Summary

• Page properties (1 modified, 0 added, 0 removed)
• Attachments (0 modified, 0 added, 7 removed)
  • 1657259653666-883.png
  • 1657260785982-288.png
  • 1657261119050-993.png
  • 1657261278785-153.png
  • image-20220708133731-5.png
  • image-20220708140453-6.png
  • image-20220708141352-7.jpeg

Details

Page properties

Content

...	...	@@ -13,14 +13,11 @@
13	13
14	14	**Table of Contents:**
15	15
16		-{{toc/}}
17	17
18	18
19	19
20	20
21	21
22		-
23		-
24	24	= 1.  Introduction =
25	25
26	26	== 1.1 ​ What is LoRaWAN Soil Moisture & EC Sensor ==
...	...	@@ -28,21 +28,13 @@
28	28	(((
29	29
30	30
31		-(((
32	32	Dragino NSE01 is an (% style="color:blue" %)**NB-IOT soil moisture & EC sensor**(%%) for agricultural IoT. Used to measure the soil moisture of saline-alkali soil and loam. The soil sensor uses the FDR method to calculate soil moisture and compensates it with soil temperature and electrical conductivity. It has also been calibrated for mineral soil types at the factory.
33		-)))
34	34
35		-(((
36	36	It can detect (% style="color:blue" %)**Soil Moisture, Soil Temperature and Soil Conductivity**(%%), and upload its value to the server wirelessly.
37		-)))
38	38
39		-(((
40	40	The wireless technology used in NSE01 allows the device to send data at a low data rate and reach ultra-long distances, providing ultra-long-distance spread spectrum Communication.
41		-)))
42	42
43		-(((
44	44	NSE01 are powered by (% style="color:blue" %)**8500mAh Li-SOCI2**(%%) batteries, which can be used for up to 5 years.
45		-)))
46	46
47	47
48	48	)))
...	...	@@ -54,8 +54,9 @@
54	54
55	55
56	56
57		-== 1.2 ​ Features ==
	46	+== 1.2 ​Features ==
58	58
	48	+
59	59	* NB-IoT Bands: B1/B3/B8/B5/B20/B28 @H-FDD
60	60	* Monitor Soil Moisture
61	61	* Monitor Soil Temperature
...	...	@@ -86,7 +86,7 @@
86	86	* - B20 @H-FDD: 800MHz
87	87	* - B28 @H-FDD: 700MHz
88	88
89		-Probe(% style="color:#037691" %)** Specification:**
	79	+(% style="color:#037691" %)**Probe Specification:**
90	90
91	91	Measure Volume: Base on the centra pin of the probe, a cylinder with 7cm diameter and 10cm height.
92	92
...	...	@@ -136,9 +136,7 @@
136	136	=== 2.2.1 Test Requirement ===
137	137
138	138
139		-(((
140	140	To use NSE01 in your city, make sure meet below requirements:
141		-)))
142	142
143	143	* Your local operator has already distributed a NB-IoT Network there.
144	144	* The local NB-IoT network used the band that NSE01 supports.
...	...	@@ -155,13 +155,9 @@
155	155
156	156	=== 2.2.2 Insert SIM card ===
157	157
158		-(((
159	159	Insert the NB-IoT Card get from your provider.
160		-)))
161	161
162		-(((
163	163	User need to take out the NB-IoT module and insert the SIM card like below:
164		-)))
165	165
166	166
167	167	[[image:1657249468462-536.png]]
...	...	@@ -200,9 +200,7 @@
200	200
201	201	[[image:image-20220708110657-3.png]]
202	202
203		-(((
204	204	(% style="color:red" %)Note: the valid AT Commands can be found at: (%%)[[http:~~/~~/www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/]]
205		-)))
206	206
207	207
208	208
...	...	@@ -305,14 +305,12 @@
305	305	In this mode, uplink payload includes in total 18 bytes
306	306
307	307	(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:510px" %)
308		-|=(% style="width: 60px;" %)(((
	290	+|=(% style="width: 50px;" %)(((
309	309	**Size(bytes)**
310		-)))|=(% style="width: 50px;" %)**6**|=(% style="width: 25px;" %)2|=(% style="width: 25px;" %)**2**|=(% style="width: 70px;" %)**1**|=(% style="width: 60px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 90px;" %)**2**|=(% style="width: 50px;" %)**1**
311		-|(% style="width:97px" %)**Value**|(% style="width:83px" %)[[Device ID>>||anchor="H2.4.1A0A0DeviceID"]]|(% style="width:41px" %)[[Ver>>||anchor="H2.4.2A0VersionInfo"]]|(% style="width:46px" %)[[BAT>>||anchor="H2.4.3A0BatteryInfo"]]|(% style="width:123px" %)[[Signal Strength>>||anchor="H2.4.4A0SignalStrength"]]|(% style="width:108px" %)[[Soil Moisture>>||anchor="H2.4.5A0SoilMoisture"]]|(% style="width:133px" %)[[Soil Temperature>>||anchor="H2.4.6A0SoilTemperature"]]|(% style="width:159px" %)[[Soil Conductivity(EC)>>||anchor="H2.4.7A0SoilConductivity28EC29"]]|(% style="width:80px" %)[[Interrupt>>||anchor="H2.4.8A0DigitalInterrupt"]]
	292	+)))|=(% style="width: 50px;" %)**6**|=(% style="width: 25px;" %)2|=(% style="width: 25px;" %)**2**|=(% style="width: 80px;" %)**1**|=(% style="width: 80px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 40px;" %)**1**
	293	+|(% style="width:97px" %)**Value**|(% style="width:83px" %)[[Device ID>>||anchor="H"]]|(% style="width:41px" %)[[Ver>>||anchor="H"]]|(% style="width:46px" %)[[BAT>>||anchor="H"]]|(% style="width:123px" %)[[Signal Strength>>||anchor="H"]]|(% style="width:108px" %)[[Soil Moisture>>||anchor="H"]]|(% style="width:133px" %)[[Soil Temperature>>||anchor="H"]]|(% style="width:159px" %)[[Soil Conductivity(EC)>>||anchor="H"]]|(% style="width:80px" %)[[Interrupt>>||anchor="H"]]
312	312
313		-(((
