Skip to Content
Version 65.5 by Xiaoling on 2022/07/08 15:14
Show last authors
1 (% style="text-align:center" %)
2 [[image:image-20220606151504-2.jpeg||height="554" width="554"]]
3
4
5
6
7
8
9
10
11
12
13
14 **Table of Contents:**
15
16 {{toc/}}
17
18
19
20
21
22
23 = 1.  Introduction =
24
25 == 1.1 ​ What is LoRaWAN Soil Moisture & EC Sensor ==
26
27 (((
28
29
30 Dragino NSE01 is an (% style="color:blue" %)**NB-IOT soil moisture & EC sensor**(%%) for agricultural IoT. Used to measure the soil moisture of saline-alkali soil and loam. The soil sensor uses the FDR method to calculate soil moisture and compensates it with soil temperature and electrical conductivity. It has also been calibrated for mineral soil types at the factory.
31
32 It can detect (% style="color:blue" %)**Soil Moisture, Soil Temperature and Soil Conductivity**(%%), and upload its value to the server wirelessly.
33
34 The wireless technology used in NSE01 allows the device to send data at a low data rate and reach ultra-long distances, providing ultra-long-distance spread spectrum Communication.
35
36 NSE01 are powered by (% style="color:blue" %)**8500mAh Li-SOCI2**(%%) batteries, which can be used for up to 5 years.  
37
38
39 )))
40
41 [[image:1654503236291-817.png]]
42
43
44 [[image:1657245163077-232.png]]
45
46
47
48 == 1.2 ​ Features ==
49
50 * NB-IoT Bands: B1/B3/B8/B5/B20/B28 @H-FDD
51 * Monitor Soil Moisture
52 * Monitor Soil Temperature
53 * Monitor Soil Conductivity
54 * AT Commands to change parameters
55 * Uplink on periodically
56 * Downlink to change configure
57 * IP66 Waterproof Enclosure
58 * Ultra-Low Power consumption
59 * AT Commands to change parameters
60 * Micro SIM card slot for NB-IoT SIM
61 * 8500mAh Battery for long term use
62
63
64
65 == 1.3  Specification ==
66
67
68 (% style="color:#037691" %)**Common DC Characteristics:**
69
70 * Supply Voltage: 2.1v ~~ 3.6v
71 * Operating Temperature: -40 ~~ 85°C
72
73
74 (% style="color:#037691" %)**NB-IoT Spec:**
75
76 * - B1 @H-FDD: 2100MHz
77 * - B3 @H-FDD: 1800MHz
78 * - B8 @H-FDD: 900MHz
79 * - B5 @H-FDD: 850MHz
80 * - B20 @H-FDD: 800MHz
81 * - B28 @H-FDD: 700MHz
82
83
84 Probe(% style="color:#037691" %)** Specification:**
85
86 Measure Volume: Base on the centra pin of the probe, a cylinder with 7cm diameter and 10cm height.
87
88 [[image:image-20220708101224-1.png]]
89
90
91
92 == ​1.4  Applications ==
93
94 * Smart Agriculture
95
96 (% class="wikigeneratedid" id="H200B1.5FirmwareChangelog" %)
97 ​
98
99 == 1.5  Pin Definitions ==
100
101
102 [[image:1657246476176-652.png]]
103
104
105
106 = 2.  Use NSE01 to communicate with IoT Server =
107
108 == 2.1  How it works ==
109
110
111 (((
112 The NSE01 is equipped with a NB-IoT module, the pre-loaded firmware in NSE01 will get environment data from sensors and send the value to local NB-IoT network via the NB-IoT module.  The NB-IoT network will forward this value to IoT server via the protocol defined by NSE01.
113 )))
114
115
116 (((
117 The diagram below shows the working flow in default firmware of NSE01:
118 )))
119
120 [[image:image-20220708101605-2.png]]
121
122 (((
123
124 )))
125
126
127
128 == 2.2 ​ Configure the NSE01 ==
129
130
131 === 2.2.1 Test Requirement ===
132
133
134 To use NSE01 in your city, make sure meet below requirements:
135
136 * Your local operator has already distributed a NB-IoT Network there.
137 * The local NB-IoT network used the band that NSE01 supports.
138 * Your operator is able to distribute the data received in their NB-IoT network to your IoT server.
