Wiki source code of LSE01-LoRaWAN Soil Moisture & EC Sensor User Manual

Version 35.10 by Xiaoling on 2022/06/14 14:04

version	line-number	content
4.2	1	(% style="text-align:center" %)
31.14	2	[[image:image-20220606151504-2.jpeg\|\|height="554" width="554"]]
1.1	3
	4
	5
35.4	6	Table of Contents:
1.1	7
31.17	8	{{toc/}}
1.1	9
	10
	11
	12
31.17	13
	14
12.2	15	= 1. Introduction =
1.1	16
12.2	17	== 1.1 What is LoRaWAN Soil Moisture & EC Sensor ==
1.1	18
12.2	19	(((
35.4	20
	21
12.2	22	The Dragino LSE01 is a (% style="color:#4f81bd" %)LoRaWAN Soil Moisture & EC Sensor(%%) for IoT of Agriculture. It is designed to measure the soil moisture of saline-alkali soil and loamy soil. The soil sensor uses FDR method to calculate the soil moisture with the compensation from soil temperature and conductivity. It also has been calibrated in factory for Mineral soil type.
	23	)))
1.1	24
12.2	25	(((
	26	It detects (% style="color:#4f81bd" %)Soil Moisture(%%), (% style="color:#4f81bd" %)Soil Temperature(%%) and (% style="color:#4f81bd" %)Soil Conductivity(%%), and uploads the value via wireless to LoRaWAN IoT Server.
	27	)))
1.1	28
12.2	29	(((
4.2	30	The LoRa wireless technology used in LES01 allows device to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption.
12.2	31	)))
4.2	32
12.2	33	(((
	34	LES01 is powered by (% style="color:#4f81bd" %)4000mA or 8500mAh Li-SOCI2 battery(%%), It is designed for long term use up to 10 years.
	35	)))
4.2	36
12.2	37	(((
4.2	38	Each LES01 is pre-load with a set of unique keys for LoRaWAN registrations, register these keys to local LoRaWAN server and it will auto connect after power on.
12.2	39	)))
4.2	40
	41
12.2	42	[[image:1654503236291-817.png]]
4.2	43
	44
13.2	45	[[image:1654503265560-120.png]]
4.2	46
	47
	48
13.3	49	== 1.2 Features ==
	50
4.2	51	* LoRaWAN 1.0.3 Class A
	52	* Ultra low power consumption
	53	* Monitor Soil Moisture
	54	* Monitor Soil Temperature
	55	* Monitor Soil Conductivity
	56	* Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915/IN865
	57	* AT Commands to change parameters
	58	* Uplink on periodically
	59	* Downlink to change configure
	60	* IP66 Waterproof Enclosure
	61	* 4000mAh or 8500mAh Battery for long term use
	62
33.2	63
35.4	64
13.3	65	== 1.3 Specification ==
	66
4.2	67	Measure Volume: Base on the centra pin of the probe, a cylinder with 7cm diameter and 10cm height.
	68
14.2	69	[[image:image-20220606162220-5.png]]
	70
4.2	71
	72
14.3	73	== 1.4 Applications ==
4.2	74
	75	* Smart Agriculture
	76
15.6	77	(% class="wikigeneratedid" id="H200B1.5FirmwareChangelog" %)
	78
4.2	79
15.6	80	== 1.5 Firmware Change log ==
	81
	82
14.3	83	LSE01 v1.0 : Release
4.2	84
14.3	85
	86
	87	= 2. Configure LSE01 to connect to LoRaWAN network =
	88
	89	== 2.1 How it works ==
	90
15.3	91	(((
4.2	92	The LSE01 is configured as LoRaWAN OTAA Class A mode by default. It has OTAA keys to join LoRaWAN network. To connect a local LoRaWAN network, you need to input the OTAA keys in the LoRaWAN IoT server and power on the LSE0150. It will automatically join the network via OTAA and start to send the sensor value
15.3	93	)))
4.2	94
15.3	95	(((
31.33	96	In case you can’t set the OTAA keys in the LoRaWAN OTAA server, and you have to use the keys from the server, you can [[use AT Commands >>\|\|anchor="H3.200BUsingtheATCommands"]].
15.3	97	)))
4.2	98
	99
	100
14.4	101	== 2.2 Quick guide to connect to LoRaWAN server (OTAA) ==
4.2	102
	103	Following is an example for how to join the [[TTN v3 LoRaWAN Network>>url:https://console.cloud.thethings.network/]]. Below is the network structure; we use the [[LG308>>url:http://www.dragino.com/products/lora/item/140-lg308.html]] as a LoRaWAN gateway in this example.
	104
	105
15.2	106	[[image:1654503992078-669.png]]
4.2	107
	108
	109	The LG308 is already set to connected to [[TTN network >>url:https://console.cloud.thethings.network/]], so what we need to now is configure the TTN server.
	110
	111
35.8	112	(% style="color:blue" %)Step 1(%%): Create a device in TTN with the OTAA keys from LSE01.
4.2	113
	114	Each LSE01 is shipped with a sticker with the default device EUI as below:
	115
17.2	116	[[image:image-20220606163732-6.jpeg]]
4.2	117
	118	You can enter this key in the LoRaWAN Server portal. Below is TTN screen shot:
	119
	120	Add APP EUI in the application
	121
	122
17.2	123	[[image:1654504596150-405.png]]
4.2	124
	125
	126
	127	Add APP KEY and DEV EUI
	128
18.2	129	[[image:1654504683289-357.png]]
4.2	130
	131
19.2	132
35.8	133	(% style="color:blue" %)Step 2(%%): Power on LSE01
4.2	134
	135
	136	Put a Jumper on JP2 to power on the device. ( The Jumper must be in FLASH position).
	137
19.2	138	[[image:image-20220606163915-7.png]]
4.2	139
	140
35.8	141	(% style="color:blue" %)Step 3(%%): The LSE01 will auto join to the TTN network. After join success, it will start to upload messages to TTN and you can see the messages in the panel.
