Last modified by Bei Jinggeng on 2024/05/31 09:53
<
From version < 35.25 >
edited by Xiaoling
on 2022/06/25 16:23
To version < 45.6 >
edited by Xiaoling
on 2022/07/08 10:57
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -LSE01-LoRaWAN Soil Moisture & EC Sensor User Manual
1 +NSE01 - NB-IoT Soil Moisture & EC Sensor User Manual
Content
... ... @@ -13,75 +13,82 @@
13 13  
14 14  **Table of Contents:**
15 15  
16 -{{toc/}}
17 17  
18 18  
19 19  
20 20  
21 21  
21 += 1.  Introduction =
22 22  
23 -= 1. Introduction =
23 +== 1.1 ​ What is LoRaWAN Soil Moisture & EC Sensor ==
24 24  
25 -== 1.1 ​What is LoRaWAN Soil Moisture & EC Sensor ==
26 -
27 27  (((
28 28  
29 29  
30 -The Dragino LSE01 is a (% style="color:#4f81bd" %)**LoRaWAN Soil Moisture & EC Sensor**(%%) for IoT of Agriculture. It is designed to measure the soil moisture of saline-alkali soil and loamy soil. The soil sensor uses FDR method to calculate the soil moisture with the compensation from soil temperature and conductivity. It also has been calibrated in factory for Mineral soil type.
31 -)))
28 +Dragino NSE01 is an (% style="color:blue" %)**NB-IOT soil moisture & EC sensor**(%%) for agricultural IoT. Used to measure the soil moisture of saline-alkali soil and loam. The soil sensor uses the FDR method to calculate soil moisture and compensates it with soil temperature and electrical conductivity. It has also been calibrated for mineral soil types at the factory.
32 32  
33 -(((
34 -It detects (% style="color:#4f81bd" %)**Soil Moisture**(%%), (% style="color:#4f81bd" %)**Soil Temperature**(%%) and (% style="color:#4f81bd" %)**Soil Conductivity**(%%), and uploads the value via wireless to LoRaWAN IoT Server.
35 -)))
30 +It can detect (% style="color:blue" %)**Soil Moisture, Soil Temperature and Soil Conductivity**(%%), and upload its value to the server wirelessly.
36 36  
37 -(((
38 -The LoRa wireless technology used in LES01 allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
39 -)))
32 +The wireless technology used in NSE01 allows the device to send data at a low data rate and reach ultra-long distances, providing ultra-long-distance spread spectrum Communication.
40 40  
41 -(((
42 -LES01 is powered by (% style="color:#4f81bd" %)**4000mA or 8500mAh Li-SOCI2 battery**(%%), It is designed for long term use up to 10 years.
43 -)))
34 +NSE01 are powered by (% style="color:blue" %)**8500mAh Li-SOCI2**(%%) batteries, which can be used for up to 5 years.  
44 44  
45 -(((
46 -Each LES01 is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
36 +
47 47  )))
48 48  
49 -
50 50  [[image:1654503236291-817.png]]
51 51  
52 52  
53 -[[image:1654503265560-120.png]]
42 +[[image:1657245163077-232.png]]
54 54  
55 55  
56 56  
57 57  == 1.2 ​Features ==
58 58  
59 -* LoRaWAN 1.0.3 Class A
60 -* Ultra low power consumption
48 +
49 +* NB-IoT Bands: B1/B3/B8/B5/B20/B28 @H-FDD
61 61  * Monitor Soil Moisture
62 62  * Monitor Soil Temperature
63 63  * Monitor Soil Conductivity
64 -* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
65 65  * AT Commands to change parameters
66 66  * Uplink on periodically
67 67  * Downlink to change configure
68 68  * IP66 Waterproof Enclosure
69 -* 4000mAh or 8500mAh Battery for long term use
57 +* Ultra-Low Power consumption
58 +* AT Commands to change parameters
59 +* Micro SIM card slot for NB-IoT SIM
60 +* 8500mAh Battery for long term use
70 70  
71 71  
72 72  
64 +== 1.3  Specification ==
73 73  
74 74  
67 +(% style="color:#037691" %)**Common DC Characteristics:**
75 75  
76 -== 1.3 Specification ==
69 +* Supply Voltage: 2.1v ~~ 3.6v
70 +* Operating Temperature: -40 ~~ 85°C
77 77  
72 +
73 +(% style="color:#037691" %)**NB-IoT Spec:**
74 +
75 +* - B1 @H-FDD: 2100MHz
76 +* - B3 @H-FDD: 1800MHz
77 +* - B8 @H-FDD: 900MHz
78 +* - B5 @H-FDD: 850MHz
79 +* - B20 @H-FDD: 800MHz
80 +* - B28 @H-FDD: 700MHz
81 +
82 +
83 +(% style="color:#037691" %)**Probe Specification:**
84 +
78 78  Measure Volume: Base on the centra pin of the probe, a cylinder with 7cm diameter and 10cm height.
