Last modified by Mengting Qiu on 2024/04/02 16:44
<
From version < 97.1 >
edited by Xiaoling
on 2022/07/09 11:06
To version < 97.18 >
edited by Xiaoling
on 2022/07/09 11:54
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -22,20 +22,34 @@
22 22  
23 23  
24 24  (((
25 +(((
25 25  The Dragino NDDS75 is a (% style="color:blue" %)**NB-IoT Distance Detection Sensor**(%%) for Internet of Things solution. It is designed to measure the distance between the sensor and a flat object. The distance detection sensor is a module that uses ultrasonic sensing technology for distance measurement, and temperature compensation is performed internally to improve the reliability of data.
26 -\\The NDDS75 can be applied to scenarios such as horizontal distance measurement, liquid level measurement, parking management system, object proximity and presence detection, intelligent trash can management system, robot obstacle avoidance, automatic control, sewer, bottom water level monitoring, etc. It detects the distance between the measured object and the sensor, and uploads the value via wireless to IoT Server via NB-IoT Network.
27 -\\NarrowBand-Internet of Things (NB-IoT) is a standards-based low power wide area (LPWA) technology developed to enable a wide range of new IoT devices and services. NB-IoT significantly improves the power consumption of user devices, system capacity and spectrum efficiency, especially in deep coverage.
28 -\\NDDS75 supports different uplink methods include (% style="color:blue" %)**TCP, MQTT, UDP and CoAP** (%%)for different application requirement.
29 -\\NDDS75 is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), It is designed for long term use up to 5 years. (Actually Battery life depends on the use environment, update period & uplink method)
30 -\\To use NDDS75, user needs to check if there is NB-IoT coverage in local area and with the bands NDDS75 supports. If the local operate support it, user needs to get a NB-IoT SIM card from local operator and install NDDS75 to get NB-IoT network connection.
31 31  )))
32 32  
33 -
29 +(((
30 +The NDDS75 can be applied to scenarios such as horizontal distance measurement, liquid level measurement, parking management system, object proximity and presence detection, intelligent trash can management system, robot obstacle avoidance, automatic control, sewer, bottom water level monitoring, etc. It detects the distance between the measured object and the sensor, and uploads the value via wireless to IoT Server via NB-IoT Network.
34 34  )))
35 35  
36 -[[image:1654503236291-817.png]]
33 +(((
34 +NarrowBand-Internet of Things (NB-IoT) is a standards-based low power wide area (LPWA) technology developed to enable a wide range of new IoT devices and services. NB-IoT significantly improves the power consumption of user devices, system capacity and spectrum efficiency, especially in deep coverage.
35 +)))
37 37  
37 +(((
38 +NDDS75 supports different uplink methods include (% style="color:blue" %)**TCP, MQTT, UDP and CoAP** (%%)for different application requirement.
39 +)))
38 38  
41 +(((
42 +NDDS75 is powered by (% style="color:blue" %)**8500mAh Li-SOCI2 battery**(%%), It is designed for long term use up to 5 years. (Actually Battery life depends on the use environment, update period & uplink method)
43 +)))
44 +
45 +(((
46 +To use NDDS75, user needs to check if there is NB-IoT coverage in local area and with the bands NDDS75 supports. If the local operate support it, user needs to get a NB-IoT SIM card from local operator and install NDDS75 to get NB-IoT network connection.