4.2	142
20.2	143	[[image:1654504778294-788.png]]
4.2	144
	145
	146
20.3	147	== 2.3 Uplink Payload ==
4.2	148
32.9	149
20.3	150	=== 2.3.1 MOD~=0(Default Mode) ===
4.2	151
4.4	152	LSE01 will uplink payload via LoRaWAN with below payload format:
4.2	153
32.9	154	(((
4.2	155	Uplink payload includes in total 11 bytes.
32.9	156	)))
4.2	157
32.3	158	(% border="1" cellspacing="10" style="background-color:#ffffcc; width:500px" %)
	159	\|(((
4.2	160	Size
	161
	162	(bytes)
32.3	163	)))\|2\|2\|2\|2\|2\|1
32.4	164	\|Value\|[[BAT>>\|\|anchor="H2.3.3BatteryInfo"]]\|(((
4.2	165	Temperature
	166
	167	(Reserve, Ignore now)
32.4	168	)))\|[[Soil Moisture>>\|\|anchor="H2.3.4SoilMoisture"]]\|[[Soil Temperature>>\|\|anchor="H2.3.5SoilTemperature"]]\|[[Soil Conductivity (EC)>>\|\|anchor="H2.3.6SoilConductivity28EC29"]]\|(((
4.2	169	MOD & Digital Interrupt
	170
	171	(Optional)
	172	)))
	173
35.9	174
	175
	176
	177
22.2	178	=== 2.3.2 MOD~=1(Original value) ===
	179
4.2	180	This mode can get the original AD value of moisture and original conductivity (with temperature drift compensation).
	181
32.3	182	(% border="1" cellspacing="10" style="background-color:#ffffcc; width:500px" %)
	183	\|(((
4.2	184	Size
	185
	186	(bytes)
32.3	187	)))\|2\|2\|2\|2\|2\|1
32.4	188	\|Value\|[[BAT>>\|\|anchor="H2.3.3BatteryInfo"]]\|(((
4.2	189	Temperature
	190
	191	(Reserve, Ignore now)
32.4	192	)))\|[[Soil Moisture>>\|\|anchor="H2.3.4SoilMoisture"]](raw)\|[[Soil Temperature>>\|\|anchor="H2.3.5SoilTemperature"]]\|[[Soil Conductivity (EC)>>\|\|anchor="H2.3.6SoilConductivity28EC29"]](raw)\|(((
4.2	193	MOD & Digital Interrupt
	194
	195	(Optional)
	196	)))
	197
35.10	198
	199
	200
	201
22.2	202	=== 2.3.3 Battery Info ===
	203
32.10	204	(((
4.2	205	Check the battery voltage for LSE01.
32.10	206	)))
4.2	207
32.10	208	(((
4.2	209	Ex1: 0x0B45 = 2885mV
32.10	210	)))
4.2	211
32.10	212	(((
4.2	213	Ex2: 0x0B49 = 2889mV
32.10	214	)))
4.2	215
	216
	217
22.3	218	=== 2.3.4 Soil Moisture ===
4.2	219
32.10	220	(((
4.2	221	Get the moisture content of the soil. The value range of the register is 0-10000(Decimal), divide this value by 100 to get the percentage of moisture in the soil.
32.10	222	)))
4.2	223
32.10	224	(((
22.4	225	For example, if the data you get from the register is __0x05 0xDC__, the moisture content in the soil is
32.10	226	)))
4.2	227
32.10	228	(((
	229
	230	)))
4.2	231
32.10	232	(((
22.4	233	(% style="color:#4f81bd" %)05DC(H) = 1500(D) /100 = 15%.
32.10	234	)))
4.2	235
22.4	236
4.2	237
22.5	238	=== 2.3.5 Soil Temperature ===
	239
32.11	240	(((
4.2	241	Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is 0x09 0xEC, the temperature content in the soil is
32.11	242	)))
4.2	243
32.11	244	(((
4.2	245	Example:
32.11	246	)))
4.2	247
32.11	248	(((
4.2	249	If payload is 0105H: ((0x0105 & 0x8000)>>15 === 0),temp = 0105(H)/100 = 2.61 °C
32.11	250	)))
4.2	251
32.11	252	(((
4.2	253	If payload is FF7EH: ((FF7E & 0x8000)>>15 ===1),temp = (FF7E(H)-FFFF(H))/100 = -1.29 °C
32.11	254	)))
4.2	255
	256
	257
22.6	258	=== 2.3.6 Soil Conductivity (EC) ===
	259
23.2	260	(((
	261	Obtain (% style="color:#4f81bd" %)__soluble salt concentration__(%%) in soil or (% style="color:#4f81bd" %)__soluble ion concentration in liquid fertilizer__(%%) or (% style="color:#4f81bd" %)__planting medium__(%%). The value range of the register is 0 - 20000(Decimal)( Can be greater than 20000).
	262	)))
4.2	263
23.2	264	(((
4.2	265	For example, if the data you get from the register is 0x00 0xC8, the soil conductivity is 00C8(H) = 200(D) = 200 uS/cm.
