Last modified by Bei Jinggeng on 2024/05/31 09:53
<
From version < 45.5 >
edited by Xiaoling
on 2022/07/08 10:39
To version < 45.7 >
edited by Xiaoling
on 2022/07/08 11:03
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -164,24 +164,24 @@
164 164  
165 165  Connection:
166 166  
167 -USB TTL GND <~-~-~-~-> GND
167 + (% style="background-color:yellow" %)USB TTL GND <~-~-~-~-> GND
168 168  
169 -USB TTL TXD <~-~-~-~-> UART_RXD
169 + (% style="background-color:yellow" %)USB TTL TXD <~-~-~-~-> UART_RXD
170 170  
171 -USB TTL RXD <~-~-~-~-> UART_TXD
171 + (% style="background-color:yellow" %)USB TTL RXD <~-~-~-~-> UART_TXD
172 172  
173 173  
174 174  
175 175  In the PC, use below serial tool settings:
176 176  
177 -* Baud: **9600**
178 -* Data bits:** 8**
179 -* Stop bits: **1**
180 -* Parity: **None**
181 -* Flow Control: **None**
177 +* Baud: ** (% style="background-color:green" %)9600**(%%)
178 +* Data bits:** (% style="background-color:green" %)8**(%%)
179 +* Stop bits: **(% style="background-color:green" %)1**(%%)
180 +* Parity: **(% style="background-color:green" %)None**(%%)
181 +* Flow Control: **(% style="background-color:green" %)None**
182 182  
183 183  
184 -Make sure the switch is in FLASH position, then power on device by connecting the jumper on NSE01. NSE01 will output system info once power on as below, we can enter the **password: 12345678** to access AT Command input.
184 +Make sure the switch is in FLASH position, then power on device by connecting the jumper on NSE01. NSE01 will output system info once power on as below, we can enter the **(% style="background-color:green" %)password: 12345678**(%%) to access AT Command input.
185 185  
186 186  [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image009.jpg]]
187 187  
... ... @@ -190,21 +190,20 @@
190 190  [[http:~~/~~/www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/]]
191 191  
192 192  
193 -1.
194 -11.
195 -111. Use CoAP protocol to uplink data 
196 196  
194 +=== 2.2.4 Use CoAP protocol to uplink data === 
197 197  
198 -Note: if you don’t have CoAP server, you can refer this link to set up one:
199 199  
197 +(% style="background-color:red" %)Note: if you don’t have CoAP server, you can refer this link to set up one:
198 +
200 200  [[http:~~/~~/wiki.dragino.com/index.php?title=Set_up_CoAP_Server>>url:http://wiki.dragino.com/index.php?title=Set_up_CoAP_Server]]
201 201  
202 202  
203 203  Use below commands:
204 204  
205 -* **AT+PRO=1**    ~/~/ Set to use CoAP protocol to uplink
206 -* **AT+SERVADDR=120.24.4.116,5683   **~/~/ to set CoAP server address and port
207 -* **AT+URI=5,11,"mqtt",11,"coap",12,"0",15,"c=text1",23,"0"       **~/~/Set COAP resource path
204 +* **(% style="color:blue" %)AT+PRO=1**  (%%)  ~/~/ Set to use CoAP protocol to uplink
205 +* **(% style="color:blue" %)AT+SERVADDR=120.24.4.116,5683   ** (%%)~/~/ to set CoAP server address and port
206 +* **(% style="color:blue" %)AT+URI=5,11,"mqtt",11,"coap",12,"0",15,"c=text1",23,"0" ** (%%)      ~/~/Set COAP resource path
208 208  
209 209  
210 210  For parameter description, please refer to AT command set
... ... @@ -212,21 +212,20 @@
212 212  [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image011.jpg]]
213 213  
214 214  
215 -After configure the server address and **reset the device** (via AT+ATZ ), NSE01 will start to uplink sensor values to CoAP server.
214 +After configure the server address and **(% style="color:green" %)reset the device**(%%) (via AT+ATZ ), NSE01 will start to uplink sensor values to CoAP server.
216 216  
217 217  [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image013.jpg]]
218 218  
219 -1.
220 -11.
