Last modified by Bei Jinggeng on 2024/05/31 09:53
<
From version < 65.18 >
edited by Xiaoling
on 2022/07/08 15:53
To version < 59.1 >
edited by Xiaoling
on 2022/07/08 13:54
>
Change comment: Uploaded new attachment "1657259653666-883.png", version {1}

Summary

Details

Page properties
Content
... ... @@ -13,14 +13,11 @@
13 13  
14 14  **Table of Contents:**
15 15  
16 -{{toc/}}
17 17  
18 18  
19 19  
20 20  
21 21  
22 -
23 -
24 24  = 1.  Introduction =
25 25  
26 26  == 1.1 ​ What is LoRaWAN Soil Moisture & EC Sensor ==
... ... @@ -28,21 +28,13 @@
28 28  (((
29 29  
30 30  
31 -(((
32 32  Dragino NSE01 is an (% style="color:blue" %)**NB-IOT soil moisture & EC sensor**(%%) for agricultural IoT. Used to measure the soil moisture of saline-alkali soil and loam. The soil sensor uses the FDR method to calculate soil moisture and compensates it with soil temperature and electrical conductivity. It has also been calibrated for mineral soil types at the factory.
33 -)))
34 34  
35 -(((
36 36  It can detect (% style="color:blue" %)**Soil Moisture, Soil Temperature and Soil Conductivity**(%%), and upload its value to the server wirelessly.
37 -)))
38 38  
39 -(((
40 40  The wireless technology used in NSE01 allows the device to send data at a low data rate and reach ultra-long distances, providing ultra-long-distance spread spectrum Communication.
41 -)))
42 42  
43 -(((
44 44  NSE01 are powered by (% style="color:blue" %)**8500mAh Li-SOCI2**(%%) batteries, which can be used for up to 5 years.  
45 -)))
46 46  
47 47  
48 48  )))
... ... @@ -54,8 +54,9 @@
54 54  
55 55  
56 56  
57 -== 1.2 ​ Features ==
46 +== 1.2 ​Features ==
58 58  
48 +
59 59  * NB-IoT Bands: B1/B3/B8/B5/B20/B28 @H-FDD
60 60  * Monitor Soil Moisture
61 61  * Monitor Soil Temperature
... ... @@ -86,7 +86,7 @@
86 86  * - B20 @H-FDD: 800MHz
87 87  * - B28 @H-FDD: 700MHz
88 88  
89 -Probe(% style="color:#037691" %)** Specification:**
79 +(% style="color:#037691" %)**Probe Specification:**
90 90  
91 91  Measure Volume: Base on the centra pin of the probe, a cylinder with 7cm diameter and 10cm height.
92 92  
... ... @@ -136,9 +136,7 @@
136 136  === 2.2.1 Test Requirement ===
137 137  
138 138  
139 -(((
140 140  To use NSE01 in your city, make sure meet below requirements:
141 -)))
142 142  
143 143  * Your local operator has already distributed a NB-IoT Network there.
144 144  * The local NB-IoT network used the band that NSE01 supports.
... ... @@ -155,13 +155,9 @@
155 155  
156 156  === 2.2.2 Insert SIM card ===
157 157  
158 -(((
159 159  Insert the NB-IoT Card get from your provider.
160 -)))
161 161  
162 -(((
163 163  User need to take out the NB-IoT module and insert the SIM card like below:
164 -)))
165 165  
166 166  
167 167  [[image:1657249468462-536.png]]
... ... @@ -200,9 +200,7 @@
200 200  
201 201  [[image:image-20220708110657-3.png]]
202 202  
203 -(((
204 204  (% style="color:red" %)Note: the valid AT Commands can be found at: (%%)[[http:~~/~~/www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/]]
205 -)))
206 206  
207 207  
208 208  
... ... @@ -305,14 +305,12 @@
305 305  In this mode, uplink payload includes in total 18 bytes
306 306  
307 307  (% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:510px" %)
308 -|=(% style="width: 60px;" %)(((
290 +|=(% style="width: 50px;" %)(((
309 309  **Size(bytes)**
310 -)))|=(% style="width: 50px;" %)**6**|=(% style="width: 25px;" %)2|=(% style="width: 25px;" %)**2**|=(% style="width: 70px;" %)**1**|=(% style="width: 60px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 90px;" %)**2**|=(% style="width: 50px;" %)**1**
311 -|(% style="width:97px" %)**Value**|(% style="width:83px" %)[[Device ID>>||anchor="H2.4.1A0A0DeviceID"]]|(% style="width:41px" %)[[Ver>>||anchor="H2.4.2A0VersionInfo"]]|(% style="width:46px" %)[[BAT>>||anchor="H2.4.3A0BatteryInfo"]]|(% style="width:123px" %)[[Signal Strength>>||anchor="H2.4.4A0SignalStrength"]]|(% style="width:108px" %)[[Soil Moisture>>||anchor="H2.4.5A0SoilMoisture"]]|(% style="width:133px" %)[[Soil Temperature>>||anchor="H2.4.6A0SoilTemperature"]]|(% style="width:159px" %)[[Soil Conductivity(EC)>>||anchor="H2.4.7A0SoilConductivity28EC29"]]|(% style="width:80px" %)[[Interrupt>>||anchor="H2.4.8A0DigitalInterrupt"]]
292 +)))|=(% style="width: 50px;" %)**6**|=(% style="width: 25px;" %)2|=(% style="width: 25px;" %)**2**|=(% style="width: 80px;" %)**1**|=(% style="width: 80px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 40px;" %)**1**
293 +|(% style="width:97px" %)**Value**|(% style="width:83px" %)[[Device ID>>||anchor="H"]]|(% style="width:41px" %)[[Ver>>||anchor="H"]]|(% style="width:46px" %)[[BAT>>||anchor="H"]]|(% style="width:123px" %)[[Signal Strength>>||anchor="H"]]|(% style="width:108px" %)[[Soil Moisture>>||anchor="H"]]|(% style="width:133px" %)[[Soil Temperature>>||anchor="H"]]|(% style="width:159px" %)[[Soil Conductivity(EC)>>||anchor="H"]]|(% style="width:80px" %)[[Interrupt>>||anchor="H"]]
312 312  
313 -(((
314 314  If we use the MQTT client to subscribe to this MQTT topic, we can see the following information when the NSE01 uplink data.