23.2	266	)))
4.2	267
23.2	268	(((
4.2	269	Generally, the EC value of irrigation water is less than 800uS / cm.
23.2	270	)))
4.2	271
23.2	272	(((
	273
	274	)))
4.2	275
23.2	276	(((
	277
	278	)))
	279
	280	=== 2.3.7 MOD ===
	281
4.2	282	Firmware version at least v2.1 supports changing mode.
	283
	284	For example, bytes[10]=90
	285
	286	mod=(bytes[10]>>7)&0x01=1.
	287
	288
31.23	289	Downlink Command:
4.2	290
	291	If payload = 0x0A00, workmode=0
	292
	293	If payload = 0x0A01, workmode=1
	294
	295
	296
23.2	297	=== 2.3.8 Decode payload in The Things Network ===
	298
4.2	299	While using TTN network, you can add the payload format to decode the payload.
	300
	301
23.2	302	[[image:1654505570700-128.png]]
4.2	303
32.12	304	(((
4.2	305	The payload decoder function for TTN is here:
32.12	306	)))
4.2	307
32.12	308	(((
4.2	309	LSE01 TTN Payload Decoder: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Payload_Decoder/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Payload_Decoder/]]
32.12	310	)))
4.2	311
	312
31.27	313
23.3	314	== 2.4 Uplink Interval ==
4.2	315
31.26	316	The LSE01 by default uplink the sensor data every 20 minutes. User can change this interval by AT Command or LoRaWAN Downlink Command. See this link: [[Change Uplink Interval>>doc:Main.End Device AT Commands and Downlink Command.WebHome\|\|anchor="H4.1ChangeUplinkInterval"]]
4.2	317
	318
	319
24.2	320	== 2.5 Downlink Payload ==
	321
4.2	322	By default, LSE50 prints the downlink payload to console port.
	323
24.2	324	[[image:image-20220606165544-8.png]]
4.2	325
24.2	326
32.14	327	(((
26.2	328	Examples:
32.14	329	)))
4.2	330
32.14	331	(((
	332
	333	)))
4.2	334
32.14	335	* (((
	336	Set TDC
	337	)))
4.2	338
32.14	339	(((
4.2	340	If the payload=0100003C, it means set the END Node’s TDC to 0x00003C=60(S), while type code is 01.
32.14	341	)))
4.2	342
32.14	343	(((
4.2	344	Payload: 01 00 00 1E TDC=30S
32.14	345	)))
4.2	346
32.14	347	(((
4.2	348	Payload: 01 00 00 3C TDC=60S
32.14	349	)))
4.2	350
32.14	351	(((
	352
	353	)))
4.2	354
32.14	355	* (((
	356	Reset
	357	)))
4.2	358
32.14	359	(((
4.2	360	If payload = 0x04FF, it will reset the LSE01
32.14	361	)))
4.2	362
	363
26.2	364	* CFM
4.2	365
	366	Downlink Payload: 05000001, Set AT+CFM=1 or 05000000 , set AT+CFM=0
	367
	368
26.2	369
	370	== 2.6 Show Data in DataCake IoT Server ==
	371
32.15	372	(((
4.2	373	[[DATACAKE>>url:https://datacake.co/]] provides a human friendly interface to show the sensor data, once we have data in TTN, we can use [[DATACAKE>>url:https://datacake.co/]] to connect to TTN and see the data in DATACAKE. Below are the steps:
32.15	374	)))
4.2	375
32.15	376	(((
	377
	378	)))
4.2	379
32.15	380	(((
4.2	381	Step 1: Be sure that your device is programmed and properly connected to the network at this time.
32.15	382	)))
4.2	383
32.15	384	(((
4.2	385	Step 2: To configure the Application to forward data to DATACAKE you will need to add integration. To add the DATACAKE integration, perform the following steps:
32.15	386	)))
4.2	387
	388
26.2	389	[[image:1654505857935-743.png]]
4.2	390
	391
26.2	392	[[image:1654505874829-548.png]]
4.2	393
	394	Step 3: Create an account or log in Datacake.
	395
	396	Step 4: Search the LSE01 and add DevEUI.
	397
	398
27.2	399	[[image:1654505905236-553.png]]
4.2	400
	401
	402	After added, the sensor data arrive TTN, it will also arrive and show in Mydevices.
	403
28.2	404	[[image:1654505925508-181.png]]
4.2	405
	406
	407
28.4	408	== 2.7 Frequency Plans ==
4.2	409
	410	The LSE01 uses OTAA mode and below frequency plans by default. If user want to use it with different frequency plan, please refer the AT command sets.