221 -111. Use UDP protocol to uplink data(Default protocol)
222 222  
219 +=== 2.2.5 Use UDP protocol to uplink data(Default protocol) ===
223 223  
221 +
224 224  This feature is supported since firmware version v1.0.1
225 225  
226 226  
227 -* **AT+PRO=2   ** ~/~/ Set to use UDP protocol to uplink
228 -* **AT+SERVADDR=120.24.4.116,5601   **~/~/ to set UDP server address and port
229 -* **AT+CFM=1       **~/~/If the server does not respond, this command is unnecessary
225 +* **(% style="color:blue" %)AT+PRO=2   ** (%%) ~/~/ Set to use UDP protocol to uplink
226 +* **(% style="color:blue" %)AT+SERVADDR=120.24.4.116,5601   ** (%%) ~/~/ to set UDP server address and port
227 +* **(% style="color:blue" %)AT+CFM=1       ** (%%) ~/~/If the server does not respond, this command is unnecessary
230 230  
231 231  [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image015.jpg]]
232 232  
... ... @@ -237,21 +237,19 @@
237 237  [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image017.jpg]]
238 238  
239 239  
240 -1.
241 -11.
242 -111. Use MQTT protocol to uplink data
238 +=== 2.2.6 Use MQTT protocol to uplink data ===
243 243  
244 244  
245 245  This feature is supported since firmware version v110
246 246  
247 247  
248 -* **AT+PRO=3   ** ~/~/Set to use MQTT protocol to uplink
249 -* **AT+SERVADDR=120.24.4.116,1883   **~/~/Set MQTT server address and port
250 -* **AT+CLIENT=CLIENT **~/~/Set up the CLIENT of MQTT
251 -* **AT+UNAME=UNAME                           **~/~/Set the username of MQTT
252 -* **AT+PWD=PWD                                      **~/~/Set the password of MQTT
253 -* **AT+PUBTOPIC=NSE01_PUB   **~/~/Set the sending topic of MQTT
254 -* **AT+SUBTOPIC=NSE01_SUB    **~/~/Set the subscription topic of MQTT
244 +* **(% style="color:blue" %)AT+PRO=3   ** (%%) ~/~/Set to use MQTT protocol to uplink
245 +* **(% style="color:blue" %)AT+SERVADDR=120.24.4.116,1883   ** (%%) ~/~/Set MQTT server address and port
246 +* **(% style="color:blue" %)AT+CLIENT=CLIENT ** (%%)~/~/Set up the CLIENT of MQTT
247 +* **(% style="color:blue" %)AT+UNAME=UNAME            **(%%)~/~/Set the username of MQTT
248 +* **(% style="color:blue" %)AT+PWD=PWD                  **(%%)~/~/Set the password of MQTT
249 +* **(% style="color:blue" %)AT+PUBTOPIC=NSE01_PUB   **(%%)~/~/Set the sending topic of MQTT
250 +* **(% style="color:blue" %)AT+SUBTOPIC=NSE01_SUB    **(%%) ~/~/Set the subscription topic of MQTT
255 255  
256 256  
257 257  [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image019.gif]]
... ... @@ -262,16 +262,14 @@
262 262  MQTT protocol has a much higher power consumption compare vs UDP / CoAP protocol. Please check the power analyze document and adjust the uplink period to a suitable interval.
263 263  
264 264  
265 -1.
266 -11.
267 -111. Use TCP protocol to uplink data
261 +=== 2.2.7 Use TCP protocol to uplink data ===
268 268  
269 269  
270 270  This feature is supported since firmware version v110
271 271  
272 272  
273 -* **AT+PRO=4   ** ~/~/ Set to use TCP protocol to uplink
274 -* **AT+SERVADDR=120.24.4.116,5600   **~/~/ to set TCP server address and port
267 +* **(% style="color:blue" %)AT+PRO=4   ** (%%) ~/~/ Set to use TCP protocol to uplink
268 +* **(% style="color:blue" %)AT+SERVADDR=120.24.4.116,5600   **(%%) ~/~/ to set TCP server address and port
275 275  
276 276  [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image023.jpg]]
277 277  
... ... @@ -280,18 +280,16 @@
280 280  [[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image025.jpg]]
281 281  
282 282  
283 -1.
284 -11.
285 -111. Change Update Interval
277 +=== 2.2.8 Change Update Interval ===
286 286  
287 -User can use below command to change the **uplink interval**.
279 +User can use below command to change the **(% style="color:green" %)uplink interval**.
288 288  
289 -**~ AT+TDC=600      **~/~/ Set Update Interval to 600s
281 +**~ (% style="color:blue" %)AT+TDC=600      ** (%%)~/~/ Set Update Interval to 600s
290 290  
291 291  
292 -**NOTE:**
284 +**(% style="color:red" %)NOTE:**
293 293  
294 -1. By default, the device will send an uplink message every 1 hour.
286 +(% style="color:red" %)1. By default, the device will send an uplink message every 1 hour.
295 295  
296 296  
297 297  

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0