Changes for page N95S31B -- NB-IoT Temperature & Humidity Sensor User Manual

Last modified by Mengting Qiu on 2024/04/02 16:44

From version < 65.14 >

edited by Xiaoling
on 2022/07/08 15:51

To version < 64.4 >

edited by Xiaoling
on 2022/07/08 14:44

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -13,14 +13,11 @@
  **Table of Contents:**
--{{toc/}}
--
--
  = 1.  Introduction =
  == 1.1  What is LoRaWAN Soil Moisture & EC Sensor ==
@@ -28,21 +28,13 @@
  (((
--(((
  Dragino NSE01 is an (% style="color:blue" %)**NB-IOT soil moisture & EC sensor**(%%) for agricultural IoT. Used to measure the soil moisture of saline-alkali soil and loam. The soil sensor uses the FDR method to calculate soil moisture and compensates it with soil temperature and electrical conductivity. It has also been calibrated for mineral soil types at the factory.
--)))
--(((
  It can detect (% style="color:blue" %)**Soil Moisture, Soil Temperature and Soil Conductivity**(%%), and upload its value to the server wirelessly.
--)))
--(((
  The wireless technology used in NSE01 allows the device to send data at a low data rate and reach ultra-long distances, providing ultra-long-distance spread spectrum Communication.
--)))
--(((
  NSE01 are powered by (% style="color:blue" %)**8500mAh Li-SOCI2**(%%) batteries, which can be used for up to 5 years.
--)))
  )))
@@ -54,8 +54,9 @@
--== 1.2  Features ==
++== 1.2 Features ==
++
  * NB-IoT Bands: B1/B3/B8/B5/B20/B28 @H-FDD
  * Monitor Soil Moisture
  * Monitor Soil Temperature
@@ -86,7 +86,7 @@
  * - B20 @H-FDD: 800MHz
  * - B28 @H-FDD: 700MHz
--Probe(% style="color:#037691" %)** Specification:**
++(% style="color:#037691" %)**Probe Specification:**
  Measure Volume: Base on the centra pin of the probe, a cylinder with 7cm diameter and 10cm height.
@@ -136,9 +136,7 @@
  === 2.2.1  Test Requirement ===
--(((
  To use NSE01 in your city, make sure meet below requirements:
--)))
  * Your local operator has already distributed a NB-IoT Network there.
  * The local NB-IoT network used the band that NSE01 supports.
@@ -155,13 +155,9 @@
  === 2.2.2  Insert SIM card ===
--(((
  Insert the NB-IoT Card get from your provider.
--)))
--(((
  User need to take out the NB-IoT module and insert the SIM card like below:
--)))
  [[image:1657249468462-536.png]]
@@ -200,9 +200,7 @@
  [[image:image-20220708110657-3.png]]
--(((
  (% style="color:red" %)Note: the valid AT Commands can be found at: (%%)[[http:~~/~~/www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/]]
--)))
@@ -305,14 +305,12 @@
  In this mode, uplink payload includes in total 18 bytes
  (% border="1" cellspacing="10" style="background-color:#ffffcc; color:green; width:510px" %)
--|=(% style="width: 60px;" %)(((
++|=(% style="width: 50px;" %)(((
  **Size(bytes)**
--)))|=(% style="width: 50px;" %)**6**|=(% style="width: 25px;" %)2|=(% style="width: 25px;" %)**2**|=(% style="width: 70px;" %)**1**|=(% style="width: 60px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 90px;" %)**2**|=(% style="width: 50px;" %)**1**
--|(% style="width:97px" %)**Value**|(% style="width:83px" %)[[Device ID>>||anchor="H2.4.1A0A0DeviceID"]]|(% style="width:41px" %)[[Ver>>||anchor="H2.4.2A0VersionInfo"]]|(% style="width:46px" %)[[BAT>>||anchor="H2.4.3A0BatteryInfo"]]|(% style="width:123px" %)[[Signal Strength>>||anchor="H2.4.4A0SignalStrength"]]|(% style="width:108px" %)[[Soil Moisture>>||anchor="H2.4.5A0SoilMoisture"]]|(% style="width:133px" %)[[Soil Temperature>>||anchor="H2.4.6A0SoilTemperature"]]|(% style="width:159px" %)[[Soil Conductivity(EC)>>||anchor="H2.4.7A0SoilConductivity28EC29"]]|(% style="width:80px" %)[[Interrupt>>||anchor="H2.4.8A0DigitalInterrupt"]]
++)))|=(% style="width: 50px;" %)**6**|=(% style="width: 25px;" %)2|=(% style="width: 25px;" %)**2**|=(% style="width: 80px;" %)**1**|=(% style="width: 80px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 80px;" %)**2**|=(% style="width: 40px;" %)**1**