139
140 (((
141 Below figure shows our testing structure. Here we have NB-IoT network coverage by China Mobile, the band they use is B8.  The NSE01 will use CoAP((% style="color:red" %)120.24.4.116:5683)(%%) or raw UDP((% style="color:red" %)120.24.4.116:5601)(%%) or MQTT((% style="color:red" %)120.24.4.116:1883)(%%)or TCP((% style="color:red" %)120.24.4.116:5600)(%%)protocol to send data to the test server
142 )))
143
144
145 [[image:1657249419225-449.png]]
146
147
148
149 === 2.2.2 Insert SIM card ===
150
151 Insert the NB-IoT Card get from your provider.
152
153 User need to take out the NB-IoT module and insert the SIM card like below:
154
155
156 [[image:1657249468462-536.png]]
157
158
159
160 === 2.2.3 Connect USB – TTL to NSE01 to configure it ===
161
162 (((
163 (((
164 User need to configure NSE01 via serial port to set the (% style="color:blue" %)**Server Address** / **Uplink Topic** (%%)to define where and how-to uplink packets. NSE01 support AT Commands, user can use a USB to TTL adapter to connect to NSE01 and use AT Commands to configure it, as below.
165 )))
166 )))
167
168
169 **Connection:**
170
171 (% style="background-color:yellow" %)USB TTL GND <~-~-~-~-> GND
172
173 (% style="background-color:yellow" %)USB TTL TXD <~-~-~-~-> UART_RXD
174
175 (% style="background-color:yellow" %)USB TTL RXD <~-~-~-~-> UART_TXD
176
177
178 In the PC, use below serial tool settings:
179
180 * Baud:  (% style="color:green" %)**9600**
181 * Data bits:** (% style="color:green" %)8(%%)**
182 * Stop bits: (% style="color:green" %)**1**
183 * Parity:  (% style="color:green" %)**None**
184 * Flow Control: (% style="color:green" %)**None**
185
186 (((
187 Make sure the switch is in FLASH position, then power on device by connecting the jumper on NSE01. NSE01 will output system info once power on as below, we can enter the (% style="color:green" %)**password: 12345678**(%%) to access AT Command input.
188 )))
189
190 [[image:image-20220708110657-3.png]]
191
192 (% style="color:red" %)Note: the valid AT Commands can be found at: (%%)[[http:~~/~~/www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/]]
193
194
195
196 === 2.2.4 Use CoAP protocol to uplink data ===
197
198 (% style="color:red" %)Note: if you don't have CoAP server, you can refer this link to set up one: (%%)[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/>>http://wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/]]
199
200
201 **Use below commands:**
202
203 * (% style="color:blue" %)**AT+PRO=1**  (%%) ~/~/ Set to use CoAP protocol to uplink
204 * (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5683   ** (%%)~/~/ to set CoAP server address and port
205 * (% style="color:blue" %)**AT+URI=5,11,"mqtt",11,"coap",12,"0",15,"c=text1",23,"0" ** (%%) ~/~/Set COAP resource path
206
207 For parameter description, please refer to AT command set
208
209 [[image:1657249793983-486.png]]
210
211
212 After configure the server address and (% style="color:green" %)**reset the device**(%%) (via AT+ATZ ), NSE01 will start to uplink sensor values to CoAP server.
213
214 [[image:1657249831934-534.png]]
215
216
217
218 === 2.2.5 Use UDP protocol to uplink data(Default protocol) ===
219
220 This feature is supported since firmware version v1.0.1
221
222
223 * (% style="color:blue" %)**AT+PRO=2   ** (%%) ~/~/ Set to use UDP protocol to uplink
224 * (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5601   ** (%%) ~/~/ to set UDP server address and port
225 * (% style="color:blue" %)**AT+CFM=1       ** (%%) ~/~/If the server does not respond, this command is unnecessary
226
227 [[image:1657249864775-321.png]]
228
229
230 [[image:1657249930215-289.png]]
231
232
233
234 === 2.2.6 Use MQTT protocol to uplink data ===
235
236 This feature is supported since firmware version v110
237
238
239 * (% style="color:blue" %)**AT+PRO=3   ** (%%) ~/~/Set to use MQTT protocol to uplink
240 * (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,1883   ** (%%) ~/~/Set MQTT server address and port
241 * (% style="color:blue" %)**AT+CLIENT=CLIENT       ** (%%)~/~/Set up the CLIENT of MQTT
242 * (% style="color:blue" %)**AT+UNAME=UNAME                               **(%%)~/~/Set the username of MQTT
243 * (% style="color:blue" %)**AT+PWD=PWD                                        **(%%)~/~/Set the password of MQTT
244 * (% style="color:blue" %)**AT+PUBTOPIC=NSE01_PUB                    **(%%)~/~/Set the sending topic of MQTT
245 * (% style="color:blue" %)**AT+SUBTOPIC=NSE01_SUB          **(%%) ~/~/Set the subscription topic of MQTT
246
247 [[image:1657249978444-674.png]]
248
249
250 [[image:1657249990869-686.png]]
251
252
253 (((
254 MQTT protocol has a much higher power consumption compare vs UDP / CoAP protocol. Please check the power analyze document and adjust the uplink period to a suitable interval.