314	314	If we use the MQTT client to subscribe to this MQTT topic, we can see the following information when the NSE01 uplink data.
315		-)))
316	316
317	317
318	318	[[image:image-20220708111918-4.png]]
...	...	@@ -333,44 +333,28 @@
333	333	* Interrupt: 0x00 = 0
334	334
335	335
336		-
337		-
338	338	== 2.4  Payload Explanation and Sensor Interface ==
339	339
340	340
341	341	=== 2.4.1  Device ID ===
342	342
343		-(((
344	344	By default, the Device ID equal to the last 6 bytes of IMEI.
345		-)))
346	346
347		-(((
348	348	User can use (% style="color:blue" %)**AT+DEUI**(%%) to set Device ID
349		-)))
350	350
351		-(((
352	352	**Example:**
353		-)))
354	354
355		-(((
356	356	AT+DEUI=A84041F15612
357		-)))
358	358
359		-(((
360	360	The Device ID is stored in a none-erase area, Upgrade the firmware or run AT+FDR won't erase Device ID.
361		-)))
362	362
363	363
364	364
365	365	=== 2.4.2  Version Info ===
366	366
367		-(((
368	368	Specify the software version: 0x64=100, means firmware version 1.00.
369		-)))
370	370
371		-(((
372	372	For example: 0x00 64 : this device is NSE01 with firmware version 1.0.0.
373		-)))
374	374
375	375
376	376
...	...	@@ -392,33 +392,19 @@
392	392
393	393	=== 2.4.4  Signal Strength ===
394	394
395		-(((
396	396	NB-IoT Network signal Strength.
397		-)))
398	398
399		-(((
400	400	**Ex1: 0x1d = 29**
401		-)))
402	402
403		-(((
404	404	(% style="color:blue" %)**0**(%%)  -113dBm or less
405		-)))
406	406
407		-(((
408	408	(% style="color:blue" %)**1**(%%)  -111dBm
409		-)))
410	410
411		-(((
412	412	(% style="color:blue" %)**2...30**(%%) -109dBm... -53dBm
413		-)))
414	414
415		-(((
416	416	(% style="color:blue" %)**31**  (%%) -51dBm or greater
417		-)))
418	418
419		-(((
420	420	(% style="color:blue" %)**99**   (%%) Not known or not detectable
421		-)))
422	422
423	423
424	424
...	...	@@ -425,16 +425,12 @@
425	425	=== 2.4.5  Soil Moisture ===
426	426
427	427	(((
428		-(((
429	429	Get the moisture content of the soil. The value range of the register is 0-10000(Decimal), divide this value by 100 to get the percentage of moisture in the soil.
430	430	)))
431		-)))
432	432
433	433	(((
434		-(((
435	435	For example, if the data you get from the register is **__0x05 0xDC__**, the moisture content in the soil is
436	436	)))
437		-)))
438	438
439	439	(((
440	440
...	...	@@ -449,7 +449,7 @@
449	449	=== 2.4.6  Soil Temperature ===
450	450
451	451	(((
452		-Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is __**0x09 0xEC**__, the temperature content in the soil is
	398	+ Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is __**0x09 0xEC**__, the temperature content in the soil is
453	453	)))
454	454
455	455	(((
...	...	@@ -490,66 +490,52 @@
490	490
491	491	=== 2.4.8  Digital Interrupt ===
492	492
493		-(((
494	494	Digital Interrupt refers to pin (% style="color:blue" %)**GPIO_EXTI**(%%), and there are different trigger methods. When there is a trigger, the NSE01 will send a packet to the server.
495		-)))
496	496
497		-(((
498	498	The command is:
499		-)))
500	500
501		-(((
502	502	(% style="color:blue" %)**AT+INTMOD=3 **(%%) ~/~/(more info about INMOD please refer [[**AT Command Manual**>>url:https://www.dragino.com/downloads/downloads/NB-IoT/NBSN95/DRAGINO_NBSN95-NB_AT%20Commands_v1.1.0.pdf]])**.**
503		-)))
504	504
505	505
506		-(((
507		-The lower four bits of this data field shows if this packet is generated by interrupt or not. Click here for the hardware and software set up.
508		-)))
	446	+The lower four bits of this data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H"]] for the hardware and software set up.
509	509
510	510
511		-(((
512	512	Example:
513		-)))
514	514
515		-(((
516	516	0x(00): Normal uplink packet.
517		-)))
518	518
519		-(((
520	520	0x(01): Interrupt Uplink Packet.
521		-)))
522	522
523	523
524	524
	457	+
525	525	=== 2.4.9  ​+5V Output ===
526	526
527		-(((
	460	+
528	528	NSE01 will enable +5V output before all sampling and disable the +5v after all sampling.
529		-)))
530	530
531	531
532		-(((
533	533	The 5V output time can be controlled by AT Command.
534		-)))
535	535
536		-(((
537	537	(% style="color:blue" %)**AT+5VT=1000**
538		-)))
539	539
540		-(((
541	541	Means set 5V valid time to have 1000ms. So the real 5V output will actually have 1000ms + sampling time for other sensors.
542		-)))
543	543
544	544
545	545
546		-== 2.5  Downlink Payload ==
	472	+== 2.4 Uplink Interval ==
547	547
548		-By default, NSE01 prints the downlink payload to console port.
	474	+The LSE01 by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link: [[Change Uplink Interval>>doc:Main.End Device AT Commands and Downlink Command.WebHome||anchor="H4.1ChangeUplinkInterval"]]
549	549
550		-[[image:image-20220708133731-5.png]]
551	551
552	552
	478	+== 2.5 Downlink Payload ==
	479	+
	480	+By default, LSE50 prints the downlink payload to console port.
	481	+
	482	+[[image:image-20220606165544-8.png]]
	483	+
	484	+
553	553	(((
554	554	(% style="color:blue" %)**Examples:**
555	555	)))
...	...	@@ -563,7 +563,7 @@
563	563	)))
564	564
565	565	(((