315 -)))
316 316  
317 317  
318 318  [[image:image-20220708111918-4.png]]
... ... @@ -333,44 +333,28 @@
333 333  * Interrupt: 0x00 = 0
334 334  
335 335  
336 -
337 -
338 338  == 2.4  Payload Explanation and Sensor Interface ==
339 339  
340 340  
341 341  === 2.4.1  Device ID ===
342 342  
343 -(((
344 344  By default, the Device ID equal to the last 6 bytes of IMEI.
345 -)))
346 346  
347 -(((
348 348  User can use (% style="color:blue" %)**AT+DEUI**(%%) to set Device ID
349 -)))
350 350  
351 -(((
352 352  **Example:**
353 -)))
354 354  
355 -(((
356 356  AT+DEUI=A84041F15612
357 -)))
358 358  
359 -(((
360 360  The Device ID is stored in a none-erase area, Upgrade the firmware or run AT+FDR won't erase Device ID.
361 -)))
362 362  
363 363  
364 364  
365 365  === 2.4.2  Version Info ===
366 366  
367 -(((
368 368  Specify the software version: 0x64=100, means firmware version 1.00.
369 -)))
370 370  
371 -(((
372 372  For example: 0x00 64 : this device is NSE01 with firmware version 1.0.0.
373 -)))
374 374  
375 375  
376 376  
... ... @@ -392,33 +392,19 @@
392 392  
393 393  === 2.4.4  Signal Strength ===
394 394  
395 -(((
396 396  NB-IoT Network signal Strength.
397 -)))
398 398  
399 -(((
400 400  **Ex1: 0x1d = 29**
401 -)))
402 402  
403 -(((
404 404  (% style="color:blue" %)**0**(%%)  -113dBm or less
405 -)))
406 406  
407 -(((
408 408  (% style="color:blue" %)**1**(%%)  -111dBm
409 -)))
410 410  
411 -(((
412 412  (% style="color:blue" %)**2...30**(%%) -109dBm... -53dBm
413 -)))
414 414  
415 -(((
416 416  (% style="color:blue" %)**31**  (%%) -51dBm or greater
417 -)))
418 418  
419 -(((
420 420  (% style="color:blue" %)**99**   (%%) Not known or not detectable
421 -)))
422 422  
423 423  
424 424  
... ... @@ -425,16 +425,12 @@
425 425  === 2.4.5  Soil Moisture ===
426 426  
427 427  (((
428 -(((
429 429  Get the moisture content of the soil. The value range of the register is 0-10000(Decimal), divide this value by 100 to get the percentage of moisture in the soil.
430 430  )))
431 -)))
432 432  
433 433  (((
434 -(((
435 435  For example, if the data you get from the register is **__0x05 0xDC__**, the moisture content in the soil is
436 436  )))
437 -)))
438 438  
439 439  (((
440 440  
... ... @@ -449,7 +449,7 @@
449 449  === 2.4.6  Soil Temperature ===
450 450  
451 451  (((
452 -Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is __**0x09 0xEC**__, the temperature content in the soil is
398 + Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is __**0x09 0xEC**__, the temperature content in the soil is
453 453  )))
454 454  
455 455  (((
... ... @@ -490,66 +490,45 @@
490 490  
491 491  === 2.4.8  Digital Interrupt ===
492 492  
493 -(((
494 494  Digital Interrupt refers to pin (% style="color:blue" %)**GPIO_EXTI**(%%), and there are different trigger methods. When there is a trigger, the NSE01 will send a packet to the server.
495 -)))
496 496  
497 -(((
498 498  The command is:
499 -)))
500 500  
501 -(((
502 502  (% style="color:blue" %)**AT+INTMOD=3 **(%%) ~/~/(more info about INMOD please refer [[**AT Command Manual**>>url:https://www.dragino.com/downloads/downloads/NB-IoT/NBSN95/DRAGINO_NBSN95-NB_AT%20Commands_v1.1.0.pdf]])**.**
503 -)))
504 504  
505 505  
506 -(((
507 -The lower four bits of this data field shows if this packet is generated by interrupt or not. Click here for the hardware and software set up.
508 -)))
446 +The lower four bits of this data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H"]] for the hardware and software set up.
509 509  
510 510  
511 -(((
512 512  Example:
513 -)))
514 514  
515 -(((
516 516  0x(00): Normal uplink packet.
517 -)))
518 518  
519 -(((
520 520  0x(01): Interrupt Uplink Packet.
521 -)))
522 522  
523 523  
524 524  
525 525  === 2.4.9  ​+5V Output ===
526 526  
527 -(((
528 528  NSE01 will enable +5V output before all sampling and disable the +5v after all sampling. 
529 -)))
530 530  
531 531  
532 -(((
533 533  The 5V output time can be controlled by AT Command.
534 -)))
535 535  
536 -(((
537 537  (% style="color:blue" %)**AT+5VT=1000**
538 -)))
539 539  
540 -(((
541 541  Means set 5V valid time to have 1000ms. So the real 5V output will actually have 1000ms + sampling time for other sensors.
542 -)))
543 543  
544 544  
545 545  
546 546  == 2.5  Downlink Payload ==
547 547  
548 -By default, NSE01 prints the downlink payload to console port.
472 +By default, LSE50 prints the downlink payload to console port.
549 549  
550 550  [[image:image-20220708133731-5.png]]
551 551  
552 552  
477 +
553 553  (((
554 554  (% style="color:blue" %)**Examples:**
555 555  )))
... ... @@ -563,7 +563,7 @@
563 563  )))
564 564  
565 565  (((
566 -If the payload=0100003C, it means set the END Node's TDC to 0x00003C=60(S), while type code is 01.
