Last modified by Mengting Qiu on 2024/04/02 16:44
<
From version < 97.8 >
edited by Xiaoling
on 2022/07/09 11:26
To version < 101.1 >
edited by Xiaoling
on 2022/07/09 15:04
>
Change comment: Uploaded new attachment "1657350248151-650.png", version {1}

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -NDDS75 NB-IoT Distance Detect Sensor User Manual
1 +N95S31B NB-IoT Temperature & Humidity Sensor User Manual
Content
... ... @@ -1,39 +1,41 @@
1 1  (% style="text-align:center" %)
2 -[[image:image-20220709085040-1.png||height="542" width="524"]]
2 +[[image:1657348034241-728.png||height="470" width="470"]]
3 3  
4 4  
5 5  
6 6  
7 7  
8 -**Table of Contents:**
9 9  
10 -{{toc/}}
11 11  
10 +**Table of Contents:**
12 12  
13 13  
14 14  
15 15  
16 16  
16 +
17 17  = 1.  Introduction =
18 18  
19 -== 1.1 ​ What is NDDS75 Distance Detection Sensor ==
19 +== 1.1 ​ What is N95S31B NB-IoT Sensor Node ==
20 20  
21 21  (((
22 22  
23 23  
24 -(((
25 -The Dragino NDDS75 is a (% style="color:blue" %)**NB-IoT Distance Detection Sensor**(%%) for Internet of Things solution. It is designed to measure the distance between the sensor and a flat object. The distance detection sensor is a module that uses ultrasonic sensing technology for distance measurement, and temperature compensation is performed internally to improve the reliability of data.
26 -\\The NDDS75 can be applied to scenarios such as horizontal distance measurement, liquid level measurement, parking management system, object proximity and presence detection, intelligent trash can management system, robot obstacle avoidance, automatic control, sewer, bottom water level monitoring, etc. It detects the distance between the measured object and the sensor, and uploads the value via wireless to IoT Server via NB-IoT Network.
27 -\\NarrowBand-Internet of Things (NB-IoT) is a standards-based low power wide area (LPWA) technology developed to enable a wide range of new IoT devices and services. NB-IoT significantly improves the power consumption of user devices, system capacity and spectrum efficiency, especially in deep coverage.
28 -\\NDDS75 supports different uplink methods include (% style="color:blue" %)**TCP, MQTT, UDP and CoAP** (%%)for different application requirement.
29 -\\NDDS75 is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), It is designed for long term use up to 5 years. (Actually Battery life depends on the use environment, update period & uplink method)
30 -\\To use NDDS75, user needs to check if there is NB-IoT coverage in local area and with the bands NDDS75 supports. If the local operate support it, user needs to get a NB-IoT SIM card from local operator and install NDDS75 to get NB-IoT network connection.
31 -)))
24 +The Dragino N95S31B is a (% style="color:blue" %)**NB-IoT Temperature and Humidity Sensor**(%%) for Internet of Things solution. It is used to measure the (% style="color:blue" %)**surrounding environment temperature and relative air humidity precisely**(%%), and then upload to IoT server via NB-IoT network*.
32 32  
26 +The temperature & humidity sensor used in N95S31B is SHT31, which is fully calibrated, linearized, and temperature compensated digital output from Sensirion, it provides a strong reliability and long-term stability. The SHT31 is fixed in a (% style="color:blue" %)**waterproof anti-condensation casing **(%%)for long term use.
27 +
28 +N95S31B supports different uplink methods include (% style="color:blue" %)**TCP, MQTT, UDP and CoAP**(%%) for different application requirement.
29 +
30 +N95S31B is powered by(% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), It is designed for long term use up to several years. (Real-world battery life depends on the use environment, update period. Please check related Power Analyze report).
31 +
32 +
33 +~* make sure you have NB-IoT coverage locally.