566		-If the payload=0100003C, it means set the END Node's TDC to 0x00003C=60(S), while type code is 01.
	498	+If the payload=0100003C, it means set the END Node’s TDC to 0x00003C=60(S), while type code is 01.
567	567	)))
568	568
569	569	(((
...	...	@@ -583,300 +583,734 @@
583	583	)))
584	584
585	585	(((
586		-If payload = 0x04FF, it will reset the NSE01
	518	+If payload = 0x04FF, it will reset the LSE01
587	587	)))
588	588
589	589
590		-* (% style="color:blue" %)**INTMOD**
	522	+* (% style="color:blue" %)**CFM**
591	591
592		-Downlink Payload: 06000003, Set AT+INTMOD=3
	524	+Downlink Payload: 05000001, Set AT+CFM=1 or 05000000 , set AT+CFM=0
593	593
594	594
595	595
596		-== 2.6  ​LED Indicator ==
	528	+== 2.6 ​Show Data in DataCake IoT Server ==
597	597
598	598	(((
599		-The NSE01 has an internal LED which is to show the status of different state.
	531	+[[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:
	532	+)))
600	600
	534	+(((
	535	+
	536	+)))
601	601
602		-* When power on, NSE01 will detect if sensor probe is connected, if probe detected, LED will blink four times. (no blinks in this step is no probe)
603		-* Then the LED will be on for 1 second means device is boot normally.
604		-* After NSE01 join NB-IoT network. The LED will be ON for 3 seconds.
605		-* For each uplink probe, LED will be on for 500ms.
	538	+(((
	539	+(% style="color:blue" %)**Step 1**(%%):  Be sure that your device is programmed and properly connected to the network at this time.
606	606	)))
607	607
	542	+(((
	543	+(% style="color:blue" %)**Step 2**(%%):  To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:
	544	+)))
608	608
609	609
	547	+[[image:1654505857935-743.png]]
610	610
611		-== 2.7  Installation in Soil ==
612	612
613		-__**Measurement the soil surface**__
	550	+[[image:1654505874829-548.png]]
614	614
615		-Choose the proper measuring position. Avoid the probe to touch rocks or hard things. Split the surface soil according to the measured deep. Keep the measured as original density. Vertical insert the probe into the soil to be measured. Make sure not shake when inserting. [[https:~~/~~/img.alicdn.com/imgextra/i3/2005165265/O1CN010rj9Oh1olPsQxrdUK_!!2005165265.jpg>>url:https://img.alicdn.com/imgextra/i3/2005165265/O1CN010rj9Oh1olPsQxrdUK_!!2005165265.jpg]]
616	616
617		-[[image:1657259653666-883.png]] ​
	553	+(% style="color:blue" %)**Step 3**(%%)**:**  Create an account or log in Datacake.
618	618
	555	+(% style="color:blue" %)**Step 4**(%%)**:**  Search the LSE01 and add DevEUI.
619	619
620		-(((
621		-
622	622
623		-(((
624		-Dig a hole with diameter > 20CM.
625		-)))
	558	+[[image:1654505905236-553.png]]
626	626
627		-(((
628		-Horizontal insert the probe to the soil and fill the hole for long term measurement.
629		-)))
630		-)))
631	631
632		-[[image:1654506665940-119.png]]
	561	+After added, the sensor data arrive TTN, it will also arrive and show in Mydevices.
633	633
634		-(((
635		-
636		-)))
	563	+[[image:1654505925508-181.png]]
637	637
638	638
639		-== 2.8  ​Firmware Change Log ==
640	640
	567	+== 2.7 Frequency Plans ==
641	641
642		-Download URL & Firmware Change log
	569	+The LSE01 uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
643	643
644		-[[www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/Firmware/]]
645	645
	572	+=== 2.7.1 EU863-870 (EU868) ===
646	646
647		-Upgrade Instruction: [[Upgrade_Firmware>>||anchor="H5.1200BHowtoUpgradeFirmware"]]
	574	+(% style="color:#037691" %)** Uplink:**
648	648
	576	+868.1 - SF7BW125 to SF12BW125
649	649
	578	+868.3 - SF7BW125 to SF12BW125 and SF7BW250
650	650
651		-== 2.9  ​Battery Analysis ==
	580	+868.5 - SF7BW125 to SF12BW125
652	652
653		-=== 2.9.1  ​Battery Type ===
	582	+867.1 - SF7BW125 to SF12BW125
654	654
	584	+867.3 - SF7BW125 to SF12BW125
655	655
656		-The NSE01 battery is a combination of an 8500mAh Li/SOCI2 Battery and a Super Capacitor. The battery is none-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
	586	+867.5 - SF7BW125 to SF12BW125
657	657
	588	+867.7 - SF7BW125 to SF12BW125
658	658
659		-The battery is designed to last for several years depends on the actually use environment and update interval.
	590	+867.9 - SF7BW125 to SF12BW125
660	660
	592	+868.8 - FSK
661	661
662		-The battery related documents as below:
663	663
664		-* [[Battery Dimension>>http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
665		-* [[Lithium-Thionyl Chloride Battery datasheet>>http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
666		-* [[Lithium-ion Battery-Capacitor datasheet>>http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
	595	+(% style="color:#037691" %)** Downlink:**
667	667
	597	+Uplink channels 1-9 (RX1)
	598	+
	599	+869.525 - SF9BW125 (RX2 downlink only)
	600	+
	601	+
	602	+
	603	+=== 2.7.2 US902-928(US915) ===
	604	+
	605	+Used in USA, Canada and South America. Default use CHE=2
	606	+
	607	+(% style="color:#037691" %)**Uplink:**
	608	+
	609	+903.9 - SF7BW125 to SF10BW125
	610	+
	611	+904.1 - SF7BW125 to SF10BW125
	612	+