491 +If the payload=0100003C, it means set the END Node’s TDC to 0x00003C=60(S), while type code is 01.
567 567  )))
568 568  
569 569  (((
... ... @@ -583,144 +583,432 @@
583 583  )))
584 584  
585 585  (((
586 -If payload = 0x04FF, it will reset the NSE01
511 +If payload = 0x04FF, it will reset the LSE01
587 587  )))
588 588  
589 589  
590 -* (% style="color:blue" %)**INTMOD**
515 +* (% style="color:blue" %)**CFM**
591 591  
592 -(((
593 -Downlink Payload: 06000003, Set AT+INTMOD=3
594 -)))
517 +Downlink Payload: 05000001, Set AT+CFM=1 or 05000000 , set AT+CFM=0
595 595  
596 596  
597 597  
598 -== 2.6  ​LED Indicator ==
521 +== 2.6 ​Show Data in DataCake IoT Server ==
599 599  
600 600  (((
601 -The NSE01 has an internal LED which is to show the status of different state.
524 +[[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:
525 +)))
602 602  
527 +(((
528 +
529 +)))
603 603  
604 -* When power on, NSE01 will detect if sensor probe is connected, if probe detected, LED will blink four times. (no blinks in this step is no probe)
605 -* Then the LED will be on for 1 second means device is boot normally.
606 -* After NSE01 join NB-IoT network. The LED will be ON for 3 seconds.
607 -* For each uplink probe, LED will be on for 500ms.
531 +(((
532 +(% style="color:blue" %)**Step 1**(%%):  Be sure that your device is programmed and properly connected to the network at this time.
608 608  )))
609 609  
535 +(((
536 +(% style="color:blue" %)**Step 2**(%%):  To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:
537 +)))
610 610  
611 611  
540 +[[image:1654505857935-743.png]]
612 612  
613 -== 2.7  Installation in Soil ==
614 614  
615 -__**Measurement the soil surface**__
543 +[[image:1654505874829-548.png]]
616 616  
617 -(((
618 -Choose the proper measuring position. Avoid the probe to touch rocks or hard things. Split the surface soil according to the measured deep. Keep the measured as original density. Vertical insert the probe into the soil to be measured. Make sure not shake when inserting. [[https:~~/~~/img.alicdn.com/imgextra/i3/2005165265/O1CN010rj9Oh1olPsQxrdUK_!!2005165265.jpg>>url:https://img.alicdn.com/imgextra/i3/2005165265/O1CN010rj9Oh1olPsQxrdUK_!!2005165265.jpg]]
619 -)))
620 620  
621 -[[image:1657259653666-883.png]] ​
546 +(% style="color:blue" %)**Step 3**(%%)**:**  Create an account or log in Datacake.
622 622  
548 +(% style="color:blue" %)**Step 4**(%%)**:**  Search the LSE01 and add DevEUI.
623 623  
624 -(((
625 -
626 626  
627 -(((
628 -Dig a hole with diameter > 20CM.
629 -)))
551 +[[image:1654505905236-553.png]]
630 630  
631 -(((
632 -Horizontal insert the probe to the soil and fill the hole for long term measurement.
633 -)))
634 -)))
635 635  
636 -[[image:1654506665940-119.png]]
554 +After added, the sensor data arrive TTN, it will also arrive and show in Mydevices.
637 637  
638 -(((
639 -
640 -)))
556 +[[image:1654505925508-181.png]]
641 641  
642 642  
643 -== 2.8  ​Firmware Change Log ==
644 644  
560 +== 2.7 Frequency Plans ==
645 645  
646 -Download URL & Firmware Change log
562 +The LSE01 uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
647 647  
648 -[[www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/Firmware/]]
649 649  
565 +=== 2.7.1 EU863-870 (EU868) ===
650 650  
651 -Upgrade Instruction: [[Upgrade_Firmware>>||anchor="H5.1200BHowtoUpgradeFirmware"]]
567 +(% style="color:#037691" %)** Uplink:**
652 652  
569 +868.1 - SF7BW125 to SF12BW125
653 653  
571 +868.3 - SF7BW125 to SF12BW125 and SF7BW250
654 654  
655 -== 2.9  ​Battery Analysis ==
573 +868.5 - SF7BW125 to SF12BW125
656 656  
657 -=== 2.9.1  ​Battery Type ===
575 +867.1 - SF7BW125 to SF12BW125
658 658  
577 +867.3 - SF7BW125 to SF12BW125
659 659  
579 +867.5 - SF7BW125 to SF12BW125
580 +
581 +867.7 - SF7BW125 to SF12BW125
582 +
583 +867.9 - SF7BW125 to SF12BW125
584 +
585 +868.8 - FSK
586 +
587 +
588 +(% style="color:#037691" %)** Downlink:**
589 +
590 +Uplink channels 1-9 (RX1)
591 +
592 +869.525 - SF9BW125 (RX2 downlink only)
593 +
594 +
595 +
596 +=== 2.7.2 US902-928(US915) ===
597 +
598 +Used in USA, Canada and South America. Default use CHE=2
599 +
600 +(% style="color:#037691" %)**Uplink:**
601 +
602 +903.9 - SF7BW125 to SF10BW125
603 +
604 +904.1 - SF7BW125 to SF10BW125
605 +
606 +904.3 - SF7BW125 to SF10BW125
607 +
608 +904.5 - SF7BW125 to SF10BW125
609 +
610 +904.7 - SF7BW125 to SF10BW125
611 +
612 +904.9 - SF7BW125 to SF10BW125
613 +
614 +905.1 - SF7BW125 to SF10BW125
615 +
616 +905.3 - SF7BW125 to SF10BW125
617 +
618 +
619 +(% style="color:#037691" %)**Downlink:**
620 +
621 +923.3 - SF7BW500 to SF12BW500
622 +
