1.0.0.
++)))
@@ -366,19 +366,33 @@
  === 2.4.4  Signal Strength ===
++(((
  NB-IoT Network signal Strength.
++)))
++(((
  **Ex1: 0x1d = 29**
++)))
++(((
  (% style="color:blue" %)**0**(%%)        -113dBm or less
++)))
++(((
  (% style="color:blue" %)**1**(%%)        -111dBm
++)))
++(((
  (% style="color:blue" %)**2...30**(%%) -109dBm... -53dBm
++)))
++(((
  (% style="color:blue" %)**31**  (%%)    -51dBm or greater
++)))
++(((
  (% style="color:blue" %)**99**   (%%)   Not known or not detectable
++)))
@@ -385,12 +385,16 @@
  === 2.4.5  Soil Moisture ===
  (((
++(((
  Get the moisture content of the soil. The value range of the register is 0-10000(Decimal), divide this value by 100 to get the percentage of moisture in the soil.
  )))
++)))
  (((
++(((
  For example, if the data you get from the register is **__0x05 0xDC__**, the moisture content in the soil is
  )))
++)))
  (((
@@ -405,7 +405,7 @@
  === 2.4.6  Soil Temperature ===
  (((
-- Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is __**0x09 0xEC**__, the temperature content in the soil is
++Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is __**0x09 0xEC**__, the temperature content in the soil is
  )))
  (((
@@ -453,7 +453,7 @@
  (% style="color:blue" %)**AT+INTMOD=3 **(%%)   ~/~/(more info about INMOD please refer [[**AT Command Manual**>>url:https://www.dragino.com/downloads/downloads/NB-IoT/NBSN95/DRAGINO_NBSN95-NB_AT%20Commands_v1.1.0.pdf]])**.**
--The lower four bits of this data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H"]] for the hardware and software set up.
++The lower four bits of this data field shows if this packet is generated by interrupt or not. Click here for the hardware and software set up.
  Example:
@@ -578,7 +578,7 @@
  [[www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/Firmware/]]
--Upgrade Instruction: [[Upgrade_Firmware>>||anchor="H"]]
++Upgrade Instruction: [[Upgrade_Firmware>>||anchor="H5.1200BHowtoUpgradeFirmware"]]
@@ -596,7 +596,7 @@
  The battery related documents as below:
  * [[Battery Dimension>>http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
--* [[Lithium-Thionyl Chloride Battery>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]][[ datasheet>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
++* [[Lithium-Thionyl Chloride Battery datasheet>>http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
  * [[Lithium-ion Battery-Capacitor datasheet>>http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
  (((

Changes for page NDDS75 -- NB-IoT Distance Detect Sensor User Manual

Summary

Details

Applications

Navigation