	411
	412
28.5	413	=== 2.7.1 EU863-870 (EU868) ===
4.2	414
28.5	415	(% style="color:#037691" %) Uplink:
	416
4.2	417	868.1 - SF7BW125 to SF12BW125
	418
	419	868.3 - SF7BW125 to SF12BW125 and SF7BW250
	420
	421	868.5 - SF7BW125 to SF12BW125
	422
	423	867.1 - SF7BW125 to SF12BW125
	424
	425	867.3 - SF7BW125 to SF12BW125
	426
	427	867.5 - SF7BW125 to SF12BW125
	428
	429	867.7 - SF7BW125 to SF12BW125
	430
	431	867.9 - SF7BW125 to SF12BW125
	432
	433	868.8 - FSK
	434
	435
28.5	436	(% style="color:#037691" %) Downlink:
4.2	437
	438	Uplink channels 1-9 (RX1)
	439
	440	869.525 - SF9BW125 (RX2 downlink only)
	441
	442
	443
28.5	444	=== 2.7.2 US902-928(US915) ===
	445
4.2	446	Used in USA, Canada and South America. Default use CHE=2
	447
28.5	448	(% style="color:#037691" %)Uplink:
4.2	449
	450	903.9 - SF7BW125 to SF10BW125
	451
	452	904.1 - SF7BW125 to SF10BW125
	453
	454	904.3 - SF7BW125 to SF10BW125
	455
	456	904.5 - SF7BW125 to SF10BW125
	457
	458	904.7 - SF7BW125 to SF10BW125
	459
	460	904.9 - SF7BW125 to SF10BW125
	461
	462	905.1 - SF7BW125 to SF10BW125
	463
	464	905.3 - SF7BW125 to SF10BW125
	465
	466
28.5	467	(% style="color:#037691" %)Downlink:
4.2	468
	469	923.3 - SF7BW500 to SF12BW500
	470
	471	923.9 - SF7BW500 to SF12BW500
	472
	473	924.5 - SF7BW500 to SF12BW500
	474
	475	925.1 - SF7BW500 to SF12BW500
	476
	477	925.7 - SF7BW500 to SF12BW500
	478
	479	926.3 - SF7BW500 to SF12BW500
	480
	481	926.9 - SF7BW500 to SF12BW500
	482
	483	927.5 - SF7BW500 to SF12BW500
	484
	485	923.3 - SF12BW500(RX2 downlink only)
	486
	487
	488
28.5	489	=== 2.7.3 CN470-510 (CN470) ===
	490
4.2	491	Used in China, Default use CHE=1
	492
28.5	493	(% style="color:#037691" %)Uplink:
4.2	494
	495	486.3 - SF7BW125 to SF12BW125
	496
	497	486.5 - SF7BW125 to SF12BW125
	498
	499	486.7 - SF7BW125 to SF12BW125
	500
	501	486.9 - SF7BW125 to SF12BW125
	502
	503	487.1 - SF7BW125 to SF12BW125
	504
	505	487.3 - SF7BW125 to SF12BW125
	506
	507	487.5 - SF7BW125 to SF12BW125
	508
	509	487.7 - SF7BW125 to SF12BW125
	510
	511
28.5	512	(% style="color:#037691" %)Downlink:
4.2	513
	514	506.7 - SF7BW125 to SF12BW125
	515
	516	506.9 - SF7BW125 to SF12BW125
	517
	518	507.1 - SF7BW125 to SF12BW125
	519
	520	507.3 - SF7BW125 to SF12BW125
	521
	522	507.5 - SF7BW125 to SF12BW125
	523
	524	507.7 - SF7BW125 to SF12BW125
	525
	526	507.9 - SF7BW125 to SF12BW125
	527
	528	508.1 - SF7BW125 to SF12BW125
	529
	530	505.3 - SF12BW125 (RX2 downlink only)
	531
	532
	533
28.5	534	=== 2.7.4 AU915-928(AU915) ===
	535
4.2	536	Default use CHE=2
	537
28.5	538	(% style="color:#037691" %)Uplink:
4.2	539
	540	916.8 - SF7BW125 to SF12BW125
	541
	542	917.0 - SF7BW125 to SF12BW125
	543
	544	917.2 - SF7BW125 to SF12BW125
	545
	546	917.4 - SF7BW125 to SF12BW125
	547
	548	917.6 - SF7BW125 to SF12BW125
	549
	550	917.8 - SF7BW125 to SF12BW125
	551
	552	918.0 - SF7BW125 to SF12BW125
	553
	554	918.2 - SF7BW125 to SF12BW125
	555
	556
28.5	557	(% style="color:#037691" %)Downlink:
4.2	558
	559	923.3 - SF7BW500 to SF12BW500
	560
	561	923.9 - SF7BW500 to SF12BW500
	562
	563	924.5 - SF7BW500 to SF12BW500
	564
	565	925.1 - SF7BW500 to SF12BW500
	566
	567	925.7 - SF7BW500 to SF12BW500
	568
	569	926.3 - SF7BW500 to SF12BW500
	570
	571	926.9 - SF7BW500 to SF12BW500
	572
	573	927.5 - SF7BW500 to SF12BW500
	574
	575	923.3 - SF12BW500(RX2 downlink only)
	576
	577
28.6	578
	579	=== 2.7.5 AS920-923 & AS923-925 (AS923) ===
	580
28.7	581	(% style="color:#037691" %)Default Uplink channel:
4.2	582
	583	923.2 - SF7BW125 to SF10BW125
	584
	585	923.4 - SF7BW125 to SF10BW125
	586
	587
28.7	588	(% style="color:#037691" %)Additional Uplink Channel:
4.2	589
	590	(OTAA mode, channel added by JoinAccept message)
	591
28.7	592	(% style="color:#037691" %)AS920~~AS923 for Japan, Malaysia, Singapore:
4.2	593
	594	922.2 - SF7BW125 to SF10BW125
	595
	596	922.4 - SF7BW125 to SF10BW125
	597
	598	922.6 - SF7BW125 to SF10BW125
	599
	600	922.8 - SF7BW125 to SF10BW125
	601
	602	923.0 - SF7BW125 to SF10BW125
	603
	604	922.0 - SF7BW125 to SF10BW125
	605
	606
28.7	607	(% style="color:#037691" %)AS923 ~~ AS925 for Brunei, Cambodia, Hong Kong, Indonesia, Laos, Taiwan, Thailand, Vietnam:
4.2	608
	609	923.6 - SF7BW125 to SF10BW125
	610
	611	923.8 - SF7BW125 to SF10BW125
	612
	613	924.0 - SF7BW125 to SF10BW125
	614
	615	924.2 - SF7BW125 to SF10BW125
	616
	617	924.4 - SF7BW125 to SF10BW125
	618
	619	924.6 - SF7BW125 to SF10BW125
	620
	621
28.7	622	(% style="color:#037691" %) Downlink:
4.2	623