79 79  
80 -[[image:image-20220606162220-5.png]]
87 +[[image:image-20220708101224-1.png]]
81 81  
82 82  
83 83  
84 -== ​1.4 Applications ==
91 +== ​1.4  Applications ==
85 85  
86 86  * Smart Agriculture
87 87  
... ... @@ -88,73 +88,208 @@
88 88  (% class="wikigeneratedid" id="H200B1.5FirmwareChangelog" %)
89 89  ​
90 90  
91 -== 1.5 Firmware Change log ==
98 +== 1.5  Pin Definitions ==
92 92  
93 93  
94 -**LSE01 v1.0 :**  Release
101 +[[image:1657246476176-652.png]]
95 95  
96 96  
97 97  
98 -= 2. Configure LSE01 to connect to LoRaWAN network =
105 += 2.  Use NSE01 to communicate with IoT Server =
99 99  
100 -== 2.1 How it works ==
107 +== 2.1  How it works ==
101 101  
109 +
102 102  (((
103 -The LSE01 is configured as LoRaWAN OTAA Class A mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and power on the LSE0150. It will automatically join the network via OTAA and start to send the sensor value
111 +The NSE01 is equipped with a NB-IoT module, the pre-loaded firmware in NSE01 will get environment data from sensors and send the value to local NB-IoT network via the NB-IoT module.  The NB-IoT network will forward this value to IoT server via the protocol defined by NSE01.
104 104  )))
105 105  
114 +
106 106  (((
107 -In case you can’t set the OTAA keys in the LoRaWAN OTAA server, and you have to use the keys from the server, you can [[use AT Commands >>||anchor="H3.200BUsingtheATCommands"]].
116 +The diagram below shows the working flow in default firmware of NSE01:
108 108  )))
109 109  
119 +[[image:image-20220708101605-2.png]]
110 110  
121 +(((
122 +
123 +)))
111 111  
112 -== 2.2 ​Quick guide to connect to LoRaWAN server (OTAA) ==
113 113  
114 -Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LG308>>url:http://www.dragino.com/products/lora/item/140-lg308.html]] as a LoRaWAN gateway in this example.
115 115  
127 +== 2.2 ​ Configure the NSE01 ==
116 116  
117 -[[image:1654503992078-669.png]]
129 +=== 2.2.1 Test Requirement ===
118 118  
119 119  
120 -The LG308 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
132 +To use NSE01 in your city, make sure meet below requirements:
121 121  
134 +* Your local operator has already distributed a NB-IoT Network there.
135 +* The local NB-IoT network used the band that NSE01 supports.
136 +* Your operator is able to distribute the data received in their NB-IoT network to your IoT server.
122 122  
123 -(% style="color:blue" %)**Step 1**(%%):  Create a device in TTN with the OTAA keys from LSE01.
124 124  
125 -Each LSE01 is shipped with a sticker with the default device EUI as below:
139 +Below figure shows our testing structure. Here we have NB-IoT network coverage by China Mobile, the band they use is B8.  The NSE01 will use CoAP((% style="color:red" %)120.24.4.116:5683)(%%) or raw UDP((% style="color:red" %)120.24.4.116:5601)(%%) or MQTT((% style="color:red" %)120.24.4.116:1883)(%%)or TCP((% style="color:red" %)120.24.4.116:5600)(%%)protocol to send data to the test server
126 126  
127 -[[image:image-20220606163732-6.jpeg]]
128 128  
129 -You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
142 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image002.gif]]
130 130  
131 -**Add APP EUI in the application**
132 132  
133 133  
134 -[[image:1654504596150-405.png]]
146 +=== 2.2.2 Insert SIM card ===
135 135  
148 +Insert the NB-IoT Card get from your provider.
136 136  
137 137  
138 -**Add APP KEY and DEV EUI**
151 +User need to take out the NB-IoT module and insert the SIM card like below:
139 139  
140 -[[image:1654504683289-357.png]]
141 141  
154 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image004.gif]]
142 142  
143 143  
144 -(% style="color:blue" %)**Step 2**(%%): Power on LSE01
157 +=== 2.2.3 Connect USB – TTL to NSE01 to configure it ===
145 145  
146 146  
147 -Put a Jumper on JP2 to power on the device. ( The Jumper must be in FLASH position).
160 +User need to configure NSE01 via serial port to set the **(% style="color:blue" %)Server Address** / **Uplink Topic** (%%)to define where and how-to uplink packets. NSE01 support AT Commands, user can use a USB to TTL adapter to connect to NSE01 and use AT Commands to configure it, as below.