623 +923.9 - SF7BW500 to SF12BW500
624 +
625 +924.5 - SF7BW500 to SF12BW500
626 +
627 +925.1 - SF7BW500 to SF12BW500
628 +
629 +925.7 - SF7BW500 to SF12BW500
630 +
631 +926.3 - SF7BW500 to SF12BW500
632 +
633 +926.9 - SF7BW500 to SF12BW500
634 +
635 +927.5 - SF7BW500 to SF12BW500
636 +
637 +923.3 - SF12BW500(RX2 downlink only)
638 +
639 +
640 +
641 +=== 2.7.3 CN470-510 (CN470) ===
642 +
643 +Used in China, Default use CHE=1
644 +
645 +(% style="color:#037691" %)**Uplink:**
646 +
647 +486.3 - SF7BW125 to SF12BW125
648 +
649 +486.5 - SF7BW125 to SF12BW125
650 +
651 +486.7 - SF7BW125 to SF12BW125
652 +
653 +486.9 - SF7BW125 to SF12BW125
654 +
655 +487.1 - SF7BW125 to SF12BW125
656 +
657 +487.3 - SF7BW125 to SF12BW125
658 +
659 +487.5 - SF7BW125 to SF12BW125
660 +
661 +487.7 - SF7BW125 to SF12BW125
662 +
663 +
664 +(% style="color:#037691" %)**Downlink:**
665 +
666 +506.7 - SF7BW125 to SF12BW125
667 +
668 +506.9 - SF7BW125 to SF12BW125
669 +
670 +507.1 - SF7BW125 to SF12BW125
671 +
672 +507.3 - SF7BW125 to SF12BW125
673 +
674 +507.5 - SF7BW125 to SF12BW125
675 +
676 +507.7 - SF7BW125 to SF12BW125
677 +
678 +507.9 - SF7BW125 to SF12BW125
679 +
680 +508.1 - SF7BW125 to SF12BW125
681 +
682 +505.3 - SF12BW125 (RX2 downlink only)
683 +
684 +
685 +
686 +=== 2.7.4 AU915-928(AU915) ===
687 +
688 +Default use CHE=2
689 +
690 +(% style="color:#037691" %)**Uplink:**
691 +
692 +916.8 - SF7BW125 to SF12BW125
693 +
694 +917.0 - SF7BW125 to SF12BW125
695 +
696 +917.2 - SF7BW125 to SF12BW125
697 +
698 +917.4 - SF7BW125 to SF12BW125
699 +
700 +917.6 - SF7BW125 to SF12BW125
701 +
702 +917.8 - SF7BW125 to SF12BW125
703 +
704 +918.0 - SF7BW125 to SF12BW125
705 +
706 +918.2 - SF7BW125 to SF12BW125
707 +
708 +
709 +(% style="color:#037691" %)**Downlink:**
710 +
711 +923.3 - SF7BW500 to SF12BW500
712 +
713 +923.9 - SF7BW500 to SF12BW500
714 +
715 +924.5 - SF7BW500 to SF12BW500
716 +
717 +925.1 - SF7BW500 to SF12BW500
718 +
719 +925.7 - SF7BW500 to SF12BW500
720 +
721 +926.3 - SF7BW500 to SF12BW500
722 +
723 +926.9 - SF7BW500 to SF12BW500
724 +
725 +927.5 - SF7BW500 to SF12BW500
726 +
727 +923.3 - SF12BW500(RX2 downlink only)
728 +
729 +
730 +
731 +=== 2.7.5 AS920-923 & AS923-925 (AS923) ===
732 +
733 +(% style="color:#037691" %)**Default Uplink channel:**
734 +
735 +923.2 - SF7BW125 to SF10BW125
736 +
737 +923.4 - SF7BW125 to SF10BW125
738 +
739 +
740 +(% style="color:#037691" %)**Additional Uplink Channel**:
741 +
742 +(OTAA mode, channel added by JoinAccept message)
743 +
744 +(% style="color:#037691" %)**AS920~~AS923 for Japan, Malaysia, Singapore**:
745 +
746 +922.2 - SF7BW125 to SF10BW125
747 +
748 +922.4 - SF7BW125 to SF10BW125
749 +
750 +922.6 - SF7BW125 to SF10BW125
751 +
752 +922.8 - SF7BW125 to SF10BW125
753 +
754 +923.0 - SF7BW125 to SF10BW125
755 +
756 +922.0 - SF7BW125 to SF10BW125
757 +
758 +
759 +(% style="color:#037691" %)**AS923 ~~ AS925 for Brunei, Cambodia, Hong Kong, Indonesia, Laos, Taiwan, Thailand, Vietnam**:
760 +
761 +923.6 - SF7BW125 to SF10BW125
762 +
763 +923.8 - SF7BW125 to SF10BW125
764 +
765 +924.0 - SF7BW125 to SF10BW125
766 +
767 +924.2 - SF7BW125 to SF10BW125
768 +
769 +924.4 - SF7BW125 to SF10BW125
770 +
771 +924.6 - SF7BW125 to SF10BW125
772 +
773 +
774 +(% style="color:#037691" %)** Downlink:**
775 +
776 +Uplink channels 1-8 (RX1)
777 +
778 +923.2 - SF10BW125 (RX2)
779 +
780 +
781 +
782 +=== 2.7.6 KR920-923 (KR920) ===
783 +
784 +Default channel:
785 +
786 +922.1 - SF7BW125 to SF12BW125
787 +
788 +922.3 - SF7BW125 to SF12BW125
789 +
790 +922.5 - SF7BW125 to SF12BW125
791 +
792 +
793 +(% style="color:#037691" %)**Uplink: (OTAA mode, channel added by JoinAccept message)**
794 +
795 +922.1 - SF7BW125 to SF12BW125
796 +
797 +922.3 - SF7BW125 to SF12BW125
798 +
799 +922.5 - SF7BW125 to SF12BW125
800 +
801 +922.7 - SF7BW125 to SF12BW125
802 +
803 +922.9 - SF7BW125 to SF12BW125
804 +
805 +923.1 - SF7BW125 to SF12BW125
806 +
807 +923.3 - SF7BW125 to SF12BW125
808 +
809 +
810 +(% style="color:#037691" %)**Downlink:**
811 +
812 +Uplink channels 1-7(RX1)
813 +
814 +921.9 - SF12BW125 (RX2 downlink only; SF12BW125 might be changed to SF9BW125)
815 +
816 +
817 +
818 +=== 2.7.7 IN865-867 (IN865) ===
819 +
820 +(% style="color:#037691" %)** Uplink:**
821 +
822 +865.0625 - SF7BW125 to SF12BW125
823 +
824 +865.4025 - SF7BW125 to SF12BW125
825 +
826 +865.9850 - SF7BW125 to SF12BW125
827 +
828 +
829 +(% style="color:#037691" %) **Downlink:**
830 +
831 +Uplink channels 1-3 (RX1)
832 +
833 +866.550 - SF10BW125 (RX2)
834 +
835 +
836 +
837 +
838 +== 2.8 LED Indicator ==
839 +
840 +The LSE01 has an internal LED which is to show the status of different state.