	624	Uplink channels 1-8 (RX1)
	625
	626	923.2 - SF10BW125 (RX2)
	627
	628
	629
28.7	630	=== 2.7.6 KR920-923 (KR920) ===
	631
4.2	632	Default channel:
	633
	634	922.1 - SF7BW125 to SF12BW125
	635
	636	922.3 - SF7BW125 to SF12BW125
	637
	638	922.5 - SF7BW125 to SF12BW125
	639
	640
28.7	641	(% style="color:#037691" %)Uplink: (OTAA mode, channel added by JoinAccept message)
4.2	642
	643	922.1 - SF7BW125 to SF12BW125
	644
	645	922.3 - SF7BW125 to SF12BW125
	646
	647	922.5 - SF7BW125 to SF12BW125
	648
	649	922.7 - SF7BW125 to SF12BW125
	650
	651	922.9 - SF7BW125 to SF12BW125
	652
	653	923.1 - SF7BW125 to SF12BW125
	654
	655	923.3 - SF7BW125 to SF12BW125
	656
	657
28.7	658	(% style="color:#037691" %)Downlink:
4.2	659
	660	Uplink channels 1-7(RX1)
	661
	662	921.9 - SF12BW125 (RX2 downlink only; SF12BW125 might be changed to SF9BW125)
	663
	664
	665
28.7	666	=== 2.7.7 IN865-867 (IN865) ===
4.2	667
28.7	668	(% style="color:#037691" %) Uplink:
	669
4.2	670	865.0625 - SF7BW125 to SF12BW125
	671
	672	865.4025 - SF7BW125 to SF12BW125
	673
	674	865.9850 - SF7BW125 to SF12BW125
	675
	676
28.7	677	(% style="color:#037691" %) Downlink:
4.2	678
	679	Uplink channels 1-3 (RX1)
	680
	681	866.550 - SF10BW125 (RX2)
	682
	683
	684
28.7	685
	686	== 2.8 LED Indicator ==
	687
4.2	688	The LSE01 has an internal LED which is to show the status of different state.
	689
	690	* Blink once when device power on.
	691	* Solid ON for 5 seconds once device successful Join the network.
	692	* Blink once when device transmit a packet.
	693
28.8	694	== 2.9 Installation in Soil ==
	695
4.2	696	Measurement the soil surface
	697
	698
29.2	699	[[image:1654506634463-199.png]]
4.2	700
29.2	701	(((
31.8	702	(((
4.2	703	Choose the proper measuring position. Avoid the probe to touch rocks or hard things. Split the surface soil according to the measured deep. Keep the measured as original density. Vertical insert the probe into the soil to be measured. Make sure not shake when inserting.
29.2	704	)))
31.8	705	)))
4.2	706
	707
30.2	708	[[image:1654506665940-119.png]]
4.2	709
31.8	710	(((
4.2	711	Dig a hole with diameter > 20CM.
31.8	712	)))
4.2	713
31.8	714	(((
4.2	715	Horizontal insert the probe to the soil and fill the hole for long term measurement.
31.8	716	)))
4.2	717
	718
30.3	719	== 2.10 Firmware Change Log ==
4.2	720
31.7	721	(((
4.2	722	Firmware download link:
31.7	723	)))
4.2	724
31.7	725	(((
4.2	726	[[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/Firmware/]]
31.7	727	)))
4.2	728
31.7	729	(((
	730
	731	)))
4.2	732
31.7	733	(((
30.4	734	Firmware Upgrade Method: [[Firmware Upgrade Instruction>>doc:Main.Firmware Upgrade Instruction for STM32 base products.WebHome]]
31.7	735	)))
4.2	736
31.7	737	(((
	738
	739	)))
4.2	740
31.7	741	(((
4.2	742	V1.0.
31.7	743	)))
4.2	744
31.7	745	(((
4.2	746	Release
31.7	747	)))
4.2	748
	749
31.2	750	== 2.11 Battery Analysis ==
4.2	751
31.2	752	=== 2.11.1 Battery Type ===
4.2	753
31.6	754	(((
4.2	755	The LSE01 battery is a combination of a 4000mAh Li/SOCI2 Battery and a Super Capacitor. The battery is non-rechargeable battery type with a low discharge rate (<2% per year). This type of battery is commonly used in IoT devices such as water meter.
31.6	756	)))
4.2	757
31.6	758	(((
4.2	759	The battery is designed to last for more than 5 years for the LSN50.
31.6	760	)))
4.2	761
31.2	762	(((
31.6	763	(((
31.2	764	The battery-related documents are as below:
	765	)))
31.6	766	)))
4.2	767
31.2	768	* (((
	769	[[Battery Dimension>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/&file=LSN50-Battery-Dimension.pdf]],
4.2	770	)))
31.2	771	* (((
	772	[[Lithium-Thionyl Chloride Battery datasheet>>url:https://www.dragino.com/downloads/downloads/datasheet/Battery/ER26500/ER26500_Datasheet-EN.pdf]],
	773	)))
	774	* (((
	775	[[Lithium-ion Battery-Capacitor datasheet>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC_1520_datasheet.jpg]], [[Tech Spec>>url:http://www.dragino.com/downloads/downloads/datasheet/Battery/SPC1520%20Technical%20Specification20171123.pdf]]
	776	)))
4.2	777
35.2	778	[[image:image-20220610172436-1.png]]
4.2	779
	780
	781
31.2	782	=== 2.11.2 Battery Note ===
4.2	783
31.3	784	(((
4.2	785	The Li-SICO battery is designed for small current / long period application. It is not good to use a high current, short period transmit method. The recommended minimum period for use of this battery is 5 minutes. If you use a shorter period time to transmit LoRa, then the battery life may be decreased.