47 +)))
48 +)))
49 +
50 +
51 +)))
52 +
39 39  [[image:1657327959271-447.png]]
40 40  
41 41  
... ... @@ -84,9 +84,8 @@
84 84  (% style="color:#037691" %)**Power Consumption**
85 85  
86 86  * STOP Mode: 10uA @ 3.3v
87 -* Max transmit power: [[350mA@3.3v>>mailto:350mA@3.3v]]
101 +* Max transmit power: 350mA@3.3v
88 88  
89 -
90 90  == ​1.4  Applications ==
91 91  
92 92  * Smart Buildings & Home Automation
... ... @@ -100,7 +100,6 @@
100 100  ​
101 101  
102 102  
103 -
104 104  == 1.5  Pin Definitions ==
105 105  
106 106  
... ... @@ -213,18 +213,30 @@
213 213  (% style="color:red" %)Note: if you don't have CoAP server, you can refer this link to set up one: (%%)[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/>>http://wiki.dragino.com/xwiki/bin/view/Main/Set%20up%20CoAP%20Server/]]
214 214  
215 215  
228 +(((
216 216  **Use below commands:**
230 +)))
217 217  
218 -* (% style="color:blue" %)**AT+PRO=1**  (%%) ~/~/ Set to use CoAP protocol to uplink
219 -* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5683   ** (%%)~/~/ to set CoAP server address and port
220 -* (% style="color:blue" %)**AT+URI=5,11,"mqtt",11,"coap",12,"0",15,"c=text1",23,"0" ** (%%) ~/~/Set COAP resource path
232 +* (((
233 +(% style="color:blue" %)**AT+PRO=1**  (%%) ~/~/ Set to use CoAP protocol to uplink
234 +)))
235 +* (((
236 +(% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5683   ** (%%)~/~/ to set CoAP server address and port
237 +)))
238 +* (((
239 +(% style="color:blue" %)**AT+URI=5,11,"mqtt",11,"coap",12,"0",15,"c=text1",23,"0" ** (%%) ~/~/Set COAP resource path
240 +)))
221 221  
242 +(((
222 222  For parameter description, please refer to AT command set
244 +)))
223 223  
224 224  [[image:1657330452568-615.png]]
225 225  
226 226  
249 +(((
227 227  After configure the server address and (% style="color:green" %)**reset the device**(%%) (via AT+ATZ ), NDDS75 will start to uplink sensor values to CoAP server.
251 +)))
228 228  
229 229  [[image:1657330472797-498.png]]
230 230  
... ... @@ -233,9 +233,9 @@
233 233  === 2.2.5 Use UDP protocol to uplink data(Default protocol) ===
234 234  
235 235  
236 -* (% style="color:blue" %)**AT+PRO=2   ** (%%) ~/~/ Set to use UDP protocol to uplink
260 +* (% style="color:blue" %)**AT+PRO=2   ** (%%) ~/~/ Set to use UDP protocol to uplink
237 237  * (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,5601   ** (%%) ~/~/ to set UDP server address and port
238 -* (% style="color:blue" %)**AT+CFM=1       ** (%%) ~/~/If the server does not respond, this command is unnecessary
262 +* (% style="color:blue" %)**AT+CFM=1       ** (%%) ~/~/ If the server does not respond, this command is unnecessary
239 239  
240 240  [[image:1657330501006-241.png]]
241 241  
... ... @@ -247,11 +247,11 @@
247 247  === 2.2.6 Use MQTT protocol to uplink data ===
248 248  
249 249  
250 -* (% style="color:blue" %)**AT+PRO=3   ** (%%) ~/~/Set to use MQTT protocol to uplink
251 -* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,1883   ** (%%) ~/~/Set MQTT server address and port
252 -* (% style="color:blue" %)**AT+CLIENT=CLIENT       ** (%%)~/~/Set up the CLIENT of MQTT
253 -* (% style="color:blue" %)**AT+UNAME=UNAME                               **(%%)~/~/Set the username of MQTT
254 -* (% style="color:blue" %)**AT+PWD=PWD                                        **(%%)~/~/Set the password of MQTT
274 +* (% style="color:blue" %)**AT+PRO=3   ** (%%) ~/~/Set to use MQTT protocol to uplink
275 +* (% style="color:blue" %)**AT+SERVADDR=120.24.4.116,1883   ** (%%) ~/~/Set MQTT server address and port