255 )))
256
257
258
259 === 2.2.7 Use TCP protocol to uplink data ===
260
261 This feature is supported since firmware version v110
262
263
264 * (% style="color:blue" %)**AT+PRO=4   ** (%%) ~/~/ Set to use TCP protocol to uplink
265 * (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5600   **(%%) ~/~/ to set TCP server address and port
266
267 [[image:1657250217799-140.png]]
268
269
270 [[image:1657250255956-604.png]]
271
272
273
274 === 2.2.8 Change Update Interval ===
275
276 User can use below command to change the (% style="color:green" %)**uplink interval**.
277
278 * (% style="color:blue" %)**AT+TDC=600      ** (%%)~/~/ Set Update Interval to 600s
279
280 (((
281 (% style="color:red" %)**NOTE:**
282 )))
283
284 (((
285 (% style="color:red" %)1. By default, the device will send an uplink message every 1 hour.
286 )))
287
288
289
290 == 2.3  Uplink Payload ==
291
292 In this mode, uplink payload includes in total 18 bytes
293
294 (% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:510px" %)
295 |=(% style="width: 50px;" %)(((
296 **Size(bytes)**
297 )))|=(% style="width: 50px;" %)**6**|=(% style="width: 25px;" %)2|=(% style="width: 25px;" %)**2**|=(% style="width: 80px;" %)**1**|=(% style="width: 80px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 40px;" %)**1**
298 |(% style="width:97px" %)**Value**|(% style="width:83px" %)[[Device ID>>||anchor="H2.4.1A0A0DeviceID"]]|(% style="width:41px" %)[[Ver>>||anchor="H2.4.2A0VersionInfo"]]|(% style="width:46px" %)[[BAT>>||anchor="H2.4.3A0BatteryInfo"]]|(% style="width:123px" %)[[Signal Strength>>||anchor="H2.4.4A0SignalStrength"]]|(% style="width:108px" %)[[Soil Moisture>>||anchor="H2.4.5A0SoilMoisture"]]|(% style="width:133px" %)[[Soil Temperature>>||anchor="H2.4.6A0SoilTemperature"]]|(% style="width:159px" %)[[Soil Conductivity(EC)>>||anchor="H2.4.7A0SoilConductivity28EC29"]]|(% style="width:80px" %)[[Interrupt>>||anchor="H2.4.8A0DigitalInterrupt"]]
299
300 If we use the MQTT client to subscribe to this MQTT topic, we can see the following information when the NSE01 uplink data.
301
302
303 [[image:image-20220708111918-4.png]]
304
305
306 The payload is ASCII string, representative same HEX:
307
308 0x72403155615900640c7817075e0a8c02f900 where:
309
310 * Device ID: 0x 724031556159 = 724031556159
311 * Version: 0x0064=100=1.0.0
312
313 * BAT: 0x0c78 = 3192 mV = 3.192V
314 * Singal: 0x17 = 23
315 * Soil Moisture: 0x075e= 1886 = 18.86  %
316 * Soil Temperature:0x0a8c =2700=27 °C
317 * Soil Conductivity(EC) = 0x02f9 =761 uS /cm
318 * Interrupt: 0x00 = 0
319
320
321
322 == 2.4  Payload Explanation and Sensor Interface ==
323
324
325 === 2.4.1  Device ID ===
326
327 By default, the Device ID equal to the last 6 bytes of IMEI.
328
329 User can use (% style="color:blue" %)**AT+DEUI**(%%) to set Device ID
330
331 **Example:**
332
333 AT+DEUI=A84041F15612
334
335 The Device ID is stored in a none-erase area, Upgrade the firmware or run AT+FDR won't erase Device ID.
336
337
338
339 === 2.4.2  Version Info ===
340
341 Specify the software version: 0x64=100, means firmware version 1.00.
342
343 For example: 0x00 64 : this device is NSE01 with firmware version 1.0.0.
344
345
346
347 === 2.4.3  Battery Info ===
348
349 (((
350 Check the battery voltage for LSE01.
351 )))
352
353 (((
354 Ex1: 0x0B45 = 2885mV
355 )))
356
357 (((
358 Ex2: 0x0B49 = 2889mV
359 )))
360
361
362
363 === 2.4.4  Signal Strength ===
364
365 NB-IoT Network signal Strength.
366
367 **Ex1: 0x1d = 29**
368
369 (% style="color:blue" %)**0**(%%)  -113dBm or less
370
371 (% style="color:blue" %)**1**(%%)  -111dBm
372
373 (% style="color:blue" %)**2...30**(%%) -109dBm... -53dBm
374
375 (% style="color:blue" %)**31**  (%%) -51dBm or greater
376
377 (% style="color:blue" %)**99**   (%%) Not known or not detectable
378
379
380
381 === 2.4.5  Soil Moisture ===
382
383 (((
384 Get the moisture content of the soil. The value range of the register is 0-10000(Decimal), divide this value by 100 to get the percentage of moisture in the soil.
385 )))
386
387 (((
388 For example, if the data you get from the register is **__0x05 0xDC__**, the moisture content in the soil is
389 )))
390
391 (((
392
393 )))
394
395 (((
396 (% style="color:#4f81bd" %)**05DC(H) = 1500(D) /100 = 15%.**
397 )))
398
399
400
401 === 2.4.6  Soil Temperature ===
402
403 (((
404 Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is __**0x09 0xEC**__, the temperature content in the soil is
405 )))
406
407 (((
408 **Example**:
409 )))
410
411 (((
412 If payload is 0105H: ((0x0105 & 0x8000)>>15 === 0),temp = 0105(H)/100 = 2.61 °C
413 )))
414
415 (((
416 If payload is FF7EH: ((FF7E & 0x8000)>>15 ===1),temp = (FF7E(H)-FFFF(H))/100 = -1.29 °C
417 )))
418
419
420
421 === 2.4.7  Soil Conductivity (EC) ===
422
423 (((
424 Obtain (% style="color:#4f81bd" %)**__soluble salt concentration__**(%%) in soil or (% style="color:#4f81bd" %)**__soluble ion concentration in liquid fertilizer__**(%%) or (% style="color:#4f81bd" %)**__planting medium__**(%%). The value range of the register is 0 - 20000(Decimal)( Can be greater than 20000).
425 )))
426
427 (((
428 For example, if the data you get from the register is __**0x00 0xC8**__, the soil conductivity is 00C8(H) = 200(D) = 200 uS/cm.
429 )))
430
431 (((
432 Generally, the EC value of irrigation water is less than 800uS / cm.
433 )))
434
435 (((
436
437 )))
438
439 (((
440
441 )))
442
443 === 2.4.8  Digital Interrupt ===
444
445 Digital Interrupt refers to pin (% style="color:blue" %)**GPIO_EXTI**(%%), and there are different trigger methods. When there is a trigger, the NSE01 will send a packet to the server.
446
447 The command is:
448
449 (% style="color:blue" %)**AT+INTMOD=3 **(%%) ~/~/(more info about INMOD please refer [[**AT Command Manual**>>url:https://www.dragino.com/downloads/downloads/NB-IoT/NBSN95/DRAGINO_NBSN95-NB_AT%20Commands_v1.1.0.pdf]])**.**
450
451
452 The lower four bits of this data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H"]] for the hardware and software set up.
453
454
455 Example:
456
457 0x(00): Normal uplink packet.
458
459 0x(01): Interrupt Uplink Packet.
460
461
462
463 === 2.4.9  ​+5V Output ===
464
465 NSE01 will enable +5V output before all sampling and disable the +5v after all sampling. 
466
467
468 The 5V output time can be controlled by AT Command.
469
470 (% style="color:blue" %)**AT+5VT=1000**
471
472 Means set 5V valid time to have 1000ms. So the real 5V output will actually have 1000ms + sampling time for other sensors.