31.3	786	)))
4.2	787
	788
	789
31.2	790	=== 2.11.3 Replace the battery ===
	791
31.3	792	(((
4.2	793	If Battery is lower than 2.7v, user should replace the battery of LSE01.
31.3	794	)))
4.2	795
31.3	796	(((
4.2	797	You can change the battery in the LSE01.The type of battery is not limited as long as the output is between 3v to 3.6v. On the main board, there is a diode (D1) between the battery and the main circuit. If you need to use a battery with less than 3.3v, please remove the D1 and shortcut the two pads of it so there won’t be voltage drop between battery and main board.
31.3	798	)))
4.2	799
31.3	800	(((
4.2	801	The default battery pack of LSE01 includes a ER18505 plus super capacitor. If user can’t find this pack locally, they can find ER18505 or equivalence, which will also work in most case. The SPC can enlarge the battery life for high frequency use (update period below 5 minutes)
31.3	802	)))
4.2	803
	804
	805
9.2	806	= 3. Using the AT Commands =
4.2	807
9.2	808	== 3.1 Access AT Commands ==
	809
11.4	810
4.2	811	LSE01 supports AT Command set in the stock firmware. You can use a USB to TTL adapter to connect to LSE01 for using AT command, as below.
	812
31.28	813	[[image:1654501986557-872.png\|\|height="391" width="800"]]
4.2	814
	815
	816	Or if you have below board, use below connection:
	817
	818
31.28	819	[[image:1654502005655-729.png\|\|height="503" width="801"]]
4.2	820
	821
	822
11.2	823	In the PC, you need to set the serial baud rate to (% style="color:green" %)9600(%%) to access the serial console for LSE01. LSE01 will output system info once power on as below:
4.2	824
	825
31.28	826	[[image:1654502050864-459.png\|\|height="564" width="806"]]
4.2	827
	828
	829	Below are the available commands, a more detailed AT Command manual can be found at [[AT Command Manual>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/]]: [[http:~~/~~/www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/>>url:http://www.dragino.com/downloads/index.php?dir=LoRa_End_Node/LSE01/]]
	830
	831
11.4	832	(% style="background-color:#dcdcdc" %)AT+<CMD>=?AT+<CMD>? (%%) : Help on <CMD>
4.2	833
11.4	834	(% style="background-color:#dcdcdc" %)AT+<CMD>=?AT+<CMD> (%%) : Run <CMD>
4.2	835
11.4	836	(% style="background-color:#dcdcdc" %)AT+<CMD>=?AT+<CMD>=<value>(%%) : Set the value
4.2	837
11.4	838	(% style="background-color:#dcdcdc" %)AT+<CMD>=?AT+<CMD>=?(%%) : Get the value
4.2	839
	840
11.6	841	(% style="color:#037691" %)General Commands(%%)
4.2	842
11.6	843	(% style="background-color:#dcdcdc" %)AT(%%) : Attention
4.2	844
11.6	845	(% style="background-color:#dcdcdc" %)AT?(%%) : Short Help
4.2	846
11.6	847	(% style="background-color:#dcdcdc" %)ATZ(%%) : MCU Reset
4.2	848
11.6	849	(% style="background-color:#dcdcdc" %)AT+TDC(%%) : Application Data Transmission Interval
4.2	850
	851
11.4	852	(% style="color:#037691" %)Keys, IDs and EUIs management
4.2	853
11.6	854	(% style="background-color:#dcdcdc" %)AT+APPEUI(%%) : Application EUI
4.2	855
11.6	856	(% style="background-color:#dcdcdc" %)AT+APPKEY(%%) : Application Key
4.2	857
11.6	858	(% style="background-color:#dcdcdc" %)AT+APPSKEY(%%) : Application Session Key
4.2	859
11.6	860	(% style="background-color:#dcdcdc" %)AT+DADDR(%%) : Device Address
4.2	861
11.6	862	(% style="background-color:#dcdcdc" %)AT+DEUI(%%) : Device EUI
4.2	863
11.6	864	(% style="background-color:#dcdcdc" %)AT+NWKID(%%) : Network ID (You can enter this command change only after successful network connection)
4.2	865
11.6	866	(% style="background-color:#dcdcdc" %)AT+NWKSKEY(%%) : Network Session Key Joining and sending date on LoRa network
4.2	867
11.6	868	(% style="background-color:#dcdcdc" %)AT+CFM(%%) : Confirm Mode
4.2	869
11.6	870	(% style="background-color:#dcdcdc" %)AT+CFS(%%) : Confirm Status
4.2	871
11.6	872	(% style="background-color:#dcdcdc" %)AT+JOIN(%%) : Join LoRa? Network
4.2	873
11.6	874	(% style="background-color:#dcdcdc" %)AT+NJM(%%) : LoRa? Network Join Mode