148 148  
149 -[[image:image-20220606163915-7.png]]
150 150  
151 151  
152 -(% style="color:blue" %)**Step 3**(%%)**:** The LSE01 will auto join to the TTN network. After join success, it will start to upload messages to TTN and you can see the messages in the panel.
153 153  
154 -[[image:1654504778294-788.png]]
165 +Connection:
155 155  
167 + (% style="background-color:yellow" %)USB TTL GND <~-~-~-~-> GND
156 156  
169 + (% style="background-color:yellow" %)USB TTL TXD <~-~-~-~-> UART_RXD
157 157  
171 + (% style="background-color:yellow" %)USB TTL RXD <~-~-~-~-> UART_TXD
172 +
173 +
174 +
175 +In the PC, use below serial tool settings:
176 +
177 +* Baud: ** (% style="background-color:green" %)9600**(%%)
178 +* Data bits:** (% style="background-color:green" %)8**(%%)
179 +* Stop bits: **(% style="background-color:green" %)1**(%%)
180 +* Parity: **(% style="background-color:green" %)None**(%%)
181 +* Flow Control: **(% style="background-color:green" %)None**
182 +
183 +
184 +Make sure the switch is in FLASH position, then power on device by connecting the jumper on NSE01. NSE01 will output system info once power on as below, we can enter the **(% style="background-color:green" %)password: 12345678**(%%) to access AT Command input.
185 +
186 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image009.jpg]]
187 +
188 +Note: the valid AT Commands can be found at:
189 +
190 +[[http:~~/~~/www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/]]
191 +
192 +
193 +
194 +=== 2.2.4 Use CoAP protocol to uplink data === 
195 +
196 +
197 +(% style="background-color:red" %)Note: if you don’t have CoAP server, you can refer this link to set up one:
198 +
199 +[[http:~~/~~/wiki.dragino.com/index.php?title=Set_up_CoAP_Server>>url:http://wiki.dragino.com/index.php?title=Set_up_CoAP_Server]]
200 +
201 +
202 +Use below commands:
203 +
204 +* **(% style="color:blue" %)AT+PRO=1**  (%%)  ~/~/ Set to use CoAP protocol to uplink
205 +* **(% style="color:blue" %)AT+SERVADDR=120.24.4.116,5683   ** (%%)~/~/ to set CoAP server address and port
206 +* **(% style="color:blue" %)AT+URI=5,11,"mqtt",11,"coap",12,"0",15,"c=text1",23,"0" ** (%%)      ~/~/Set COAP resource path
207 +
208 +
209 +For parameter description, please refer to AT command set
210 +
211 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image011.jpg]]
212 +
213 +
214 +After configure the server address and **(% style="color:green" %)reset the device**(%%) (via AT+ATZ ), NSE01 will start to uplink sensor values to CoAP server.
215 +
216 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image013.jpg]]
217 +
218 +
219 +=== 2.2.5 Use UDP protocol to uplink data(Default protocol) ===
220 +
221 +
222 +This feature is supported since firmware version v1.0.1
223 +
224 +
225 +* **AT+PRO=2   ** ~/~/ Set to use UDP protocol to uplink
226 +* **AT+SERVADDR=120.24.4.116,5601   **~/~/ to set UDP server address and port
227 +* **AT+CFM=1       **~/~/If the server does not respond, this command is unnecessary
228 +
229 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image015.jpg]]
230 +
231 +
232 +
233 +
234 +
235 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image017.jpg]]
236 +
237 +
238 +1.
239 +11.
240 +111. Use MQTT protocol to uplink data
241 +
242 +
243 +This feature is supported since firmware version v110
244 +
245 +
246 +* **AT+PRO=3   ** ~/~/Set to use MQTT protocol to uplink
247 +* **AT+SERVADDR=120.24.4.116,1883   **~/~/Set MQTT server address and port
248 +* **AT+CLIENT=CLIENT **~/~/Set up the CLIENT of MQTT
249 +* **AT+UNAME=UNAME                           **~/~/Set the username of MQTT
250 +* **AT+PWD=PWD                                      **~/~/Set the password of MQTT
251 +* **AT+PUBTOPIC=NSE01_PUB   **~/~/Set the sending topic of MQTT
252 +* **AT+SUBTOPIC=NSE01_SUB    **~/~/Set the subscription topic of MQTT
253 +
254 +
255 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image019.gif]]
256 +
257 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image021.jpg]]
258 +
259 +
260 +MQTT protocol has a much higher power consumption compare vs UDP / CoAP protocol. Please check the power analyze document and adjust the uplink period to a suitable interval.
261 +
262 +
263 +1.
264 +11.