473
474
475
476 == 2.5  Downlink Payload ==
477
478 By default, NSE01 prints the downlink payload to console port.
479
480 [[image:image-20220708133731-5.png]]
481
482
483 (((
484 (% style="color:blue" %)**Examples:**
485 )))
486
487 (((
488
489 )))
490
491 * (((
492 (% style="color:blue" %)**Set TDC**
493 )))
494
495 (((
496 If the payload=0100003C, it means set the END Node's TDC to 0x00003C=60(S), while type code is 01.
497 )))
498
499 (((
500 Payload:    01 00 00 1E    TDC=30S
501 )))
502
503 (((
504 Payload:    01 00 00 3C    TDC=60S
505 )))
506
507 (((
508
509 )))
510
511 * (((
512 (% style="color:blue" %)**Reset**
513 )))
514
515 (((
516 If payload = 0x04FF, it will reset the NSE01
517 )))
518
519
520 * (% style="color:blue" %)**INTMOD**
521
522 Downlink Payload: 06000003, Set AT+INTMOD=3
523
524
525
526 == 2.6  ​LED Indicator ==
527
528 (((
529 The NSE01 has an internal LED which is to show the status of different state.
530
531
532 * When power on, NSE01 will detect if sensor probe is connected, if probe detected, LED will blink four times. (no blinks in this step is no probe)
533 * Then the LED will be on for 1 second means device is boot normally.
534 * After NSE01 join NB-IoT network. The LED will be ON for 3 seconds.
535 * For each uplink probe, LED will be on for 500ms.
536 )))
537
538
539
540
541 == 2.7  Installation in Soil ==
542
543 __**Measurement the soil surface**__
544
545 Choose the proper measuring position. Avoid the probe to touch rocks or hard things. Split the surface soil according to the measured deep. Keep the measured as original density. Vertical insert the probe into the soil to be measured. Make sure not shake when inserting. [[https:~~/~~/img.alicdn.com/imgextra/i3/2005165265/O1CN010rj9Oh1olPsQxrdUK_!!2005165265.jpg>>url:https://img.alicdn.com/imgextra/i3/2005165265/O1CN010rj9Oh1olPsQxrdUK_!!2005165265.jpg]]
546
547 [[image:1657259653666-883.png]] ​
548
549
550 (((
551
552
553 (((
554 Dig a hole with diameter > 20CM.
555 )))
556
557 (((
558 Horizontal insert the probe to the soil and fill the hole for long term measurement.
559 )))
560 )))
561
562 [[image:1654506665940-119.png]]
563
564 (((
565
566 )))
567
568
569 == 2.8  ​Firmware Change Log ==
570
571
572 Download URL & Firmware Change log
573
574 [[www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/Firmware/]]
575
576
577 Upgrade Instruction: [[Upgrade_Firmware>>||anchor="H"]]
578
579
580
581 == 2.9  ​Battery Analysis ==
582
583 === 2.9.1  ​Battery Type ===
584
585
586 The NSE01 battery is a combination of an 8500mAh Li/SOCI2 Battery and a Super Capacitor. The battery is none-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
587
588
589 The battery is designed to last for several years depends on the actually use environment and update interval. 
590
591
592 The battery related documents as below:
593
594 * [[Battery Dimension>>http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
595 * [[Lithium-Thionyl Chloride Battery>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]][[ datasheet>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
596 * [[Lithium-ion Battery-Capacitor datasheet>>http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
597
598 (((
599 [[image:image-20220708140453-6.png]]
600 )))
601
602
603
604 === 2.9.2  Power consumption Analyze ===
605
606 (((
607 Dragino battery powered product are all runs in Low Power mode. We have an update battery calculator which base on the measurement of the real device. User can use this calculator to check the battery life and calculate the battery life if want to use different transmit interval.
608 )))
609
610
611 (((
612 Instruction to use as below:
613 )))
614
615 (((
616 (% style="color:blue" %)**Step 1:  **(%%)Downlink the up-to-date DRAGINO_Battery_Life_Prediction_Table.xlsx from: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/>>url:https://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/Battery_Analyze/]]
617 )))
618
619
620 (((
621 (% style="color:blue" %)**Step 2: **(%%) Open it and choose
622 )))
623
624 * (((
625 Product Model
626 )))
627 * (((
628 Uplink Interval
629 )))
630 * (((
631 Working Mode
632 )))
633
634 (((
635 And the Life expectation in difference case will be shown on the right.
636 )))
637
638 [[image:image-20220708141352-7.jpeg]]
639
640
641
642 === 2.9.3  ​Battery Note ===
643
644 (((
645 The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
646 )))
647
648
649
650 === 2.9.4  Replace the battery ===
651
652 (((
653 The default battery pack of NSE01 includes a ER26500 plus super capacitor. If user can't find this pack locally, they can find ER26500 or equivalence without the SPC1520 capacitor, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes).