++|(% style="width:97px" %)**Value**|(% style="width:83px" %)[[Device ID>>||anchor="H"]]|(% style="width:41px" %)[[Ver>>||anchor="H"]]|(% style="width:46px" %)[[BAT>>||anchor="H"]]|(% style="width:123px" %)[[Signal Strength>>||anchor="H"]]|(% style="width:108px" %)[[Soil Moisture>>||anchor="H"]]|(% style="width:133px" %)[[Soil Temperature>>||anchor="H"]]|(% style="width:159px" %)[[Soil Conductivity(EC)>>||anchor="H"]]|(% style="width:80px" %)[[Interrupt>>||anchor="H"]]
--(((
  If we use the MQTT client to subscribe to this MQTT topic, we can see the following information when the NSE01 uplink data.
--)))
  [[image:image-20220708111918-4.png]]
@@ -332,45 +332,28 @@
  * Soil Conductivity(EC) = 0x02f9 =761 uS /cm
  * Interrupt: 0x00 = 0
--
--
--
  == 2.4  Payload Explanation and Sensor Interface ==
  === 2.4.1  Device ID ===
--(((
  By default, the Device ID equal to the last 6 bytes of IMEI.
--)))
--(((
  User can use (% style="color:blue" %)**AT+DEUI**(%%) to set Device ID
--)))
--(((
  **Example:**
--)))
--(((
  AT+DEUI=A84041F15612
--)))
--(((
  The Device ID is stored in a none-erase area, Upgrade the firmware or run AT+FDR won't erase Device ID.
--)))
  === 2.4.2  Version Info ===
--(((
  Specify the software version: 0x64=100, means firmware version 1.00.
--)))
--(((
  For example: 0x00 64 : this device is NSE01 with firmware version 1.0.0.
--)))
@@ -392,33 +392,19 @@
  === 2.4.4  Signal Strength ===
--(((
  NB-IoT Network signal Strength.
--)))
--(((
  **Ex1: 0x1d = 29**
--)))
--(((
  (% style="color:blue" %)**0**(%%)        -113dBm or less
--)))
--(((
  (% style="color:blue" %)**1**(%%)        -111dBm
--)))
--(((
  (% style="color:blue" %)**2...30**(%%) -109dBm... -53dBm
--)))
--(((
  (% style="color:blue" %)**31**  (%%)    -51dBm or greater
--)))
--(((
  (% style="color:blue" %)**99**   (%%)   Not known or not detectable
--)))
@@ -425,16 +425,12 @@
  === 2.4.5  Soil Moisture ===
  (((
--(((
  Get the moisture content of the soil. The value range of the register is 0-10000(Decimal), divide this value by 100 to get the percentage of moisture in the soil.
  )))
--)))
  (((
--(((
  For example, if the data you get from the register is **__0x05 0xDC__**, the moisture content in the soil is
  )))
--)))
  (((
@@ -449,7 +449,7 @@
  === 2.4.6  Soil Temperature ===
  (((
--Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is __**0x09 0xEC**__, the temperature content in the soil is
++ Get the temperature in the soil. The value range of the register is -4000 - +800(Decimal), divide this value by 100 to get the temperature in the soil. For example, if the data you get from the register is __**0x09 0xEC**__, the temperature content in the soil is
  )))
  (((
@@ -497,7 +497,7 @@
  (% style="color:blue" %)**AT+INTMOD=3 **(%%)   ~/~/(more info about INMOD please refer [[**AT Command Manual**>>url:https://www.dragino.com/downloads/downloads/NB-IoT/NBSN95/DRAGINO_NBSN95-NB_AT%20Commands_v1.1.0.pdf]])**.**
--The lower four bits of this data field shows if this packet is generated by interrupt or not. Click here for the hardware and software set up.
++The lower four bits of this data field shows if this packet is generated by interrupt or not. [[Click here>>||anchor="H"]] for the hardware and software set up.
  Example:
@@ -622,7 +622,7 @@
  [[www.dragino.com/downloads/index.php?dir=NB-IoT/NSE01/Firmware/>>url:http://www.dragino.com/downloads/index.php?dir=NB-IoT/NBSN50/Firmware/]]
--Upgrade Instruction: [[Upgrade_Firmware>>||anchor="H5.1200BHowtoUpgradeFirmware"]]
++Upgrade Instruction: [[Upgrade_Firmware>>||anchor="H"]]
@@ -640,7 +640,7 @@
  The battery related documents as below:
  * [[Battery Dimension>>http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
--* [[Lithium-Thionyl Chloride Battery datasheet>>http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
++* [[Lithium-Thionyl Chloride Battery>>url:http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]][[ datasheet>>https://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
  * [[Lithium-ion Battery-Capacitor datasheet>>http://www.dragino.com/downloads/index.php?dir=datasheet/Battery/ER26500/]]
  (((
@@ -809,52 +809,86 @@
  )))
  (((
--(% style="color:red" %)Notice, NSE01 and LSE01 share the same mother board. They use the same connection and method to update.