841 +
842 +* Blink once when device power on.
843 +* Solid ON for 5 seconds once device successful Join the network.
844 +* Blink once when device transmit a packet.
845 +
846 +== 2.9 Installation in Soil ==
847 +
848 +**Measurement the soil surface**
849 +
850 +
851 +[[image:1654506634463-199.png]] ​
852 +
660 660  (((
661 -The NSE01 battery is a combination of an 8500mAh Li/SOCI2 Battery and a Super Capacitor. The battery is none-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
854 +(((
855 +Choose the proper measuring position. Avoid the probe to touch rocks or hard things. Split the surface soil according to the measured deep. Keep the measured as original density. Vertical insert the probe into the soil to be measured. Make sure not shake when inserting.
662 662  )))
857 +)))
663 663  
664 664  
860 +
861 +[[image:1654506665940-119.png]]
862 +
665 665  (((
666 -The battery is designed to last for several years depends on the actually use environment and update interval. 
864 +Dig a hole with diameter > 20CM.
667 667  )))
668 668  
867 +(((
868 +Horizontal insert the probe to the soil and fill the hole for long term measurement.
869 +)))
669 669  
871 +
872 +== 2.10 ​Firmware Change Log ==
873 +
670 670  (((
671 -The battery related documents as below:
875 +**Firmware download link:**
672 672  )))
673 673  
674 -* [[Battery Dimension>>http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
675 -* [[Lithium-Thionyl Chloride Battery datasheet>>http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
676 -* [[Lithium-ion Battery-Capacitor datasheet>>http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
878 +(((
879 +[[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/]]
880 +)))
677 677  
678 678  (((
679 -[[image:image-20220708140453-6.png]]
883 +
680 680  )))
681 681  
886 +(((
887 +**Firmware Upgrade Method: **[[Firmware Upgrade Instruction>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome]]
888 +)))
682 682  
890 +(((
891 +
892 +)))
683 683  
684 -=== 2.9.2  Power consumption Analyze ===
894 +(((
895 +**V1.0.**
896 +)))
685 685  
686 686  (((
687 -Dragino battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
899 +Release
688 688  )))
689 689  
690 690  
903 +== 2.11 ​Battery Analysis ==
904 +
905 +=== 2.11.1 ​Battery Type ===
906 +
691 691  (((
692 -Instruction to use as below:
908 +The LSE01 battery is a combination of a 4000mAh Li/SOCI2 Battery and a Super Capacitor. The battery is non-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
693 693  )))
694 694  
695 695  (((
696 -(% style="color:blue" %)**Step 1:  **(%%)Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/]]
912 +The battery is designed to last for more than 5 years for the LSN50.
697 697  )))
698 698  
699 -
700 700  (((
701 -(% style="color:blue" %)**Step 2: **(%%) Open it and choose
916 +(((
917 +The battery-related documents are as below:
702 702  )))
919 +)))
703 703  
704 704  * (((
705 -Product Model
922 +[[Battery Dimension>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/]],
706 706  )))
707 707  * (((
708 -Uplink Interval
925 +[[Lithium-Thionyl Chloride Battery  datasheet>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/]],
709 709  )))
710 710  * (((
711 -Working Mode
928 +[[Lithium-ion Battery-Capacitor datasheet>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/]], [[Tech Spec>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/]]
712 712  )))
713 713  
714 -(((
715 -And the Life expectation in difference case will be shown on the right.
716 -)))
931 + [[image:image-20220610172436-1.png]]
717 717  
718 -[[image:image-20220708141352-7.jpeg]]
719 719  
720 720  
935 +=== 2.11.2 ​Battery Note ===
721 721  
722 -=== 2.9.3  ​Battery Note ===
723 -
724 724  (((
725 725  The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
726 726  )))
... ... @@ -727,166 +727,302 @@
727 727  
728 728  
729 729  
730 -=== 2.9.4  Replace the battery ===
943 +=== 2.11.3 Replace the battery ===
731 731  
732 732  (((
733 -The default battery pack of NSE01 includes a ER26500 plus super capacitor. If user can't find this pack locally, they can find ER26500 or equivalence without the SPC1520 capacitor, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes).
946 +If Battery is lower than 2.7v, user should replace the battery of LSE01.
734 734  )))
735 735  
736 -
737 -
738 -= 3. ​ Access NB-IoT Module =
739 -
740 740  (((
741 -Users can directly access the AT command set of the NB-IoT module.
950 +You can change the battery in the LSE01.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
742 742  )))
743 743  
744 744  (((
745 -The AT Command set can refer the BC35-G NB-IoT Module AT Command: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/]] 
954 +The default battery pack of LSE01 includes a ER18505 plus super capacitor. If user can’t find this pack locally, they can find ER18505 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
746 746  )))
747 747  
748 -[[image:1657261278785-153.png]]
749 749  
750 750  
959 += 3. ​Using the AT Commands =
751 751  
752 -= 4.  Using the AT Commands =
961 +== 3.1 Access AT Commands ==
753 753  
754 -== 4.1  Access AT Commands ==
755 755  
756 -See this link for detail: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/]]
964 +LSE01 supports AT Command set in the stock firmware. You can use a USB to TTL adapter to connect to LSE01 for using AT command, as below.