4.2	875
11.6	876	(% style="background-color:#dcdcdc" %)AT+NJS(%%) : LoRa? Network Join Status
4.2	877
11.6	878	(% style="background-color:#dcdcdc" %)AT+RECV(%%) : Print Last Received Data in Raw Format
4.2	879
11.6	880	(% style="background-color:#dcdcdc" %)AT+RECVB(%%) : Print Last Received Data in Binary Format
4.2	881
11.6	882	(% style="background-color:#dcdcdc" %)AT+SEND(%%) : Send Text Data
4.2	883
11.6	884	(% style="background-color:#dcdcdc" %)AT+SENB(%%) : Send Hexadecimal Data
4.2	885
	886
11.4	887	(% style="color:#037691" %)LoRa Network Management
4.2	888
11.6	889	(% style="background-color:#dcdcdc" %)AT+ADR(%%) : Adaptive Rate
4.2	890
11.6	891	(% style="background-color:#dcdcdc" %)AT+CLASS(%%) : LoRa Class(Currently only support class A
4.2	892
11.6	893	(% style="background-color:#dcdcdc" %)AT+DCS(%%) : Duty Cycle Setting
4.2	894
11.6	895	(% style="background-color:#dcdcdc" %)AT+DR(%%) : Data Rate (Can Only be Modified after ADR=0)
4.2	896
11.6	897	(% style="background-color:#dcdcdc" %)AT+FCD(%%) : Frame Counter Downlink
4.2	898
11.6	899	(% style="background-color:#dcdcdc" %)AT+FCU(%%) : Frame Counter Uplink
4.2	900
11.6	901	(% style="background-color:#dcdcdc" %)AT+JN1DL(%%) : Join Accept Delay1
4.2	902
11.6	903	(% style="background-color:#dcdcdc" %)AT+JN2DL(%%) : Join Accept Delay2
4.2	904
11.6	905	(% style="background-color:#dcdcdc" %)AT+PNM(%%) : Public Network Mode
4.2	906
11.6	907	(% style="background-color:#dcdcdc" %)AT+RX1DL(%%) : Receive Delay1
4.2	908
11.6	909	(% style="background-color:#dcdcdc" %)AT+RX2DL(%%) : Receive Delay2
4.2	910
11.6	911	(% style="background-color:#dcdcdc" %)AT+RX2DR(%%) : Rx2 Window Data Rate
4.2	912
11.6	913	(% style="background-color:#dcdcdc" %)AT+RX2FQ(%%) : Rx2 Window Frequency
4.2	914
11.6	915	(% style="background-color:#dcdcdc" %)AT+TXP(%%) : Transmit Power
4.2	916
11.6	917	(% style="background-color:#dcdcdc" %)AT+ MOD(%%) : Set work mode
4.2	918
	919
11.4	920	(% style="color:#037691" %)Information
4.2	921
11.6	922	(% style="background-color:#dcdcdc" %)AT+RSSI(%%) : RSSI of the Last Received Packet
4.2	923
11.6	924	(% style="background-color:#dcdcdc" %)AT+SNR(%%) : SNR of the Last Received Packet
4.2	925
11.6	926	(% style="background-color:#dcdcdc" %)AT+VER(%%) : Image Version and Frequency Band
4.2	927
11.6	928	(% style="background-color:#dcdcdc" %)AT+FDR(%%) : Factory Data Reset
4.2	929
11.6	930	(% style="background-color:#dcdcdc" %)AT+PORT(%%) : Application Port
4.2	931
11.6	932	(% style="background-color:#dcdcdc" %)AT+CHS(%%) : Get or Set Frequency (Unit: Hz) for Single Channel Mode
4.2	933
11.6	934	(% style="background-color:#dcdcdc" %)AT+CHE(%%) : Get or Set eight channels mode, Only for US915, AU915, CN470
4.2	935
	936
6.3	937	= 4. FAQ =
4.2	938
6.3	939	== 4.1 How to change the LoRa Frequency Bands/Region? ==
	940
31.35	941	(((
31.24	942	You can follow the instructions for [[how to upgrade image>>\|\|anchor="H2.10200BFirmwareChangeLog"]].
4.2	943	When downloading the images, choose the required image file for download.
31.35	944	)))
4.2	945
31.35	946	(((
	947
	948	)))
4.2	949
31.35	950	(((
8.3	951	How to set up LSE01 to work in 8 channel mode By default, the frequency bands US915, AU915, CN470 work in 72 frequencies. Many gateways are 8 channel gateways, and in this case, the OTAA join time and uplink schedule is long and unpredictable while the end node is hopping in 72 frequencies.
31.35	952	)))
4.2	953
31.35	954	(((
	955
	956	)))
4.2	957
31.35	958	(((
4.2	959	You can configure the end node to work in 8 channel mode by using the AT+CHE command. The 500kHz channels are always included for OTAA.
31.35	960	)))
4.2	961
31.35	962	(((
	963
	964	)))
4.2	965
31.35	966	(((
4.2	967	For example, in US915 band, the frequency table is as below. By default, the end node will use all channels (0~~71) for OTAA Join process. After the OTAA Join, the end node will use these all channels (0~~71) to send uplink packets.