	613	+904.3 - SF7BW125 to SF10BW125
	614	+
	615	+904.5 - SF7BW125 to SF10BW125
	616	+
	617	+904.7 - SF7BW125 to SF10BW125
	618	+
	619	+904.9 - SF7BW125 to SF10BW125
	620	+
	621	+905.1 - SF7BW125 to SF10BW125
	622	+
	623	+905.3 - SF7BW125 to SF10BW125
	624	+
	625	+
	626	+(% style="color:#037691" %)**Downlink:**
	627	+
	628	+923.3 - SF7BW500 to SF12BW500
	629	+
	630	+923.9 - SF7BW500 to SF12BW500
	631	+
	632	+924.5 - SF7BW500 to SF12BW500
	633	+
	634	+925.1 - SF7BW500 to SF12BW500
	635	+
	636	+925.7 - SF7BW500 to SF12BW500
	637	+
	638	+926.3 - SF7BW500 to SF12BW500
	639	+
	640	+926.9 - SF7BW500 to SF12BW500
	641	+
	642	+927.5 - SF7BW500 to SF12BW500
	643	+
	644	+923.3 - SF12BW500(RX2 downlink only)
	645	+
	646	+
	647	+
	648	+=== 2.7.3 CN470-510 (CN470) ===
	649	+
	650	+Used in China, Default use CHE=1
	651	+
	652	+(% style="color:#037691" %)**Uplink:**
	653	+
	654	+486.3 - SF7BW125 to SF12BW125
	655	+
	656	+486.5 - SF7BW125 to SF12BW125
	657	+
	658	+486.7 - SF7BW125 to SF12BW125
	659	+
	660	+486.9 - SF7BW125 to SF12BW125
	661	+
	662	+487.1 - SF7BW125 to SF12BW125
	663	+
	664	+487.3 - SF7BW125 to SF12BW125
	665	+
	666	+487.5 - SF7BW125 to SF12BW125
	667	+
	668	+487.7 - SF7BW125 to SF12BW125
	669	+
	670	+
	671	+(% style="color:#037691" %)**Downlink:**
	672	+
	673	+506.7 - SF7BW125 to SF12BW125
	674	+
	675	+506.9 - SF7BW125 to SF12BW125
	676	+
	677	+507.1 - SF7BW125 to SF12BW125
	678	+
	679	+507.3 - SF7BW125 to SF12BW125
	680	+
	681	+507.5 - SF7BW125 to SF12BW125
	682	+
	683	+507.7 - SF7BW125 to SF12BW125
	684	+
	685	+507.9 - SF7BW125 to SF12BW125
	686	+
	687	+508.1 - SF7BW125 to SF12BW125
	688	+
	689	+505.3 - SF12BW125 (RX2 downlink only)
	690	+
	691	+
	692	+
	693	+=== 2.7.4 AU915-928(AU915) ===
	694	+
	695	+Default use CHE=2
	696	+
	697	+(% style="color:#037691" %)**Uplink:**
	698	+
	699	+916.8 - SF7BW125 to SF12BW125
	700	+
	701	+917.0 - SF7BW125 to SF12BW125
	702	+
	703	+917.2 - SF7BW125 to SF12BW125
	704	+
	705	+917.4 - SF7BW125 to SF12BW125
	706	+
	707	+917.6 - SF7BW125 to SF12BW125
	708	+
	709	+917.8 - SF7BW125 to SF12BW125
	710	+
	711	+918.0 - SF7BW125 to SF12BW125
	712	+
	713	+918.2 - SF7BW125 to SF12BW125
	714	+
	715	+
	716	+(% style="color:#037691" %)**Downlink:**
	717	+
	718	+923.3 - SF7BW500 to SF12BW500
	719	+
	720	+923.9 - SF7BW500 to SF12BW500
	721	+
	722	+924.5 - SF7BW500 to SF12BW500
	723	+
	724	+925.1 - SF7BW500 to SF12BW500
	725	+
	726	+925.7 - SF7BW500 to SF12BW500
	727	+
	728	+926.3 - SF7BW500 to SF12BW500
	729	+
	730	+926.9 - SF7BW500 to SF12BW500
	731	+
	732	+927.5 - SF7BW500 to SF12BW500
	733	+
	734	+923.3 - SF12BW500(RX2 downlink only)
	735	+
	736	+
	737	+
	738	+=== 2.7.5 AS920-923 & AS923-925 (AS923) ===
	739	+
	740	+(% style="color:#037691" %)**Default Uplink channel:**
	741	+
	742	+923.2 - SF7BW125 to SF10BW125
	743	+
	744	+923.4 - SF7BW125 to SF10BW125
	745	+
	746	+
	747	+(% style="color:#037691" %)**Additional Uplink Channel**:
	748	+
	749	+(OTAA mode, channel added by JoinAccept message)
	750	+
	751	+(% style="color:#037691" %)**AS920~~AS923 for Japan, Malaysia, Singapore**:
	752	+
	753	+922.2 - SF7BW125 to SF10BW125
	754	+
	755	+922.4 - SF7BW125 to SF10BW125
	756	+
	757	+922.6 - SF7BW125 to SF10BW125
	758	+
	759	+922.8 - SF7BW125 to SF10BW125
	760	+
	761	+923.0 - SF7BW125 to SF10BW125
	762	+
	763	+922.0 - SF7BW125 to SF10BW125
	764	+
	765	+
	766	+(% style="color:#037691" %)**AS923 ~~ AS925 for Brunei, Cambodia, Hong Kong, Indonesia, Laos, Taiwan, Thailand, Vietnam**:
	767	+
	768	+923.6 - SF7BW125 to SF10BW125
	769	+
	770	+923.8 - SF7BW125 to SF10BW125
	771	+
	772	+924.0 - SF7BW125 to SF10BW125
	773	+
	774	+924.2 - SF7BW125 to SF10BW125
	775	+
	776	+924.4 - SF7BW125 to SF10BW125
	777	+
	778	+924.6 - SF7BW125 to SF10BW125
	779	+
	780	+
	781	+(% style="color:#037691" %)** Downlink:**
	782	+
	783	+Uplink channels 1-8 (RX1)
	784	+
	785	+923.2 - SF10BW125 (RX2)
	786	+
	787	+
	788	+
	789	+=== 2.7.6 KR920-923 (KR920) ===
	790	+
	791	+Default channel:
	792	+
	793	+922.1 - SF7BW125 to SF12BW125
	794	+
	795	+922.3 - SF7BW125 to SF12BW125
	796	+
	797	+922.5 - SF7BW125 to SF12BW125
	798	+
	799	+
	800	+(% style="color:#037691" %)**Uplink: (OTAA mode, channel added by JoinAccept message)**
	801	+
	802	+922.1 - SF7BW125 to SF12BW125
	803	+
	804	+922.3 - SF7BW125 to SF12BW125
	805	+
	806	+922.5 - SF7BW125 to SF12BW125
	807	+
	808	+922.7 - SF7BW125 to SF12BW125
	809	+
	810	+922.9 - SF7BW125 to SF12BW125
	811	+
	812	+923.1 - SF7BW125 to SF12BW125
	813	+
	814	+923.3 - SF7BW125 to SF12BW125
	815	+
	816	+
	817	+(% style="color:#037691" %)**Downlink:**
	818	+
	819	+Uplink channels 1-7(RX1)
	820	+
	821	+921.9 - SF12BW125 (RX2 downlink only; SF12BW125 might be changed to SF9BW125)
	822	+
	823	+
	824	+
	825	+=== 2.7.7 IN865-867 (IN865) ===
	826	+
	827	+(% style="color:#037691" %)** Uplink:**
	828	+
	829	+865.0625 - SF7BW125 to SF12BW125
	830	+
	831	+865.4025 - SF7BW125 to SF12BW125
	832	+
	833	+865.9850 - SF7BW125 to SF12BW125
	834	+
	835	+
	836	+(% style="color:#037691" %) **Downlink:**
	837	+
	838	+Uplink channels 1-3 (RX1)
