Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -20,7 +20,6 @@
20	20
21	21
22	22
23		-
24	24	= 1.  Introduction =
25	25
26	26	== 1.1 ​ What is LoRaWAN Soil Moisture & EC Sensor ==
...	...	@@ -28,21 +28,13 @@
28	28	(((
29	29
30	30
31		-(((
32	32	Dragino NSE01 is an (% style="color:blue" %)**NB-IOT soil moisture & EC sensor**(%%) for agricultural IoT. Used to measure the soil moisture of saline-alkali soil and loam. The soil sensor uses the FDR method to calculate soil moisture and compensates it with soil temperature and electrical conductivity. It has also been calibrated for mineral soil types at the factory.
33		-)))
34	34
35		-(((
36	36	It can detect (% style="color:blue" %)**Soil Moisture, Soil Temperature and Soil Conductivity**(%%), and upload its value to the server wirelessly.
37		-)))
38	38
39		-(((
40	40	The wireless technology used in NSE01 allows the device to send data at a low data rate and reach ultra-long distances, providing ultra-long-distance spread spectrum Communication.
41		-)))
42	42
43		-(((
44	44	NSE01 are powered by (% style="color:blue" %)**8500mAh Li-SOCI2**(%%) batteries, which can be used for up to 5 years.
45		-)))
46	46
47	47
48	48	)))
...	...	@@ -69,6 +69,7 @@
69	69	* Micro SIM card slot for NB-IoT SIM
70	70	* 8500mAh Battery for long term use
71	71
	63	+
72	72	== 1.3  Specification ==
73	73
74	74
...	...	@@ -136,9 +136,7 @@
136	136	=== 2.2.1 Test Requirement ===
137	137
138	138
139		-(((
140	140	To use NSE01 in your city, make sure meet below requirements:
141		-)))
142	142
143	143	* Your local operator has already distributed a NB-IoT Network there.
144	144	* The local NB-IoT network used the band that NSE01 supports.
...	...	@@ -155,13 +155,9 @@
155	155
156	156	=== 2.2.2 Insert SIM card ===
157	157
158		-(((
159	159	Insert the NB-IoT Card get from your provider.
160		-)))
161	161
162		-(((
163	163	User need to take out the NB-IoT module and insert the SIM card like below:
164		-)))
165	165
166	166
167	167	[[image:1657249468462-536.png]]
...	...	@@ -200,9 +200,7 @@
200	200
201	201	[[image:image-20220708110657-3.png]]
202	202
203		-(((
204	204	(% style="color:red" %)Note: the valid AT Commands can be found at: (%%)[[http:~~/~~/www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/]]
205		-)))
206	206
207	207
208	208
...	...	@@ -305,14 +305,12 @@
305	305	In this mode, uplink payload includes in total 18 bytes
306	306
307	307	(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:510px" %)
308		-|=(% style="width: 60px;" %)(((
	292	+|=(% style="width: 50px;" %)(((
309	309	**Size(bytes)**
310		-)))|=(% style="width: 50px;" %)**6**|=(% style="width: 25px;" %)2|=(% style="width: 25px;" %)**2**|=(% style="width: 70px;" %)**1**|=(% style="width: 60px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 90px;" %)**2**|=(% style="width: 50px;" %)**1**
	294	+)))|=(% style="width: 50px;" %)**6**|=(% style="width: 25px;" %)2|=(% style="width: 25px;" %)**2**|=(% style="width: 80px;" %)**1**|=(% style="width: 80px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 40px;" %)**1**
311	311	|(% style="width:97px" %)**Value**|(% style="width:83px" %)[[Device ID>>||anchor="H2.4.1A0A0DeviceID"]]|(% style="width:41px" %)[[Ver>>||anchor="H2.4.2A0VersionInfo"]]|(% style="width:46px" %)[[BAT>>||anchor="H2.4.3A0BatteryInfo"]]|(% style="width:123px" %)[[Signal Strength>>||anchor="H2.4.4A0SignalStrength"]]|(% style="width:108px" %)[[Soil Moisture>>||anchor="H2.4.5A0SoilMoisture"]]|(% style="width:133px" %)[[Soil Temperature>>||anchor="H2.4.6A0SoilTemperature"]]|(% style="width:159px" %)[[Soil Conductivity(EC)>>||anchor="H2.4.7A0SoilConductivity28EC29"]]|(% style="width:80px" %)[[Interrupt>>||anchor="H2.4.8A0DigitalInterrupt"]]
312	312
313		-(((
314	314	If we use the MQTT client to subscribe to this MQTT topic, we can see the following information when the NSE01 uplink data.
315		-)))
316	316
317	317
318	318	[[image:image-20220708111918-4.png]]
...	...	@@ -333,44 +333,28 @@
333	333	* Interrupt: 0x00 = 0
334	334
335	335
336		-
337		-
338	338	== 2.4  Payload Explanation and Sensor Interface ==
339	339
340	340
341	341	=== 2.4.1  Device ID ===
342	342
343		-(((
344	344	By default, the Device ID equal to the last 6 bytes of IMEI.