++Notice, NSE01 and LSE01 share the same mother board. They use the same connection and method to update.
  )))
++(((
++
++)))
--= 6.  Trouble Shooting =
++= 5. Trouble Shooting =
--== 6.1  Connection problem when uploading firmware ==
++== 5.1 Why I can't join TTN in US915 / AU915 bands? ==
++It is due to channel mapping. Please see the [[Eight Channel Mode>>doc:Main.End Device AT Commands and Downlink Command.WebHome||anchor="H7.19EightChannelMode"]] section above for details.
--(% class="wikigeneratedid" %)
++
++== 5.2 AT Command input doesn't work ==
++
  (((
--(% style="font-size:14px" %)**Please see: **(%%)[[http:~~/~~/wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting>>http://wiki.dragino.com/xwiki/bin/view/Main/Firmware%20Upgrade%20Instruction%20for%20STM32%20base%20products/#H3.3Troubleshooting||style="background-color: rgb(255, 255, 255); font-size: 14px;"]]
++In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
  )))
++== 5.3 Device rejoin in at the second uplink packet ==
--== 6.2  AT Command input doesn't work ==
++(% style="color:#4f81bd" %)**Issue describe as below:**
++[[image:1654500909990-784.png]]
++
++
++(% style="color:#4f81bd" %)**Cause for this issue:**
++
  (((
--In the case if user can see the console output but can't type input to the device. Please check if you already include the (% style="color:green" %)**ENTER**(%%) while sending out the command. Some serial tool doesn't send (% style="color:green" %)**ENTER**(%%) while press the send key, user need to add ENTER in their string.
++The fuse on LSE01 is not large enough, some of the soil probe require large current up to 5v 800mA, in a short pulse. When this happen, it cause the device reboot so user see rejoin.
  )))
++(% style="color:#4f81bd" %)**Solution: **
--= 7.  Order Info =
++All new shipped LSE01 after 2020-May-30 will have this to fix. For the customer who see this issue, please bypass the fuse as below:
++[[image:1654500929571-736.png||height="458" width="832"]]
--Part Number**:** (% style="color:#4f81bd" %)**NSE01**
++= 6. Order Info =
++
++Part Number**:** (% style="color:#4f81bd" %)**LSE01-XX-YY**
++
++
++(% style="color:#4f81bd" %)**XX**(%%)**:** The default frequency band
++
++* (% style="color:red" %)**AS923**(%%): LoRaWAN AS923 band
++* (% style="color:red" %)**AU915**(%%): LoRaWAN AU915 band
++* (% style="color:red" %)**EU433**(%%): LoRaWAN EU433 band
++* (% style="color:red" %)**EU868**(%%): LoRaWAN EU868 band
++* (% style="color:red" %)**KR920**(%%): LoRaWAN KR920 band
++* (% style="color:red" %)**US915**(%%): LoRaWAN US915 band
++* (% style="color:red" %)**IN865**(%%):  LoRaWAN IN865 band
++* (% style="color:red" %)**CN470**(%%): LoRaWAN CN470 band
++
++(% style="color:#4f81bd" %)**YY**(%%)**: **Battery Option
++
++* (% style="color:red" %)**4**(%%): 4000mAh battery
++* (% style="color:red" %)**8**(%%): 8500mAh battery
++
  (% class="wikigeneratedid" %)
  (((
  )))
--= 8.  Packing Info =
++= 7. Packing Info =
  (((
  (% style="color:#037691" %)**Package Includes**:
++)))
--
--* NSE01 NB-IoT Soil Moisture & EC Sensor x 1
--* External antenna x 1
++* (((
++LSE01 LoRaWAN Soil Moisture & EC Sensor x 1
  )))
  (((
@@ -861,20 +861,24 @@
  (% style="color:#037691" %)**Dimension and weight**:
++)))
--
--* Size: 195 x 125 x 55 mm
--* Weight:   420g
++* (((
++Device Size: cm
  )))
++* (((
++Device Weight: g
++)))
++* (((
++Package Size / pcs : cm
++)))
++* (((
++Weight / pcs : g
--(((
--
--
--
  )))
--= 9.  Support =
++= 8. Support =
  * Support is provided Monday to Friday, from 09:00 to 18:00 GMT+8. Due to different timezones we cannot offer live support. However, your questions will be answered as soon as possible in the before-mentioned schedule.
  * Provide as much information as possible regarding your enquiry (product models, accurately describe your problem and steps to replicate it etc) and send a mail to [[support@dragino.com>>url:http://../../../../../../D:%5C%E5%B8%82%E5%9C%BA%E8%B5%84%E6%96%99%5C%E8%AF%B4%E6%98%8E%E4%B9%A6%5CLoRa%5CLT%E7%B3%BB%E5%88%97%5Csupport@dragino.com]]

Changes for page N95S31B -- NB-IoT Temperature & Humidity Sensor User Manual

Summary

Details

Applications

Navigation