31.35	968	)))
4.2	969
8.2	970	[[image:image-20220606154726-3.png]]
4.2	971
31.36	972
4.2	973	When you use the TTN network, the US915 frequency bands use are:
	974
	975	* 903.9 - SF7BW125 to SF10BW125
	976	* 904.1 - SF7BW125 to SF10BW125
	977	* 904.3 - SF7BW125 to SF10BW125
	978	* 904.5 - SF7BW125 to SF10BW125
	979	* 904.7 - SF7BW125 to SF10BW125
	980	* 904.9 - SF7BW125 to SF10BW125
	981	* 905.1 - SF7BW125 to SF10BW125
	982	* 905.3 - SF7BW125 to SF10BW125
	983	* 904.6 - SF8BW500
	984
31.38	985	(((
4.2	986	Because the end node is now hopping in 72 frequency, it makes it difficult for the devices to Join the TTN network and uplink data. To solve this issue, you can access the device via the AT commands and run:
31.38	987	)))
4.2	988
8.3	989	(% class="box infomessage" %)
	990	(((
4.2	991	AT+CHE=2
8.3	992	)))
4.2	993
8.3	994	(% class="box infomessage" %)
	995	(((
4.2	996	ATZ
8.3	997	)))
4.2	998
31.38	999	(((
4.2	1000	to set the end node to work in 8 channel mode. The device will work in Channel 8-15 & 64-71 for OTAA, and channel 8-15 for Uplink.
31.38	1001	)))
4.2	1002
31.38	1003	(((
	1004
	1005	)))
4.2	1006
31.38	1007	(((
4.2	1008	The AU915 band is similar. Below are the AU915 Uplink Channels.
31.38	1009	)))
4.2	1010
8.2	1011	[[image:image-20220606154825-4.png]]
4.2	1012
	1013
	1014
4.8	1015	= 5. Trouble Shooting =
4.2	1016
4.9	1017	== 5.1 Why I can’t join TTN in US915 / AU915 bands? ==
	1018
4.11	1019	It is due to channel mapping. Please see the [[Eight Channel Mode>>doc:Main.LoRaWAN Communication Debug.WebHome\|\|anchor="H2.NoticeofUS9152FCN4702FAU915Frequencyband"]] section above for details.
4.2	1020
	1021
4.10	1022	== 5.2 AT Command input doesn’t work ==
4.2	1023
31.29	1024	(((
6.2	1025	In the case if user can see the console output but can’t type input to the device. Please check if you already include the (% style="color:green" %)ENTER(%%) while sending out the command. Some serial tool doesn’t send (% style="color:green" %)ENTER(%%) while press the send key, user need to add ENTER in their string.
31.29	1026	)))
4.2	1027
	1028
4.10	1029	== 5.3 Device rejoin in at the second uplink packet ==
4.2	1030
6.2	1031	(% style="color:#4f81bd" %)Issue describe as below:
4.2	1032
6.2	1033	[[image:1654500909990-784.png]]
4.2	1034
	1035
6.2	1036	(% style="color:#4f81bd" %)Cause for this issue:
4.2	1037
31.30	1038	(((
4.2	1039	The fuse on LSE01 is not large enough, some of the soil probe require large current up to 5v 800mA, in a short pulse. When this happen, it cause the device reboot so user see rejoin.
31.30	1040	)))
4.2	1041
	1042
6.2	1043	(% style="color:#4f81bd" %)Solution:
4.2	1044
	1045	All new shipped LSE01 after 2020-May-30 will have this to fix. For the customer who see this issue, please bypass the fuse as below:
	1046
31.31	1047	[[image:1654500929571-736.png\|\|height="458" width="832"]]
4.2	1048
4.7	1049
4.4	1050	= 6. Order Info =
4.2	1051
	1052
4.6	1053	Part Number: (% style="color:#4f81bd" %)LSE01-XX-YY
4.2	1054
	1055
4.6	1056	(% style="color:#4f81bd" %)XX(%%): The default frequency band
4.2	1057
4.4	1058	* (% style="color:red" %)AS923(%%): LoRaWAN AS923 band
	1059	* (% style="color:red" %)AU915(%%): LoRaWAN AU915 band
	1060	* (% style="color:red" %)EU433(%%): LoRaWAN EU433 band
	1061	* (% style="color:red" %)EU868(%%): LoRaWAN EU868 band
	1062	* (% style="color:red" %)KR920(%%): LoRaWAN KR920 band
	1063	* (% style="color:red" %)US915(%%): LoRaWAN US915 band
4.5	1064	* (% style="color:red" %)IN865(%%): LoRaWAN IN865 band
4.4	1065	* (% style="color:red" %)CN470(%%): LoRaWAN CN470 band
4.2	1066
4.4	1067	(% style="color:#4f81bd" %)YY(%%): Battery Option
4.2	1068
4.4	1069	* (% style="color:red" %)4(%%): 4000mAh battery
	1070	* (% style="color:red" %)8(%%): 8500mAh battery
4.2	1071
31.10	1072	(% class="wikigeneratedid" %)
	1073	(((
	1074
	1075	)))
	1076
4.3	1077	= 7. Packing Info =
4.2	1078
4.3	1079	(((
31.39	1080
	1081
31.40	1082	(% style="color:#037691" %)Package Includes:
4.3	1083	)))
4.2	1084
4.3	1085	* (((
	1086	LSE01 LoRaWAN Soil Moisture & EC Sensor x 1
	1087	)))
4.2	1088
4.3	1089	(((
31.40	1090
	1091
	1092	(% style="color:#037691" %)Dimension and weight:
4.3	1093	)))
4.2	1094
4.3	1095	* (((
	1096	Device Size: cm
	1097	)))
	1098	* (((
	1099	Device Weight: g
	1100	)))
	1101	* (((
	1102	Package Size / pcs : cm
	1103	)))
	1104	* (((
	1105	Weight / pcs : g
31.11	1106
	1107
4.3	1108	)))
4.2	1109
4.3	1110	= 8. Support =
4.2	1111
	1112	* Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
	1113	* Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]

Wiki source code of LSE01-LoRaWAN Soil Moisture & EC Sensor User Manual

Applications