34 +
33 33  
34 34  )))
35 35  
36 -[[image:1657327959271-447.png]]
38 +[[image:1657348284168-431.png]]
37 37  
38 38  
39 39  
... ... @@ -41,15 +41,13 @@
41 41  
42 42  
43 43  * NB-IoT Bands: B1/B3/B8/B5/B20/B28 @H-FDD
44 -* Ultra low power consumption
45 -* Distance Detection by Ultrasonic technology
46 -* Flat object range 280mm - 7500mm
47 -* Accuracy: ±(1cm+S*0.3%) (S: Distance)
48 -* Cable Length: 25cm
46 +* Monitor Temperature & Humidity via SHT31
49 49  * AT Commands to change parameters
50 50  * Uplink on periodically
51 51  * Downlink to change configure
52 52  * IP66 Waterproof Enclosure
51 +* Ultra-Low Power consumption
52 +* AT Commands to change parameters
53 53  * Micro SIM card slot for NB-IoT SIM
54 54  * 8500mAh Battery for long term use
55 55  
... ... @@ -74,6 +74,7 @@
74 74  
75 75  (% style="color:#037691" %)**Battery:**
76 76  
77 +
77 77  * Li/SOCI2 un-chargeable battery
78 78  * Capacity: 8500mAh
79 79  * Self Discharge: <1% / Year @ 25°C
... ... @@ -80,13 +80,8 @@
80 80  * Max continuously current: 130mA
81 81  * Max boost current: 2A, 1 second
82 82  
83 -(% style="color:#037691" %)**Power Consumption**
84 84  
85 -* STOP Mode: 10uA @ 3.3v
86 -* Max transmit power: 350mA@3.3v
87 87  
88 -
89 -
90 90  == ​1.4  Applications ==
91 91  
92 92  * Smart Buildings & Home Automation
... ... @@ -102,22 +102,53 @@
102 102  
103 103  == 1.5  Pin Definitions ==
104 104  
101 +N95S31B use the mother board from NBSN95 which as below.
105 105  
106 -[[image:1657328609906-564.png]]
103 +[[image:image-20220709144723-1.png]]
107 107  
108 108  
106 +=== 1.5.1 Jumper JP2 ===
109 109  
110 -= 2.  Use NDDS75 to communicate with IoT Server =
108 +Power on Device when put this jumper.
111 111  
110 +
111 +
112 +=== 1.5.2 BOOT MODE / SW1 ===
113 +
114 +1) ISP: upgrade mode, device won't have any signal in this mode. but ready for upgrade firmware. LED won't work. Firmware won't run.
115 +
116 +2) Flash: work mode, device starts to work and send out console output for further debug
117 +
118 +
119 +
120 +=== 1.5.3 Reset Button ===
121 +
122 +Press to reboot the device.
123 +
124 +
125 +
126 +=== 1.5.4 LED ===
127 +
128 +It will flash:
129 +
130 +1. When boot the device in flash mode
131 +1. Send an uplink packet
132 +
133 +
134 +
135 +
136 += 2.  Use N95S31B to communicate with IoT Server =
137 +
112 112  == 2.1  How it works ==
113 113  
140 +
114 114  (((
115 -The NDDS75 is equipped with a NB-IoT module, the pre-loaded firmware in NDDS75 will get environment data from sensors and send the value to local NB-IoT network via the NB-IoT module.  The NB-IoT network will forward this value to IoT server via the protocol defined by NDDS75.
142 +The N95S31B is equipped with a NB-IoT module, the pre-loaded firmware in N95S31B will get environment data from sensors and send the value to local NB-IoT network via the NB-IoT module.  The NB-IoT network will forward this value to IoT server via the protocol defined by N95S31B.
116 116  )))
117 117  
118 118  
119 119  (((
120 -The diagram below shows the working flow in default firmware of NDDS75:
147 +The diagram below shows the working flow in default firmware of N95S31B:
121 121  )))
122 122  
123 123  (((
... ... @@ -212,18 +212,30 @@
212 212  (% style="color:red" %)Note: if you don't have CoAP server, you can refer this link to set up one: (%%)[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/>>http://wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/]]
213 213  
214 214  
242 +(((
215 215  **Use below commands:**
244 +)))
216 216  
217 -* (% style="color:blue" %)**AT+PRO=1**  (%%) ~/~/ Set to use CoAP protocol to uplink
218 -* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5683   ** (%%)~/~/ to set CoAP server address and port
219 -* (% style="color:blue" %)**AT+URI=5,11,"mqtt",11,"coap",12,"0",15,"c=text1",23,"0" ** (%%) ~/~/Set COAP resource path
246 +* (((
247 +(% style="color:blue" %)**AT+PRO=1**  (%%) ~/~/ Set to use CoAP protocol to uplink
248 +)))
249 +* (((
250 +(% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5683   ** (%%)~/~/ to set CoAP server address and port
251 +)))
252 +* (((
253 +(% style="color:blue" %)**AT+URI=5,11,"mqtt",11,"coap",12,"0",15,"c=text1",23,"0" ** (%%) ~/~/Set COAP resource path
254 +)))
220 220  
256 +(((
221 221  For parameter description, please refer to AT command set
258 +)))
222 222  
223 223  [[image:1657330452568-615.png]]
224 224  
225 225  
263 +(((
226 226  After configure the server address and (% style="color:green" %)**reset the device**(%%) (via AT+ATZ ), NDDS75 will start to uplink sensor values to CoAP server.