	839	+
	840	+866.550 - SF10BW125 (RX2)
	841	+
	842	+
	843	+
	844	+
	845	+== 2.8 LED Indicator ==
	846	+
	847	+The LSE01 has an internal LED which is to show the status of different state.
	848	+
	849	+* Blink once when device power on.
	850	+* Solid ON for 5 seconds once device successful Join the network.
	851	+* Blink once when device transmit a packet.
	852	+
	853	+== 2.9 Installation in Soil ==
	854	+
	855	+**Measurement the soil surface**
	856	+
	857	+
	858	+[[image:1654506634463-199.png]] ​
	859	+
668	668	(((
669		-[[image:image-20220708140453-6.png]]
	861	+(((
	862	+Choose the proper measuring position. Avoid the probe to touch rocks or hard things. Split the surface soil according to the measured deep. Keep the measured as original density. Vertical insert the probe into the soil to be measured. Make sure not shake when inserting.
670	670	)))
	864	+)))
671	671
672	672
673	673
674		-=== 2.9.2  Power consumption Analyze ===
	868	+[[image:1654506665940-119.png]]
675	675
676	676	(((
677		-Dragino battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
	871	+Dig a hole with diameter > 20CM.
678	678	)))
679	679
	874	+(((
	875	+Horizontal insert the probe to the soil and fill the hole for long term measurement.
	876	+)))
680	680
	878	+
	879	+== 2.10 ​Firmware Change Log ==
	880	+
681	681	(((
682		-Instruction to use as below:
	882	+**Firmware download link:**
683	683	)))
684	684
685	685	(((
686		-(% style="color:blue" %)**Step 1:  **(%%)Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/]]
	886	+[[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/]]
687	687	)))
688	688
	889	+(((
	890	+
	891	+)))
689	689
690	690	(((
691		-(% style="color:blue" %)**Step 2: **(%%) Open it and choose
	894	+**Firmware Upgrade Method: **[[Firmware Upgrade Instruction>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome]]
692	692	)))
693	693
694		-* (((
695		-Product Model
	897	+(((
	898	+
696	696	)))
697		-* (((
698		-Uplink Interval
	900	+
	901	+(((
	902	+**V1.0.**
699	699	)))
700		-* (((
701		-Working Mode
702		-)))
703	703
704	704	(((
705		-And the Life expectation in difference case will be shown on the right.
	906	+Release
706	706	)))
707	707
708		-[[image:image-20220708141352-7.jpeg]]
709	709
	910	+== 2.11 ​Battery Analysis ==
710	710
	912	+=== 2.11.1 ​Battery Type ===
711	711
712		-=== 2.9.3  ​Battery Note ===
	914	+(((
	915	+The LSE01 battery is a combination of a 4000mAh Li/SOCI2 Battery and a Super Capacitor. The battery is non-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
	916	+)))
713	713
714	714	(((
715		-The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
	919	+The battery is designed to last for more than 5 years for the LSN50.
716	716	)))
717	717
	922	+(((
	923	+(((
	924	+The battery-related documents are as below:
	925	+)))
	926	+)))
718	718
	928	+* (((
	929	+[[Battery Dimension>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/]],
	930	+)))
	931	+* (((
	932	+[[Lithium-Thionyl Chloride Battery  datasheet>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/]],
	933	+)))
	934	+* (((
	935	+[[Lithium-ion Battery-Capacitor datasheet>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/]], [[Tech Spec>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/]]
	936	+)))
719	719
720		-=== 2.9.4  Replace the battery ===
	938	+ [[image:image-20220610172436-1.png]]
721	721
	940	+
	941	+
	942	+=== 2.11.2 ​Battery Note ===
	943	+
722	722	(((
723		-The default battery pack of NSE01 includes a ER26500 plus super capacitor. If user can't find this pack locally, they can find ER26500 or equivalence without the SPC1520 capacitor, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes).
	945	+The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
724	724	)))
725	725
726	726
727	727
728		-= 3. ​ Access NB-IoT Module =
	950	+=== 2.11.3 Replace the battery ===
729	729
730	730	(((
731		-Users can directly access the AT command set of the NB-IoT module.
	953	+If Battery is lower than 2.7v, user should replace the battery of LSE01.
732	732	)))
733	733
734	734	(((
735		-The AT Command set can refer the BC35-G NB-IoT Module AT Command: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/]]
	957	+You can change the battery in the LSE01.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
736	736	)))
737	737
738		-[[image:1657261278785-153.png]]
	960	+(((
	961	+The default battery pack of LSE01 includes a ER18505 plus super capacitor. If user can’t find this pack locally, they can find ER18505 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
	962	+)))
739	739
740	740
741	741
742		-= 4.  Using the AT Commands =
	966	+= 3. ​Using the AT Commands =
743	743
744		-== 4.1  Access AT Commands ==
	968	+== 3.1 Access AT Commands ==
745	745
746		-See this link for detail: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/]]
747	747
	971	+LSE01 supports AT Command set in the stock firmware. You can use a USB to TTL adapter to connect to LSE01 for using AT command, as below.
748	748
749		-AT+<CMD>?  : Help on <CMD>