757 757  
966 +[[image:1654501986557-872.png||height="391" width="800"]]
758 758  
759 -AT+<CMD>?  : Help on <CMD>
760 760  
761 -AT+<CMD>         : Run <CMD>
969 +Or if you have below board, use below connection:
762 762  
763 -AT+<CMD>=<value> : Set the value
764 764  
765 -AT+<CMD>=?  : Get the value
972 +[[image:1654502005655-729.png||height="503" width="801"]]
766 766  
767 767  
975 +
976 +In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LSE01. LSE01 will output system info once power on as below:
977 +
978 +
979 + [[image:1654502050864-459.png||height="564" width="806"]]
980 +
981 +
982 +Below are the available commands, a more detailed AT Command manual can be found at [[AT Command Manual>>https://www.dropbox.com/sh/qr6vproz4z4kzjz/AAAD48h3OyWrU1hq_Cqm8jIwa?dl=0]]: [[https:~~/~~/www.dropbox.com/sh/qr6vproz4z4kzjz/AAAD48h3OyWrU1hq_Cqm8jIwa?dl=0>>https://www.dropbox.com/sh/qr6vproz4z4kzjz/AAAD48h3OyWrU1hq_Cqm8jIwa?dl=0]]
983 +
984 +
985 +(% style="background-color:#dcdcdc" %)**AT+<CMD>=?AT+<CMD>? **(%%) : Help on <CMD>
986 +
987 +(% style="background-color:#dcdcdc" %)**AT+<CMD>=?AT+<CMD> **(%%) : Run <CMD>
988 +
989 +(% style="background-color:#dcdcdc" %)**AT+<CMD>=?AT+<CMD>=<value>**(%%) : Set the value
990 +
991 +(% style="background-color:#dcdcdc" %)**AT+<CMD>=?AT+<CMD>=?**(%%)  : Get the value
992 +
993 +
768 768  (% style="color:#037691" %)**General Commands**(%%)      
769 769  
770 -AT  : Attention       
996 +(% style="background-color:#dcdcdc" %)**AT**(%%)  : Attention       
771 771  
772 -AT?  : Short Help     
998 +(% style="background-color:#dcdcdc" %)**AT?**(%%)  : Short Help     
773 773  
774 -ATZ  : MCU Reset    
1000 +(% style="background-color:#dcdcdc" %)**ATZ**(%%)  : MCU Reset    
775 775  
776 -AT+TDC  : Application Data Transmission Interval
1002 +(% style="background-color:#dcdcdc" %)**AT+TDC**(%%)  : Application Data Transmission Interval 
777 777  
778 -AT+CFG  : Print all configurations
779 779  
780 -AT+CFGMOD           : Working mode selection
1005 +(% style="color:#037691" %)**Keys, IDs and EUIs management**
781 781  
782 -AT+INTMOD            : Set the trigger interrupt mode
1007 +(% style="background-color:#dcdcdc" %)**AT+APPEUI**(%%)              : Application EUI      
783 783  
784 -AT+5VT  : Set extend the time of 5V power  
1009 +(% style="background-color:#dcdcdc" %)**AT+APPKEY**(%%)              : Application Key     
785 785  
786 -AT+PRO  : Choose agreement
1011 +(% style="background-color:#dcdcdc" %)**AT+APPSKEY**(%%)            : Application Session Key
787 787  
788 -AT+WEIGRE  : Get weight or set weight to 0
1013 +(% style="background-color:#dcdcdc" %)**AT+DADDR**(%%)              : Device Address     
789 789  
790 -AT+WEIGAP  : Get or Set the GapValue of weight
1015 +(% style="background-color:#dcdcdc" %)**AT+DEUI**(%%)                   : Device EUI     
791 791  
792 -AT+RXDL  : Extend the sending and receiving time
1017 +(% style="background-color:#dcdcdc" %)**AT+NWKID**(%%)               : Network ID (You can enter this command change only after successful network connection) 
793 793  
794 -AT+CNTFAC  : Get or set counting parameters
1019 +(% style="background-color:#dcdcdc" %)**AT+NWKSKEY**(%%)          : Network Session Key Joining and sending date on LoRa network  
795 795  
796 -AT+SERVADDR  : Server Address
1021 +(% style="background-color:#dcdcdc" %)**AT+CFM**(%%)  : Confirm Mode       
797 797  
1023 +(% style="background-color:#dcdcdc" %)**AT+CFS**(%%)                     : Confirm Status       
798 798  
799 -(% style="color:#037691" %)**COAP Management**      
1025 +(% style="background-color:#dcdcdc" %)**AT+JOIN**(%%)  : Join LoRa? Network       
800 800  
801 -AT+URI            : Resource parameters
1027 +(% style="background-color:#dcdcdc" %)**AT+NJM**(%%)  : LoRa? Network Join Mode    
802 802  
1029 +(% style="background-color:#dcdcdc" %)**AT+NJS**(%%)                     : LoRa? Network Join Status    
803 803  
804 -(% style="color:#037691" %)**UDP Management**
1031 +(% style="background-color:#dcdcdc" %)**AT+RECV**(%%)                  : Print Last Received Data in Raw Format
805 805  
806 -AT+CFM          : Upload confirmation mode (only valid for UDP)
1033 +(% style="background-color:#dcdcdc" %)**AT+RECVB**(%%)                : Print Last Received Data in Binary Format      
807 807  
1035 +(% style="background-color:#dcdcdc" %)**AT+SEND**(%%)                  : Send Text Data      
808 808  
809 -(% style="color:#037691" %)**MQTT Management**
1037 +(% style="background-color:#dcdcdc" %)**AT+SENB**(%%)                  : Send Hexadecimal Data