276 +* (% style="color:blue" %)**AT+CLIENT=CLIENT       ** (%%)~/~/Set up the CLIENT of MQTT
277 +* (% style="color:blue" %)**AT+UNAME=UNAME                                **(%%)~/~/Set the username of MQTT
278 +* (% style="color:blue" %)**AT+PWD=PWD                                         **(%%)~/~/Set the password of MQTT
255 255  * (% style="color:blue" %)**AT+PUBTOPIC=NDDS75_PUB                 **(%%)~/~/Set the sending topic of MQTT
256 256  * (% style="color:blue" %)**AT+SUBTOPIC=NDDS75_SUB          **(%%) ~/~/Set the subscription topic of MQTT
257 257  
... ... @@ -301,11 +301,11 @@
301 301  In this mode, uplink payload includes in total 14 bytes
302 302  
303 303  
304 -(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:510px" %)
305 -|=(% style="width: 80px;" %)(((
328 +(% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:440px" %)
329 +|=(% style="width: 60px;" %)(((
306 306  **Size(bytes)**
307 -)))|=(% style="width: 80px;" %)**6**|=(% style="width: 35px;" %)2|=(% style="width: 35px;" %)**2**|=(% style="width: 110px;" %)**1**|=(% style="width: 110px;" %)**2**|=(% style="width: 70px;" %)**1**
308 -|(% style="width:97px" %)**Value**|(% style="width:83px" %)[[Device ID>>||anchor="H2.4.1A0A0DeviceID"]]|(% style="width:41px" %)[[Ver>>||anchor="H2.4.2A0VersionInfo"]]|(% style="width:46px" %)[[BAT>>||anchor="H2.4.3A0BatteryInfo"]]|(% style="width:123px" %)[[Signal Strength>>||anchor="H2.4.4A0SignalStrength"]]|(% style="width:120px" %)[[Distance (unit: mm)>>||anchor="H2.4.5A0Distance"]]|(% style="width:80px" %)[[Interrupt>>||anchor="H2.4.8A0DigitalInterrupt"]]
331 +)))|=(% style="width: 60px;" %)**6**|=(% style="width: 35px;" %)2|=(% style="width: 35px;" %)**2**|=(% style="width: 80px;" %)**1**|=(% style="width: 100px;" %)**2**|=(% style="width: 60px;" %)**1**
332 +|(% style="width:97px" %)**Value**|(% style="width:83px" %)[[Device ID>>||anchor="H2.4.1A0A0DeviceID"]]|(% style="width:41px" %)[[Ver>>||anchor="H2.4.2A0VersionInfo"]]|(% style="width:46px" %)[[BAT>>||anchor="H2.4.3A0BatteryInfo"]]|(% style="width:123px" %)[[Signal Strength>>||anchor="H2.4.4A0SignalStrength"]]|(% style="width:120px" %)[[Distance (unit: mm)>>||anchor="H2.4.5A0Distance"]]|(% style="width:80px" %)[[Interrupt>>||anchor="H2.4.6A0DigitalInterrupt"]]
309 309  
310 310  (((
311 311  If we use the MQTT client to subscribe to this MQTT topic, we can see the following information when the NDDS751 uplink data.
... ... @@ -388,10 +388,6 @@
388 388  === 2.4.3  Battery Info ===
389 389  
390 390  (((
391 -Check the battery voltage for LSE01.
392 -)))
393 -
394 -(((
395 395  Ex1: 0x0B45 = 2885mV
396 396  )))
397 397  
... ... @@ -437,7 +437,9 @@
437 437  
438 438  Get the distance. Flat object range 280mm - 7500mm.
439 439  
460 +(((
440 440  For example, if the data you get from the register is **__0x0B 0x05__**, the distance between the sensor and the measured object is
462 +)))
441 441  
442 442  (((
443 443  (((
... ... @@ -580,7 +580,9 @@
580 580  == 2.7  ​Firmware Change Log ==
581 581  
582 582  
605 +(((
583 583  Download URL & Firmware Change log
607 +)))
584 584  
585 585  (((
586 586  [[https:~~/~~/www.dragino.com/downloads/index.php?dir=NB-IoT/NDDS75/Firmware/>>url:https://www.dragino.com/downloads/index.php?dir=NB-IoT/NDDS75/Firmware/]]
... ... @@ -587,7 +587,9 @@
587 587  )))
588 588  
589 589  
614 +(((
590 590  Upgrade Instruction: [[Upgrade_Firmware>>||anchor="H5.1200BHowtoUpgradeFirmware"]]
616 +)))
591 591  
592 592  
593 593  

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0