654 )))
655
656
657
658 = 3. ​ Access NB-IoT Module =
659
660 (((
661 Users can directly access the AT command set of the NB-IoT module.
662 )))
663
664 (((
665 The AT Command set can refer the BC35-G NB-IoT Module AT Command: [[https:~~/~~/www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/>>url:https://www.dragino.com/downloads/index.php?dir=datasheet/other_vendors/BC35-G/]] 
666 )))
667
668 [[image:1657261278785-153.png]]
669
670
671
672 = 4.  Using the AT Commands =
673
674 == 4.1  Access AT Commands ==
675
676 See this link for detail: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/]]
677
678
679 AT+<CMD>?  : Help on <CMD>
680
681 AT+<CMD>         : Run <CMD>
682
683 AT+<CMD>=<value> : Set the value
684
685 AT+<CMD>=?  : Get the value
686
687
688 (% style="color:#037691" %)**General Commands**(%%)      
689
690 AT  : Attention       
691
692 AT?  : Short Help     
693
694 ATZ  : MCU Reset    
695
696 AT+TDC  : Application Data Transmission Interval
697
698 AT+CFG  : Print all configurations
699
700 AT+CFGMOD           : Working mode selection
701
702 AT+INTMOD            : Set the trigger interrupt mode
703
704 AT+5VT  : Set extend the time of 5V power  
705
706 AT+PRO  : Choose agreement
707
708 AT+WEIGRE  : Get weight or set weight to 0
709
710 AT+WEIGAP  : Get or Set the GapValue of weight
711
712 AT+RXDL  : Extend the sending and receiving time
713
714 AT+CNTFAC  : Get or set counting parameters
715
716 AT+SERVADDR  : Server Address
717
718
719 (% style="color:#037691" %)**COAP Management**      
720
721 AT+URI            : Resource parameters
722
723
724 (% style="color:#037691" %)**UDP Management**
725
726 AT+CFM          : Upload confirmation mode (only valid for UDP)
727
728
729 (% style="color:#037691" %)**MQTT Management**
730
731 AT+CLIENT               : Get or Set MQTT client
732
733 AT+UNAME  : Get or Set MQTT Username
734
735 AT+PWD                  : Get or Set MQTT password
736
737 AT+PUBTOPIC  : Get or Set MQTT publish topic
738
739 AT+SUBTOPIC  : Get or Set MQTT subscription topic
740
741
742 (% style="color:#037691" %)**Information**          
743
744 AT+FDR  : Factory Data Reset
745
746 AT+PWORD  : Serial Access Password
747
748
749
750 = ​5.  FAQ =
751
752 == 5.1 ​ How to Upgrade Firmware ==
753
754
755 (((
756 User can upgrade the firmware for 1) bug fix, 2) new feature release.
757 )))
758
759 (((
760 Please see this link for how to upgrade:  [[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList>>http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H2.HardwareUpgradeMethodSupportList]]
761 )))
762
763 (((
764 (% style="color:red" %)Notice, NSE01 and LSE01 share the same mother board. They use the same connection and method to update.
765 )))
766
767
768
769 = 6.  Trouble Shooting =
770
771 == 6.1  ​Connection problem when uploading firmware ==
772
773
774 (% class="wikigeneratedid" %)
775 (((
776 (% style="font-size:14px" %)**Please see: **(%%)[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting>>http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting||style="background-color: rgb(255, 255, 255); font-size: 14px;"]]
777 )))
778
779
780
781 == 6.2  AT Command input doesn't work ==
782
783 (((
784 In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
785 )))
786
787
788
789 = 7. ​ Order Info =
790
791
792 Part Number**:** (% style="color:#4f81bd" %)**NSE01**
793
794
795 (% class="wikigeneratedid" %)
796 (((
797
798 )))
799
800 = 8.  Packing Info =
801
802 (((
803
804
805 (% style="color:#037691" %)**Package Includes**:
806
807
808 * NSE01 NB-IoT Soil Moisture & EC Sensor x 1
809 * External antenna x 1
810 )))
811
812 (((
813
814
815 (% style="color:#037691" %)**Dimension and weight**:
816
817
818 * Size: 195 x 125 x 55 mm
819 * Weight:   420g
820 )))
821
822 (((
823
824
825
826
827 )))
828
829 = 9.  Support =
830
831 * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
832 * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]