265 +111. Use TCP protocol to uplink data
266 +
267 +
268 +This feature is supported since firmware version v110
269 +
270 +
271 +* **AT+PRO=4   ** ~/~/ Set to use TCP protocol to uplink
272 +* **AT+SERVADDR=120.24.4.116,5600   **~/~/ to set TCP server address and port
273 +
274 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image023.jpg]]
275 +
276 +
277 +
278 +[[image:file:///C:/Users/93456/AppData/Local/Temp/msohtmlclip1/01/clip_image025.jpg]]
279 +
280 +
281 +1.
282 +11.
283 +111. Change Update Interval
284 +
285 +User can use below command to change the **uplink interval**.
286 +
287 +**~ AT+TDC=600      **~/~/ Set Update Interval to 600s
288 +
289 +
290 +**NOTE:**
291 +
292 +1. By default, the device will send an uplink message every 1 hour.
293 +
294 +
295 +
296 +
297 +
298 +
299 +
158 158  == 2.3 Uplink Payload ==
159 159  
160 160  
... ... @@ -327,7 +327,7 @@
327 327  
328 328  
329 329  (((
330 -**Examples:**
472 +(% style="color:blue" %)**Examples:**
331 331  )))
332 332  
333 333  (((
... ... @@ -335,7 +335,7 @@
335 335  )))
336 336  
337 337  * (((
338 -**Set TDC**
480 +(% style="color:blue" %)**Set TDC**
339 339  )))
340 340  
341 341  (((
... ... @@ -355,7 +355,7 @@
355 355  )))
356 356  
357 357  * (((
358 -**Reset**
500 +(% style="color:blue" %)**Reset**
359 359  )))
360 360  
361 361  (((
... ... @@ -363,7 +363,7 @@
363 363  )))
364 364  
365 365  
366 -* **CFM**
508 +* (% style="color:blue" %)**CFM**
367 367  
368 368  Downlink Payload: 05000001, Set AT+CFM=1 or 05000000 , set AT+CFM=0
369 369  
... ... @@ -694,7 +694,6 @@
694 694  * Solid ON for 5 seconds once device successful Join the network.
695 695  * Blink once when device transmit a packet.
696 696  
697 -
698 698  == 2.9 Installation in Soil ==
699 699  
700 700  **Measurement the soil surface**
... ... @@ -771,13 +771,13 @@
771 771  )))
772 772  
773 773  * (((
774 -[[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/&file=LSN50-Battery-Dimension.pdf]],
915 +[[Battery Dimension>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/]],
775 775  )))
776 776  * (((
777 -[[Lithium-Thionyl Chloride Battery  datasheet>>url:https://www.dragino.com/downloads/downloads/datasheet/Battery/ER26500/ER26500_Datasheet-EN.pdf]],
918 +[[Lithium-Thionyl Chloride Battery  datasheet>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/]],
778 778  )))
779 779  * (((
780 -[[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC_1520_datasheet.jpg]], [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC1520%20Technical%20Specification20171123.pdf]]
921 +[[Lithium-ion Battery-Capacitor datasheet>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/]], [[Tech Spec>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/]]
781 781  )))
782 782  
783 783   [[image:image-20220610172436-1.png]]
... ... @@ -1011,18 +1011,22 @@
1011 1011  [[image:image-20220606154825-4.png]]
1012 1012  
1013 1013  
1155 +== 4.2 ​Can I calibrate LSE01 to different soil types? ==
1014 1014  
1157 +LSE01 is calibrated for saline-alkali soil and loamy soil. If users want to use it for other soil, they can calibrate the value in the IoT platform base on the value measured by saline-alkali soil and loamy soil. The formula can be found at [[this link>>https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/&file=Calibrate_to_other_Soil_20220605.pdf]].
1158 +
1159 +
1015 1015  = 5. Trouble Shooting =
1016 1016  
1017 -== 5.1 ​Why I can’t join TTN in US915 / AU915 bands? ==
1162 +== 5.1 ​Why I can't join TTN in US915 / AU915 bands? ==
1018 1018  
1019 -It is due to channel mapping. Please see the [[Eight Channel Mode>>doc:Main.LoRaWAN Communication Debug.WebHome||anchor="H2.NoticeofUS9152FCN4702FAU915Frequencyband"]] section above for details.
1164 +It is due to channel mapping. Please see the [[Eight Channel Mode>>doc:Main.End Device AT Commands and Downlink Command.WebHome||anchor="H7.19EightChannelMode"]] section above for details.
1020 1020  
1021 1021  
1022 -== 5.2 AT Command input doesn’t work ==
1167 +== 5.2 AT Command input doesn't work ==
1023 1023  
1024 1024  (((
1025 -In the case if user can see the console output but can’t type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn’t send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
1170 +In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
1026 1026  )))
1027 1027  
1028 1028  
1657245163077-232.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +81.0 KB
Content
1657246476176-652.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +492.6 KB
Content
image-20220708101224-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +22.2 KB
Content
image-20220708101605-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +87.5 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0