810 810  
811 -AT+CLIENT               : Get or Set MQTT client
812 812  
813 -AT+UNAME  : Get or Set MQTT Username
1040 +(% style="color:#037691" %)**LoRa Network Management**
814 814  
815 -AT+PWD                  : Get or Set MQTT password
1042 +(% style="background-color:#dcdcdc" %)**AT+ADR**(%%)          : Adaptive Rate
816 816  
817 -AT+PUBTOPIC  : Get or Set MQTT publish topic
1044 +(% style="background-color:#dcdcdc" %)**AT+CLASS**(%%)  : LoRa Class(Currently only support class A
818 818  
819 -AT+SUBTOPIC  : Get or Set MQTT subscription topic
1046 +(% style="background-color:#dcdcdc" %)**AT+DCS**(%%)  : Duty Cycle Setting 
820 820  
1048 +(% style="background-color:#dcdcdc" %)**AT+DR**(%%)  : Data Rate (Can Only be Modified after ADR=0)     
821 821  
822 -(% style="color:#037691" %)**Information**          
1050 +(% style="background-color:#dcdcdc" %)**AT+FCD**(%%)  : Frame Counter Downlink       
823 823  
824 -AT+FDR  : Factory Data Reset
1052 +(% style="background-color:#dcdcdc" %)**AT+FCU**(%%)  : Frame Counter Uplink   
825 825  
826 -AT+PWORD  : Serial Access Password
1054 +(% style="background-color:#dcdcdc" %)**AT+JN1DL**(%%)  : Join Accept Delay1
827 827  
1056 +(% style="background-color:#dcdcdc" %)**AT+JN2DL**(%%)  : Join Accept Delay2
828 828  
1058 +(% style="background-color:#dcdcdc" %)**AT+PNM**(%%)  : Public Network Mode   
829 829  
830 -= ​5.  FAQ =
1060 +(% style="background-color:#dcdcdc" %)**AT+RX1DL**(%%)  : Receive Delay1      
831 831  
832 -== 5.1 ​ How to Upgrade Firmware ==
1062 +(% style="background-color:#dcdcdc" %)**AT+RX2DL**(%%)  : Receive Delay2      
833 833  
1064 +(% style="background-color:#dcdcdc" %)**AT+RX2DR**(%%)  : Rx2 Window Data Rate 
834 834  
1066 +(% style="background-color:#dcdcdc" %)**AT+RX2FQ**(%%)  : Rx2 Window Frequency
1067 +
1068 +(% style="background-color:#dcdcdc" %)**AT+TXP**(%%)  : Transmit Power
1069 +
1070 +(% style="background-color:#dcdcdc" %)**AT+ MOD**(%%)  : Set work mode
1071 +
1072 +
1073 +(% style="color:#037691" %)**Information** 
1074 +
1075 +(% style="background-color:#dcdcdc" %)**AT+RSSI**(%%)           : RSSI of the Last Received Packet   
1076 +
1077 +(% style="background-color:#dcdcdc" %)**AT+SNR**(%%)           : SNR of the Last Received Packet   
1078 +
1079 +(% style="background-color:#dcdcdc" %)**AT+VER**(%%)           : Image Version and Frequency Band       
1080 +
1081 +(% style="background-color:#dcdcdc" %)**AT+FDR**(%%)           : Factory Data Reset
1082 +
1083 +(% style="background-color:#dcdcdc" %)**AT+PORT**(%%)  : Application Port    
1084 +
1085 +(% style="background-color:#dcdcdc" %)**AT+CHS**(%%)  : Get or Set Frequency (Unit: Hz) for Single Channel Mode
1086 +
1087 + (% style="background-color:#dcdcdc" %)**AT+CHE**(%%)  : Get or Set eight channels mode, Only for US915, AU915, CN470
1088 +
1089 +
1090 += ​4. FAQ =
1091 +
1092 +== 4.1 ​How to change the LoRa Frequency Bands/Region? ==
1093 +
835 835  (((
836 -User can upgrade the firmware for 1) bug fix, 2) new feature release.
1095 +You can follow the instructions for [[how to upgrade image>>||anchor="H2.10200BFirmwareChangeLog"]].
1096 +When downloading the images, choose the required image file for download. ​
837 837  )))
838 838  
839 839  (((
840 -Please see this link for how to upgrade:  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList>>http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList]]
1100 +
841 841  )))
842 842  
843 843  (((
844 -(% style="color:red" %)Notice, NSE01 and LSE01 share the same mother board. They use the same connection and method to update.
1104 +How to set up LSE01 to work in 8 channel mode By default, the frequency bands US915, AU915, CN470 work in 72 frequencies. Many gateways are 8 channel gateways, and in this case, the OTAA join time and uplink schedule is long and unpredictable while the end node is hopping in 72 frequencies.
845 845  )))
846 846  
1107 +(((
1108 +
1109 +)))
847 847  
1111 +(((
1112 +You can configure the end node to work in 8 channel mode by using the AT+CHE command. The 500kHz channels are always included for OTAA.
1113 +)))
848 848  
849 -= 6.  Trouble Shooting =
1115 +(((
1116 +
1117 +)))
850 850  
851 -== 6.1  ​Connection problem when uploading firmware ==
1119 +(((
1120 +For example, in **US915** band, the frequency table is as below. By default, the end node will use all channels (0~~71) for OTAA Join process. After the OTAA Join, the end node will use these all channels (0~~71) to send uplink packets.