345		-)))
346	346
347		-(((
348	348	User can use (% style="color:blue" %)**AT+DEUI**(%%) to set Device ID
349		-)))
350	350
351		-(((
352	352	**Example:**
353		-)))
354	354
355		-(((
356	356	AT+DEUI=A84041F15612
357		-)))
358	358
359		-(((
360	360	The Device ID is stored in a none-erase area, Upgrade the firmware or run AT+FDR won't erase Device ID.
361		-)))
362	362
363	363
364	364
365	365	=== 2.4.2  Version Info ===
366	366
367		-(((
368	368	Specify the software version: 0x64=100, means firmware version 1.00.
369		-)))
370	370
371		-(((
372	372	For example: 0x00 64 : this device is NSE01 with firmware version 1.0.0.
373		-)))
374	374
375	375
376	376
...	...	@@ -392,33 +392,19 @@
392	392
393	393	=== 2.4.4  Signal Strength ===
394	394
395		-(((
396	396	NB-IoT Network signal Strength.
397		-)))
398	398
399		-(((
400	400	**Ex1: 0x1d = 29**
401		-)))
402	402
403		-(((
404	404	(% style="color:blue" %)**0**(%%)  -113dBm or less
405		-)))
406	406
407		-(((
408	408	(% style="color:blue" %)**1**(%%)  -111dBm
409		-)))
410	410
411		-(((
412	412	(% style="color:blue" %)**2...30**(%%) -109dBm... -53dBm
413		-)))
414	414
415		-(((
416	416	(% style="color:blue" %)**31**  (%%) -51dBm or greater
417		-)))
418	418
419		-(((
420	420	(% style="color:blue" %)**99**   (%%) Not known or not detectable
421		-)))
422	422
423	423
424	424
...	...	@@ -425,16 +425,12 @@
425	425	=== 2.4.5  Soil Moisture ===
426	426
427	427	(((
428		-(((
429	429	Get the moisture content of the soil. The value range of the register is 0-10000(Decimal), divide this value by 100 to get the percentage of moisture in the soil.
430	430	)))
431		-)))
432	432
433	433	(((
434		-(((
435	435	For example, if the data you get from the register is **__0x05 0xDC__**, the moisture content in the soil is
436	436	)))
437		-)))
438	438
439	439	(((
440	440
...	...	@@ -449,7 +449,7 @@
449	449	=== 2.4.6  Soil Temperature ===
450	450
451	451	(((
452		-Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is __**0x09 0xEC**__, the temperature content in the soil is
	400	+ Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is __**0x09 0xEC**__, the temperature content in the soil is
453	453	)))
454	454
455	455	(((
...	...	@@ -490,56 +490,34 @@
490	490
491	491	=== 2.4.8  Digital Interrupt ===
492	492
493		-(((
494	494	Digital Interrupt refers to pin (% style="color:blue" %)**GPIO_EXTI**(%%), and there are different trigger methods. When there is a trigger, the NSE01 will send a packet to the server.
495		-)))
496	496
497		-(((
498	498	The command is:
499		-)))
500	500
501		-(((
502	502	(% style="color:blue" %)**AT+INTMOD=3 **(%%) ~/~/(more info about INMOD please refer [[**AT Command Manual**>>url:https://www.dragino.com/downloads/downloads/NB-IoT/NBSN95/DRAGINO_NBSN95-NB_AT%20Commands_v1.1.0.pdf]])**.**
503		-)))
504	504
505	505
506		-(((
507	507	The lower four bits of this data field shows if this packet is generated by interrupt or not. Click here for the hardware and software set up.
508		-)))
509	509
510	510
511		-(((
512	512	Example:
513		-)))
514	514
515		-(((
516	516	0x(00): Normal uplink packet.
517		-)))
518	518
519		-(((
520	520	0x(01): Interrupt Uplink Packet.
521		-)))
522	522
523	523
524	524
525	525	=== 2.4.9  ​+5V Output ===
526	526
527		-(((
528	528	NSE01 will enable +5V output before all sampling and disable the +5v after all sampling.
529		-)))
530	530
531	531
532		-(((
533	533	The 5V output time can be controlled by AT Command.
534		-)))
535	535
536		-(((
537	537	(% style="color:blue" %)**AT+5VT=1000**
538		-)))
539	539
540		-(((
541	541	Means set 5V valid time to have 1000ms. So the real 5V output will actually have 1000ms + sampling time for other sensors.
542		-)))
543	543
544	544
545	545
...	...	@@ -589,9 +589,7 @@
589	589
590	590	* (% style="color:blue" %)**INTMOD**
591	591
592		-(((
593	593	Downlink Payload: 06000003, Set AT+INTMOD=3
594		-)))
595	595
596	596
597	597