	973	+[[image:1654501986557-872.png||height="391" width="800"]]
750	750
751		-AT+<CMD>         : Run <CMD>
752	752
753		-AT+<CMD>=<value> : Set the value
	976	+Or if you have below board, use below connection:
754	754
755		-AT+<CMD>=?  : Get the value
756	756
	979	+[[image:1654502005655-729.png||height="503" width="801"]]
757	757
	981	+
	982	+
	983	+In the PC, you need to set the serial baud rate to (% style="color:green" %)**9600**(%%) to access the serial console for LSE01. LSE01 will output system info once power on as below:
	984	+
	985	+
	986	+ [[image:1654502050864-459.png||height="564" width="806"]]
	987	+
	988	+
	989	+Below are the available commands, a more detailed AT Command manual can be found at [[AT Command Manual>>https://www.dropbox.com/sh/qr6vproz4z4kzjz/AAAD48h3OyWrU1hq_Cqm8jIwa?dl=0]]: [[https:~~/~~/www.dropbox.com/sh/qr6vproz4z4kzjz/AAAD48h3OyWrU1hq_Cqm8jIwa?dl=0>>https://www.dropbox.com/sh/qr6vproz4z4kzjz/AAAD48h3OyWrU1hq_Cqm8jIwa?dl=0]]
	990	+
	991	+
	992	+(% style="background-color:#dcdcdc" %)**AT+<CMD>=?AT+<CMD>? **(%%) : Help on <CMD>
	993	+
	994	+(% style="background-color:#dcdcdc" %)**AT+<CMD>=?AT+<CMD> **(%%) : Run <CMD>
	995	+
	996	+(% style="background-color:#dcdcdc" %)**AT+<CMD>=?AT+<CMD>=<value>**(%%) : Set the value
	997	+
	998	+(% style="background-color:#dcdcdc" %)**AT+<CMD>=?AT+<CMD>=?**(%%)  : Get the value
	999	+
	1000	+
758	758	(% style="color:#037691" %)**General Commands**(%%)
759	759
760		-AT  : Attention
	1003	+(% style="background-color:#dcdcdc" %)**AT**(%%)  : Attention
761	761
762		-AT?  : Short Help
	1005	+(% style="background-color:#dcdcdc" %)**AT?**(%%)  : Short Help
763	763
764		-ATZ  : MCU Reset
	1007	+(% style="background-color:#dcdcdc" %)**ATZ**(%%)  : MCU Reset
765	765
766		-AT+TDC  : Application Data Transmission Interval
	1009	+(% style="background-color:#dcdcdc" %)**AT+TDC**(%%)  : Application Data Transmission Interval
767	767
768		-AT+CFG  : Print all configurations
769	769
770		-AT+CFGMOD           : Working mode selection
	1012	+(% style="color:#037691" %)**Keys, IDs and EUIs management**
771	771
772		-AT+INTMOD            : Set the trigger interrupt mode
	1014	+(% style="background-color:#dcdcdc" %)**AT+APPEUI**(%%)              : Application EUI
773	773
774		-AT+5VT  : Set extend the time of 5V power
	1016	+(% style="background-color:#dcdcdc" %)**AT+APPKEY**(%%)              : Application Key
775	775
776		-AT+PRO  : Choose agreement
	1018	+(% style="background-color:#dcdcdc" %)**AT+APPSKEY**(%%)            : Application Session Key
777	777
778		-AT+WEIGRE  : Get weight or set weight to 0
	1020	+(% style="background-color:#dcdcdc" %)**AT+DADDR**(%%)              : Device Address
779	779
780		-AT+WEIGAP  : Get or Set the GapValue of weight
	1022	+(% style="background-color:#dcdcdc" %)**AT+DEUI**(%%)                   : Device EUI
781	781
782		-AT+RXDL  : Extend the sending and receiving time
	1024	+(% style="background-color:#dcdcdc" %)**AT+NWKID**(%%)               : Network ID (You can enter this command change only after successful network connection)
783	783
784		-AT+CNTFAC  : Get or set counting parameters
	1026	+(% style="background-color:#dcdcdc" %)**AT+NWKSKEY**(%%)          : Network Session Key Joining and sending date on LoRa network
785	785
786		-AT+SERVADDR  : Server Address
	1028	+(% style="background-color:#dcdcdc" %)**AT+CFM**(%%)  : Confirm Mode
787	787
	1030	+(% style="background-color:#dcdcdc" %)**AT+CFS**(%%)                     : Confirm Status
788	788
789		-(% style="color:#037691" %)**COAP Management**
	1032	+(% style="background-color:#dcdcdc" %)**AT+JOIN**(%%)  : Join LoRa? Network
790	790
791		-AT+URI            : Resource parameters
	1034	+(% style="background-color:#dcdcdc" %)**AT+NJM**(%%)  : LoRa? Network Join Mode
792	792
	1036	+(% style="background-color:#dcdcdc" %)**AT+NJS**(%%)                     : LoRa? Network Join Status
793	793
794		-(% style="color:#037691" %)**UDP Management**
	1038	+(% style="background-color:#dcdcdc" %)**AT+RECV**(%%)                  : Print Last Received Data in Raw Format
795	795
796		-AT+CFM          : Upload confirmation mode (only valid for UDP)
	1040	+(% style="background-color:#dcdcdc" %)**AT+RECVB**(%%)                : Print Last Received Data in Binary Format
797	797
	1042	+(% style="background-color:#dcdcdc" %)**AT+SEND**(%%)                  : Send Text Data
798	798
799		-(% style="color:#037691" %)**MQTT Management**
	1044	+(% style="background-color:#dcdcdc" %)**AT+SENB**(%%)                  : Send Hexadecimal Data
800	800
801		-AT+CLIENT               : Get or Set MQTT client
802	802
803		-AT+UNAME  : Get or Set MQTT Username
	1047	+(% style="color:#037691" %)**LoRa Network Management**
804	804
805		-AT+PWD                  : Get or Set MQTT password
	1049	+(% style="background-color:#dcdcdc" %)**AT+ADR**(%%)          : Adaptive Rate
806	806
807		-AT+PUBTOPIC  : Get or Set MQTT publish topic
	1051	+(% style="background-color:#dcdcdc" %)**AT+CLASS**(%%)  : LoRa Class(Currently only support class A