1121 +)))
852 852  
1123 +[[image:image-20220606154726-3.png]]
853 853  
854 -(% class="wikigeneratedid" %)
1125 +
1126 +When you use the TTN network, the US915 frequency bands use are:
1127 +
1128 +* 903.9 - SF7BW125 to SF10BW125
1129 +* 904.1 - SF7BW125 to SF10BW125
1130 +* 904.3 - SF7BW125 to SF10BW125
1131 +* 904.5 - SF7BW125 to SF10BW125
1132 +* 904.7 - SF7BW125 to SF10BW125
1133 +* 904.9 - SF7BW125 to SF10BW125
1134 +* 905.1 - SF7BW125 to SF10BW125
1135 +* 905.3 - SF7BW125 to SF10BW125
1136 +* 904.6 - SF8BW500
1137 +
855 855  (((
856 -(% style="font-size:14px" %)**Please see: **(%%)[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting>>http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting||style="background-color: rgb(255, 255, 255); font-size: 14px;"]]
1139 +Because the end node is now hopping in 72 frequency, it makes it difficult for the devices to Join the TTN network and uplink data. To solve this issue, you can access the device via the AT commands and run:
1140 +
1141 +* (% style="color:#037691" %)**AT+CHE=2**
1142 +* (% style="color:#037691" %)**ATZ**
857 857  )))
858 858  
1145 +(((
1146 +
859 859  
1148 +to set the end node to work in 8 channel mode. The device will work in Channel 8-15 & 64-71 for OTAA, and channel 8-15 for Uplink.
1149 +)))
860 860  
861 -== 6.2  AT Command input doesn't work ==
1151 +(((
1152 +
1153 +)))
862 862  
863 863  (((
1156 +The **AU915** band is similar. Below are the AU915 Uplink Channels.
1157 +)))
1158 +
1159 +[[image:image-20220606154825-4.png]]
1160 +
1161 +
1162 +== 4.2 ​Can I calibrate LSE01 to different soil types? ==
1163 +
1164 +LSE01 is calibrated for saline-alkali soil and loamy soil. If users want to use it for other soil, they can calibrate the value in the IoT platform base on the value measured by saline-alkali soil and loamy soil. The formula can be found at [[this link>>https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/&file=Calibrate_to_other_Soil_20220605.pdf]].
1165 +
1166 +
1167 += 5. Trouble Shooting =
1168 +
1169 +== 5.1 ​Why I can't join TTN in US915 / AU915 bands? ==
1170 +
1171 +It is due to channel mapping. Please see the [[Eight Channel Mode>>doc:Main.End Device AT Commands and Downlink Command.WebHome||anchor="H7.19EightChannelMode"]] section above for details.
1172 +
1173 +
1174 +== 5.2 AT Command input doesn't work ==
1175 +
1176 +(((
864 864  In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
865 865  )))
866 866  
867 867  
1181 +== 5.3 Device rejoin in at the second uplink packet ==
868 868  
869 -= 7. ​ Order Info =
1183 +(% style="color:#4f81bd" %)**Issue describe as below:**
870 870  
1185 +[[image:1654500909990-784.png]]
871 871  
872 -Part Number**:** (% style="color:#4f81bd" %)**NSE01**
873 873  
1188 +(% style="color:#4f81bd" %)**Cause for this issue:**
874 874  
1190 +(((
1191 +The fuse on LSE01 is not large enough, some of the soil probe require large current up to 5v 800mA, in a short pulse. When this happen, it cause the device reboot so user see rejoin.
1192 +)))
1193 +
1194 +
1195 +(% style="color:#4f81bd" %)**Solution: **
1196 +
1197 +All new shipped LSE01 after 2020-May-30 will have this to fix. For the customer who see this issue, please bypass the fuse as below:
1198 +
1199 +[[image:1654500929571-736.png||height="458" width="832"]]
1200 +
1201 +
1202 += 6. ​Order Info =
1203 +
1204 +
1205 +Part Number**:** (% style="color:#4f81bd" %)**LSE01-XX-YY**
1206 +
1207 +
1208 +(% style="color:#4f81bd" %)**XX**(%%)**:** The default frequency band
1209 +
1210 +* (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band
1211 +* (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band
1212 +* (% style="color:red" %)**EU433**(%%): LoRaWAN EU433 band
1213 +* (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band
1214 +* (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band
1215 +* (% style="color:red" %)**US915**(%%): LoRaWAN US915 band
1216 +* (% style="color:red" %)**IN865**(%%):  LoRaWAN IN865 band
1217 +* (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
1218 +
1219 +(% style="color:#4f81bd" %)**YY**(%%)**: **Battery Option
1220 +
1221 +* (% style="color:red" %)**4**(%%): 4000mAh battery
1222 +* (% style="color:red" %)**8**(%%): 8500mAh battery
1223 +
875 875  (% class="wikigeneratedid" %)
876 876  (((
877 877  
878 878  )))
879 879  
880 -= 8.  Packing Info =
1229 += 7. Packing Info =
881 881  
882 882  (((
883 883  
884 884  
885 885  (% style="color:#037691" %)**Package Includes**:
1235 +)))
886 886  
887 -
888 -* NSE01 NB-IoT Soil Moisture & EC Sensor x 1
889 -* External antenna x 1
1237 +* (((
1238 +LSE01 LoRaWAN Soil Moisture & EC Sensor x 1
890 890  )))
891 891  
892 892  (((
... ... @@ -893,20 +893,24 @@
893 893  
894 894  
895 895  (% style="color:#037691" %)**Dimension and weight**:
1245 +)))
896 896  
897 -
898 -* Size: 195 x 125 x 55 mm
899 -* Weight:   420g
1247 +* (((
1248 +Device Size: cm
900 900  )))
1250 +* (((
1251 +Device Weight: g
1252 +)))
1253 +* (((
1254 +Package Size / pcs : cm
1255 +)))
1256 +* (((
1257 +Weight / pcs : g
901 901  
902 -(((
903 903  
904 -
905 -
906 -
907 907  )))
908 908  
909 -= 9.  Support =
1262 += 8. Support =
910 910  
911 911  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
912 912  * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]
1657260785982-288.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -138.2 KB
Content
1657261119050-993.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -126.1 KB
Content
1657261278785-153.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -126.1 KB
Content
image-20220708140453-6.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -132.7 KB
Content
image-20220708141352-7.jpeg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -102.7 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0