265 +)))
227 227  
228 228  [[image:1657330472797-498.png]]
229 229  
... ... @@ -246,11 +246,11 @@
246 246  === 2.2.6 Use MQTT protocol to uplink data ===
247 247  
248 248  
249 -* (% style="color:blue" %)**AT+PRO=3   ** (%%) ~/~/Set to use MQTT protocol to uplink
250 -* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,1883   ** (%%) ~/~/Set MQTT server address and port
251 -* (% style="color:blue" %)**AT+CLIENT=CLIENT       ** (%%)~/~/Set up the CLIENT of MQTT
252 -* (% style="color:blue" %)**AT+UNAME=UNAME                               **(%%)~/~/Set the username of MQTT
253 -* (% style="color:blue" %)**AT+PWD=PWD                                        **(%%)~/~/Set the password of MQTT
288 +* (% style="color:blue" %)**AT+PRO=3   ** (%%) ~/~/Set to use MQTT protocol to uplink
289 +* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,1883   ** (%%) ~/~/Set MQTT server address and port
290 +* (% style="color:blue" %)**AT+CLIENT=CLIENT       ** (%%)~/~/Set up the CLIENT of MQTT
291 +* (% style="color:blue" %)**AT+UNAME=UNAME                                **(%%)~/~/Set the username of MQTT
292 +* (% style="color:blue" %)**AT+PWD=PWD                                         **(%%)~/~/Set the password of MQTT
254 254  * (% style="color:blue" %)**AT+PUBTOPIC=NDDS75_PUB                 **(%%)~/~/Set the sending topic of MQTT
255 255  * (% style="color:blue" %)**AT+SUBTOPIC=NDDS75_SUB          **(%%) ~/~/Set the subscription topic of MQTT
256 256  
... ... @@ -300,10 +300,10 @@
300 300  In this mode, uplink payload includes in total 14 bytes
301 301  
302 302  
303 -(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:510px" %)
304 -|=(% style="width: 80px;" %)(((
342 +(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:440px" %)
343 +|=(% style="width: 60px;" %)(((
305 305  **Size(bytes)**
306 -)))|=(% style="width: 80px;" %)**6**|=(% style="width: 35px;" %)2|=(% style="width: 35px;" %)**2**|=(% style="width: 110px;" %)**1**|=(% style="width: 110px;" %)**2**|=(% style="width: 70px;" %)**1**
345 +)))|=(% style="width: 60px;" %)**6**|=(% style="width: 35px;" %)2|=(% style="width: 35px;" %)**2**|=(% style="width: 80px;" %)**1**|=(% style="width: 100px;" %)**2**|=(% style="width: 60px;" %)**1**
307 307  |(% style="width:97px" %)**Value**|(% style="width:83px" %)[[Device ID>>||anchor="H2.4.1A0A0DeviceID"]]|(% style="width:41px" %)[[Ver>>||anchor="H2.4.2A0VersionInfo"]]|(% style="width:46px" %)[[BAT>>||anchor="H2.4.3A0BatteryInfo"]]|(% style="width:123px" %)[[Signal Strength>>||anchor="H2.4.4A0SignalStrength"]]|(% style="width:120px" %)[[Distance (unit: mm)>>||anchor="H2.4.5A0Distance"]]|(% style="width:80px" %)[[Interrupt>>||anchor="H2.4.6A0DigitalInterrupt"]]
308 308  
309 309  (((
... ... @@ -432,7 +432,9 @@
432 432  
433 433  Get the distance. Flat object range 280mm - 7500mm.
434 434  
474 +(((
435 435  For example, if the data you get from the register is **__0x0B 0x05__**, the distance between the sensor and the measured object is
476 +)))
436 436  
437 437  (((
438 438  (((
... ... @@ -575,7 +575,9 @@
575 575  == 2.7  ​Firmware Change Log ==
576 576  
577 577  
619 +(((
578 578  Download URL & Firmware Change log
621 +)))
579 579  
580 580  (((
581 581  [[https:~~/~~/www.dragino.com/downloads/index.php?dir=NB-IoT/NDDS75/Firmware/>>url:https://www.dragino.com/downloads/index.php?dir=NB-IoT/NDDS75/Firmware/]]
... ... @@ -582,7 +582,9 @@
582 582  )))
583 583  
584 584  
628 +(((
585 585  Upgrade Instruction: [[Upgrade_Firmware>>||anchor="H5.1200BHowtoUpgradeFirmware"]]
630 +)))
586 586  
587 587  
588 588  
1657348034241-728.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +127.8 KB
Content
1657348284168-431.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +93.5 KB
Content
1657350248151-650.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +126.1 KB
Content
image-20220709144723-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Xiaoling
Size
... ... @@ -1,0 +1,1 @@
1 +413.1 KB
Content

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0