808	808
809		-AT+SUBTOPIC  : Get or Set MQTT subscription topic
	1053	+(% style="background-color:#dcdcdc" %)**AT+DCS**(%%)  : Duty Cycle Setting
810	810
	1055	+(% style="background-color:#dcdcdc" %)**AT+DR**(%%)  : Data Rate (Can Only be Modified after ADR=0)
811	811
812		-(% style="color:#037691" %)**Information**
	1057	+(% style="background-color:#dcdcdc" %)**AT+FCD**(%%)  : Frame Counter Downlink
813	813
814		-AT+FDR  : Factory Data Reset
	1059	+(% style="background-color:#dcdcdc" %)**AT+FCU**(%%)  : Frame Counter Uplink
815	815
816		-AT+PWORD  : Serial Access Password
	1061	+(% style="background-color:#dcdcdc" %)**AT+JN1DL**(%%)  : Join Accept Delay1
817	817
	1063	+(% style="background-color:#dcdcdc" %)**AT+JN2DL**(%%)  : Join Accept Delay2
818	818
	1065	+(% style="background-color:#dcdcdc" %)**AT+PNM**(%%)  : Public Network Mode
819	819
820		-= ​5.  FAQ =
	1067	+(% style="background-color:#dcdcdc" %)**AT+RX1DL**(%%)  : Receive Delay1
821	821
822		-== 5.1 ​ How to Upgrade Firmware ==
	1069	+(% style="background-color:#dcdcdc" %)**AT+RX2DL**(%%)  : Receive Delay2
823	823
	1071	+(% style="background-color:#dcdcdc" %)**AT+RX2DR**(%%)  : Rx2 Window Data Rate
824	824
	1073	+(% style="background-color:#dcdcdc" %)**AT+RX2FQ**(%%)  : Rx2 Window Frequency
	1074	+
	1075	+(% style="background-color:#dcdcdc" %)**AT+TXP**(%%)  : Transmit Power
	1076	+
	1077	+(% style="background-color:#dcdcdc" %)**AT+ MOD**(%%)  : Set work mode
	1078	+
	1079	+
	1080	+(% style="color:#037691" %)**Information**
	1081	+
	1082	+(% style="background-color:#dcdcdc" %)**AT+RSSI**(%%)           : RSSI of the Last Received Packet
	1083	+
	1084	+(% style="background-color:#dcdcdc" %)**AT+SNR**(%%)           : SNR of the Last Received Packet
	1085	+
	1086	+(% style="background-color:#dcdcdc" %)**AT+VER**(%%)           : Image Version and Frequency Band
	1087	+
	1088	+(% style="background-color:#dcdcdc" %)**AT+FDR**(%%)           : Factory Data Reset
	1089	+
	1090	+(% style="background-color:#dcdcdc" %)**AT+PORT**(%%)  : Application Port
	1091	+
	1092	+(% style="background-color:#dcdcdc" %)**AT+CHS**(%%)  : Get or Set Frequency (Unit: Hz) for Single Channel Mode
	1093	+
	1094	+ (% style="background-color:#dcdcdc" %)**AT+CHE**(%%)  : Get or Set eight channels mode, Only for US915, AU915, CN470
	1095	+
	1096	+
	1097	+= ​4. FAQ =
	1098	+
	1099	+== 4.1 ​How to change the LoRa Frequency Bands/Region? ==
	1100	+
825	825	(((
826		-User can upgrade the firmware for 1) bug fix, 2) new feature release.
	1102	+You can follow the instructions for [[how to upgrade image>>||anchor="H2.10200BFirmwareChangeLog"]].
	1103	+When downloading the images, choose the required image file for download. ​
827	827	)))
828	828
829	829	(((
830		-Please see this link for how to upgrade:  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList>>http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList]]
	1107	+
831	831	)))
832	832
833	833	(((
834		-(% style="color:red" %)Notice, NSE01 and LSE01 share the same mother board. They use the same connection and method to update.
	1111	+How to set up LSE01 to work in 8 channel mode By default, the frequency bands US915, AU915, CN470 work in 72 frequencies. Many gateways are 8 channel gateways, and in this case, the OTAA join time and uplink schedule is long and unpredictable while the end node is hopping in 72 frequencies.
835	835	)))
836	836
	1114	+(((
	1115	+
	1116	+)))
837	837
	1118	+(((
	1119	+You can configure the end node to work in 8 channel mode by using the AT+CHE command. The 500kHz channels are always included for OTAA.
	1120	+)))
838	838
839		-= 6.  Trouble Shooting =
	1122	+(((
	1123	+
	1124	+)))
840	840
841		-== 6.1  ​Connection problem when uploading firmware ==
	1126	+(((
	1127	+For example, in **US915** band, the frequency table is as below. By default, the end node will use all channels (0~~71) for OTAA Join process. After the OTAA Join, the end node will use these all channels (0~~71) to send uplink packets.
	1128	+)))
842	842
	1130	+[[image:image-20220606154726-3.png]]
843	843
844		-(% class="wikigeneratedid" %)
	1132	+
	1133	+When you use the TTN network, the US915 frequency bands use are:
	1134	+
	1135	+* 903.9 - SF7BW125 to SF10BW125
	1136	+* 904.1 - SF7BW125 to SF10BW125
	1137	+* 904.3 - SF7BW125 to SF10BW125
	1138	+* 904.5 - SF7BW125 to SF10BW125
	1139	+* 904.7 - SF7BW125 to SF10BW125
	1140	+* 904.9 - SF7BW125 to SF10BW125
	1141	+* 905.1 - SF7BW125 to SF10BW125
	1142	+* 905.3 - SF7BW125 to SF10BW125
	1143	+* 904.6 - SF8BW500
	1144	+
845	845	(((
846		-(% style="font-size:14px" %)**Please see: **(%%)[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting>>http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting||style="background-color: rgb(255, 255, 255); font-size: 14px;"]]
	1146	+Because the end node is now hopping in 72 frequency, it makes it difficult for the devices to Join the TTN network and uplink data. To solve this issue, you can access the device via the AT commands and run:
	1147	+
	1148	+* (% style="color:#037691" %)**AT+CHE=2**
	1149	+* (% style="color:#037691" %)**ATZ**
847	847	)))
848	848
	1152	+(((
	1153	+
849	849
	1155	+to set the end node to work in 8 channel mode. The device will work in Channel 8-15 & 64-71 for OTAA, and channel 8-15 for Uplink.
	1156	+)))
850	850
851		-== 6.2  AT Command input doesn't work ==
	1158	+(((
	1159	+
	1160	+)))
852	852
853	853	(((
	1163	+The **AU915** band is similar. Below are the AU915 Uplink Channels.
	1164	+)))
	1165	+
	1166	+[[image:image-20220606154825-4.png]]
	1167	+
	1168	+
	1169	+== 4.2 ​Can I calibrate LSE01 to different soil types? ==
	1170	+
	1171	+LSE01 is calibrated for saline-alkali soil and loamy soil. If users want to use it for other soil, they can calibrate the value in the IoT platform base on the value measured by saline-alkali soil and loamy soil. The formula can be found at [[this link>>https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/&file=Calibrate_to_other_Soil_20220605.pdf]].
	1172	+
	1173	+
	1174	+= 5. Trouble Shooting =
	1175	+
	1176	+== 5.1 ​Why I can't join TTN in US915 / AU915 bands? ==
	1177	+
	1178	+It is due to channel mapping. Please see the [[Eight Channel Mode>>doc:Main.End Device AT Commands and Downlink Command.WebHome||anchor="H7.19EightChannelMode"]] section above for details.
	1179	+
	1180	+
	1181	+== 5.2 AT Command input doesn't work ==
	1182	+
	1183	+(((
854	854	In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
855	855	)))
856	856
857	857
	1188	+== 5.3 Device rejoin in at the second uplink packet ==
858	858
859		-= 7. ​ Order Info =
	1190	+(% style="color:#4f81bd" %)**Issue describe as below:**
860	860
	1192	+[[image:1654500909990-784.png]]
861	861
862		-Part Number**:** (% style="color:#4f81bd" %)**NSE01**
863	863
	1195	+(% style="color:#4f81bd" %)**Cause for this issue:**
864	864
	1197	+(((
	1198	+The fuse on LSE01 is not large enough, some of the soil probe require large current up to 5v 800mA, in a short pulse. When this happen, it cause the device reboot so user see rejoin.
	1199	+)))
	1200	+
	1201	+
	1202	+(% style="color:#4f81bd" %)**Solution: **
	1203	+
	1204	+All new shipped LSE01 after 2020-May-30 will have this to fix. For the customer who see this issue, please bypass the fuse as below:
	1205	+
	1206	+[[image:1654500929571-736.png||height="458" width="832"]]
	1207	+
	1208	+
	1209	+= 6. ​Order Info =
	1210	+
	1211	+
	1212	+Part Number**:** (% style="color:#4f81bd" %)**LSE01-XX-YY**
	1213	+
	1214	+
	1215	+(% style="color:#4f81bd" %)**XX**(%%)**:** The default frequency band
	1216	+
	1217	+* (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band
	1218	+* (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band
	1219	+* (% style="color:red" %)**EU433**(%%): LoRaWAN EU433 band
	1220	+* (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band
	1221	+* (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band
	1222	+* (% style="color:red" %)**US915**(%%): LoRaWAN US915 band
	1223	+* (% style="color:red" %)**IN865**(%%):  LoRaWAN IN865 band
	1224	+* (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
	1225	+
	1226	+(% style="color:#4f81bd" %)**YY**(%%)**: **Battery Option
	1227	+
	1228	+* (% style="color:red" %)**4**(%%): 4000mAh battery
	1229	+* (% style="color:red" %)**8**(%%): 8500mAh battery
	1230	+
865	865	(% class="wikigeneratedid" %)
866	866	(((
867	867
868	868	)))
869	869
870		-= 8.  Packing Info =
	1236	+= 7. Packing Info =
871	871
872	872	(((
873	873
874	874
875	875	(% style="color:#037691" %)**Package Includes**:
	1242	+)))
876	876
877		-
878		-* NSE01 NB-IoT Soil Moisture & EC Sensor x 1
879		-* External antenna x 1
	1244	+* (((
	1245	+LSE01 LoRaWAN Soil Moisture & EC Sensor x 1
880	880	)))
881	881
882	882	(((
...	...	@@ -883,20 +883,24 @@
883	883
884	884
885	885	(% style="color:#037691" %)**Dimension and weight**:
	1252	+)))
886	886
887		-
888		-* Size: 195 x 125 x 55 mm
889		-* Weight:   420g
	1254	+* (((
	1255	+Device Size: cm
890	890	)))
	1257	+* (((
	1258	+Device Weight: g
	1259	+)))
	1260	+* (((
	1261	+Package Size / pcs : cm
	1262	+)))
	1263	+* (((
	1264	+Weight / pcs : g
891	891
892		-(((
893	893
894		-
895		-
896		-
897	897	)))
898	898
899		-= 9.  Support =
	1269	+= 8. Support =
900	900
901	901	* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
902	902	* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]

1657259653666-883.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-344.4 KB

Content

1657260785982-288.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-138.2 KB

Content

1657261119050-993.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-126.1 KB

Content

1657261278785-153.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-126.1 KB

Content

image-20220708133731-5.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-8.7 KB

Content

image-20220708140453-6.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-132.7 KB

Content

image-20220708141352-7.jpeg

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-102.7 KB

Content